Merge branch 'arm64-for-5.1' into arm64-for-5.1-2
This commit is contained in:
Andy Gross
commit
40d8e6dabf
|
|
@ -644,6 +644,8 @@
|
|||
l11 {
|
||||
regulator-min-microvolt = <1750000>;
|
||||
regulator-max-microvolt = <3337000>;
|
||||
regulator-allow-set-load;
|
||||
regulator-system-load = <200000>;
|
||||
};
|
||||
|
||||
l12 {
|
||||
|
|
|
|||
|
|
@ -139,7 +139,7 @@
|
|||
};
|
||||
|
||||
pinconf {
|
||||
pins = "gpio4", "gpiio5", "gpio6", "gpio7";
|
||||
pins = "gpio4", "gpio5", "gpio6", "gpio7";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
|
|
|||
|
|
@ -32,6 +32,12 @@
|
|||
bias-pull-up;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "qcom,pm8916-wdt";
|
||||
interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>;
|
||||
timeout-sec = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
pm8916_gpios: gpios@c000 {
|
||||
|
|
|
|||
|
|
@ -3,6 +3,32 @@
|
|||
|
||||
#include <dt-bindings/spmi/spmi.h>
|
||||
#include <dt-bindings/input/linux-event-codes.h>
|
||||
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
||||
#include <dt-bindings/thermal/thermal.h>
|
||||
|
||||
/ {
|
||||
thermal-zones {
|
||||
pms405 {
|
||||
polling-delay-passive = <250>;
|
||||
polling-delay = <1000>;
|
||||
|
||||
thermal-sensors = <&pms405_temp>;
|
||||
|
||||
trips {
|
||||
pms405_alert0: pms405-alert0 {
|
||||
temperature = <105000>;
|
||||
hysteresis = <2000>;
|
||||
type = "passive";
|
||||
};
|
||||
pms405_crit: pms405-crit {
|
||||
temperature = <125000>;
|
||||
hysteresis = <2000>;
|
||||
type = "critical";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spmi_bus {
|
||||
pms405_0: pms405@0 {
|
||||
|
|
@ -45,6 +71,59 @@
|
|||
};
|
||||
};
|
||||
|
||||
pms405_temp: temp-alarm@2400 {
|
||||
compatible = "qcom,spmi-temp-alarm";
|
||||
reg = <0x2400>;
|
||||
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
|
||||
io-channels = <&pms405_adc ADC5_DIE_TEMP>;
|
||||
io-channel-names = "thermal";
|
||||
#thermal-sensor-cells = <0>;
|
||||
};
|
||||
|
||||
pms405_adc: adc@3100 {
|
||||
compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2";
|
||||
reg = <0x3100>;
|
||||
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
#io-channel-cells = <1>;
|
||||
|
||||
ref_gnd {
|
||||
reg = <ADC5_REF_GND>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
|
||||
vref_1p25 {
|
||||
reg = <ADC5_1P25VREF>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
|
||||
vph_pwr {
|
||||
reg = <ADC5_VPH_PWR>;
|
||||
qcom,pre-scaling = <1 3>;
|
||||
};
|
||||
|
||||
die_temp {
|
||||
reg = <ADC5_DIE_TEMP>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
|
||||
xo_therm_100k_pu {
|
||||
reg = <ADC5_XO_THERM_100K_PU>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
|
||||
amux_thm1_100k_pu {
|
||||
reg = <ADC5_AMUX_THM1_100K_PU>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
|
||||
amux_thm3_100k_pu {
|
||||
reg = <ADC5_AMUX_THM3_100K_PU>;
|
||||
qcom,pre-scaling = <1 1>;
|
||||
};
|
||||
};
|
||||
|
||||
rtc@6000 {
|
||||
compatible = "qcom,pm8941-rtc";
|
||||
reg = <0x6000>;
|
||||
|
|
|
|||
|
|
@ -127,6 +127,7 @@
|
|||
status = "ok";
|
||||
|
||||
mmc-ddr-1_8v;
|
||||
mmc-hs400-1_8v;
|
||||
bus-width = <8>;
|
||||
non-removable;
|
||||
|
||||
|
|
@ -186,3 +187,7 @@
|
|||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
};
|
||||
|
|
|
|||
|
|
@ -346,6 +346,26 @@
|
|||
status = "okay";
|
||||
};
|
||||
|
||||
wifi: wifi@a000000 {
|
||||
compatible = "qcom,wcn3990-wifi";
|
||||
reg = <0xa000000 0x800000>;
|
||||
reg-names = "membase";
|
||||
memory-region = <&wlan_msa_mem>;
|
||||
interrupts = <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
intc: interrupt-controller@b000000 {
|
||||
compatible = "qcom,msm-qgic2";
|
||||
interrupt-controller;
|
||||
|
|
|
|||
|
|
@ -7,6 +7,7 @@
|
|||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
|
||||
#include "sdm845.dtsi"
|
||||
|
||||
|
|
@ -358,14 +359,36 @@
|
|||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
gpio-reserved-ranges = <0 4>, <81 4>;
|
||||
&sdhc_2 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>;
|
||||
|
||||
vmmc-supply = <&vreg_l21a_2p95>;
|
||||
vqmmc-supply = <&vddpx_2>;
|
||||
|
||||
cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&uart9 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ufs_mem_hc {
|
||||
status = "okay";
|
||||
|
||||
vcc-supply = <&vreg_l20a_2p95>;
|
||||
vcc-max-microamp = <600000>;
|
||||
};
|
||||
|
||||
&ufs_mem_phy {
|
||||
status = "okay";
|
||||
|
||||
vdda-phy-supply = <&vdda_ufs1_core>;
|
||||
vdda-pll-supply = <&vdda_ufs1_1p2>;
|
||||
};
|
||||
|
||||
&usb_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
|
@ -450,3 +473,48 @@
|
|||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
gpio-reserved-ranges = <0 4>, <81 4>;
|
||||
|
||||
sdc2_clk: sdc2-clk {
|
||||
pinconf {
|
||||
pins = "sdc2_clk";
|
||||
bias-disable;
|
||||
|
||||
/*
|
||||
* It seems that mmc_test reports errors if drive
|
||||
* strength is not 16 on clk, cmd, and data pins.
|
||||
*/
|
||||
drive-strength = <16>;
|
||||
};
|
||||
};
|
||||
|
||||
sdc2_cmd: sdc2-cmd {
|
||||
pinconf {
|
||||
pins = "sdc2_cmd";
|
||||
bias-pull-up;
|
||||
drive-strength = <16>;
|
||||
};
|
||||
};
|
||||
|
||||
sdc2_data: sdc2-data {
|
||||
pinconf {
|
||||
pins = "sdc2_data";
|
||||
bias-pull-up;
|
||||
drive-strength = <16>;
|
||||
};
|
||||
};
|
||||
|
||||
sd_card_det_n: sd-card-det-n {
|
||||
pinmux {
|
||||
pins = "gpio126";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
pinconf {
|
||||
pins = "gpio126";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
|
|||
|
|
@ -99,6 +99,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x0>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 0>;
|
||||
next-level-cache = <&L2_0>;
|
||||
L2_0: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -114,6 +115,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x100>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 0>;
|
||||
next-level-cache = <&L2_100>;
|
||||
L2_100: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -126,6 +128,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x200>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 0>;
|
||||
next-level-cache = <&L2_200>;
|
||||
L2_200: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -138,6 +141,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x300>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 0>;
|
||||
next-level-cache = <&L2_300>;
|
||||
L2_300: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -150,6 +154,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x400>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 1>;
|
||||
next-level-cache = <&L2_400>;
|
||||
L2_400: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -162,6 +167,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x500>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 1>;
|
||||
next-level-cache = <&L2_500>;
|
||||
L2_500: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -174,6 +180,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x600>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 1>;
|
||||
next-level-cache = <&L2_600>;
|
||||
L2_600: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -186,6 +193,7 @@
|
|||
compatible = "qcom,kryo385";
|
||||
reg = <0x0 0x700>;
|
||||
enable-method = "psci";
|
||||
qcom,freq-domain = <&cpufreq_hw 1>;
|
||||
next-level-cache = <&L2_700>;
|
||||
L2_700: l2-cache {
|
||||
compatible = "cache";
|
||||
|
|
@ -981,6 +989,72 @@
|
|||
};
|
||||
};
|
||||
|
||||
ufs_mem_hc: ufshc@1d84000 {
|
||||
compatible = "qcom,sdm845-ufshc", "qcom,ufshc",
|
||||
"jedec,ufs-2.0";
|
||||
reg = <0x1d84000 0x2500>;
|
||||
interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
|
||||
phys = <&ufs_mem_phy_lanes>;
|
||||
phy-names = "ufsphy";
|
||||
lanes-per-direction = <2>;
|
||||
power-domains = <&gcc UFS_PHY_GDSC>;
|
||||
|
||||
iommus = <&apps_smmu 0x100 0xf>;
|
||||
|
||||
clock-names =
|
||||
"core_clk",
|
||||
"bus_aggr_clk",
|
||||
"iface_clk",
|
||||
"core_clk_unipro",
|
||||
"ref_clk",
|
||||
"tx_lane0_sync_clk",
|
||||
"rx_lane0_sync_clk",
|
||||
"rx_lane1_sync_clk";
|
||||
clocks =
|
||||
<&gcc GCC_UFS_PHY_AXI_CLK>,
|
||||
<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
|
||||
<&gcc GCC_UFS_PHY_AHB_CLK>,
|
||||
<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
|
||||
<&rpmhcc RPMH_CXO_CLK>,
|
||||
<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
|
||||
<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
|
||||
<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
|
||||
freq-table-hz =
|
||||
<50000000 200000000>,
|
||||
<0 0>,
|
||||
<0 0>,
|
||||
<37500000 150000000>,
|
||||
<0 0>,
|
||||
<0 0>,
|
||||
<0 0>,
|
||||
<0 0>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ufs_mem_phy: phy@1d87000 {
|
||||
compatible = "qcom,sdm845-qmp-ufs-phy";
|
||||
reg = <0x1d87000 0x18c>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
clock-names = "ref",
|
||||
"ref_aux";
|
||||
clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
|
||||
<&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
|
||||
|
||||
status = "disabled";
|
||||
|
||||
ufs_mem_phy_lanes: lanes@1d87400 {
|
||||
reg = <0x1d87400 0x108>,
|
||||
<0x1d87600 0x1e0>,
|
||||
<0x1d87c00 0x1dc>,
|
||||
<0x1d87800 0x108>,
|
||||
<0x1d87a00 0x1e0>;
|
||||
#phy-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
tcsr_mutex_regs: syscon@1f40000 {
|
||||
compatible = "syscon";
|
||||
reg = <0x1f40000 0x40000>;
|
||||
|
|
@ -1348,6 +1422,21 @@
|
|||
};
|
||||
};
|
||||
|
||||
sdhc_2: sdhci@8804000 {
|
||||
compatible = "qcom,sdm845-sdhci", "qcom,sdhci-msm-v5";
|
||||
reg = <0x8804000 0x1000>;
|
||||
|
||||
interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "hc_irq", "pwr_irq";
|
||||
|
||||
clocks = <&gcc GCC_SDCC2_AHB_CLK>,
|
||||
<&gcc GCC_SDCC2_APPS_CLK>;
|
||||
clock-names = "iface", "core";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
usb_1_hsphy: phy@88e2000 {
|
||||
compatible = "qcom,sdm845-qusb2-phy";
|
||||
reg = <0x88e2000 0x400>;
|
||||
|
|
@ -1399,10 +1488,12 @@
|
|||
<&gcc GCC_USB3_PHY_PRIM_BCR>;
|
||||
reset-names = "phy", "common";
|
||||
|
||||
usb_1_ssphy: lane@88e9200 {
|
||||
usb_1_ssphy: lanes@88e9200 {
|
||||
reg = <0x88e9200 0x128>,
|
||||
<0x88e9400 0x200>,
|
||||
<0x88e9c00 0x218>,
|
||||
<0x88e9600 0x128>,
|
||||
<0x88e9800 0x200>,
|
||||
<0x88e9a00 0x100>;
|
||||
#phy-cells = <0>;
|
||||
clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
|
||||
|
|
@ -1526,6 +1617,209 @@
|
|||
};
|
||||
};
|
||||
|
||||
mdss: mdss@ae00000 {
|
||||
compatible = "qcom,sdm845-mdss";
|
||||
reg = <0x0ae00000 0x1000>;
|
||||
reg-names = "mdss";
|
||||
|
||||
power-domains = <&dispcc MDSS_GDSC>;
|
||||
|
||||
clocks = <&gcc GCC_DISP_AHB_CLK>,
|
||||
<&gcc GCC_DISP_AXI_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_MDP_CLK>;
|
||||
clock-names = "iface", "bus", "core";
|
||||
|
||||
assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
|
||||
assigned-clock-rates = <300000000>;
|
||||
|
||||
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
|
||||
iommus = <&apps_smmu 0x880 0x8>,
|
||||
<&apps_smmu 0xc80 0x8>;
|
||||
|
||||
status = "disabled";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
mdss_mdp: mdp@ae01000 {
|
||||
compatible = "qcom,sdm845-dpu";
|
||||
reg = <0x0ae01000 0x8f000>,
|
||||
<0x0aeb0000 0x2008>;
|
||||
reg-names = "mdp", "vbif";
|
||||
|
||||
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_AXI_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_MDP_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
|
||||
clock-names = "iface", "bus", "core", "vsync";
|
||||
|
||||
assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
|
||||
assigned-clock-rates = <300000000>,
|
||||
<19200000>;
|
||||
|
||||
interrupt-parent = <&mdss>;
|
||||
interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
status = "disabled";
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
dpu_intf1_out: endpoint {
|
||||
remote-endpoint = <&dsi0_in>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
dpu_intf2_out: endpoint {
|
||||
remote-endpoint = <&dsi1_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
dsi0: dsi@ae94000 {
|
||||
compatible = "qcom,mdss-dsi-ctrl";
|
||||
reg = <0xae94000 0x400>;
|
||||
reg-names = "dsi_ctrl";
|
||||
|
||||
interrupt-parent = <&mdss>;
|
||||
interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_PCLK0_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_ESC0_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_AHB_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_AXI_CLK>;
|
||||
clock-names = "byte",
|
||||
"byte_intf",
|
||||
"pixel",
|
||||
"core",
|
||||
"iface",
|
||||
"bus";
|
||||
|
||||
phys = <&dsi0_phy>;
|
||||
phy-names = "dsi";
|
||||
|
||||
status = "disabled";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
dsi0_in: endpoint {
|
||||
remote-endpoint = <&dpu_intf1_out>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
dsi0_out: endpoint {
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
dsi0_phy: dsi-phy@ae94400 {
|
||||
compatible = "qcom,dsi-phy-10nm";
|
||||
reg = <0xae94400 0x200>,
|
||||
<0xae94600 0x280>,
|
||||
<0xae94a00 0x1e0>;
|
||||
reg-names = "dsi_phy",
|
||||
"dsi_phy_lane",
|
||||
"dsi_pll";
|
||||
|
||||
#clock-cells = <1>;
|
||||
#phy-cells = <0>;
|
||||
|
||||
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>;
|
||||
clock-names = "iface";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
dsi1: dsi@ae96000 {
|
||||
compatible = "qcom,mdss-dsi-ctrl";
|
||||
reg = <0xae96000 0x400>;
|
||||
reg-names = "dsi_ctrl";
|
||||
|
||||
interrupt-parent = <&mdss>;
|
||||
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_PCLK1_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_ESC1_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_AHB_CLK>,
|
||||
<&dispcc DISP_CC_MDSS_AXI_CLK>;
|
||||
clock-names = "byte",
|
||||
"byte_intf",
|
||||
"pixel",
|
||||
"core",
|
||||
"iface",
|
||||
"bus";
|
||||
|
||||
phys = <&dsi1_phy>;
|
||||
phy-names = "dsi";
|
||||
|
||||
status = "disabled";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
dsi1_in: endpoint {
|
||||
remote-endpoint = <&dpu_intf2_out>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
dsi1_out: endpoint {
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
dsi1_phy: dsi-phy@ae96400 {
|
||||
compatible = "qcom,dsi-phy-10nm";
|
||||
reg = <0xae96400 0x200>,
|
||||
<0xae96600 0x280>,
|
||||
<0xae96a00 0x10e>;
|
||||
reg-names = "dsi_phy",
|
||||
"dsi_phy_lane",
|
||||
"dsi_pll";
|
||||
|
||||
#clock-cells = <1>;
|
||||
#phy-cells = <0>;
|
||||
|
||||
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>;
|
||||
clock-names = "iface";
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
dispcc: clock-controller@af00000 {
|
||||
compatible = "qcom,sdm845-dispcc";
|
||||
reg = <0xaf00000 0x10000>;
|
||||
|
|
@ -1575,6 +1869,78 @@
|
|||
cell-index = <0>;
|
||||
};
|
||||
|
||||
apps_smmu: iommu@15000000 {
|
||||
compatible = "qcom,sdm845-smmu-500", "arm,mmu-500";
|
||||
reg = <0x15000000 0x80000>;
|
||||
#iommu-cells = <2>;
|
||||
#global-interrupts = <1>;
|
||||
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
apss_shared: mailbox@17990000 {
|
||||
compatible = "qcom,sdm845-apss-shared";
|
||||
reg = <0x17990000 0x1000>;
|
||||
|
|
@ -1681,6 +2047,17 @@
|
|||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
cpufreq_hw: cpufreq@17d43000 {
|
||||
compatible = "qcom,cpufreq-hw";
|
||||
reg = <0x17d43000 0x1400>, <0x17d45800 0x1400>;
|
||||
reg-names = "freq-domain0", "freq-domain1";
|
||||
|
||||
clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
|
||||
clock-names = "xo", "alternate";
|
||||
|
||||
#freq-domain-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
thermal-zones {
|
||||
|
|
|
|||
Loading…
Reference in New Issue