hollalinux
/
linux-sg2042
mirror of https://github.com/sophgo/linux-riscv.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

Documentation: networking: Convert stmmac documentation to RST format 

Convert the documentation of the driver to RST format and delete the old
txt and old information that no longer applies.

Also, add some new information.

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Jose Abreu 2020-01-07 11:37:19 +01:00 committed by David S. Miller
parent 1501125460
commit 2ffebffbe7
2 changed files with 697 additions and 401 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

697
Documentation/networking/device_drivers/stmicro/stmmac.rst Normal file
View File

@ -0,0 +1,697 @@
.. SPDX-License-Identifier: GPL-2.0+
==============================================================
Linux Driver for the Synopsys(R) Ethernet Controllers "stmmac"
==============================================================
Authors: Giuseppe Cavallaro <peppe.cavallaro@st.com>,
Alexandre Torgue <alexandre.torgue@st.com>, Jose Abreu <joabreu@synopsys.com>
Contents
========
- In This Release
- Feature List
- Kernel Configuration
- Command Line Parameters
- Driver Information and Notes
- Debug Information
- Support
In This Release
===============
This file describes the stmmac Linux Driver for all the Synopsys(R) Ethernet
Controllers.
Currently, this network device driver is for all STi embedded MAC/GMAC
(i.e. 7xxx/5xxx SoCs), SPEAr (arm), Loongson1B (mips) and XILINX XC2V3000
FF1152AMT0221 D1215994A VIRTEX FPGA board. The Synopsys Ethernet QoS 5.0 IPK
is also supported.
DesignWare(R) Cores Ethernet MAC 10/100/1000 Universal version 3.70a
(and older) and DesignWare(R) Cores Ethernet Quality-of-Service version 4.0
(and upper) have been used for developing this driver as well as
DesignWare(R) Cores XGMAC - 10G Ethernet MAC.
This driver supports both the platform bus and PCI.
This driver includes support for the following Synopsys(R) DesignWare(R)
Cores Ethernet Controllers and corresponding minimum and maximum versions:
+-------------------------------+--------------+--------------+--------------+
| Controller Name | Min. Version | Max. Version | Abbrev. Name |
+===============================+==============+==============+==============+
| Ethernet MAC Universal | N/A | 3.73a | GMAC |
+-------------------------------+--------------+--------------+--------------+
| Ethernet Quality-of-Service | 4.00a | N/A | GMAC4+ |
+-------------------------------+--------------+--------------+--------------+
| XGMAC - 10G Ethernet MAC | 2.10a | N/A | XGMAC2+ |
+-------------------------------+--------------+--------------+--------------+
For questions related to hardware requirements, refer to the documentation
supplied with your Ethernet adapter. All hardware requirements listed apply
to use with Linux.
Feature List
============
The following features are available in this driver:
- GMII/MII/RGMII/SGMII/RMII/XGMII Interface
- Half-Duplex / Full-Duplex Operation
- Energy Efficient Ethernet (EEE)
- IEEE 802.3x PAUSE Packets (Flow Control)
- RMON/MIB Counters
- IEEE 1588 Timestamping (PTP)
- Pulse-Per-Second Output (PPS)
- MDIO Clause 22 / Clause 45 Interface
- MAC Loopback
- ARP Offloading
- Automatic CRC / PAD Insertion and Checking
- Checksum Offload for Received and Transmitted Packets
- Standard or Jumbo Ethernet Packets
- Source Address Insertion / Replacement
- VLAN TAG Insertion / Replacement / Deletion / Filtering (HASH and PERFECT)
- Programmable TX and RX Watchdog and Coalesce Settings
- Destination Address Filtering (PERFECT)
- HASH Filtering (Multicast)
- Layer 3 / Layer 4 Filtering
- Remote Wake-Up Detection
- Receive Side Scaling (RSS)
- Frame Preemption for TX and RX
- Programmable Burst Length, Threshold, Queue Size
- Multiple Queues (up to 8)
- Multiple Scheduling Algorithms (TX: WRR, DWRR, WFQ, SP, CBS, EST, TBS;
RX: WRR, SP)
- Flexible RX Parser
- TCP / UDP Segmentation Offload (TSO, USO)
- Split Header (SPH)
- Safety Features (ECC Protection, Data Parity Protection)
- Selftests using Ethtool
Kernel Configuration
====================
The kernel configuration option is ``CONFIG_STMMAC_ETH``:
- ``CONFIG_STMMAC_PLATFORM``: is to enable the platform driver.
- ``CONFIG_STMMAC_PCI``: is to enable the pci driver.
Command Line Parameters
=======================
If the driver is built as a module the following optional parameters are used
by entering them on the command line with the modprobe command using this
syntax (e.g. for PCI module)::
modprobe stmmac_pci [<option>=<VAL1>,<VAL2>,...]
Driver parameters can be also passed in command line by using::
stmmaceth=watchdog:100,chain_mode=1
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
watchdog
--------
:Valid Range: 5000-None
:Default Value: 5000
This parameter overrides the transmit timeout in milliseconds.
debug
-----
:Valid Range: 0-16 (0=none,...,16=all)
:Default Value: 0
This parameter adjusts the level of debug messages displayed in the system
logs.
phyaddr
-------
:Valid Range: 0-31
:Default Value: -1
This parameter overrides the physical address of the PHY device.
flow_ctrl
---------
:Valid Range: 0-3 (0=off,1=rx,2=tx,3=rx/tx)
:Default Value: 3
This parameter changes the default Flow Control ability.
pause
-----
:Valid Range: 0-65535
:Default Value: 65535
This parameter changes the default Flow Control Pause time.
tc
--
:Valid Range: 64-256
:Default Value: 64
This parameter changes the default HW FIFO Threshold control value.
buf_sz
------
:Valid Range: 1536-16384
:Default Value: 1536
This parameter changes the default RX DMA packet buffer size.
eee_timer
---------
:Valid Range: 0-None
:Default Value: 1000
This parameter changes the default LPI TX Expiration time in milliseconds.
chain_mode
----------
:Valid Range: 0-1 (0=off,1=on)
:Default Value: 0
This parameter changes the default mode of operation from Ring Mode to
Chain Mode.
Driver Information and Notes
============================
Transmit Process
----------------
The xmit method is invoked when the kernel needs to transmit a packet; it sets
the descriptors in the ring and informs the DMA engine that there is a packet
ready to be transmitted.
By default, the driver sets the ``NETIF_F_SG`` bit in the features field of
the ``net_device`` structure, enabling the scatter-gather feature. This is
true on chips and configurations where the checksum can be done in hardware.
Once the controller has finished transmitting the packet, timer will be
scheduled to release the transmit resources.
Receive Process
---------------
When one or more packets are received, an interrupt happens. The interrupts
are not queued, so the driver has to scan all the descriptors in the ring
during the receive process.
This is based on NAPI, so the interrupt handler signals only if there is work
to be done, and it exits. Then the poll method will be scheduled at some
future point.
The incoming packets are stored, by the DMA, in a list of pre-allocated socket
buffers in order to avoid the memcpy (zero-copy).
Interrupt Mitigation
--------------------
The driver is able to mitigate the number of its DMA interrupts using NAPI for
the reception on chips older than the 3.50. New chips have an HW RX Watchdog
used for this mitigation.
Mitigation parameters can be tuned by ethtool.
WoL
---
Wake up on Lan feature through Magic and Unicast frames are supported for the
GMAC, GMAC4/5 and XGMAC core.
DMA Descriptors
---------------
Driver handles both normal and alternate descriptors. The latter has been only
tested on DesignWare(R) Cores Ethernet MAC Universal version 3.41a and later.
stmmac supports DMA descriptor to operate both in dual buffer (RING) and
linked-list(CHAINED) mode. In RING each descriptor points to two data buffer
pointers whereas in CHAINED mode they point to only one data buffer pointer.
RING mode is the default.
In CHAINED mode each descriptor will have pointer to next descriptor in the
list, hence creating the explicit chaining in the descriptor itself, whereas
such explicit chaining is not possible in RING mode.
Extended Descriptors
--------------------
The extended descriptors give us information about the Ethernet payload when
it is carrying PTP packets or TCP/UDP/ICMP over IP. These are not available on
GMAC Synopsys(R) chips older than the 3.50. At probe time the driver will
decide if these can be actually used. This support also is mandatory for PTPv2
because the extra descriptors are used for saving the hardware timestamps and
Extended Status.
Ethtool Support
---------------
Ethtool is supported. For example, driver statistics (including RMON),
internal errors can be taken using::
ethtool -S ethX
Ethtool selftests are also supported. This allows to do some early sanity
checks to the HW using MAC and PHY loopback mechanisms::
ethtool -t ethX
Jumbo and Segmentation Offloading
---------------------------------
Jumbo frames are supported and tested for the GMAC. The GSO has been also
added but it's performed in software. LRO is not supported.
TSO Support
-----------
TSO (TCP Segmentation Offload) feature is supported by GMAC > 4.x and XGMAC
chip family. When a packet is sent through TCP protocol, the TCP stack ensures
that the SKB provided to the low level driver (stmmac in our case) matches
with the maximum frame len (IP header + TCP header + payload <= 1500 bytes
(for MTU set to 1500)). It means that if an application using TCP want to send
a packet which will have a length (after adding headers) > 1514 the packet
will be split in several TCP packets: The data payload is split and headers
(TCP/IP ..) are added. It is done by software.
When TSO is enabled, the TCP stack doesn't care about the maximum frame length
and provide SKB packet to stmmac as it is. The GMAC IP will have to perform
the segmentation by it self to match with maximum frame length.
This feature can be enabled in device tree through ``snps,tso`` entry.
Energy Efficient Ethernet
-------------------------
Energy Efficient Ethernet (EEE) enables IEEE 802.3 MAC sublayer along with a
family of Physical layer to operate in the Low Power Idle (LPI) mode. The EEE
mode supports the IEEE 802.3 MAC operation at 100Mbps, 1000Mbps and 1Gbps.
The LPI mode allows power saving by switching off parts of the communication
device functionality when there is no data to be transmitted & received.
The system on both the side of the link can disable some functionalities and
save power during the period of low-link utilization. The MAC controls whether
the system should enter or exit the LPI mode and communicate this to PHY.
As soon as the interface is opened, the driver verifies if the EEE can be
supported. This is done by looking at both the DMA HW capability register and
the PHY devices MCD registers.
To enter in TX LPI mode the driver needs to have a software timer that enable
and disable the LPI mode when there is nothing to be transmitted.
Precision Time Protocol (PTP)
-----------------------------
The driver supports the IEEE 1588-2002, Precision Time Protocol (PTP), which
enables precise synchronization of clocks in measurement and control systems
implemented with technologies such as network communication.
In addition to the basic timestamp features mentioned in IEEE 1588-2002
Timestamps, new GMAC cores support the advanced timestamp features.
IEEE 1588-2008 can be enabled when configuring the Kernel.
SGMII/RGMII Support
-------------------
New GMAC devices provide own way to manage RGMII/SGMII. This information is
available at run-time by looking at the HW capability register. This means
that the stmmac can manage auto-negotiation and link status w/o using the
PHYLIB stuff. In fact, the HW provides a subset of extended registers to
restart the ANE, verify Full/Half duplex mode and Speed. Thanks to these
registers, it is possible to look at the Auto-negotiated Link Parter Ability.
Physical
--------
The driver is compatible with Physical Abstraction Layer to be connected with
PHY and GPHY devices.
Platform Information
--------------------
Several information can be passed through the platform and device-tree.
::
struct plat_stmmacenet_data {
1) Bus identifier::
int bus_id;
2) PHY Physical Address. If set to -1 the driver will pick the first PHY it
finds::
int phy_addr;
3) PHY Device Interface::
int interface;
4) Specific platform fields for the MDIO bus::
struct stmmac_mdio_bus_data *mdio_bus_data;
5) Internal DMA parameters::
struct stmmac_dma_cfg *dma_cfg;
6) Fixed CSR Clock Range selection::
int clk_csr;
7) HW uses the GMAC core::
int has_gmac;
8) If set the MAC will use Enhanced Descriptors::
int enh_desc;
9) Core is able to perform TX Checksum and/or RX Checksum in HW::
int tx_coe;
int rx_coe;
11) Some HWs are not able to perform the csum in HW for over-sized frames due
to limited buffer sizes. Setting this flag the csum will be done in SW on
JUMBO frames::
int bugged_jumbo;
12) Core has the embedded power module::
int pmt;
13) Force DMA to use the Store and Forward mode or Threshold mode::
int force_sf_dma_mode;
int force_thresh_dma_mode;
15) Force to disable the RX Watchdog feature and switch to NAPI mode::
int riwt_off;
16) Limit the maximum operating speed and MTU::
int max_speed;
int maxmtu;
18) Number of Multicast/Unicast filters::
int multicast_filter_bins;
int unicast_filter_entries;
20) Limit the maximum TX and RX FIFO size::
int tx_fifo_size;
int rx_fifo_size;
21) Use the specified number of TX and RX Queues::
u32 rx_queues_to_use;
u32 tx_queues_to_use;
22) Use the specified TX and RX scheduling algorithm::
u8 rx_sched_algorithm;
u8 tx_sched_algorithm;
23) Internal TX and RX Queue parameters::
struct stmmac_rxq_cfg rx_queues_cfg[MTL_MAX_RX_QUEUES];
struct stmmac_txq_cfg tx_queues_cfg[MTL_MAX_TX_QUEUES];
24) This callback is used for modifying some syscfg registers (on ST SoCs)
according to the link speed negotiated by the physical layer::
void (*fix_mac_speed)(void *priv, unsigned int speed);
25) Callbacks used for calling a custom initialization; This is sometimes
necessary on some platforms (e.g. ST boxes) where the HW needs to have set
some PIO lines or system cfg registers. init/exit callbacks should not use
or modify platform data::
int (*init)(struct platform_device *pdev, void *priv);
void (*exit)(struct platform_device *pdev, void *priv);
26) Perform HW setup of the bus. For example, on some ST platforms this field
is used to configure the AMBA bridge to generate more efficient STBus traffic::
struct mac_device_info *(*setup)(void *priv);
void *bsp_priv;
27) Internal clocks and rates::
struct clk *stmmac_clk;
struct clk *pclk;
struct clk *clk_ptp_ref;
unsigned int clk_ptp_rate;
unsigned int clk_ref_rate;
s32 ptp_max_adj;
28) Main reset::
struct reset_control *stmmac_rst;
29) AXI Internal Parameters::
struct stmmac_axi *axi;
30) HW uses GMAC>4 cores::
int has_gmac4;
31) HW is sun8i based::
bool has_sun8i;
32) Enables TSO feature::
bool tso_en;
33) Enables Receive Side Scaling (RSS) feature::
int rss_en;
34) MAC Port selection::
int mac_port_sel_speed;
35) Enables TX LPI Clock Gating::
bool en_tx_lpi_clockgating;
36) HW uses XGMAC>2.10 cores::
int has_xgmac;
::
}
For MDIO bus data, we have:
::
struct stmmac_mdio_bus_data {
1) PHY mask passed when MDIO bus is registered::
unsigned int phy_mask;
2) List of IRQs, one per PHY::
int *irqs;
3) If IRQs is NULL, use this for probed PHY::
int probed_phy_irq;
4) Set to true if PHY needs reset::
bool needs_reset;
::
}
For DMA engine configuration, we have:
::
struct stmmac_dma_cfg {
1) Programmable Burst Length (TX and RX)::
int pbl;
2) If set, DMA TX / RX will use this value rather than pbl::
int txpbl;
int rxpbl;
3) Enable 8xPBL::
bool pblx8;
4) Enable Fixed or Mixed burst::
int fixed_burst;
int mixed_burst;
5) Enable Address Aligned Beats::
bool aal;
6) Enable Enhanced Addressing (> 32 bits)::
bool eame;
::
}
For DMA AXI parameters, we have:
::
struct stmmac_axi {
1) Enable AXI LPI::
bool axi_lpi_en;
bool axi_xit_frm;
2) Set AXI Write / Read maximum outstanding requests::
u32 axi_wr_osr_lmt;
u32 axi_rd_osr_lmt;
3) Set AXI 4KB bursts::
bool axi_kbbe;
4) Set AXI maximum burst length map::
u32 axi_blen[AXI_BLEN];
5) Set AXI Fixed burst / mixed burst::
bool axi_fb;
bool axi_mb;
6) Set AXI rebuild incrx mode::
bool axi_rb;
::
}
For the RX Queues configuration, we have:
::
struct stmmac_rxq_cfg {
1) Mode to use (DCB or AVB)::
u8 mode_to_use;
2) DMA channel to use::
u32 chan;
3) Packet routing, if applicable::
u8 pkt_route;
4) Use priority routing, and priority to route::
bool use_prio;
u32 prio;
::
}
For the TX Queues configuration, we have:
::
struct stmmac_txq_cfg {
1) Queue weight in scheduler::
u32 weight;
2) Mode to use (DCB or AVB)::
u8 mode_to_use;
3) Credit Base Shaper Parameters::
u32 send_slope;
u32 idle_slope;
u32 high_credit;
u32 low_credit;
4) Use priority scheduling, and priority::
bool use_prio;
u32 prio;
::
}
Device Tree Information
-----------------------
Please refer to the following document:
Documentation/devicetree/bindings/net/snps,dwmac.yaml
HW Capabilities
---------------
Note that, starting from new chips, where it is available the HW capability
register, many configurations are discovered at run-time for example to
understand if EEE, HW csum, PTP, enhanced descriptor etc are actually
available. As strategy adopted in this driver, the information from the HW
capability register can replace what has been passed from the platform.
Debug Information
=================
The driver exports many information i.e. internal statistics, debug
information, MAC and DMA registers etc.
These can be read in several ways depending on the type of the information
actually needed.
For example a user can be use the ethtool support to get statistics: e.g.
using: ``ethtool -S ethX`` (that shows the Management counters (MMC) if
supported) or sees the MAC/DMA registers: e.g. using: ``ethtool -d ethX``
Compiling the Kernel with ``CONFIG_DEBUG_FS`` the driver will export the
following debugfs entries:
- ``descriptors_status``: To show the DMA TX/RX descriptor rings
- ``dma_cap``: To show the HW Capabilities
Developer can also use the ``debug`` module parameter to get further debug
information (please see: NETIF Msg Level).
Support
=======
If an issue is identified with the released source code on a supported kernel
with a supported adapter, email the specific information related to the
issue to netdev@vger.kernel.org

401
Documentation/networking/device_drivers/stmicro/stmmac.txt
View File

@ -1,401 +0,0 @@
STMicroelectronics 10/100/1000 Synopsys Ethernet driver
Copyright (C) 2007-2015 STMicroelectronics Ltd
Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
This is the driver for the MAC 10/100/1000 on-chip Ethernet controllers
(Synopsys IP blocks).
Currently this network device driver is for all STi embedded MAC/GMAC
(i.e. 7xxx/5xxx SoCs), SPEAr (arm), Loongson1B (mips) and XLINX XC2V3000
FF1152AMT0221 D1215994A VIRTEX FPGA board.
DWC Ether MAC 10/100/1000 Universal version 3.70a (and older) and DWC Ether
MAC 10/100 Universal version 4.0 have been used for developing this driver.
This driver supports both the platform bus and PCI.
Please, for more information also visit: www.stlinux.com
1) Kernel Configuration
The kernel configuration option is STMMAC_ETH:
Device Drivers ---> Network device support ---> Ethernet (1000 Mbit) --->
STMicroelectronics 10/100/1000 Ethernet driver (STMMAC_ETH)
CONFIG_STMMAC_PLATFORM: is to enable the platform driver.
CONFIG_STMMAC_PCI: is to enable the pci driver.
2) Driver parameters list:
debug: message level (0: no output, 16: all);
phyaddr: to manually provide the physical address to the PHY device;
buf_sz: DMA buffer size;
tc: control the HW FIFO threshold;
watchdog: transmit timeout (in milliseconds);
flow_ctrl: Flow control ability [on/off];
pause: Flow Control Pause Time;
eee_timer: tx EEE timer;
chain_mode: select chain mode instead of ring.
3) Command line options
Driver parameters can be also passed in command line by using:
stmmaceth=watchdog:100,chain_mode=1
4) Driver information and notes
4.1) Transmit process
The xmit method is invoked when the kernel needs to transmit a packet; it sets
the descriptors in the ring and informs the DMA engine, that there is a packet
ready to be transmitted.
By default, the driver sets the NETIF_F_SG bit in the features field of the
net_device structure, enabling the scatter-gather feature. This is true on
chips and configurations where the checksum can be done in hardware.
Once the controller has finished transmitting the packet, timer will be
scheduled to release the transmit resources.
4.2) Receive process
When one or more packets are received, an interrupt happens. The interrupts
are not queued, so the driver has to scan all the descriptors in the ring during
the receive process.
This is based on NAPI, so the interrupt handler signals only if there is work
to be done, and it exits.
Then the poll method will be scheduled at some future point.
The incoming packets are stored, by the DMA, in a list of pre-allocated socket
buffers in order to avoid the memcpy (zero-copy).
4.3) Interrupt mitigation
The driver is able to mitigate the number of its DMA interrupts
using NAPI for the reception on chips older than the 3.50.
New chips have an HW RX-Watchdog used for this mitigation.
Mitigation parameters can be tuned by ethtool.
4.4) WOL
Wake up on Lan feature through Magic and Unicast frames are supported for the
GMAC core.
4.5) DMA descriptors
Driver handles both normal and alternate descriptors. The latter has been only
tested on DWC Ether MAC 10/100/1000 Universal version 3.41a and later.
STMMAC supports DMA descriptor to operate both in dual buffer (RING)
and linked-list(CHAINED) mode. In RING each descriptor points to two
data buffer pointers whereas in CHAINED mode they point to only one data
buffer pointer. RING mode is the default.
In CHAINED mode each descriptor will have pointer to next descriptor in
the list, hence creating the explicit chaining in the descriptor itself,
whereas such explicit chaining is not possible in RING mode.
4.5.1) Extended descriptors
The extended descriptors give us information about the Ethernet payload
when it is carrying PTP packets or TCP/UDP/ICMP over IP.
These are not available on GMAC Synopsys chips older than the 3.50.
At probe time the driver will decide if these can be actually used.
This support also is mandatory for PTPv2 because the extra descriptors
are used for saving the hardware timestamps and Extended Status.
4.6) Ethtool support
Ethtool is supported.
For example, driver statistics (including RMON), internal errors can be taken
using:
# ethtool -S ethX
command
4.7) Jumbo and Segmentation Offloading
Jumbo frames are supported and tested for the GMAC.
The GSO has been also added but it's performed in software.
LRO is not supported.
4.8) Physical
The driver is compatible with Physical Abstraction Layer to be connected with
PHY and GPHY devices.
4.9) Platform information
Several information can be passed through the platform and device-tree.
struct plat_stmmacenet_data {
char *phy_bus_name;
int bus_id;
int phy_addr;
int interface;
struct stmmac_mdio_bus_data *mdio_bus_data;
struct stmmac_dma_cfg *dma_cfg;
int clk_csr;
int has_gmac;
int enh_desc;
int tx_coe;
int rx_coe;
int bugged_jumbo;
int pmt;
int force_sf_dma_mode;
int force_thresh_dma_mode;
int riwt_off;
int max_speed;
int maxmtu;
void (*fix_mac_speed)(void *priv, unsigned int speed);
void (*bus_setup)(void __iomem *ioaddr);
int (*init)(struct platform_device *pdev, void *priv);
void (*exit)(struct platform_device *pdev, void *priv);
void *bsp_priv;
int has_gmac4;
bool tso_en;
};
Where:
o phy_bus_name: phy bus name to attach to the stmmac.
o bus_id: bus identifier.
o phy_addr: the physical address can be passed from the platform.
If it is set to -1 the driver will automatically
detect it at run-time by probing all the 32 addresses.
o interface: PHY device's interface.
o mdio_bus_data: specific platform fields for the MDIO bus.
o dma_cfg: internal DMA parameters
o pbl: the Programmable Burst Length is maximum number of beats to
be transferred in one DMA transaction.
GMAC also enables the 4xPBL by default. (8xPBL for GMAC 3.50 and newer)
o txpbl/rxpbl: GMAC and newer supports independent DMA pbl for tx/rx.
o pblx8: Enable 8xPBL (4xPBL for core rev < 3.50). Enabled by default.
o fixed_burst/mixed_burst/aal
o clk_csr: fixed CSR Clock range selection.
o has_gmac: uses the GMAC core.
o enh_desc: if sets the MAC will use the enhanced descriptor structure.
o tx_coe: core is able to perform the tx csum in HW.
o rx_coe: the supports three check sum offloading engine types:
type_1, type_2 (full csum) and no RX coe.
o bugged_jumbo: some HWs are not able to perform the csum in HW for
over-sized frames due to limited buffer sizes.
Setting this flag the csum will be done in SW on
JUMBO frames.
o pmt: core has the embedded power module (optional).
o force_sf_dma_mode: force DMA to use the Store and Forward mode
instead of the Threshold.
o force_thresh_dma_mode: force DMA to use the Threshold mode other than
the Store and Forward mode.
o riwt_off: force to disable the RX watchdog feature and switch to NAPI mode.
o fix_mac_speed: this callback is used for modifying some syscfg registers
(on ST SoCs) according to the link speed negotiated by the
physical layer .
o bus_setup: perform HW setup of the bus. For example, on some ST platforms
this field is used to configure the AMBA bridge to generate more
efficient STBus traffic.
o init/exit: callbacks used for calling a custom initialization;
this is sometime necessary on some platforms (e.g. ST boxes)
where the HW needs to have set some PIO lines or system cfg
registers. init/exit callbacks should not use or modify
platform data.
o bsp_priv: another private pointer.
o has_gmac4: uses GMAC4 core.
o tso_en: Enables TSO (TCP Segmentation Offload) feature.
For MDIO bus The we have:
struct stmmac_mdio_bus_data {
int (*phy_reset)(void *priv);
unsigned int phy_mask;
int *irqs;
int probed_phy_irq;
};
Where:
o phy_reset: hook to reset the phy device attached to the bus.
o phy_mask: phy mask passed when register the MDIO bus within the driver.
o irqs: list of IRQs, one per PHY.
o probed_phy_irq: if irqs is NULL, use this for probed PHY.
For DMA engine we have the following internal fields that should be
tuned according to the HW capabilities.
struct stmmac_dma_cfg {
int pbl;
int txpbl;
int rxpbl;
bool pblx8;
int fixed_burst;
int mixed_burst;
bool aal;
};
Where:
o pbl: Programmable Burst Length (tx and rx)
o txpbl: Transmit Programmable Burst Length. Only for GMAC and newer.
If set, DMA tx will use this value rather than pbl.
o rxpbl: Receive Programmable Burst Length. Only for GMAC and newer.
If set, DMA rx will use this value rather than pbl.
o pblx8: Enable 8xPBL (4xPBL for core rev < 3.50). Enabled by default.
o fixed_burst: program the DMA to use the fixed burst mode
o mixed_burst: program the DMA to use the mixed burst mode
o aal: Address-Aligned Beats
---
Below an example how the structures above are using on ST platforms.
static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = {
.has_gmac = 0,
.enh_desc = 0,
.fix_mac_speed = stxYYY_ethernet_fix_mac_speed,
|
|-> to write an internal syscfg
| on this platform when the
| link speed changes from 10 to
| 100 and viceversa
.init = &stmmac_claim_resource,
|
|-> On ST SoC this calls own "PAD"
| manager framework to claim
| all the resources necessary
| (GPIO ...). The .custom_cfg field
| is used to pass a custom config.
};
Below the usage of the stmmac_mdio_bus_data: on this SoC, in fact,
there are two MAC cores: one MAC is for MDIO Bus/PHY emulation
with fixed_link support.
static struct stmmac_mdio_bus_data stmmac1_mdio_bus = {
.phy_reset = phy_reset;
|
|-> function to provide the phy_reset on this board
.phy_mask = 0,
};
static struct fixed_phy_status stmmac0_fixed_phy_status = {
.link = 1,
.speed = 100,
.duplex = 1,
};
During the board's device_init we can configure the first
MAC for fixed_link by calling:
fixed_phy_add(PHY_POLL, 1, &stmmac0_fixed_phy_status);
and the second one, with a real PHY device attached to the bus,
by using the stmmac_mdio_bus_data structure (to provide the id, the
reset procedure etc).
Note that, starting from new chips, where it is available the HW capability
register, many configurations are discovered at run-time for example to
understand if EEE, HW csum, PTP, enhanced descriptor etc are actually
available. As strategy adopted in this driver, the information from the HW
capability register can replace what has been passed from the platform.
4.10) Device-tree support.
Please see the following document:
Documentation/devicetree/bindings/net/stmmac.txt
4.11) This is a summary of the content of some relevant files:
o stmmac_main.c: implements the main network device driver;
o stmmac_mdio.c: provides MDIO functions;
o stmmac_pci: this is the PCI driver;
o stmmac_platform.c: this the platform driver (OF supported);
o stmmac_ethtool.c: implements the ethtool support;
o stmmac.h: private driver structure;
o common.h: common definitions and VFTs;
o mmc_core.c/mmc.h: Management MAC Counters;
o stmmac_hwtstamp.c: HW timestamp support for PTP;
o stmmac_ptp.c: PTP 1588 clock;
o stmmac_pcs.h: Physical Coding Sublayer common implementation;
o dwmac-<XXX>.c: these are for the platform glue-logic file; e.g. dwmac-sti.c
for STMicroelectronics SoCs.
- GMAC 3.x
o descs.h: descriptor structure definitions;
o dwmac1000_core.c: dwmac GiGa core functions;
o dwmac1000_dma.c: dma functions for the GMAC chip;
o dwmac1000.h: specific header file for the dwmac GiGa;
o dwmac100_core: dwmac 100 core code;
o dwmac100_dma.c: dma functions for the dwmac 100 chip;
o dwmac1000.h: specific header file for the MAC;
o dwmac_lib.c: generic DMA functions;
o enh_desc.c: functions for handling enhanced descriptors;
o norm_desc.c: functions for handling normal descriptors;
o chain_mode.c/ring_mode.c:: functions to manage RING/CHAINED modes;
- GMAC4.x generation
o dwmac4_core.c: dwmac GMAC4.x core functions;
o dwmac4_desc.c: functions for handling GMAC4.x descriptors;
o dwmac4_descs.h: descriptor definitions;
o dwmac4_dma.c: dma functions for the GMAC4.x chip;
o dwmac4_dma.h: dma definitions for the GMAC4.x chip;
o dwmac4.h: core definitions for the GMAC4.x chip;
o dwmac4_lib.c: generic GMAC4.x functions;
4.12) TSO support (GMAC4.x)
TSO (Tcp Segmentation Offload) feature is supported by GMAC 4.x chip family.
When a packet is sent through TCP protocol, the TCP stack ensures that
the SKB provided to the low level driver (stmmac in our case) matches with
the maximum frame len (IP header + TCP header + payload <= 1500 bytes (for
MTU set to 1500)). It means that if an application using TCP want to send a
packet which will have a length (after adding headers) > 1514 the packet
will be split in several TCP packets: The data payload is split and headers
(TCP/IP ..) are added. It is done by software.
When TSO is enabled, the TCP stack doesn't care about the maximum frame
length and provide SKB packet to stmmac as it is. The GMAC IP will have to
perform the segmentation by it self to match with maximum frame length.
This feature can be enabled in device tree through "snps,tso" entry.
5) Debug Information
The driver exports many information i.e. internal statistics,
debug information, MAC and DMA registers etc.
These can be read in several ways depending on the
type of the information actually needed.
For example a user can be use the ethtool support
to get statistics: e.g. using: ethtool -S ethX
(that shows the Management counters (MMC) if supported)
or sees the MAC/DMA registers: e.g. using: ethtool -d ethX
Compiling the Kernel with CONFIG_DEBUG_FS the driver will export the following
debugfs entries:
/sys/kernel/debug/stmmaceth/descriptors_status
To show the DMA TX/RX descriptor rings
Developer can also use the "debug" module parameter to get further debug
information (please see: NETIF Msg Level).
6) Energy Efficient Ethernet
Energy Efficient Ethernet(EEE) enables IEEE 802.3 MAC sublayer along
with a family of Physical layer to operate in the Low power Idle(LPI)
mode. The EEE mode supports the IEEE 802.3 MAC operation at 100Mbps,
1000Mbps & 10Gbps.
The LPI mode allows power saving by switching off parts of the
communication device functionality when there is no data to be
transmitted & received. The system on both the side of the link can
disable some functionalities & save power during the period of low-link
utilization. The MAC controls whether the system should enter or exit
the LPI mode & communicate this to PHY.
As soon as the interface is opened, the driver verifies if the EEE can
be supported. This is done by looking at both the DMA HW capability
register and the PHY devices MCD registers.
To enter in Tx LPI mode the driver needs to have a software timer
that enable and disable the LPI mode when there is nothing to be
transmitted.
7) Precision Time Protocol (PTP)
The driver supports the IEEE 1588-2002, Precision Time Protocol (PTP),
which enables precise synchronization of clocks in measurement and
control systems implemented with technologies such as network
communication.
In addition to the basic timestamp features mentioned in IEEE 1588-2002
Timestamps, new GMAC cores support the advanced timestamp features.
IEEE 1588-2008 that can be enabled when configure the Kernel.
8) SGMII/RGMII support
New GMAC devices provide own way to manage RGMII/SGMII.
This information is available at run-time by looking at the
HW capability register. This means that the stmmac can manage
auto-negotiation and link status w/o using the PHYLIB stuff.
In fact, the HW provides a subset of extended registers to
restart the ANE, verify Full/Half duplex mode and Speed.
Thanks to these registers, it is possible to look at the
Auto-negotiated Link Parter Ability.