Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"
This reverts commit e917ba01d6.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
Greg Kroah-Hartman
parent
92dfe41088
commit
692ed4ddf0
|
|
@ -269,128 +269,115 @@ static int pl2303_set_control_lines(struct usb_serial_port *port, u8 value)
|
|||
return retval;
|
||||
}
|
||||
|
||||
static int pl2303_baudrate_encode_direct(int baud, enum pl2303_type type,
|
||||
u8 buf[4])
|
||||
{
|
||||
/*
|
||||
* NOTE: Only the values defined in baud_sup are supported !
|
||||
* => if unsupported values are set, the PL2303 seems to
|
||||
* use 9600 baud (at least my PL2303X always does)
|
||||
*/
|
||||
const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400, 3600,
|
||||
4800, 7200, 9600, 14400, 19200, 28800, 38400,
|
||||
57600, 115200, 230400, 460800, 614400, 921600,
|
||||
1228800, 2457600, 3000000, 6000000 };
|
||||
int i;
|
||||
|
||||
/* Set baudrate to nearest supported value */
|
||||
for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) {
|
||||
if (baud_sup[i] > baud)
|
||||
break;
|
||||
}
|
||||
if (i == ARRAY_SIZE(baud_sup))
|
||||
baud = baud_sup[i - 1];
|
||||
else if (i > 0 && (baud_sup[i] - baud) > (baud - baud_sup[i - 1]))
|
||||
baud = baud_sup[i - 1];
|
||||
else
|
||||
baud = baud_sup[i];
|
||||
/* type_0, type_1 only support up to 1228800 baud */
|
||||
if (type != HX)
|
||||
baud = min_t(int, baud, 1228800);
|
||||
/* Direct (standard) baud rate encoding method */
|
||||
put_unaligned_le32(baud, buf);
|
||||
|
||||
return baud;
|
||||
}
|
||||
|
||||
static int pl2303_baudrate_encode_divisor(int baud, enum pl2303_type type,
|
||||
u8 buf[4])
|
||||
{
|
||||
/*
|
||||
* Divisor based baud rate encoding method
|
||||
*
|
||||
* NOTE: it's not clear if the type_0/1 chips support this method
|
||||
*
|
||||
* divisor = 12MHz * 32 / baudrate = 2^A * B
|
||||
*
|
||||
* with
|
||||
*
|
||||
* A = buf[1] & 0x0e
|
||||
* B = buf[0] + (buf[1] & 0x01) << 8
|
||||
*
|
||||
* Special cases:
|
||||
* => 8 < B < 16: device seems to work not properly
|
||||
* => B <= 8: device uses the max. value B = 512 instead
|
||||
*/
|
||||
unsigned int A, B;
|
||||
|
||||
/* Respect the specified baud rate limits */
|
||||
baud = max_t(int, baud, 75);
|
||||
if (type == HX)
|
||||
baud = min_t(int, baud, 6000000);
|
||||
else
|
||||
baud = min_t(int, baud, 1228800);
|
||||
/* Determine factors A and B */
|
||||
A = 0;
|
||||
B = 12000000 * 32 / baud; /* 12MHz */
|
||||
B <<= 1; /* Add one bit for rounding */
|
||||
while (B > (512 << 1) && A <= 14) {
|
||||
A += 2;
|
||||
B >>= 2;
|
||||
}
|
||||
if (A > 14) { /* max. divisor = min. baudrate reached */
|
||||
A = 14;
|
||||
B = 512;
|
||||
/* => ~45.78 baud */
|
||||
} else {
|
||||
B = (B + 1) >> 1; /* Round the last bit */
|
||||
}
|
||||
/* Handle special cases */
|
||||
if (B == 512)
|
||||
B = 0; /* also: 1 to 8 */
|
||||
else if (B < 16)
|
||||
/*
|
||||
* NOTE: With the current algorithm this happens
|
||||
* only for A=0 and means that the min. divisor
|
||||
* (respectively: the max. baudrate) is reached.
|
||||
*/
|
||||
B = 16; /* => 24 MBaud */
|
||||
/* Encode the baud rate */
|
||||
buf[3] = 0x80; /* Select divisor encoding method */
|
||||
buf[2] = 0;
|
||||
buf[1] = (A & 0x0e); /* A */
|
||||
buf[1] |= ((B & 0x100) >> 8); /* MSB of B */
|
||||
buf[0] = B & 0xff; /* 8 LSBs of B */
|
||||
/* Calculate the actual/resulting baud rate */
|
||||
if (B <= 8)
|
||||
B = 512;
|
||||
baud = 12000000 * 32 / ((1 << A) * B);
|
||||
|
||||
return baud;
|
||||
}
|
||||
|
||||
static void pl2303_encode_baudrate(struct tty_struct *tty,
|
||||
struct usb_serial_port *port,
|
||||
enum pl2303_type type,
|
||||
u8 buf[4])
|
||||
{
|
||||
struct usb_serial *serial = port->serial;
|
||||
struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
|
||||
int baud;
|
||||
|
||||
baud = tty_get_baud_rate(tty);
|
||||
dev_dbg(&port->dev, "baud requested = %d\n", baud);
|
||||
if (!baud)
|
||||
return;
|
||||
/*
|
||||
* There are two methods for setting/encoding the baud rate
|
||||
* 1) Direct method: encodes the baud rate value directly
|
||||
* => supported by all chip types
|
||||
* 2) Divisor based method: encodes a divisor to a base value (12MHz*32)
|
||||
* => supported by HX chips (and likely not by type_0/1 chips)
|
||||
*/
|
||||
if (type != HX || baud <= 115200)
|
||||
baud = pl2303_baudrate_encode_direct(baud, type, buf);
|
||||
else
|
||||
baud = pl2303_baudrate_encode_divisor(baud, type, buf);
|
||||
|
||||
if (spriv->type != HX || baud <= 115200) {
|
||||
/*
|
||||
* NOTE: Only the values defined in baud_sup are supported !
|
||||
* => if unsupported values are set, the PL2303 seems to
|
||||
* use 9600 baud (at least my PL2303X always does)
|
||||
*/
|
||||
const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400,
|
||||
3600, 4800, 7200, 9600, 14400, 19200,
|
||||
28800, 38400, 57600, 115200, 230400,
|
||||
460800, 614400, 921600, 1228800,
|
||||
2457600, 3000000, 6000000 };
|
||||
int i;
|
||||
|
||||
/* Set baudrate to nearest supported value */
|
||||
for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) {
|
||||
if (baud_sup[i] > baud)
|
||||
break;
|
||||
}
|
||||
|
||||
if (i == ARRAY_SIZE(baud_sup))
|
||||
baud = baud_sup[i - 1];
|
||||
else if (i > 0
|
||||
&& (baud_sup[i] - baud) > (baud - baud_sup[i - 1]))
|
||||
baud = baud_sup[i - 1];
|
||||
else
|
||||
baud = baud_sup[i];
|
||||
|
||||
/* type_0, type_1 only support up to 1228800 baud */
|
||||
if (spriv->type != HX)
|
||||
baud = min_t(int, baud, 1228800);
|
||||
|
||||
/* Direct (standard) baud rate encoding method */
|
||||
put_unaligned_le32(baud, buf);
|
||||
} else {
|
||||
/*
|
||||
* Divisor based baud rate encoding method
|
||||
*
|
||||
* NOTE: it's not clear if the type_0/1 chips
|
||||
* support this method
|
||||
*
|
||||
* divisor = 12MHz * 32 / baudrate = 2^A * B
|
||||
*
|
||||
* with
|
||||
*
|
||||
* A = buf[1] & 0x0e
|
||||
* B = buf[0] + (buf[1] & 0x01) << 8
|
||||
*
|
||||
* Special cases:
|
||||
* => 8 < B < 16: device seems to work not properly
|
||||
* => B <= 8: device uses the max. value B = 512 instead
|
||||
*/
|
||||
unsigned int A, B;
|
||||
|
||||
/* Respect the specified baud rate limits */
|
||||
baud = max_t(int, baud, 75);
|
||||
if (spriv->type == HX)
|
||||
baud = min_t(int, baud, 6000000);
|
||||
else
|
||||
baud = min_t(int, baud, 1228800);
|
||||
/* Determine factors A and B */
|
||||
A = 0;
|
||||
B = 12000000 * 32 / baud; /* 12MHz */
|
||||
B <<= 1; /* Add one bit for rounding */
|
||||
while (B > (512 << 1) && A <= 14) {
|
||||
A += 2;
|
||||
B >>= 2;
|
||||
}
|
||||
if (A > 14) { /* max. divisor = min. baudrate reached */
|
||||
A = 14;
|
||||
B = 512;
|
||||
/* => ~45.78 baud */
|
||||
} else {
|
||||
B = (B + 1) >> 1; /* Round the last bit */
|
||||
}
|
||||
/* Handle special cases */
|
||||
if (B == 512)
|
||||
B = 0; /* also: 1 to 8 */
|
||||
else if (B < 16)
|
||||
/*
|
||||
* NOTE: With the current algorithm this happens
|
||||
* only for A=0 and means that the min. divisor
|
||||
* (respectively: the max. baudrate) is reached.
|
||||
*/
|
||||
B = 16; /* => 24 MBaud */
|
||||
/* Encode the baud rate */
|
||||
buf[3] = 0x80; /* Select divisor encoding method */
|
||||
buf[2] = 0;
|
||||
buf[1] = (A & 0x0e); /* A */
|
||||
buf[1] |= ((B & 0x100) >> 8); /* MSB of B */
|
||||
buf[0] = B & 0xff; /* 8 LSBs of B */
|
||||
/* Calculate the actual/resulting baud rate */
|
||||
if (B <= 8)
|
||||
B = 512;
|
||||
baud = 12000000 * 32 / ((1 << A) * B);
|
||||
}
|
||||
|
||||
/* Save resulting baud rate */
|
||||
tty_encode_baud_rate(tty, baud, baud);
|
||||
dev_dbg(&port->dev, "baud set = %d\n", baud);
|
||||
|
|
@ -447,8 +434,8 @@ static void pl2303_set_termios(struct tty_struct *tty,
|
|||
dev_dbg(&port->dev, "data bits = %d\n", buf[6]);
|
||||
}
|
||||
|
||||
/* For reference: buf[0]:buf[3] baud rate value */
|
||||
pl2303_encode_baudrate(tty, port, spriv->type, buf);
|
||||
/* For reference buf[0]:buf[3] baud rate value */
|
||||
pl2303_encode_baudrate(tty, port, &buf[0]);
|
||||
|
||||
/* For reference buf[4]=0 is 1 stop bits */
|
||||
/* For reference buf[4]=1 is 1.5 stop bits */
|
||||
|
|
|
|||
Loading…
Reference in New Issue