MAX8952 PMIC Driver Initial Release
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV with DVS support. In this initial release, users can set voltages for four DVS modes, RAMP delay values, and SYNC frequency. Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID is not supported in this release. If GPIO of EN is not valid in platform data, the driver assumes that it is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down VID0 and VID1 to fix DVS mode as 0 and disables DVS support. We assume that V_OUT is capable to provide every voltage from 770mV to 1.40V in 10mV steps although the data sheet has some ambiguity on it. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> -- v2: - Style correction - Can accept platform_data with invalid GPIOs - Removed unnecessary features - Improved error handling Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This commit is contained in:
MyungJoo Ham
Liam Girdwood
parent
2d3b07c07b
commit
202f4f53e5
|
|
@ -100,6 +100,14 @@ config REGULATOR_MAX8925
|
|||
help
|
||||
Say y here to support the voltage regulaltor of Maxim MAX8925 PMIC.
|
||||
|
||||
config REGULATOR_MAX8952
|
||||
tristate "Maxim MAX8952 Power Management IC"
|
||||
depends on I2C
|
||||
help
|
||||
This driver controls a Maxim 8952 voltage output regulator
|
||||
via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS
|
||||
modes ranging from 0.77V to 1.40V by 0.01V steps.
|
||||
|
||||
config REGULATOR_MAX8998
|
||||
tristate "Maxim 8998 voltage regulator"
|
||||
depends on MFD_MAX8998
|
||||
|
|
|
|||
|
|
@ -17,6 +17,7 @@ obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o
|
|||
obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o
|
||||
obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
|
||||
obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
|
||||
obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
|
||||
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
|
||||
obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,360 @@
|
|||
/*
|
||||
* max8952.c - Voltage and current regulation for the Maxim 8952
|
||||
*
|
||||
* Copyright (C) 2010 Samsung Electronics
|
||||
* MyungJoo Ham <myungjoo.ham@samsung.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
||||
*/
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/err.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/regulator/driver.h>
|
||||
#include <linux/regulator/max8952.h>
|
||||
#include <linux/mutex.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/io.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
/* Registers */
|
||||
enum {
|
||||
MAX8952_REG_MODE0,
|
||||
MAX8952_REG_MODE1,
|
||||
MAX8952_REG_MODE2,
|
||||
MAX8952_REG_MODE3,
|
||||
MAX8952_REG_CONTROL,
|
||||
MAX8952_REG_SYNC,
|
||||
MAX8952_REG_RAMP,
|
||||
MAX8952_REG_CHIP_ID1,
|
||||
MAX8952_REG_CHIP_ID2,
|
||||
};
|
||||
|
||||
struct max8952_data {
|
||||
struct i2c_client *client;
|
||||
struct device *dev;
|
||||
struct mutex mutex;
|
||||
struct max8952_platform_data *pdata;
|
||||
struct regulator_dev *rdev;
|
||||
|
||||
bool vid0;
|
||||
bool vid1;
|
||||
bool en;
|
||||
};
|
||||
|
||||
static int max8952_read_reg(struct max8952_data *max8952, u8 reg)
|
||||
{
|
||||
int ret = i2c_smbus_read_byte_data(max8952->client, reg);
|
||||
if (ret > 0)
|
||||
ret &= 0xff;
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int max8952_write_reg(struct max8952_data *max8952,
|
||||
u8 reg, u8 value)
|
||||
{
|
||||
return i2c_smbus_write_byte_data(max8952->client, reg, value);
|
||||
}
|
||||
|
||||
static int max8952_voltage(struct max8952_data *max8952, u8 mode)
|
||||
{
|
||||
return (max8952->pdata->dvs_mode[mode] * 10 + 770) * 1000;
|
||||
}
|
||||
|
||||
static int max8952_list_voltage(struct regulator_dev *rdev,
|
||||
unsigned int selector)
|
||||
{
|
||||
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
|
||||
|
||||
if (rdev_get_id(rdev) != 0)
|
||||
return -EINVAL;
|
||||
|
||||
return max8952_voltage(max8952, selector);
|
||||
}
|
||||
|
||||
static int max8952_is_enabled(struct regulator_dev *rdev)
|
||||
{
|
||||
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
|
||||
return max8952->en;
|
||||
}
|
||||
|
||||
static int max8952_enable(struct regulator_dev *rdev)
|
||||
{
|
||||
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
|
||||
|
||||
/* If not valid, assume "ALWAYS_HIGH" */
|
||||
if (gpio_is_valid(max8952->pdata->gpio_en))
|
||||
gpio_set_value(max8952->pdata->gpio_en, 1);
|
||||
|
||||
max8952->en = true;
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int max8952_disable(struct regulator_dev *rdev)
|
||||
{
|
||||
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
|
||||
|
||||
/* If not valid, assume "ALWAYS_HIGH" -> not permitted */
|
||||
if (gpio_is_valid(max8952->pdata->gpio_en))
|
||||
gpio_set_value(max8952->pdata->gpio_en, 0);
|
||||
else
|
||||
return -EPERM;
|
||||
|
||||
max8952->en = false;
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int max8952_get_voltage(struct regulator_dev *rdev)
|
||||
{
|
||||
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
|
||||
u8 vid = 0;
|
||||
|
||||
if (max8952->vid0)
|
||||
vid += 1;
|
||||
if (max8952->vid1)
|
||||
vid += 2;
|
||||
|
||||
return max8952_voltage(max8952, vid);
|
||||
}
|
||||
|
||||
static int max8952_set_voltage(struct regulator_dev *rdev,
|
||||
int min_uV, int max_uV)
|
||||
{
|
||||
struct max8952_data *max8952 = rdev_get_drvdata(rdev);
|
||||
u8 vid = -1, i;
|
||||
|
||||
if (!gpio_is_valid(max8952->pdata->gpio_vid0) ||
|
||||
!gpio_is_valid(max8952->pdata->gpio_vid0)) {
|
||||
/* DVS not supported */
|
||||
return -EPERM;
|
||||
}
|
||||
|
||||
for (i = 0; i < MAX8952_NUM_DVS_MODE; i++) {
|
||||
int volt = max8952_voltage(max8952, i);
|
||||
|
||||
/* Set the voltage as low as possible within the range */
|
||||
if (volt <= max_uV && volt >= min_uV)
|
||||
if (vid == -1 || max8952_voltage(max8952, vid) > volt)
|
||||
vid = i;
|
||||
}
|
||||
|
||||
if (vid >= 0 && vid < MAX8952_NUM_DVS_MODE) {
|
||||
max8952->vid0 = (vid % 2 == 1);
|
||||
max8952->vid1 = (((vid >> 1) % 2) == 1);
|
||||
gpio_set_value(max8952->pdata->gpio_vid0, max8952->vid0);
|
||||
gpio_set_value(max8952->pdata->gpio_vid1, max8952->vid1);
|
||||
} else
|
||||
return -EINVAL;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct regulator_ops max8952_ops = {
|
||||
.list_voltage = max8952_list_voltage,
|
||||
.is_enabled = max8952_is_enabled,
|
||||
.enable = max8952_enable,
|
||||
.disable = max8952_disable,
|
||||
.get_voltage = max8952_get_voltage,
|
||||
.set_voltage = max8952_set_voltage,
|
||||
.set_suspend_disable = max8952_disable,
|
||||
};
|
||||
|
||||
static struct regulator_desc regulator = {
|
||||
.name = "MAX8952_VOUT",
|
||||
.id = 0,
|
||||
.n_voltages = MAX8952_NUM_DVS_MODE,
|
||||
.ops = &max8952_ops,
|
||||
.type = REGULATOR_VOLTAGE,
|
||||
.owner = THIS_MODULE,
|
||||
};
|
||||
|
||||
static int __devinit max8952_pmic_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *i2c_id)
|
||||
{
|
||||
struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
|
||||
struct max8952_platform_data *pdata = client->dev.platform_data;
|
||||
struct max8952_data *max8952;
|
||||
|
||||
int ret = 0, err = 0;
|
||||
|
||||
if (!pdata) {
|
||||
dev_err(&client->dev, "Require the platform data\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
|
||||
return -EIO;
|
||||
|
||||
max8952 = kzalloc(sizeof(struct max8952_data), GFP_KERNEL);
|
||||
if (!max8952)
|
||||
return -ENOMEM;
|
||||
|
||||
max8952->client = client;
|
||||
max8952->dev = &client->dev;
|
||||
max8952->pdata = pdata;
|
||||
mutex_init(&max8952->mutex);
|
||||
|
||||
max8952->rdev = regulator_register(®ulator, max8952->dev,
|
||||
&pdata->reg_data, max8952);
|
||||
|
||||
ret = IS_ERR(max8952->rdev);
|
||||
if (ret)
|
||||
dev_err(max8952->dev, "regulator init failed (%d)\n", ret);
|
||||
|
||||
max8952->en = !!(pdata->reg_data.constraints.boot_on);
|
||||
max8952->vid0 = (pdata->default_mode % 2) == 1;
|
||||
max8952->vid1 = ((pdata->default_mode >> 1) % 2) == 1;
|
||||
|
||||
if (gpio_is_valid(pdata->gpio_en)) {
|
||||
if (!gpio_request(pdata->gpio_en, "MAX8952 EN"))
|
||||
gpio_direction_output(pdata->gpio_en, max8952->en);
|
||||
else
|
||||
err = 1;
|
||||
} else
|
||||
err = 2;
|
||||
|
||||
if (err) {
|
||||
dev_info(max8952->dev, "EN gpio invalid: assume that EN"
|
||||
"is always High\n");
|
||||
max8952->en = 1;
|
||||
pdata->gpio_en = -1; /* Mark invalid */
|
||||
}
|
||||
|
||||
err = 0;
|
||||
|
||||
if (gpio_is_valid(pdata->gpio_vid0) &&
|
||||
gpio_is_valid(pdata->gpio_vid1)) {
|
||||
if (!gpio_request(pdata->gpio_vid0, "MAX8952 VID0"))
|
||||
gpio_direction_output(pdata->gpio_vid0,
|
||||
(pdata->default_mode) % 2);
|
||||
else
|
||||
err = 1;
|
||||
|
||||
if (!gpio_request(pdata->gpio_vid1, "MAX8952 VID1"))
|
||||
gpio_direction_output(pdata->gpio_vid1,
|
||||
(pdata->default_mode >> 1) % 2);
|
||||
else {
|
||||
if (!err)
|
||||
gpio_free(pdata->gpio_vid0);
|
||||
err = 2;
|
||||
}
|
||||
|
||||
} else
|
||||
err = 3;
|
||||
|
||||
if (err) {
|
||||
dev_warn(max8952->dev, "VID0/1 gpio invalid: "
|
||||
"DVS not avilable.\n");
|
||||
max8952->vid0 = 0;
|
||||
max8952->vid1 = 0;
|
||||
/* Mark invalid */
|
||||
pdata->gpio_vid0 = -1;
|
||||
pdata->gpio_vid1 = -1;
|
||||
|
||||
/* Disable Pulldown of EN only */
|
||||
max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x60);
|
||||
|
||||
dev_err(max8952->dev, "DVS modes disabled because VID0 and VID1"
|
||||
" do not have proper controls.\n");
|
||||
} else {
|
||||
/*
|
||||
* Disable Pulldown on EN, VID0, VID1 to reduce
|
||||
* leakage current of MAX8952 assuming that MAX8952
|
||||
* is turned on (EN==1). Note that without having VID0/1
|
||||
* properly connected, turning pulldown off can be
|
||||
* problematic. Thus, turn this off only when they are
|
||||
* controllable by GPIO.
|
||||
*/
|
||||
max8952_write_reg(max8952, MAX8952_REG_CONTROL, 0x0);
|
||||
}
|
||||
|
||||
max8952_write_reg(max8952, MAX8952_REG_MODE0,
|
||||
(max8952_read_reg(max8952,
|
||||
MAX8952_REG_MODE0) & 0xC0) |
|
||||
(pdata->dvs_mode[0] & 0x3F));
|
||||
max8952_write_reg(max8952, MAX8952_REG_MODE1,
|
||||
(max8952_read_reg(max8952,
|
||||
MAX8952_REG_MODE1) & 0xC0) |
|
||||
(pdata->dvs_mode[1] & 0x3F));
|
||||
max8952_write_reg(max8952, MAX8952_REG_MODE2,
|
||||
(max8952_read_reg(max8952,
|
||||
MAX8952_REG_MODE2) & 0xC0) |
|
||||
(pdata->dvs_mode[2] & 0x3F));
|
||||
max8952_write_reg(max8952, MAX8952_REG_MODE3,
|
||||
(max8952_read_reg(max8952,
|
||||
MAX8952_REG_MODE3) & 0xC0) |
|
||||
(pdata->dvs_mode[3] & 0x3F));
|
||||
|
||||
max8952_write_reg(max8952, MAX8952_REG_SYNC,
|
||||
(max8952_read_reg(max8952, MAX8952_REG_SYNC) & 0x3F) |
|
||||
((pdata->sync_freq & 0x3) << 6));
|
||||
max8952_write_reg(max8952, MAX8952_REG_RAMP,
|
||||
(max8952_read_reg(max8952, MAX8952_REG_RAMP) & 0x1F) |
|
||||
((pdata->ramp_speed & 0x7) << 5));
|
||||
|
||||
i2c_set_clientdata(client, max8952);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int __devexit max8952_pmic_remove(struct i2c_client *client)
|
||||
{
|
||||
struct max8952_data *max8952 = i2c_get_clientdata(client);
|
||||
struct max8952_platform_data *pdata = max8952->pdata;
|
||||
struct regulator_dev *rdev = max8952->rdev;
|
||||
|
||||
regulator_unregister(rdev);
|
||||
|
||||
gpio_free(pdata->gpio_vid0);
|
||||
gpio_free(pdata->gpio_vid1);
|
||||
gpio_free(pdata->gpio_en);
|
||||
|
||||
kfree(max8952);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct i2c_device_id max8952_ids[] = {
|
||||
{ "max8952", 0 },
|
||||
{ },
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, max8952_ids);
|
||||
|
||||
static struct i2c_driver max8952_pmic_driver = {
|
||||
.probe = max8952_pmic_probe,
|
||||
.remove = __devexit_p(max8952_pmic_remove),
|
||||
.driver = {
|
||||
.name = "max8952",
|
||||
},
|
||||
.id_table = max8952_ids,
|
||||
};
|
||||
|
||||
static int __init max8952_pmic_init(void)
|
||||
{
|
||||
return i2c_add_driver(&max8952_pmic_driver);
|
||||
}
|
||||
subsys_initcall(max8952_pmic_init);
|
||||
|
||||
static void __exit max8952_pmic_exit(void)
|
||||
{
|
||||
i2c_del_driver(&max8952_pmic_driver);
|
||||
}
|
||||
module_exit(max8952_pmic_exit);
|
||||
|
||||
MODULE_DESCRIPTION("MAXIM 8952 voltage regulator driver");
|
||||
MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
|
||||
MODULE_LICENSE("GPL");
|
||||
|
|
@ -0,0 +1,135 @@
|
|||
/*
|
||||
* max8952.h - Voltage regulation for the Maxim 8952
|
||||
*
|
||||
* Copyright (C) 2010 Samsung Electrnoics
|
||||
* MyungJoo Ham <myungjoo.ham@samsung.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
||||
*/
|
||||
|
||||
#ifndef REGULATOR_MAX8952
|
||||
#define REGULATOR_MAX8952
|
||||
|
||||
#include <linux/regulator/machine.h>
|
||||
|
||||
enum {
|
||||
MAX8952_DVS_MODE0,
|
||||
MAX8952_DVS_MODE1,
|
||||
MAX8952_DVS_MODE2,
|
||||
MAX8952_DVS_MODE3,
|
||||
};
|
||||
|
||||
enum {
|
||||
MAX8952_DVS_770mV = 0,
|
||||
MAX8952_DVS_780mV,
|
||||
MAX8952_DVS_790mV,
|
||||
MAX8952_DVS_800mV,
|
||||
MAX8952_DVS_810mV,
|
||||
MAX8952_DVS_820mV,
|
||||
MAX8952_DVS_830mV,
|
||||
MAX8952_DVS_840mV,
|
||||
MAX8952_DVS_850mV,
|
||||
MAX8952_DVS_860mV,
|
||||
MAX8952_DVS_870mV,
|
||||
MAX8952_DVS_880mV,
|
||||
MAX8952_DVS_890mV,
|
||||
MAX8952_DVS_900mV,
|
||||
MAX8952_DVS_910mV,
|
||||
MAX8952_DVS_920mV,
|
||||
MAX8952_DVS_930mV,
|
||||
MAX8952_DVS_940mV,
|
||||
MAX8952_DVS_950mV,
|
||||
MAX8952_DVS_960mV,
|
||||
MAX8952_DVS_970mV,
|
||||
MAX8952_DVS_980mV,
|
||||
MAX8952_DVS_990mV,
|
||||
MAX8952_DVS_1000mV,
|
||||
MAX8952_DVS_1010mV,
|
||||
MAX8952_DVS_1020mV,
|
||||
MAX8952_DVS_1030mV,
|
||||
MAX8952_DVS_1040mV,
|
||||
MAX8952_DVS_1050mV,
|
||||
MAX8952_DVS_1060mV,
|
||||
MAX8952_DVS_1070mV,
|
||||
MAX8952_DVS_1080mV,
|
||||
MAX8952_DVS_1090mV,
|
||||
MAX8952_DVS_1100mV,
|
||||
MAX8952_DVS_1110mV,
|
||||
MAX8952_DVS_1120mV,
|
||||
MAX8952_DVS_1130mV,
|
||||
MAX8952_DVS_1140mV,
|
||||
MAX8952_DVS_1150mV,
|
||||
MAX8952_DVS_1160mV,
|
||||
MAX8952_DVS_1170mV,
|
||||
MAX8952_DVS_1180mV,
|
||||
MAX8952_DVS_1190mV,
|
||||
MAX8952_DVS_1200mV,
|
||||
MAX8952_DVS_1210mV,
|
||||
MAX8952_DVS_1220mV,
|
||||
MAX8952_DVS_1230mV,
|
||||
MAX8952_DVS_1240mV,
|
||||
MAX8952_DVS_1250mV,
|
||||
MAX8952_DVS_1260mV,
|
||||
MAX8952_DVS_1270mV,
|
||||
MAX8952_DVS_1280mV,
|
||||
MAX8952_DVS_1290mV,
|
||||
MAX8952_DVS_1300mV,
|
||||
MAX8952_DVS_1310mV,
|
||||
MAX8952_DVS_1320mV,
|
||||
MAX8952_DVS_1330mV,
|
||||
MAX8952_DVS_1340mV,
|
||||
MAX8952_DVS_1350mV,
|
||||
MAX8952_DVS_1360mV,
|
||||
MAX8952_DVS_1370mV,
|
||||
MAX8952_DVS_1380mV,
|
||||
MAX8952_DVS_1390mV,
|
||||
MAX8952_DVS_1400mV,
|
||||
};
|
||||
|
||||
enum {
|
||||
MAX8952_SYNC_FREQ_26MHZ, /* Default */
|
||||
MAX8952_SYNC_FREQ_13MHZ,
|
||||
MAX8952_SYNC_FREQ_19_2MHZ,
|
||||
};
|
||||
|
||||
enum {
|
||||
MAX8952_RAMP_32mV_us = 0, /* Default */
|
||||
MAX8952_RAMP_16mV_us,
|
||||
MAX8952_RAMP_8mV_us,
|
||||
MAX8952_RAMP_4mV_us,
|
||||
MAX8952_RAMP_2mV_us,
|
||||
MAX8952_RAMP_1mV_us,
|
||||
MAX8952_RAMP_0_5mV_us,
|
||||
MAX8952_RAMP_0_25mV_us,
|
||||
};
|
||||
|
||||
#define MAX8952_NUM_DVS_MODE 4
|
||||
|
||||
struct max8952_platform_data {
|
||||
int gpio_vid0;
|
||||
int gpio_vid1;
|
||||
int gpio_en;
|
||||
|
||||
u8 default_mode;
|
||||
u8 dvs_mode[MAX8952_NUM_DVS_MODE]; /* MAX8952_DVS_MODEx_XXXXmV */
|
||||
|
||||
u8 sync_freq;
|
||||
u8 ramp_speed;
|
||||
|
||||
struct regulator_init_data reg_data;
|
||||
};
|
||||
|
||||
|
||||
#endif /* REGULATOR_MAX8952 */
|
||||
Loading…
Reference in New Issue