diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 2f4a598ba67e..31632ac1ca7c 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -544,112 +544,6 @@ static inline void omap_init_aes(void) { }
 
 /*-------------------------------------------------------------------------*/
 
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
-
-#define MMCHS_SYSCONFIG			0x0010
-#define MMCHS_SYSCONFIG_SWRESET		(1 << 1)
-#define MMCHS_SYSSTATUS			0x0014
-#define MMCHS_SYSSTATUS_RESETDONE	(1 << 0)
-
-static struct platform_device dummy_pdev = {
-	.dev = {
-		.bus = &platform_bus_type,
-	},
-};
-
-/**
- * omap_hsmmc_reset() - Full reset of each HS-MMC controller
- *
- * Ensure that each MMC controller is fully reset.  Controllers
- * left in an unknown state (by bootloader) may prevent retention
- * or OFF-mode.  This is especially important in cases where the
- * MMC driver is not enabled, _or_ built as a module.
- *
- * In order for reset to work, interface, functional and debounce
- * clocks must be enabled.  The debounce clock comes from func_32k_clk
- * and is not under SW control, so we only enable i- and f-clocks.
- **/
-static void __init omap_hsmmc_reset(void)
-{
-	u32 i, nr_controllers;
-	struct clk *iclk, *fclk;
-
-	if (cpu_is_omap242x())
-		return;
-
-	nr_controllers = cpu_is_omap44xx() ? OMAP44XX_NR_MMC :
-		(cpu_is_omap34xx() ? OMAP34XX_NR_MMC : OMAP24XX_NR_MMC);
-
-	for (i = 0; i < nr_controllers; i++) {
-		u32 v, base = 0;
-		struct device *dev = &dummy_pdev.dev;
-
-		switch (i) {
-		case 0:
-			base = OMAP2_MMC1_BASE;
-			break;
-		case 1:
-			base = OMAP2_MMC2_BASE;
-			break;
-		case 2:
-			base = OMAP3_MMC3_BASE;
-			break;
-		case 3:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC4_BASE;
-			break;
-		case 4:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC5_BASE;
-			break;
-		}
-
-		if (cpu_is_omap44xx())
-			base += OMAP4_MMC_REG_OFFSET;
-
-		dummy_pdev.id = i;
-		dev_set_name(&dummy_pdev.dev, "mmci-omap-hs.%d", i);
-		iclk = clk_get(dev, "ick");
-		if (IS_ERR(iclk))
-			goto err1;
-		if (clk_enable(iclk))
-			goto err2;
-
-		fclk = clk_get(dev, "fck");
-		if (IS_ERR(fclk))
-			goto err3;
-		if (clk_enable(fclk))
-			goto err4;
-
-		omap_writel(MMCHS_SYSCONFIG_SWRESET, base + MMCHS_SYSCONFIG);
-		v = omap_readl(base + MMCHS_SYSSTATUS);
-		while (!(omap_readl(base + MMCHS_SYSSTATUS) &
-			 MMCHS_SYSSTATUS_RESETDONE))
-			cpu_relax();
-
-		clk_disable(fclk);
-		clk_put(fclk);
-		clk_disable(iclk);
-		clk_put(iclk);
-	}
-	return;
-
-err4:
-	clk_put(fclk);
-err3:
-	clk_disable(iclk);
-err2:
-	clk_put(iclk);
-err1:
-	printk(KERN_WARNING "%s: Unable to enable clocks for MMC%d, "
-			    "cannot reset.\n",  __func__, i);
-}
-#else
-static inline void omap_hsmmc_reset(void) {}
-#endif
-
 #if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
 
 static inline void omap242x_mmc_mux(struct omap_mmc_platform_data
@@ -706,67 +600,6 @@ void __init omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
 
 #endif
 
-#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-
-void __init omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
-			int nr_controllers)
-{
-	int i;
-	char *name;
-
-	for (i = 0; i < nr_controllers; i++) {
-		unsigned long base, size;
-		unsigned int irq = 0;
-
-		if (!mmc_data[i])
-			continue;
-
-		switch (i) {
-		case 0:
-			base = OMAP2_MMC1_BASE;
-			irq = INT_24XX_MMC_IRQ;
-			break;
-		case 1:
-			base = OMAP2_MMC2_BASE;
-			irq = INT_24XX_MMC2_IRQ;
-			break;
-		case 2:
-			if (!cpu_is_omap44xx() && !cpu_is_omap34xx())
-				return;
-			base = OMAP3_MMC3_BASE;
-			irq = INT_34XX_MMC3_IRQ;
-			break;
-		case 3:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC4_BASE;
-			irq = OMAP44XX_IRQ_MMC4;
-			break;
-		case 4:
-			if (!cpu_is_omap44xx())
-				return;
-			base = OMAP4_MMC5_BASE;
-			irq = OMAP44XX_IRQ_MMC5;
-			break;
-		default:
-			continue;
-		}
-
-		if (cpu_is_omap44xx()) {
-			if (i < 3)
-				irq += OMAP44XX_IRQ_GIC_START;
-			size = OMAP4_HSMMC_SIZE;
-			name = "mmci-omap-hs";
-		} else {
-			size = OMAP3_HSMMC_SIZE;
-			name = "mmci-omap-hs";
-		}
-		omap_mmc_add(name, i, base, size, irq, mmc_data[i]);
-	};
-}
-
-#endif
-
 /*-------------------------------------------------------------------------*/
 
 #if defined(CONFIG_HDQ_MASTER_OMAP) || defined(CONFIG_HDQ_MASTER_OMAP_MODULE)
@@ -836,7 +669,6 @@ static int __init omap2_init_devices(void)
 	 * please keep these calls, and their implementations above,
 	 * in alphabetical order so they're easier to sort through.
 	 */
-	omap_hsmmc_reset();
 	omap_init_audio();
 	omap_init_camera();
 	omap_init_mbox();
diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index 1348ac3d60e3..d492bc4d3428 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -17,6 +17,7 @@
 #include <plat/mmc.h>
 #include <plat/omap-pm.h>
 #include <plat/mux.h>
+#include <plat/omap_device.h>
 
 #include "mux.h"
 #include "hsmmc.h"
@@ -30,10 +31,6 @@ static u16 control_mmc1;
 
 #define HSMMC_NAME_LEN	9
 
-static struct hsmmc_controller {
-	char				name[HSMMC_NAME_LEN + 1];
-} hsmmc[OMAP34XX_NR_MMC];
-
 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
 
 static int hsmmc_get_context_loss(struct device *dev)
@@ -287,13 +284,203 @@ static inline void omap_hsmmc_mux(struct omap_mmc_platform_data *mmc_controller,
 	}
 }
 
-static struct omap_mmc_platform_data *hsmmc_data[OMAP34XX_NR_MMC] __initdata;
+static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
+					struct omap_mmc_platform_data *mmc)
+{
+	char *hc_name;
+
+	hc_name = kzalloc(sizeof(char) * (HSMMC_NAME_LEN + 1), GFP_KERNEL);
+	if (!hc_name) {
+		pr_err("Cannot allocate memory for controller slot name\n");
+		kfree(hc_name);
+		return -ENOMEM;
+	}
+
+	if (c->name)
+		strncpy(hc_name, c->name, HSMMC_NAME_LEN);
+	else
+		snprintf(hc_name, (HSMMC_NAME_LEN + 1), "mmc%islot%i",
+								c->mmc, 1);
+	mmc->slots[0].name = hc_name;
+	mmc->nr_slots = 1;
+	mmc->slots[0].caps = c->caps;
+	mmc->slots[0].internal_clock = !c->ext_clock;
+	mmc->dma_mask = 0xffffffff;
+	if (cpu_is_omap44xx())
+		mmc->reg_offset = OMAP4_MMC_REG_OFFSET;
+	else
+		mmc->reg_offset = 0;
+
+	mmc->get_context_loss_count = hsmmc_get_context_loss;
+
+	mmc->slots[0].switch_pin = c->gpio_cd;
+	mmc->slots[0].gpio_wp = c->gpio_wp;
+
+	mmc->slots[0].remux = c->remux;
+	mmc->slots[0].init_card = c->init_card;
+
+	if (c->cover_only)
+		mmc->slots[0].cover = 1;
+
+	if (c->nonremovable)
+		mmc->slots[0].nonremovable = 1;
+
+	if (c->power_saving)
+		mmc->slots[0].power_saving = 1;
+
+	if (c->no_off)
+		mmc->slots[0].no_off = 1;
+
+	if (c->vcc_aux_disable_is_sleep)
+		mmc->slots[0].vcc_aux_disable_is_sleep = 1;
+
+	/*
+	 * NOTE:  MMC slots should have a Vcc regulator set up.
+	 * This may be from a TWL4030-family chip, another
+	 * controllable regulator, or a fixed supply.
+	 *
+	 * temporary HACK: ocr_mask instead of fixed supply
+	 */
+	mmc->slots[0].ocr_mask = c->ocr_mask;
+
+	if (cpu_is_omap3517() || cpu_is_omap3505())
+		mmc->slots[0].set_power = nop_mmc_set_power;
+	else
+		mmc->slots[0].features |= HSMMC_HAS_PBIAS;
+
+	if (cpu_is_omap44xx() && (omap_rev() > OMAP4430_REV_ES1_0))
+		mmc->slots[0].features |= HSMMC_HAS_UPDATED_RESET;
+
+	switch (c->mmc) {
+	case 1:
+		if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
+			/* on-chip level shifting via PBIAS0/PBIAS1 */
+			if (cpu_is_omap44xx()) {
+				mmc->slots[0].before_set_reg =
+						omap4_hsmmc1_before_set_reg;
+				mmc->slots[0].after_set_reg =
+						omap4_hsmmc1_after_set_reg;
+			} else {
+				mmc->slots[0].before_set_reg =
+						omap_hsmmc1_before_set_reg;
+				mmc->slots[0].after_set_reg =
+						omap_hsmmc1_after_set_reg;
+			}
+		}
+
+		/* OMAP3630 HSMMC1 supports only 4-bit */
+		if (cpu_is_omap3630() &&
+				(c->caps & MMC_CAP_8_BIT_DATA)) {
+			c->caps &= ~MMC_CAP_8_BIT_DATA;
+			c->caps |= MMC_CAP_4_BIT_DATA;
+			mmc->slots[0].caps = c->caps;
+		}
+		break;
+	case 2:
+		if (c->ext_clock)
+			c->transceiver = 1;
+		if (c->transceiver && (c->caps & MMC_CAP_8_BIT_DATA)) {
+			c->caps &= ~MMC_CAP_8_BIT_DATA;
+			c->caps |= MMC_CAP_4_BIT_DATA;
+		}
+		/* FALLTHROUGH */
+	case 3:
+		if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
+			/* off-chip level shifting, or none */
+			mmc->slots[0].before_set_reg = hsmmc23_before_set_reg;
+			mmc->slots[0].after_set_reg = NULL;
+		}
+		break;
+	case 4:
+	case 5:
+		mmc->slots[0].before_set_reg = NULL;
+		mmc->slots[0].after_set_reg = NULL;
+		break;
+	default:
+		pr_err("MMC%d configuration not supported!\n", c->mmc);
+		kfree(hc_name);
+		return -ENODEV;
+	}
+	return 0;
+}
+
+static struct omap_device_pm_latency omap_hsmmc_latency[] = {
+	[0] = {
+		.deactivate_func = omap_device_idle_hwmods,
+		.activate_func	 = omap_device_enable_hwmods,
+		.flags		 = OMAP_DEVICE_LATENCY_AUTO_ADJUST,
+	},
+	/*
+	 * XXX There should also be an entry here to power off/on the
+	 * MMC regulators/PBIAS cells, etc.
+	 */
+};
+
+#define MAX_OMAP_MMC_HWMOD_NAME_LEN		16
+
+void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr)
+{
+	struct omap_hwmod *oh;
+	struct omap_device *od;
+	struct omap_device_pm_latency *ohl;
+	char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN];
+	struct omap_mmc_platform_data *mmc_data;
+	struct omap_mmc_dev_attr *mmc_dev_attr;
+	char *name;
+	int l;
+	int ohl_cnt = 0;
+
+	mmc_data = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
+	if (!mmc_data) {
+		pr_err("Cannot allocate memory for mmc device!\n");
+		goto done;
+	}
+
+	if (omap_hsmmc_pdata_init(hsmmcinfo, mmc_data) < 0) {
+		pr_err("%s fails!\n", __func__);
+		goto done;
+	}
+	omap_hsmmc_mux(mmc_data, (ctrl_nr - 1));
+
+	name = "mmci-omap-hs";
+	ohl = omap_hsmmc_latency;
+	ohl_cnt = ARRAY_SIZE(omap_hsmmc_latency);
+
+	l = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN,
+		     "mmc%d", ctrl_nr);
+	WARN(l >= MAX_OMAP_MMC_HWMOD_NAME_LEN,
+	     "String buffer overflow in MMC%d device setup\n", ctrl_nr);
+	oh = omap_hwmod_lookup(oh_name);
+	if (!oh) {
+		pr_err("Could not look up %s\n", oh_name);
+		kfree(mmc_data->slots[0].name);
+		goto done;
+	}
+
+	if (oh->dev_attr != NULL) {
+		mmc_dev_attr = oh->dev_attr;
+		mmc_data->controller_flags = mmc_dev_attr->flags;
+	}
+
+	od = omap_device_build(name, ctrl_nr - 1, oh, mmc_data,
+		sizeof(struct omap_mmc_platform_data), ohl, ohl_cnt, false);
+	if (IS_ERR(od)) {
+		WARN(1, "Cant build omap_device for %s:%s.\n", name, oh->name);
+		kfree(mmc_data->slots[0].name);
+		goto done;
+	}
+	/*
+	 * return device handle to board setup code
+	 * required to populate for regulator framework structure
+	 */
+	hsmmcinfo->dev = &od->pdev.dev;
+
+done:
+	kfree(mmc_data);
+}
 
 void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
 {
-	struct omap2_hsmmc_info *c;
-	int nr_hsmmc = ARRAY_SIZE(hsmmc_data);
-	int i;
 	u32 reg;
 
 	if (!cpu_is_omap44xx()) {
@@ -319,148 +506,9 @@ void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
 		omap4_ctrl_pad_writel(reg, control_mmc1);
 	}
 
-	for (c = controllers; c->mmc; c++) {
-		struct hsmmc_controller *hc = hsmmc + c->mmc - 1;
-		struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
+	for (; controllers->mmc; controllers++)
+		omap_init_hsmmc(controllers, controllers->mmc);
 
-		if (!c->mmc || c->mmc > nr_hsmmc) {
-			pr_debug("MMC%d: no such controller\n", c->mmc);
-			continue;
-		}
-		if (mmc) {
-			pr_debug("MMC%d: already configured\n", c->mmc);
-			continue;
-		}
-
-		mmc = kzalloc(sizeof(struct omap_mmc_platform_data),
-			      GFP_KERNEL);
-		if (!mmc) {
-			pr_err("Cannot allocate memory for mmc device!\n");
-			goto done;
-		}
-
-		if (c->name)
-			strncpy(hc->name, c->name, HSMMC_NAME_LEN);
-		else
-			snprintf(hc->name, ARRAY_SIZE(hc->name),
-				"mmc%islot%i", c->mmc, 1);
-		mmc->slots[0].name = hc->name;
-		mmc->nr_slots = 1;
-		mmc->slots[0].caps = c->caps;
-		mmc->slots[0].internal_clock = !c->ext_clock;
-		mmc->dma_mask = 0xffffffff;
-		if (cpu_is_omap44xx())
-			mmc->reg_offset = OMAP4_MMC_REG_OFFSET;
-		else
-			mmc->reg_offset = 0;
-
-		mmc->get_context_loss_count = hsmmc_get_context_loss;
-
-		mmc->slots[0].switch_pin = c->gpio_cd;
-		mmc->slots[0].gpio_wp = c->gpio_wp;
-
-		mmc->slots[0].remux = c->remux;
-		mmc->slots[0].init_card = c->init_card;
-
-		if (c->cover_only)
-			mmc->slots[0].cover = 1;
-
-		if (c->nonremovable)
-			mmc->slots[0].nonremovable = 1;
-
-		if (c->power_saving)
-			mmc->slots[0].power_saving = 1;
-
-		if (c->no_off)
-			mmc->slots[0].no_off = 1;
-
-		if (c->vcc_aux_disable_is_sleep)
-			mmc->slots[0].vcc_aux_disable_is_sleep = 1;
-
-		/* NOTE:  MMC slots should have a Vcc regulator set up.
-		 * This may be from a TWL4030-family chip, another
-		 * controllable regulator, or a fixed supply.
-		 *
-		 * temporary HACK: ocr_mask instead of fixed supply
-		 */
-		mmc->slots[0].ocr_mask = c->ocr_mask;
-
-		if (cpu_is_omap3517() || cpu_is_omap3505())
-			mmc->slots[0].set_power = nop_mmc_set_power;
-		else
-			mmc->slots[0].features |= HSMMC_HAS_PBIAS;
-
-		if (cpu_is_omap44xx() && (omap_rev() > OMAP4430_REV_ES1_0))
-			mmc->slots[0].features |= HSMMC_HAS_UPDATED_RESET;
-
-		switch (c->mmc) {
-		case 1:
-			if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
-				/* on-chip level shifting via PBIAS0/PBIAS1 */
-				if (cpu_is_omap44xx()) {
-					mmc->slots[0].before_set_reg =
-						omap4_hsmmc1_before_set_reg;
-					mmc->slots[0].after_set_reg =
-						omap4_hsmmc1_after_set_reg;
-				} else {
-					mmc->slots[0].before_set_reg =
-						omap_hsmmc1_before_set_reg;
-					mmc->slots[0].after_set_reg =
-						omap_hsmmc1_after_set_reg;
-				}
-			}
-
-			/* Omap3630 HSMMC1 supports only 4-bit */
-			if (cpu_is_omap3630() &&
-					(c->caps & MMC_CAP_8_BIT_DATA)) {
-				c->caps &= ~MMC_CAP_8_BIT_DATA;
-				c->caps |= MMC_CAP_4_BIT_DATA;
-				mmc->slots[0].caps = c->caps;
-			}
-			break;
-		case 2:
-			if (c->ext_clock)
-				c->transceiver = 1;
-			if (c->transceiver && (c->caps & MMC_CAP_8_BIT_DATA)) {
-				c->caps &= ~MMC_CAP_8_BIT_DATA;
-				c->caps |= MMC_CAP_4_BIT_DATA;
-			}
-			/* FALLTHROUGH */
-		case 3:
-			if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
-				/* off-chip level shifting, or none */
-				mmc->slots[0].before_set_reg = hsmmc23_before_set_reg;
-				mmc->slots[0].after_set_reg = NULL;
-			}
-			break;
-		case 4:
-		case 5:
-			mmc->slots[0].before_set_reg = NULL;
-			mmc->slots[0].after_set_reg = NULL;
-			break;
-		default:
-			pr_err("MMC%d configuration not supported!\n", c->mmc);
-			kfree(mmc);
-			continue;
-		}
-		hsmmc_data[c->mmc - 1] = mmc;
-		omap_hsmmc_mux(hsmmc_data[c->mmc - 1], (c->mmc - 1));
-	}
-
-	omap2_init_mmc(hsmmc_data, OMAP34XX_NR_MMC);
-
-	/* pass the device nodes back to board setup code */
-	for (c = controllers; c->mmc; c++) {
-		struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
-
-		if (!c->mmc || c->mmc > nr_hsmmc)
-			continue;
-		c->dev = mmc->dev;
-	}
-
-done:
-	for (i = 0; i < nr_hsmmc; i++)
-		kfree(hsmmc_data[i]);
 }
 
 #endif
diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
index a7afab095716..f38fef9f1310 100644
--- a/arch/arm/plat-omap/include/plat/mmc.h
+++ b/arch/arm/plat-omap/include/plat/mmc.h
@@ -24,22 +24,10 @@
 #define OMAP1_MMC2_BASE		0xfffb7c00	/* omap16xx only */
 
 #define OMAP24XX_NR_MMC		2
-#define OMAP34XX_NR_MMC		3
-#define OMAP44XX_NR_MMC		5
 #define OMAP2420_MMC_SIZE	OMAP1_MMC_SIZE
-#define OMAP3_HSMMC_SIZE	0x200
-#define OMAP4_HSMMC_SIZE	0x1000
 #define OMAP2_MMC1_BASE		0x4809c000
-#define OMAP2_MMC2_BASE		0x480b4000
-#define OMAP3_MMC3_BASE		0x480ad000
-#define OMAP4_MMC4_BASE		0x480d1000
-#define OMAP4_MMC5_BASE		0x480d5000
+
 #define OMAP4_MMC_REG_OFFSET	0x100
-#define HSMMC5			(1 << 4)
-#define HSMMC4			(1 << 3)
-#define HSMMC3			(1 << 2)
-#define HSMMC2			(1 << 1)
-#define HSMMC1			(1 << 0)
 
 #define OMAP_MMC_MAX_SLOTS	2
 
@@ -169,8 +157,6 @@ extern void omap_mmc_notify_cover_event(struct device *dev, int slot,
 void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
 				int nr_controllers);
 void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data);
-void omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
-				int nr_controllers);
 int omap_mmc_add(const char *name, int id, unsigned long base,
 				unsigned long size, unsigned int irq,
 				struct omap_mmc_platform_data *data);
@@ -182,10 +168,6 @@ static inline void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
 static inline void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
 {
 }
-static inline void omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
-				int nr_controllers)
-{
-}
 static inline int omap_mmc_add(const char *name, int id, unsigned long base,
 				unsigned long size, unsigned int irq,
 				struct omap_mmc_platform_data *data)
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 8c42573f42ea..d0bd2b43393a 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -1571,7 +1571,7 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		break;
 	}
 
-	if (host->id == OMAP_MMC1_DEVID) {
+	if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
 		/* Only MMC1 can interface at 3V without some flavor
 		 * of external transceiver; but they all handle 1.8V.
 		 */
@@ -1663,7 +1663,7 @@ static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host)
 	u32 hctl, capa, value;
 
 	/* Only MMC1 supports 3.0V */
-	if (host->id == OMAP_MMC1_DEVID) {
+	if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
 		hctl = SDVS30;
 		capa = VS30 | VS18;
 	} else {