powerpc/85xx: Add P1010RDB board support

P1010RDB Overview
 -----------------
 1Gbyte DDR3 (on board DDR)
 32Mbyte 16bit NOR flash
 32Mbyte SLC NAND Flash
 256 Kbit M24256 I2C EEPROM
 128 Mbit SPI Flash memory
 I2C Board 128x8 bit memory
 SD/MMC connector to interface with the SD memory card
 2 SATA interface
         1 internal SATA connect to 2.5. 160G SATA2 HDD
         1 eSATA connector to rear panel
 USB 2.0
         x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
         x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
 eTSEC1: Connected to RGMII PHY VSC8641XKO
 eTSEC2: Connected to SGMII PHY VSC8221
 eTSEC3: Connected to SGMII PHY VSC8221 eCAN
 Two DB-9 female connectors for Field bus interface UART
 DUART interface: supports two UARTs up to 115200 bps for console display

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This commit is contained in:
Prabhakar Kushwaha 2011-06-02 20:28:08 +00:00 committed by Kumar Gala
parent 2e5460f31a
commit 2d05c392b8
6 changed files with 790 additions and 0 deletions

View File

@ -0,0 +1,280 @@
/*
* P1010 RDB Device Tree Source
*
* Copyright 2011 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
/include/ "p1010si.dtsi"
/ {
model = "fsl,P1010RDB";
compatible = "fsl,P1010RDB";
aliases {
serial0 = &serial0;
serial1 = &serial1;
ethernet0 = &enet0;
ethernet1 = &enet1;
ethernet2 = &enet2;
pci0 = &pci0;
pci1 = &pci1;
};
memory {
device_type = "memory";
};
ifc@ffe1e000 {
/* NOR, NAND Flashes and CPLD on board */
ranges = <0x0 0x0 0x0 0xee000000 0x02000000
0x1 0x0 0x0 0xff800000 0x00010000
0x3 0x0 0x0 0xffb00000 0x00000020>;
nor@0,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x0 0x0 0x2000000>;
bank-width = <2>;
device-width = <1>;
partition@40000 {
/* 256KB for DTB Image */
reg = <0x00040000 0x00040000>;
label = "NOR DTB Image";
};
partition@80000 {
/* 7 MB for Linux Kernel Image */
reg = <0x00080000 0x00700000>;
label = "NOR Linux Kernel Image";
};
partition@800000 {
/* 20MB for JFFS2 based Root file System */
reg = <0x00800000 0x01400000>;
label = "NOR JFFS2 Root File System";
};
partition@1f00000 {
/* This location must not be altered */
/* 512KB for u-boot Bootloader Image */
/* 512KB for u-boot Environment Variables */
reg = <0x01f00000 0x00100000>;
label = "NOR U-Boot Image";
read-only;
};
};
nand@1,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,ifc-nand";
reg = <0x1 0x0 0x10000>;
partition@0 {
/* This location must not be altered */
/* 1MB for u-boot Bootloader Image */
reg = <0x0 0x00100000>;
label = "NAND U-Boot Image";
read-only;
};
partition@100000 {
/* 1MB for DTB Image */
reg = <0x00100000 0x00100000>;
label = "NAND DTB Image";
};
partition@200000 {
/* 4MB for Linux Kernel Image */
reg = <0x00200000 0x00400000>;
label = "NAND Linux Kernel Image";
};
partition@600000 {
/* 4MB for Compressed Root file System Image */
reg = <0x00600000 0x00400000>;
label = "NAND Compressed RFS Image";
};
partition@a00000 {
/* 15MB for JFFS2 based Root file System */
reg = <0x00a00000 0x00f00000>;
label = "NAND JFFS2 Root File System";
};
partition@1900000 {
/* 7MB for User Area */
reg = <0x01900000 0x00700000>;
label = "NAND User area";
};
};
cpld@3,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,p1010rdb-cpld";
reg = <0x3 0x0 0x0000020>;
bank-width = <1>;
device-width = <1>;
};
};
soc@ffe00000 {
spi@7000 {
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spansion,s25sl12801";
reg = <0>;
spi-max-frequency = <50000000>;
partition@0 {
/* 1MB for u-boot Bootloader Image */
/* 1MB for Environment */
reg = <0x0 0x00100000>;
label = "SPI Flash U-Boot Image";
read-only;
};
partition@100000 {
/* 512KB for DTB Image */
reg = <0x00100000 0x00080000>;
label = "SPI Flash DTB Image";
};
partition@180000 {
/* 4MB for Linux Kernel Image */
reg = <0x00180000 0x00400000>;
label = "SPI Flash Linux Kernel Image";
};
partition@580000 {
/* 4MB for Compressed RFS Image */
reg = <0x00580000 0x00400000>;
label = "SPI Flash Compressed RFSImage";
};
partition@980000 {
/* 6.5MB for JFFS2 based RFS */
reg = <0x00980000 0x00680000>;
label = "SPI Flash JFFS2 RFS";
};
};
};
can0@1c000 {
fsl,flexcan-clock-source = "platform";
};
can1@1d000 {
fsl,flexcan-clock-source = "platform";
};
usb@22000 {
phy_type = "utmi";
};
mdio@24000 {
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <3 1>;
reg = <0x1>;
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
reg = <0x0>;
};
phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
reg = <0x2>;
};
};
enet0: ethernet@b0000 {
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
};
enet1: ethernet@b1000 {
phy-handle = <&phy1>;
tbi-handle = <&tbi0>;
phy-connection-type = "sgmii";
};
enet2: ethernet@b2000 {
phy-handle = <&phy2>;
tbi-handle = <&tbi1>;
phy-connection-type = "sgmii";
};
};
pci0: pcie@ffe09000 {
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
pcie@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
interrupt-parent = <&mpic>;
interrupts = <16 2>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 */
0000 0x0 0x0 0x1 &mpic 0x4 0x1
0000 0x0 0x0 0x2 &mpic 0x5 0x1
0000 0x0 0x0 0x3 &mpic 0x6 0x1
0000 0x0 0x0 0x4 &mpic 0x7 0x1
>;
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
pci1: pcie@ffe0a000 {
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
pcie@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
interrupt-parent = <&mpic>;
interrupts = <16 2>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x0 */
0000 0x0 0x0 0x1 &mpic 0x4 0x1
0000 0x0 0x0 0x2 &mpic 0x5 0x1
0000 0x0 0x0 0x3 &mpic 0x6 0x1
0000 0x0 0x0 0x4 &mpic 0x7 0x1
>;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
};

View File

@ -0,0 +1,376 @@
/*
* P1010si Device Tree Source
*
* Copyright 2011 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
/dts-v1/;
/ {
compatible = "fsl,P1010";
#address-cells = <2>;
#size-cells = <2>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
PowerPC,P1010@0 {
device_type = "cpu";
reg = <0x0>;
next-level-cache = <&L2>;
};
};
ifc@ffe1e000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,ifc", "simple-bus";
reg = <0x0 0xffe1e000 0 0x2000>;
interrupts = <16 2 19 2>;
interrupt-parent = <&mpic>;
};
soc@ffe00000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
compatible = "fsl,p1010-immr", "simple-bus";
ranges = <0x0 0x0 0xffe00000 0x100000>;
bus-frequency = <0>; // Filled out by uboot.
ecm-law@0 {
compatible = "fsl,ecm-law";
reg = <0x0 0x1000>;
fsl,num-laws = <12>;
};
ecm@1000 {
compatible = "fsl,p1010-ecm", "fsl,ecm";
reg = <0x1000 0x1000>;
interrupts = <16 2>;
interrupt-parent = <&mpic>;
};
memory-controller@2000 {
compatible = "fsl,p1010-memory-controller";
reg = <0x2000 0x1000>;
interrupt-parent = <&mpic>;
interrupts = <16 2>;
};
i2c@3000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
reg = <0x3000 0x100>;
interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
i2c@3100 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <1>;
compatible = "fsl-i2c";
reg = <0x3100 0x100>;
interrupts = <43 2>;
interrupt-parent = <&mpic>;
dfsrr;
};
serial0: serial@4500 {
cell-index = <0>;
device_type = "serial";
compatible = "ns16550";
reg = <0x4500 0x100>;
clock-frequency = <0>;
interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
serial1: serial@4600 {
cell-index = <1>;
device_type = "serial";
compatible = "ns16550";
reg = <0x4600 0x100>;
clock-frequency = <0>;
interrupts = <42 2>;
interrupt-parent = <&mpic>;
};
spi@7000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc8536-espi";
reg = <0x7000 0x1000>;
interrupts = <59 0x2>;
interrupt-parent = <&mpic>;
fsl,espi-num-chipselects = <1>;
};
gpio: gpio-controller@f000 {
#gpio-cells = <2>;
compatible = "fsl,mpc8572-gpio";
reg = <0xf000 0x100>;
interrupts = <47 0x2>;
interrupt-parent = <&mpic>;
gpio-controller;
};
sata@18000 {
compatible = "fsl,pq-sata-v2";
reg = <0x18000 0x1000>;
cell-index = <1>;
interrupts = <74 0x2>;
interrupt-parent = <&mpic>;
};
sata@19000 {
compatible = "fsl,pq-sata-v2";
reg = <0x19000 0x1000>;
cell-index = <2>;
interrupts = <41 0x2>;
interrupt-parent = <&mpic>;
};
can0@1c000 {
compatible = "fsl,flexcan-v1.0";
reg = <0x1c000 0x1000>;
interrupts = <48 0x2>;
interrupt-parent = <&mpic>;
fsl,flexcan-clock-divider = <2>;
};
can1@1d000 {
compatible = "fsl,flexcan-v1.0";
reg = <0x1d000 0x1000>;
interrupts = <61 0x2>;
interrupt-parent = <&mpic>;
fsl,flexcan-clock-divider = <2>;
};
L2: l2-cache-controller@20000 {
compatible = "fsl,p1010-l2-cache-controller",
"fsl,p1014-l2-cache-controller";
reg = <0x20000 0x1000>;
cache-line-size = <32>; // 32 bytes
cache-size = <0x40000>; // L2,256K
interrupt-parent = <&mpic>;
interrupts = <16 2>;
};
dma@21300 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,p1010-dma", "fsl,eloplus-dma";
reg = <0x21300 0x4>;
ranges = <0x0 0x21100 0x200>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
reg = <0x0 0x80>;
cell-index = <0>;
interrupt-parent = <&mpic>;
interrupts = <20 2>;
};
dma-channel@80 {
compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
reg = <0x80 0x80>;
cell-index = <1>;
interrupt-parent = <&mpic>;
interrupts = <21 2>;
};
dma-channel@100 {
compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
reg = <0x100 0x80>;
cell-index = <2>;
interrupt-parent = <&mpic>;
interrupts = <22 2>;
};
dma-channel@180 {
compatible = "fsl,p1010-dma-channel", "fsl,eloplus-dma-channel";
reg = <0x180 0x80>;
cell-index = <3>;
interrupt-parent = <&mpic>;
interrupts = <23 2>;
};
};
usb@22000 {
compatible = "fsl-usb2-dr";
reg = <0x22000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&mpic>;
interrupts = <28 0x2>;
dr_mode = "host";
};
mdio@24000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,etsec2-mdio";
reg = <0x24000 0x1000 0xb0030 0x4>;
};
mdio@25000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,etsec2-tbi";
reg = <0x25000 0x1000 0xb1030 0x4>;
tbi0: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@26000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,etsec2-tbi";
reg = <0x26000 0x1000 0xb1030 0x4>;
tbi1: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
sdhci@2e000 {
compatible = "fsl,esdhc";
reg = <0x2e000 0x1000>;
interrupts = <72 0x8>;
interrupt-parent = <&mpic>;
/* Filled in by U-Boot */
clock-frequency = <0>;
fsl,sdhci-auto-cmd12;
};
enet0: ethernet@b0000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupt-parent = <&mpic>;
queue-group@0 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xb0000 0x1000>;
fsl,rx-bit-map = <0xff>;
fsl,tx-bit-map = <0xff>;
interrupts = <29 2 30 2 34 2>;
};
};
enet1: ethernet@b1000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupt-parent = <&mpic>;
queue-group@0 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xb1000 0x1000>;
fsl,rx-bit-map = <0xff>;
fsl,tx-bit-map = <0xff>;
interrupts = <35 2 36 2 40 2>;
};
};
enet2: ethernet@b2000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupt-parent = <&mpic>;
queue-group@0 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xb2000 0x1000>;
fsl,rx-bit-map = <0xff>;
fsl,tx-bit-map = <0xff>;
interrupts = <31 2 32 2 33 2>;
};
};
mpic: pic@40000 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
};
msi@41600 {
compatible = "fsl,p1010-msi", "fsl,mpic-msi";
reg = <0x41600 0x80>;
msi-available-ranges = <0 0x100>;
interrupts = <
0xe0 0
0xe1 0
0xe2 0
0xe3 0
0xe4 0
0xe5 0
0xe6 0
0xe7 0>;
interrupt-parent = <&mpic>;
};
global-utilities@e0000 { //global utilities block
compatible = "fsl,p1010-guts";
reg = <0xe0000 0x1000>;
fsl,has-rstcr;
};
};
pci0: pcie@ffe09000 {
compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
device_type = "pci";
#size-cells = <2>;
#address-cells = <3>;
reg = <0 0xffe09000 0 0x1000>;
bus-range = <0 255>;
clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
interrupts = <16 2>;
};
pci1: pcie@ffe0a000 {
compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
device_type = "pci";
#size-cells = <2>;
#address-cells = <3>;
reg = <0 0xffe0a000 0 0x1000>;
bus-range = <0 255>;
clock-frequency = <33333333>;
interrupt-parent = <&mpic>;
interrupts = <16 2>;
};
};

View File

@ -26,6 +26,7 @@ CONFIG_MPC85xx_MDS=y
CONFIG_MPC8536_DS=y
CONFIG_MPC85xx_DS=y
CONFIG_MPC85xx_RDB=y
CONFIG_P1010_RDB=y
CONFIG_P1022_DS=y
CONFIG_P1023_RDS=y
CONFIG_SOCRATES=y

View File

@ -67,6 +67,16 @@ config MPC85xx_RDB
help
This option enables support for the MPC85xx RDB (P2020 RDB) board
config P1010_RDB
bool "Freescale P1010RDB"
select DEFAULT_UIMAGE
help
This option enables support for the MPC85xx RDB (P1010 RDB) board
P1010RDB contains P1010Si, which provides CPU performance up to 800
MHz and 1600 DMIPS, additional functionality and faster interfaces
(DDR3/3L, SATA II, and PCI Express).
config P1022_DS
bool "Freescale P1022 DS"
select DEFAULT_UIMAGE

View File

@ -10,6 +10,7 @@ obj-$(CONFIG_MPC8536_DS) += mpc8536_ds.o
obj-$(CONFIG_MPC85xx_DS) += mpc85xx_ds.o
obj-$(CONFIG_MPC85xx_MDS) += mpc85xx_mds.o
obj-$(CONFIG_MPC85xx_RDB) += mpc85xx_rdb.o
obj-$(CONFIG_P1010_RDB) += p1010rdb.o
obj-$(CONFIG_P1022_DS) += p1022_ds.o
obj-$(CONFIG_P1023_RDS) += p1023_rds.o
obj-$(CONFIG_P3041_DS) += p3041_ds.o corenet_ds.o

View File

@ -0,0 +1,122 @@
/*
* P1010RDB Board Setup
*
* Copyright 2011 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/of_platform.h>
#include <asm/system.h>
#include <asm/time.h>
#include <asm/machdep.h>
#include <asm/pci-bridge.h>
#include <mm/mmu_decl.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/mpic.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
void __init p1010_rdb_pic_init(void)
{
struct mpic *mpic;
struct resource r;
struct device_node *np;
np = of_find_node_by_type(NULL, "open-pic");
if (np == NULL) {
printk(KERN_ERR "Could not find open-pic node\n");
return;
}
if (of_address_to_resource(np, 0, &r)) {
printk(KERN_ERR "Failed to map mpic register space\n");
of_node_put(np);
return;
}
mpic = mpic_alloc(np, r.start, MPIC_PRIMARY | MPIC_WANTS_RESET |
MPIC_BIG_ENDIAN | MPIC_BROKEN_FRR_NIRQS | MPIC_SINGLE_DEST_CPU,
0, 256, " OpenPIC ");
BUG_ON(mpic == NULL);
of_node_put(np);
mpic_init(mpic);
}
/*
* Setup the architecture
*/
static void __init p1010_rdb_setup_arch(void)
{
#ifdef CONFIG_PCI
struct device_node *np;
#endif
if (ppc_md.progress)
ppc_md.progress("p1010_rdb_setup_arch()", 0);
#ifdef CONFIG_PCI
for_each_node_by_type(np, "pci") {
if (of_device_is_compatible(np, "fsl,p1010-pcie"))
fsl_add_bridge(np, 0);
}
#endif
printk(KERN_INFO "P1010 RDB board from Freescale Semiconductor\n");
}
static struct of_device_id __initdata p1010rdb_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
{},
};
static int __init p1010rdb_publish_devices(void)
{
return of_platform_bus_probe(NULL, p1010rdb_ids, NULL);
}
machine_device_initcall(p1010_rdb, p1010rdb_publish_devices);
machine_arch_initcall(p1010_rdb, swiotlb_setup_bus_notifier);
/*
* Called very early, device-tree isn't unflattened
*/
static int __init p1010_rdb_probe(void)
{
unsigned long root = of_get_flat_dt_root();
if (of_flat_dt_is_compatible(root, "fsl,P1010RDB"))
return 1;
return 0;
}
define_machine(p1010_rdb) {
.name = "P1010 RDB",
.probe = p1010_rdb_probe,
.setup_arch = p1010_rdb_setup_arch,
.init_IRQ = p1010_rdb_pic_init,
#ifdef CONFIG_PCI
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
#endif
.get_irq = mpic_get_irq,
.restart = fsl_rstcr_restart,
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
};