sata_mv: use new sata phy register settings for new devices

Marvell's new SoC (65 nano) needs different settings for its SATA
PHY registers.

Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit is contained in:
Martin Michlmayr 2009-05-04 20:58:50 +02:00 committed by Jeff Garzik
parent 842faa6c1a
commit 29b7e43c31
1 changed files with 67 additions and 2 deletions

View File

@ -293,6 +293,10 @@ enum {
FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */
FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */
PHY_MODE9_GEN2 = 0x398,
PHY_MODE9_GEN1 = 0x39c,
PHYCFG_OFS = 0x3a0, /* only in 65n devices */
MV5_PHY_MODE = 0x74,
MV5_LTMODE = 0x30,
MV5_PHY_CTL = 0x0C,
@ -609,6 +613,8 @@ static int mv_soc_reset_hc(struct mv_host_priv *hpriv,
static void mv_soc_reset_flash(struct mv_host_priv *hpriv,
void __iomem *mmio);
static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio);
static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv,
void __iomem *mmio, unsigned int port);
static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio);
static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
@ -807,6 +813,14 @@ static const struct mv_hw_ops mv_soc_ops = {
.reset_bus = mv_soc_reset_bus,
};
static const struct mv_hw_ops mv_soc_65n_ops = {
.phy_errata = mv_soc_65n_phy_errata,
.enable_leds = mv_soc_enable_leds,
.reset_hc = mv_soc_reset_hc,
.reset_flash = mv_soc_reset_flash,
.reset_bus = mv_soc_reset_bus,
};
/*
* Functions
*/
@ -3397,6 +3411,53 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
return;
}
static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv,
void __iomem *mmio, unsigned int port)
{
void __iomem *port_mmio = mv_port_base(mmio, port);
u32 reg;
reg = readl(port_mmio + PHY_MODE3);
reg &= ~(0x3 << 27); /* SELMUPF (bits 28:27) to 1 */
reg |= (0x1 << 27);
reg &= ~(0x3 << 29); /* SELMUPI (bits 30:29) to 1 */
reg |= (0x1 << 29);
writel(reg, port_mmio + PHY_MODE3);
reg = readl(port_mmio + PHY_MODE4);
reg &= ~0x1; /* SATU_OD8 (bit 0) to 0, reserved bit 16 must be set */
reg |= (0x1 << 16);
writel(reg, port_mmio + PHY_MODE4);
reg = readl(port_mmio + PHY_MODE9_GEN2);
reg &= ~0xf; /* TXAMP[3:0] (bits 3:0) to 8 */
reg |= 0x8;
reg &= ~(0x1 << 14); /* TXAMP[4] (bit 14) to 0 */
writel(reg, port_mmio + PHY_MODE9_GEN2);
reg = readl(port_mmio + PHY_MODE9_GEN1);
reg &= ~0xf; /* TXAMP[3:0] (bits 3:0) to 8 */
reg |= 0x8;
reg &= ~(0x1 << 14); /* TXAMP[4] (bit 14) to 0 */
writel(reg, port_mmio + PHY_MODE9_GEN1);
}
/**
* soc_is_65 - check if the soc is 65 nano device
*
* Detect the type of the SoC, this is done by reading the PHYCFG_OFS
* register, this register should contain non-zero value and it exists only
* in the 65 nano devices, when reading it from older devices we get 0.
*/
static bool soc_is_65n(struct mv_host_priv *hpriv)
{
void __iomem *port0_mmio = mv_port_base(hpriv->base, 0);
if (readl(port0_mmio + PHYCFG_OFS))
return true;
return false;
}
static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i)
{
u32 ifcfg = readl(port_mmio + SATA_IFCFG);
@ -3737,6 +3798,9 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
}
break;
case chip_soc:
if (soc_is_65n(hpriv))
hpriv->ops = &mv_soc_65n_ops;
else
hpriv->ops = &mv_soc_ops;
hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE |
MV_HP_ERRATA_60X1C0;
@ -3800,6 +3864,7 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
n_hc = mv_get_hc_count(host->ports[0]->flags);
for (port = 0; port < host->n_ports; port++)
if (hpriv->ops->read_preamp)
hpriv->ops->read_preamp(hpriv, port, mmio);
rc = hpriv->ops->reset_hc(hpriv, mmio, n_hc);