Fixes for various omap devices. It's all dts and defconfig

changes for this set:
 
 - Fix wrong DMA properties for dma to avoid them getting
   copied wrong again before we start actually using them
 
 - USB fixes to revert the extcon changes as the driver did not
   get merged yet and cause issues
 
 - Omap5 and dra7 fixes to boot from sata
 
 - Fix few am437x issues for i2c and pinctrl
 
 - Fix beaglebone for hardwared USB configuration
 
 - Defconfig changes for NAND, SATA and TPS62362
 
 - Fix n900 i2c numbering for legacy user space and smc91x
   register offset so it works also for qemu
 
 - Fix incomplete USB configuration for dm816x
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU7NU9AAoJEBvUPslcq6VzGHYP/j815CZXRptbhdWFBg/Sv2UX
 l5hpnP1lW667yEmb4haNfFUyBYPHrzk0U78WB8IsEMR9C4ZJGfaiZdSv/BDAYH5z
 AHBjOb21K+q4+830i4sWT6LsCWPaCcJ5LxBNtvPtcpFltUjJzraC9a3vtrEXLRvY
 ALij2+3epcxKeR1BO7Sy+cnFShNMXTbSIr82MQsPIX5wFOn/vzytj+/4+OBac8vY
 OhGneKsvGHGv2jvoOOhkpjFCWrojaKkdS75XIrdBp7JPKjRREr08LeoqdZMJu6BQ
 xzIVkDnSojw4Vn+R+glekDP+ldPh+HGzf6OQabyCa1o4D1hriKiauON9Odk0z8Vr
 qLnh2UwRRbNSGaGYR0OLSXUy6sZX1eBfaeoe+691t0UHLylm81ZPTuSfd7MVGElp
 sFq0Jq6dw+Ech2A1lbMAl8d8aO0CQlr5uF2+9HfoIkZxjktKmJMNuNvL3M4b4kPS
 uUgcch40vqdOyrV5qz3/Nwn/e7/hk/i23vbNgsuYauV0CxGA0c6/Nk+TP8hH8fYW
 XSFacaEEaK2Sj40Lyw6o/15Fr5rfG51vX/jNz2NgDbdJUYT42KK/Hr3AZrXQPyBf
 YQWjrL6NgcwdX2v2KhsCLyo2ABp8RgPYQVDAC8LNZNCUBar9+l6+a1e1lMfPnNKq
 4IAZO4ftH3x71V+nQMVS
 =oG7A
 -----END PGP SIGNATURE-----

Merge tag 'fixes-v4.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for various omap devices. It's all dts and defconfig
changes for this set:

- Fix wrong DMA properties for dma to avoid them getting
  copied wrong again before we start actually using them

- USB fixes to revert the extcon changes as the driver did not
  get merged yet and cause issues

- Omap5 and dra7 fixes to boot from sata

- Fix few am437x issues for i2c and pinctrl

- Fix beaglebone for hardwared USB configuration

- Defconfig changes for NAND, SATA and TPS62362

- Fix n900 i2c numbering for legacy user space and smc91x
  register offset so it works also for qemu

- Fix incomplete USB configuration for dm816x

* tag 'fixes-v4.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-bone*: usb0 is hardwired for peripheral
  ARM: dts: dra7x-evm: beagle-x15: Fix USB Host
  ARM: omap2plus_defconfig: Fix SATA boot
  ARM: omap2plus_defconfig: Enable OMAP NAND BCH driver
  ARM: dts: dra7: Correct the dma controller's property names
  ARM: dts: omap5: Correct the dma controller's property names
  ARM: dts: omap4: Correct the dma controller's property names
  ARM: dts: omap3: Correct the dma controller's property names
  ARM: dts: omap2: Correct the dma controller's property names
  ARM: dts: am437x-idk: fix sleep pinctrl state
  ARM: omap2plus_defconfig: enable TPS62362 regulator
  ARM: dts: am437x-idk: fix TPS62362 i2c bus
  ARM: dts: n900: Fix offset for smc91x ethernet
  ARM: dts: n900: fix i2c bus numbering
  ARM: dts: Fix USB dts configuration for dm816x
  ARM: dts: OMAP5: Fix SATA PHY node
  ARM: dts: DRA7: Fix SATA PHY node
This commit is contained in:
Arnd Bergmann 2015-02-25 17:12:35 +01:00
commit 6af714b069
14 changed files with 83 additions and 67 deletions

View File

@ -195,6 +195,7 @@
&usb0 {
status = "okay";
dr_mode = "peripheral";
};
&usb1 {

View File

@ -133,20 +133,6 @@
>;
};
i2c1_pins_default: i2c1_pins_default {
pinctrl-single,pins = <
0x15c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */
0x158 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */
>;
};
i2c1_pins_sleep: i2c1_pins_sleep {
pinctrl-single,pins = <
0x15c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_cs0.i2c1_scl */
0x158 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d1.i2c1_sda */
>;
};
mmc1_pins_default: pinmux_mmc1_pins_default {
pinctrl-single,pins = <
0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */
@ -254,7 +240,7 @@
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c0_pins_default>;
pinctrl-1 = <&i2c0_pins_default>;
pinctrl-1 = <&i2c0_pins_sleep>;
clock-frequency = <400000>;
at24@50 {
@ -262,17 +248,10 @@
pagesize = <64>;
reg = <0x50>;
};
};
&i2c1 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c1_pins_default>;
pinctrl-1 = <&i2c1_pins_default>;
clock-frequency = <400000>;
tps: tps62362@60 {
compatible = "ti,tps62362";
reg = <0x60>;
regulator-name = "VDD_MPU";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1330000>;

View File

@ -549,14 +549,6 @@
pinctrl-0 = <&usb1_pins>;
};
&omap_dwc3_1 {
extcon = <&extcon_usb1>;
};
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
&usb2 {
dr_mode = "peripheral";
};

View File

@ -35,6 +35,18 @@
DM816X_IOPAD(0x0aac, PIN_INPUT | MUX_MODE0) /* SPI_D1 */
>;
};
usb0_pins: pinmux_usb0_pins {
pinctrl-single,pins = <
DM816X_IOPAD(0x0d00, MUX_MODE0) /* USB0_DRVVBUS */
>;
};
usb1_pins: pinmux_usb0_pins {
pinctrl-single,pins = <
DM816X_IOPAD(0x0d04, MUX_MODE0) /* USB1_DRVVBUS */
>;
};
};
&i2c1 {
@ -127,3 +139,16 @@
&mmc1 {
vmmc-supply = <&vmmcsd_fixed>;
};
/* At least dm8168-evm rev c won't support multipoint, later may */
&usb0 {
pinctrl-names = "default";
pinctrl-0 = <&usb0_pins>;
mentor,multipoint = <0>;
};
&usb1 {
pinctrl-names = "default";
pinctrl-0 = <&usb1_pins>;
mentor,multipoint = <0>;
};

View File

@ -97,10 +97,31 @@
/* Device Configuration Registers */
scm_conf: syscon@600 {
compatible = "syscon";
compatible = "syscon", "simple-bus";
reg = <0x600 0x110>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x600 0x110>;
usb_phy0: usb-phy@20 {
compatible = "ti,dm8168-usb-phy";
reg = <0x20 0x8>;
reg-names = "phy";
clocks = <&main_fapll 6>;
clock-names = "refclk";
#phy-cells = <0>;
syscon = <&scm_conf>;
};
usb_phy1: usb-phy@28 {
compatible = "ti,dm8168-usb-phy";
reg = <0x28 0x8>;
reg-names = "phy";
clocks = <&main_fapll 6>;
clock-names = "refclk";
#phy-cells = <0>;
syscon = <&scm_conf>;
};
};
scrm_clocks: clocks {
@ -357,7 +378,10 @@
reg-names = "mc", "control";
interrupts = <18>;
interrupt-names = "mc";
dr_mode = "otg";
dr_mode = "host";
interface-type = <0>;
phys = <&usb_phy0>;
phy-names = "usb2-phy";
mentor,multipoint = <1>;
mentor,num-eps = <16>;
mentor,ram-bits = <12>;
@ -366,13 +390,15 @@
usb1: usb@47401800 {
compatible = "ti,musb-am33xx";
status = "disabled";
reg = <0x47401c00 0x400
0x47401800 0x200>;
reg-names = "mc", "control";
interrupts = <19>;
interrupt-names = "mc";
dr_mode = "otg";
dr_mode = "host";
interface-type = <0>;
phys = <&usb_phy1>;
phy-names = "usb2-phy";
mentor,multipoint = <1>;
mentor,num-eps = <16>;
mentor,ram-bits = <12>;

View File

@ -543,14 +543,6 @@
};
};
&omap_dwc3_1 {
extcon = <&extcon_usb1>;
};
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
&usb1 {
dr_mode = "peripheral";
pinctrl-names = "default";

View File

@ -249,8 +249,8 @@
<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
#dma-channels = <32>;
#dma-requests = <127>;
dma-channels = <32>;
dma-requests = <127>;
};
gpio1: gpio@4ae10000 {
@ -1090,8 +1090,8 @@
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_sata>;
clocks = <&sys_clkin1>;
clock-names = "sysclk";
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
};

View File

@ -380,14 +380,6 @@
phy-supply = <&ldo4_reg>;
};
&omap_dwc3_1 {
extcon = <&extcon_usb1>;
};
&omap_dwc3_2 {
extcon = <&extcon_usb2>;
};
&usb1 {
dr_mode = "peripheral";
pinctrl-names = "default";

View File

@ -87,8 +87,8 @@
<14>,
<15>;
#dma-cells = <1>;
#dma-channels = <32>;
#dma-requests = <64>;
dma-channels = <32>;
dma-requests = <64>;
};
i2c1: i2c@48070000 {

View File

@ -16,6 +16,13 @@
model = "Nokia N900";
compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
aliases {
i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
};
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
@ -704,7 +711,7 @@
compatible = "smsc,lan91c94";
interrupt-parent = <&gpio2>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
reg = <1 0x300 0xf>; /* 16 byte IO range at offset 0x300 */
reg = <1 0 0xf>; /* 16 byte IO range */
bank-width = <2>;
pinctrl-names = "default";
pinctrl-0 = <&ethernet_pins>;

View File

@ -155,8 +155,8 @@
<14>,
<15>;
#dma-cells = <1>;
#dma-channels = <32>;
#dma-requests = <96>;
dma-channels = <32>;
dma-requests = <96>;
};
omap3_pmx_core: pinmux@48002030 {

View File

@ -223,8 +223,8 @@
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
#dma-channels = <32>;
#dma-requests = <127>;
dma-channels = <32>;
dma-requests = <127>;
};
gpio1: gpio@4a310000 {

View File

@ -238,8 +238,8 @@
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
#dma-channels = <32>;
#dma-requests = <127>;
dma-channels = <32>;
dma-requests = <127>;
};
gpio1: gpio@4ae10000 {
@ -929,8 +929,8 @@
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_sata>;
clocks = <&sys_clkin>;
clock-names = "sysclk";
clocks = <&sys_clkin>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
};
};

View File

@ -114,6 +114,7 @@ CONFIG_MTD_PHYSMAP_OF=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ECC_BCH=y
CONFIG_MTD_NAND_OMAP2=y
CONFIG_MTD_NAND_OMAP_BCH=y
CONFIG_MTD_ONENAND=y
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
CONFIG_MTD_ONENAND_OMAP2=y
@ -248,6 +249,7 @@ CONFIG_TWL6040_CORE=y
CONFIG_REGULATOR_PALMAS=y
CONFIG_REGULATOR_PBIAS=y
CONFIG_REGULATOR_TI_ABB=y
CONFIG_REGULATOR_TPS62360=m
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
CONFIG_REGULATOR_TPS65217=y
@ -374,7 +376,7 @@ CONFIG_PWM_TIEHRPWM=m
CONFIG_PWM_TWL=m
CONFIG_PWM_TWL_LED=m
CONFIG_OMAP_USB2=m
CONFIG_TI_PIPE3=m
CONFIG_TI_PIPE3=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set