[media] DocBook: convert struct tuner_parms to doc-nano format
The struct tuner_params is almost fully documented, but using a non-standard way. Convert it to doc-nano format, and add descriptions for the parameters that aren't documented yet. Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commit is contained in:
Mauro Carvalho Chehab
parent
62e93f090b
commit
65fc64090e
|
|
@ -19,91 +19,119 @@ struct tuner_range {
|
|||
unsigned char cb;
|
||||
};
|
||||
|
||||
/**
|
||||
* struct tuner_params - Parameters to be used to setup the tuner. Those
|
||||
* are used by drivers/media/tuners/tuner-types.c in
|
||||
* order to specify the tuner properties. Most of
|
||||
* the parameters are for tuners based on tda9887 IF-PLL
|
||||
* multi-standard analog TV/Radio demodulator, with is
|
||||
* very common on legacy analog tuners.
|
||||
*
|
||||
* @type: Type of the tuner parameters, as defined at
|
||||
* enum param_type. If the tuner supports multiple
|
||||
* standards, an array should be used, with one
|
||||
* row per different standard.
|
||||
* @cb_first_if_lower_freq: Many Philips-based tuners have a comment in
|
||||
* their datasheet like
|
||||
* "For channel selection involving band
|
||||
* switching, and to ensure smooth tuning to the
|
||||
* desired channel without causing unnecessary
|
||||
* charge pump action, it is recommended to
|
||||
* consider the difference between wanted channel
|
||||
* frequency and the current channel frequency.
|
||||
* Unnecessary charge pump action will result
|
||||
* in very low tuning voltage which may drive the
|
||||
* oscillator to extreme conditions".
|
||||
* Set cb_first_if_lower_freq to 1, if this check
|
||||
* is required for this tuner. I tested this for
|
||||
* PAL by first setting the TV frequency to
|
||||
* 203 MHz and then switching to 96.6 MHz FM
|
||||
* radio. The result was static unless the
|
||||
* control byte was sent first.
|
||||
* @has_tda9887: Set to 1 if this tuner uses a tda9887
|
||||
* @port1_fm_high_sensitivity: Many Philips tuners use tda9887 PORT1 to select
|
||||
* the FM radio sensitivity. If this setting is 1,
|
||||
* then set PORT1 to 1 to get proper FM reception.
|
||||
* @port2_fm_high_sensitivity: Some Philips tuners use tda9887 PORT2 to select
|
||||
* the FM radio sensitivity. If this setting is 1,
|
||||
* then set PORT2 to 1 to get proper FM reception.
|
||||
* @fm_gain_normal: Some Philips tuners use tda9887 cGainNormal to
|
||||
* select the FM radio sensitivity. If this
|
||||
* setting is 1, e register will use cGainNormal
|
||||
* instead of cGainLow.
|
||||
* @intercarrier_mode: Most tuners with a tda9887 use QSS mode.
|
||||
* Some (cheaper) tuners use Intercarrier mode.
|
||||
* If this setting is 1, then the tuner needs to
|
||||
* be set to intercarrier mode.
|
||||
* @port1_active: This setting sets the default value for PORT1.
|
||||
* 0 means inactive, 1 means active. Note: the
|
||||
* actual bit value written to the tda9887 is
|
||||
* inverted. So a 0 here means a 1 in the B6 bit.
|
||||
* @port2_active: This setting sets the default value for PORT2.
|
||||
* 0 means inactive, 1 means active. Note: the
|
||||
* actual bit value written to the tda9887 is
|
||||
* inverted. So a 0 here means a 1 in the B7 bit.
|
||||
* @port1_invert_for_secam_lc: Sometimes PORT1 is inverted when the SECAM-L'
|
||||
* standard is selected. Set this bit to 1 if this
|
||||
* is needed.
|
||||
* @port2_invert_for_secam_lc: Sometimes PORT2 is inverted when the SECAM-L'
|
||||
* standard is selected. Set this bit to 1 if this
|
||||
* is needed.
|
||||
* @port1_set_for_fm_mono: Some cards require PORT1 to be 1 for mono Radio
|
||||
* FM and 0 for stereo.
|
||||
* @default_pll_gating_18: Select 18% (or according to datasheet 0%)
|
||||
* L standard PLL gating, vs the driver default
|
||||
* of 36%.
|
||||
* @radio_if: IF to use in radio mode. Tuners with a
|
||||
* separate radio IF filter seem to use 10.7,
|
||||
* while those without use 33.3 for PAL/SECAM
|
||||
* tuners and 41.3 for NTSC tuners.
|
||||
* 0 = 10.7, 1 = 33.3, 2 = 41.3
|
||||
* @default_top_low: Default tda9887 TOP value in dB for the low
|
||||
* band. Default is 0. Range: -16:+15
|
||||
* @default_top_mid: Default tda9887 TOP value in dB for the mid
|
||||
* band. Default is 0. Range: -16:+15
|
||||
* @default_top_high: Default tda9887 TOP value in dB for the high
|
||||
* band. Default is 0. Range: -16:+15
|
||||
* @default_top_secam_low: Default tda9887 TOP value in dB for SECAM-L/L'
|
||||
* for the low band. Default is 0. Several tuners
|
||||
* require a different TOP value for the
|
||||
* SECAM-L/L' standards. Range: -16:+15
|
||||
* @default_top_secam_mid: Default tda9887 TOP value in dB for SECAM-L/L'
|
||||
* for the mid band. Default is 0. Several tuners
|
||||
* require a different TOP value for the
|
||||
* SECAM-L/L' standards. Range: -16:+15
|
||||
* @default_top_secam_high: Default tda9887 TOP value in dB for SECAM-L/L'
|
||||
* for the high band. Default is 0. Several tuners
|
||||
* require a different TOP value for the
|
||||
* SECAM-L/L' standards. Range: -16:+15
|
||||
* @iffreq: Intermediate frequency (IF) used by the tuner
|
||||
* on digital mode.
|
||||
* @count: Size of the ranges array.
|
||||
* @ranges: Array with the frequency ranges supported by
|
||||
* the tuner.
|
||||
*/
|
||||
struct tuner_params {
|
||||
enum param_type type;
|
||||
|
||||
/* Many Philips based tuners have a comment like this in their
|
||||
* datasheet:
|
||||
*
|
||||
* For channel selection involving band switching, and to ensure
|
||||
* smooth tuning to the desired channel without causing
|
||||
* unnecessary charge pump action, it is recommended to consider
|
||||
* the difference between wanted channel frequency and the
|
||||
* current channel frequency. Unnecessary charge pump action
|
||||
* will result in very low tuning voltage which may drive the
|
||||
* oscillator to extreme conditions.
|
||||
*
|
||||
* Set cb_first_if_lower_freq to 1, if this check is
|
||||
* required for this tuner.
|
||||
*
|
||||
* I tested this for PAL by first setting the TV frequency to
|
||||
* 203 MHz and then switching to 96.6 MHz FM radio. The result was
|
||||
* static unless the control byte was sent first.
|
||||
*/
|
||||
unsigned int cb_first_if_lower_freq:1;
|
||||
/* Set to 1 if this tuner uses a tda9887 */
|
||||
unsigned int has_tda9887:1;
|
||||
/* Many Philips tuners use tda9887 PORT1 to select the FM radio
|
||||
sensitivity. If this setting is 1, then set PORT1 to 1 to
|
||||
get proper FM reception. */
|
||||
unsigned int port1_fm_high_sensitivity:1;
|
||||
/* Some Philips tuners use tda9887 PORT2 to select the FM radio
|
||||
sensitivity. If this setting is 1, then set PORT2 to 1 to
|
||||
get proper FM reception. */
|
||||
unsigned int port2_fm_high_sensitivity:1;
|
||||
/* Some Philips tuners use tda9887 cGainNormal to select the FM radio
|
||||
sensitivity. If this setting is 1, e register will use cGainNormal
|
||||
instead of cGainLow. */
|
||||
unsigned int fm_gain_normal:1;
|
||||
/* Most tuners with a tda9887 use QSS mode. Some (cheaper) tuners
|
||||
use Intercarrier mode. If this setting is 1, then the tuner
|
||||
needs to be set to intercarrier mode. */
|
||||
unsigned int intercarrier_mode:1;
|
||||
/* This setting sets the default value for PORT1.
|
||||
0 means inactive, 1 means active. Note: the actual bit
|
||||
value written to the tda9887 is inverted. So a 0 here
|
||||
means a 1 in the B6 bit. */
|
||||
unsigned int port1_active:1;
|
||||
/* This setting sets the default value for PORT2.
|
||||
0 means inactive, 1 means active. Note: the actual bit
|
||||
value written to the tda9887 is inverted. So a 0 here
|
||||
means a 1 in the B7 bit. */
|
||||
unsigned int port2_active:1;
|
||||
/* Sometimes PORT1 is inverted when the SECAM-L' standard is selected.
|
||||
Set this bit to 1 if this is needed. */
|
||||
unsigned int port1_invert_for_secam_lc:1;
|
||||
/* Sometimes PORT2 is inverted when the SECAM-L' standard is selected.
|
||||
Set this bit to 1 if this is needed. */
|
||||
unsigned int port2_invert_for_secam_lc:1;
|
||||
/* Some cards require PORT1 to be 1 for mono Radio FM and 0 for stereo. */
|
||||
unsigned int port1_set_for_fm_mono:1;
|
||||
/* Select 18% (or according to datasheet 0%) L standard PLL gating,
|
||||
vs the driver default of 36%. */
|
||||
unsigned int default_pll_gating_18:1;
|
||||
/* IF to use in radio mode. Tuners with a separate radio IF filter
|
||||
seem to use 10.7, while those without use 33.3 for PAL/SECAM tuners
|
||||
and 41.3 for NTSC tuners. 0 = 10.7, 1 = 33.3, 2 = 41.3 */
|
||||
unsigned int radio_if:2;
|
||||
/* Default tda9887 TOP value in dB for the low band. Default is 0.
|
||||
Range: -16:+15 */
|
||||
signed int default_top_low:5;
|
||||
/* Default tda9887 TOP value in dB for the mid band. Default is 0.
|
||||
Range: -16:+15 */
|
||||
signed int default_top_mid:5;
|
||||
/* Default tda9887 TOP value in dB for the high band. Default is 0.
|
||||
Range: -16:+15 */
|
||||
signed int default_top_high:5;
|
||||
/* Default tda9887 TOP value in dB for SECAM-L/L' for the low band.
|
||||
Default is 0. Several tuners require a different TOP value for
|
||||
the SECAM-L/L' standards. Range: -16:+15 */
|
||||
signed int default_top_secam_low:5;
|
||||
/* Default tda9887 TOP value in dB for SECAM-L/L' for the mid band.
|
||||
Default is 0. Several tuners require a different TOP value for
|
||||
the SECAM-L/L' standards. Range: -16:+15 */
|
||||
signed int default_top_secam_mid:5;
|
||||
/* Default tda9887 TOP value in dB for SECAM-L/L' for the high band.
|
||||
Default is 0. Several tuners require a different TOP value for
|
||||
the SECAM-L/L' standards. Range: -16:+15 */
|
||||
signed int default_top_secam_high:5;
|
||||
|
||||
u16 iffreq;
|
||||
|
|
|
|||
Loading…
Reference in New Issue