From b6ef36d2c1e391adc1fe1b2dd2a0f887a9f3052b Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Mon, 4 Apr 2016 17:37:46 -0700 Subject: [PATCH 01/17] watchdog: qcom: Report reboot reason The Qualcom watchdog timer block reports if the system was reset by the watchdog. Pass the information to user space. Reviewed-by: Grant Grundler Tested-by: Grant Grundler Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/qcom-wdt.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c index 20563ccb7be0..a043fa4f60e5 100644 --- a/drivers/watchdog/qcom-wdt.c +++ b/drivers/watchdog/qcom-wdt.c @@ -21,6 +21,7 @@ #define WDT_RST 0x38 #define WDT_EN 0x40 +#define WDT_STS 0x44 #define WDT_BITE_TIME 0x5C struct qcom_wdt { @@ -108,7 +109,8 @@ static const struct watchdog_ops qcom_wdt_ops = { static const struct watchdog_info qcom_wdt_info = { .options = WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE - | WDIOF_SETTIMEOUT, + | WDIOF_SETTIMEOUT + | WDIOF_CARDRESET, .identity = KBUILD_MODNAME, }; @@ -171,6 +173,9 @@ static int qcom_wdt_probe(struct platform_device *pdev) wdt->wdd.max_timeout = 0x10000000U / wdt->rate; wdt->wdd.parent = &pdev->dev; + if (readl(wdt->base + WDT_STS) & 1) + wdt->wdd.bootstatus = WDIOF_CARDRESET; + /* * If 'timeout-sec' unspecified in devicetree, assume a 30 second * default, unless the max timeout is less than 30 seconds, then use From ebbf677a3fb54fda56c58fc985c4617c215da6a0 Mon Sep 17 00:00:00 2001 From: Richard Cochran Date: Fri, 18 Mar 2016 22:26:08 +0100 Subject: [PATCH 02/17] watchdog: octeon: Handle the FROZEN hot plug notifier actions. When performing a suspend operation, the kernel brings all of the non-boot CPUs offline, calling the hot plug notifiers with the flag, CPU_TASKS_FROZEN, set in the action code. Similarly, during resume, the CPUs are brought back online, but again the notifiers have the FROZEN flag set. While some very few drivers really need to treat suspend/resume specially, this driver unintentionally ignores the notifications. This patch changes the driver to disable the watchdog interrupt whenever the CPU goes offline, and to enable it whenever the CPU goes back online. As a result, the suspended state is no longer a special case that leaves the watchdog active. Signed-off-by: Richard Cochran Cc: linux-watchdog@vger.kernel.org Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/octeon-wdt-main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/watchdog/octeon-wdt-main.c b/drivers/watchdog/octeon-wdt-main.c index 14521c8b3d5a..b55981f88a08 100644 --- a/drivers/watchdog/octeon-wdt-main.c +++ b/drivers/watchdog/octeon-wdt-main.c @@ -431,7 +431,7 @@ static int octeon_wdt_cpu_callback(struct notifier_block *nfb, { unsigned int cpu = (unsigned long)hcpu; - switch (action) { + switch (action & ~CPU_TASKS_FROZEN) { case CPU_DOWN_PREPARE: octeon_wdt_disable_interrupt(cpu); break; From bc677ff42e81bbf78308a7b66cf7b63b0f5c26b0 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Fri, 1 Apr 2016 08:16:43 -0700 Subject: [PATCH 03/17] watchdog: imx2_wdt: add external reset support via dt prop The IMX6 watchdog supports assertion of a signal (WDOG_B) which can be pinmux'd to an external pin. This is typically used for boards that have PMIC's in control of the IMX6 power rails. In fact, failure to use such an external reset on boards with external PMIC's can result in various hangs due to the IMX6 not being fully reset [1] as well as the board failing to reset because its PMIC has not been reset to provide adequate voltage for the CPU when coming out of reset at 800Mhz. This uses a new device-tree property 'fsl,ext-reset-output' to indicate the board has such a reset and to cause the watchdog to be configured to assert WDOG_B instead of an internal reset both on a watchdog timeout and in system_restart. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/333689.html Cc: Fabio Estevam Cc: Lucas Stach Cc: Stefan Roese Cc: Iain Paton Cc: Sascha Hauer Signed-off-by: Tim Harvey Reviewed-by: Lucas Stach Acked-by: Shawn Guo Tested-by: Akshay Bhat Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- .../bindings/watchdog/fsl-imx-wdt.txt | 4 +++- drivers/watchdog/imx2_wdt.c | 19 +++++++++++++++++-- 2 files changed, 20 insertions(+), 3 deletions(-) diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index 8dab6fd024aa..107280ef0025 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -5,10 +5,12 @@ Required properties: - reg : Should contain WDT registers location and length - interrupts : Should contain WDT interrupt -Optional property: +Optional properties: - big-endian: If present the watchdog device's registers are implemented in big endian mode, otherwise in native mode(same with CPU), for more detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. +- fsl,ext-reset-output: If present the watchdog device is configured to + assert its external reset (WDOG_B) instead of issuing a software reset. Examples: diff --git a/drivers/watchdog/imx2_wdt.c b/drivers/watchdog/imx2_wdt.c index 331aed831dac..62f346bb4348 100644 --- a/drivers/watchdog/imx2_wdt.c +++ b/drivers/watchdog/imx2_wdt.c @@ -37,6 +37,8 @@ #define IMX2_WDT_WCR 0x00 /* Control Register */ #define IMX2_WDT_WCR_WT (0xFF << 8) /* -> Watchdog Timeout Field */ +#define IMX2_WDT_WCR_WDA (1 << 5) /* -> External Reset WDOG_B */ +#define IMX2_WDT_WCR_SRS (1 << 4) /* -> Software Reset Signal */ #define IMX2_WDT_WCR_WRE (1 << 3) /* -> WDOG Reset Enable */ #define IMX2_WDT_WCR_WDE (1 << 2) /* -> Watchdog Enable */ #define IMX2_WDT_WCR_WDZST (1 << 0) /* -> Watchdog timer Suspend */ @@ -59,6 +61,7 @@ struct imx2_wdt_device { struct clk *clk; struct regmap *regmap; struct watchdog_device wdog; + bool ext_reset; }; static bool nowayout = WATCHDOG_NOWAYOUT; @@ -83,6 +86,12 @@ static int imx2_wdt_restart(struct watchdog_device *wdog, unsigned long action, struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog); unsigned int wcr_enable = IMX2_WDT_WCR_WDE; + /* Use internal reset or external - not both */ + if (wdev->ext_reset) + wcr_enable |= IMX2_WDT_WCR_SRS; /* do not assert int reset */ + else + wcr_enable |= IMX2_WDT_WCR_WDA; /* do not assert ext-reset */ + /* Assert SRS signal */ regmap_write(wdev->regmap, IMX2_WDT_WCR, wcr_enable); /* @@ -112,8 +121,12 @@ static inline void imx2_wdt_setup(struct watchdog_device *wdog) val |= IMX2_WDT_WCR_WDZST; /* Strip the old watchdog Time-Out value */ val &= ~IMX2_WDT_WCR_WT; - /* Generate reset if WDOG times out */ - val &= ~IMX2_WDT_WCR_WRE; + /* Generate internal chip-level reset if WDOG times out */ + if (!wdev->ext_reset) + val &= ~IMX2_WDT_WCR_WRE; + /* Or if external-reset assert WDOG_B reset only on time-out */ + else + val |= IMX2_WDT_WCR_WRE; /* Keep Watchdog Disabled */ val &= ~IMX2_WDT_WCR_WDE; /* Set the watchdog's Time-Out value */ @@ -230,6 +243,8 @@ static int __init imx2_wdt_probe(struct platform_device *pdev) regmap_read(wdev->regmap, IMX2_WDT_WRSR, &val); wdog->bootstatus = val & IMX2_WDT_WRSR_TOUT ? WDIOF_CARDRESET : 0; + wdev->ext_reset = of_property_read_bool(pdev->dev.of_node, + "fsl,ext-reset-output"); wdog->timeout = clamp_t(unsigned, timeout, 1, IMX2_WDT_MAX_TIME); if (wdog->timeout != timeout) dev_warn(&pdev->dev, "Initial timeout out of range! Clamped from %u to %u\n", From 84df082cad236a6ec70df1fbbf3d8dcb5c5f994e Mon Sep 17 00:00:00 2001 From: Nigel Croxon Date: Wed, 6 Apr 2016 14:40:05 -0400 Subject: [PATCH 04/17] watchdog: hpwdt: Adjust documentation to match latest kernel module parameters. Adjust documentation to match latest kernel module parameters. Signed-off-by: Nigel Croxon Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- Documentation/watchdog/hpwdt.txt | 57 +++++++++++++++++--------------- 1 file changed, 30 insertions(+), 27 deletions(-) diff --git a/Documentation/watchdog/hpwdt.txt b/Documentation/watchdog/hpwdt.txt index 9488078900e0..a40398cce9d1 100644 --- a/Documentation/watchdog/hpwdt.txt +++ b/Documentation/watchdog/hpwdt.txt @@ -1,64 +1,67 @@ -Last reviewed: 06/02/2009 +Last reviewed: 04/04/2016 - HP iLO2 NMI Watchdog Driver - NMI sourcing for iLO2 based ProLiant Servers + HPE iLO NMI Watchdog Driver + NMI sourcing for iLO based ProLiant Servers Documentation and Driver by - Thomas Mingarelli + Thomas Mingarelli - The HP iLO2 NMI Watchdog driver is a kernel module that provides basic + The HPE iLO NMI Watchdog driver is a kernel module that provides basic watchdog functionality and the added benefit of NMI sourcing. Both the watchdog functionality and the NMI sourcing capability need to be enabled by the user. Remember that the two modes are not dependent on one another. A user can have the NMI sourcing without the watchdog timer and vice-versa. + All references to iLO in this document imply it also works on iLO2 and all + subsequent generations. Watchdog functionality is enabled like any other common watchdog driver. That is, an application needs to be started that kicks off the watchdog timer. A basic application exists in the Documentation/watchdog/src directory called watchdog-test.c. Simply compile the C file and kick it off. If the system - gets into a bad state and hangs, the HP ProLiant iLO 2 timer register will + gets into a bad state and hangs, the HPE ProLiant iLO timer register will not be updated in a timely fashion and a hardware system reset (also known as an Automatic Server Recovery (ASR)) event will occur. - The hpwdt driver also has four (4) module parameters. They are the following: + The hpwdt driver also has three (3) module parameters. They are the following: - soft_margin - allows the user to set the watchdog timer value - allow_kdump - allows the user to save off a kernel dump image after an NMI + soft_margin - allows the user to set the watchdog timer value. + Default value is 30 seconds. + allow_kdump - allows the user to save off a kernel dump image after an NMI. + Default value is 1/ON nowayout - basic watchdog parameter that does not allow the timer to be restarted or an impending ASR to be escaped. - priority - determines whether or not the hpwdt driver is first on the - die_notify list to handle NMIs or last. The default value - for this module parameter is 0 or LAST. If the user wants to - enable NMI sourcing then reload the hpwdt driver with - priority=1 (and boot with nmi_watchdog=0). + Default value is set when compiling the kernel. If it is set + to "Y", then there is no way of disabling the watchdog once + it has been started. NOTE: More information about watchdog drivers in general, including the ioctl interface to /dev/watchdog can be found in Documentation/watchdog/watchdog-api.txt and Documentation/IPMI.txt. - The priority parameter was introduced due to other kernel software that relied - on handling NMIs (like oprofile). Keeping hpwdt's priority at 0 (or LAST) - enables the users of NMIs for non critical events to be work as expected. - The NMI sourcing capability is disabled by default due to the inability to distinguish between "NMI Watchdog Ticks" and "HW generated NMI events" in the Linux kernel. What this means is that the hpwdt nmi handler code is called each time the NMI signal fires off. This could amount to several thousands of NMIs in a matter of seconds. If a user sees the Linux kernel's "dazed and confused" message in the logs or if the system gets into a hung state, then - the hpwdt driver can be reloaded with the "priority" module parameter set - (priority=1). + the hpwdt driver can be reloaded. 1. If the kernel has not been booted with nmi_watchdog turned off then - edit /boot/grub/menu.lst and place the nmi_watchdog=0 at the end of the - currently booting kernel line. + edit and place the nmi_watchdog=0 at the end of the currently booting + kernel line. Depending on your Linux distribution and platform setup: + For non-UEFI systems + /boot/grub/grub.conf or + /boot/grub/menu.lst + For UEFI systems + /boot/efi/EFI/distroname/grub.conf or + /boot/efi/efi/distroname/elilo.conf 2. reboot the sever - 3. Once the system comes up perform a rmmod hpwdt - 4. insmod /lib/modules/`uname -r`/kernel/drivers/char/watchdog/hpwdt.ko priority=1 + 3. Once the system comes up perform a modprobe -r hpwdt + 4. modprobe /lib/modules/`uname -r`/kernel/drivers/watchdog/hpwdt.ko Now, the hpwdt can successfully receive and source the NMI and provide a log - message that details the reason for the NMI (as determined by the HP BIOS). + message that details the reason for the NMI (as determined by the HPE BIOS). - Below is a list of NMIs the HP BIOS understands along with the associated + Below is a list of NMIs the HPE BIOS understands along with the associated code (reason): No source found 00h @@ -92,4 +95,4 @@ Last reviewed: 06/02/2009 -- Tom Mingarelli - (thomas.mingarelli@hp.com) + (thomas.mingarelli@hpe.com) From 358d5a565fa6a5f51fcd04f8e890a0a474a814fe Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 12 Apr 2016 17:56:11 +0200 Subject: [PATCH 05/17] watchdog: core: fix trivial typo in a comment Let's have balanced round brackets. Signed-off-by: Wolfram Sang Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/watchdog_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/watchdog/watchdog_core.c b/drivers/watchdog/watchdog_core.c index c1658fe73d58..6249ed34214a 100644 --- a/drivers/watchdog/watchdog_core.c +++ b/drivers/watchdog/watchdog_core.c @@ -104,7 +104,7 @@ static void watchdog_check_min_max_timeout(struct watchdog_device *wdd) * timeout module parameter (if it is valid value) or the timeout-sec property * (only if it is a valid value and the timeout_parm is out of bounds). * If none of them are valid then we keep the old value (which should normally - * be the default timeout value. + * be the default timeout value). * * A zero is returned on success and -EINVAL for failure. */ From e1f30282a1d3d0c75d5a08e47c6ac1563065be52 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Thu, 21 Apr 2016 07:38:14 -0700 Subject: [PATCH 06/17] watchdog: core: Fix circular locking dependency lockdep reports the following circular locking dependency. ====================================================== INFO: possible circular locking dependency detected ] 4.6.0-rc3-00191-gfabf418 #162 Not tainted ------------------------------------------------------- systemd/1 is trying to acquire lock: ((&(&wd_data->work)->work)){+.+...}, at: [<80141650>] flush_work+0x0/0x280 but task is already holding lock: (&wd_data->lock){+.+...}, at: [<804acfa8>] watchdog_release+0x18/0x190 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&wd_data->lock){+.+...}: [<80662310>] mutex_lock_nested+0x64/0x4a8 [<804aca4c>] watchdog_ping_work+0x18/0x4c [<80143128>] process_one_work+0x1ac/0x500 [<801434b4>] worker_thread+0x38/0x554 [<80149510>] kthread+0xf4/0x108 [<80107c10>] ret_from_fork+0x14/0x24 -> #0 ((&(&wd_data->work)->work)){+.+...}: [<8017c4e8>] lock_acquire+0x70/0x90 [<8014169c>] flush_work+0x4c/0x280 [<801440f8>] __cancel_work_timer+0x9c/0x1e0 [<804acfcc>] watchdog_release+0x3c/0x190 [<8022c5e8>] __fput+0x80/0x1c8 [<80147b28>] task_work_run+0x94/0xc8 [<8010b998>] do_work_pending+0x8c/0xb4 [<80107ba8>] slow_work_pending+0xc/0x20 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&wd_data->lock); lock((&(&wd_data->work)->work)); lock(&wd_data->lock); lock((&(&wd_data->work)->work)); *** DEADLOCK *** 1 lock held by systemd/1: stack backtrace: CPU: 2 PID: 1 Comm: systemd Not tainted 4.6.0-rc3-00191-gfabf418 #162 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [<8010f5e4>] (unwind_backtrace) from [<8010c038>] (show_stack+0x10/0x14) [<8010c038>] (show_stack) from [<8039d7fc>] (dump_stack+0xa8/0xd4) [<8039d7fc>] (dump_stack) from [<80177ee0>] (print_circular_bug+0x214/0x334) [<80177ee0>] (print_circular_bug) from [<80179230>] (check_prevs_add+0x4dc/0x8e8) [<80179230>] (check_prevs_add) from [<8017b3d8>] (__lock_acquire+0xc6c/0x14ec) [<8017b3d8>] (__lock_acquire) from [<8017c4e8>] (lock_acquire+0x70/0x90) [<8017c4e8>] (lock_acquire) from [<8014169c>] (flush_work+0x4c/0x280) [<8014169c>] (flush_work) from [<801440f8>] (__cancel_work_timer+0x9c/0x1e0) [<801440f8>] (__cancel_work_timer) from [<804acfcc>] (watchdog_release+0x3c/0x190) [<804acfcc>] (watchdog_release) from [<8022c5e8>] (__fput+0x80/0x1c8) [<8022c5e8>] (__fput) from [<80147b28>] (task_work_run+0x94/0xc8) [<80147b28>] (task_work_run) from [<8010b998>] (do_work_pending+0x8c/0xb4) [<8010b998>] (do_work_pending) from [<80107ba8>] (slow_work_pending+0xc/0x20) Turns out the call to cancel_delayed_work_sync() in watchdog_release() is not necessary and can be dropped. If the worker is no longer necessary, the subsequent call to watchdog_update_worker() will cancel it. If it is already running, it won't do anything, since the worker function checks if it needs to ping the watchdog or not. Reported-by: Clemens Gruber Tested-by: Clemens Gruber Fixes: 11d7aba9ceb7 ("watchdog: imx2: Convert to use infrastructure triggered keepalives") Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck Cc: stable --- drivers/watchdog/watchdog_dev.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/watchdog/watchdog_dev.c b/drivers/watchdog/watchdog_dev.c index e2c5abbb45ff..3595cffa24ea 100644 --- a/drivers/watchdog/watchdog_dev.c +++ b/drivers/watchdog/watchdog_dev.c @@ -736,7 +736,6 @@ static int watchdog_release(struct inode *inode, struct file *file) watchdog_ping(wdd); } - cancel_delayed_work_sync(&wd_data->work); watchdog_update_worker(wdd); /* make sure that /dev/watchdog can be re-opened */ From 46856fabe40cc80f92134683cdec7dc0fc8f4000 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Tue, 3 May 2016 19:15:58 +0200 Subject: [PATCH 07/17] watchdog: sp5100_tco: properly check for new register layouts Commits 190aa4304de6 (Add AMD Mullins platform support) and cca118fa2a0a94 (Add AMD Carrizo platform support) enabled the driver on a lot more devices, but the following commit missed a single location in the code when checking if the SB800 register offsets should be used. This leads to the wrong register being written which in turn causes ACPI to go haywire. Fix this by introducing a helper function to check for the new register layout and use this consistently. https://bugzilla.kernel.org/show_bug.cgi?id=114201 https://bugzilla.redhat.com/show_bug.cgi?id=1329910 Fixes: bdecfcdb5461 (sp5100_tco: fix the device check for SB800 and later chipsets) Cc: stable@vger.kernel.org (4.5+) Signed-off-by: Lucas Stach Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/sp5100_tco.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) diff --git a/drivers/watchdog/sp5100_tco.c b/drivers/watchdog/sp5100_tco.c index 6467b91f2245..028618c5eeba 100644 --- a/drivers/watchdog/sp5100_tco.c +++ b/drivers/watchdog/sp5100_tco.c @@ -73,6 +73,13 @@ MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started." /* * Some TCO specific functions */ + +static bool tco_has_sp5100_reg_layout(struct pci_dev *dev) +{ + return dev->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS && + dev->revision < 0x40; +} + static void tco_timer_start(void) { u32 val; @@ -129,7 +136,7 @@ static void tco_timer_enable(void) { int val; - if (sp5100_tco_pci->revision >= 0x40) { + if (!tco_has_sp5100_reg_layout(sp5100_tco_pci)) { /* For SB800 or later */ /* Set the Watchdog timer resolution to 1 sec */ outb(SB800_PM_WATCHDOG_CONFIG, SB800_IO_PM_INDEX_REG); @@ -342,8 +349,7 @@ static unsigned char sp5100_tco_setupdevice(void) /* * Determine type of southbridge chipset. */ - if (sp5100_tco_pci->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS && - sp5100_tco_pci->revision < 0x40) { + if (tco_has_sp5100_reg_layout(sp5100_tco_pci)) { dev_name = SP5100_DEVNAME; index_reg = SP5100_IO_PM_INDEX_REG; data_reg = SP5100_IO_PM_DATA_REG; @@ -388,8 +394,7 @@ static unsigned char sp5100_tco_setupdevice(void) * Secondly, Find the watchdog timer MMIO address * from SBResource_MMIO register. */ - if (sp5100_tco_pci->device == PCI_DEVICE_ID_ATI_SBX00_SMBUS && - sp5100_tco_pci->revision < 0x40) { + if (tco_has_sp5100_reg_layout(sp5100_tco_pci)) { /* Read SBResource_MMIO from PCI config(PCI_Reg: 9Ch) */ pci_read_config_dword(sp5100_tco_pci, SP5100_SB_RESOURCE_MMIO_BASE, &val); From ea0c03e80ccd99cb0ab208397da5a417dabf9a22 Mon Sep 17 00:00:00 2001 From: Knud Poulsen Date: Mon, 25 Apr 2016 12:28:51 +0200 Subject: [PATCH 08/17] watchdog: f71808e_wdt: Add F81865 support Adds watchdog enable support for Fintek F81865 Super-IO chip to Fintek wdt driver (f71808e_wdt) Tested and verified on Lanner LEC-3030 Industrial PC Datasheet references: http://www.hardwaresecrets.com/datasheets/F81865_V028P.pdf http://www.alldatasheet.com/datasheet-pdf/pdf/406317/FINTEK/F81865.html Signed-off-by: Knud Poulsen Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/f71808e_wdt.c | 24 +++++++++++++++++++++--- 1 file changed, 21 insertions(+), 3 deletions(-) diff --git a/drivers/watchdog/f71808e_wdt.c b/drivers/watchdog/f71808e_wdt.c index 016bd9355190..f650e89d8bec 100644 --- a/drivers/watchdog/f71808e_wdt.c +++ b/drivers/watchdog/f71808e_wdt.c @@ -59,6 +59,7 @@ #define SIO_F71869A_ID 0x1007 /* Chipset ID */ #define SIO_F71882_ID 0x0541 /* Chipset ID */ #define SIO_F71889_ID 0x0723 /* Chipset ID */ +#define SIO_F81865_ID 0x0704 /* Chipset ID */ #define F71808FG_REG_WDO_CONF 0xf0 #define F71808FG_REG_WDT_CONF 0xf5 @@ -71,6 +72,9 @@ #define F71808FG_FLAG_WD_PULSE 4 #define F71808FG_FLAG_WD_UNIT 3 +#define F81865_REG_WDO_CONF 0xfa +#define F81865_FLAG_WDOUT_EN 0 + /* Default values */ #define WATCHDOG_TIMEOUT 60 /* 1 minute default timeout */ #define WATCHDOG_MAX_TIMEOUT (60 * 255) @@ -112,7 +116,7 @@ module_param(start_withtimeout, uint, 0); MODULE_PARM_DESC(start_withtimeout, "Start watchdog timer on module load with" " given initial timeout. Zero (default) disables this feature."); -enum chips { f71808fg, f71858fg, f71862fg, f71869, f71882fg, f71889fg }; +enum chips { f71808fg, f71858fg, f71862fg, f71869, f71882fg, f71889fg, f81865 }; static const char *f71808e_names[] = { "f71808fg", @@ -121,6 +125,7 @@ static const char *f71808e_names[] = { "f71869", "f71882fg", "f71889fg", + "f81865", }; /* Super-I/O Function prototypes */ @@ -360,6 +365,11 @@ static int watchdog_start(void) superio_inb(watchdog.sioaddr, SIO_REG_MFUNCT3) & 0xcf); break; + case f81865: + /* Set pin 70 to WDTRST# */ + superio_clear_bit(watchdog.sioaddr, SIO_REG_MFUNCT3, 5); + break; + default: /* * 'default' label to shut up the compiler and catch @@ -371,8 +381,13 @@ static int watchdog_start(void) superio_select(watchdog.sioaddr, SIO_F71808FG_LD_WDT); superio_set_bit(watchdog.sioaddr, SIO_REG_ENABLE, 0); - superio_set_bit(watchdog.sioaddr, F71808FG_REG_WDO_CONF, - F71808FG_FLAG_WDOUT_EN); + + if (watchdog.type == f81865) + superio_set_bit(watchdog.sioaddr, F81865_REG_WDO_CONF, + F81865_FLAG_WDOUT_EN); + else + superio_set_bit(watchdog.sioaddr, F71808FG_REG_WDO_CONF, + F71808FG_FLAG_WDOUT_EN); superio_set_bit(watchdog.sioaddr, F71808FG_REG_WDT_CONF, F71808FG_FLAG_WD_EN); @@ -770,6 +785,9 @@ static int __init f71808e_find(int sioaddr) /* Confirmed (by datasheet) not to have a watchdog. */ err = -ENODEV; goto exit; + case SIO_F81865_ID: + watchdog.type = f81865; + break; default: pr_info("Unrecognized Fintek device: %04x\n", (unsigned int)devid); From 85c130a8bf542205a84edbca225972375fcb07eb Mon Sep 17 00:00:00 2001 From: Knud Poulsen Date: Mon, 25 Apr 2016 17:34:47 +0200 Subject: [PATCH 09/17] watchdog: f71808e_wdt: Fix typo Spelling/ typo Signed-off-by: Knud Poulsen Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/f71808e_wdt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/watchdog/f71808e_wdt.c b/drivers/watchdog/f71808e_wdt.c index f650e89d8bec..c1e95bcdf911 100644 --- a/drivers/watchdog/f71808e_wdt.c +++ b/drivers/watchdog/f71808e_wdt.c @@ -38,7 +38,7 @@ #define SIO_F71808FG_LD_WDT 0x07 /* Watchdog timer logical device */ #define SIO_UNLOCK_KEY 0x87 /* Key to enable Super-I/O */ -#define SIO_LOCK_KEY 0xAA /* Key to diasble Super-I/O */ +#define SIO_LOCK_KEY 0xAA /* Key to disable Super-I/O */ #define SIO_REG_LDSEL 0x07 /* Logical device select */ #define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */ From b97cb21a46341575c6cbe3d327a08b99030c3aee Mon Sep 17 00:00:00 2001 From: Knud Poulsen Date: Tue, 26 Apr 2016 08:44:16 +0200 Subject: [PATCH 10/17] watchdog: f71808e_wdt: Fix WDTMOUT_STS register read Tested and verified on Lanner LEC-3030 Industrial PC (with F81865) Datasheet verified for F71808, F71858, F71862, F71869, F71869A, F71882, F71889, F81865 Datasheet references: F71808A: http://www.electronicsdatasheets.com/download/534cf560e34e2406135f4658.pdf?format=pdf F71858: http://www.electronicsdatasheets.com/download/534cf55fe34e2406135f4635.pdf?format=pdf F71862: http://www.hardwaresecrets.com/datasheets/F71862_V027P.pdf F71869: http://www.clubedohardware.com.br/datasheets/366451_F71869.pdf F71869A: http://www.chipset-ic.com/datasheet/F71869AD.pdf F71882: http://www.digchip.com/datasheets/parts/datasheet/931/F71882-pdf.php F71889: http://pdf1.alldatasheet.com/datasheet-pdf/view/406312/FINTEK/F71889.html F81865: http://www.hardwaresecrets.com/datasheets/F81865_V028P.pdf http://www.alldatasheet.com/datasheet-pdf/pdf/406317/FINTEK/F81865.html Signed-off-by: Knud Poulsen Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/f71808e_wdt.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/watchdog/f71808e_wdt.c b/drivers/watchdog/f71808e_wdt.c index c1e95bcdf911..d4ba262da7ba 100644 --- a/drivers/watchdog/f71808e_wdt.c +++ b/drivers/watchdog/f71808e_wdt.c @@ -67,7 +67,7 @@ #define F71808FG_FLAG_WDOUT_EN 7 -#define F71808FG_FLAG_WDTMOUT_STS 5 +#define F71808FG_FLAG_WDTMOUT_STS 6 #define F71808FG_FLAG_WD_EN 5 #define F71808FG_FLAG_WD_PULSE 4 #define F71808FG_FLAG_WD_UNIT 3 @@ -670,7 +670,7 @@ static int __init watchdog_init(int sioaddr) superio_select(watchdog.sioaddr, SIO_F71808FG_LD_WDT); wdt_conf = superio_inb(sioaddr, F71808FG_REG_WDT_CONF); - watchdog.caused_reboot = wdt_conf & F71808FG_FLAG_WDTMOUT_STS; + watchdog.caused_reboot = wdt_conf & BIT(F71808FG_FLAG_WDTMOUT_STS); superio_exit(sioaddr); From e26e74b15468b42c47cf9b045539720006abb1e4 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Tue, 26 Apr 2016 18:18:49 +0100 Subject: [PATCH 11/17] watchdog: remove error message when unable to allocate watchdog device The dev_err message is superfluous because the failure is already printed by dev_kzalloc, so remove it. Signed-off-by: Colin Ian King Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/jz4740_wdt.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/watchdog/jz4740_wdt.c b/drivers/watchdog/jz4740_wdt.c index 6a7d5c365438..c8d51ddb26d5 100644 --- a/drivers/watchdog/jz4740_wdt.c +++ b/drivers/watchdog/jz4740_wdt.c @@ -160,10 +160,8 @@ static int jz4740_wdt_probe(struct platform_device *pdev) drvdata = devm_kzalloc(&pdev->dev, sizeof(struct jz4740_wdt_drvdata), GFP_KERNEL); - if (!drvdata) { - dev_err(&pdev->dev, "Unable to alloacate watchdog device\n"); + if (!drvdata) return -ENOMEM; - } if (heartbeat < 1 || heartbeat > MAX_HEARTBEAT) heartbeat = DEFAULT_HEARTBEAT; From bd99b68ed7f96c9c845aad2a25f84145213058f2 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 1 Apr 2016 13:56:23 +0200 Subject: [PATCH 12/17] watchdog: renesas-wdt: add driver Add support for watchdogs (RWDT and SWDT) found on RCar Gen3 based SoCs from Renesas. Signed-off-by: Wolfram Sang Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- .../bindings/watchdog/renesas-wdt.txt | 25 ++ drivers/watchdog/Kconfig | 8 + drivers/watchdog/Makefile | 1 + drivers/watchdog/renesas_wdt.c | 213 ++++++++++++++++++ 4 files changed, 247 insertions(+) create mode 100644 Documentation/devicetree/bindings/watchdog/renesas-wdt.txt create mode 100644 drivers/watchdog/renesas_wdt.c diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt new file mode 100644 index 000000000000..b9512f1eb80a --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -0,0 +1,25 @@ +Renesas Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "renesas,r8a7795-wdt", or "renesas,rcar-gen3-wdt" + + When compatible with the generic version, nodes must list the SoC-specific + version corresponding to the platform first, followed by the generic + version. + +- reg : Should contain WDT registers location and length +- clocks : the clock feeding the watchdog timer. + +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds +- power-domains : the power domain the WDT belongs to + +Examples: + + wdt0: watchdog@e6020000 { + compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 402>; + power-domains = <&cpg>; + timeout-sec = <60>; + }; diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index fb947655badd..3902c9ca7f09 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -661,6 +661,14 @@ config ATLAS7_WATCHDOG To compile this driver as a module, choose M here: the module will be called atlas7_wdt. +config RENESAS_WDT + tristate "Renesas WDT Watchdog" + depends on ARCH_RENESAS || COMPILE_TEST + select WATCHDOG_CORE + help + This driver adds watchdog support for the integrated watchdogs in the + Renesas R-Car and other SH-Mobile SoCs (usually named RWDT or SWDT). + # AVR32 Architecture config AT32AP700X_WDT diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile index feb6270fdbde..2cbc9709852d 100644 --- a/drivers/watchdog/Makefile +++ b/drivers/watchdog/Makefile @@ -73,6 +73,7 @@ obj-$(CONFIG_DIGICOLOR_WATCHDOG) += digicolor_wdt.o obj-$(CONFIG_LPC18XX_WATCHDOG) += lpc18xx_wdt.o obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o +obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o # AVR32 Architecture obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o diff --git a/drivers/watchdog/renesas_wdt.c b/drivers/watchdog/renesas_wdt.c new file mode 100644 index 000000000000..cf61c92f7ecd --- /dev/null +++ b/drivers/watchdog/renesas_wdt.c @@ -0,0 +1,213 @@ +/* + * Watchdog driver for Renesas WDT watchdog + * + * Copyright (C) 2015-16 Wolfram Sang, Sang Engineering + * Copyright (C) 2015-16 Renesas Electronics Corporation + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define RWTCNT 0 +#define RWTCSRA 4 +#define RWTCSRA_WOVF BIT(4) +#define RWTCSRA_WRFLG BIT(5) +#define RWTCSRA_TME BIT(7) + +#define RWDT_DEFAULT_TIMEOUT 60U + +static const unsigned int clk_divs[] = { 1, 4, 16, 32, 64, 128, 1024 }; + +static bool nowayout = WATCHDOG_NOWAYOUT; +module_param(nowayout, bool, 0); +MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" + __MODULE_STRING(WATCHDOG_NOWAYOUT) ")"); + +struct rwdt_priv { + void __iomem *base; + struct watchdog_device wdev; + struct clk *clk; + unsigned int clks_per_sec; + u8 cks; +}; + +static void rwdt_write(struct rwdt_priv *priv, u32 val, unsigned int reg) +{ + if (reg == RWTCNT) + val |= 0x5a5a0000; + else + val |= 0xa5a5a500; + + writel_relaxed(val, priv->base + reg); +} + +static int rwdt_init_timeout(struct watchdog_device *wdev) +{ + struct rwdt_priv *priv = watchdog_get_drvdata(wdev); + + rwdt_write(priv, 65536 - wdev->timeout * priv->clks_per_sec, RWTCNT); + + return 0; +} + +static int rwdt_start(struct watchdog_device *wdev) +{ + struct rwdt_priv *priv = watchdog_get_drvdata(wdev); + + clk_prepare_enable(priv->clk); + + rwdt_write(priv, priv->cks, RWTCSRA); + rwdt_init_timeout(wdev); + + while (readb_relaxed(priv->base + RWTCSRA) & RWTCSRA_WRFLG) + cpu_relax(); + + rwdt_write(priv, priv->cks | RWTCSRA_TME, RWTCSRA); + + return 0; +} + +static int rwdt_stop(struct watchdog_device *wdev) +{ + struct rwdt_priv *priv = watchdog_get_drvdata(wdev); + + rwdt_write(priv, priv->cks, RWTCSRA); + clk_disable_unprepare(priv->clk); + + return 0; +} + +static unsigned int rwdt_get_timeleft(struct watchdog_device *wdev) +{ + struct rwdt_priv *priv = watchdog_get_drvdata(wdev); + u16 val = readw_relaxed(priv->base + RWTCNT); + + return DIV_ROUND_CLOSEST(65536 - val, priv->clks_per_sec); +} + +static const struct watchdog_info rwdt_ident = { + .options = WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT, + .identity = "Renesas WDT Watchdog", +}; + +static const struct watchdog_ops rwdt_ops = { + .owner = THIS_MODULE, + .start = rwdt_start, + .stop = rwdt_stop, + .ping = rwdt_init_timeout, + .get_timeleft = rwdt_get_timeleft, +}; + +static int rwdt_probe(struct platform_device *pdev) +{ + struct rwdt_priv *priv; + struct resource *res; + unsigned long rate; + unsigned int clks_per_sec; + int ret, i; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + rate = clk_get_rate(priv->clk); + if (!rate) + return -ENOENT; + + for (i = ARRAY_SIZE(clk_divs) - 1; i >= 0; i--) { + clks_per_sec = DIV_ROUND_UP(rate, clk_divs[i]); + if (clks_per_sec) { + priv->clks_per_sec = clks_per_sec; + priv->cks = i; + break; + } + } + + if (!clks_per_sec) { + dev_err(&pdev->dev, "Can't find suitable clock divider\n"); + return -ERANGE; + } + + pm_runtime_enable(&pdev->dev); + pm_runtime_get_sync(&pdev->dev); + + priv->wdev.info = &rwdt_ident, + priv->wdev.ops = &rwdt_ops, + priv->wdev.parent = &pdev->dev; + priv->wdev.min_timeout = 1; + priv->wdev.max_timeout = 65536 / clks_per_sec; + priv->wdev.timeout = min(priv->wdev.max_timeout, RWDT_DEFAULT_TIMEOUT); + + platform_set_drvdata(pdev, priv); + watchdog_set_drvdata(&priv->wdev, priv); + watchdog_set_nowayout(&priv->wdev, nowayout); + + /* This overrides the default timeout only if DT configuration was found */ + ret = watchdog_init_timeout(&priv->wdev, 0, &pdev->dev); + if (ret) + dev_warn(&pdev->dev, "Specified timeout value invalid, using default\n"); + + ret = watchdog_register_device(&priv->wdev); + if (ret < 0) { + pm_runtime_put(&pdev->dev); + pm_runtime_disable(&pdev->dev); + return ret; + } + + return 0; +} + +static int rwdt_remove(struct platform_device *pdev) +{ + struct rwdt_priv *priv = platform_get_drvdata(pdev); + + watchdog_unregister_device(&priv->wdev); + pm_runtime_put(&pdev->dev); + pm_runtime_disable(&pdev->dev); + + return 0; +} + +/* + * This driver does also fit for R-Car Gen2 (r8a779[0-4]) WDT. However, for SMP + * to work there, one also needs a RESET (RST) driver which does not exist yet + * due to HW issues. This needs to be solved before adding compatibles here. + */ +static const struct of_device_id rwdt_ids[] = { + { .compatible = "renesas,rcar-gen3-wdt", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, rwdt_ids); + +static struct platform_driver rwdt_driver = { + .driver = { + .name = "renesas_wdt", + .of_match_table = rwdt_ids, + }, + .probe = rwdt_probe, + .remove = rwdt_remove, +}; +module_platform_driver(rwdt_driver); + +MODULE_DESCRIPTION("Renesas WDT Watchdog Driver"); +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Wolfram Sang "); From fc4d2c7390dde766ec62f8f83be06e9227e9eb7a Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 1 Apr 2016 13:56:26 +0200 Subject: [PATCH 13/17] arm64: defconfig: enable Renesas Watchdog Timer Signed-off-by: Wolfram Sang Reviewed-by: Geert Uytterhoeven Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- arch/arm64/configs/defconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index a44ef995d8ae..2578d55e336c 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -171,6 +171,8 @@ CONFIG_POWER_RESET_SYSCON=y CONFIG_THERMAL=y CONFIG_THERMAL_EMULATION=y CONFIG_EXYNOS_THERMAL=y +CONFIG_WATCHDOG=y +CONFIG_RENESAS_WDT=y CONFIG_MFD_SPMI_PMIC=y CONFIG_MFD_SEC_CORE=y CONFIG_REGULATOR=y From d904ac34bdbcf62a50c745cfe991681ae3948e4e Mon Sep 17 00:00:00 2001 From: Muhammad Falak R Wani Date: Fri, 6 May 2016 18:29:40 +0530 Subject: [PATCH 14/17] watchdog: cpwd: Use setup_timer() The function setup_timer combines the initialization of a timer with the initialization of the timer's function and data fields. The multiline code for timer initialization is now replaced with function setup_timer. Signed-off-by: Muhammad Falak R Wani Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/cpwd.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/watchdog/cpwd.c b/drivers/watchdog/cpwd.c index 02007689e9ca..71ee07950e63 100644 --- a/drivers/watchdog/cpwd.c +++ b/drivers/watchdog/cpwd.c @@ -611,9 +611,7 @@ static int cpwd_probe(struct platform_device *op) } if (p->broken) { - init_timer(&cpwd_timer); - cpwd_timer.function = cpwd_brokentimer; - cpwd_timer.data = (unsigned long) p; + setup_timer(&cpwd_timer, cpwd_brokentimer, (unsigned long)p); cpwd_timer.expires = WD_BTIMEOUT; pr_info("PLD defect workaround enabled for model %s\n", From 12fe36e2ca0e474a2d7b48ab018d16977f9745a4 Mon Sep 17 00:00:00 2001 From: Muhammad Falak R Wani Date: Fri, 6 May 2016 18:29:41 +0530 Subject: [PATCH 15/17] watchdog: shwdt: Use setup_timer() The function setup_timer combines the initialization of a timer with the initialization of the timer's function and data fields. The multiline code for timer initialization is now replaced with function setup_timer. Signed-off-by: Muhammad Falak R Wani Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- drivers/watchdog/shwdt.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/watchdog/shwdt.c b/drivers/watchdog/shwdt.c index f90812170657..517a733175ef 100644 --- a/drivers/watchdog/shwdt.c +++ b/drivers/watchdog/shwdt.c @@ -275,9 +275,7 @@ static int sh_wdt_probe(struct platform_device *pdev) return rc; } - init_timer(&wdt->timer); - wdt->timer.function = sh_wdt_ping; - wdt->timer.data = (unsigned long)wdt; + setup_timer(&wdt->timer, sh_wdt_ping, (unsigned long)wdt); wdt->timer.expires = next_ping_period(clock_division_ratio); dev_info(&pdev->dev, "initialized.\n"); From ae67643edc6edcab41d8d5d35cb796416b253a01 Mon Sep 17 00:00:00 2001 From: William Breathitt Gray Date: Wed, 11 May 2016 08:47:46 -0400 Subject: [PATCH 16/17] Documentation: Add ebc-c384_wdt watchdog-parameters.txt entry The WinSystems EBC-C384 watchdog timer driver supports two module parameters: timeout and nowayout. These parameters should be documented in the watchdog-parameters.txt file. Signed-off-by: William Breathitt Gray Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- Documentation/watchdog/watchdog-parameters.txt | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt index c161399a6b5c..a8d364227a77 100644 --- a/Documentation/watchdog/watchdog-parameters.txt +++ b/Documentation/watchdog/watchdog-parameters.txt @@ -86,6 +86,10 @@ nowayout: Watchdog cannot be stopped once started davinci_wdt: heartbeat: Watchdog heartbeat period in seconds from 1 to 600, default 60 ------------------------------------------------- +ebc-c384_wdt: +timeout: Watchdog timeout in seconds. (1<=timeout<=15300, default=60) +nowayout: Watchdog cannot be stopped once started +------------------------------------------------- ep93xx_wdt: nowayout: Watchdog cannot be stopped once started timeout: Watchdog timeout in seconds. (1<=timeout<=3600, default=TBD) From 540be8b2add1a18a4289b11c1a9b6956eb846630 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Sun, 22 May 2016 11:06:29 +0200 Subject: [PATCH 17/17] MAINTAINERS: Add file patterns for watchdog device tree bindings Submitters of device tree binding documentation may forget to CC the subsystem maintainer if this is missing. Signed-off-by: Geert Uytterhoeven Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck Cc: linux-watchdog@vger.kernel.org --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index a727d9959ecd..f69706d7fafd 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -12073,6 +12073,7 @@ L: linux-watchdog@vger.kernel.org W: http://www.linux-watchdog.org/ T: git git://www.linux-watchdog.org/linux-watchdog.git S: Maintained +F: Documentation/devicetree/bindings/watchdog/ F: Documentation/watchdog/ F: drivers/watchdog/ F: include/linux/watchdog.h