Merge branch 'writeback-workqueue' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq into for-3.10/core

Tejun writes:

-----

This is the pull request for the earlier patchset[1] with the same
name.  It's only three patches (the first one was committed to
workqueue tree) but the merge strategy is a bit involved due to the
dependencies.

* Because the conversion needs features from wq/for-3.10,
  block/for-3.10/core is based on rc3, and wq/for-3.10 has conflicts
  with rc3, I pulled mainline (rc5) into wq/for-3.10 to prevent those
  workqueue conflicts from flaring up in block tree.

* Resolving the issue that Jan and Dave raised about debugging
  requires arch-wide changes.  The patchset is being worked on[2] but
  it'll have to go through -mm after these changes show up in -next,
  and not included in this pull request.

The three commits are located in the following git branch.

  git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git writeback-workqueue

Pulling it into block/for-3.10/core produces a conflict in
drivers/md/raid5.c between the following two commits.

  e3620a3ad5 ("MD RAID5: Avoid accessing gendisk or queue structs when not available")
  2f6db2a707 ("raid5: use bio_reset()")

The conflict is trivial - one removes an "if ()" conditional while the
other removes "rbi->bi_next = NULL" right above it.  We just need to
remove both.  The merged branch is available at

  git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git block-test-merge

so that you can use it for verification.  The test merge commit has
proper merge description.

While these changes are a bit of pain to route, they make code simpler
and even have, while minute, measureable performance gain[3] even on a
workload which isn't particularly favorable to showing the benefits of
this conversion.

----

Fixed up the conflict.

Conflicts:
	drivers/md/raid5.c

Signed-off-by: Jens Axboe <axboe@kernel.dk>

CREDITS

@@ -1510,6 +1510,14 @@ D: Natsemi ethernet
 D: Cobalt Networks (x86) support
 D: This-and-That
 
+N: Mark M. Hoffman
+E: mhoffman@lightlink.com
+D: asb100, lm93 and smsc47b397 hardware monitoring drivers
+D: hwmon subsystem core
+D: hwmon subsystem maintainer
+D: i2c-sis96x and i2c-stub SMBus drivers
+S: USA
+
 N: Dirk Hohndel
 E: hohndel@suse.de
 D: The XFree86[tm] Project

Documentation/hwmon/lm75

@@ -23,7 +23,7 @@ Supported chips:
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/
   * Microchip (TelCom) TCN75
-    Prefix: 'lm75'
+    Prefix: 'tcn75'
     Addresses scanned: none
     Datasheet: Publicly available at the Microchip website
                http://www.microchip.com/

Documentation/i2c/busses/i2c-diolan-u2c

@@ -5,7 +5,7 @@ Supported adapters:
     Documentation:
 	http://www.diolan.com/i2c/u2c12.html
 
-Author: Guenter Roeck <guenter.roeck@ericsson.com>
+Author: Guenter Roeck <linux@roeck-us.net>
 
 Description
 -----------

Documentation/kernel-parameters.txt

@@ -3222,6 +3222,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			or other driver-specific files in the
 			Documentation/watchdog/ directory.
 
+	workqueue.disable_numa
+			By default, all work items queued to unbound
+			workqueues are affine to the NUMA nodes they're
+			issued on, which results in better behavior in
+			general.  If NUMA affinity needs to be disabled for
+			whatever reason, this option can be used.  Note
+			that this also can be controlled per-workqueue for
+			workqueues visible under /sys/bus/workqueue/.
+
 	x2apic_phys	[X86-64,APIC] Use x2apic physical mode instead of
 			default x2apic cluster mode on platforms
 			supporting x2apic.

Documentation/networking/ipvs-sysctl.txt

@@ -15,6 +15,13 @@ amemthresh - INTEGER
         enabled and the variable is automatically set to 2, otherwise
         the strategy is disabled and the variable is  set  to 1.
 
+backup_only - BOOLEAN
+	0 - disabled (default)
+	not 0 - enabled
+
+	If set, disable the director function while the server is
+	in backup mode to avoid packet loops for DR/TUN methods.
+
 conntrack - BOOLEAN
 	0 - disabled (default)
 	not 0 - enabled

Documentation/sound/alsa/ALSA-Configuration.txt

@@ -912,7 +912,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
     models depending on the codec chip.  The list of available models
     is found in HD-Audio-Models.txt
 
-    The model name "genric" is treated as a special case.  When this
+    The model name "generic" is treated as a special case.  When this
     model is given, the driver uses the generic codec parser without
     "codec-patch".  It's sometimes good for testing and debugging.
 

Documentation/sound/alsa/seq_oss.html

@@ -285,7 +285,7 @@ sample data.
 <H4>
 7.2.4 Close Callback</H4>
 The <TT>close</TT> callback is called when this device is closed by the
-applicaion. If any private data was allocated in open callback, it must
+application. If any private data was allocated in open callback, it must
 be released in the close callback. The deletion of ALSA port should be
 done here, too. This callback must not be NULL.
 <H4>

MAINTAINERS

@@ -1338,12 +1338,6 @@ S:	Maintained
 F:	drivers/platform/x86/asus*.c
 F:	drivers/platform/x86/eeepc*.c
 
-ASUS ASB100 HARDWARE MONITOR DRIVER
-M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
-L:	lm-sensors@lm-sensors.org
-S:	Maintained
-F:	drivers/hwmon/asb100.c
-
 ASYNCHRONOUS TRANSFERS/TRANSFORMS (IOAT) API
 M:	Dan Williams <djbw@fb.com>
 W:	http://sourceforge.net/projects/xscaleiop
@@ -1467,6 +1461,12 @@ F:	drivers/dma/at_hdmac.c
 F:	drivers/dma/at_hdmac_regs.h
 F:	include/linux/platform_data/dma-atmel.h
 
+ATMEL I2C DRIVER
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
+L:	linux-i2c@vger.kernel.org
+S:	Supported
+F:	drivers/i2c/busses/i2c-at91.c
+
 ATMEL ISI DRIVER
 M:	Josh Wu <josh.wu@atmel.com>
 L:	linux-media@vger.kernel.org
@@ -2629,7 +2629,7 @@ F:	include/uapi/drm/
 
 INTEL DRM DRIVERS (excluding Poulsbo, Moorestown and derivative chipsets)
 M:	Daniel Vetter <daniel.vetter@ffwll.ch>
-L:	intel-gfx@lists.freedesktop.org (subscribers-only)
+L:	intel-gfx@lists.freedesktop.org
 L:	dri-devel@lists.freedesktop.org
 T:	git git://people.freedesktop.org/~danvet/drm-intel
 S:	Supported
@@ -3242,6 +3242,12 @@ F:	Documentation/firmware_class/
 F:	drivers/base/firmware*.c
 F:	include/linux/firmware.h
 
+FLASHSYSTEM DRIVER (IBM FlashSystem 70/80 PCI SSD Flash Card)
+M:	Joshua Morris <josh.h.morris@us.ibm.com>
+M:	Philip Kelleher <pjk1939@linux.vnet.ibm.com>
+S:	Maintained
+F:	drivers/block/rsxx/
+
 FLOPPY DRIVER
 M:	Jiri Kosina <jkosina@suse.cz>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/floppy.git
@@ -3851,7 +3857,7 @@ F:	drivers/i2c/busses/i2c-ismt.c
 F:	Documentation/i2c/busses/i2c-ismt
 
 I2C/SMBUS STUB DRIVER
-M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
+M:	Jean Delvare <khali@linux-fr.org>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/i2c-stub.c
@@ -5647,6 +5653,14 @@ S:	Maintained
 F:	drivers/video/riva/
 F:	drivers/video/nvidia/
 
+NVM EXPRESS DRIVER
+M:	Matthew Wilcox <willy@linux.intel.com>
+L:	linux-nvme@lists.infradead.org
+T:	git git://git.infradead.org/users/willy/linux-nvme.git
+S:	Supported
+F:	drivers/block/nvme.c
+F:	include/linux/nvme.h
+
 OMAP SUPPORT
 M:	Tony Lindgren <tony@atomide.com>
 L:	linux-omap@vger.kernel.org
@@ -5675,7 +5689,7 @@ S:	Maintained
 F:	arch/arm/*omap*/*clock*
 
 OMAP POWER MANAGEMENT SUPPORT
-M:	Kevin Hilman <khilman@ti.com>
+M:	Kevin Hilman <khilman@deeprootsystems.com>
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	arch/arm/*omap*/*pm*
@@ -5769,7 +5783,7 @@ F:	arch/arm/*omap*/usb*
 
 OMAP GPIO DRIVER
 M:	Santosh Shilimkar <santosh.shilimkar@ti.com>
-M:	Kevin Hilman <khilman@ti.com>
+M:	Kevin Hilman <khilman@deeprootsystems.com>
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	drivers/gpio/gpio-omap.c
@@ -6201,7 +6215,7 @@ F:	include/linux/power_supply.h
 F:	drivers/power/
 
 PNP SUPPORT
-M:	Adam Belay <abelay@mit.edu>
+M:	Rafael J. Wysocki <rafael.j.wysocki@intel.com>
 M:	Bjorn Helgaas <bhelgaas@google.com>
 S:	Maintained
 F:	drivers/pnp/
@@ -6543,12 +6557,6 @@ S:	Maintained
 F:	Documentation/blockdev/ramdisk.txt
 F:	drivers/block/brd.c
 
-RAMSAM DRIVER (IBM RamSan 70/80 PCI SSD Flash Card)
-M:	Joshua Morris <josh.h.morris@us.ibm.com>
-M:	Philip Kelleher <pjk1939@linux.vnet.ibm.com>
-S:	Maintained
-F:	drivers/block/rsxx/
-
 RANDOM NUMBER DRIVER
 M:	Theodore Ts'o" <tytso@mit.edu>
 S:	Maintained
@@ -7165,7 +7173,7 @@ F:	arch/arm/mach-s3c2410/bast-irq.c
 
 TI DAVINCI MACHINE SUPPORT
 M:	Sekhar Nori <nsekhar@ti.com>
-M:	Kevin Hilman <khilman@ti.com>
+M:	Kevin Hilman <khilman@deeprootsystems.com>
 L:	davinci-linux-open-source@linux.davincidsp.com (moderated for non-subscribers)
 T:	git git://gitorious.org/linux-davinci/linux-davinci.git
 Q:	http://patchwork.kernel.org/project/linux-davinci/list/
@@ -7198,13 +7206,6 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ethernet/sis/sis900.*
 
-SIS 96X I2C/SMBUS DRIVER
-M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
-L:	linux-i2c@vger.kernel.org
-S:	Maintained
-F:	Documentation/i2c/busses/i2c-sis96x
-F:	drivers/i2c/busses/i2c-sis96x.c
-
 SIS FRAMEBUFFER DRIVER
 M:	Thomas Winischhofer <thomas@winischhofer.net>
 W:	http://www.winischhofer.net/linuxsisvga.shtml
@@ -7282,7 +7283,7 @@ F:	Documentation/hwmon/sch5627
 F:	drivers/hwmon/sch5627.c
 
 SMSC47B397 HARDWARE MONITOR DRIVER
-M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
+M:	Jean Delvare <khali@linux-fr.org>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/smsc47b397
@@ -7705,9 +7706,10 @@ F:	include/linux/swiotlb.h
 
 SYNOPSYS ARC ARCHITECTURE
 M:	Vineet Gupta <vgupta@synopsys.com>
-L:	linux-snps-arc@vger.kernel.org
 S:	Supported
 F:	arch/arc/
+F:	Documentation/devicetree/bindings/arc/
+F:	drivers/tty/serial/arc-uart.c
 
 SYSV FILESYSTEM
 M:	Christoph Hellwig <hch@infradead.org>

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 9
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc5
 NAME = Unicycling Gorilla
 
 # *DOCUMENTATION*

arch/arc/include/asm/dma-mapping.h

@@ -126,7 +126,7 @@ dma_map_sg(struct device *dev, struct scatterlist *sg,
 	int i;
 
 	for_each_sg(sg, s, nents, i)
-		sg->dma_address = dma_map_page(dev, sg_page(s), s->offset,
+		s->dma_address = dma_map_page(dev, sg_page(s), s->offset,
 					       s->length, dir);
 
 	return nents;

arch/arc/include/asm/elf.h

@@ -72,7 +72,4 @@ extern int elf_check_arch(const struct elf32_hdr *);
  */
 #define ELF_PLATFORM	(NULL)
 
-#define SET_PERSONALITY(ex) \
-	set_personality(PER_LINUX | (current->personality & (~PER_MASK)))
-
 #endif

arch/arc/include/asm/entry.h

@@ -415,7 +415,7 @@
  *-------------------------------------------------------------*/
 .macro SAVE_ALL_EXCEPTION   marker
 
-	st      \marker, [sp, 8]
+	st      \marker, [sp, 8]	/* orig_r8 */
 	st      r0, [sp, 4]    /* orig_r0, needed only for sys calls */
 
 	/* Restore r9 used to code the early prologue */

arch/arc/include/asm/kgdb.h

@@ -13,7 +13,7 @@
 
 #ifdef CONFIG_KGDB
 
-#include <asm/user.h>
+#include <asm/ptrace.h>
 
 /* to ensure compatibility with Linux 2.6.35, we don't implement the get/set
  * register API yet */
@@ -53,9 +53,7 @@ enum arc700_linux_regnums {
 };
 
 #else
-static inline void kgdb_trap(struct pt_regs *regs, int param)
+#define kgdb_trap(regs, param)
-{
-}
 #endif
 
 #endif	/* __ARC_KGDB_H__ */

arch/arc/include/asm/ptrace.h

@@ -123,7 +123,7 @@ static inline long regs_return_value(struct pt_regs *regs)
 #define orig_r8_IS_SCALL		0x0001
 #define orig_r8_IS_SCALL_RESTARTED	0x0002
 #define orig_r8_IS_BRKPT		0x0004
-#define orig_r8_IS_EXCPN		0x0004
+#define orig_r8_IS_EXCPN		0x0008
 #define orig_r8_IS_IRQ1			0x0010
 #define orig_r8_IS_IRQ2			0x0020
 

arch/arc/include/asm/syscalls.h

@@ -16,8 +16,6 @@
 #include <linux/types.h>
 
 int sys_clone_wrapper(int, int, int, int, int);
-int sys_fork_wrapper(void);
-int sys_vfork_wrapper(void);
 int sys_cacheflush(uint32_t, uint32_t uint32_t);
 int sys_arc_settls(void *);
 int sys_arc_gettls(void);

arch/arc/include/uapi/asm/ptrace.h

@@ -28,14 +28,14 @@
 */
 struct user_regs_struct {
 
-	struct scratch {
+	struct {
 		long pad;
 		long bta, lp_start, lp_end, lp_count;
 		long status32, ret, blink, fp, gp;
 		long r12, r11, r10, r9, r8, r7, r6, r5, r4, r3, r2, r1, r0;
 		long sp;
 	} scratch;
-	struct callee {
+	struct {
 		long pad;
 		long r25, r24, r23, r22, r21, r20;
 		long r19, r18, r17, r16, r15, r14, r13;

arch/arc/kernel/entry.S

@@ -452,7 +452,7 @@ tracesys:
 	; using ERET won't work since next-PC has already committed
 	lr  r12, [efa]
 	GET_CURR_TASK_FIELD_PTR   TASK_THREAD, r11
-	st  r12, [r11, THREAD_FAULT_ADDR]
+	st  r12, [r11, THREAD_FAULT_ADDR]	; thread.fault_address
 
 	; PRE Sys Call Ptrace hook
 	mov r0, sp			; pt_regs needed
@@ -792,31 +792,6 @@ ARC_EXIT ret_from_fork
 
 ;################### Special Sys Call Wrappers ##########################
 
-; TBD: call do_fork directly from here
-ARC_ENTRY sys_fork_wrapper
-	SAVE_CALLEE_SAVED_USER
-	bl  @sys_fork
-	DISCARD_CALLEE_SAVED_USER
-
-	GET_CURR_THR_INFO_FLAGS   r10
-	btst r10, TIF_SYSCALL_TRACE
-	bnz  tracesys_exit
-
-	b ret_from_system_call
-ARC_EXIT sys_fork_wrapper
-
-ARC_ENTRY sys_vfork_wrapper
-	SAVE_CALLEE_SAVED_USER
-	bl  @sys_vfork
-	DISCARD_CALLEE_SAVED_USER
-
-	GET_CURR_THR_INFO_FLAGS   r10
-	btst r10, TIF_SYSCALL_TRACE
-	bnz  tracesys_exit
-
-	b ret_from_system_call
-ARC_EXIT sys_vfork_wrapper
-
 ARC_ENTRY sys_clone_wrapper
 	SAVE_CALLEE_SAVED_USER
 	bl  @sys_clone

arch/arc/kernel/kgdb.c

@@ -9,6 +9,7 @@
  */
 
 #include <linux/kgdb.h>
+#include <linux/sched.h>
 #include <asm/disasm.h>
 #include <asm/cacheflush.h>
 

arch/arc/kernel/setup.c

@@ -232,10 +232,8 @@ char *arc_extn_mumbojumbo(int cpu_id, char *buf, int len)
 
 	n += scnprintf(buf + n, len - n, "\n");
 
-#ifdef _ASM_GENERIC_UNISTD_H
 	n += scnprintf(buf + n, len - n,
-		       "OS ABI [v2]\t: asm-generic/{unistd,stat,fcntl}\n");
+		       "OS ABI [v3]\t: no-legacy-syscalls\n");
-#endif
 
 	return buf;
 }

arch/arc/kernel/sys.c

@@ -6,8 +6,6 @@
 #include <asm/syscalls.h>
 
 #define sys_clone	sys_clone_wrapper
-#define sys_fork	sys_fork_wrapper
-#define sys_vfork	sys_vfork_wrapper
 
 #undef __SYSCALL
 #define __SYSCALL(nr, call) [nr] = (call),

arch/arm/Kconfig

@@ -49,7 +49,6 @@ config ARM
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_UID16
-	select VIRT_TO_BUS
 	select KTIME_SCALAR
 	select PERF_USE_VMALLOC
 	select RTC_LIB
@@ -743,6 +742,7 @@ config ARCH_RPC
 	select NEED_MACH_IO_H
 	select NEED_MACH_MEMORY_H
 	select NO_IOPORT
+	select VIRT_TO_BUS
 	help
 	  On the Acorn Risc-PC, Linux can support the internal IDE disk and
 	  CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -878,6 +878,7 @@ config ARCH_SHARK
 	select ISA_DMA
 	select NEED_MACH_MEMORY_H
 	select PCI
+	select VIRT_TO_BUS
 	select ZONE_DMA
 	help
 	  Support for the StrongARM based Digital DNARD machine, also known
@@ -1005,12 +1006,12 @@ config ARCH_MULTI_V4_V5
 	bool
 
 config ARCH_MULTI_V6
-	bool "ARMv6 based platforms (ARM11, Scorpion, ...)"
+	bool "ARMv6 based platforms (ARM11)"
 	select ARCH_MULTI_V6_V7
 	select CPU_V6
 
 config ARCH_MULTI_V7
-	bool "ARMv7 based platforms (Cortex-A, PJ4, Krait)"
+	bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
 	default y
 	select ARCH_MULTI_V6_V7
 	select ARCH_VEXPRESS
@@ -1461,10 +1462,6 @@ config ISA_DMA
 	bool
 	select ISA_DMA_API
 
-config ARCH_NO_VIRT_TO_BUS
-	def_bool y
-	depends on !ARCH_RPC && !ARCH_NETWINDER && !ARCH_SHARK
-
 # Select ISA DMA interface
 config ISA_DMA_API
 	bool

arch/arm/Kconfig.debug

@@ -495,6 +495,7 @@ config DEBUG_IMX_UART_PORT
 						DEBUG_IMX53_UART || \
 						DEBUG_IMX6Q_UART
 	default 1
+	depends on ARCH_MXC
 	help
 	  Choose UART port on which kernel low-level debug messages
 	  should be output.

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -238,8 +238,32 @@
 				nand {
 					pinctrl_nand: nand-0 {
 						atmel,pins =
-							<3 4 0x0 0x1	/* PD5 gpio RDY pin pull_up */
+							<3 0 0x1 0x0	/* PD0 periph A Read Enable */
-							 3 5 0x0 0x1>;	/* PD4 gpio enable pin pull_up */
+							 3 1 0x1 0x0	/* PD1 periph A Write Enable */
+							 3 2 0x1 0x0	/* PD2 periph A Address Latch Enable */
+							 3 3 0x1 0x0	/* PD3 periph A Command Latch Enable */
+							 3 4 0x0 0x1	/* PD4 gpio Chip Enable pin pull_up */
+							 3 5 0x0 0x1	/* PD5 gpio RDY/BUSY pin pull_up */
+							 3 6 0x1 0x0	/* PD6 periph A Data bit 0 */
+							 3 7 0x1 0x0	/* PD7 periph A Data bit 1 */
+							 3 8 0x1 0x0	/* PD8 periph A Data bit 2 */
+							 3 9 0x1 0x0	/* PD9 periph A Data bit 3 */
+							 3 10 0x1 0x0	/* PD10 periph A Data bit 4 */
+							 3 11 0x1 0x0	/* PD11 periph A Data bit 5 */
+							 3 12 0x1 0x0	/* PD12 periph A Data bit 6 */
+							 3 13 0x1 0x0>;	/* PD13 periph A Data bit 7 */
+					};
+
+					pinctrl_nand_16bits: nand_16bits-0 {
+						atmel,pins =
+							<3 14 0x1 0x0	/* PD14 periph A Data bit 8 */
+							 3 15 0x1 0x0	/* PD15 periph A Data bit 9 */
+							 3 16 0x1 0x0	/* PD16 periph A Data bit 10 */
+							 3 17 0x1 0x0	/* PD17 periph A Data bit 11 */
+							 3 18 0x1 0x0	/* PD18 periph A Data bit 12 */
+							 3 19 0x1 0x0	/* PD19 periph A Data bit 13 */
+							 3 20 0x1 0x0	/* PD20 periph A Data bit 14 */
+							 3 21 0x1 0x0>;	/* PD21 periph A Data bit 15 */
 					};
 				};
 

arch/arm/boot/dts/exynos4.dtsi

@@ -275,18 +275,27 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12680000 0x1000>;
 			interrupts = <0 35 0>;
+			#dma-cells = <1>;
+			#dma-channels = <8>;
+			#dma-requests = <32>;
 		};
 
 		pdma1: pdma@12690000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12690000 0x1000>;
 			interrupts = <0 36 0>;
+			#dma-cells = <1>;
+			#dma-channels = <8>;
+			#dma-requests = <32>;
 		};
 
 		mdma1: mdma@12850000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12850000 0x1000>;
 			interrupts = <0 34 0>;
+			#dma-cells = <1>;
+			#dma-channels = <8>;
+			#dma-requests = <1>;
 		};
 	};
 };

arch/arm/boot/dts/exynos5440.dtsi

@@ -142,12 +142,18 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x120000 0x1000>;
 			interrupts = <0 34 0>;
+			#dma-cells = <1>;
+			#dma-channels = <8>;
+			#dma-requests = <32>;
 		};
 
 		pdma1: pdma@121B0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121000 0x1000>;
 			interrupts = <0 35 0>;
+			#dma-cells = <1>;
+			#dma-channels = <8>;
+			#dma-requests = <32>;
 		};
 	};
 

arch/arm/boot/dts/tegra20.dtsi

@@ -385,7 +385,7 @@
 
 	spi@7000d800 {
 		compatible = "nvidia,tegra20-slink";
-		reg = <0x7000d480 0x200>;
+		reg = <0x7000d800 0x200>;
 		interrupts = <0 83 0x04>;
 		nvidia,dma-request-selector = <&apbdma 17>;
 		#address-cells = <1>;

arch/arm/boot/dts/tegra30.dtsi

@@ -372,7 +372,7 @@
 
 	spi@7000d800 {
 		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
-		reg = <0x7000d480 0x200>;
+		reg = <0x7000d800 0x200>;
 		interrupts = <0 83 0x04>;
 		nvidia,dma-request-selector = <&apbdma 17>;
 		#address-cells = <1>;

arch/arm/kernel/smp.c

@@ -480,7 +480,7 @@ static void __cpuinit broadcast_timer_setup(struct clock_event_device *evt)
 	evt->features	= CLOCK_EVT_FEAT_ONESHOT |
 			  CLOCK_EVT_FEAT_PERIODIC |
 			  CLOCK_EVT_FEAT_DUMMY;
-	evt->rating	= 400;
+	evt->rating	= 100;
 	evt->mult	= 1;
 	evt->set_mode	= broadcast_timer_set_mode;
 

arch/arm/lib/memset.S

@@ -14,31 +14,15 @@
 
 	.text
 	.align	5
-	.word	0
-
-1:	subs	r2, r2, #4		@ 1 do we have enough
-	blt	5f			@ 1 bytes to align with?
-	cmp	r3, #2			@ 1
-	strltb	r1, [ip], #1		@ 1
-	strleb	r1, [ip], #1		@ 1
-	strb	r1, [ip], #1		@ 1
-	add	r2, r2, r3		@ 1 (r2 = r2 - (4 - r3))
-/*
- * The pointer is now aligned and the length is adjusted.  Try doing the
- * memset again.
- */
 
 ENTRY(memset)
-/*
+	ands	r3, r0, #3		@ 1 unaligned?
- * Preserve the contents of r0 for the return value.
+	mov	ip, r0			@ preserve r0 as return value
- */
+	bne	6f			@ 1
-	mov	ip, r0
-	ands	r3, ip, #3		@ 1 unaligned?
-	bne	1b			@ 1
 /*
  * we know that the pointer in ip is aligned to a word boundary.
  */
-	orr	r1, r1, r1, lsl #8
+1:	orr	r1, r1, r1, lsl #8
 	orr	r1, r1, r1, lsl #16
 	mov	r3, r1
 	cmp	r2, #16
@@ -127,4 +111,13 @@ ENTRY(memset)
 	tst	r2, #1
 	strneb	r1, [ip], #1
 	mov	pc, lr
+
+6:	subs	r2, r2, #4		@ 1 do we have enough
+	blt	5b			@ 1 bytes to align with?
+	cmp	r3, #2			@ 1
+	strltb	r1, [ip], #1		@ 1
+	strleb	r1, [ip], #1		@ 1
+	strb	r1, [ip], #1		@ 1
+	add	r2, r2, r3		@ 1 (r2 = r2 - (4 - r3))
+	b	1b
 ENDPROC(memset)

arch/arm/mach-at91/include/mach/gpio.h

@@ -209,6 +209,14 @@ extern int at91_get_gpio_value(unsigned pin);
 extern void at91_gpio_suspend(void);
 extern void at91_gpio_resume(void);
 
+#ifdef CONFIG_PINCTRL_AT91
+extern void at91_pinctrl_gpio_suspend(void);
+extern void at91_pinctrl_gpio_resume(void);
+#else
+static inline void at91_pinctrl_gpio_suspend(void) {}
+static inline void at91_pinctrl_gpio_resume(void) {}
+#endif
+
 #endif	/* __ASSEMBLY__ */
 
 #endif

arch/arm/mach-at91/irq.c

@@ -92,23 +92,21 @@ static int at91_aic_set_wake(struct irq_data *d, unsigned value)
 
 void at91_irq_suspend(void)
 {
-	int i = 0, bit;
+	int bit = -1;
 
 	if (has_aic5()) {
 		/* disable enabled irqs */
-		while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) {
+		while ((bit = find_next_bit(backups, n_irqs, bit + 1)) < n_irqs) {
 			at91_aic_write(AT91_AIC5_SSR,
 				       bit & AT91_AIC5_INTSEL_MSK);
 			at91_aic_write(AT91_AIC5_IDCR, 1);
-			i = bit;
 		}
 		/* enable wakeup irqs */
-		i = 0;
+		bit = -1;
-		while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) {
+		while ((bit = find_next_bit(wakeups, n_irqs, bit + 1)) < n_irqs) {
 			at91_aic_write(AT91_AIC5_SSR,
 				       bit & AT91_AIC5_INTSEL_MSK);
 			at91_aic_write(AT91_AIC5_IECR, 1);
-			i = bit;
 		}
 	} else {
 		at91_aic_write(AT91_AIC_IDCR, *backups);
@@ -118,23 +116,21 @@ void at91_irq_suspend(void)
 
 void at91_irq_resume(void)
 {
-	int i = 0, bit;
+	int bit = -1;
 
 	if (has_aic5()) {
 		/* disable wakeup irqs */
-		while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) {
+		while ((bit = find_next_bit(wakeups, n_irqs, bit + 1)) < n_irqs) {
 			at91_aic_write(AT91_AIC5_SSR,
 				       bit & AT91_AIC5_INTSEL_MSK);
 			at91_aic_write(AT91_AIC5_IDCR, 1);
-			i = bit;
 		}
 		/* enable irqs disabled for suspend */
-		i = 0;
+		bit = -1;
-		while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) {
+		while ((bit = find_next_bit(backups, n_irqs, bit + 1)) < n_irqs) {
 			at91_aic_write(AT91_AIC5_SSR,
 				       bit & AT91_AIC5_INTSEL_MSK);
 			at91_aic_write(AT91_AIC5_IECR, 1);
-			i = bit;
 		}
 	} else {
 		at91_aic_write(AT91_AIC_IDCR, *wakeups);

arch/arm/mach-at91/pm.c

@@ -201,7 +201,10 @@ extern u32 at91_slow_clock_sz;
 
 static int at91_pm_enter(suspend_state_t state)
 {
-	at91_gpio_suspend();
+	if (of_have_populated_dt())
+		at91_pinctrl_gpio_suspend();
+	else
+		at91_gpio_suspend();
 	at91_irq_suspend();
 
 	pr_debug("AT91: PM - wake mask %08x, pm state %d\n",
@@ -286,7 +289,10 @@ static int at91_pm_enter(suspend_state_t state)
 error:
 	target_state = PM_SUSPEND_ON;
 	at91_irq_resume();
-	at91_gpio_resume();
+	if (of_have_populated_dt())
+		at91_pinctrl_gpio_resume();
+	else
+		at91_gpio_resume();
 	return 0;
 }
 

arch/arm/mach-davinci/dma.c

@@ -743,6 +743,9 @@ EXPORT_SYMBOL(edma_free_channel);
  */
 int edma_alloc_slot(unsigned ctlr, int slot)
 {
+	if (!edma_cc[ctlr])
+		return -EINVAL;
+
 	if (slot >= 0)
 		slot = EDMA_CHAN_SLOT(slot);
 

arch/arm/mach-footbridge/Kconfig

@@ -67,6 +67,7 @@ config ARCH_NETWINDER
 	select ISA
 	select ISA_DMA
 	select PCI
+	select VIRT_TO_BUS
 	help
 	  Say Y here if you intend to run this kernel on the Rebel.COM
 	  NetWinder.  Information about this machine can be found at:

arch/arm/mach-imx/clk-imx35.c

@@ -264,6 +264,7 @@ int __init mx35_clocks_init(void)
 	clk_prepare_enable(clk[gpio3_gate]);
 	clk_prepare_enable(clk[iim_gate]);
 	clk_prepare_enable(clk[emi_gate]);
+	clk_prepare_enable(clk[max_gate]);
 
 	/*
 	 * SCC is needed to boot via mmc after a watchdog reset. The clock code

arch/arm/mach-imx/imx25-dt.c

@@ -27,6 +27,11 @@ static const char * const imx25_dt_board_compat[] __initconst = {
 	NULL
 };
 
+static void __init imx25_timer_init(void)
+{
+	mx25_clocks_init_dt();
+}
+
 DT_MACHINE_START(IMX25_DT, "Freescale i.MX25 (Device Tree Support)")
 	.map_io		= mx25_map_io,
 	.init_early	= imx25_init_early,

arch/arm/mach-mmp/gplugd.c

@@ -9,6 +9,7 @@
  */
 
 #include <linux/init.h>
+#include <linux/platform_device.h>
 #include <linux/gpio.h>
 
 #include <asm/mach/arch.h>

arch/arm/mach-mxs/mach-mxs.c

@@ -41,8 +41,6 @@ static struct fb_videomode mx23evk_video_modes[] = {
 		.lower_margin	= 4,
 		.hsync_len	= 1,
 		.vsync_len	= 1,
-		.sync		= FB_SYNC_DATA_ENABLE_HIGH_ACT |
-				  FB_SYNC_DOTCLK_FAILING_ACT,
 	},
 };
 
@@ -59,8 +57,6 @@ static struct fb_videomode mx28evk_video_modes[] = {
 		.lower_margin	= 10,
 		.hsync_len	= 10,
 		.vsync_len	= 10,
-		.sync		= FB_SYNC_DATA_ENABLE_HIGH_ACT |
-				  FB_SYNC_DOTCLK_FAILING_ACT,
 	},
 };
 
@@ -77,7 +73,6 @@ static struct fb_videomode m28evk_video_modes[] = {
 		.lower_margin	= 45,
 		.hsync_len	= 1,
 		.vsync_len	= 1,
-		.sync		= FB_SYNC_DATA_ENABLE_HIGH_ACT,
 	},
 };
 
@@ -94,9 +89,7 @@ static struct fb_videomode apx4devkit_video_modes[] = {
 		.lower_margin	= 13,
 		.hsync_len	= 48,
 		.vsync_len	= 3,
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT |
+		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-				  FB_SYNC_DATA_ENABLE_HIGH_ACT |
-				  FB_SYNC_DOTCLK_FAILING_ACT,
 	},
 };
 
@@ -113,9 +106,7 @@ static struct fb_videomode apf28dev_video_modes[] = {
 		.lower_margin = 0x15,
 		.hsync_len = 64,
 		.vsync_len = 4,
-		.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT |
+		.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-				FB_SYNC_DATA_ENABLE_HIGH_ACT |
-				FB_SYNC_DOTCLK_FAILING_ACT,
 	},
 };
 
@@ -132,7 +123,6 @@ static struct fb_videomode cfa10049_video_modes[] = {
 		.lower_margin	= 2,
 		.hsync_len	= 15,
 		.vsync_len	= 15,
-		.sync		= FB_SYNC_DATA_ENABLE_HIGH_ACT
 	},
 };
 
@@ -259,6 +249,8 @@ static void __init imx23_evk_init(void)
 	mxsfb_pdata.mode_count = ARRAY_SIZE(mx23evk_video_modes);
 	mxsfb_pdata.default_bpp = 32;
 	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
+	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
+				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 }
 
 static inline void enable_clk_enet_out(void)
@@ -278,6 +270,8 @@ static void __init imx28_evk_init(void)
 	mxsfb_pdata.mode_count = ARRAY_SIZE(mx28evk_video_modes);
 	mxsfb_pdata.default_bpp = 32;
 	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
+	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
+				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 
 	mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
 }
@@ -297,6 +291,7 @@ static void __init m28evk_init(void)
 	mxsfb_pdata.mode_count = ARRAY_SIZE(m28evk_video_modes);
 	mxsfb_pdata.default_bpp = 16;
 	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
+	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
 }
 
 static void __init sc_sps1_init(void)
@@ -322,6 +317,8 @@ static void __init apx4devkit_init(void)
 	mxsfb_pdata.mode_count = ARRAY_SIZE(apx4devkit_video_modes);
 	mxsfb_pdata.default_bpp = 32;
 	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
+	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
+				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 }
 
 #define ENET0_MDC__GPIO_4_0	MXS_GPIO_NR(4, 0)
@@ -407,6 +404,7 @@ static void __init cfa10049_init(void)
 	mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
 	mxsfb_pdata.default_bpp = 32;
 	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
+	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
 }
 
 static void __init cfa10037_init(void)
@@ -423,6 +421,8 @@ static void __init apf28_init(void)
 	mxsfb_pdata.mode_count = ARRAY_SIZE(apf28dev_video_modes);
 	mxsfb_pdata.default_bpp = 16;
 	mxsfb_pdata.ld_intf_width = STMLCDIF_16BIT;
+	mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
+				MXSFB_SYNC_DOTCLK_FAILING_ACT;
 }
 
 static void __init mxs_machine_init(void)

arch/arm/mach-s5pv210/clock.c

@@ -214,11 +214,6 @@ static struct clk clk_pcmcdclk2 = {
 	.name		= "pcmcdclk",
 };
 
-static struct clk dummy_apb_pclk = {
-	.name		= "apb_pclk",
-	.id		= -1,
-};
-
 static struct clk *clkset_vpllsrc_list[] = {
 	[0] = &clk_fin_vpll,
 	[1] = &clk_sclk_hdmi27m,
@@ -305,18 +300,6 @@ static struct clk_ops clk_fout_apll_ops = {
 
 static struct clk init_clocks_off[] = {
 	{
-		.name		= "dma",
-		.devname	= "dma-pl330.0",
-		.parent		= &clk_hclk_psys.clk,
-		.enable		= s5pv210_clk_ip0_ctrl,
-		.ctrlbit	= (1 << 3),
-	}, {
-		.name		= "dma",
-		.devname	= "dma-pl330.1",
-		.parent		= &clk_hclk_psys.clk,
-		.enable		= s5pv210_clk_ip0_ctrl,
-		.ctrlbit	= (1 << 4),
-	}, {
 		.name		= "rot",
 		.parent		= &clk_hclk_dsys.clk,
 		.enable		= s5pv210_clk_ip0_ctrl,
@@ -573,6 +556,20 @@ static struct clk clk_hsmmc3 = {
 	.ctrlbit	= (1<<19),
 };
 
+static struct clk clk_pdma0 = {
+	.name		= "pdma0",
+	.parent		= &clk_hclk_psys.clk,
+	.enable		= s5pv210_clk_ip0_ctrl,
+	.ctrlbit	= (1 << 3),
+};
+
+static struct clk clk_pdma1 = {
+	.name		= "pdma1",
+	.parent		= &clk_hclk_psys.clk,
+	.enable		= s5pv210_clk_ip0_ctrl,
+	.ctrlbit	= (1 << 4),
+};
+
 static struct clk *clkset_uart_list[] = {
 	[6] = &clk_mout_mpll.clk,
 	[7] = &clk_mout_epll.clk,
@@ -1075,6 +1072,8 @@ static struct clk *clk_cdev[] = {
 	&clk_hsmmc1,
 	&clk_hsmmc2,
 	&clk_hsmmc3,
+	&clk_pdma0,
+	&clk_pdma1,
 };
 
 /* Clock initialisation code */
@@ -1333,6 +1332,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
 	CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
 	CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("dma-pl330.0", "apb_pclk", &clk_pdma0),
+	CLKDEV_INIT("dma-pl330.1", "apb_pclk", &clk_pdma1),
 };
 
 void __init s5pv210_register_clocks(void)
@@ -1361,6 +1362,5 @@ void __init s5pv210_register_clocks(void)
 	for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++)
 		s3c_disable_clocks(clk_cdev[ptr], 1);
 
-	s3c24xx_register_clock(&dummy_apb_pclk);
 	s3c_pwmclk_init();
 }

arch/arm/mach-s5pv210/mach-goni.c

@@ -845,7 +845,7 @@ static struct fimc_source_info goni_camera_sensors[] = {
 		.mux_id		= 0,
 		.flags		= V4L2_MBUS_PCLK_SAMPLE_FALLING |
 				  V4L2_MBUS_VSYNC_ACTIVE_LOW,
-		.bus_type	= FIMC_BUS_TYPE_ITU_601,
+		.fimc_bus_type	= FIMC_BUS_TYPE_ITU_601,
 		.board_info	= &noon010pc30_board_info,
 		.i2c_bus_num	= 0,
 		.clk_frequency	= 16000000UL,

arch/arm/mach-shmobile/board-marzen.c

@@ -32,6 +32,7 @@
 #include <linux/smsc911x.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/sh_hspi.h>
+#include <linux/mmc/host.h>
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/mfd/tmio.h>
 #include <linux/usb/otg.h>

arch/arm/net/bpf_jit_32.c

@@ -576,7 +576,7 @@ load_ind:
 			/* x = ((*(frame + k)) & 0xf) << 2; */
 			ctx->seen |= SEEN_X | SEEN_DATA | SEEN_CALL;
 			/* the interpreter should deal with the negative K */
-			if (k < 0)
+			if ((int)k < 0)
 				return -1;
 			/* offset in r1: we might have to take the slow path */
 			emit_mov_i(r_off, k, ctx);

arch/arm64/Kconfig

@@ -9,7 +9,6 @@ config ARM64
 	select CLONE_BACKWARDS
 	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
-	select GENERIC_HARDIRQS_NO_DEPRECATED
 	select GENERIC_IOMAP
 	select GENERIC_IRQ_PROBE
 	select GENERIC_IRQ_SHOW

arch/arm64/Kconfig.debug

@@ -6,17 +6,6 @@ config FRAME_POINTER
 	bool
 	default y
 
-config DEBUG_ERRORS
-	bool "Verbose kernel error messages"
-	depends on DEBUG_KERNEL
-	help
-	  This option controls verbose debugging information which can be
-	  printed when the kernel detects an internal error. This debugging
-	  information is useful to kernel hackers when tracking down problems,
-	  but mostly meaningless to other people. It's safe to say Y unless
-	  you are concerned with the code size or don't want to see these
-	  messages.
-
 config DEBUG_STACK_USAGE
 	bool "Enable stack utilization instrumentation"
 	depends on DEBUG_KERNEL

arch/arm64/configs/defconfig

@@ -82,4 +82,3 @@ CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_INFO=y
 # CONFIG_FTRACE is not set
 CONFIG_ATOMIC64_SELFTEST=y
-CONFIG_DEBUG_ERRORS=y

arch/arm64/include/asm/ucontext.h

@@ -22,7 +22,7 @@ struct ucontext {
 	stack_t		  uc_stack;
 	sigset_t	  uc_sigmask;
 	/* glibc uses a 1024-bit sigset_t */
-	__u8		  __unused[(1024 - sizeof(sigset_t)) / 8];
+	__u8		  __unused[1024 / 8 - sizeof(sigset_t)];
 	/* last for future expansion */
 	struct sigcontext uc_mcontext;
 };

arch/arm64/kernel/arm64ksyms.c

@@ -40,7 +40,9 @@ EXPORT_SYMBOL(__copy_to_user);
 EXPORT_SYMBOL(__clear_user);
 
 	/* bitops */
+#ifdef CONFIG_SMP
 EXPORT_SYMBOL(__atomic_hash);
+#endif
 
 	/* physical memory */
 EXPORT_SYMBOL(memstart_addr);

arch/arm64/kernel/signal32.c

@@ -549,7 +549,6 @@ int compat_setup_rt_frame(int usig, struct k_sigaction *ka, siginfo_t *info,
 			  sigset_t *set, struct pt_regs *regs)
 {
 	struct compat_rt_sigframe __user *frame;
-	compat_stack_t stack;
 	int err = 0;
 
 	frame = compat_get_sigframe(ka, regs, sizeof(*frame));

arch/arm64/mm/mmu.c

@@ -261,7 +261,7 @@ static void __init create_mapping(phys_addr_t phys, unsigned long virt,
 void __iomem * __init early_io_map(phys_addr_t phys, unsigned long virt)
 {
 	unsigned long size, mask;
-	bool page64k = IS_ENABLED(ARM64_64K_PAGES);
+	bool page64k = IS_ENABLED(CONFIG_ARM64_64K_PAGES);
 	pgd_t *pgd;
 	pud_t *pud;
 	pmd_t *pmd;

arch/ia64/kernel/process.c

@@ -291,7 +291,6 @@ cpu_idle (void)
 		}
 
 		if (!need_resched()) {
-			void (*idle)(void);
 #ifdef CONFIG_SMP
 			min_xtp();
 #endif
@@ -299,9 +298,7 @@ cpu_idle (void)
 			if (mark_idle)
 				(*mark_idle)(1);
 
-			if (!idle)
+			default_idle();
-				idle = default_idle;
-			(*idle)();
 			if (mark_idle)
 				(*mark_idle)(0);
 #ifdef CONFIG_SMP

arch/powerpc/Kconfig

@@ -90,6 +90,7 @@ config GENERIC_GPIO
 config PPC
 	bool
 	default y
+	select BINFMT_ELF
 	select OF
 	select OF_EARLY_FLATTREE
 	select HAVE_FTRACE_MCOUNT_RECORD

arch/powerpc/include/asm/mmu-hash64.h

@@ -343,17 +343,16 @@ extern void slb_set_size(u16 size);
 /*
  * VSID allocation (256MB segment)
  *
- * We first generate a 38-bit "proto-VSID".  For kernel addresses this
+ * We first generate a 37-bit "proto-VSID". Proto-VSIDs are generated
- * is equal to the ESID | 1 << 37, for user addresses it is:
+ * from mmu context id and effective segment id of the address.
- *	(context << USER_ESID_BITS) | (esid & ((1U << USER_ESID_BITS) - 1)
  *
- * This splits the proto-VSID into the below range
+ * For user processes max context id is limited to ((1ul << 19) - 5)
- *  0 - (2^(CONTEXT_BITS + USER_ESID_BITS) - 1) : User proto-VSID range
+ * for kernel space, we use the top 4 context ids to map address as below
- *  2^(CONTEXT_BITS + USER_ESID_BITS) - 2^(VSID_BITS) : Kernel proto-VSID range
+ * NOTE: each context only support 64TB now.
- *
+ * 0x7fffc -  [ 0xc000000000000000 - 0xc0003fffffffffff ]
- * We also have CONTEXT_BITS + USER_ESID_BITS = VSID_BITS - 1
+ * 0x7fffd -  [ 0xd000000000000000 - 0xd0003fffffffffff ]
- * That is, we assign half of the space to user processes and half
+ * 0x7fffe -  [ 0xe000000000000000 - 0xe0003fffffffffff ]
- * to the kernel.
+ * 0x7ffff -  [ 0xf000000000000000 - 0xf0003fffffffffff ]
  *
  * The proto-VSIDs are then scrambled into real VSIDs with the
  * multiplicative hash:
@@ -363,41 +362,49 @@ extern void slb_set_size(u16 size);
  * VSID_MULTIPLIER is prime, so in particular it is
  * co-prime to VSID_MODULUS, making this a 1:1 scrambling function.
  * Because the modulus is 2^n-1 we can compute it efficiently without
- * a divide or extra multiply (see below).
+ * a divide or extra multiply (see below). The scramble function gives
+ * robust scattering in the hash table (at least based on some initial
+ * results).
  *
- * This scheme has several advantages over older methods:
+ * We also consider VSID 0 special. We use VSID 0 for slb entries mapping
+ * bad address. This enables us to consolidate bad address handling in
+ * hash_page.
  *
- *	- We have VSIDs allocated for every kernel address
+ * We also need to avoid the last segment of the last context, because that
- * (i.e. everything above 0xC000000000000000), except the very top
+ * would give a protovsid of 0x1fffffffff. That will result in a VSID 0
- * segment, which simplifies several things.
+ * because of the modulo operation in vsid scramble. But the vmemmap
- *
+ * (which is what uses region 0xf) will never be close to 64TB in size
- *	- We allow for USER_ESID_BITS significant bits of ESID and
+ * (it's 56 bytes per page of system memory).
- * CONTEXT_BITS  bits of context for user addresses.
- *  i.e. 64T (46 bits) of address space for up to half a million contexts.
- *
- *	- The scramble function gives robust scattering in the hash
- * table (at least based on some initial results).  The previous
- * method was more susceptible to pathological cases giving excessive
- * hash collisions.
  */
 
+#define CONTEXT_BITS		19
+#define ESID_BITS		18
+#define ESID_BITS_1T		6
+
+/*
+ * 256MB segment
+ * The proto-VSID space has 2^(CONTEX_BITS + ESID_BITS) - 1 segments
+ * available for user + kernel mapping. The top 4 contexts are used for
+ * kernel mapping. Each segment contains 2^28 bytes. Each
+ * context maps 2^46 bytes (64TB) so we can support 2^19-1 contexts
+ * (19 == 37 + 28 - 46).
+ */
+#define MAX_USER_CONTEXT	((ASM_CONST(1) << CONTEXT_BITS) - 5)
+
 /*
  * This should be computed such that protovosid * vsid_mulitplier
  * doesn't overflow 64 bits. It should also be co-prime to vsid_modulus
  */
 #define VSID_MULTIPLIER_256M	ASM_CONST(12538073)	/* 24-bit prime */
-#define VSID_BITS_256M		38
+#define VSID_BITS_256M		(CONTEXT_BITS + ESID_BITS)
 #define VSID_MODULUS_256M	((1UL<<VSID_BITS_256M)-1)
 
 #define VSID_MULTIPLIER_1T	ASM_CONST(12538073)	/* 24-bit prime */
-#define VSID_BITS_1T		26
+#define VSID_BITS_1T		(CONTEXT_BITS + ESID_BITS_1T)
 #define VSID_MODULUS_1T		((1UL<<VSID_BITS_1T)-1)
 
-#define CONTEXT_BITS		19
-#define USER_ESID_BITS		18
-#define USER_ESID_BITS_1T	6
 
-#define USER_VSID_RANGE	(1UL << (USER_ESID_BITS + SID_SHIFT))
+#define USER_VSID_RANGE	(1UL << (ESID_BITS + SID_SHIFT))
 
 /*
  * This macro generates asm code to compute the VSID scramble
@@ -421,7 +428,8 @@ extern void slb_set_size(u16 size);
 	srdi	rx,rt,VSID_BITS_##size;					\
 	clrldi	rt,rt,(64-VSID_BITS_##size);				\
 	add	rt,rt,rx;		/* add high and low bits */	\
-	/* Now, r3 == VSID (mod 2^36-1), and lies between 0 and		\
+	/* NOTE: explanation based on VSID_BITS_##size = 36		\
+	 * Now, r3 == VSID (mod 2^36-1), and lies between 0 and		\
 	 * 2^36-1+2^28-1.  That in particular means that if r3 >=	\
 	 * 2^36-1, then r3+1 has the 2^36 bit set.  So, if r3+1 has	\
 	 * the bit clear, r3 already has the answer we want, if it	\
@@ -513,34 +521,6 @@ typedef struct {
 	})
 #endif /* 1 */
 
-/*
- * This is only valid for addresses >= PAGE_OFFSET
- * The proto-VSID space is divided into two class
- * User:   0 to 2^(CONTEXT_BITS + USER_ESID_BITS) -1
- * kernel: 2^(CONTEXT_BITS + USER_ESID_BITS) to 2^(VSID_BITS) - 1
- *
- * With KERNEL_START at 0xc000000000000000, the proto vsid for
- * the kernel ends up with 0xc00000000 (36 bits). With 64TB
- * support we need to have kernel proto-VSID in the
- * [2^37 to 2^38 - 1] range due to the increased USER_ESID_BITS.
- */
-static inline unsigned long get_kernel_vsid(unsigned long ea, int ssize)
-{
-	unsigned long proto_vsid;
-	/*
-	 * We need to make sure proto_vsid for the kernel is
-	 * >= 2^(CONTEXT_BITS + USER_ESID_BITS[_1T])
-	 */
-	if (ssize == MMU_SEGSIZE_256M) {
-		proto_vsid = ea >> SID_SHIFT;
-		proto_vsid |= (1UL << (CONTEXT_BITS + USER_ESID_BITS));
-		return vsid_scramble(proto_vsid, 256M);
-	}
-	proto_vsid = ea >> SID_SHIFT_1T;
-	proto_vsid |= (1UL << (CONTEXT_BITS + USER_ESID_BITS_1T));
-	return vsid_scramble(proto_vsid, 1T);
-}
-
 /* Returns the segment size indicator for a user address */
 static inline int user_segment_size(unsigned long addr)
 {
@@ -550,17 +530,41 @@ static inline int user_segment_size(unsigned long addr)
 	return MMU_SEGSIZE_256M;
 }
 
-/* This is only valid for user addresses (which are below 2^44) */
 static inline unsigned long get_vsid(unsigned long context, unsigned long ea,
 				     int ssize)
 {
+	/*
+	 * Bad address. We return VSID 0 for that
+	 */
+	if ((ea & ~REGION_MASK) >= PGTABLE_RANGE)
+		return 0;
+
 	if (ssize == MMU_SEGSIZE_256M)
-		return vsid_scramble((context << USER_ESID_BITS)
+		return vsid_scramble((context << ESID_BITS)
 				     | (ea >> SID_SHIFT), 256M);
-	return vsid_scramble((context << USER_ESID_BITS_1T)
+	return vsid_scramble((context << ESID_BITS_1T)
 			     | (ea >> SID_SHIFT_1T), 1T);
 }
 
+/*
+ * This is only valid for addresses >= PAGE_OFFSET
+ *
+ * For kernel space, we use the top 4 context ids to map address as below
+ * 0x7fffc -  [ 0xc000000000000000 - 0xc0003fffffffffff ]
+ * 0x7fffd -  [ 0xd000000000000000 - 0xd0003fffffffffff ]
+ * 0x7fffe -  [ 0xe000000000000000 - 0xe0003fffffffffff ]
+ * 0x7ffff -  [ 0xf000000000000000 - 0xf0003fffffffffff ]
+ */
+static inline unsigned long get_kernel_vsid(unsigned long ea, int ssize)
+{
+	unsigned long context;
+
+	/*
+	 * kernel take the top 4 context from the available range
+	 */
+	context = (MAX_USER_CONTEXT) + ((ea >> 60) - 0xc) + 1;
+	return get_vsid(context, ea, ssize);
+}
 #endif /* __ASSEMBLY__ */
 
 #endif /* _ASM_POWERPC_MMU_HASH64_H_ */

arch/powerpc/kernel/cputable.c

@@ -275,7 +275,7 @@ static struct cpu_spec __initdata cpu_specs[] = {
 		.cpu_features		= CPU_FTRS_PPC970,
 		.cpu_user_features	= COMMON_USER_POWER4 |
 			PPC_FEATURE_HAS_ALTIVEC_COMP,
-		.mmu_features		= MMU_FTR_HPTE_TABLE,
+		.mmu_features		= MMU_FTRS_PPC970,
 		.icache_bsize		= 128,
 		.dcache_bsize		= 128,
 		.num_pmcs		= 8,

arch/powerpc/kernel/epapr_paravirt.c

@@ -23,8 +23,10 @@
 #include <asm/code-patching.h>
 #include <asm/machdep.h>
 
+#if !defined(CONFIG_64BIT) || defined(CONFIG_PPC_BOOK3E_64)
 extern void epapr_ev_idle(void);
 extern u32 epapr_ev_idle_start[];
+#endif
 
 bool epapr_paravirt_enabled;
 
@@ -47,11 +49,15 @@ static int __init epapr_paravirt_init(void)
 
 	for (i = 0; i < (len / 4); i++) {
 		patch_instruction(epapr_hypercall_start + i, insts[i]);
+#if !defined(CONFIG_64BIT) || defined(CONFIG_PPC_BOOK3E_64)
 		patch_instruction(epapr_ev_idle_start + i, insts[i]);
+#endif
 	}
 
+#if !defined(CONFIG_64BIT) || defined(CONFIG_PPC_BOOK3E_64)
 	if (of_get_property(hyper_node, "has-idle", NULL))
 		ppc_md.power_save = epapr_ev_idle;
+#endif
 
 	epapr_paravirt_enabled = true;
 

arch/powerpc/kernel/exceptions-64s.S

@@ -1066,78 +1066,6 @@ unrecov_user_slb:
 #endif /* __DISABLED__ */
 
 
-/*
- * r13 points to the PACA, r9 contains the saved CR,
- * r12 contain the saved SRR1, SRR0 is still ready for return
- * r3 has the faulting address
- * r9 - r13 are saved in paca->exslb.
- * r3 is saved in paca->slb_r3
- * We assume we aren't going to take any exceptions during this procedure.
- */
-_GLOBAL(slb_miss_realmode)
-	mflr	r10
-#ifdef CONFIG_RELOCATABLE
-	mtctr	r11
-#endif
-
-	stw	r9,PACA_EXSLB+EX_CCR(r13)	/* save CR in exc. frame */
-	std	r10,PACA_EXSLB+EX_LR(r13)	/* save LR */
-
-	bl	.slb_allocate_realmode
-
-	/* All done -- return from exception. */
-
-	ld	r10,PACA_EXSLB+EX_LR(r13)
-	ld	r3,PACA_EXSLB+EX_R3(r13)
-	lwz	r9,PACA_EXSLB+EX_CCR(r13)	/* get saved CR */
-
-	mtlr	r10
-
-	andi.	r10,r12,MSR_RI	/* check for unrecoverable exception */
-	beq-	2f
-
-.machine	push
-.machine	"power4"
-	mtcrf	0x80,r9
-	mtcrf	0x01,r9		/* slb_allocate uses cr0 and cr7 */
-.machine	pop
-
-	RESTORE_PPR_PACA(PACA_EXSLB, r9)
-	ld	r9,PACA_EXSLB+EX_R9(r13)
-	ld	r10,PACA_EXSLB+EX_R10(r13)
-	ld	r11,PACA_EXSLB+EX_R11(r13)
-	ld	r12,PACA_EXSLB+EX_R12(r13)
-	ld	r13,PACA_EXSLB+EX_R13(r13)
-	rfid
-	b	.	/* prevent speculative execution */
-
-2:	mfspr	r11,SPRN_SRR0
-	ld	r10,PACAKBASE(r13)
-	LOAD_HANDLER(r10,unrecov_slb)
-	mtspr	SPRN_SRR0,r10
-	ld	r10,PACAKMSR(r13)
-	mtspr	SPRN_SRR1,r10
-	rfid
-	b	.
-
-unrecov_slb:
-	EXCEPTION_PROLOG_COMMON(0x4100, PACA_EXSLB)
-	DISABLE_INTS
-	bl	.save_nvgprs
-1:	addi	r3,r1,STACK_FRAME_OVERHEAD
-	bl	.unrecoverable_exception
-	b	1b
-
-
-#ifdef CONFIG_PPC_970_NAP
-power4_fixup_nap:
-	andc	r9,r9,r10
-	std	r9,TI_LOCAL_FLAGS(r11)
-	ld	r10,_LINK(r1)		/* make idle task do the */
-	std	r10,_NIP(r1)		/* equivalent of a blr */
-	blr
-#endif
-
 	.align	7
 	.globl alignment_common
 alignment_common:
@@ -1335,6 +1263,78 @@ _GLOBAL(opal_mc_secondary_handler)
 #endif /* CONFIG_PPC_POWERNV */
 
 
+/*
+ * r13 points to the PACA, r9 contains the saved CR,
+ * r12 contain the saved SRR1, SRR0 is still ready for return
+ * r3 has the faulting address
+ * r9 - r13 are saved in paca->exslb.
+ * r3 is saved in paca->slb_r3
+ * We assume we aren't going to take any exceptions during this procedure.
+ */
+_GLOBAL(slb_miss_realmode)
+	mflr	r10
+#ifdef CONFIG_RELOCATABLE
+	mtctr	r11
+#endif
+
+	stw	r9,PACA_EXSLB+EX_CCR(r13)	/* save CR in exc. frame */
+	std	r10,PACA_EXSLB+EX_LR(r13)	/* save LR */
+
+	bl	.slb_allocate_realmode
+
+	/* All done -- return from exception. */
+
+	ld	r10,PACA_EXSLB+EX_LR(r13)
+	ld	r3,PACA_EXSLB+EX_R3(r13)
+	lwz	r9,PACA_EXSLB+EX_CCR(r13)	/* get saved CR */
+
+	mtlr	r10
+
+	andi.	r10,r12,MSR_RI	/* check for unrecoverable exception */
+	beq-	2f
+
+.machine	push
+.machine	"power4"
+	mtcrf	0x80,r9
+	mtcrf	0x01,r9		/* slb_allocate uses cr0 and cr7 */
+.machine	pop
+
+	RESTORE_PPR_PACA(PACA_EXSLB, r9)
+	ld	r9,PACA_EXSLB+EX_R9(r13)
+	ld	r10,PACA_EXSLB+EX_R10(r13)
+	ld	r11,PACA_EXSLB+EX_R11(r13)
+	ld	r12,PACA_EXSLB+EX_R12(r13)
+	ld	r13,PACA_EXSLB+EX_R13(r13)
+	rfid
+	b	.	/* prevent speculative execution */
+
+2:	mfspr	r11,SPRN_SRR0
+	ld	r10,PACAKBASE(r13)
+	LOAD_HANDLER(r10,unrecov_slb)
+	mtspr	SPRN_SRR0,r10
+	ld	r10,PACAKMSR(r13)
+	mtspr	SPRN_SRR1,r10
+	rfid
+	b	.
+
+unrecov_slb:
+	EXCEPTION_PROLOG_COMMON(0x4100, PACA_EXSLB)
+	DISABLE_INTS
+	bl	.save_nvgprs
+1:	addi	r3,r1,STACK_FRAME_OVERHEAD
+	bl	.unrecoverable_exception
+	b	1b
+
+
+#ifdef CONFIG_PPC_970_NAP
+power4_fixup_nap:
+	andc	r9,r9,r10
+	std	r9,TI_LOCAL_FLAGS(r11)
+	ld	r10,_LINK(r1)		/* make idle task do the */
+	std	r10,_NIP(r1)		/* equivalent of a blr */
+	blr
+#endif
+
 /*
  * Hash table stuff
  */
@@ -1452,20 +1452,36 @@ do_ste_alloc:
 _GLOBAL(do_stab_bolted)
 	stw	r9,PACA_EXSLB+EX_CCR(r13)	/* save CR in exc. frame */
 	std	r11,PACA_EXSLB+EX_SRR0(r13)	/* save SRR0 in exc. frame */
+	mfspr	r11,SPRN_DAR			/* ea */
 
+	/*
+	 * check for bad kernel/user address
+	 * (ea & ~REGION_MASK) >= PGTABLE_RANGE
+	 */
+	rldicr. r9,r11,4,(63 - 46 - 4)
+	li	r9,0	/* VSID = 0 for bad address */
+	bne-	0f
+
+	/*
+	 * Calculate VSID:
+	 * This is the kernel vsid, we take the top for context from
+	 * the range. context = (MAX_USER_CONTEXT) + ((ea >> 60) - 0xc) + 1
+	 * Here we know that (ea >> 60) == 0xc
+	 */
+	lis	r9,(MAX_USER_CONTEXT + 1)@ha
+	addi	r9,r9,(MAX_USER_CONTEXT + 1)@l
+
+	srdi	r10,r11,SID_SHIFT
+	rldimi  r10,r9,ESID_BITS,0 /* proto vsid */
+	ASM_VSID_SCRAMBLE(r10, r9, 256M)
+	rldic	r9,r10,12,16	/* r9 = vsid << 12 */
+
+0:
 	/* Hash to the primary group */
 	ld	r10,PACASTABVIRT(r13)
-	mfspr	r11,SPRN_DAR
+	srdi	r11,r11,SID_SHIFT
-	srdi	r11,r11,28
 	rldimi	r10,r11,7,52	/* r10 = first ste of the group */
 
-	/* Calculate VSID */
-	/* This is a kernel address, so protovsid = ESID | 1 << 37 */
-	li	r9,0x1
-	rldimi  r11,r9,(CONTEXT_BITS + USER_ESID_BITS),0
-	ASM_VSID_SCRAMBLE(r11, r9, 256M)
-	rldic	r9,r11,12,16	/* r9 = vsid << 12 */
-
 	/* Search the primary group for a free entry */
 1:	ld	r11,0(r10)	/* Test valid bit of the current ste	*/
 	andi.	r11,r11,0x80

arch/powerpc/kernel/prom_init.c

@@ -2832,11 +2832,13 @@ static void unreloc_toc(void)
 {
 }
 #else
-static void __reloc_toc(void *tocstart, unsigned long offset,
+static void __reloc_toc(unsigned long offset, unsigned long nr_entries)
-			unsigned long nr_entries)
 {
 	unsigned long i;
-	unsigned long *toc_entry = (unsigned long *)tocstart;
+	unsigned long *toc_entry;
+
+	/* Get the start of the TOC by using r2 directly. */
+	asm volatile("addi %0,2,-0x8000" : "=b" (toc_entry));
 
 	for (i = 0; i < nr_entries; i++) {
 		*toc_entry = *toc_entry + offset;
@@ -2850,8 +2852,7 @@ static void reloc_toc(void)
 	unsigned long nr_entries =
 		(__prom_init_toc_end - __prom_init_toc_start) / sizeof(long);
 
-	/* Need to add offset to get at __prom_init_toc_start */
+	__reloc_toc(offset, nr_entries);
-	__reloc_toc(__prom_init_toc_start + offset, offset, nr_entries);
 
 	mb();
 }
@@ -2864,8 +2865,7 @@ static void unreloc_toc(void)
 
 	mb();
 
-	/* __prom_init_toc_start has been relocated, no need to add offset */
+	__reloc_toc(-offset, nr_entries);
-	__reloc_toc(__prom_init_toc_start, -offset, nr_entries);
 }
 #endif
 #endif

arch/powerpc/kernel/ptrace.c

@@ -1428,6 +1428,7 @@ static long ppc_set_hwdebug(struct task_struct *child,
 
 	brk.address = bp_info->addr & ~7UL;
 	brk.type = HW_BRK_TYPE_TRANSLATE;
+	brk.len = 8;
 	if (bp_info->trigger_type & PPC_BREAKPOINT_TRIGGER_READ)
 		brk.type |= HW_BRK_TYPE_READ;
 	if (bp_info->trigger_type & PPC_BREAKPOINT_TRIGGER_WRITE)

arch/powerpc/kvm/book3s_64_mmu_host.c

@@ -326,8 +326,8 @@ int kvmppc_mmu_init(struct kvm_vcpu *vcpu)
 	vcpu3s->context_id[0] = err;
 
 	vcpu3s->proto_vsid_max = ((vcpu3s->context_id[0] + 1)
-				  << USER_ESID_BITS) - 1;
+				  << ESID_BITS) - 1;
-	vcpu3s->proto_vsid_first = vcpu3s->context_id[0] << USER_ESID_BITS;
+	vcpu3s->proto_vsid_first = vcpu3s->context_id[0] << ESID_BITS;
 	vcpu3s->proto_vsid_next = vcpu3s->proto_vsid_first;
 
 	kvmppc_mmu_hpte_init(vcpu);

arch/powerpc/mm/hash_utils_64.c

@@ -195,6 +195,11 @@ int htab_bolt_mapping(unsigned long vstart, unsigned long vend,
 		unsigned long vpn  = hpt_vpn(vaddr, vsid, ssize);
 		unsigned long tprot = prot;
 
+		/*
+		 * If we hit a bad address return error.
+		 */
+		if (!vsid)
+			return -1;
 		/* Make kernel text executable */
 		if (overlaps_kernel_text(vaddr, vaddr + step))
 			tprot &= ~HPTE_R_N;
@@ -759,6 +764,8 @@ void __init early_init_mmu(void)
 	/* Initialize stab / SLB management */
 	if (mmu_has_feature(MMU_FTR_SLB))
 		slb_initialize();
+	else
+		stab_initialize(get_paca()->stab_real);
 }
 
 #ifdef CONFIG_SMP
@@ -922,11 +929,6 @@ int hash_page(unsigned long ea, unsigned long access, unsigned long trap)
 	DBG_LOW("hash_page(ea=%016lx, access=%lx, trap=%lx\n",
 		ea, access, trap);
 
-	if ((ea & ~REGION_MASK) >= PGTABLE_RANGE) {
-		DBG_LOW(" out of pgtable range !\n");
- 		return 1;
-	}
-
 	/* Get region & vsid */
  	switch (REGION_ID(ea)) {
 	case USER_REGION_ID:
@@ -957,6 +959,11 @@ int hash_page(unsigned long ea, unsigned long access, unsigned long trap)
 	}
 	DBG_LOW(" mm=%p, mm->pgdir=%p, vsid=%016lx\n", mm, mm->pgd, vsid);
 
+	/* Bad address. */
+	if (!vsid) {
+		DBG_LOW("Bad address!\n");
+		return 1;
+	}
 	/* Get pgdir */
 	pgdir = mm->pgd;
 	if (pgdir == NULL)
@@ -1126,6 +1133,8 @@ void hash_preload(struct mm_struct *mm, unsigned long ea,
 	/* Get VSID */
 	ssize = user_segment_size(ea);
 	vsid = get_vsid(mm->context.id, ea, ssize);
+	if (!vsid)
+		return;
 
 	/* Hash doesn't like irqs */
 	local_irq_save(flags);
@@ -1233,6 +1242,9 @@ static void kernel_map_linear_page(unsigned long vaddr, unsigned long lmi)
 	hash = hpt_hash(vpn, PAGE_SHIFT, mmu_kernel_ssize);
 	hpteg = ((hash & htab_hash_mask) * HPTES_PER_GROUP);
 
+	/* Don't create HPTE entries for bad address */
+	if (!vsid)
+		return;
 	ret = ppc_md.hpte_insert(hpteg, vpn, __pa(vaddr),
 				 mode, HPTE_V_BOLTED,
 				 mmu_linear_psize, mmu_kernel_ssize);

arch/powerpc/mm/mmu_context_hash64.c

@@ -29,15 +29,6 @@
 static DEFINE_SPINLOCK(mmu_context_lock);
 static DEFINE_IDA(mmu_context_ida);
 
-/*
- * 256MB segment
- * The proto-VSID space has 2^(CONTEX_BITS + USER_ESID_BITS) - 1 segments
- * available for user mappings. Each segment contains 2^28 bytes. Each
- * context maps 2^46 bytes (64TB) so we can support 2^19-1 contexts
- * (19 == 37 + 28 - 46).
- */
-#define MAX_CONTEXT	((1UL << CONTEXT_BITS) - 1)
-
 int __init_new_context(void)
 {
 	int index;
@@ -56,7 +47,7 @@ again:
 	else if (err)
 		return err;
 
-	if (index > MAX_CONTEXT) {
+	if (index > MAX_USER_CONTEXT) {
 		spin_lock(&mmu_context_lock);
 		ida_remove(&mmu_context_ida, index);
 		spin_unlock(&mmu_context_lock);

arch/powerpc/mm/pgtable_64.c

@@ -61,7 +61,7 @@
 #endif
 
 #ifdef CONFIG_PPC_STD_MMU_64
-#if TASK_SIZE_USER64 > (1UL << (USER_ESID_BITS + SID_SHIFT))
+#if TASK_SIZE_USER64 > (1UL << (ESID_BITS + SID_SHIFT))
 #error TASK_SIZE_USER64 exceeds user VSID range
 #endif
 #endif

arch/powerpc/mm/slb_low.S

@@ -31,10 +31,15 @@
  * No other registers are examined or changed.
  */
 _GLOBAL(slb_allocate_realmode)
-	/* r3 = faulting address */
+	/*
+	 * check for bad kernel/user address
+	 * (ea & ~REGION_MASK) >= PGTABLE_RANGE
+	 */
+	rldicr. r9,r3,4,(63 - 46 - 4)
+	bne-	8f
 
 	srdi	r9,r3,60		/* get region */
-	srdi	r10,r3,28		/* get esid */
+	srdi	r10,r3,SID_SHIFT	/* get esid */
 	cmpldi	cr7,r9,0xc		/* cmp PAGE_OFFSET for later use */
 
 	/* r3 = address, r10 = esid, cr7 = <> PAGE_OFFSET */
@@ -56,12 +61,14 @@ _GLOBAL(slb_allocate_realmode)
 	 */
 _GLOBAL(slb_miss_kernel_load_linear)
 	li	r11,0
-	li	r9,0x1
 	/*
-	 * for 1T we shift 12 bits more.  slb_finish_load_1T will do
+	 * context = (MAX_USER_CONTEXT) + ((ea >> 60) - 0xc) + 1
-	 * the necessary adjustment
+	 * r9 = region id.
 	 */
-	rldimi  r10,r9,(CONTEXT_BITS + USER_ESID_BITS),0
+	addis	r9,r9,(MAX_USER_CONTEXT - 0xc + 1)@ha
+	addi	r9,r9,(MAX_USER_CONTEXT - 0xc + 1)@l
+
+
 BEGIN_FTR_SECTION
 	b	slb_finish_load
 END_MMU_FTR_SECTION_IFCLR(MMU_FTR_1T_SEGMENT)
@@ -91,24 +98,19 @@ _GLOBAL(slb_miss_kernel_load_vmemmap)
 	_GLOBAL(slb_miss_kernel_load_io)
 	li	r11,0
 6:
-	li	r9,0x1
 	/*
-	 * for 1T we shift 12 bits more.  slb_finish_load_1T will do
+	 * context = (MAX_USER_CONTEXT) + ((ea >> 60) - 0xc) + 1
-	 * the necessary adjustment
+	 * r9 = region id.
 	 */
-	rldimi  r10,r9,(CONTEXT_BITS + USER_ESID_BITS),0
+	addis	r9,r9,(MAX_USER_CONTEXT - 0xc + 1)@ha
+	addi	r9,r9,(MAX_USER_CONTEXT - 0xc + 1)@l
+
 BEGIN_FTR_SECTION
 	b	slb_finish_load
 END_MMU_FTR_SECTION_IFCLR(MMU_FTR_1T_SEGMENT)
 	b	slb_finish_load_1T
 
-0:	/* user address: proto-VSID = context << 15 | ESID. First check
+0:
-	 * if the address is within the boundaries of the user region
-	 */
-	srdi.	r9,r10,USER_ESID_BITS
-	bne-	8f			/* invalid ea bits set */
-
-
 	/* when using slices, we extract the psize off the slice bitmaps
 	 * and then we need to get the sllp encoding off the mmu_psize_defs
 	 * array.
@@ -164,15 +166,13 @@ END_MMU_FTR_SECTION_IFCLR(MMU_FTR_1T_SEGMENT)
 	ld	r9,PACACONTEXTID(r13)
 BEGIN_FTR_SECTION
 	cmpldi	r10,0x1000
-END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
-	rldimi	r10,r9,USER_ESID_BITS,0
-BEGIN_FTR_SECTION
 	bge	slb_finish_load_1T
 END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
 	b	slb_finish_load
 
 8:	/* invalid EA */
 	li	r10,0			/* BAD_VSID */
+	li	r9,0			/* BAD_VSID */
 	li	r11,SLB_VSID_USER	/* flags don't much matter */
 	b	slb_finish_load
 
@@ -221,8 +221,6 @@ _GLOBAL(slb_allocate_user)
 
 	/* get context to calculate proto-VSID */
 	ld	r9,PACACONTEXTID(r13)
-	rldimi	r10,r9,USER_ESID_BITS,0
-
 	/* fall through slb_finish_load */
 
 #endif /* __DISABLED__ */
@@ -231,9 +229,10 @@ _GLOBAL(slb_allocate_user)
 /*
  * Finish loading of an SLB entry and return
  *
- * r3 = EA, r10 = proto-VSID, r11 = flags, clobbers r9, cr7 = <> PAGE_OFFSET
+ * r3 = EA, r9 = context, r10 = ESID, r11 = flags, clobbers r9, cr7 = <> PAGE_OFFSET
  */
 slb_finish_load:
+	rldimi  r10,r9,ESID_BITS,0
 	ASM_VSID_SCRAMBLE(r10,r9,256M)
 	/*
 	 * bits above VSID_BITS_256M need to be ignored from r10
@@ -298,10 +297,11 @@ _GLOBAL(slb_compare_rr_to_size)
 /*
  * Finish loading of a 1T SLB entry (for the kernel linear mapping) and return.
  *
- * r3 = EA, r10 = proto-VSID, r11 = flags, clobbers r9
+ * r3 = EA, r9 = context, r10 = ESID(256MB), r11 = flags, clobbers r9
  */
 slb_finish_load_1T:
-	srdi	r10,r10,40-28		/* get 1T ESID */
+	srdi	r10,r10,(SID_SHIFT_1T - SID_SHIFT)	/* get 1T ESID */
+	rldimi  r10,r9,ESID_BITS_1T,0
 	ASM_VSID_SCRAMBLE(r10,r9,1T)
 	/*
 	 * bits above VSID_BITS_1T need to be ignored from r10

arch/powerpc/mm/tlb_hash64.c

@@ -82,11 +82,11 @@ void hpte_need_flush(struct mm_struct *mm, unsigned long addr,
 	if (!is_kernel_addr(addr)) {
 		ssize = user_segment_size(addr);
 		vsid = get_vsid(mm->context.id, addr, ssize);
-		WARN_ON(vsid == 0);
 	} else {
 		vsid = get_kernel_vsid(addr, mmu_kernel_ssize);
 		ssize = mmu_kernel_ssize;
 	}
+	WARN_ON(vsid == 0);
 	vpn = hpt_vpn(addr, vsid, ssize);
 	rpte = __real_pte(__pte(pte), ptep);
 

arch/powerpc/perf/power7-pmu.c

@@ -420,7 +420,20 @@ static struct attribute_group power7_pmu_events_group = {
 	.attrs = power7_events_attr,
 };
 
+PMU_FORMAT_ATTR(event, "config:0-19");
+
+static struct attribute *power7_pmu_format_attr[] = {
+	&format_attr_event.attr,
+	NULL,
+};
+
+struct attribute_group power7_pmu_format_group = {
+	.name = "format",
+	.attrs = power7_pmu_format_attr,
+};
+
 static const struct attribute_group *power7_pmu_attr_groups[] = {
+	&power7_pmu_format_group,
 	&power7_pmu_events_group,
 	NULL,
 };

arch/powerpc/platforms/85xx/sgy_cts1000.c

@@ -69,7 +69,7 @@ static irqreturn_t gpio_halt_irq(int irq, void *__data)
         return IRQ_HANDLED;
 };
 
-static int __devinit gpio_halt_probe(struct platform_device *pdev)
+static int gpio_halt_probe(struct platform_device *pdev)
 {
 	enum of_gpio_flags flags;
 	struct device_node *node = pdev->dev.of_node;
@@ -128,7 +128,7 @@ static int __devinit gpio_halt_probe(struct platform_device *pdev)
 	return 0;
 }
 
-static int __devexit gpio_halt_remove(struct platform_device *pdev)
+static int gpio_halt_remove(struct platform_device *pdev)
 {
 	if (halt_node) {
 		int gpio = of_get_gpio(halt_node, 0);
@@ -165,7 +165,7 @@ static struct platform_driver gpio_halt_driver = {
 		.of_match_table = gpio_halt_match,
 	},
 	.probe		= gpio_halt_probe,
-	.remove		= __devexit_p(gpio_halt_remove),
+	.remove		= gpio_halt_remove,
 };
 
 module_platform_driver(gpio_halt_driver);

arch/powerpc/platforms/Kconfig.cputype

@@ -124,9 +124,8 @@ config 6xx
 	select PPC_HAVE_PMU_SUPPORT
 
 config POWER3
-	bool
 	depends on PPC64 && PPC_BOOK3S
-	default y if !POWER4_ONLY
+	def_bool y
 
 config POWER4
 	depends on PPC64 && PPC_BOOK3S
@@ -145,8 +144,7 @@ config TUNE_CELL
 	  but somewhat slower on other machines. This option only changes
 	  the scheduling of instructions, not the selection of instructions
 	  itself, so the resulting kernel will keep running on all other
-	  machines. When building a kernel that is supposed to run only
+	  machines.
-	  on Cell, you should also select the POWER4_ONLY option.
 
 # this is temp to handle compat with arch=ppc
 config 8xx

arch/s390/include/asm/eadm.h

@@ -34,6 +34,8 @@ struct arsb {
 	u32 reserved[4];
 } __packed;
 
+#define EQC_WR_PROHIBIT 22
+
 struct msb {
 	u8 fmt:4;
 	u8 oc:4;
@@ -96,11 +98,13 @@ struct scm_device {
 #define OP_STATE_TEMP_ERR	2
 #define OP_STATE_PERM_ERR	3
 
+enum scm_event {SCM_CHANGE, SCM_AVAIL};
+
 struct scm_driver {
 	struct device_driver drv;
 	int (*probe) (struct scm_device *scmdev);
 	int (*remove) (struct scm_device *scmdev);
-	void (*notify) (struct scm_device *scmdev);
+	void (*notify) (struct scm_device *scmdev, enum scm_event event);
 	void (*handler) (struct scm_device *scmdev, void *data, int error);
 };
 

arch/s390/include/asm/tlbflush.h

@@ -74,8 +74,6 @@ static inline void __tlb_flush_idte(unsigned long asce)
 
 static inline void __tlb_flush_mm(struct mm_struct * mm)
 {
-	if (unlikely(cpumask_empty(mm_cpumask(mm))))
-		return;
 	/*
 	 * If the machine has IDTE we prefer to do a per mm flush
 	 * on all cpus instead of doing a local flush if the mm

arch/s390/kernel/entry.S

@@ -636,7 +636,8 @@ ENTRY(mcck_int_handler)
 	UPDATE_VTIME %r14,%r15,__LC_MCCK_ENTER_TIMER
 mcck_skip:
 	SWITCH_ASYNC __LC_GPREGS_SAVE_AREA+32,__LC_PANIC_STACK,PAGE_SHIFT
-	mvc	__PT_R0(64,%r11),__LC_GPREGS_SAVE_AREA
+	stm	%r0,%r7,__PT_R0(%r11)
+	mvc	__PT_R8(32,%r11),__LC_GPREGS_SAVE_AREA+32
 	stm	%r8,%r9,__PT_PSW(%r11)
 	xc	__SF_BACKCHAIN(4,%r15),__SF_BACKCHAIN(%r15)
 	l	%r1,BASED(.Ldo_machine_check)

arch/s390/kernel/entry64.S

@@ -678,8 +678,9 @@ ENTRY(mcck_int_handler)
 	UPDATE_VTIME %r14,__LC_MCCK_ENTER_TIMER
 	LAST_BREAK %r14
 mcck_skip:
-	lghi	%r14,__LC_GPREGS_SAVE_AREA
+	lghi	%r14,__LC_GPREGS_SAVE_AREA+64
-	mvc	__PT_R0(128,%r11),0(%r14)
+	stmg	%r0,%r7,__PT_R0(%r11)
+	mvc	__PT_R8(64,%r11),0(%r14)
 	stmg	%r8,%r9,__PT_PSW(%r11)
 	xc	__SF_BACKCHAIN(8,%r15),__SF_BACKCHAIN(%r15)
 	lgr	%r2,%r11		# pass pointer to pt_regs

arch/s390/kernel/setup.c

@@ -571,6 +571,8 @@ static void __init setup_memory_end(void)
 
 	/* Split remaining virtual space between 1:1 mapping & vmemmap array */
 	tmp = VMALLOC_START / (PAGE_SIZE + sizeof(struct page));
+	/* vmemmap contains a multiple of PAGES_PER_SECTION struct pages */
+	tmp = SECTION_ALIGN_UP(tmp);
 	tmp = VMALLOC_START - tmp * sizeof(struct page);
 	tmp &= ~((vmax >> 11) - 1);	/* align to page table level */
 	tmp = min(tmp, 1UL << MAX_PHYSMEM_BITS);

arch/sparc/Kconfig

@@ -84,12 +84,6 @@ config ARCH_DEFCONFIG
 	default "arch/sparc/configs/sparc32_defconfig" if SPARC32
 	default "arch/sparc/configs/sparc64_defconfig" if SPARC64
 
-# CONFIG_BITS can be used at source level to get 32/64 bits
-config BITS
-	int
-	default 32 if SPARC32
-	default 64 if SPARC64
-
 config IOMMU_HELPER
 	bool
 	default y if SPARC64
@@ -197,7 +191,7 @@ config RWSEM_XCHGADD_ALGORITHM
 
 config GENERIC_HWEIGHT
 	bool
-	default y if !ULTRA_HAS_POPULATION_COUNT
+	default y
 
 config GENERIC_CALIBRATE_DELAY
 	bool

arch/sparc/include/asm/spitfire.h

@@ -45,6 +45,7 @@
 #define SUN4V_CHIP_NIAGARA3	0x03
 #define SUN4V_CHIP_NIAGARA4	0x04
 #define SUN4V_CHIP_NIAGARA5	0x05
+#define SUN4V_CHIP_SPARC64X	0x8a
 #define SUN4V_CHIP_UNKNOWN	0xff
 
 #ifndef __ASSEMBLY__

arch/sparc/kernel/cpu.c

@@ -493,6 +493,12 @@ static void __init sun4v_cpu_probe(void)
 		sparc_pmu_type = "niagara5";
 		break;
 
+	case SUN4V_CHIP_SPARC64X:
+		sparc_cpu_type = "SPARC64-X";
+		sparc_fpu_type = "SPARC64-X integrated FPU";
+		sparc_pmu_type = "sparc64-x";
+		break;
+
 	default:
 		printk(KERN_WARNING "CPU: Unknown sun4v cpu type [%s]\n",
 		       prom_cpu_compatible);

arch/sparc/kernel/head_64.S

@@ -134,6 +134,8 @@ prom_niagara_prefix:
 	.asciz	"SUNW,UltraSPARC-T"
 prom_sparc_prefix:
 	.asciz	"SPARC-"
+prom_sparc64x_prefix:
+	.asciz	"SPARC64-X"
 	.align	4
 prom_root_compatible:
 	.skip	64
@@ -412,7 +414,7 @@ sun4v_chip_type:
 	cmp	%g2, 'T'
 	be,pt	%xcc, 70f
 	 cmp	%g2, 'M'
-	bne,pn	%xcc, 4f
+	bne,pn	%xcc, 49f
 	 nop
 
 70:	ldub	[%g1 + 7], %g2
@@ -425,7 +427,7 @@ sun4v_chip_type:
 	cmp	%g2, '5'
 	be,pt	%xcc, 5f
 	 mov	SUN4V_CHIP_NIAGARA5, %g4
-	ba,pt	%xcc, 4f
+	ba,pt	%xcc, 49f
 	 nop
 
 91:	sethi	%hi(prom_cpu_compatible), %g1
@@ -439,6 +441,25 @@ sun4v_chip_type:
 	 mov	SUN4V_CHIP_NIAGARA2, %g4
 	
 4:
+	/* Athena */
+	sethi	%hi(prom_cpu_compatible), %g1
+	or	%g1, %lo(prom_cpu_compatible), %g1
+	sethi	%hi(prom_sparc64x_prefix), %g7
+	or	%g7, %lo(prom_sparc64x_prefix), %g7
+	mov	9, %g3
+41:	ldub	[%g7], %g2
+	ldub	[%g1], %g4
+	cmp	%g2, %g4
+	bne,pn	%icc, 49f
+	add	%g7, 1, %g7
+	subcc	%g3, 1, %g3
+	bne,pt	%xcc, 41b
+	add	%g1, 1, %g1
+	mov	SUN4V_CHIP_SPARC64X, %g4
+	ba,pt	%xcc, 5f
+	nop
+
+49:
 	mov	SUN4V_CHIP_UNKNOWN, %g4
 5:	sethi	%hi(sun4v_chip_type), %g2
 	or	%g2, %lo(sun4v_chip_type), %g2

arch/sparc/kernel/leon_pci_grpci2.c

@@ -186,6 +186,8 @@ struct grpci2_cap_first {
 #define CAP9_IOMAP_OFS 0x20
 #define CAP9_BARSIZE_OFS 0x24
 
+#define TGT 256
+
 struct grpci2_priv {
 	struct leon_pci_info	info; /* must be on top of this structure */
 	struct grpci2_regs	*regs;
@@ -237,8 +239,12 @@ static int grpci2_cfg_r32(struct grpci2_priv *priv, unsigned int bus,
 	if (where & 0x3)
 		return -EINVAL;
 
-	if (bus == 0 && PCI_SLOT(devfn) != 0)
+	if (bus == 0) {
-		devfn += (0x8 * 6);
+		devfn += (0x8 * 6); /* start at AD16=Device0 */
+	} else if (bus == TGT) {
+		bus = 0;
+		devfn = 0; /* special case: bridge controller itself */
+	}
 
 	/* Select bus */
 	spin_lock_irqsave(&grpci2_dev_lock, flags);
@@ -303,8 +309,12 @@ static int grpci2_cfg_w32(struct grpci2_priv *priv, unsigned int bus,
 	if (where & 0x3)
 		return -EINVAL;
 
-	if (bus == 0 && PCI_SLOT(devfn) != 0)
+	if (bus == 0) {
-		devfn += (0x8 * 6);
+		devfn += (0x8 * 6); /* start at AD16=Device0 */
+	} else if (bus == TGT) {
+		bus = 0;
+		devfn = 0; /* special case: bridge controller itself */
+	}
 
 	/* Select bus */
 	spin_lock_irqsave(&grpci2_dev_lock, flags);
@@ -368,7 +378,7 @@ static int grpci2_read_config(struct pci_bus *bus, unsigned int devfn,
 	unsigned int busno = bus->number;
 	int ret;
 
-	if (PCI_SLOT(devfn) > 15 || (PCI_SLOT(devfn) == 0 && busno == 0)) {
+	if (PCI_SLOT(devfn) > 15 || busno > 255) {
 		*val = ~0;
 		return 0;
 	}
@@ -406,7 +416,7 @@ static int grpci2_write_config(struct pci_bus *bus, unsigned int devfn,
 	struct grpci2_priv *priv = grpci2priv;
 	unsigned int busno = bus->number;
 
-	if (PCI_SLOT(devfn) > 15 || (PCI_SLOT(devfn) == 0 && busno == 0))
+	if (PCI_SLOT(devfn) > 15 || busno > 255)
 		return 0;
 
 #ifdef GRPCI2_DEBUG_CFGACCESS
@@ -578,15 +588,15 @@ void grpci2_hw_init(struct grpci2_priv *priv)
 		REGSTORE(regs->ahbmst_map[i], priv->pci_area);
 
 	/* Get the GRPCI2 Host PCI ID */
-	grpci2_cfg_r32(priv, 0, 0, PCI_VENDOR_ID, &priv->pciid);
+	grpci2_cfg_r32(priv, TGT, 0, PCI_VENDOR_ID, &priv->pciid);
 
 	/* Get address to first (always defined) capability structure */
-	grpci2_cfg_r8(priv, 0, 0, PCI_CAPABILITY_LIST, &capptr);
+	grpci2_cfg_r8(priv, TGT, 0, PCI_CAPABILITY_LIST, &capptr);
 
 	/* Enable/Disable Byte twisting */
-	grpci2_cfg_r32(priv, 0, 0, capptr+CAP9_IOMAP_OFS, &io_map);
+	grpci2_cfg_r32(priv, TGT, 0, capptr+CAP9_IOMAP_OFS, &io_map);
 	io_map = (io_map & ~0x1) | (priv->bt_enabled ? 1 : 0);
-	grpci2_cfg_w32(priv, 0, 0, capptr+CAP9_IOMAP_OFS, io_map);
+	grpci2_cfg_w32(priv, TGT, 0, capptr+CAP9_IOMAP_OFS, io_map);
 
 	/* Setup the Host's PCI Target BARs for other peripherals to access,
 	 * and do DMA to the host's memory. The target BARs can be sized and
@@ -617,17 +627,18 @@ void grpci2_hw_init(struct grpci2_priv *priv)
 				pciadr = 0;
 			}
 		}
-		grpci2_cfg_w32(priv, 0, 0, capptr+CAP9_BARSIZE_OFS+i*4, bar_sz);
+		grpci2_cfg_w32(priv, TGT, 0, capptr+CAP9_BARSIZE_OFS+i*4,
-		grpci2_cfg_w32(priv, 0, 0, PCI_BASE_ADDRESS_0+i*4, pciadr);
+				bar_sz);
-		grpci2_cfg_w32(priv, 0, 0, capptr+CAP9_BAR_OFS+i*4, ahbadr);
+		grpci2_cfg_w32(priv, TGT, 0, PCI_BASE_ADDRESS_0+i*4, pciadr);
+		grpci2_cfg_w32(priv, TGT, 0, capptr+CAP9_BAR_OFS+i*4, ahbadr);
 		printk(KERN_INFO "        TGT BAR[%d]: 0x%08x (PCI)-> 0x%08x\n",
 			i, pciadr, ahbadr);
 	}
 
 	/* set as bus master and enable pci memory responses */
-	grpci2_cfg_r32(priv, 0, 0, PCI_COMMAND, &data);
+	grpci2_cfg_r32(priv, TGT, 0, PCI_COMMAND, &data);
 	data |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
-	grpci2_cfg_w32(priv, 0, 0, PCI_COMMAND, data);
+	grpci2_cfg_w32(priv, TGT, 0, PCI_COMMAND, data);
 
 	/* Enable Error respone (CPU-TRAP) on illegal memory access. */
 	REGSTORE(regs->ctrl, CTRL_ER | CTRL_PE);

arch/tile/configs/tilegx_defconfig

@@ -330,7 +330,6 @@ CONFIG_MD_RAID0=m
 CONFIG_MD_RAID1=m
 CONFIG_MD_RAID10=m
 CONFIG_MD_RAID456=m
-CONFIG_MULTICORE_RAID456=y
 CONFIG_MD_FAULTY=m
 CONFIG_BLK_DEV_DM=m
 CONFIG_DM_DEBUG=y

arch/tile/configs/tilepro_defconfig

@@ -324,7 +324,6 @@ CONFIG_MD_RAID0=m
 CONFIG_MD_RAID1=m
 CONFIG_MD_RAID10=m
 CONFIG_MD_RAID456=m
-CONFIG_MULTICORE_RAID456=y
 CONFIG_MD_FAULTY=m
 CONFIG_BLK_DEV_DM=m
 CONFIG_DM_DEBUG=y

arch/x86/include/asm/kprobes.h

@@ -77,6 +77,7 @@ struct arch_specific_insn {
 	 * a post_handler or break_handler).
 	 */
 	int boostable;
+	bool if_modifier;
 };
 
 struct arch_optimized_insn {

arch/x86/include/asm/kvm_host.h

@@ -414,8 +414,8 @@ struct kvm_vcpu_arch {
 	gpa_t time;
 	struct pvclock_vcpu_time_info hv_clock;
 	unsigned int hw_tsc_khz;
-	unsigned int time_offset;
+	struct gfn_to_hva_cache pv_time;
-	struct page *time_page;
+	bool pv_time_enabled;
 	/* set guest stopped flag in pvclock flags field */
 	bool pvclock_set_guest_stopped_request;
 

arch/x86/include/asm/xen/hypercall.h

@@ -382,14 +382,14 @@ HYPERVISOR_console_io(int cmd, int count, char *str)
 	return _hypercall3(int, console_io, cmd, count, str);
 }
 
-extern int __must_check HYPERVISOR_physdev_op_compat(int, void *);
+extern int __must_check xen_physdev_op_compat(int, void *);
 
 static inline int
 HYPERVISOR_physdev_op(int cmd, void *arg)
 {
 	int rc = _hypercall2(int, physdev_op, cmd, arg);
 	if (unlikely(rc == -ENOSYS))
-		rc = HYPERVISOR_physdev_op_compat(cmd, arg);
+		rc = xen_physdev_op_compat(cmd, arg);
 	return rc;
 }
 

arch/x86/include/uapi/asm/msr-index.h

@@ -44,6 +44,7 @@
 #define SNB_C1_AUTO_UNDEMOTE		(1UL << 27)
 #define SNB_C3_AUTO_UNDEMOTE		(1UL << 28)
 
+#define MSR_PLATFORM_INFO		0x000000ce
 #define MSR_MTRRcap			0x000000fe
 #define MSR_IA32_BBL_CR_CTL		0x00000119
 #define MSR_IA32_BBL_CR_CTL3		0x0000011e

arch/x86/kernel/cpu/perf_event_intel.c

@@ -101,6 +101,10 @@ static struct event_constraint intel_snb_event_constraints[] __read_mostly =
 	FIXED_EVENT_CONSTRAINT(0x00c0, 0), /* INST_RETIRED.ANY */
 	FIXED_EVENT_CONSTRAINT(0x003c, 1), /* CPU_CLK_UNHALTED.CORE */
 	FIXED_EVENT_CONSTRAINT(0x0300, 2), /* CPU_CLK_UNHALTED.REF */
+	INTEL_UEVENT_CONSTRAINT(0x04a3, 0xf), /* CYCLE_ACTIVITY.CYCLES_NO_DISPATCH */
+	INTEL_UEVENT_CONSTRAINT(0x05a3, 0xf), /* CYCLE_ACTIVITY.STALLS_L2_PENDING */
+	INTEL_UEVENT_CONSTRAINT(0x02a3, 0x4), /* CYCLE_ACTIVITY.CYCLES_L1D_PENDING */
+	INTEL_UEVENT_CONSTRAINT(0x06a3, 0x4), /* CYCLE_ACTIVITY.STALLS_L1D_PENDING */
 	INTEL_EVENT_CONSTRAINT(0x48, 0x4), /* L1D_PEND_MISS.PENDING */
 	INTEL_UEVENT_CONSTRAINT(0x01c0, 0x2), /* INST_RETIRED.PREC_DIST */
 	INTEL_EVENT_CONSTRAINT(0xcd, 0x8), /* MEM_TRANS_RETIRED.LOAD_LATENCY */

arch/x86/kernel/kprobes/core.c

@@ -375,6 +375,9 @@ static void __kprobes arch_copy_kprobe(struct kprobe *p)
 	else
 		p->ainsn.boostable = -1;
 
+	/* Check whether the instruction modifies Interrupt Flag or not */
+	p->ainsn.if_modifier = is_IF_modifier(p->ainsn.insn);
+
 	/* Also, displacement change doesn't affect the first byte */
 	p->opcode = p->ainsn.insn[0];
 }
@@ -434,7 +437,7 @@ static void __kprobes set_current_kprobe(struct kprobe *p, struct pt_regs *regs,
 	__this_cpu_write(current_kprobe, p);
 	kcb->kprobe_saved_flags = kcb->kprobe_old_flags
 		= (regs->flags & (X86_EFLAGS_TF | X86_EFLAGS_IF));
-	if (is_IF_modifier(p->ainsn.insn))
+	if (p->ainsn.if_modifier)
 		kcb->kprobe_saved_flags &= ~X86_EFLAGS_IF;
 }
 

arch/x86/kernel/microcode_intel_early.c

@@ -90,13 +90,13 @@ microcode_phys(struct microcode_intel **mc_saved_tmp,
 	struct microcode_intel ***mc_saved;
 
 	mc_saved = (struct microcode_intel ***)
-		   __pa_symbol(&mc_saved_data->mc_saved);
+		   __pa_nodebug(&mc_saved_data->mc_saved);
 	for (i = 0; i < mc_saved_data->mc_saved_count; i++) {
 		struct microcode_intel *p;
 
 		p = *(struct microcode_intel **)
-			__pa(mc_saved_data->mc_saved + i);
+			__pa_nodebug(mc_saved_data->mc_saved + i);
-		mc_saved_tmp[i] = (struct microcode_intel *)__pa(p);
+		mc_saved_tmp[i] = (struct microcode_intel *)__pa_nodebug(p);
 	}
 }
 #endif
@@ -562,7 +562,7 @@ scan_microcode(unsigned long start, unsigned long end,
 	struct cpio_data cd;
 	long offset = 0;
 #ifdef CONFIG_X86_32
-	char *p = (char *)__pa_symbol(ucode_name);
+	char *p = (char *)__pa_nodebug(ucode_name);
 #else
 	char *p = ucode_name;
 #endif
@@ -630,8 +630,8 @@ static void __cpuinit print_ucode(struct ucode_cpu_info *uci)
 	if (mc_intel == NULL)
 		return;
 
-	delay_ucode_info_p = (int *)__pa_symbol(&delay_ucode_info);
+	delay_ucode_info_p = (int *)__pa_nodebug(&delay_ucode_info);
-	current_mc_date_p = (int *)__pa_symbol(&current_mc_date);
+	current_mc_date_p = (int *)__pa_nodebug(&current_mc_date);
 
 	*delay_ucode_info_p = 1;
 	*current_mc_date_p = mc_intel->hdr.date;
@@ -659,8 +659,8 @@ static inline void __cpuinit print_ucode(struct ucode_cpu_info *uci)
 }
 #endif
 
-static int apply_microcode_early(struct mc_saved_data *mc_saved_data,
+static int __cpuinit apply_microcode_early(struct mc_saved_data *mc_saved_data,
-				 struct ucode_cpu_info *uci)
+					   struct ucode_cpu_info *uci)
 {
 	struct microcode_intel *mc_intel;
 	unsigned int val[2];
@@ -741,15 +741,15 @@ load_ucode_intel_bsp(void)
 #ifdef CONFIG_X86_32
 	struct boot_params *boot_params_p;
 
-	boot_params_p = (struct boot_params *)__pa_symbol(&boot_params);
+	boot_params_p = (struct boot_params *)__pa_nodebug(&boot_params);
 	ramdisk_image = boot_params_p->hdr.ramdisk_image;
 	ramdisk_size  = boot_params_p->hdr.ramdisk_size;
 	initrd_start_early = ramdisk_image;
 	initrd_end_early = initrd_start_early + ramdisk_size;
 
 	_load_ucode_intel_bsp(
-		(struct mc_saved_data *)__pa_symbol(&mc_saved_data),
+		(struct mc_saved_data *)__pa_nodebug(&mc_saved_data),
-		(unsigned long *)__pa_symbol(&mc_saved_in_initrd),
+		(unsigned long *)__pa_nodebug(&mc_saved_in_initrd),
 		initrd_start_early, initrd_end_early, &uci);
 #else
 	ramdisk_image = boot_params.hdr.ramdisk_image;
@@ -772,10 +772,10 @@ void __cpuinit load_ucode_intel_ap(void)
 	unsigned long *initrd_start_p;
 
 	mc_saved_in_initrd_p =
-		(unsigned long *)__pa_symbol(mc_saved_in_initrd);
+		(unsigned long *)__pa_nodebug(mc_saved_in_initrd);
-	mc_saved_data_p = (struct mc_saved_data *)__pa_symbol(&mc_saved_data);
+	mc_saved_data_p = (struct mc_saved_data *)__pa_nodebug(&mc_saved_data);
-	initrd_start_p = (unsigned long *)__pa_symbol(&initrd_start);
+	initrd_start_p = (unsigned long *)__pa_nodebug(&initrd_start);
-	initrd_start_addr = (unsigned long)__pa_symbol(*initrd_start_p);
+	initrd_start_addr = (unsigned long)__pa_nodebug(*initrd_start_p);
 #else
 	mc_saved_data_p = &mc_saved_data;
 	mc_saved_in_initrd_p = mc_saved_in_initrd;

arch/x86/kvm/x86.c

@@ -1406,25 +1406,15 @@ static int kvm_guest_time_update(struct kvm_vcpu *v)
 	unsigned long flags, this_tsc_khz;
 	struct kvm_vcpu_arch *vcpu = &v->arch;
 	struct kvm_arch *ka = &v->kvm->arch;
-	void *shared_kaddr;
 	s64 kernel_ns, max_kernel_ns;
 	u64 tsc_timestamp, host_tsc;
-	struct pvclock_vcpu_time_info *guest_hv_clock;
+	struct pvclock_vcpu_time_info guest_hv_clock;
 	u8 pvclock_flags;
 	bool use_master_clock;
 
 	kernel_ns = 0;
 	host_tsc = 0;
 
-	/* Keep irq disabled to prevent changes to the clock */
-	local_irq_save(flags);
-	this_tsc_khz = __get_cpu_var(cpu_tsc_khz);
-	if (unlikely(this_tsc_khz == 0)) {
-		local_irq_restore(flags);
-		kvm_make_request(KVM_REQ_CLOCK_UPDATE, v);
-		return 1;
-	}
-
 	/*
 	 * If the host uses TSC clock, then passthrough TSC as stable
 	 * to the guest.
@@ -1436,6 +1426,15 @@ static int kvm_guest_time_update(struct kvm_vcpu *v)
 		kernel_ns = ka->master_kernel_ns;
 	}
 	spin_unlock(&ka->pvclock_gtod_sync_lock);
+
+	/* Keep irq disabled to prevent changes to the clock */
+	local_irq_save(flags);
+	this_tsc_khz = __get_cpu_var(cpu_tsc_khz);
+	if (unlikely(this_tsc_khz == 0)) {
+		local_irq_restore(flags);
+		kvm_make_request(KVM_REQ_CLOCK_UPDATE, v);
+		return 1;
+	}
 	if (!use_master_clock) {
 		host_tsc = native_read_tsc();
 		kernel_ns = get_kernel_ns();
@@ -1463,7 +1462,7 @@ static int kvm_guest_time_update(struct kvm_vcpu *v)
 
 	local_irq_restore(flags);
 
-	if (!vcpu->time_page)
+	if (!vcpu->pv_time_enabled)
 		return 0;
 
 	/*
@@ -1525,12 +1524,12 @@ static int kvm_guest_time_update(struct kvm_vcpu *v)
 	 */
 	vcpu->hv_clock.version += 2;
 
-	shared_kaddr = kmap_atomic(vcpu->time_page);
+	if (unlikely(kvm_read_guest_cached(v->kvm, &vcpu->pv_time,
-
+		&guest_hv_clock, sizeof(guest_hv_clock))))
-	guest_hv_clock = shared_kaddr + vcpu->time_offset;
+		return 0;
 
 	/* retain PVCLOCK_GUEST_STOPPED if set in guest copy */
-	pvclock_flags = (guest_hv_clock->flags & PVCLOCK_GUEST_STOPPED);
+	pvclock_flags = (guest_hv_clock.flags & PVCLOCK_GUEST_STOPPED);
 
 	if (vcpu->pvclock_set_guest_stopped_request) {
 		pvclock_flags |= PVCLOCK_GUEST_STOPPED;
@@ -1543,12 +1542,9 @@ static int kvm_guest_time_update(struct kvm_vcpu *v)
 
 	vcpu->hv_clock.flags = pvclock_flags;
 
-	memcpy(shared_kaddr + vcpu->time_offset, &vcpu->hv_clock,
+	kvm_write_guest_cached(v->kvm, &vcpu->pv_time,
-	       sizeof(vcpu->hv_clock));
+				&vcpu->hv_clock,
-
+				sizeof(vcpu->hv_clock));
-	kunmap_atomic(shared_kaddr);
-
-	mark_page_dirty(v->kvm, vcpu->time >> PAGE_SHIFT);
 	return 0;
 }
 
@@ -1837,10 +1833,7 @@ static int kvm_pv_enable_async_pf(struct kvm_vcpu *vcpu, u64 data)
 
 static void kvmclock_reset(struct kvm_vcpu *vcpu)
 {
-	if (vcpu->arch.time_page) {
+	vcpu->arch.pv_time_enabled = false;
-		kvm_release_page_dirty(vcpu->arch.time_page);
-		vcpu->arch.time_page = NULL;
-	}
 }
 
 static void accumulate_steal_time(struct kvm_vcpu *vcpu)
@@ -1947,6 +1940,7 @@ int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 		break;
 	case MSR_KVM_SYSTEM_TIME_NEW:
 	case MSR_KVM_SYSTEM_TIME: {
+		u64 gpa_offset;
 		kvmclock_reset(vcpu);
 
 		vcpu->arch.time = data;
@@ -1956,14 +1950,17 @@ int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 		if (!(data & 1))
 			break;
 
-		/* ...but clean it before doing the actual write */
+		gpa_offset = data & ~(PAGE_MASK | 1);
-		vcpu->arch.time_offset = data & ~(PAGE_MASK | 1);
 
-		vcpu->arch.time_page =
+		/* Check that the address is 32-byte aligned. */
-				gfn_to_page(vcpu->kvm, data >> PAGE_SHIFT);
+		if (gpa_offset & (sizeof(struct pvclock_vcpu_time_info) - 1))
+			break;
 
-		if (is_error_page(vcpu->arch.time_page))
+		if (kvm_gfn_to_hva_cache_init(vcpu->kvm,
-			vcpu->arch.time_page = NULL;
+		     &vcpu->arch.pv_time, data & ~1ULL))
+			vcpu->arch.pv_time_enabled = false;
+		else
+			vcpu->arch.pv_time_enabled = true;
 
 		break;
 	}
@@ -2967,7 +2964,7 @@ static int kvm_vcpu_ioctl_x86_set_xcrs(struct kvm_vcpu *vcpu,
  */
 static int kvm_set_guest_paused(struct kvm_vcpu *vcpu)
 {
-	if (!vcpu->arch.time_page)
+	if (!vcpu->arch.pv_time_enabled)
 		return -EINVAL;
 	vcpu->arch.pvclock_set_guest_stopped_request = true;
 	kvm_make_request(KVM_REQ_CLOCK_UPDATE, vcpu);
@@ -6718,6 +6715,7 @@ int kvm_arch_vcpu_init(struct kvm_vcpu *vcpu)
 		goto fail_free_wbinvd_dirty_mask;
 
 	vcpu->arch.ia32_tsc_adjust_msr = 0x0;
+	vcpu->arch.pv_time_enabled = false;
 	kvm_async_pf_hash_reset(vcpu);
 	kvm_pmu_init(vcpu);
 

arch/x86/lib/usercopy_64.c

@@ -74,10 +74,10 @@ copy_user_handle_tail(char *to, char *from, unsigned len, unsigned zerorest)
 	char c;
 	unsigned zero_len;
 
-	for (; len; --len) {
+	for (; len; --len, to++) {
 		if (__get_user_nocheck(c, from++, sizeof(char)))
 			break;
-		if (__put_user_nocheck(c, to++, sizeof(char)))
+		if (__put_user_nocheck(c, to, sizeof(char)))
 			break;
 	}
 

arch/x86/xen/mmu.c

@@ -1467,8 +1467,6 @@ static void __init xen_write_cr3_init(unsigned long cr3)
 	__xen_write_cr3(true, cr3);
 
 	xen_mc_issue(PARAVIRT_LAZY_CPU);  /* interrupts restored */
-
-	pv_mmu_ops.write_cr3 = &xen_write_cr3;
 }
 #endif
 
@@ -2122,6 +2120,7 @@ static void __init xen_post_allocator_init(void)
 #endif
 
 #ifdef CONFIG_X86_64
+	pv_mmu_ops.write_cr3 = &xen_write_cr3;
 	SetPagePinned(virt_to_page(level3_user_vsyscall));
 #endif
 	xen_mark_init_mm_pinned();

block/blk-flush.c

@@ -444,7 +444,7 @@ int blkdev_issue_flush(struct block_device *bdev, gfp_t gfp_mask,
 	 * copied from blk_rq_pos(rq).
 	 */
 	if (error_sector)
-               *error_sector = bio->bi_sector;
+		*error_sector = bio->bi_sector;
 
 	if (!bio_flagged(bio, BIO_UPTODATE))
 		ret = -EIO;

block/partition-generic.c

@@ -257,6 +257,7 @@ void delete_partition(struct gendisk *disk, int partno)
 
 	hd_struct_put(part);
 }
+EXPORT_SYMBOL(delete_partition);
 
 static ssize_t whole_disk_show(struct device *dev,
 			       struct device_attribute *attr, char *buf)

drivers/acpi/apei/cper.c

@@ -405,7 +405,7 @@ int apei_estatus_check(const struct acpi_hest_generic_status *estatus)
 		return rc;
 	data_len = estatus->data_length;
 	gdata = (struct acpi_hest_generic_data *)(estatus + 1);
-	while (data_len > sizeof(*gdata)) {
+	while (data_len >= sizeof(*gdata)) {
 		gedata_len = gdata->error_data_length;
 		if (gedata_len > data_len - sizeof(*gdata))
 			return -EINVAL;

drivers/acpi/pci_root.c

@@ -646,6 +646,7 @@ static void handle_root_bridge_insertion(acpi_handle handle)
 
 static void handle_root_bridge_removal(struct acpi_device *device)
 {
+	acpi_status status;
 	struct acpi_eject_event *ej_event;
 
 	ej_event = kmalloc(sizeof(*ej_event), GFP_KERNEL);
@@ -661,7 +662,9 @@ static void handle_root_bridge_removal(struct acpi_device *device)
 	ej_event->device = device;
 	ej_event->event = ACPI_NOTIFY_EJECT_REQUEST;
 
-	acpi_bus_hot_remove_device(ej_event);
+	status = acpi_os_hotplug_execute(acpi_bus_hot_remove_device, ej_event);
+	if (ACPI_FAILURE(status))
+		kfree(ej_event);
 }
 
 static void _handle_hotplug_event_root(struct work_struct *work)
@@ -676,8 +679,9 @@ static void _handle_hotplug_event_root(struct work_struct *work)
 	handle = hp_work->handle;
 	type = hp_work->type;
 
-	root = acpi_pci_find_root(handle);
+	acpi_scan_lock_acquire();
 
+	root = acpi_pci_find_root(handle);
 	acpi_get_name(handle, ACPI_FULL_PATHNAME, &buffer);
 
 	switch (type) {
@@ -711,6 +715,7 @@ static void _handle_hotplug_event_root(struct work_struct *work)
 		break;
 	}
 
+	acpi_scan_lock_release();
 	kfree(hp_work); /* allocated in handle_hotplug_event_bridge */
 	kfree(buffer.pointer);
 }

drivers/acpi/sleep.c

@@ -193,6 +193,14 @@ static struct dmi_system_id __initdata acpisleep_dmi_table[] = {
 	},
 	{
 	.callback = init_nvs_nosave,
+	.ident = "Sony Vaio VGN-FW21M",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FW21M"),
+		},
+	},
+	{
+	.callback = init_nvs_nosave,
 	.ident = "Sony Vaio VPCEB17FX",
 	.matches = {
 		DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),

drivers/amba/tegra-ahb.c

@@ -158,7 +158,7 @@ int tegra_ahb_enable_smmu(struct device_node *dn)
 EXPORT_SYMBOL(tegra_ahb_enable_smmu);
 #endif
 
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_PM
 static int tegra_ahb_suspend(struct device *dev)
 {
 	int i;

drivers/ata/Kconfig

@@ -59,15 +59,16 @@ config ATA_ACPI
 	  option libata.noacpi=1
 
 config SATA_ZPODD
-	bool "SATA Zero Power ODD Support"
+	bool "SATA Zero Power Optical Disc Drive (ZPODD) support"
 	depends on ATA_ACPI
 	default n
 	help
-	  This option adds support for SATA ZPODD. It requires both
+	  This option adds support for SATA Zero Power Optical Disc
-	  ODD and the platform support, and if enabled, will automatically
+	  Drive (ZPODD). It requires both the ODD and the platform
-	  power on/off the ODD when certain condition is satisfied. This
+	  support, and if enabled, will automatically power on/off the
-	  does not impact user's experience of the ODD, only power is saved
+	  ODD when certain condition is satisfied. This does not impact
-	  when ODD is not in use(i.e. no disc inside).
+	  end user's experience of the ODD, only power is saved when
+	  the ODD is not in use (i.e. no disc inside).
 
 	  If unsure, say N.
 

drivers/ata/ahci.c

@@ -281,6 +281,8 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x1f37), board_ahci }, /* Avoton RAID */
 	{ PCI_VDEVICE(INTEL, 0x1f3e), board_ahci }, /* Avoton RAID */
 	{ PCI_VDEVICE(INTEL, 0x1f3f), board_ahci }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x2823), board_ahci }, /* Wellsburg RAID */
+	{ PCI_VDEVICE(INTEL, 0x2827), board_ahci }, /* Wellsburg RAID */
 	{ PCI_VDEVICE(INTEL, 0x8d02), board_ahci }, /* Wellsburg AHCI */
 	{ PCI_VDEVICE(INTEL, 0x8d04), board_ahci }, /* Wellsburg RAID */
 	{ PCI_VDEVICE(INTEL, 0x8d06), board_ahci }, /* Wellsburg RAID */

drivers/ata/ata_piix.c

@@ -1547,6 +1547,10 @@ static bool piix_broken_system_poweroff(struct pci_dev *pdev)
 
 static int prefer_ms_hyperv = 1;
 module_param(prefer_ms_hyperv, int, 0);
+MODULE_PARM_DESC(prefer_ms_hyperv,
+	"Prefer Hyper-V paravirtualization drivers instead of ATA, "
+	"0 - Use ATA drivers, "
+	"1 (Default) - Use the paravirtualization drivers.");
 
 static void piix_ignore_devices_quirk(struct ata_host *host)
 {

drivers/ata/libata-acpi.c

@@ -1027,7 +1027,7 @@ static void ata_acpi_register_power_resource(struct ata_device *dev)
 
 	handle = ata_dev_acpi_handle(dev);
 	if (handle)
-		acpi_dev_pm_remove_dependent(handle, &sdev->sdev_gendev);
+		acpi_dev_pm_add_dependent(handle, &sdev->sdev_gendev);
 }
 
 static void ata_acpi_unregister_power_resource(struct ata_device *dev)

drivers/ata/pata_samsung_cf.c

@@ -661,18 +661,7 @@ static struct platform_driver pata_s3c_driver = {
 	},
 };
 
-static int __init pata_s3c_init(void)
+module_platform_driver_probe(pata_s3c_driver, pata_s3c_probe);
-{
-	return platform_driver_probe(&pata_s3c_driver, pata_s3c_probe);
-}
-
-static void __exit pata_s3c_exit(void)
-{
-	platform_driver_unregister(&pata_s3c_driver);
-}
-
-module_init(pata_s3c_init);
-module_exit(pata_s3c_exit);
 
 MODULE_AUTHOR("Abhilash Kesavan, <a.kesavan@samsung.com>");
 MODULE_DESCRIPTION("low-level driver for Samsung PATA controller");

drivers/ata/sata_fsl.c

@@ -1511,8 +1511,7 @@ error_exit_with_cleanup:
 
 	if (hcr_base)
 		iounmap(hcr_base);
-	if (host_priv)
+	kfree(host_priv);
-		kfree(host_priv);
 
 	return retval;
 }