Merge commit 'v2.6.31-rc8' into next

This commit is contained in:
Dmitry Torokhov 2009-08-27 22:00:20 -07:00
commit 4b61bb575b
1284 changed files with 32589 additions and 18887 deletions

View File

@ -2006,6 +2006,9 @@ E: paul@laufernet.com
D: Soundblaster driver fixes, ISAPnP quirk
S: California, USA
N: Jonathan Layes
D: ARPD support
N: Tom Lees
E: tom@lpsg.demon.co.uk
W: http://www.lpsg.demon.co.uk/
@ -3802,6 +3805,9 @@ S: van Bronckhorststraat 12
S: 2612 XV Delft
S: The Netherlands
N: Thomas Woller
D: CS461x Cirrus Logic sound driver
N: David Woodhouse
E: dwmw2@infradead.org
D: JFFS2 file system, Memory Technology Device subsystem,

View File

@ -94,28 +94,37 @@ What: /sys/block/<disk>/queue/physical_block_size
Date: May 2009
Contact: Martin K. Petersen <martin.petersen@oracle.com>
Description:
This is the smallest unit the storage device can write
without resorting to read-modify-write operation. It is
usually the same as the logical block size but may be
bigger. One example is SATA drives with 4KB sectors
that expose a 512-byte logical block size to the
operating system.
This is the smallest unit a physical storage device can
write atomically. It is usually the same as the logical
block size but may be bigger. One example is SATA
drives with 4KB sectors that expose a 512-byte logical
block size to the operating system. For stacked block
devices the physical_block_size variable contains the
maximum physical_block_size of the component devices.
What: /sys/block/<disk>/queue/minimum_io_size
Date: April 2009
Contact: Martin K. Petersen <martin.petersen@oracle.com>
Description:
Storage devices may report a preferred minimum I/O size,
which is the smallest request the device can perform
without incurring a read-modify-write penalty. For disk
drives this is often the physical block size. For RAID
arrays it is often the stripe chunk size.
Storage devices may report a granularity or preferred
minimum I/O size which is the smallest request the
device can perform without incurring a performance
penalty. For disk drives this is often the physical
block size. For RAID arrays it is often the stripe
chunk size. A properly aligned multiple of
minimum_io_size is the preferred request size for
workloads where a high number of I/O operations is
desired.
What: /sys/block/<disk>/queue/optimal_io_size
Date: April 2009
Contact: Martin K. Petersen <martin.petersen@oracle.com>
Description:
Storage devices may report an optimal I/O size, which is
the device's preferred unit of receiving I/O. This is
rarely reported for disk drives. For RAID devices it is
usually the stripe width or the internal block size.
the device's preferred unit for sustained I/O. This is
rarely reported for disk drives. For RAID arrays it is
usually the stripe width or the internal track size. A
properly aligned multiple of optimal_io_size is the
preferred request size for workloads where sustained
throughput is desired. If no optimal I/O size is
reported this file contains 0.

View File

@ -449,8 +449,8 @@ printk(KERN_INFO "i = %u\n", i);
</para>
<programlisting>
__u32 ipaddress;
printk(KERN_INFO "my ip: %d.%d.%d.%d\n", NIPQUAD(ipaddress));
__be32 ipaddress;
printk(KERN_INFO "my ip: %pI4\n", &amp;ipaddress);
</programlisting>
<para>

View File

@ -21,6 +21,8 @@ ffff8000 ffffffff copy_user_page / clear_user_page use.
For SA11xx and Xscale, this is used to
setup a minicache mapping.
ffff4000 ffffffff cache aliasing on ARMv6 and later CPUs.
ffff1000 ffff7fff Reserved.
Platforms must not use this address range.

View File

@ -123,6 +123,9 @@ available from the same CVS repository.
There are user and developer mailing lists available through the v9fs project
on sourceforge (http://sourceforge.net/projects/v9fs).
A stand-alone version of the module (which should build for any 2.6 kernel)
is available via (http://github.com/ericvh/9p-sac/tree/master)
News and other information is maintained on SWiK (http://swik.net/v9fs).
Bug reports may be issued through the kernel.org bugzilla

View File

@ -23,16 +23,14 @@ it does support include:
(*) Security (currently only AFS kaserver and KerberosIV tickets).
(*) File reading.
(*) File reading and writing.
(*) Automounting.
(*) Local caching (via fscache).
It does not yet support the following AFS features:
(*) Write support.
(*) Local caching.
(*) pioctl() system call.
@ -56,7 +54,7 @@ They permit the debugging messages to be turned on dynamically by manipulating
the masks in the following files:
/sys/module/af_rxrpc/parameters/debug
/sys/module/afs/parameters/debug
/sys/module/kafs/parameters/debug
=====
@ -66,9 +64,9 @@ USAGE
When inserting the driver modules the root cell must be specified along with a
list of volume location server IP addresses:
insmod af_rxrpc.o
insmod rxkad.o
insmod kafs.o rootcell=cambridge.redhat.com:172.16.18.73:172.16.18.91
modprobe af_rxrpc
modprobe rxkad
modprobe kafs rootcell=cambridge.redhat.com:172.16.18.73:172.16.18.91
The first module is the AF_RXRPC network protocol driver. This provides the
RxRPC remote operation protocol and may also be accessed from userspace. See:
@ -81,7 +79,7 @@ is the actual filesystem driver for the AFS filesystem.
Once the module has been loaded, more modules can be added by the following
procedure:
echo add grand.central.org 18.7.14.88:128.2.191.224 >/proc/fs/afs/cells
echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 >/proc/fs/afs/cells
Where the parameters to the "add" command are the name of a cell and a list of
volume location servers within that cell, with the latter separated by colons.
@ -101,7 +99,7 @@ The name of the volume can be suffixes with ".backup" or ".readonly" to
specify connection to only volumes of those types.
The name of the cell is optional, and if not given during a mount, then the
named volume will be looked up in the cell specified during insmod.
named volume will be looked up in the cell specified during modprobe.
Additional cells can be added through /proc (see later section).
@ -163,14 +161,14 @@ THE CELL DATABASE
The filesystem maintains an internal database of all the cells it knows and the
IP addresses of the volume location servers for those cells. The cell to which
the system belongs is added to the database when insmod is performed by the
the system belongs is added to the database when modprobe is performed by the
"rootcell=" argument or, if compiled in, using a "kafs.rootcell=" argument on
the kernel command line.
Further cells can be added by commands similar to the following:
echo add CELLNAME VLADDR[:VLADDR][:VLADDR]... >/proc/fs/afs/cells
echo add grand.central.org 18.7.14.88:128.2.191.224 >/proc/fs/afs/cells
echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 >/proc/fs/afs/cells
No other cell database operations are available at this time.
@ -233,7 +231,7 @@ insmod /tmp/kafs.o rootcell=cambridge.redhat.com:172.16.18.91
mount -t afs \%root.afs. /afs
mount -t afs \%cambridge.redhat.com:root.cell. /afs/cambridge.redhat.com/
echo add grand.central.org 18.7.14.88:128.2.191.224 > /proc/fs/afs/cells
echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 > /proc/fs/afs/cells
mount -t afs "#grand.central.org:root.cell." /afs/grand.central.org/
mount -t afs "#grand.central.org:root.archive." /afs/grand.central.org/archive
mount -t afs "#grand.central.org:root.contrib." /afs/grand.central.org/contrib

View File

@ -1167,13 +1167,11 @@ CHAPTER 3: PER-PROCESS PARAMETERS
3.1 /proc/<pid>/oom_adj - Adjust the oom-killer score
------------------------------------------------------
This file can be used to adjust the score used to select which processes should
be killed in an out-of-memory situation. The oom_adj value is a characteristic
of the task's mm, so all threads that share an mm with pid will have the same
oom_adj value. A high value will increase the likelihood of this process being
killed by the oom-killer. Valid values are in the range -16 to +15 as
explained below and a special value of -17, which disables oom-killing
altogether for threads sharing pid's mm.
This file can be used to adjust the score used to select which processes
should be killed in an out-of-memory situation. Giving it a high score will
increase the likelihood of this process being killed by the oom-killer. Valid
values are in the range -16 to +15, plus the special value -17, which disables
oom-killing altogether for this process.
The process to be killed in an out-of-memory situation is selected among all others
based on its badness score. This value equals the original memory size of the process
@ -1187,9 +1185,6 @@ the parent's score if they do not share the same memory. Thus forking servers
are the prime candidates to be killed. Having only one 'hungry' child will make
parent less preferable than the child.
/proc/<pid>/oom_adj cannot be changed for kthreads since they are immune from
oom-killing already.
/proc/<pid>/oom_score shows process' current badness score.
The following heuristics are then applied:

View File

@ -23,7 +23,8 @@ interface.
Using sysfs
~~~~~~~~~~~
sysfs is always compiled in. You can access it by doing:
sysfs is always compiled in if CONFIG_SYSFS is defined. You can access
it by doing:
mount -t sysfs sysfs /sys

View File

@ -139,6 +139,7 @@ Code Seq# Include File Comments
'm' all linux/synclink.h conflict!
'm' 00-1F net/irda/irmod.h conflict!
'n' 00-7F linux/ncp_fs.h
'n' 80-8F linux/nilfs2_fs.h NILFS2
'n' E0-FF video/matrox.h matroxfb
'o' 00-1F fs/ocfs2/ocfs2_fs.h OCFS2
'o' 00-03 include/mtd/ubi-user.h conflict! (OCFS2 and UBI overlaps)

View File

@ -1115,6 +1115,10 @@ and is between 256 and 4096 characters. It is defined in the file
libata.dma=4 Compact Flash DMA only
Combinations also work, so libata.dma=3 enables DMA
for disks and CDROMs, but not CFs.
libata.ignore_hpa= [LIBATA] Ignore HPA limit
libata.ignore_hpa=0 keep BIOS limits (default)
libata.ignore_hpa=1 ignore limits, using full disk
libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
when set.

View File

@ -36,8 +36,6 @@ detailed description):
- Bluetooth enable and disable
- video output switching, expansion control
- ThinkLight on and off
- limited docking and undocking
- UltraBay eject
- CMOS/UCMS control
- LED control
- ACPI sounds
@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off".
It is impossible to know if the status returned through sysfs is valid.
Docking / undocking -- /proc/acpi/ibm/dock
------------------------------------------
Docking and undocking (e.g. with the X4 UltraBase) requires some
actions to be taken by the operating system to safely make or break
the electrical connections with the dock.
The docking feature of this driver generates the following ACPI events:
ibm/dock GDCK 00000003 00000001 -- eject request
ibm/dock GDCK 00000003 00000002 -- undocked
ibm/dock GDCK 00000000 00000003 -- docked
NOTE: These events will only be generated if the laptop was docked
when originally booted. This is due to the current lack of support for
hot plugging of devices in the Linux ACPI framework. If the laptop was
booted while not in the dock, the following message is shown in the
logs:
Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present
In this case, no dock-related events are generated but the dock and
undock commands described below still work. They can be executed
manually or triggered by Fn key combinations (see the example acpid
configuration files included in the driver tarball package available
on the web site).
When the eject request button on the dock is pressed, the first event
above is generated. The handler for this event should issue the
following command:
echo undock > /proc/acpi/ibm/dock
After the LED on the dock goes off, it is safe to eject the laptop.
Note: if you pressed this key by mistake, go ahead and eject the
laptop, then dock it back in. Otherwise, the dock may not function as
expected.
When the laptop is docked, the third event above is generated. The
handler for this event should issue the following command to fully
enable the dock:
echo dock > /proc/acpi/ibm/dock
The contents of the /proc/acpi/ibm/dock file shows the current status
of the dock, as provided by the ACPI framework.
The docking support in this driver does not take care of enabling or
disabling any other devices you may have attached to the dock. For
example, a CD drive plugged into the UltraBase needs to be disabled or
enabled separately. See the provided example acpid configuration files
for how this can be accomplished.
There is no support yet for PCI devices that may be attached to a
docking station, e.g. in the ThinkPad Dock II. The driver currently
does not recognize, enable or disable such devices. This means that
the only docking stations currently supported are the X-series
UltraBase docks and "dumb" port replicators like the Mini Dock (the
latter don't need any ACPI support, actually).
UltraBay eject -- /proc/acpi/ibm/bay
------------------------------------
Inserting or ejecting an UltraBay device requires some actions to be
taken by the operating system to safely make or break the electrical
connections with the device.
This feature generates the following ACPI events:
ibm/bay MSTR 00000003 00000000 -- eject request
ibm/bay MSTR 00000001 00000000 -- eject lever inserted
NOTE: These events will only be generated if the UltraBay was present
when the laptop was originally booted (on the X series, the UltraBay
is in the dock, so it may not be present if the laptop was undocked).
This is due to the current lack of support for hot plugging of devices
in the Linux ACPI framework. If the laptop was booted without the
UltraBay, the following message is shown in the logs:
Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present
In this case, no bay-related events are generated but the eject
command described below still works. It can be executed manually or
triggered by a hot key combination.
Sliding the eject lever generates the first event shown above. The
handler for this event should take whatever actions are necessary to
shut down the device in the UltraBay (e.g. call idectl), then issue
the following command:
echo eject > /proc/acpi/ibm/bay
After the LED on the UltraBay goes off, it is safe to pull out the
device.
When the eject lever is inserted, the second event above is
generated. The handler for this event should take whatever actions are
necessary to enable the UltraBay device (e.g. call idectl).
The contents of the /proc/acpi/ibm/bay file shows the current status
of the UltraBay, as provided by the ACPI framework.
EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use
this feature, you need to supply the experimental=1 parameter when
loading the module):
These models do not have a button near the UltraBay device to request
a hot eject but rather require the laptop to be put to sleep
(suspend-to-ram) before the bay device is ejected or inserted).
The sequence of steps to eject the device is as follows:
echo eject > /proc/acpi/ibm/bay
put the ThinkPad to sleep
remove the drive
resume from sleep
cat /proc/acpi/ibm/bay should show that the drive was removed
On the A3x, both the UltraBay 2000 and UltraBay Plus devices are
supported. Use "eject2" instead of "eject" for the second bay.
Note: the UltraBay eject support on the 600e/x, A22p and A3x is
EXPERIMENTAL and may not work as expected. USE WITH CAUTION!
CMOS/UCMS control
-----------------

File diff suppressed because it is too large Load Diff

View File

@ -30,9 +30,9 @@ State
The validator tracks lock-class usage history into 4n + 1 separate state bits:
- 'ever held in STATE context'
- 'ever head as readlock in STATE context'
- 'ever head with STATE enabled'
- 'ever head as readlock with STATE enabled'
- 'ever held as readlock in STATE context'
- 'ever held with STATE enabled'
- 'ever held as readlock with STATE enabled'
Where STATE can be either one of (kernel/lockdep_states.h)
- hardirq

View File

@ -101,6 +101,8 @@ card*/pcm*/xrun_debug
bit 0 = Enable XRUN/jiffies debug messages
bit 1 = Show stack trace at XRUN / jiffies check
bit 2 = Enable additional jiffies check
bit 3 = Log hwptr update at each period interrupt
bit 4 = Log hwptr update at each snd_pcm_update_hw_ptr()
When the bit 0 is set, the driver will show the messages to
kernel log when an xrun is detected. The debug message is
@ -117,6 +119,9 @@ card*/pcm*/xrun_debug
buggy) hardware that doesn't give smooth pointer updates.
This feature is enabled via the bit 2.
Bits 3 and 4 are for logging the hwptr records. Note that
these will give flood of kernel messages.
card*/pcm*/sub*/info
The general information of this PCM sub-stream.

View File

@ -66,7 +66,8 @@ On all - write a character to /proc/sysrq-trigger. e.g.:
'b' - Will immediately reboot the system without syncing or unmounting
your disks.
'c' - Will perform a kexec reboot in order to take a crashdump.
'c' - Will perform a system crash by a NULL pointer dereference.
A crashdump will be taken if configured.
'd' - Shows all locks that are held.
@ -141,8 +142,8 @@ useful when you want to exit a program that will not let you switch consoles.
re'B'oot is good when you're unable to shut down. But you should also 'S'ync
and 'U'mount first.
'C'rashdump can be used to manually trigger a crashdump when the system is hung.
The kernel needs to have been built with CONFIG_KEXEC enabled.
'C'rash can be used to manually trigger a crashdump when the system is hung.
Note that this just triggers a crash if there is no dump mechanism available.
'S'ync is great when your system is locked up, it allows you to sync your
disks and will certainly lessen the chance of data loss and fscking. Note

View File

@ -1,5 +1,5 @@
0 -> Unknown EM2800 video grabber (em2800) [eb1a:2800]
1 -> Unknown EM2750/28xx video grabber (em2820/em2840) [eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883]
1 -> Unknown EM2750/28xx video grabber (em2820/em2840) [eb1a:2710,eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883]
2 -> Terratec Cinergy 250 USB (em2820/em2840) [0ccd:0036]
3 -> Pinnacle PCTV USB 2 (em2820/em2840) [2304:0208]
4 -> Hauppauge WinTV USB 2 (em2820/em2840) [2040:4200,2040:4201]
@ -20,7 +20,7 @@
19 -> EM2860/SAA711X Reference Design (em2860)
20 -> AMD ATI TV Wonder HD 600 (em2880) [0438:b002]
21 -> eMPIA Technology, Inc. GrabBeeX+ Video Encoder (em2800) [eb1a:2801]
22 -> Unknown EM2750/EM2751 webcam grabber (em2750) [eb1a:2750,eb1a:2751]
22 -> EM2710/EM2750/EM2751 webcam grabber (em2750) [eb1a:2750,eb1a:2751]
23 -> Huaqi DLCW-130 (em2750)
24 -> D-Link DUB-T210 TV Tuner (em2820/em2840) [2001:f112]
25 -> Gadmei UTV310 (em2820/em2840)

View File

@ -153,8 +153,8 @@
152 -> Asus Tiger Rev:1.00 [1043:4857]
153 -> Kworld Plus TV Analog Lite PCI [17de:7128]
154 -> Avermedia AVerTV GO 007 FM Plus [1461:f31d]
155 -> Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid [0070:6706,0070:6708]
156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a]
155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid [0070:6706,0070:6708]
156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid [0070:6707,0070:6709,0070:670a]
157 -> Avermedia AVerTV Studio 507UA [1461:a11b]
158 -> AVerMedia Cardbus TV/Radio (E501R) [1461:b7e9]
159 -> Beholder BeholdTV 505 RDS [0000:505B]

View File

@ -44,7 +44,9 @@ zc3xx 0458:7007 Genius VideoCam V2
zc3xx 0458:700c Genius VideoCam V3
zc3xx 0458:700f Genius VideoCam Web V2
sonixj 0458:7025 Genius Eye 311Q
sn9c20x 0458:7029 Genius Look 320s
sonixj 0458:702e Genius Slim 310 NB
sn9c20x 045e:00f4 LifeCam VX-6000 (SN9C20x + OV9650)
sonixj 045e:00f5 MicroSoft VX3000
sonixj 045e:00f7 MicroSoft VX1000
ov519 045e:028c Micro$oft xbox cam
@ -282,6 +284,28 @@ sonixj 0c45:613a Microdia Sonix PC Camera
sonixj 0c45:613b Surfer SN-206
sonixj 0c45:613c Sonix Pccam168
sonixj 0c45:6143 Sonix Pccam168
sn9c20x 0c45:6240 PC Camera (SN9C201 + MT9M001)
sn9c20x 0c45:6242 PC Camera (SN9C201 + MT9M111)
sn9c20x 0c45:6248 PC Camera (SN9C201 + OV9655)
sn9c20x 0c45:624e PC Camera (SN9C201 + SOI968)
sn9c20x 0c45:624f PC Camera (SN9C201 + OV9650)
sn9c20x 0c45:6251 PC Camera (SN9C201 + OV9650)
sn9c20x 0c45:6253 PC Camera (SN9C201 + OV9650)
sn9c20x 0c45:6260 PC Camera (SN9C201 + OV7670)
sn9c20x 0c45:6270 PC Camera (SN9C201 + MT9V011/MT9V111/MT9V112)
sn9c20x 0c45:627b PC Camera (SN9C201 + OV7660)
sn9c20x 0c45:627c PC Camera (SN9C201 + HV7131R)
sn9c20x 0c45:627f PC Camera (SN9C201 + OV9650)
sn9c20x 0c45:6280 PC Camera (SN9C202 + MT9M001)
sn9c20x 0c45:6282 PC Camera (SN9C202 + MT9M111)
sn9c20x 0c45:6288 PC Camera (SN9C202 + OV9655)
sn9c20x 0c45:628e PC Camera (SN9C202 + SOI968)
sn9c20x 0c45:628f PC Camera (SN9C202 + OV9650)
sn9c20x 0c45:62a0 PC Camera (SN9C202 + OV7670)
sn9c20x 0c45:62b0 PC Camera (SN9C202 + MT9V011/MT9V111/MT9V112)
sn9c20x 0c45:62b3 PC Camera (SN9C202 + OV9655)
sn9c20x 0c45:62bb PC Camera (SN9C202 + OV7660)
sn9c20x 0c45:62bc PC Camera (SN9C202 + HV7131R)
sunplus 0d64:0303 Sunplus FashionCam DXG
etoms 102c:6151 Qcam Sangha CIF
etoms 102c:6251 Qcam xxxxxx VGA
@ -290,6 +314,7 @@ spca561 10fd:7e50 FlyCam Usb 100
zc3xx 10fd:8050 Typhoon Webshot II USB 300k
ov534 1415:2000 Sony HD Eye for PS3 (SLEH 00201)
pac207 145f:013a Trust WB-1300N
sn9c20x 145f:013d Trust WB-3600R
vc032x 15b8:6001 HP 2.0 Megapixel
vc032x 15b8:6002 HP 2.0 Megapixel rz406aa
spca501 1776:501c Arowana 300K CMOS Camera
@ -300,4 +325,11 @@ spca500 2899:012c Toptro Industrial
spca508 8086:0110 Intel Easy PC Camera
spca500 8086:0630 Intel Pocket PC Camera
spca506 99fa:8988 Grandtec V.cap
sn9c20x a168:0610 Dino-Lite Digital Microscope (SN9C201 + HV7131R)
sn9c20x a168:0611 Dino-Lite Digital Microscope (SN9C201 + HV7131R)
sn9c20x a168:0613 Dino-Lite Digital Microscope (SN9C201 + HV7131R)
sn9c20x a168:0618 Dino-Lite Digital Microscope (SN9C201 + HV7131R)
sn9c20x a168:0614 Dino-Lite Digital Microscope (SN9C201 + MT9M111)
sn9c20x a168:0615 Dino-Lite Digital Microscope (SN9C201 + MT9M111)
sn9c20x a168:0617 Dino-Lite Digital Microscope (SN9C201 + MT9M111)
spca561 abcd:cdee Petcam

File diff suppressed because it is too large Load Diff

View File

@ -1,7 +1,7 @@
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 31
EXTRAVERSION = -rc4
EXTRAVERSION = -rc8
NAME = Man-Eating Seals of Antiquity
# *DOCUMENTATION*

View File

@ -15,7 +15,10 @@ worry too much about getting the wrong person. If you are unsure send it
to the person responsible for the code relevant to what you were doing.
If it occurs repeatably try and describe how to recreate it. That is
worth even more than the oops itself. The list of maintainers and
mailing lists is in the MAINTAINERS file in this directory.
mailing lists is in the MAINTAINERS file in this directory. If you
know the file name that causes the problem you can use the following
command in this directory to find some of the maintainers of that file:
perl scripts/get_maintainer.pl -f <filename>
If it is a security bug, please copy the Security Contact listed
in the MAINTAINERS file. They can help coordinate bugfix and disclosure.

View File

@ -9,7 +9,7 @@
#include <asm-generic/tlb.h>
#define __pte_free_tlb(tlb, pte) pte_free((tlb)->mm, pte)
#define __pmd_free_tlb(tlb, pmd) pmd_free((tlb)->mm, pmd)
#define __pte_free_tlb(tlb, pte, address) pte_free((tlb)->mm, pte)
#define __pmd_free_tlb(tlb, pmd, address) pmd_free((tlb)->mm, pmd)
#endif

View File

@ -29,7 +29,6 @@ unsigned int __machine_arch_type;
static void putstr(const char *ptr);
#include <linux/compiler.h>
#include <mach/uncompress.h>
#ifdef CONFIG_DEBUG_ICEDCC

View File

@ -17,6 +17,7 @@
#include <linux/err.h>
#include <linux/string.h>
#include <linux/mutex.h>
#include <linux/clk.h>
#include <asm/clkdev.h>
#include <mach/clkdev.h>

View File

@ -629,7 +629,7 @@ CONFIG_SCSI_LOWLEVEL=y
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SIL24 is not set
CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set

View File

@ -1,15 +1,15 @@
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.30-rc1
# Wed Apr 8 10:18:06 2009
# Linux kernel version: 2.6.31-rc4
# Fri Jul 24 16:08:06 2009
#
CONFIG_ARM=y
CONFIG_HAVE_PWM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_MMU=y
# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_MTD_XIP=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y
#
# General setup
@ -85,7 +84,12 @@ CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
#
# Performance Counters
#
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_COMPAT_BRK is not set
CONFIG_SLAB=y
# CONFIG_SLUB is not set
@ -99,6 +103,12 @@ CONFIG_KPROBES=y
CONFIG_KRETPROBES=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_CLK=y
#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
@ -111,7 +121,7 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
# CONFIG_LBD is not set
CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
@ -138,13 +148,14 @@ CONFIG_FREEZER=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
@ -153,25 +164,25 @@ CONFIG_FREEZER=y
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_W90X900 is not set
#
# Freescale MXC Implementations
@ -188,6 +199,8 @@ CONFIG_MACH_MX27=y
CONFIG_MACH_MX27ADS=y
CONFIG_MACH_PCM038=y
CONFIG_MACH_PCM970_BASEBOARD=y
CONFIG_MACH_MX27_3DS=y
CONFIG_MACH_MX27LITE=y
CONFIG_MXC_IRQ_PRIOR=y
CONFIG_MXC_PWM=y
@ -213,7 +226,6 @@ CONFIG_ARM_THUMB=y
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
# CONFIG_OUTER_CACHE is not set
CONFIG_COMMON_CLKDEV=y
#
@ -238,7 +250,6 @@ CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
CONFIG_ARCH_FLATMEM_HAS_HOLES=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_HIGHMEM is not set
@ -253,10 +264,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
CONFIG_UNEVICTABLE_LRU=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ALIGNMENT_TRAP=y
# CONFIG_UACCESS_WITH_MEMCPY is not set
#
# Boot options
@ -361,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
@ -474,7 +487,16 @@ CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
# CONFIG_MTD_NAND is not set
CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
# CONFIG_MTD_NAND_GPIO is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
CONFIG_MTD_NAND_MXC=y
# CONFIG_MTD_ONENAND is not set
#
@ -485,7 +507,15 @@ CONFIG_MTD_PHYSMAP=y
#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_RESERVE=1
# CONFIG_MTD_UBI_GLUEBI is not set
#
# UBI debugging options
#
# CONFIG_MTD_UBI_DEBUG is not set
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
@ -494,7 +524,21 @@ CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MISC_DEVICES is not set
# CONFIG_MG_DISK is not set
CONFIG_MISC_DEVICES=y
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_ISL29003 is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
CONFIG_EEPROM_AT24=y
# CONFIG_EEPROM_AT25 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@ -508,7 +552,6 @@ CONFIG_HAVE_IDE=y
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
@ -534,6 +577,8 @@ CONFIG_NET_ETHERNET=y
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
# CONFIG_KS8851 is not set
CONFIG_FEC=y
# CONFIG_FEC2 is not set
# CONFIG_NETDEV_1000 is not set
@ -580,6 +625,11 @@ CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_ADS7846 is not set
# CONFIG_TOUCHSCREEN_AD7877 is not set
# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
# CONFIG_TOUCHSCREEN_AD7879 is not set
# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
@ -592,6 +642,7 @@ CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
# CONFIG_TOUCHSCREEN_W90X900 is not set
# CONFIG_INPUT_MISC is not set
#
@ -644,6 +695,7 @@ CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
CONFIG_I2C_IMX=y
# CONFIG_I2C_OCORES is not set
@ -668,7 +720,6 @@ CONFIG_I2C_IMX=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
@ -719,6 +770,7 @@ CONFIG_W1=y
#
# CONFIG_W1_MASTER_DS2482 is not set
CONFIG_W1_MASTER_MXC=y
# CONFIG_W1_MASTER_DS1WM is not set
# CONFIG_W1_MASTER_GPIO is not set
#
@ -753,54 +805,16 @@ CONFIG_SSB_POSSIBLE=y
# CONFIG_TPS65010 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
#
# Multimedia core support
#
CONFIG_VIDEO_DEV=y
CONFIG_VIDEO_V4L2_COMMON=y
CONFIG_VIDEO_ALLOW_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
# CONFIG_DVB_CORE is not set
CONFIG_VIDEO_MEDIA=y
#
# Multimedia drivers
#
# CONFIG_MEDIA_ATTACH is not set
CONFIG_MEDIA_TUNER=y
# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
CONFIG_MEDIA_TUNER_SIMPLE=y
CONFIG_MEDIA_TUNER_TDA8290=y
CONFIG_MEDIA_TUNER_TDA9887=y
CONFIG_MEDIA_TUNER_TEA5761=y
CONFIG_MEDIA_TUNER_TEA5767=y
CONFIG_MEDIA_TUNER_MT20XX=y
CONFIG_MEDIA_TUNER_XC2028=y
CONFIG_MEDIA_TUNER_XC5000=y
CONFIG_MEDIA_TUNER_MC44S803=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_SOC_CAMERA is not set
# CONFIG_RADIO_ADAPTERS is not set
# CONFIG_DAB is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
@ -917,6 +931,7 @@ CONFIG_RTC_DRV_PCF8563=y
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
@ -962,12 +977,15 @@ CONFIG_RTC_DRV_PCF8563=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY is not set
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
@ -1021,6 +1039,12 @@ CONFIG_JFFS2_ZLIB=y
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_UBIFS_FS=y
# CONFIG_UBIFS_FS_XATTR is not set
# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
# CONFIG_UBIFS_FS_DEBUG is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
@ -1119,25 +1143,11 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
#
# Tracers
#
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_CONTEXT_SWITCH_TRACER is not set
# CONFIG_EVENT_TRACER is not set
# CONFIG_BOOT_TRACER is not set
# CONFIG_TRACE_BRANCH_PROFILING is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_KMEMTRACE is not set
# CONFIG_WORKQUEUE_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_FTRACE_STARTUP_TEST is not set
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
@ -1151,16 +1161,104 @@ CONFIG_ARM_UNWIND=y
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_CRYPTO is not set
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_TEST is not set
#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set
#
# Block modes
#
# CONFIG_CRYPTO_CBC is not set
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set
#
# Hash modes
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set
#
# Ciphers
#
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_TWOFISH is not set
#
# Compression
#
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_ZLIB is not set
CONFIG_CRYPTO_LZO=y
#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
CONFIG_BINARY_PRINTF=y
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_RATIONAL=y
CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC16=y
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
@ -1168,6 +1266,8 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y

View File

@ -1,15 +1,15 @@
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.30-rc1
# Wed Apr 8 11:06:37 2009
# Linux kernel version: 2.6.31-rc4
# Tue Jul 28 14:11:34 2009
#
CONFIG_ARM=y
CONFIG_HAVE_PWM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_MMU=y
# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_MTD_XIP=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_CONSTRUCTORS=y
#
# General setup
@ -86,7 +85,12 @@ CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
#
# Performance Counters
#
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
@ -97,6 +101,11 @@ CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_CLK=y
#
# GCOV-based kernel profiling
#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
@ -109,7 +118,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
# CONFIG_LBD is not set
CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
@ -136,13 +145,14 @@ CONFIG_FREEZER=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
@ -151,25 +161,25 @@ CONFIG_FREEZER=y
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
CONFIG_ARCH_MXC=y
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_W90X900 is not set
#
# Freescale MXC Implementations
@ -178,6 +188,7 @@ CONFIG_ARCH_MXC=y
# CONFIG_ARCH_MX2 is not set
CONFIG_ARCH_MX3=y
CONFIG_ARCH_MX31=y
CONFIG_ARCH_MX35=y
#
# MX3 platforms:
@ -185,12 +196,19 @@ CONFIG_ARCH_MX31=y
CONFIG_MACH_MX31ADS=y
CONFIG_MACH_MX31ADS_WM1133_EV1=y
CONFIG_MACH_PCM037=y
CONFIG_MACH_PCM037_EET=y
CONFIG_MACH_MX31LITE=y
CONFIG_MACH_MX31_3DS=y
CONFIG_MACH_MX31MOBOARD=y
CONFIG_MACH_MX31LILLY=y
CONFIG_MACH_QONG=y
CONFIG_MACH_PCM043=y
CONFIG_MACH_ARMADILLO5X0=y
CONFIG_MACH_MX35_3DS=y
CONFIG_MXC_IRQ_PRIOR=y
CONFIG_MXC_PWM=y
CONFIG_ARCH_HAS_RNGA=y
CONFIG_ARCH_MXC_IOMUX_V3=y
#
# Processor Type
@ -218,6 +236,7 @@ CONFIG_ARM_THUMB=y
# CONFIG_CPU_BPREDICT_DISABLE is not set
CONFIG_OUTER_CACHE=y
CONFIG_CACHE_L2X0=y
# CONFIG_ARM_ERRATA_411920 is not set
CONFIG_COMMON_CLKDEV=y
#
@ -242,7 +261,6 @@ CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
CONFIG_ARCH_FLATMEM_HAS_HOLES=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_HIGHMEM is not set
@ -257,10 +275,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
CONFIG_UNEVICTABLE_LRU=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ALIGNMENT_TRAP=y
# CONFIG_UACCESS_WITH_MEMCPY is not set
#
# Boot options
@ -362,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
@ -465,7 +485,16 @@ CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
# CONFIG_MTD_NAND is not set
CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
# CONFIG_MTD_NAND_GPIO is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
CONFIG_MTD_NAND_MXC=y
# CONFIG_MTD_ONENAND is not set
#
@ -476,10 +505,30 @@ CONFIG_MTD_PHYSMAP=y
#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_RESERVE=1
# CONFIG_MTD_UBI_GLUEBI is not set
#
# UBI debugging options
#
# CONFIG_MTD_UBI_DEBUG is not set
# CONFIG_PARPORT is not set
# CONFIG_BLK_DEV is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_MISC_DEVICES=y
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_ISL29003 is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
CONFIG_EEPROM_AT24=y
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@ -493,7 +542,6 @@ CONFIG_HAVE_IDE=y
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
@ -528,7 +576,7 @@ CONFIG_MII=y
# CONFIG_ETHOC is not set
# CONFIG_SMC911X is not set
CONFIG_SMSC911X=y
# CONFIG_DNET is not set
CONFIG_DNET=y
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
@ -537,8 +585,10 @@ CONFIG_SMSC911X=y
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
CONFIG_CS89x0=y
CONFIG_CS89x0_NONISA_IRQ=y
# CONFIG_CS89x0 is not set
# CONFIG_KS8842 is not set
CONFIG_FEC=y
# CONFIG_FEC2 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
@ -609,6 +659,7 @@ CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
CONFIG_I2C_IMX=y
# CONFIG_I2C_OCORES is not set
@ -633,7 +684,6 @@ CONFIG_I2C_IMX=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
@ -669,6 +719,7 @@ CONFIG_W1=y
#
# CONFIG_W1_MASTER_DS2482 is not set
CONFIG_W1_MASTER_MXC=y
# CONFIG_W1_MASTER_DS1WM is not set
# CONFIG_W1_MASTER_GPIO is not set
#
@ -703,6 +754,8 @@ CONFIG_SSB_POSSIBLE=y
# CONFIG_TPS65010 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
@ -711,10 +764,8 @@ CONFIG_MFD_WM8350_CONFIG_MODE_0=y
CONFIG_MFD_WM8352_CONFIG_MODE_0=y
CONFIG_MFD_WM8350_I2C=y
# CONFIG_MFD_PCF50633 is not set
#
# Multimedia devices
#
# CONFIG_AB3100_CORE is not set
CONFIG_MEDIA_SUPPORT=y
#
# Multimedia core support
@ -758,8 +809,10 @@ CONFIG_SOC_CAMERA_MT9T031=y
CONFIG_SOC_CAMERA_MT9V022=y
CONFIG_SOC_CAMERA_TW9910=y
# CONFIG_SOC_CAMERA_PLATFORM is not set
# CONFIG_SOC_CAMERA_OV772X is not set
CONFIG_SOC_CAMERA_OV772X=y
CONFIG_MX3_VIDEO=y
CONFIG_VIDEO_MX3=y
# CONFIG_VIDEO_SH_MOBILE_CEU is not set
# CONFIG_RADIO_ADAPTERS is not set
# CONFIG_DAB is not set
@ -847,8 +900,11 @@ CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
# CONFIG_REGULATOR_BQ24022 is not set
# CONFIG_REGULATOR_MAX1586 is not set
CONFIG_REGULATOR_WM8350=y
# CONFIG_REGULATOR_LP3971 is not set
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
@ -861,10 +917,12 @@ CONFIG_REGULATOR_WM8350=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
@ -921,6 +979,12 @@ CONFIG_JFFS2_ZLIB=y
# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_UBIFS_FS=y
# CONFIG_UBIFS_FS_XATTR is not set
# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
# CONFIG_UBIFS_FS_DEBUG is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
@ -937,6 +1001,7 @@ CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
@ -979,22 +1044,7 @@ CONFIG_FRAME_WARN=1024
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_TRACING_SUPPORT=y
#
# Tracers
#
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_CONTEXT_SWITCH_TRACER is not set
# CONFIG_EVENT_TRACER is not set
# CONFIG_BOOT_TRACER is not set
# CONFIG_TRACE_BRANCH_PROFILING is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_KMEMTRACE is not set
# CONFIG_WORKQUEUE_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_FTRACE is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_ARM_UNWIND=y
@ -1094,9 +1144,9 @@ CONFIG_CRYPTO_DES=y
#
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_LZO=y
#
# Random Number Generation
@ -1109,9 +1159,10 @@ CONFIG_CRYPTO_HW=y
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_RATIONAL=y
CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC16=y
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
@ -1119,6 +1170,8 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y

View File

@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m
CONFIG_USB_OTG_UTILS=y
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_ISP1301_OMAP is not set
CONFIG_TWL4030_USB=y
# CONFIG_TWL4030_USB is not set
# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set

View File

@ -282,7 +282,7 @@ CONFIG_ALIGNMENT_TRAP=y
#
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0"
CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0 console=ttyS2,115200n8"
# CONFIG_XIP_KERNEL is not set
# CONFIG_KEXEC is not set
@ -1354,7 +1354,7 @@ CONFIG_USB_OTG_UTILS=y
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_ISP1301_OMAP is not set
CONFIG_TWL4030_USB=y
CONFIG_MMC=m
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
@ -1449,7 +1449,8 @@ CONFIG_RTC_DRV_TWL4030=m
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
# CONFIG_REGULATOR is not set
CONFIG_REGULATOR=y
CONFIG_REGULATOR_TWL4030=y
# CONFIG_UIO is not set
# CONFIG_STAGING is not set

View File

@ -159,8 +159,6 @@ static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr)
#else /* ARM_ARCH_6 */
#include <asm/system.h>
#ifdef CONFIG_SMP
#error SMP not supported on pre-ARMv6 CPUs
#endif

View File

@ -201,7 +201,8 @@ static struct tagtable __tagtable_##fn __tag = { tag, fn }
struct membank {
unsigned long start;
unsigned long size;
int node;
unsigned short node;
unsigned short highmem;
};
struct meminfo {

View File

@ -102,8 +102,8 @@ tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
}
#define tlb_remove_page(tlb,page) free_page_and_swap_cache(page)
#define pte_free_tlb(tlb, ptep) pte_free((tlb)->mm, ptep)
#define pmd_free_tlb(tlb, pmdp) pmd_free((tlb)->mm, pmdp)
#define pte_free_tlb(tlb, ptep, addr) pte_free((tlb)->mm, ptep)
#define pmd_free_tlb(tlb, pmdp, addr) pmd_free((tlb)->mm, pmdp)
#define tlb_migrate_finish(mm) do { } while (0)

View File

@ -148,7 +148,7 @@ trace:
sub r0, r0, #MCOUNT_INSN_SIZE
mov lr, pc
mov pc, r2
mov lr, r1 @ restore lr
ldr lr, [fp, #-4] @ restore lr
ldmia sp!, {r0-r3, pc}
#endif /* CONFIG_DYNAMIC_FTRACE */

View File

@ -133,7 +133,7 @@ sys_sigaction(int sig, const struct old_sigaction __user *act,
}
#ifdef CONFIG_CRUNCH
static int preserve_crunch_context(struct crunch_sigframe *frame)
static int preserve_crunch_context(struct crunch_sigframe __user *frame)
{
char kbuf[sizeof(*frame) + 8];
struct crunch_sigframe *kframe;
@ -146,7 +146,7 @@ static int preserve_crunch_context(struct crunch_sigframe *frame)
return __copy_to_user(frame, kframe, sizeof(*frame));
}
static int restore_crunch_context(struct crunch_sigframe *frame)
static int restore_crunch_context(struct crunch_sigframe __user *frame)
{
char kbuf[sizeof(*frame) + 8];
struct crunch_sigframe *kframe;

View File

@ -0,0 +1,102 @@
/*
* Header file for the Atmel AHB DMA Controller driver
*
* Copyright (C) 2008 Atmel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef AT_HDMAC_H
#define AT_HDMAC_H
#include <linux/dmaengine.h>
/**
* struct at_dma_platform_data - Controller configuration parameters
* @nr_channels: Number of channels supported by hardware (max 8)
* @cap_mask: dma_capability flags supported by the platform
*/
struct at_dma_platform_data {
unsigned int nr_channels;
dma_cap_mask_t cap_mask;
};
/**
* enum at_dma_slave_width - DMA slave register access width.
* @AT_DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses
* @AT_DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses
* @AT_DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses
*/
enum at_dma_slave_width {
AT_DMA_SLAVE_WIDTH_8BIT = 0,
AT_DMA_SLAVE_WIDTH_16BIT,
AT_DMA_SLAVE_WIDTH_32BIT,
};
/**
* struct at_dma_slave - Controller-specific information about a slave
* @dma_dev: required DMA master device
* @tx_reg: physical address of data register used for
* memory-to-peripheral transfers
* @rx_reg: physical address of data register used for
* peripheral-to-memory transfers
* @reg_width: peripheral register width
* @cfg: Platform-specific initializer for the CFG register
* @ctrla: Platform-specific initializer for the CTRLA register
*/
struct at_dma_slave {
struct device *dma_dev;
dma_addr_t tx_reg;
dma_addr_t rx_reg;
enum at_dma_slave_width reg_width;
u32 cfg;
u32 ctrla;
};
/* Platform-configurable bits in CFG */
#define ATC_SRC_PER(h) (0xFU & (h)) /* Channel src rq associated with periph handshaking ifc h */
#define ATC_DST_PER(h) ((0xFU & (h)) << 4) /* Channel dst rq associated with periph handshaking ifc h */
#define ATC_SRC_REP (0x1 << 8) /* Source Replay Mod */
#define ATC_SRC_H2SEL (0x1 << 9) /* Source Handshaking Mod */
#define ATC_SRC_H2SEL_SW (0x0 << 9)
#define ATC_SRC_H2SEL_HW (0x1 << 9)
#define ATC_DST_REP (0x1 << 12) /* Destination Replay Mod */
#define ATC_DST_H2SEL (0x1 << 13) /* Destination Handshaking Mod */
#define ATC_DST_H2SEL_SW (0x0 << 13)
#define ATC_DST_H2SEL_HW (0x1 << 13)
#define ATC_SOD (0x1 << 16) /* Stop On Done */
#define ATC_LOCK_IF (0x1 << 20) /* Interface Lock */
#define ATC_LOCK_B (0x1 << 21) /* AHB Bus Lock */
#define ATC_LOCK_IF_L (0x1 << 22) /* Master Interface Arbiter Lock */
#define ATC_LOCK_IF_L_CHUNK (0x0 << 22)
#define ATC_LOCK_IF_L_BUFFER (0x1 << 22)
#define ATC_AHB_PROT_MASK (0x7 << 24) /* AHB Protection */
#define ATC_FIFOCFG_MASK (0x3 << 28) /* FIFO Request Configuration */
#define ATC_FIFOCFG_LARGESTBURST (0x0 << 28)
#define ATC_FIFOCFG_HALFFIFO (0x1 << 28)
#define ATC_FIFOCFG_ENOUGHSPACE (0x2 << 28)
/* Platform-configurable bits in CTRLA */
#define ATC_SCSIZE_MASK (0x7 << 16) /* Source Chunk Transfer Size */
#define ATC_SCSIZE_1 (0x0 << 16)
#define ATC_SCSIZE_4 (0x1 << 16)
#define ATC_SCSIZE_8 (0x2 << 16)
#define ATC_SCSIZE_16 (0x3 << 16)
#define ATC_SCSIZE_32 (0x4 << 16)
#define ATC_SCSIZE_64 (0x5 << 16)
#define ATC_SCSIZE_128 (0x6 << 16)
#define ATC_SCSIZE_256 (0x7 << 16)
#define ATC_DCSIZE_MASK (0x7 << 20) /* Destination Chunk Transfer Size */
#define ATC_DCSIZE_1 (0x0 << 20)
#define ATC_DCSIZE_4 (0x1 << 20)
#define ATC_DCSIZE_8 (0x2 << 20)
#define ATC_DCSIZE_16 (0x3 << 20)
#define ATC_DCSIZE_32 (0x4 << 20)
#define ATC_DCSIZE_64 (0x5 << 20)
#define ATC_DCSIZE_128 (0x6 << 20)
#define ATC_DCSIZE_256 (0x7 << 20)
#endif /* AT_HDMAC_H */

View File

@ -37,7 +37,6 @@
#include <mach/serial.h>
#include <mach/nand.h>
#include <mach/mmc.h>
#include <mach/common.h>
#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000
#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000

View File

@ -36,7 +36,6 @@
#include <mach/serial.h>
#include <mach/nand.h>
#include <mach/mmc.h>
#include <mach/common.h>
#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000
#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000

View File

@ -45,7 +45,6 @@
#include <mach/nand.h>
#include <mach/mmc.h>
#include <mach/emac.h>
#include <mach/common.h>
#define DM644X_EVM_PHY_MASK (0x2)
#define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */

View File

@ -47,7 +47,6 @@
#include <mach/i2c.h>
#include <mach/mmc.h>
#include <mach/emac.h>
#include <mach/common.h>
#define DM646X_EVM_PHY_MASK (0x2)
#define DM646X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */

View File

@ -52,7 +52,6 @@
#include <mach/serial.h>
#include <mach/psc.h>
#include <mach/mux.h>
#include <mach/common.h>
#define SFFSDR_PHY_MASK (0x2)
#define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */

View File

@ -41,9 +41,6 @@
#define TS72XX_OPTIONS2_TS9420_BOOT 0x02
#define TS72XX_NOR_PHYS_BASE 0x60000000
#define TS72XX_NOR2_PHYS_BASE 0x62000000
#define TS72XX_NAND1_DATA_PHYS_BASE 0x60000000
#define TS72XX_NAND2_DATA_PHYS_BASE 0x70000000
#define TS72XX_NAND_DATA_VIRT_BASE 0xfebfc000

View File

@ -112,13 +112,16 @@ static void __init ts72xx_map_io(void)
}
}
/*************************************************************************
* NOR flash (TS-7200 only)
*************************************************************************/
static struct physmap_flash_data ts72xx_flash_data = {
.width = 1,
.width = 2,
};
static struct resource ts72xx_flash_resource = {
.start = TS72XX_NOR_PHYS_BASE,
.end = TS72XX_NOR_PHYS_BASE + SZ_16M - 1,
.start = EP93XX_CS6_PHYS_BASE,
.end = EP93XX_CS6_PHYS_BASE + SZ_16M - 1,
.flags = IORESOURCE_MEM,
};
@ -132,6 +135,12 @@ static struct platform_device ts72xx_flash = {
.resource = &ts72xx_flash_resource,
};
static void __init ts72xx_register_flash(void)
{
if (board_is_ts7200())
platform_device_register(&ts72xx_flash);
}
static unsigned char ts72xx_rtc_readbyte(unsigned long addr)
{
__raw_writeb(addr, TS72XX_RTC_INDEX_VIRT_BASE);
@ -165,8 +174,7 @@ static struct ep93xx_eth_data ts72xx_eth_data = {
static void __init ts72xx_init_machine(void)
{
ep93xx_init_devices();
if (board_is_ts7200())
platform_device_register(&ts72xx_flash);
ts72xx_register_flash();
platform_device_register(&ts72xx_rtc_device);
ep93xx_register_eth(&ts72xx_eth_data, 1);

View File

@ -17,7 +17,7 @@
#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffff0000
#define IO_SPACE_LIMIT 0x0000ffff
extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);

View File

@ -206,6 +206,15 @@ static void __init qnap_ts219_init(void)
}
static int __init ts219_pci_init(void)
{
if (machine_is_ts219())
kirkwood_pcie_init();
return 0;
}
subsys_initcall(ts219_pci_init);
MACHINE_START(TS219, "QNAP TS-119/TS-219")
/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
.phys_io = KIRKWOOD_REGS_PHYS_BASE,

View File

@ -16,6 +16,11 @@
#include <asm/sizes.h>
/*
* Clocks are derived from MCLK, which is 25Mhz
*/
#define KS8695_CLOCK_RATE 25000000
/*
* Physical RAM address.
*/

View File

@ -14,7 +14,8 @@
#ifndef __ASM_ARCH_TIMEX_H
#define __ASM_ARCH_TIMEX_H
/* timers are derived from MCLK, which is 25MHz */
#define CLOCK_TICK_RATE 25000000
#include <mach/hardware.h>
#define CLOCK_TICK_RATE KS8695_CLOCK_RATE
#endif

View File

@ -245,6 +245,9 @@ static int ks8695_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs
static void __init ks8695_pci_preinit(void)
{
/* make software reset to avoid freeze if PCI bus was messed up */
__raw_writel(0x80000000, KS8695_PCI_VA + KS8695_PBCS);
/* stage 1 initialization, subid, subdevice = 0x0001 */
__raw_writel(0x00010001, KS8695_PCI_VA + KS8695_CRCSID);

View File

@ -63,7 +63,7 @@ static struct imxuart_platform_data uart_pdata = {
static int devboard_sdhc2_get_ro(struct device *dev)
{
return gpio_get_value(SDHC2_WP);
return !gpio_get_value(SDHC2_WP);
}
static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq,

View File

@ -67,7 +67,7 @@ static unsigned int marxbot_pins[] = {
static int marxbot_sdhc2_get_ro(struct device *dev)
{
return gpio_get_value(SDHC2_WP);
return !gpio_get_value(SDHC2_WP);
}
static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq,

View File

@ -94,7 +94,7 @@ static struct imxi2c_platform_data moboard_i2c1_pdata = {
static int moboard_sdhc1_get_ro(struct device *dev)
{
return gpio_get_value(SDHC1_WP);
return !gpio_get_value(SDHC1_WP);
}
static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq,

View File

@ -24,15 +24,6 @@
#include "devices.h"
static unsigned int pcm037_eet_pins[] = {
/* SPI #1 */
MX31_PIN_CSPI1_MISO__MISO,
MX31_PIN_CSPI1_MOSI__MOSI,
MX31_PIN_CSPI1_SCLK__SCLK,
MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
MX31_PIN_CSPI1_SS0__SS0,
MX31_PIN_CSPI1_SS1__SS1,
MX31_PIN_CSPI1_SS2__SS2,
/* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */
IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO),
/* GPIO keys */

View File

@ -19,7 +19,6 @@
#include <mach/irqs.h>
#include <mach/dma.h>
#include <mach/irqs.h>
#include <mach/mux.h>
#include <mach/cpu.h>
#include <mach/mcbsp.h>

View File

@ -141,7 +141,7 @@ static inline void board_smc91x_init(void)
static void __init omap_2430sdp_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
}

View File

@ -169,7 +169,7 @@ static struct platform_device *sdp3430_devices[] __initdata = {
static void __init omap_3430sdp_init_irq(void)
{
omap2_init_common_hw(hyb18m512160af6_sdrc_params);
omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL);
omap_init_irq();
omap_gpio_init();
}

View File

@ -59,7 +59,7 @@ static void __init gic_init_irq(void)
static void __init omap_4430sdp_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
#ifdef CONFIG_OMAP_32K_TIMER
omap2_gp_clockevent_set_gptimer(1);
#endif

View File

@ -250,7 +250,7 @@ out:
static void __init omap_apollon_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
apollon_init_smc91x();

View File

@ -33,7 +33,7 @@
static void __init omap_generic_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
}

View File

@ -270,7 +270,7 @@ static void __init h4_init_flash(void)
static void __init omap_h4_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
h4_init_flash();

View File

@ -270,7 +270,7 @@ static inline void __init ldp_init_smsc911x(void)
static void __init omap_ldp_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
ldp_init_smsc911x();

View File

@ -282,7 +282,8 @@ static int __init omap3_beagle_i2c_init(void)
static void __init omap3_beagle_init_irq(void)
{
omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
omap_init_irq();
#ifdef CONFIG_OMAP_32K_TIMER
omap2_gp_clockevent_set_gptimer(12);
@ -408,6 +409,10 @@ static void __init omap3_beagle_init(void)
usb_musb_init();
omap3beagle_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_cfg_reg(H16_34XX_SDRC_CKE0);
omap_cfg_reg(H17_34XX_SDRC_CKE1);
}
static void __init omap3_beagle_map_io(void)

View File

@ -25,6 +25,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/i2c/twl4030.h>
#include <linux/usb/otg.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@ -279,7 +280,7 @@ struct spi_board_info omap3evm_spi_board_info[] = {
static void __init omap3_evm_init_irq(void)
{
omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
omap_init_irq();
omap_gpio_init();
omap3evm_init_smc911x();
@ -307,6 +308,10 @@ static void __init omap3_evm_init(void)
ARRAY_SIZE(omap3evm_spi_board_info));
omap_serial_init();
#ifdef CONFIG_NOP_USB_XCEIV
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
#endif
usb_musb_init();
ads7846_dev_init();
}

View File

@ -40,6 +40,7 @@
#include <mach/mcspi.h>
#include <mach/usb.h>
#include <mach/keypad.h>
#include <mach/mux.h>
#include "sdram-micron-mt46h32m32lf-6.h"
#include "mmc-twl4030.h"
@ -310,7 +311,8 @@ static int __init omap3pandora_i2c_init(void)
static void __init omap3pandora_init_irq(void)
{
omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
@ -397,6 +399,10 @@ static void __init omap3pandora_init(void)
omap3pandora_ads7846_init();
pandora_keys_gpio_init();
usb_musb_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_cfg_reg(H16_34XX_SDRC_CKE0);
omap_cfg_reg(H17_34XX_SDRC_CKE1);
}
static void __init omap3pandora_map_io(void)

View File

@ -44,6 +44,7 @@
#include <mach/gpmc.h>
#include <mach/hardware.h>
#include <mach/nand.h>
#include <mach/mux.h>
#include <mach/usb.h>
#include "sdram-micron-mt46h32m32lf-6.h"
@ -51,6 +52,7 @@
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
#define OVERO_GPIO_PENDOWN 114
#define OVERO_GPIO_BT_NRESET 164
#define OVERO_GPIO_USBH_CPEN 168
#define OVERO_GPIO_USBH_NRESET 183
@ -146,7 +148,7 @@ static struct platform_device overo_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(overo_smsc911x_resources),
.resource = &overo_smsc911x_resources,
.resource = overo_smsc911x_resources,
.dev = {
.platform_data = &overo_smsc911x_config,
},
@ -360,7 +362,8 @@ static int __init overo_i2c_init(void)
static void __init overo_init_irq(void)
{
omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
@ -395,6 +398,10 @@ static void __init overo_init(void)
overo_ads7846_init();
overo_init_smsc911x();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_cfg_reg(H16_34XX_SDRC_CKE0);
omap_cfg_reg(H17_34XX_SDRC_CKE1);
if ((gpio_request(OVERO_GPIO_W2W_NRESET,
"OVERO_GPIO_W2W_NRESET") == 0) &&
(gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) {

View File

@ -278,6 +278,10 @@ static struct twl4030_gpio_platform_data rx51_gpio_data = {
.setup = rx51_twlgpio_setup,
};
static struct twl4030_usb_data rx51_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
static struct twl4030_platform_data rx51_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
@ -286,6 +290,7 @@ static struct twl4030_platform_data rx51_twldata = {
.gpio = &rx51_gpio_data,
.keypad = &rx51_kp_data,
.madc = &rx51_madc_data,
.usb = &rx51_usb_data,
.vaux1 = &rx51_vaux1,
.vaux2 = &rx51_vaux2,

View File

@ -61,7 +61,7 @@ static struct omap_board_config_kernel rx51_config[] = {
static void __init rx51_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
}
@ -75,6 +75,10 @@ static void __init rx51_init(void)
omap_serial_init();
usb_musb_init();
rx51_peripherals_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_cfg_reg(H16_34XX_SDRC_CKE0);
omap_cfg_reg(H17_34XX_SDRC_CKE1);
}
static void __init rx51_map_io(void)

View File

@ -25,7 +25,7 @@
static void __init omap_zoom2_init_irq(void)
{
omap2_init_common_hw(NULL);
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
}

View File

@ -27,6 +27,7 @@
#include <mach/clock.h>
#include <mach/clockdomain.h>
#include <mach/cpu.h>
#include <mach/prcm.h>
#include <asm/div64.h>
#include <mach/sdrc.h>
@ -38,8 +39,6 @@
#include "cm-regbits-24xx.h"
#include "cm-regbits-34xx.h"
#define MAX_CLOCK_ENABLE_WAIT 100000
/* DPLL rate rounding: minimum DPLL multiplier, divider values */
#define DPLL_MIN_MULTIPLIER 1
#define DPLL_MIN_DIVIDER 1
@ -274,83 +273,97 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk)
}
/**
* omap2_wait_clock_ready - wait for clock to enable
* @reg: physical address of clock IDLEST register
* @mask: value to mask against to determine if the clock is active
* @name: name of the clock (for printk)
* omap2_clk_dflt_find_companion - find companion clock to @clk
* @clk: struct clk * to find the companion clock of
* @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in
* @other_bit: u8 ** to return the companion clock bit shift in
*
* Returns 1 if the clock enabled in time, or 0 if it failed to enable
* in roughly MAX_CLOCK_ENABLE_WAIT microseconds.
*/
int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name)
{
int i = 0;
int ena = 0;
/*
* 24xx uses 0 to indicate not ready, and 1 to indicate ready.
* 34xx reverses this, just to keep us on our toes
*/
if (cpu_mask & (RATE_IN_242X | RATE_IN_243X))
ena = mask;
else if (cpu_mask & RATE_IN_343X)
ena = 0;
/* Wait for lock */
while (((__raw_readl(reg) & mask) != ena) &&
(i++ < MAX_CLOCK_ENABLE_WAIT)) {
udelay(1);
}
if (i <= MAX_CLOCK_ENABLE_WAIT)
pr_debug("Clock %s stable after %d loops\n", name, i);
else
printk(KERN_ERR "Clock %s didn't enable in %d tries\n",
name, MAX_CLOCK_ENABLE_WAIT);
return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0;
};
/*
* Note: We don't need special code here for INVERT_ENABLE
* for the time being since INVERT_ENABLE only applies to clocks enabled by
* Note: We don't need special code here for INVERT_ENABLE for the
* time being since INVERT_ENABLE only applies to clocks enabled by
* CM_CLKEN_PLL
*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's
* just a matter of XORing the bits.
*
* Some clocks don't have companion clocks. For example, modules with
* only an interface clock (such as MAILBOXES) don't have a companion
* clock. Right now, this code relies on the hardware exporting a bit
* in the correct companion register that indicates that the
* nonexistent 'companion clock' is active. Future patches will
* associate this type of code with per-module data structures to
* avoid this issue, and remove the casts. No return value.
*/
static void omap2_clk_wait_ready(struct clk *clk)
void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
u8 *other_bit)
{
void __iomem *reg, *other_reg, *st_reg;
u32 bit;
/*
* REVISIT: This code is pretty ugly. It would be nice to generalize
* it and pull it into struct clk itself somehow.
*/
reg = clk->enable_reg;
u32 r;
/*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes
* it's just a matter of XORing the bits.
*/
other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN));
r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN));
/* Check if both functional and interface clocks
* are running. */
bit = 1 << clk->enable_bit;
if (!(__raw_readl(other_reg) & bit))
return;
st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */
omap2_wait_clock_ready(st_reg, bit, clk->name);
*other_reg = (__force void __iomem *)r;
*other_bit = clk->enable_bit;
}
static int omap2_dflt_clk_enable(struct clk *clk)
/**
* omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
* @clk: struct clk * to find IDLEST info for
* @idlest_reg: void __iomem ** to return the CM_IDLEST va in
* @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
*
* Return the CM_IDLEST register address and bit shift corresponding
* to the module that "owns" this clock. This default code assumes
* that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that
* the IDLEST register address ID corresponds to the CM_*CLKEN
* register address ID (e.g., that CM_FCLKEN2 corresponds to
* CM_IDLEST2). This is not true for all modules. No return value.
*/
void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
u8 *idlest_bit)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = clk->enable_bit;
}
/**
* omap2_module_wait_ready - wait for an OMAP module to leave IDLE
* @clk: struct clk * belonging to the module
*
* If the necessary clocks for the OMAP hardware IP block that
* corresponds to clock @clk are enabled, then wait for the module to
* indicate readiness (i.e., to leave IDLE). This code does not
* belong in the clock code and will be moved in the medium term to
* module-dependent code. No return value.
*/
static void omap2_module_wait_ready(struct clk *clk)
{
void __iomem *companion_reg, *idlest_reg;
u8 other_bit, idlest_bit;
/* Not all modules have multiple clocks that their IDLEST depends on */
if (clk->ops->find_companion) {
clk->ops->find_companion(clk, &companion_reg, &other_bit);
if (!(__raw_readl(companion_reg) & (1 << other_bit)))
return;
}
clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
}
int omap2_dflt_clk_enable(struct clk *clk)
{
u32 v;
if (unlikely(clk->enable_reg == NULL)) {
printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
pr_err("clock.c: Enable for %s without enable code\n",
clk->name);
return 0; /* REVISIT: -EINVAL */
}
@ -363,26 +376,13 @@ static int omap2_dflt_clk_enable(struct clk *clk)
__raw_writel(v, clk->enable_reg);
v = __raw_readl(clk->enable_reg); /* OCP barrier */
if (clk->ops->find_idlest)
omap2_module_wait_ready(clk);
return 0;
}
static int omap2_dflt_clk_enable_wait(struct clk *clk)
{
int ret;
if (!clk->enable_reg) {
printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
clk->name);
return 0; /* REVISIT: -EINVAL */
}
ret = omap2_dflt_clk_enable(clk);
if (ret == 0)
omap2_clk_wait_ready(clk);
return ret;
}
static void omap2_dflt_clk_disable(struct clk *clk)
void omap2_dflt_clk_disable(struct clk *clk)
{
u32 v;
@ -406,8 +406,10 @@ static void omap2_dflt_clk_disable(struct clk *clk)
}
const struct clkops clkops_omap2_dflt_wait = {
.enable = omap2_dflt_clk_enable_wait,
.enable = omap2_dflt_clk_enable,
.disable = omap2_dflt_clk_disable,
.find_companion = omap2_clk_dflt_find_companion,
.find_idlest = omap2_clk_dflt_find_idlest,
};
const struct clkops clkops_omap2_dflt = {

View File

@ -65,6 +65,12 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate);
u32 omap2_get_dpll_rate(struct clk *clk);
int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name);
void omap2_clk_prepare_for_reboot(void);
int omap2_dflt_clk_enable(struct clk *clk);
void omap2_dflt_clk_disable(struct clk *clk);
void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
u8 *other_bit);
void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
u8 *idlest_bit);
extern const struct clkops clkops_omap2_dflt_wait;
extern const struct clkops clkops_omap2_dflt;

View File

@ -30,6 +30,7 @@
#include <mach/clock.h>
#include <mach/sram.h>
#include <mach/prcm.h>
#include <asm/div64.h>
#include <asm/clkdev.h>
@ -43,6 +44,18 @@
static const struct clkops clkops_oscck;
static const struct clkops clkops_fixed;
static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit);
/* 2430 I2CHS has non-standard IDLEST register */
static const struct clkops clkops_omap2430_i2chs_wait = {
.enable = omap2_dflt_clk_enable,
.disable = omap2_dflt_clk_disable,
.find_idlest = omap2430_clk_i2chs_find_idlest,
.find_companion = omap2_clk_dflt_find_companion,
};
#include "clock24xx.h"
struct omap_clk {
@ -239,6 +252,26 @@ static void __iomem *prcm_clksrc_ctrl;
* Omap24xx specific clock functions
*-------------------------------------------------------------------------*/
/**
* omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
*
* OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
* CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function
* passes back the correct CM_IDLEST register address for I2CHS
* modules. No return value.
*/
static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit)
{
*idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
*idlest_bit = clk->enable_bit;
}
/**
* omap2xxx_clk_get_core_rate - return the CORE_CLK rate
* @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck")
@ -325,8 +358,8 @@ static int omap2_clk_fixed_enable(struct clk *clk)
else if (clk == &apll54_ck)
cval = OMAP24XX_ST_54M_APLL;
omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
clk->name);
omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
clk->name);
/*
* REVISIT: Should we return an error code if omap2_wait_clock_ready()

View File

@ -2337,7 +2337,7 @@ static struct clk i2c2_fck = {
static struct clk i2chs2_fck = {
.name = "i2c_fck",
.ops = &clkops_omap2_dflt_wait,
.ops = &clkops_omap2430_i2chs_wait,
.id = 2,
.parent = &func_96m_ck,
.clkdm_name = "core_l4_clkdm",
@ -2370,7 +2370,7 @@ static struct clk i2c1_fck = {
static struct clk i2chs1_fck = {
.name = "i2c_fck",
.ops = &clkops_omap2_dflt_wait,
.ops = &clkops_omap2430_i2chs_wait,
.id = 1,
.parent = &func_96m_ck,
.clkdm_name = "core_l4_clkdm",

View File

@ -2,7 +2,7 @@
* OMAP3-specific clock framework functions
*
* Copyright (C) 2007-2008 Texas Instruments, Inc.
* Copyright (C) 2007-2008 Nokia Corporation
* Copyright (C) 2007-2009 Nokia Corporation
*
* Written by Paul Walmsley
* Testing and integration fixes by Jouni Högander
@ -41,6 +41,37 @@
static const struct clkops clkops_noncore_dpll_ops;
static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit);
static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit);
static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit);
static const struct clkops clkops_omap3430es2_ssi_wait = {
.enable = omap2_dflt_clk_enable,
.disable = omap2_dflt_clk_disable,
.find_idlest = omap3430es2_clk_ssi_find_idlest,
.find_companion = omap2_clk_dflt_find_companion,
};
static const struct clkops clkops_omap3430es2_hsotgusb_wait = {
.enable = omap2_dflt_clk_enable,
.disable = omap2_dflt_clk_disable,
.find_idlest = omap3430es2_clk_hsotgusb_find_idlest,
.find_companion = omap2_clk_dflt_find_companion,
};
static const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
.enable = omap2_dflt_clk_enable,
.disable = omap2_dflt_clk_disable,
.find_idlest = omap3430es2_clk_dss_usbhost_find_idlest,
.find_companion = omap2_clk_dflt_find_companion,
};
#include "clock34xx.h"
struct omap_clk {
@ -157,10 +188,13 @@ static struct omap_clk omap34xx_clks[] = {
CLK(NULL, "fshostusb_fck", &fshostusb_fck, CK_3430ES1),
CLK(NULL, "core_12m_fck", &core_12m_fck, CK_343X),
CLK("omap_hdq.0", "fck", &hdq_fck, CK_343X),
CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck, CK_343X),
CLK(NULL, "ssi_sst_fck", &ssi_sst_fck, CK_343X),
CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es1, CK_3430ES1),
CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es2, CK_3430ES2),
CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es1, CK_3430ES1),
CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es2, CK_3430ES2),
CLK(NULL, "core_l3_ick", &core_l3_ick, CK_343X),
CLK("musb_hdrc", "ick", &hsotgusb_ick, CK_343X),
CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es1, CK_3430ES1),
CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es2, CK_3430ES2),
CLK(NULL, "sdrc_ick", &sdrc_ick, CK_343X),
CLK(NULL, "gpmc_fck", &gpmc_fck, CK_343X),
CLK(NULL, "security_l3_ick", &security_l3_ick, CK_343X),
@ -193,18 +227,21 @@ static struct omap_clk omap34xx_clks[] = {
CLK(NULL, "mailboxes_ick", &mailboxes_ick, CK_343X),
CLK(NULL, "omapctrl_ick", &omapctrl_ick, CK_343X),
CLK(NULL, "ssi_l4_ick", &ssi_l4_ick, CK_343X),
CLK(NULL, "ssi_ick", &ssi_ick, CK_343X),
CLK(NULL, "ssi_ick", &ssi_ick_3430es1, CK_3430ES1),
CLK(NULL, "ssi_ick", &ssi_ick_3430es2, CK_3430ES2),
CLK(NULL, "usb_l4_ick", &usb_l4_ick, CK_3430ES1),
CLK(NULL, "security_l4_ick2", &security_l4_ick2, CK_343X),
CLK(NULL, "aes1_ick", &aes1_ick, CK_343X),
CLK("omap_rng", "ick", &rng_ick, CK_343X),
CLK(NULL, "sha11_ick", &sha11_ick, CK_343X),
CLK(NULL, "des1_ick", &des1_ick, CK_343X),
CLK("omapfb", "dss1_fck", &dss1_alwon_fck, CK_343X),
CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es1, CK_3430ES1),
CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es2, CK_3430ES2),
CLK("omapfb", "tv_fck", &dss_tv_fck, CK_343X),
CLK("omapfb", "video_fck", &dss_96m_fck, CK_343X),
CLK("omapfb", "dss2_fck", &dss2_alwon_fck, CK_343X),
CLK("omapfb", "ick", &dss_ick, CK_343X),
CLK("omapfb", "ick", &dss_ick_3430es1, CK_3430ES1),
CLK("omapfb", "ick", &dss_ick_3430es2, CK_3430ES2),
CLK(NULL, "cam_mclk", &cam_mclk, CK_343X),
CLK(NULL, "cam_ick", &cam_ick, CK_343X),
CLK(NULL, "csi2_96m_fck", &csi2_96m_fck, CK_343X),
@ -300,6 +337,73 @@ static struct omap_clk omap34xx_clks[] = {
*/
#define SDRC_MPURATE_LOOPS 96
/**
* omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
*
* The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
* from the CM_{I,F}CLKEN bit. Pass back the correct info via
* @idlest_reg and @idlest_bit. No return value.
*/
static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
}
/**
* omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
*
* Some OMAP modules on OMAP3 ES2+ chips have both initiator and
* target IDLEST bits. For our purposes, we are concerned with the
* target IDLEST bits, which exist at a different bit position than
* the *CLKEN bit position for these modules (DSS and USBHOST) (The
* default find_idlest code assumes that they are at the same
* position.) No return value.
*/
static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
/* USBHOST_IDLE has same shift */
*idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
}
/**
* omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB
* @clk: struct clk * being enabled
* @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
* @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
*
* The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
* shift from the CM_{I,F}CLKEN bit. Pass back the correct info via
* @idlest_reg and @idlest_bit. No return value.
*/
static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
void __iomem **idlest_reg,
u8 *idlest_bit)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
}
/**
* omap3_dpll_recalc - recalculate DPLL rate
* @clk: DPLL struct clk
@ -725,7 +829,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
u32 unlock_dll = 0;
u32 c;
unsigned long validrate, sdrcrate, mpurate;
struct omap_sdrc_params *sp;
struct omap_sdrc_params *sdrc_cs0;
struct omap_sdrc_params *sdrc_cs1;
int ret;
if (!clk || !rate)
return -EINVAL;
@ -743,8 +849,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
else
sdrcrate >>= ((clk->rate / rate) >> 1);
sp = omap2_sdrc_get_params(sdrcrate);
if (!sp)
ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1);
if (ret)
return -EINVAL;
if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) {
@ -765,12 +871,29 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
validrate);
pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
pr_debug("clock: SDRC CS0 timing params used:"
" RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
sdrc_cs0->actim_ctrlb, sdrc_cs0->mr);
if (sdrc_cs1)
pr_debug("clock: SDRC CS1 timing params used: "
" RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
sp->actim_ctrlb, new_div, unlock_dll, c,
sp->mr, rate > clk->rate);
if (sdrc_cs1)
omap3_configure_core_dpll(
new_div, unlock_dll, c, rate > clk->rate,
sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
else
omap3_configure_core_dpll(
new_div, unlock_dll, c, rate > clk->rate,
sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
0, 0, 0, 0);
return 0;
}

View File

@ -1568,7 +1568,7 @@ static const struct clksel ssi_ssr_clksel[] = {
{ .parent = NULL }
};
static struct clk ssi_ssr_fck = {
static struct clk ssi_ssr_fck_3430es1 = {
.name = "ssi_ssr_fck",
.ops = &clkops_omap2_dflt,
.init = &omap2_init_clksel_parent,
@ -1581,10 +1581,31 @@ static struct clk ssi_ssr_fck = {
.recalc = &omap2_clksel_recalc,
};
static struct clk ssi_sst_fck = {
static struct clk ssi_ssr_fck_3430es2 = {
.name = "ssi_ssr_fck",
.ops = &clkops_omap3430es2_ssi_wait,
.init = &omap2_init_clksel_parent,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
.enable_bit = OMAP3430_EN_SSI_SHIFT,
.clksel_reg = OMAP_CM_REGADDR(CORE_MOD, CM_CLKSEL),
.clksel_mask = OMAP3430_CLKSEL_SSI_MASK,
.clksel = ssi_ssr_clksel,
.clkdm_name = "core_l4_clkdm",
.recalc = &omap2_clksel_recalc,
};
static struct clk ssi_sst_fck_3430es1 = {
.name = "ssi_sst_fck",
.ops = &clkops_null,
.parent = &ssi_ssr_fck,
.parent = &ssi_ssr_fck_3430es1,
.fixed_div = 2,
.recalc = &omap2_fixed_divisor_recalc,
};
static struct clk ssi_sst_fck_3430es2 = {
.name = "ssi_sst_fck",
.ops = &clkops_null,
.parent = &ssi_ssr_fck_3430es2,
.fixed_div = 2,
.recalc = &omap2_fixed_divisor_recalc,
};
@ -1606,9 +1627,19 @@ static struct clk core_l3_ick = {
.recalc = &followparent_recalc,
};
static struct clk hsotgusb_ick = {
static struct clk hsotgusb_ick_3430es1 = {
.name = "hsotgusb_ick",
.ops = &clkops_omap2_dflt_wait,
.ops = &clkops_omap2_dflt,
.parent = &core_l3_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT,
.clkdm_name = "core_l3_clkdm",
.recalc = &followparent_recalc,
};
static struct clk hsotgusb_ick_3430es2 = {
.name = "hsotgusb_ick",
.ops = &clkops_omap3430es2_hsotgusb_wait,
.parent = &core_l3_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT,
@ -1947,7 +1978,7 @@ static struct clk ssi_l4_ick = {
.recalc = &followparent_recalc,
};
static struct clk ssi_ick = {
static struct clk ssi_ick_3430es1 = {
.name = "ssi_ick",
.ops = &clkops_omap2_dflt,
.parent = &ssi_l4_ick,
@ -1957,6 +1988,16 @@ static struct clk ssi_ick = {
.recalc = &followparent_recalc,
};
static struct clk ssi_ick_3430es2 = {
.name = "ssi_ick",
.ops = &clkops_omap3430es2_ssi_wait,
.parent = &ssi_l4_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430_EN_SSI_SHIFT,
.clkdm_name = "core_l4_clkdm",
.recalc = &followparent_recalc,
};
/* REVISIT: Technically the TRM claims that this is CORE_CLK based,
* but l4_ick makes more sense to me */
@ -2024,7 +2065,7 @@ static struct clk des1_ick = {
};
/* DSS */
static struct clk dss1_alwon_fck = {
static struct clk dss1_alwon_fck_3430es1 = {
.name = "dss1_alwon_fck",
.ops = &clkops_omap2_dflt,
.parent = &dpll4_m4x2_ck,
@ -2034,6 +2075,16 @@ static struct clk dss1_alwon_fck = {
.recalc = &followparent_recalc,
};
static struct clk dss1_alwon_fck_3430es2 = {
.name = "dss1_alwon_fck",
.ops = &clkops_omap3430es2_dss_usbhost_wait,
.parent = &dpll4_m4x2_ck,
.enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN),
.enable_bit = OMAP3430_EN_DSS1_SHIFT,
.clkdm_name = "dss_clkdm",
.recalc = &followparent_recalc,
};
static struct clk dss_tv_fck = {
.name = "dss_tv_fck",
.ops = &clkops_omap2_dflt,
@ -2067,7 +2118,7 @@ static struct clk dss2_alwon_fck = {
.recalc = &followparent_recalc,
};
static struct clk dss_ick = {
static struct clk dss_ick_3430es1 = {
/* Handles both L3 and L4 clocks */
.name = "dss_ick",
.ops = &clkops_omap2_dflt,
@ -2079,6 +2130,18 @@ static struct clk dss_ick = {
.recalc = &followparent_recalc,
};
static struct clk dss_ick_3430es2 = {
/* Handles both L3 and L4 clocks */
.name = "dss_ick",
.ops = &clkops_omap3430es2_dss_usbhost_wait,
.parent = &l4_ick,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN),
.enable_bit = OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT,
.clkdm_name = "dss_clkdm",
.recalc = &followparent_recalc,
};
/* CAM */
static struct clk cam_mclk = {
@ -2118,7 +2181,7 @@ static struct clk csi2_96m_fck = {
static struct clk usbhost_120m_fck = {
.name = "usbhost_120m_fck",
.ops = &clkops_omap2_dflt_wait,
.ops = &clkops_omap2_dflt,
.parent = &dpll5_m2_ck,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
@ -2129,7 +2192,7 @@ static struct clk usbhost_120m_fck = {
static struct clk usbhost_48m_fck = {
.name = "usbhost_48m_fck",
.ops = &clkops_omap2_dflt_wait,
.ops = &clkops_omap3430es2_dss_usbhost_wait,
.parent = &omap_48m_fck,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
@ -2141,7 +2204,7 @@ static struct clk usbhost_48m_fck = {
static struct clk usbhost_ick = {
/* Handles both L3 and L4 clocks */
.name = "usbhost_ick",
.ops = &clkops_omap2_dflt_wait,
.ops = &clkops_omap3430es2_dss_usbhost_wait,
.parent = &l4_ick,
.init = &omap2_init_clk_clkdm,
.enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN),

View File

@ -29,9 +29,9 @@
* These registers appear once per CM module.
*/
#define OMAP3430_CM_REVISION OMAP_CM_REGADDR(OCP_MOD, 0x0000)
#define OMAP3430_CM_SYSCONFIG OMAP_CM_REGADDR(OCP_MOD, 0x0010)
#define OMAP3430_CM_POLCTRL OMAP_CM_REGADDR(OCP_MOD, 0x009c)
#define OMAP3430_CM_REVISION OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000)
#define OMAP3430_CM_SYSCONFIG OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010)
#define OMAP3430_CM_POLCTRL OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c)
#define OMAP3_CM_CLKOUT_CTRL_OFFSET 0x0070
#define OMAP3430_CM_CLKOUT_CTRL OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070)

View File

@ -276,14 +276,15 @@ static int __init _omap2_init_reprogram_sdrc(void)
return v;
}
void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1)
{
omap2_mux_init();
#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
pwrdm_init(powerdomains_omap);
clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
omap2_clk_init();
omap2_sdrc_init(sp);
omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
_omap2_init_reprogram_sdrc();
#endif
gpmc_init();

View File

@ -19,7 +19,6 @@
#include <mach/irqs.h>
#include <mach/dma.h>
#include <mach/irqs.h>
#include <mach/mux.h>
#include <mach/cpu.h>
#include <mach/mcbsp.h>

View File

@ -119,6 +119,7 @@ static int twl_mmc_late_init(struct device *dev)
if (i != 0)
break;
ret = PTR_ERR(reg);
hsmmc[i].vcc = NULL;
goto err;
}
hsmmc[i].vcc = reg;
@ -165,8 +166,13 @@ done:
static void twl_mmc_cleanup(struct device *dev)
{
struct omap_mmc_platform_data *mmc = dev->platform_data;
int i;
gpio_free(mmc->slots[0].switch_pin);
for(i = 0; i < ARRAY_SIZE(hsmmc); i++) {
regulator_put(hsmmc[i].vcc);
regulator_put(hsmmc[i].vcc_aux);
}
}
#ifdef CONFIG_PM

View File

@ -486,6 +486,12 @@ MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262,
OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264,
OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
};
#define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins)

View File

@ -11,9 +11,6 @@
#ifndef __ARCH_ARM_MACH_OMAP2_PM_H
#define __ARCH_ARM_MACH_OMAP2_PM_H
extern int omap2_pm_init(void);
extern int omap3_pm_init(void);
#ifdef CONFIG_PM_DEBUG
extern void omap2_pm_dump(int mode, int resume, unsigned int us);
extern int omap2_pm_debug;

View File

@ -470,7 +470,7 @@ static void __init prcm_setup_regs(void)
WKUP_MOD, PM_WKEN);
}
int __init omap2_pm_init(void)
static int __init omap2_pm_init(void)
{
u32 l;

View File

@ -39,7 +39,9 @@
struct power_state {
struct powerdomain *pwrdm;
u32 next_state;
#ifdef CONFIG_SUSPEND
u32 saved_state;
#endif
struct list_head node;
};
@ -293,6 +295,9 @@ out:
local_irq_enable();
}
#ifdef CONFIG_SUSPEND
static suspend_state_t suspend_state;
static int omap3_pm_prepare(void)
{
disable_hlt();
@ -321,7 +326,6 @@ static int omap3_pm_suspend(void)
restore:
/* Restore next_pwrsts */
list_for_each_entry(pwrst, &pwrst_list, node) {
set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
if (state > pwrst->next_state) {
printk(KERN_INFO "Powerdomain (%s) didn't enter "
@ -329,6 +333,7 @@ restore:
pwrst->pwrdm->name, pwrst->next_state);
ret = -1;
}
set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
}
if (ret)
printk(KERN_ERR "Could not enter target state in pm_suspend\n");
@ -339,11 +344,11 @@ restore:
return ret;
}
static int omap3_pm_enter(suspend_state_t state)
static int omap3_pm_enter(suspend_state_t unused)
{
int ret = 0;
switch (state) {
switch (suspend_state) {
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
ret = omap3_pm_suspend();
@ -360,12 +365,30 @@ static void omap3_pm_finish(void)
enable_hlt();
}
/* Hooks to enable / disable UART interrupts during suspend */
static int omap3_pm_begin(suspend_state_t state)
{
suspend_state = state;
omap_uart_enable_irqs(0);
return 0;
}
static void omap3_pm_end(void)
{
suspend_state = PM_SUSPEND_ON;
omap_uart_enable_irqs(1);
return;
}
static struct platform_suspend_ops omap_pm_ops = {
.begin = omap3_pm_begin,
.end = omap3_pm_end,
.prepare = omap3_pm_prepare,
.enter = omap3_pm_enter,
.finish = omap3_pm_finish,
.valid = suspend_valid_only_mem,
};
#endif /* CONFIG_SUSPEND */
/**
@ -613,6 +636,24 @@ static void __init prcm_setup_regs(void)
/* Clear any pending PRCM interrupts */
prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
/* Don't attach IVA interrupts */
prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
/* Clear any pending 'reset' flags */
prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST);
prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST);
prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST);
prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST);
prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST);
prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST);
prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST);
/* Clear any pending PRCM interrupts */
prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
omap3_iva_idle();
omap3_d2d_idle();
}
@ -652,7 +693,7 @@ static int __init clkdms_setup(struct clockdomain *clkdm)
return 0;
}
int __init omap3_pm_init(void)
static int __init omap3_pm_init(void)
{
struct power_state *pwrst, *tmp;
int ret;
@ -692,7 +733,9 @@ int __init omap3_pm_init(void)
_omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
omap34xx_cpu_suspend_sz);
#ifdef CONFIG_SUSPEND
suspend_set_ops(&omap_pm_ops);
#endif /* CONFIG_SUSPEND */
pm_idle = omap3_pm_idle;

View File

@ -17,6 +17,7 @@
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <mach/common.h>
#include <mach/prcm.h>
@ -28,6 +29,8 @@
static void __iomem *prm_base;
static void __iomem *cm_base;
#define MAX_MODULE_ENABLE_WAIT 100000
u32 omap_prcm_get_reset_sources(void)
{
/* XXX This presumably needs modification for 34XX */
@ -120,6 +123,46 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
}
EXPORT_SYMBOL(cm_rmw_mod_reg_bits);
/**
* omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
* @reg: physical address of module IDLEST register
* @mask: value to mask against to determine if the module is active
* @name: name of the clock (for printk)
*
* Returns 1 if the module indicated readiness in time, or 0 if it
* failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
*/
int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name)
{
int i = 0;
int ena = 0;
/*
* 24xx uses 0 to indicate not ready, and 1 to indicate ready.
* 34xx reverses this, just to keep us on our toes
*/
if (cpu_is_omap24xx())
ena = mask;
else if (cpu_is_omap34xx())
ena = 0;
else
BUG();
/* Wait for lock */
while (((__raw_readl(reg) & mask) != ena) &&
(i++ < MAX_MODULE_ENABLE_WAIT))
udelay(1);
if (i < MAX_MODULE_ENABLE_WAIT)
pr_debug("cm: Module associated with clock %s ready after %d "
"loops\n", name, i);
else
pr_err("cm: Module associated with clock %s didn't enable in "
"%d tries\n", name, MAX_MODULE_ENABLE_WAIT);
return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
};
void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals)
{
prm_base = omap2_globals->prm;

View File

@ -32,7 +32,7 @@
#include <mach/sdrc.h>
#include "sdrc.h"
static struct omap_sdrc_params *sdrc_init_params;
static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1;
void __iomem *omap2_sdrc_base;
void __iomem *omap2_sms_base;
@ -45,33 +45,49 @@ void __iomem *omap2_sms_base;
/**
* omap2_sdrc_get_params - return SDRC register values for a given clock rate
* @r: SDRC clock rate (in Hz)
* @sdrc_cs0: chip select 0 ram timings **
* @sdrc_cs1: chip select 1 ram timings **
*
* Return pre-calculated values for the SDRC_ACTIM_CTRLA,
* SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL, and SDRC_MR registers, for a given
* SDRC clock rate 'r'. These parameters control various timing
* delays in the SDRAM controller that are expressed in terms of the
* number of SDRC clock cycles to wait; hence the clock rate
* dependency. Note that sdrc_init_params must be sorted rate
* descending. Also assumes that both chip-selects use the same
* timing parameters. Returns a struct omap_sdrc_params * upon
* success, or NULL upon failure.
* SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL and SDRC_MR registers in sdrc_cs[01]
* structs,for a given SDRC clock rate 'r'.
* These parameters control various timing delays in the SDRAM controller
* that are expressed in terms of the number of SDRC clock cycles to
* wait; hence the clock rate dependency.
*
* Supports 2 different timing parameters for both chip selects.
*
* Note 1: the sdrc_init_params_cs[01] must be sorted rate descending.
* Note 2: If sdrc_init_params_cs_1 is not NULL it must be of same size
* as sdrc_init_params_cs_0.
*
* Fills in the struct omap_sdrc_params * for each chip select.
* Returns 0 upon success or -1 upon failure.
*/
struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r)
int omap2_sdrc_get_params(unsigned long r,
struct omap_sdrc_params **sdrc_cs0,
struct omap_sdrc_params **sdrc_cs1)
{
struct omap_sdrc_params *sp;
struct omap_sdrc_params *sp0, *sp1;
if (!sdrc_init_params)
return NULL;
if (!sdrc_init_params_cs0)
return -1;
sp = sdrc_init_params;
sp0 = sdrc_init_params_cs0;
sp1 = sdrc_init_params_cs1;
while (sp->rate && sp->rate != r)
sp++;
while (sp0->rate && sp0->rate != r) {
sp0++;
if (sdrc_init_params_cs1)
sp1++;
}
if (!sp->rate)
return NULL;
if (!sp0->rate)
return -1;
return sp;
*sdrc_cs0 = sp0;
*sdrc_cs1 = sp1;
return 0;
}
@ -83,13 +99,15 @@ void __init omap2_set_globals_sdrc(struct omap_globals *omap2_globals)
/**
* omap2_sdrc_init - initialize SMS, SDRC devices on boot
* @sp: pointer to a null-terminated list of struct omap_sdrc_params
* @sdrc_cs[01]: pointers to a null-terminated list of struct omap_sdrc_params
* Support for 2 chip selects timings
*
* Turn on smart idle modes for SDRAM scheduler and controller.
* Program a known-good configuration for the SDRC to deal with buggy
* bootloaders.
*/
void __init omap2_sdrc_init(struct omap_sdrc_params *sp)
void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1)
{
u32 l;
@ -103,11 +121,15 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sp)
l |= (0x2 << 3);
sdrc_write_reg(l, SDRC_SYSCONFIG);
sdrc_init_params = sp;
sdrc_init_params_cs0 = sdrc_cs0;
sdrc_init_params_cs1 = sdrc_cs1;
/* XXX Enable SRFRONIDLEREQ here also? */
/*
* PWDENA should not be set due to 34xx erratum 1.150 - PWDENA
* can cause random memory corruption
*/
l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) |
(1 << SDRC_POWER_PWDENA_SHIFT) |
(1 << SDRC_POWER_PAGEPOLICY_SHIFT);
sdrc_write_reg(l, SDRC_POWER);
}

View File

@ -54,6 +54,7 @@ struct omap_uart_state {
struct plat_serial8250_port *p;
struct list_head node;
struct platform_device pdev;
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
int context_valid;
@ -68,10 +69,9 @@ struct omap_uart_state {
#endif
};
static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS];
static LIST_HEAD(uart_list);
static struct plat_serial8250_port serial_platform_data[] = {
static struct plat_serial8250_port serial_platform_data0[] = {
{
.membase = IO_ADDRESS(OMAP_UART1_BASE),
.mapbase = OMAP_UART1_BASE,
@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
.flags = 0
}
};
static struct plat_serial8250_port serial_platform_data1[] = {
{
.membase = IO_ADDRESS(OMAP_UART2_BASE),
.mapbase = OMAP_UART2_BASE,
.irq = 73,
@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
.flags = 0
}
};
static struct plat_serial8250_port serial_platform_data2[] = {
{
.membase = IO_ADDRESS(OMAP_UART3_BASE),
.mapbase = OMAP_UART3_BASE,
.irq = 74,
@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
clk_disable(uart->fck);
}
static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
{
/* Set wake-enable bit */
if (uart->wk_en && uart->wk_mask) {
u32 v = __raw_readl(uart->wk_en);
v |= uart->wk_mask;
__raw_writel(v, uart->wk_en);
}
/* Ensure IOPAD wake-enables are set */
if (cpu_is_omap34xx() && uart->padconf) {
u16 v = omap_ctrl_readw(uart->padconf);
v |= OMAP3_PADCONF_WAKEUPENABLE0;
omap_ctrl_writew(v, uart->padconf);
}
}
static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
{
/* Clear wake-enable bit */
if (uart->wk_en && uart->wk_mask) {
u32 v = __raw_readl(uart->wk_en);
v &= ~uart->wk_mask;
__raw_writel(v, uart->wk_en);
}
/* Ensure IOPAD wake-enables are cleared */
if (cpu_is_omap34xx() && uart->padconf) {
u16 v = omap_ctrl_readw(uart->padconf);
v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
omap_ctrl_writew(v, uart->padconf);
}
}
static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
int enable)
{
@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
static void omap_uart_allow_sleep(struct omap_uart_state *uart)
{
if (device_may_wakeup(&uart->pdev.dev))
omap_uart_enable_wakeup(uart);
else
omap_uart_disable_wakeup(uart);
if (!uart->clocked)
return;
@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num)
/* Check for normal UART wakeup */
if (__raw_readl(uart->wk_st) & uart->wk_mask)
omap_uart_block_sleep(uart);
return;
}
}
@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
return IRQ_NONE;
}
static u32 sleep_timeout = DEFAULT_TIMEOUT;
static void omap_uart_idle_init(struct omap_uart_state *uart)
{
u32 v;
struct plat_serial8250_port *p = uart->p;
int ret;
uart->can_sleep = 0;
uart->timeout = sleep_timeout;
uart->timeout = DEFAULT_TIMEOUT;
setup_timer(&uart->timer, omap_uart_idle_timer,
(unsigned long) uart);
mod_timer(&uart->timer, jiffies + uart->timeout);
@ -413,76 +460,101 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
uart->padconf = 0;
}
/* Set wake-enable bit */
if (uart->wk_en && uart->wk_mask) {
v = __raw_readl(uart->wk_en);
v |= uart->wk_mask;
__raw_writel(v, uart->wk_en);
}
/* Ensure IOPAD wake-enables are set */
if (cpu_is_omap34xx() && uart->padconf) {
u16 v;
v = omap_ctrl_readw(uart->padconf);
v |= OMAP3_PADCONF_WAKEUPENABLE0;
omap_ctrl_writew(v, uart->padconf);
}
p->flags |= UPF_SHARE_IRQ;
ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED,
"serial idle", (void *)uart);
WARN_ON(ret);
}
static ssize_t sleep_timeout_show(struct kobject *kobj,
struct kobj_attribute *attr,
char *buf)
void omap_uart_enable_irqs(int enable)
{
return sprintf(buf, "%u\n", sleep_timeout / HZ);
int ret;
struct omap_uart_state *uart;
list_for_each_entry(uart, &uart_list, node) {
if (enable)
ret = request_irq(uart->p->irq, omap_uart_interrupt,
IRQF_SHARED, "serial idle", (void *)uart);
else
free_irq(uart->p->irq, (void *)uart);
}
}
static ssize_t sleep_timeout_store(struct kobject *kobj,
struct kobj_attribute *attr,
static ssize_t sleep_timeout_show(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct platform_device *pdev = container_of(dev,
struct platform_device, dev);
struct omap_uart_state *uart = container_of(pdev,
struct omap_uart_state, pdev);
return sprintf(buf, "%u\n", uart->timeout / HZ);
}
static ssize_t sleep_timeout_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t n)
{
struct omap_uart_state *uart;
struct platform_device *pdev = container_of(dev,
struct platform_device, dev);
struct omap_uart_state *uart = container_of(pdev,
struct omap_uart_state, pdev);
unsigned int value;
if (sscanf(buf, "%u", &value) != 1) {
printk(KERN_ERR "sleep_timeout_store: Invalid value\n");
return -EINVAL;
}
sleep_timeout = value * HZ;
list_for_each_entry(uart, &uart_list, node) {
uart->timeout = sleep_timeout;
if (uart->timeout)
mod_timer(&uart->timer, jiffies + uart->timeout);
else
/* A zero value means disable timeout feature */
omap_uart_block_sleep(uart);
}
uart->timeout = value * HZ;
if (uart->timeout)
mod_timer(&uart->timer, jiffies + uart->timeout);
else
/* A zero value means disable timeout feature */
omap_uart_block_sleep(uart);
return n;
}
static struct kobj_attribute sleep_timeout_attr =
__ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
#else
static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
#define DEV_CREATE_FILE(dev, attr)
#endif /* CONFIG_PM */
static struct platform_device serial_device = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev = {
.platform_data = serial_platform_data,
static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = {
{
.pdev = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev = {
.platform_data = serial_platform_data0,
},
},
}, {
.pdev = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM1,
.dev = {
.platform_data = serial_platform_data1,
},
},
}, {
.pdev = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM2,
.dev = {
.platform_data = serial_platform_data2,
},
},
},
};
void __init omap_serial_init(void)
{
int i, err;
int i;
const struct omap_uart_config *info;
char name[16];
@ -496,14 +568,12 @@ void __init omap_serial_init(void)
if (info == NULL)
return;
if (cpu_is_omap44xx()) {
for (i = 0; i < OMAP_MAX_NR_PORTS; i++)
serial_platform_data[i].irq += 32;
}
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
struct plat_serial8250_port *p = serial_platform_data + i;
struct omap_uart_state *uart = &omap_uart[i];
struct platform_device *pdev = &uart->pdev;
struct device *dev = &pdev->dev;
struct plat_serial8250_port *p = dev->platform_data;
if (!(info->enabled_uarts & (1 << i))) {
p->membase = NULL;
@ -531,20 +601,21 @@ void __init omap_serial_init(void)
uart->num = i;
p->private_data = uart;
uart->p = p;
list_add(&uart->node, &uart_list);
list_add_tail(&uart->node, &uart_list);
if (cpu_is_omap44xx())
p->irq += 32;
omap_uart_enable_clocks(uart);
omap_uart_reset(uart);
omap_uart_idle_init(uart);
if (WARN_ON(platform_device_register(pdev)))
continue;
if ((cpu_is_omap34xx() && uart->padconf) ||
(uart->wk_en && uart->wk_mask)) {
device_init_wakeup(dev, true);
DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout);
}
}
err = platform_device_register(&serial_device);
#ifdef CONFIG_PM
if (!err)
err = sysfs_create_file(&serial_device.dev.kobj,
&sleep_timeout_attr.attr);
#endif
}

View File

@ -36,7 +36,7 @@
.text
/* r4 parameters */
/* r1 parameters */
#define SDRC_NO_UNLOCK_DLL 0x0
#define SDRC_UNLOCK_DLL 0x1
@ -58,7 +58,6 @@
/* SDRC_POWER bit settings */
#define SRFRONIDLEREQ_MASK 0x40
#define PWDENA_MASK 0x4
/* CM_IDLEST1_CORE bit settings */
#define ST_SDRC_MASK 0x2
@ -71,41 +70,72 @@
/*
* omap3_sram_configure_core_dpll - change DPLL3 M2 divider
* r0 = new SDRC_RFR_CTRL register contents
* r1 = new SDRC_ACTIM_CTRLA register contents
* r2 = new SDRC_ACTIM_CTRLB register contents
* r3 = new M2 divider setting (only 1 and 2 supported right now)
* r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
* SDRC rates < 83MHz
* r5 = number of MPU cycles to wait for SDRC to stabilize after
* reprogramming the SDRC when switching to a slower MPU speed
* r6 = new SDRC_MR_0 register value
* r7 = increasing SDRC rate? (1 = yes, 0 = no)
*
* Params passed in registers:
* r0 = new M2 divider setting (only 1 and 2 supported right now)
* r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
* SDRC rates < 83MHz
* r2 = number of MPU cycles to wait for SDRC to stabilize after
* reprogramming the SDRC when switching to a slower MPU speed
* r3 = increasing SDRC rate? (1 = yes, 0 = no)
*
* Params passed via the stack. The needed params will be copied in SRAM
* before use by the code in SRAM (SDRAM is not accessible during SDRC
* reconfiguration):
* new SDRC_RFR_CTRL_0 register contents
* new SDRC_ACTIM_CTRL_A_0 register contents
* new SDRC_ACTIM_CTRL_B_0 register contents
* new SDRC_MR_0 register value
* new SDRC_RFR_CTRL_1 register contents
* new SDRC_ACTIM_CTRL_A_1 register contents
* new SDRC_ACTIM_CTRL_B_1 register contents
* new SDRC_MR_1 register value
*
* If the param SDRC_RFR_CTRL_1 is 0, the parameters
* are not programmed into the SDRC CS1 registers
*/
ENTRY(omap3_sram_configure_core_dpll)
stmfd sp!, {r1-r12, lr} @ store regs to stack
ldr r4, [sp, #52] @ pull extra args off the stack
ldr r5, [sp, #56] @ load extra args from the stack
ldr r6, [sp, #60] @ load extra args from the stack
ldr r7, [sp, #64] @ load extra args from the stack
@ pull the extra args off the stack
@ and store them in SRAM
ldr r4, [sp, #52]
str r4, omap_sdrc_rfr_ctrl_0_val
ldr r4, [sp, #56]
str r4, omap_sdrc_actim_ctrl_a_0_val
ldr r4, [sp, #60]
str r4, omap_sdrc_actim_ctrl_b_0_val
ldr r4, [sp, #64]
str r4, omap_sdrc_mr_0_val
ldr r4, [sp, #68]
str r4, omap_sdrc_rfr_ctrl_1_val
cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0,
beq skip_cs1_params @ do not use cs1 params
ldr r4, [sp, #72]
str r4, omap_sdrc_actim_ctrl_a_1_val
ldr r4, [sp, #76]
str r4, omap_sdrc_actim_ctrl_b_1_val
ldr r4, [sp, #80]
str r4, omap_sdrc_mr_1_val
skip_cs1_params:
dsb @ flush buffered writes to interconnect
cmp r7, #1 @ if increasing SDRC clk rate,
cmp r3, #1 @ if increasing SDRC clk rate,
bleq configure_sdrc @ program the SDRC regs early (for RFR)
cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state
cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state
bleq unlock_dll
blne lock_dll
bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC
bl configure_core_dpll @ change the DPLL3 M2 divider
mov r12, r2
bl wait_clk_stable @ wait for SDRC to stabilize
bl enable_sdrc @ take SDRC out of idle
cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change
cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change
bleq wait_dll_unlock
blne wait_dll_lock
cmp r7, #1 @ if increasing SDRC clk rate,
cmp r3, #1 @ if increasing SDRC clk rate,
beq return_to_sdram @ return to SDRAM code, otherwise,
bl configure_sdrc @ reprogram SDRC regs now
mov r12, r5
bl wait_clk_stable @ wait for SDRC to stabilize
return_to_sdram:
isb @ prevent speculative exec past here
mov r0, #0 @ return value
@ -113,7 +143,7 @@ return_to_sdram:
unlock_dll:
ldr r11, omap3_sdrc_dlla_ctrl
ldr r12, [r11]
and r12, r12, #FIXEDDELAY_MASK
bic r12, r12, #FIXEDDELAY_MASK
orr r12, r12, #FIXEDDELAY_DEFAULT
orr r12, r12, #DLLIDLE_MASK
str r12, [r11] @ (no OCP barrier needed)
@ -129,7 +159,6 @@ sdram_in_selfrefresh:
ldr r12, [r11] @ read the contents of SDRC_POWER
mov r9, r12 @ keep a copy of SDRC_POWER bits
orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle
bic r12, r12, #PWDENA_MASK @ clear PWDENA
str r12, [r11] @ write back to SDRC_POWER register
ldr r12, [r11] @ posted-write barrier for SDRC
idle_sdrc:
@ -149,7 +178,7 @@ configure_core_dpll:
ldr r12, [r11]
ldr r10, core_m2_mask_val @ modify m2 for core dpll
and r12, r12, r10
orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
str r12, [r11]
ldr r12, [r11] @ posted-write barrier for CM
bx lr
@ -187,15 +216,34 @@ wait_dll_unlock:
bne wait_dll_unlock
bx lr
configure_sdrc:
ldr r11, omap3_sdrc_rfr_ctrl
str r0, [r11]
ldr r11, omap3_sdrc_actim_ctrla
str r1, [r11]
ldr r11, omap3_sdrc_actim_ctrlb
str r2, [r11]
ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM
ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM
str r12, [r11] @ store
ldr r12, omap_sdrc_actim_ctrl_a_0_val
ldr r11, omap3_sdrc_actim_ctrl_a_0
str r12, [r11]
ldr r12, omap_sdrc_actim_ctrl_b_0_val
ldr r11, omap3_sdrc_actim_ctrl_b_0
str r12, [r11]
ldr r12, omap_sdrc_mr_0_val
ldr r11, omap3_sdrc_mr_0
str r6, [r11]
ldr r6, [r11] @ posted-write barrier for SDRC
str r12, [r11]
ldr r12, omap_sdrc_rfr_ctrl_1_val
cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0,
beq skip_cs1_prog @ do not program cs1 params
ldr r11, omap3_sdrc_rfr_ctrl_1
str r12, [r11]
ldr r12, omap_sdrc_actim_ctrl_a_1_val
ldr r11, omap3_sdrc_actim_ctrl_a_1
str r12, [r11]
ldr r12, omap_sdrc_actim_ctrl_b_1_val
ldr r11, omap3_sdrc_actim_ctrl_b_1
str r12, [r11]
ldr r12, omap_sdrc_mr_1_val
ldr r11, omap3_sdrc_mr_1
str r12, [r11]
skip_cs1_prog:
ldr r12, [r11] @ posted-write barrier for SDRC
bx lr
omap3_sdrc_power:
@ -206,14 +254,40 @@ omap3_cm_idlest1_core:
.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST)
omap3_cm_iclken1_core:
.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1)
omap3_sdrc_rfr_ctrl:
omap3_sdrc_rfr_ctrl_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0)
omap3_sdrc_actim_ctrla:
omap3_sdrc_rfr_ctrl_1:
.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1)
omap3_sdrc_actim_ctrl_a_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
omap3_sdrc_actim_ctrlb:
omap3_sdrc_actim_ctrl_a_1:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1)
omap3_sdrc_actim_ctrl_b_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
omap3_sdrc_actim_ctrl_b_1:
.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1)
omap3_sdrc_mr_0:
.word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
omap3_sdrc_mr_1:
.word OMAP34XX_SDRC_REGADDR(SDRC_MR_1)
omap_sdrc_rfr_ctrl_0_val:
.word 0xDEADBEEF
omap_sdrc_rfr_ctrl_1_val:
.word 0xDEADBEEF
omap_sdrc_actim_ctrl_a_0_val:
.word 0xDEADBEEF
omap_sdrc_actim_ctrl_a_1_val:
.word 0xDEADBEEF
omap_sdrc_actim_ctrl_b_0_val:
.word 0xDEADBEEF
omap_sdrc_actim_ctrl_b_1_val:
.word 0xDEADBEEF
omap_sdrc_mr_0_val:
.word 0xDEADBEEF
omap_sdrc_mr_1_val:
.word 0xDEADBEEF
omap3_sdrc_dlla_status:
.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
omap3_sdrc_dlla_ctrl:
@ -223,3 +297,4 @@ core_m2_mask_val:
ENTRY(omap3_sram_configure_core_dpll_sz)
.word . - omap3_sram_configure_core_dpll

View File

@ -155,20 +155,6 @@ static struct platform_device musb_device = {
.resource = musb_resources,
};
#ifdef CONFIG_NOP_USB_XCEIV
static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32);
static struct platform_device nop_xceiv_device = {
.name = "nop_usb_xceiv",
.id = -1,
.dev = {
.dma_mask = &nop_xceiv_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = NULL,
},
};
#endif
void __init usb_musb_init(void)
{
if (cpu_is_omap243x())
@ -183,13 +169,6 @@ void __init usb_musb_init(void)
*/
musb_plat.clock = "ick";
#ifdef CONFIG_NOP_USB_XCEIV
if (platform_device_register(&nop_xceiv_device) < 0) {
printk(KERN_ERR "Unable to register NOP-XCEIV device\n");
return;
}
#endif
if (platform_device_register(&musb_device) < 0) {
printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
return;

View File

@ -1141,12 +1141,16 @@ struct power_supply_info em_x270_psy_info = {
static void em_x270_battery_low(void)
{
#if defined(CONFIG_APM_EMULATION)
apm_queue_event(APM_LOW_BATTERY);
#endif
}
static void em_x270_battery_critical(void)
{
#if defined(CONFIG_APM_EMULATION)
apm_queue_event(APM_CRITICAL_SUSPEND);
#endif
}
struct da9030_battery_info em_x270_batterty_info = {

View File

@ -128,6 +128,10 @@ static unsigned long palmld_pin_config[] __initdata = {
GPIO38_GPIO, /* wifi ready */
GPIO81_GPIO, /* wifi reset */
/* FFUART */
GPIO34_FFUART_RXD,
GPIO39_FFUART_TXD,
/* HDD */
GPIO98_GPIO, /* HDD reset */
GPIO115_GPIO, /* HDD power */

View File

@ -111,6 +111,10 @@ static unsigned long palmt5_pin_config[] __initdata = {
/* PWM */
GPIO16_PWM0_OUT,
/* FFUART */
GPIO34_FFUART_RXD,
GPIO39_FFUART_TXD,
/* MISC */
GPIO10_GPIO, /* hotsync button */
GPIO90_GPIO, /* power detect */

View File

@ -127,6 +127,10 @@ static unsigned long palmtx_pin_config[] __initdata = {
GPIO76_LCD_PCLK,
GPIO77_LCD_BIAS,
/* FFUART */
GPIO34_FFUART_RXD,
GPIO39_FFUART_TXD,
/* MISC. */
GPIO10_GPIO, /* hotsync button */
GPIO12_GPIO, /* power detect */

View File

@ -409,7 +409,7 @@ err1:
static void treo680_irda_shutdown(struct device *dev)
{
gpio_free(GPIO_NR_TREO680_AMP_EN);
gpio_free(GPIO_NR_TREO680_IR_EN);
}
static struct pxaficp_platform_data treo680_ficp_info = {

View File

@ -197,10 +197,12 @@ static void __init zylonite_detect_lcd_panel(void)
for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
id = id << 1;
gpio = mfp_to_gpio(lcd_detect_pins[i]);
gpio_request(gpio, "LCD_ID_PINS");
gpio_direction_input(gpio);
if (gpio_get_value(gpio))
id = id | 0x1;
gpio_free(gpio);
}
/* lcd id, flush out bit 1 */

View File

@ -176,10 +176,12 @@ static void __init zylonite_detect_lcd_panel(void)
for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
id = id << 1;
gpio = mfp_to_gpio(lcd_detect_pins[i]);
gpio_request(gpio, "LCD_ID_PINS");
gpio_direction_input(gpio);
if (gpio_get_value(gpio))
id = id | 0x1;
gpio_free(gpio);
}
/* lcd id, flush out bit 1 */

View File

@ -28,7 +28,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin)
return NULL;
chip = &s3c24xx_gpios[pin/32];
return (S3C2410_GPIO_OFFSET(pin) > chip->chip.ngpio) ? chip : NULL;
return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL;
}
#endif /* __ASM_ARCH_GPIO_CORE_H */

View File

@ -510,7 +510,7 @@ static struct db_chip db_chips[] __initdata = {
}
};
static void u300_init_check_chip(void)
static void __init u300_init_check_chip(void)
{
u16 val;

View File

@ -120,6 +120,32 @@ void show_mem(void)
printk("%d pages swap cached\n", cached);
}
static void __init find_node_limits(int node, struct meminfo *mi,
unsigned long *min, unsigned long *max_low, unsigned long *max_high)
{
int i;
*min = -1UL;
*max_low = *max_high = 0;
for_each_nodebank(i, mi, node) {
struct membank *bank = &mi->bank[i];
unsigned long start, end;
start = bank_pfn_start(bank);
end = bank_pfn_end(bank);
if (*min > start)
*min = start;
if (*max_high < end)
*max_high = end;
if (bank->highmem)
continue;
if (*max_low < end)
*max_low = end;
}
}
/*
* FIXME: We really want to avoid allocating the bootmap bitmap
* over the top of the initrd. Hopefully, this is located towards
@ -210,40 +236,24 @@ static inline void map_memory_bank(struct membank *bank)
#endif
}
static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
static void __init bootmem_init_node(int node, struct meminfo *mi,
unsigned long start_pfn, unsigned long end_pfn)
{
unsigned long start_pfn, end_pfn, boot_pfn;
unsigned long boot_pfn;
unsigned int boot_pages;
pg_data_t *pgdat;
int i;
start_pfn = -1UL;
end_pfn = 0;
/*
* Calculate the pfn range, and map the memory banks for this node.
* Map the memory banks for this node.
*/
for_each_nodebank(i, mi, node) {
struct membank *bank = &mi->bank[i];
unsigned long start, end;
start = bank_pfn_start(bank);
end = bank_pfn_end(bank);
if (start_pfn > start)
start_pfn = start;
if (end_pfn < end)
end_pfn = end;
map_memory_bank(bank);
if (!bank->highmem)
map_memory_bank(bank);
}
/*
* If there is no memory in this node, ignore it.
*/
if (end_pfn == 0)
return end_pfn;
/*
* Allocate the bootmem bitmap page.
*/
@ -260,7 +270,8 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
for_each_nodebank(i, mi, node) {
struct membank *bank = &mi->bank[i];
free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank));
if (!bank->highmem)
free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank));
memory_present(node, bank_pfn_start(bank), bank_pfn_end(bank));
}
@ -269,8 +280,6 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
*/
reserve_bootmem_node(pgdat, boot_pfn << PAGE_SHIFT,
boot_pages << PAGE_SHIFT, BOOTMEM_DEFAULT);
return end_pfn;
}
static void __init bootmem_reserve_initrd(int node)
@ -297,33 +306,39 @@ static void __init bootmem_reserve_initrd(int node)
static void __init bootmem_free_node(int node, struct meminfo *mi)
{
unsigned long zone_size[MAX_NR_ZONES], zhole_size[MAX_NR_ZONES];
unsigned long start_pfn, end_pfn;
pg_data_t *pgdat = NODE_DATA(node);
unsigned long min, max_low, max_high;
int i;
start_pfn = pgdat->bdata->node_min_pfn;
end_pfn = pgdat->bdata->node_low_pfn;
find_node_limits(node, mi, &min, &max_low, &max_high);
/*
* initialise the zones within this node.
*/
memset(zone_size, 0, sizeof(zone_size));
memset(zhole_size, 0, sizeof(zhole_size));
/*
* The size of this node has already been determined. If we need
* to do anything fancy with the allocation of this memory to the
* zones, now is the time to do it.
*/
zone_size[0] = end_pfn - start_pfn;
zone_size[0] = max_low - min;
#ifdef CONFIG_HIGHMEM
zone_size[ZONE_HIGHMEM] = max_high - max_low;
#endif
/*
* For each bank in this node, calculate the size of the holes.
* holes = node_size - sum(bank_sizes_in_node)
*/
zhole_size[0] = zone_size[0];
for_each_nodebank(i, mi, node)
zhole_size[0] -= bank_pfn_size(&mi->bank[i]);
memcpy(zhole_size, zone_size, sizeof(zhole_size));
for_each_nodebank(i, mi, node) {
int idx = 0;
#ifdef CONFIG_HIGHMEM
if (mi->bank[i].highmem)
idx = ZONE_HIGHMEM;
#endif
zhole_size[idx] -= bank_pfn_size(&mi->bank[i]);
}
/*
* Adjust the sizes according to any special requirements for
@ -331,13 +346,13 @@ static void __init bootmem_free_node(int node, struct meminfo *mi)
*/
arch_adjust_zones(node, zone_size, zhole_size);
free_area_init_node(node, zone_size, start_pfn, zhole_size);
free_area_init_node(node, zone_size, min, zhole_size);
}
void __init bootmem_init(void)
{
struct meminfo *mi = &meminfo;
unsigned long memend_pfn = 0;
unsigned long min, max_low, max_high;
int node, initrd_node;
/*
@ -345,11 +360,29 @@ void __init bootmem_init(void)
*/
initrd_node = check_initrd(mi);
max_low = max_high = 0;
/*
* Run through each node initialising the bootmem allocator.
*/
for_each_node(node) {
unsigned long end_pfn = bootmem_init_node(node, mi);
unsigned long node_low, node_high;
find_node_limits(node, mi, &min, &node_low, &node_high);
if (node_low > max_low)
max_low = node_low;
if (node_high > max_high)
max_high = node_high;
/*
* If there is no memory in this node, ignore it.
* (We can't have nodes which have no lowmem)
*/
if (node_low == 0)
continue;
bootmem_init_node(node, mi, min, node_low);
/*
* Reserve any special node zero regions.
@ -362,12 +395,6 @@ void __init bootmem_init(void)
*/
if (node == initrd_node)
bootmem_reserve_initrd(node);
/*
* Remember the highest memory PFN.
*/
if (end_pfn > memend_pfn)
memend_pfn = end_pfn;
}
/*
@ -383,7 +410,7 @@ void __init bootmem_init(void)
for_each_node(node)
bootmem_free_node(node, mi);
high_memory = __va((memend_pfn << PAGE_SHIFT) - 1) + 1;
high_memory = __va((max_low << PAGE_SHIFT) - 1) + 1;
/*
* This doesn't seem to be used by the Linux memory manager any
@ -393,7 +420,8 @@ void __init bootmem_init(void)
* Note: max_low_pfn and max_pfn reflect the number of _pages_ in
* the system, not the maximum PFN.
*/
max_pfn = max_low_pfn = memend_pfn - PHYS_PFN_OFFSET;
max_low_pfn = max_low - PHYS_PFN_OFFSET;
max_pfn = max_high - PHYS_PFN_OFFSET;
}
static inline int free_area(unsigned long pfn, unsigned long end, char *s)

View File

@ -687,13 +687,19 @@ __early_param("vmalloc=", early_vmalloc);
static void __init sanity_check_meminfo(void)
{
int i, j;
int i, j, highmem = 0;
for (i = 0, j = 0; i < meminfo.nr_banks; i++) {
struct membank *bank = &meminfo.bank[j];
*bank = meminfo.bank[i];
#ifdef CONFIG_HIGHMEM
if (__va(bank->start) > VMALLOC_MIN ||
__va(bank->start) < (void *)PAGE_OFFSET)
highmem = 1;
bank->highmem = highmem;
/*
* Split those memory banks which are partially overlapping
* the vmalloc area greatly simplifying things later.
@ -714,6 +720,7 @@ static void __init sanity_check_meminfo(void)
i++;
bank[1].size -= VMALLOC_MIN - __va(bank->start);
bank[1].start = __pa(VMALLOC_MIN - 1) + 1;
bank[1].highmem = highmem = 1;
j++;
}
bank->size = VMALLOC_MIN - __va(bank->start);

View File

@ -78,10 +78,10 @@ static int omap_target(struct cpufreq_policy *policy,
/* Ensure desired rate is within allowed range. Some govenors
* (ondemand) will just pass target_freq=0 to get the minimum. */
if (target_freq < policy->cpuinfo.min_freq)
target_freq = policy->cpuinfo.min_freq;
if (target_freq > policy->cpuinfo.max_freq)
target_freq = policy->cpuinfo.max_freq;
if (target_freq < policy->min)
target_freq = policy->min;
if (target_freq > policy->max)
target_freq = policy->max;
freqs.old = omap_getspeed(0);
freqs.new = clk_round_rate(mpu_clk, target_freq * 1000) / 1000;

View File

@ -946,7 +946,9 @@ void omap_start_dma(int lch)
cur_lch = next_lch;
} while (next_lch != -1);
} else if (cpu_class_is_omap2()) {
} else if (cpu_is_omap242x() ||
(cpu_is_omap243x() && omap_type() <= OMAP2430_REV_ES1_0)) {
/* Errata: Need to write lch even if not using chaining */
dma_write(lch, CLNK_CTRL(lch));
}

View File

@ -476,14 +476,12 @@ static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
__raw_writel(l, reg);
}
static int __omap_get_gpio_datain(int gpio)
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
struct gpio_bank *bank;
void __iomem *reg;
if (check_gpio(gpio) < 0)
return -EINVAL;
bank = get_gpio_bank(gpio);
reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
@ -524,6 +522,53 @@ static int __omap_get_gpio_datain(int gpio)
& (1 << get_gpio_index(gpio))) != 0;
}
static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
{
void __iomem *reg;
if (check_gpio(gpio) < 0)
return -EINVAL;
reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
case METHOD_MPUIO:
reg += OMAP_MPUIO_OUTPUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP15XX
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DATA_OUTPUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP16XX
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DATAOUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP730
case METHOD_GPIO_730:
reg += OMAP730_GPIO_DATA_OUTPUT;
break;
#endif
#ifdef CONFIG_ARCH_OMAP850
case METHOD_GPIO_850:
reg += OMAP850_GPIO_DATA_OUTPUT;
break;
#endif
#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
defined(CONFIG_ARCH_OMAP4)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_DATAOUT;
break;
#endif
default:
return -EINVAL;
}
return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
}
#define MOD_REG_BIT(reg, bit_mask, set) \
do { \
int l = __raw_readl(base + reg); \
@ -1189,6 +1234,7 @@ static void gpio_mask_irq(unsigned int irq)
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 0);
_set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
}
static void gpio_unmask_irq(unsigned int irq)
@ -1196,6 +1242,11 @@ static void gpio_unmask_irq(unsigned int irq)
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
unsigned int irq_mask = 1 << get_gpio_index(gpio);
struct irq_desc *desc = irq_to_desc(irq);
u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK;
if (trigger)
_set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
/* For level-triggered GPIOs, the clearing must be done after
* the HW source is cleared, thus after the handler has run */
@ -1350,9 +1401,49 @@ static int gpio_input(struct gpio_chip *chip, unsigned offset)
return 0;
}
static int gpio_is_input(struct gpio_bank *bank, int mask)
{
void __iomem *reg = bank->base;
switch (bank->method) {
case METHOD_MPUIO:
reg += OMAP_MPUIO_IO_CNTL;
break;
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DIRECTION;
break;
case METHOD_GPIO_730:
reg += OMAP730_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_850:
reg += OMAP850_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_OE;
break;
}
return __raw_readl(reg) & mask;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
return __omap_get_gpio_datain(chip->base + offset);
struct gpio_bank *bank;
void __iomem *reg;
int gpio;
u32 mask;
gpio = chip->base + offset;
bank = get_gpio_bank(gpio);
reg = bank->base;
mask = 1 << get_gpio_index(gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
static int gpio_output(struct gpio_chip *chip, unsigned offset, int value)
@ -1886,34 +1977,6 @@ arch_initcall(omap_gpio_sysinit);
#include <linux/debugfs.h>
#include <linux/seq_file.h>
static int gpio_is_input(struct gpio_bank *bank, int mask)
{
void __iomem *reg = bank->base;
switch (bank->method) {
case METHOD_MPUIO:
reg += OMAP_MPUIO_IO_CNTL;
break;
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_1610:
reg += OMAP1610_GPIO_DIRECTION;
break;
case METHOD_GPIO_730:
reg += OMAP730_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_850:
reg += OMAP850_GPIO_DIR_CONTROL;
break;
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_OE;
break;
}
return __raw_readl(reg) & mask;
}
static int dbg_gpio_show(struct seq_file *s, void *unused)
{
unsigned i, j, gpio;

View File

@ -20,6 +20,8 @@ struct clockdomain;
struct clkops {
int (*enable)(struct clk *);
void (*disable)(struct clk *);
void (*find_idlest)(struct clk *, void __iomem **, u8 *);
void (*find_companion)(struct clk *, void __iomem **, u8 *);
};
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \

Some files were not shown because too many files have changed in this diff Show More