From f7519d8c8290765a9408a52db4ba4a368ff72ca5 Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 22:54:18 +0100 Subject: [PATCH 01/82] ARM: OMAP1: ams-delta: register latch dependent devices later In preparation to converting Amstrad Delta on-board latches to basic_mmio_gpio devices, registration of platform devices which depend on latches and will require initialization of their GPIO pins first, should be moved out of .machine_init down to late_initcall level, as the gpio-generic driver is not available until device_initcall time. The latch reset operation, which will be replaced with GPIO initialization, must also be moved to late_initcall for the same reason. Since there was already another, separate arch_initcall function for setting up one of those latch dependent devices, the on-board modem device, reuse that function, i.e., rename it to a name that matches the new purpose, extend with other device setup relocated from .machine_init, and move down to the late_initcall level. While being at it, add missing gpio_free() in case the modem platform device registration fails. Thanks to Tony Lindgren who suggested this approach instead of shifting up the gpio-generic driver initialization. In addition, defer registration of the Amstrad Delta ASoC and serio devices, done from their device driver files, until late_initcall time, as those drivers will depend on their GPIO pins already requested from the board late_init() function until updated to register their GPIO pins themselves. Signed-off-by: Janusz Krzysztofik Acked-by: Mark Brown Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/board-ams-delta.c | 28 +++++++++++++++++++-------- drivers/input/serio/ams_delta_serio.c | 2 +- sound/soc/omap/ams-delta.c | 2 +- 3 files changed, 22 insertions(+), 10 deletions(-) diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index b0f15d234a12..50987c91690f 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -275,11 +275,14 @@ static struct omap1_cam_platform_data ams_delta_camera_platform_data = { }; static struct platform_device *ams_delta_devices[] __initdata = { - &ams_delta_nand_device, &ams_delta_kp_device, + &ams_delta_camera_device, +}; + +static struct platform_device *late_devices[] __initdata = { + &ams_delta_nand_device, &ams_delta_lcd_device, &ams_delta_led_device, - &ams_delta_camera_device, }; static void __init ams_delta_init(void) @@ -307,9 +310,6 @@ static void __init ams_delta_init(void) omap_serial_init(); omap_register_i2c_bus(1, 100, NULL, 0); - /* Clear latch2 (NAND, LCD, modem enable) */ - ams_delta_latch2_write(~0, 0); - omap1_usb_init(&ams_delta_usb_config); omap1_set_camera_info(&ams_delta_camera_platform_data); #ifdef CONFIG_LEDS_TRIGGERS @@ -345,13 +345,18 @@ static struct platform_device ams_delta_modem_device = { }, }; -static int __init ams_delta_modem_init(void) +static int __init late_init(void) { int err; if (!machine_is_ams_delta()) return -ENODEV; + /* Clear latch2 (NAND, LCD, modem enable) */ + ams_delta_latch2_write(~0, 0); + + platform_add_devices(late_devices, ARRAY_SIZE(late_devices)); + omap_cfg_reg(M14_1510_GPIO2); ams_delta_modem_ports[0].irq = gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ); @@ -367,9 +372,16 @@ static int __init ams_delta_modem_init(void) AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC, AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC); - return platform_device_register(&ams_delta_modem_device); + err = platform_device_register(&ams_delta_modem_device); + if (err) + goto gpio_free; + return 0; + +gpio_free: + gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ); + return err; } -arch_initcall(ams_delta_modem_init); +late_initcall(late_init); static void __init ams_delta_map_io(void) { diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c index d4d08bd9205b..835d37abe62a 100644 --- a/drivers/input/serio/ams_delta_serio.c +++ b/drivers/input/serio/ams_delta_serio.c @@ -165,7 +165,7 @@ serio: kfree(ams_delta_serio); return err; } -module_init(ams_delta_serio_init); +late_initcall(ams_delta_serio_init); static void __exit ams_delta_serio_exit(void) { diff --git a/sound/soc/omap/ams-delta.c b/sound/soc/omap/ams-delta.c index ccb8a6aa1817..be81bc791b11 100644 --- a/sound/soc/omap/ams-delta.c +++ b/sound/soc/omap/ams-delta.c @@ -636,7 +636,7 @@ err: platform_device_put(ams_delta_audio_platform_device); return ret; } -module_init(ams_delta_module_init); +late_initcall(ams_delta_module_init); static void __exit ams_delta_module_exit(void) { From 937eb4bb00588571f223eade260f9b509bf223ab Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 03:24:21 +0100 Subject: [PATCH 02/82] ARM: OMAP1: ams-delta: convert latches to basic_mmio_gpio Once ready, ams-delta specific device drivers currently calling custom ams_delta_latch[12]_write() functions can be updated to call generic gpio_set_value() instead, which will make them less platform dependent. Even more, some custom ams-delta only drivers can perhaps be dropped from the tree after converting selected ams-delta platform devices to follow generic GPIO based device models. The latch_gpios[] table is initially filled with all latch1 and latch2 GPIO pins in order to register and initialize them from the board file until those are handled by respective existing device drivers (leds, nand, lcd, serio, asoc, serial). That table will get almost empty after the transision process is completed, holding only pins not used by any drivers / connected to unused devices, in order to initialize them from the board file for power saving purposes. The new ams_delta_latch_write() function is a unified replacement for those removed ams_delta_latch[12]_write(), and serves as a temporary wrapper over gpio_set_value(), providing the old API for those not yet updated device drivers, and will be removed after all custom drivers are converted or replaced. Signed-off-by: Janusz Krzysztofik Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/Kconfig | 1 + arch/arm/mach-omap1/board-ams-delta.c | 237 +++++++++++++++--- .../plat-omap/include/plat/board-ams-delta.h | 43 +++- 3 files changed, 242 insertions(+), 39 deletions(-) diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig index 4f8d66f044e7..e14532f236a0 100644 --- a/arch/arm/mach-omap1/Kconfig +++ b/arch/arm/mach-omap1/Kconfig @@ -155,6 +155,7 @@ config MACH_AMS_DELTA bool "Amstrad E3 (Delta)" depends on ARCH_OMAP1 && ARCH_OMAP15XX select FIQ + select GPIO_GENERIC_PLATFORM help Support for the Amstrad E3 (codename Delta) videophone. Say Y here if you have such a device. diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index 50987c91690f..cff2711dc259 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -11,6 +11,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ +#include #include #include #include @@ -40,9 +41,6 @@ #include -static u8 ams_delta_latch1_reg; -static u16 ams_delta_latch2_reg; - static const unsigned int ams_delta_keymap[] = { KEY(0, 0, KEY_F1), /* Advert */ @@ -121,39 +119,32 @@ static const unsigned int ams_delta_keymap[] = { KEY(7, 3, KEY_LEFTCTRL), /* Vol down */ }; -void ams_delta_latch1_write(u8 mask, u8 value) -{ - ams_delta_latch1_reg &= ~mask; - ams_delta_latch1_reg |= value; - *(volatile __u8 *) AMS_DELTA_LATCH1_VIRT = ams_delta_latch1_reg; -} - -void ams_delta_latch2_write(u16 mask, u16 value) -{ - ams_delta_latch2_reg &= ~mask; - ams_delta_latch2_reg |= value; - *(volatile __u16 *) AMS_DELTA_LATCH2_VIRT = ams_delta_latch2_reg; -} +#define LATCH1_PHYS 0x01000000 +#define LATCH1_VIRT 0xEA000000 +#define MODEM_PHYS 0x04000000 +#define MODEM_VIRT 0xEB000000 +#define LATCH2_PHYS 0x08000000 +#define LATCH2_VIRT 0xEC000000 static struct map_desc ams_delta_io_desc[] __initdata = { /* AMS_DELTA_LATCH1 */ { - .virtual = AMS_DELTA_LATCH1_VIRT, - .pfn = __phys_to_pfn(AMS_DELTA_LATCH1_PHYS), + .virtual = LATCH1_VIRT, + .pfn = __phys_to_pfn(LATCH1_PHYS), .length = 0x01000000, .type = MT_DEVICE }, /* AMS_DELTA_LATCH2 */ { - .virtual = AMS_DELTA_LATCH2_VIRT, - .pfn = __phys_to_pfn(AMS_DELTA_LATCH2_PHYS), + .virtual = LATCH2_VIRT, + .pfn = __phys_to_pfn(LATCH2_PHYS), .length = 0x01000000, .type = MT_DEVICE }, /* AMS_DELTA_MODEM */ { - .virtual = AMS_DELTA_MODEM_VIRT, - .pfn = __phys_to_pfn(AMS_DELTA_MODEM_PHYS), + .virtual = MODEM_VIRT, + .pfn = __phys_to_pfn(MODEM_PHYS), .length = 0x01000000, .type = MT_DEVICE } @@ -173,6 +164,190 @@ static struct omap_board_config_kernel ams_delta_config[] __initdata = { { OMAP_TAG_LCD, &ams_delta_lcd_config }, }; +static struct resource latch1_resources[] __initconst = { + [0] = { + .name = "dat", + .start = LATCH1_PHYS, + .end = LATCH1_PHYS + (AMS_DELTA_LATCH1_NGPIO - 1) / 8, + .flags = IORESOURCE_MEM, + }, +}; + +static struct bgpio_pdata latch1_pdata __initconst = { + .base = AMS_DELTA_LATCH1_GPIO_BASE, + .ngpio = AMS_DELTA_LATCH1_NGPIO, +}; + +static struct platform_device latch1_gpio_device = { + .name = "basic-mmio-gpio", + .id = 0, + .resource = latch1_resources, + .num_resources = ARRAY_SIZE(latch1_resources), + .dev = { + .platform_data = &latch1_pdata, + }, +}; + +static struct resource latch2_resources[] __initconst = { + [0] = { + .name = "dat", + .start = LATCH2_PHYS, + .end = LATCH2_PHYS + (AMS_DELTA_LATCH2_NGPIO - 1) / 8, + .flags = IORESOURCE_MEM, + }, +}; + +static struct bgpio_pdata latch2_pdata __initconst = { + .base = AMS_DELTA_LATCH2_GPIO_BASE, + .ngpio = AMS_DELTA_LATCH2_NGPIO, +}; + +static struct platform_device latch2_gpio_device = { + .name = "basic-mmio-gpio", + .id = 1, + .resource = latch2_resources, + .num_resources = ARRAY_SIZE(latch2_resources), + .dev = { + .platform_data = &latch2_pdata, + }, +}; + +static struct gpio latch_gpios[] __initconst = { + { + .gpio = AMS_DELTA_GPIO_PIN_LED_CAMERA, + .flags = GPIOF_OUT_INIT_LOW, + .label = "led_camera", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LED_ADVERT, + .flags = GPIOF_OUT_INIT_LOW, + .label = "led_advert", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LED_EMAIL, + .flags = GPIOF_OUT_INIT_LOW, + .label = "led_email", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LED_HANDSFREE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "led_handsfree", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LED_VOICEMAIL, + .flags = GPIOF_OUT_INIT_LOW, + .label = "led_voicemail", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LED_VOICE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "led_voice", + }, + { + .gpio = AMS_DELTA_LATCH1_GPIO_BASE + 6, + .flags = GPIOF_OUT_INIT_LOW, + .label = "dockit1", + }, + { + .gpio = AMS_DELTA_LATCH1_GPIO_BASE + 7, + .flags = GPIOF_OUT_INIT_LOW, + .label = "dockit2", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LCD_VBLEN, + .flags = GPIOF_OUT_INIT_LOW, + .label = "lcd_vblen", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LCD_NDISP, + .flags = GPIOF_OUT_INIT_LOW, + .label = "lcd_ndisp", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NCE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_nce", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NRE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_nre", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NWP, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_nwp", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NWE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_nwe", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_ALE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_ale", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_CLE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_cle", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR, + .flags = GPIOF_OUT_INIT_LOW, + .label = "keybrd_pwr", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT, + .flags = GPIOF_OUT_INIT_LOW, + .label = "keybrd_dataout", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_SCARD_RSTIN, + .flags = GPIOF_OUT_INIT_LOW, + .label = "scard_rstin", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_SCARD_CMDVCC, + .flags = GPIOF_OUT_INIT_LOW, + .label = "scard_cmdvcc", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET, + .flags = GPIOF_OUT_INIT_LOW, + .label = "modem_nreset", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC, + .flags = GPIOF_OUT_INIT_LOW, + .label = "modem_codec", + }, + { + .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 14, + .flags = GPIOF_OUT_INIT_LOW, + .label = "hookflash1", + }, + { + .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 15, + .flags = GPIOF_OUT_INIT_LOW, + .label = "hookflash2", + }, +}; + +void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value) +{ + int bit = 0; + u16 bitpos = 1 << bit; + + for (; bit < ngpio; bit++, bitpos = bitpos << 1) { + if (!(mask & bitpos)) + continue; + gpio_set_value(base + bit, (value & bitpos) != 0); + } +} +EXPORT_SYMBOL(ams_delta_latch_write); + static struct resource ams_delta_nand_resources[] = { [0] = { .start = OMAP1_MPUIO_BASE, @@ -275,11 +450,13 @@ static struct omap1_cam_platform_data ams_delta_camera_platform_data = { }; static struct platform_device *ams_delta_devices[] __initdata = { + &latch1_gpio_device, + &latch2_gpio_device, &ams_delta_kp_device, &ams_delta_camera_device, }; -static struct platform_device *late_devices[] __initdata = { +static struct platform_device *late_devices[] __initconst = { &ams_delta_nand_device, &ams_delta_lcd_device, &ams_delta_led_device, @@ -325,8 +502,8 @@ static void __init ams_delta_init(void) static struct plat_serial8250_port ams_delta_modem_ports[] = { { - .membase = IOMEM(AMS_DELTA_MODEM_VIRT), - .mapbase = AMS_DELTA_MODEM_PHYS, + .membase = IOMEM(MODEM_VIRT), + .mapbase = MODEM_PHYS, .irq = -EINVAL, /* changed later */ .flags = UPF_BOOT_AUTOCONF, .irqflags = IRQF_TRIGGER_RISING, @@ -352,8 +529,11 @@ static int __init late_init(void) if (!machine_is_ams_delta()) return -ENODEV; - /* Clear latch2 (NAND, LCD, modem enable) */ - ams_delta_latch2_write(~0, 0); + err = gpio_request_array(latch_gpios, ARRAY_SIZE(latch_gpios)); + if (err) { + pr_err("Couldn't take over latch1/latch2 GPIO pins\n"); + return err; + } platform_add_devices(late_devices, ARRAY_SIZE(late_devices)); @@ -399,6 +579,3 @@ MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)") .init_machine = ams_delta_init, .timer = &omap1_timer, MACHINE_END - -EXPORT_SYMBOL(ams_delta_latch1_write); -EXPORT_SYMBOL(ams_delta_latch2_write); diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h index 51b102dc906b..68ffe328a777 100644 --- a/arch/arm/plat-omap/include/plat/board-ams-delta.h +++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h @@ -28,13 +28,6 @@ #if defined (CONFIG_MACH_AMS_DELTA) -#define AMS_DELTA_LATCH1_PHYS 0x01000000 -#define AMS_DELTA_LATCH1_VIRT 0xEA000000 -#define AMS_DELTA_MODEM_PHYS 0x04000000 -#define AMS_DELTA_MODEM_VIRT 0xEB000000 -#define AMS_DELTA_LATCH2_PHYS 0x08000000 -#define AMS_DELTA_LATCH2_VIRT 0xEC000000 - #define AMS_DELTA_LATCH1_LED_CAMERA 0x01 #define AMS_DELTA_LATCH1_LED_ADVERT 0x02 #define AMS_DELTA_LATCH1_LED_EMAIL 0x04 @@ -66,9 +59,41 @@ #define AMS_DELTA_GPIO_PIN_CONFIG 11 #define AMS_DELTA_GPIO_PIN_NAND_RB 12 +#define AMS_DELTA_GPIO_PIN_LED_CAMERA 232 +#define AMS_DELTA_GPIO_PIN_LED_ADVERT 233 +#define AMS_DELTA_GPIO_PIN_LED_EMAIL 234 +#define AMS_DELTA_GPIO_PIN_LED_HANDSFREE 235 +#define AMS_DELTA_GPIO_PIN_LED_VOICEMAIL 236 +#define AMS_DELTA_GPIO_PIN_LED_VOICE 237 + +#define AMS_DELTA_GPIO_PIN_LCD_VBLEN 240 +#define AMS_DELTA_GPIO_PIN_LCD_NDISP 241 +#define AMS_DELTA_GPIO_PIN_NAND_NCE 242 +#define AMS_DELTA_GPIO_PIN_NAND_NRE 243 +#define AMS_DELTA_GPIO_PIN_NAND_NWP 244 +#define AMS_DELTA_GPIO_PIN_NAND_NWE 245 +#define AMS_DELTA_GPIO_PIN_NAND_ALE 246 +#define AMS_DELTA_GPIO_PIN_NAND_CLE 247 +#define AMS_DELTA_GPIO_PIN_KEYBRD_PWR 248 +#define AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT 249 +#define AMS_DELTA_GPIO_PIN_SCARD_RSTIN 250 +#define AMS_DELTA_GPIO_PIN_SCARD_CMDVCC 251 +#define AMS_DELTA_GPIO_PIN_MODEM_NRESET 252 +#define AMS_DELTA_GPIO_PIN_MODEM_CODEC 253 + +#define AMS_DELTA_LATCH1_GPIO_BASE AMS_DELTA_GPIO_PIN_LED_CAMERA +#define AMS_DELTA_LATCH1_NGPIO 8 +#define AMS_DELTA_LATCH2_GPIO_BASE AMS_DELTA_GPIO_PIN_LCD_VBLEN +#define AMS_DELTA_LATCH2_NGPIO 16 + #ifndef __ASSEMBLY__ -void ams_delta_latch1_write(u8 mask, u8 value); -void ams_delta_latch2_write(u16 mask, u16 value); +void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value); +#define ams_delta_latch1_write(mask, value) \ + ams_delta_latch_write(AMS_DELTA_LATCH1_GPIO_BASE, \ + AMS_DELTA_LATCH1_NGPIO, (mask), (value)) +#define ams_delta_latch2_write(mask, value) \ + ams_delta_latch_write(AMS_DELTA_LATCH2_GPIO_BASE, \ + AMS_DELTA_LATCH2_NGPIO, (mask), (value)) #endif #endif /* CONFIG_MACH_AMS_DELTA */ From 5ca6180fa6d7333fb5fabf30420b0e3cc32dd731 Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 00:08:53 +0100 Subject: [PATCH 03/82] ARM: OMAP1: ams-delta: supersede custom led device by leds-gpio Now that the Amstrad Delta on-board latches have been converted to GPIO devices, use the generic driver to control on-board LEDs which hang off those latches. Signed-off-by: Janusz Krzysztofik Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/Kconfig | 1 + arch/arm/mach-omap1/board-ams-delta.c | 87 ++++++++++--------- .../plat-omap/include/plat/board-ams-delta.h | 19 ---- 3 files changed, 49 insertions(+), 58 deletions(-) diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig index e14532f236a0..5b1edbae6893 100644 --- a/arch/arm/mach-omap1/Kconfig +++ b/arch/arm/mach-omap1/Kconfig @@ -156,6 +156,7 @@ config MACH_AMS_DELTA depends on ARCH_OMAP1 && ARCH_OMAP15XX select FIQ select GPIO_GENERIC_PLATFORM + select LEDS_GPIO_REGISTER help Support for the Amstrad E3 (codename Delta) videophone. Say Y here if you have such a device. diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index cff2711dc259..034d0094e93a 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -164,18 +164,21 @@ static struct omap_board_config_kernel ams_delta_config[] __initdata = { { OMAP_TAG_LCD, &ams_delta_lcd_config }, }; +#define LATCH1_GPIO_BASE 232 +#define LATCH1_NGPIO 8 + static struct resource latch1_resources[] __initconst = { [0] = { .name = "dat", .start = LATCH1_PHYS, - .end = LATCH1_PHYS + (AMS_DELTA_LATCH1_NGPIO - 1) / 8, + .end = LATCH1_PHYS + (LATCH1_NGPIO - 1) / 8, .flags = IORESOURCE_MEM, }, }; static struct bgpio_pdata latch1_pdata __initconst = { - .base = AMS_DELTA_LATCH1_GPIO_BASE, - .ngpio = AMS_DELTA_LATCH1_NGPIO, + .base = LATCH1_GPIO_BASE, + .ngpio = LATCH1_NGPIO, }; static struct platform_device latch1_gpio_device = { @@ -214,42 +217,12 @@ static struct platform_device latch2_gpio_device = { static struct gpio latch_gpios[] __initconst = { { - .gpio = AMS_DELTA_GPIO_PIN_LED_CAMERA, - .flags = GPIOF_OUT_INIT_LOW, - .label = "led_camera", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_LED_ADVERT, - .flags = GPIOF_OUT_INIT_LOW, - .label = "led_advert", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_LED_EMAIL, - .flags = GPIOF_OUT_INIT_LOW, - .label = "led_email", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_LED_HANDSFREE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "led_handsfree", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_LED_VOICEMAIL, - .flags = GPIOF_OUT_INIT_LOW, - .label = "led_voicemail", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_LED_VOICE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "led_voice", - }, - { - .gpio = AMS_DELTA_LATCH1_GPIO_BASE + 6, + .gpio = LATCH1_GPIO_BASE + 6, .flags = GPIOF_OUT_INIT_LOW, .label = "dockit1", }, { - .gpio = AMS_DELTA_LATCH1_GPIO_BASE + 7, + .gpio = LATCH1_GPIO_BASE + 7, .flags = GPIOF_OUT_INIT_LOW, .label = "dockit2", }, @@ -399,9 +372,45 @@ static struct platform_device ams_delta_lcd_device = { .id = -1, }; -static struct platform_device ams_delta_led_device = { - .name = "ams-delta-led", - .id = -1 +static struct gpio_led gpio_leds[] __initconst = { + { + .name = "camera", + .gpio = LATCH1_GPIO_BASE + 0, + .default_state = LEDS_GPIO_DEFSTATE_OFF, +#ifdef CONFIG_LEDS_TRIGGERS + .default_trigger = "ams_delta_camera", +#endif + }, + { + .name = "advert", + .gpio = LATCH1_GPIO_BASE + 1, + .default_state = LEDS_GPIO_DEFSTATE_OFF, + }, + { + .name = "email", + .gpio = LATCH1_GPIO_BASE + 2, + .default_state = LEDS_GPIO_DEFSTATE_OFF, + }, + { + .name = "handsfree", + .gpio = LATCH1_GPIO_BASE + 3, + .default_state = LEDS_GPIO_DEFSTATE_OFF, + }, + { + .name = "voicemail", + .gpio = LATCH1_GPIO_BASE + 4, + .default_state = LEDS_GPIO_DEFSTATE_OFF, + }, + { + .name = "voice", + .gpio = LATCH1_GPIO_BASE + 5, + .default_state = LEDS_GPIO_DEFSTATE_OFF, + }, +}; + +static struct gpio_led_platform_data leds_pdata __initconst = { + .leds = gpio_leds, + .num_leds = ARRAY_SIZE(gpio_leds), }; static struct i2c_board_info ams_delta_camera_board_info[] = { @@ -459,7 +468,6 @@ static struct platform_device *ams_delta_devices[] __initdata = { static struct platform_device *late_devices[] __initconst = { &ams_delta_nand_device, &ams_delta_lcd_device, - &ams_delta_led_device, }; static void __init ams_delta_init(void) @@ -493,6 +501,7 @@ static void __init ams_delta_init(void) led_trigger_register_simple("ams_delta_camera", &ams_delta_camera_led_trigger); #endif + gpio_led_register_device(-1, &leds_pdata); platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices)); ams_delta_init_fiq(); diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h index 68ffe328a777..a0f86ca75ddc 100644 --- a/arch/arm/plat-omap/include/plat/board-ams-delta.h +++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h @@ -28,13 +28,6 @@ #if defined (CONFIG_MACH_AMS_DELTA) -#define AMS_DELTA_LATCH1_LED_CAMERA 0x01 -#define AMS_DELTA_LATCH1_LED_ADVERT 0x02 -#define AMS_DELTA_LATCH1_LED_EMAIL 0x04 -#define AMS_DELTA_LATCH1_LED_HANDSFREE 0x08 -#define AMS_DELTA_LATCH1_LED_VOICEMAIL 0x10 -#define AMS_DELTA_LATCH1_LED_VOICE 0x20 - #define AMS_DELTA_LATCH2_LCD_VBLEN 0x0001 #define AMS_DELTA_LATCH2_LCD_NDISP 0x0002 #define AMS_DELTA_LATCH2_NAND_NCE 0x0004 @@ -59,13 +52,6 @@ #define AMS_DELTA_GPIO_PIN_CONFIG 11 #define AMS_DELTA_GPIO_PIN_NAND_RB 12 -#define AMS_DELTA_GPIO_PIN_LED_CAMERA 232 -#define AMS_DELTA_GPIO_PIN_LED_ADVERT 233 -#define AMS_DELTA_GPIO_PIN_LED_EMAIL 234 -#define AMS_DELTA_GPIO_PIN_LED_HANDSFREE 235 -#define AMS_DELTA_GPIO_PIN_LED_VOICEMAIL 236 -#define AMS_DELTA_GPIO_PIN_LED_VOICE 237 - #define AMS_DELTA_GPIO_PIN_LCD_VBLEN 240 #define AMS_DELTA_GPIO_PIN_LCD_NDISP 241 #define AMS_DELTA_GPIO_PIN_NAND_NCE 242 @@ -81,16 +67,11 @@ #define AMS_DELTA_GPIO_PIN_MODEM_NRESET 252 #define AMS_DELTA_GPIO_PIN_MODEM_CODEC 253 -#define AMS_DELTA_LATCH1_GPIO_BASE AMS_DELTA_GPIO_PIN_LED_CAMERA -#define AMS_DELTA_LATCH1_NGPIO 8 #define AMS_DELTA_LATCH2_GPIO_BASE AMS_DELTA_GPIO_PIN_LCD_VBLEN #define AMS_DELTA_LATCH2_NGPIO 16 #ifndef __ASSEMBLY__ void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value); -#define ams_delta_latch1_write(mask, value) \ - ams_delta_latch_write(AMS_DELTA_LATCH1_GPIO_BASE, \ - AMS_DELTA_LATCH1_NGPIO, (mask), (value)) #define ams_delta_latch2_write(mask, value) \ ams_delta_latch_write(AMS_DELTA_LATCH2_GPIO_BASE, \ AMS_DELTA_LATCH2_NGPIO, (mask), (value)) From f6fc8a6a1a08e520ae58b9abd54152aa101af14a Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 00:08:54 +0100 Subject: [PATCH 04/82] LED: drop leds-ams-delta driver This driver is no longer needed after the Amstrad Delta on-board LED devices have been converted to leds-gpio compatible. Signed-off-by: Janusz Krzysztofik Cc: Richard Purdie Signed-off-by: Tony Lindgren --- drivers/leds/Kconfig | 7 -- drivers/leds/Makefile | 1 - drivers/leds/leds-ams-delta.c | 137 ---------------------------------- 3 files changed, 145 deletions(-) delete mode 100644 drivers/leds/leds-ams-delta.c diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index ff203a421863..352374630c17 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -74,13 +74,6 @@ config LEDS_S3C24XX This option enables support for LEDs connected to GPIO lines on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440. -config LEDS_AMS_DELTA - tristate "LED Support for the Amstrad Delta (E3)" - depends on LEDS_CLASS - depends on MACH_AMS_DELTA - help - This option enables support for the LEDs on Amstrad Delta (E3). - config LEDS_NET48XX tristate "LED Support for Soekris net48xx series Error LED" depends on LEDS_CLASS diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile index e4f6bf568880..f2b75b2c2ee9 100644 --- a/drivers/leds/Makefile +++ b/drivers/leds/Makefile @@ -12,7 +12,6 @@ obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o obj-$(CONFIG_LEDS_LM3530) += leds-lm3530.o obj-$(CONFIG_LEDS_MIKROTIK_RB532) += leds-rb532.o obj-$(CONFIG_LEDS_S3C24XX) += leds-s3c24xx.o -obj-$(CONFIG_LEDS_AMS_DELTA) += leds-ams-delta.o obj-$(CONFIG_LEDS_NET48XX) += leds-net48xx.o obj-$(CONFIG_LEDS_NET5501) += leds-net5501.o obj-$(CONFIG_LEDS_WRAP) += leds-wrap.o diff --git a/drivers/leds/leds-ams-delta.c b/drivers/leds/leds-ams-delta.c deleted file mode 100644 index 8c00937bf7e7..000000000000 --- a/drivers/leds/leds-ams-delta.c +++ /dev/null @@ -1,137 +0,0 @@ -/* - * LEDs driver for Amstrad Delta (E3) - * - * Copyright (C) 2006 Jonathan McDowell - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#include -#include -#include -#include -#include -#include - -/* - * Our context - */ -struct ams_delta_led { - struct led_classdev cdev; - u8 bitmask; -}; - -static void ams_delta_led_set(struct led_classdev *led_cdev, - enum led_brightness value) -{ - struct ams_delta_led *led_dev = - container_of(led_cdev, struct ams_delta_led, cdev); - - if (value) - ams_delta_latch1_write(led_dev->bitmask, led_dev->bitmask); - else - ams_delta_latch1_write(led_dev->bitmask, 0); -} - -static struct ams_delta_led ams_delta_leds[] = { - { - .cdev = { - .name = "ams-delta::camera", - .brightness_set = ams_delta_led_set, - }, - .bitmask = AMS_DELTA_LATCH1_LED_CAMERA, - }, - { - .cdev = { - .name = "ams-delta::advert", - .brightness_set = ams_delta_led_set, - }, - .bitmask = AMS_DELTA_LATCH1_LED_ADVERT, - }, - { - .cdev = { - .name = "ams-delta::email", - .brightness_set = ams_delta_led_set, - }, - .bitmask = AMS_DELTA_LATCH1_LED_EMAIL, - }, - { - .cdev = { - .name = "ams-delta::handsfree", - .brightness_set = ams_delta_led_set, - }, - .bitmask = AMS_DELTA_LATCH1_LED_HANDSFREE, - }, - { - .cdev = { - .name = "ams-delta::voicemail", - .brightness_set = ams_delta_led_set, - }, - .bitmask = AMS_DELTA_LATCH1_LED_VOICEMAIL, - }, - { - .cdev = { - .name = "ams-delta::voice", - .brightness_set = ams_delta_led_set, - }, - .bitmask = AMS_DELTA_LATCH1_LED_VOICE, - }, -}; - -static int ams_delta_led_probe(struct platform_device *pdev) -{ - int i, ret; - - for (i = 0; i < ARRAY_SIZE(ams_delta_leds); i++) { - ams_delta_leds[i].cdev.flags |= LED_CORE_SUSPENDRESUME; - ret = led_classdev_register(&pdev->dev, - &ams_delta_leds[i].cdev); - if (ret < 0) - goto fail; - } - - return 0; -fail: - while (--i >= 0) - led_classdev_unregister(&ams_delta_leds[i].cdev); - return ret; -} - -static int ams_delta_led_remove(struct platform_device *pdev) -{ - int i; - - for (i = 0; i < ARRAY_SIZE(ams_delta_leds); i++) - led_classdev_unregister(&ams_delta_leds[i].cdev); - - return 0; -} - -static struct platform_driver ams_delta_led_driver = { - .probe = ams_delta_led_probe, - .remove = ams_delta_led_remove, - .driver = { - .name = "ams-delta-led", - .owner = THIS_MODULE, - }, -}; - -static int __init ams_delta_led_init(void) -{ - return platform_driver_register(&ams_delta_led_driver); -} - -static void __exit ams_delta_led_exit(void) -{ - platform_driver_unregister(&ams_delta_led_driver); -} - -module_init(ams_delta_led_init); -module_exit(ams_delta_led_exit); - -MODULE_AUTHOR("Jonathan McDowell "); -MODULE_DESCRIPTION("Amstrad Delta LED driver"); -MODULE_LICENSE("GPL"); -MODULE_ALIAS("platform:ams-delta-led"); From 68f0676699fb0e0b18feb8459c35ecdfe3127b3d Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 00:08:55 +0100 Subject: [PATCH 05/82] MTD: NAND: ams-delta: use GPIO instead of custom I/O Don't use Amstrad Delta custom I/O functions for controlling the device, use GPIO API instead. While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB). Signed-off-by: Janusz Krzysztofik Cc: David Woodhouse Reviewed-by: Artem Bityutskiy Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/board-ams-delta.c | 30 -------- .../plat-omap/include/plat/board-ams-delta.h | 6 -- drivers/mtd/nand/ams-delta.c | 74 +++++++++++++------ 3 files changed, 52 insertions(+), 58 deletions(-) diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index 034d0094e93a..cc6f96249e77 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -236,36 +236,6 @@ static struct gpio latch_gpios[] __initconst = { .flags = GPIOF_OUT_INIT_LOW, .label = "lcd_ndisp", }, - { - .gpio = AMS_DELTA_GPIO_PIN_NAND_NCE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "nand_nce", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_NAND_NRE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "nand_nre", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_NAND_NWP, - .flags = GPIOF_OUT_INIT_LOW, - .label = "nand_nwp", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_NAND_NWE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "nand_nwe", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_NAND_ALE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "nand_ale", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_NAND_CLE, - .flags = GPIOF_OUT_INIT_LOW, - .label = "nand_cle", - }, { .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR, .flags = GPIOF_OUT_INIT_LOW, diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h index a0f86ca75ddc..3e578339fe8c 100644 --- a/arch/arm/plat-omap/include/plat/board-ams-delta.h +++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h @@ -30,12 +30,6 @@ #define AMS_DELTA_LATCH2_LCD_VBLEN 0x0001 #define AMS_DELTA_LATCH2_LCD_NDISP 0x0002 -#define AMS_DELTA_LATCH2_NAND_NCE 0x0004 -#define AMS_DELTA_LATCH2_NAND_NRE 0x0008 -#define AMS_DELTA_LATCH2_NAND_NWP 0x0010 -#define AMS_DELTA_LATCH2_NAND_NWE 0x0020 -#define AMS_DELTA_LATCH2_NAND_ALE 0x0040 -#define AMS_DELTA_LATCH2_NAND_CLE 0x0080 #define AMD_DELTA_LATCH2_KEYBRD_PWR 0x0100 #define AMD_DELTA_LATCH2_KEYBRD_DATA 0x0200 #define AMD_DELTA_LATCH2_SCARD_RSTIN 0x0400 diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c index 9e6b498c9beb..5769bd234283 100644 --- a/drivers/mtd/nand/ams-delta.c +++ b/drivers/mtd/nand/ams-delta.c @@ -26,7 +26,7 @@ #include #include #include -#include +#include #include /* @@ -34,8 +34,6 @@ */ static struct mtd_info *ams_delta_mtd = NULL; -#define NAND_MASK (AMS_DELTA_LATCH2_NAND_NRE | AMS_DELTA_LATCH2_NAND_NWE | AMS_DELTA_LATCH2_NAND_CLE | AMS_DELTA_LATCH2_NAND_ALE | AMS_DELTA_LATCH2_NAND_NCE | AMS_DELTA_LATCH2_NAND_NWP) - /* * Define partitions for flash devices */ @@ -68,10 +66,9 @@ static void ams_delta_write_byte(struct mtd_info *mtd, u_char byte) writew(0, io_base + OMAP_MPUIO_IO_CNTL); writew(byte, this->IO_ADDR_W); - ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE, 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 0); ndelay(40); - ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE, - AMS_DELTA_LATCH2_NAND_NWE); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 1); } static u_char ams_delta_read_byte(struct mtd_info *mtd) @@ -80,12 +77,11 @@ static u_char ams_delta_read_byte(struct mtd_info *mtd) struct nand_chip *this = mtd->priv; void __iomem *io_base = this->priv; - ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE, 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 0); ndelay(40); writew(~0, io_base + OMAP_MPUIO_IO_CNTL); res = readw(this->IO_ADDR_R); - ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE, - AMS_DELTA_LATCH2_NAND_NRE); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 1); return res; } @@ -132,15 +128,12 @@ static void ams_delta_hwcontrol(struct mtd_info *mtd, int cmd, { if (ctrl & NAND_CTRL_CHANGE) { - unsigned long bits; - - bits = (~ctrl & NAND_NCE) ? AMS_DELTA_LATCH2_NAND_NCE : 0; - bits |= (ctrl & NAND_CLE) ? AMS_DELTA_LATCH2_NAND_CLE : 0; - bits |= (ctrl & NAND_ALE) ? AMS_DELTA_LATCH2_NAND_ALE : 0; - - ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_CLE | - AMS_DELTA_LATCH2_NAND_ALE | - AMS_DELTA_LATCH2_NAND_NCE, bits); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NCE, + (ctrl & NAND_NCE) == 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_CLE, + (ctrl & NAND_CLE) != 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_ALE, + (ctrl & NAND_ALE) != 0); } if (cmd != NAND_CMD_NONE) @@ -152,6 +145,39 @@ static int ams_delta_nand_ready(struct mtd_info *mtd) return gpio_get_value(AMS_DELTA_GPIO_PIN_NAND_RB); } +static struct gpio _mandatory_gpio[] __initconst_or_module = { + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NCE, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nce", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NRE, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nre", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NWP, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nwp", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_NWE, + .flags = GPIOF_OUT_INIT_HIGH, + .label = "nand_nwe", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_ALE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_ale", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_NAND_CLE, + .flags = GPIOF_OUT_INIT_LOW, + .label = "nand_cle", + }, +}; + /* * Main initialization routine */ @@ -223,10 +249,9 @@ static int __devinit ams_delta_init(struct platform_device *pdev) platform_set_drvdata(pdev, io_base); /* Set chip enabled, but */ - ams_delta_latch2_write(NAND_MASK, AMS_DELTA_LATCH2_NAND_NRE | - AMS_DELTA_LATCH2_NAND_NWE | - AMS_DELTA_LATCH2_NAND_NCE | - AMS_DELTA_LATCH2_NAND_NWP); + err = gpio_request_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio)); + if (err) + goto out_gpio; /* Scan to find existence of the device */ if (nand_scan(ams_delta_mtd, 1)) { @@ -241,7 +266,10 @@ static int __devinit ams_delta_init(struct platform_device *pdev) goto out; out_mtd: + gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio)); +out_gpio: platform_set_drvdata(pdev, NULL); + gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB); iounmap(io_base); out_release_io: release_mem_region(res->start, resource_size(res)); @@ -262,6 +290,8 @@ static int __devexit ams_delta_cleanup(struct platform_device *pdev) /* Release resources, unregister device */ nand_release(ams_delta_mtd); + gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio)); + gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB); iounmap(io_base); release_mem_region(res->start, resource_size(res)); From a218d19f6a91c076c7ed8a7c0082f777248c5394 Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 00:08:56 +0100 Subject: [PATCH 06/82] omapfb: lcd_ams_delta: drive control lines over GPIO Don't use Amstrad Delta custom I/O functions any longer, use GPIO API instead. Signed-off-by: Janusz Krzysztofik Acked-by: Tomi Valkeinen Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/board-ams-delta.c | 10 ------- .../plat-omap/include/plat/board-ams-delta.h | 2 -- drivers/video/omap/lcd_ams_delta.c | 27 ++++++++++++++----- 3 files changed, 20 insertions(+), 19 deletions(-) diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index cc6f96249e77..3aba8f99cc7e 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -226,16 +226,6 @@ static struct gpio latch_gpios[] __initconst = { .flags = GPIOF_OUT_INIT_LOW, .label = "dockit2", }, - { - .gpio = AMS_DELTA_GPIO_PIN_LCD_VBLEN, - .flags = GPIOF_OUT_INIT_LOW, - .label = "lcd_vblen", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_LCD_NDISP, - .flags = GPIOF_OUT_INIT_LOW, - .label = "lcd_ndisp", - }, { .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR, .flags = GPIOF_OUT_INIT_LOW, diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h index 3e578339fe8c..e9ad673be32f 100644 --- a/arch/arm/plat-omap/include/plat/board-ams-delta.h +++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h @@ -28,8 +28,6 @@ #if defined (CONFIG_MACH_AMS_DELTA) -#define AMS_DELTA_LATCH2_LCD_VBLEN 0x0001 -#define AMS_DELTA_LATCH2_LCD_NDISP 0x0002 #define AMD_DELTA_LATCH2_KEYBRD_PWR 0x0100 #define AMD_DELTA_LATCH2_KEYBRD_DATA 0x0200 #define AMD_DELTA_LATCH2_SCARD_RSTIN 0x0400 diff --git a/drivers/video/omap/lcd_ams_delta.c b/drivers/video/omap/lcd_ams_delta.c index 6978ae4ef83a..73b211b92a39 100644 --- a/drivers/video/omap/lcd_ams_delta.c +++ b/drivers/video/omap/lcd_ams_delta.c @@ -25,6 +25,7 @@ #include #include #include +#include #include #include @@ -98,29 +99,41 @@ static struct lcd_ops ams_delta_lcd_ops = { /* omapfb panel section */ +static struct gpio _gpios[] __initconst_or_module = { + { + .gpio = AMS_DELTA_GPIO_PIN_LCD_VBLEN, + .flags = GPIOF_OUT_INIT_LOW, + .label = "lcd_vblen", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_LCD_NDISP, + .flags = GPIOF_OUT_INIT_LOW, + .label = "lcd_ndisp", + }, +}; + static int ams_delta_panel_init(struct lcd_panel *panel, struct omapfb_device *fbdev) { - return 0; + return gpio_request_array(_gpios, ARRAY_SIZE(_gpios)); } static void ams_delta_panel_cleanup(struct lcd_panel *panel) { + gpio_free_array(_gpios, ARRAY_SIZE(_gpios)); } static int ams_delta_panel_enable(struct lcd_panel *panel) { - ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_NDISP, - AMS_DELTA_LATCH2_LCD_NDISP); - ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_VBLEN, - AMS_DELTA_LATCH2_LCD_VBLEN); + gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_NDISP, 1); + gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_VBLEN, 1); return 0; } static void ams_delta_panel_disable(struct lcd_panel *panel) { - ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_VBLEN, 0); - ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_NDISP, 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_VBLEN, 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_NDISP, 0); } static unsigned long ams_delta_panel_get_caps(struct lcd_panel *panel) From 8d09a1bb3147ddbcf0a9483021ca699c54c54732 Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Tue, 20 Dec 2011 23:10:34 +0100 Subject: [PATCH 07/82] input: serio: ams-delta: toggle keyboard power over GPIO Don't use Amstrad Delta custom I/O functions once GPIO interface is available for the underlying hardware. While requesting and initializing GPIO pins used, also take care of one extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs to the device and affects its functioning. Once done, move the driver initialization back to the device_initcall level, reverting the temporary chane introduced with patch 1/7 "ARM: OMAP1: ams-delta: register latch dependent devices later". That change is no longer required once the driver takes care of registering used GPIO pins, and it's better to initialize the device before others using the latch2 based GPIO pins, otherwise a garbage is reported on boot, perhaps due to random data already captured by the FIQ handler while the keyboard related latch bits are written with random values during initialization of those other latch2 dependent devices. Signed-off-by: Janusz Krzysztofik Acked-by: Dmitry Torokhov [tony@atomide.com: renamed _gpios to ams_delta_gpios] Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/board-ams-delta.c | 10 ---- .../plat-omap/include/plat/board-ams-delta.h | 2 - drivers/input/serio/ams_delta_serio.c | 56 ++++++++++++------- 3 files changed, 35 insertions(+), 33 deletions(-) diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index 3aba8f99cc7e..673cf21a90f8 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -226,16 +226,6 @@ static struct gpio latch_gpios[] __initconst = { .flags = GPIOF_OUT_INIT_LOW, .label = "dockit2", }, - { - .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR, - .flags = GPIOF_OUT_INIT_LOW, - .label = "keybrd_pwr", - }, - { - .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT, - .flags = GPIOF_OUT_INIT_LOW, - .label = "keybrd_dataout", - }, { .gpio = AMS_DELTA_GPIO_PIN_SCARD_RSTIN, .flags = GPIOF_OUT_INIT_LOW, diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h index e9ad673be32f..027e79eead5e 100644 --- a/arch/arm/plat-omap/include/plat/board-ams-delta.h +++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h @@ -28,8 +28,6 @@ #if defined (CONFIG_MACH_AMS_DELTA) -#define AMD_DELTA_LATCH2_KEYBRD_PWR 0x0100 -#define AMD_DELTA_LATCH2_KEYBRD_DATA 0x0200 #define AMD_DELTA_LATCH2_SCARD_RSTIN 0x0400 #define AMD_DELTA_LATCH2_SCARD_CMDVCC 0x0800 #define AMS_DELTA_LATCH2_MODEM_NRESET 0x1000 diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c index 835d37abe62a..0571e2ec358b 100644 --- a/drivers/input/serio/ams_delta_serio.c +++ b/drivers/input/serio/ams_delta_serio.c @@ -92,8 +92,7 @@ static irqreturn_t ams_delta_serio_interrupt(int irq, void *dev_id) static int ams_delta_serio_open(struct serio *serio) { /* enable keyboard */ - ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR, - AMD_DELTA_LATCH2_KEYBRD_PWR); + gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 1); return 0; } @@ -101,9 +100,32 @@ static int ams_delta_serio_open(struct serio *serio) static void ams_delta_serio_close(struct serio *serio) { /* disable keyboard */ - ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR, 0); + gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 0); } +static struct gpio ams_delta_gpios[] __initconst_or_module = { + { + .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATA, + .flags = GPIOF_DIR_IN, + .label = "serio-data", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_CLK, + .flags = GPIOF_DIR_IN, + .label = "serio-clock", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR, + .flags = GPIOF_OUT_INIT_LOW, + .label = "serio-power", + }, + { + .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT, + .flags = GPIOF_OUT_INIT_LOW, + .label = "serio-dataout", + }, +}; + static int __init ams_delta_serio_init(void) { int err; @@ -123,19 +145,12 @@ static int __init ams_delta_serio_init(void) strlcpy(ams_delta_serio->phys, "GPIO/serio0", sizeof(ams_delta_serio->phys)); - err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_DATA, "serio-data"); + err = gpio_request_array(ams_delta_gpios, + ARRAY_SIZE(ams_delta_gpios)); if (err) { - pr_err("ams_delta_serio: Couldn't request gpio pin for data\n"); + pr_err("ams_delta_serio: Couldn't request gpio pins\n"); goto serio; } - gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_DATA); - - err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_CLK, "serio-clock"); - if (err) { - pr_err("ams_delta_serio: couldn't request gpio pin for clock\n"); - goto gpio_data; - } - gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_CLK); err = request_irq(gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK), ams_delta_serio_interrupt, IRQ_TYPE_EDGE_RISING, @@ -143,7 +158,7 @@ static int __init ams_delta_serio_init(void) if (err < 0) { pr_err("ams_delta_serio: couldn't request gpio interrupt %d\n", gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK)); - goto gpio_clk; + goto gpio; } /* * Since GPIO register handling for keyboard clock pin is performed @@ -157,21 +172,20 @@ static int __init ams_delta_serio_init(void) dev_info(&ams_delta_serio->dev, "%s\n", ams_delta_serio->name); return 0; -gpio_clk: - gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK); -gpio_data: - gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA); +gpio: + gpio_free_array(ams_delta_gpios, + ARRAY_SIZE(ams_delta_gpios)); serio: kfree(ams_delta_serio); return err; } -late_initcall(ams_delta_serio_init); +module_init(ams_delta_serio_init); static void __exit ams_delta_serio_exit(void) { serio_unregister_port(ams_delta_serio); free_irq(OMAP_GPIO_IRQ(AMS_DELTA_GPIO_PIN_KEYBRD_CLK), 0); - gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK); - gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA); + gpio_free_array(ams_delta_gpios, + ARRAY_SIZE(ams_delta_gpios)); } module_exit(ams_delta_serio_exit); From ec00466944bb10d4c91d889d11cc90055115df8f Mon Sep 17 00:00:00 2001 From: Kamil Debski Date: Tue, 27 Dec 2011 17:16:47 +0900 Subject: [PATCH 08/82] ARM: EXYNOS: add G2D to mach-nuri Signed-off-by: Kamil Debski Signed-off-by: Kyungmin Park Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/Kconfig | 1 + arch/arm/mach-exynos/mach-nuri.c | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 5d602f68a0e8..abfa9c5213e7 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -273,6 +273,7 @@ config MACH_NURI select S5P_DEV_FIMC1 select S5P_DEV_FIMC2 select S5P_DEV_FIMC3 + select S5P_DEV_G2D select S5P_DEV_MFC select S5P_DEV_USB_EHCI select S5P_SETUP_MIPIPHY diff --git a/arch/arm/mach-exynos/mach-nuri.c b/arch/arm/mach-exynos/mach-nuri.c index b895ec031105..165c87638895 100644 --- a/arch/arm/mach-exynos/mach-nuri.c +++ b/arch/arm/mach-exynos/mach-nuri.c @@ -1259,6 +1259,7 @@ static struct platform_device *nuri_devices[] __initdata = { &s3c_device_i2c3, &i2c9_gpio, &s3c_device_adc, + &s5p_device_g2d, &s3c_device_rtc, &s5p_device_mfc, &s5p_device_mfc_l, From 2cd11b09a3a0ba2f247bf740e2213b912760a1b2 Mon Sep 17 00:00:00 2001 From: Kamil Debski Date: Tue, 27 Dec 2011 17:16:50 +0900 Subject: [PATCH 09/82] ARM: EXYNOS: add G2D to mach-universal Signed-off-by: Kamil Debski Signed-off-by: Kyungmin Park Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/Kconfig | 1 + arch/arm/mach-exynos/mach-universal_c210.c | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index abfa9c5213e7..e7830fd4bc31 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -230,6 +230,7 @@ config MACH_UNIVERSAL_C210 select S5P_DEV_FIMC1 select S5P_DEV_FIMC2 select S5P_DEV_FIMC3 + select S5P_DEV_G2D select S5P_DEV_CSIS0 select S5P_DEV_FIMD0 select S3C_DEV_HSMMC diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-exynos/mach-universal_c210.c index 37ac93e8d6d9..dd7510170e5a 100644 --- a/arch/arm/mach-exynos/mach-universal_c210.c +++ b/arch/arm/mach-exynos/mach-universal_c210.c @@ -960,6 +960,7 @@ static struct platform_device *universal_devices[] __initdata = { &s5p_device_fimc1, &s5p_device_fimc2, &s5p_device_fimc3, + &s5p_device_g2d, &mmc0_fixed_voltage, &s3c_device_hsmmc0, &s3c_device_hsmmc2, From 62d30f86f1f76e11819fb06c1597c7e7f1d620c2 Mon Sep 17 00:00:00 2001 From: Sangwook Lee Date: Thu, 3 Nov 2011 16:14:14 +0900 Subject: [PATCH 10/82] ARM: EXYNOS: Enable Bluetooth on ORIGEN This patch enables Bluetooth support on ORIGEN board. Signed-off-by: Sangwook Lee Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/mach-origen.c | 34 ++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+) diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-exynos/mach-origen.c index 0679b8ad2d1e..7bf8133502b3 100644 --- a/arch/arm/mach-exynos/mach-origen.c +++ b/arch/arm/mach-exynos/mach-origen.c @@ -20,6 +20,7 @@ #include #include #include +#include #include #include @@ -235,6 +236,7 @@ static struct regulator_init_data __initdata max8997_ldo9_data = { .min_uV = 2800000, .max_uV = 2800000, .apply_uV = 1, + .always_on = 1, .valid_ops_mask = REGULATOR_CHANGE_STATUS, .state_mem = { .disabled = 1, @@ -278,6 +280,7 @@ static struct regulator_init_data __initdata max8997_ldo14_data = { .min_uV = 1800000, .max_uV = 1800000, .apply_uV = 1, + .always_on = 1, .valid_ops_mask = REGULATOR_CHANGE_STATUS, .state_mem = { .disabled = 1, @@ -293,6 +296,7 @@ static struct regulator_init_data __initdata max8997_ldo17_data = { .min_uV = 3300000, .max_uV = 3300000, .apply_uV = 1, + .always_on = 1, .valid_ops_mask = REGULATOR_CHANGE_STATUS, .state_mem = { .disabled = 1, @@ -602,6 +606,23 @@ static struct s3c_fb_platdata origen_lcd_pdata __initdata = { .setup_gpio = exynos4_fimd0_gpio_setup_24bpp, }; +/* Bluetooth rfkill gpio platform data */ +struct rfkill_gpio_platform_data origen_bt_pdata = { + .reset_gpio = EXYNOS4_GPX2(2), + .shutdown_gpio = -1, + .type = RFKILL_TYPE_BLUETOOTH, + .name = "origen-bt", +}; + +/* Bluetooth Platform device */ +static struct platform_device origen_device_bluetooth = { + .name = "rfkill_gpio", + .id = -1, + .dev = { + .platform_data = &origen_bt_pdata, + }, +}; + static struct platform_device *origen_devices[] __initdata = { &s3c_device_hsmmc2, &s3c_device_hsmmc0, @@ -630,6 +651,7 @@ static struct platform_device *origen_devices[] __initdata = { &exynos4_device_pd[PD_MFC], &origen_device_gpiokeys, &origen_lcd_hv070wsa, + &origen_device_bluetooth, }; /* LCD Backlight data */ @@ -643,6 +665,16 @@ static struct platform_pwm_backlight_data origen_bl_data = { .pwm_period_ns = 1000, }; +static void __init origen_bt_setup(void) +{ + gpio_request(EXYNOS4_GPA0(0), "GPIO BT_UART"); + /* 4 UART Pins configuration */ + s3c_gpio_cfgrange_nopull(EXYNOS4_GPA0(0), 4, S3C_GPIO_SFN(2)); + /* Setup BT Reset, this gpio will be requesed by rfkill-gpio */ + s3c_gpio_cfgpin(EXYNOS4_GPX2(2), S3C_GPIO_OUTPUT); + s3c_gpio_setpull(EXYNOS4_GPX2(2), S3C_GPIO_PULL_NONE); +} + static void s5p_tv_setup(void) { /* Direct HPD to HDMI chip */ @@ -703,6 +735,8 @@ static void __init origen_machine_init(void) s5p_device_mfc.dev.parent = &exynos4_device_pd[PD_MFC].dev; samsung_bl_set(&origen_bl_gpio_info, &origen_bl_data); + + origen_bt_setup(); } MACHINE_START(ORIGEN, "ORIGEN") From 84207d83adc9a9b97d45d9cefaaf0ca766891b92 Mon Sep 17 00:00:00 2001 From: Sachin Kamat Date: Thu, 29 Dec 2011 16:46:16 +0900 Subject: [PATCH 11/82] ARM: EXYNOS: Enable G2D on ORIGEN This patch enables G2D support on ORIGEN board. Signed-off-by: Sachin Kamat Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/Kconfig | 1 + arch/arm/mach-exynos/mach-origen.c | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index e7830fd4bc31..bd4600eaa7d8 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -305,6 +305,7 @@ config MACH_ORIGEN select S5P_DEV_FIMC2 select S5P_DEV_FIMC3 select S5P_DEV_FIMD0 + select S5P_DEV_G2D select S5P_DEV_I2C_HDMIPHY select S5P_DEV_MFC select S5P_DEV_TV diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-exynos/mach-origen.c index 7bf8133502b3..e1d87b9a33e3 100644 --- a/arch/arm/mach-exynos/mach-origen.c +++ b/arch/arm/mach-exynos/mach-origen.c @@ -635,6 +635,7 @@ static struct platform_device *origen_devices[] __initdata = { &s5p_device_fimc2, &s5p_device_fimc3, &s5p_device_fimd0, + &s5p_device_g2d, &s5p_device_hdmi, &s5p_device_i2c_hdmiphy, &s5p_device_mfc, From 66211f98d611056bf5fe918bbda37c636688574e Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 29 Dec 2011 18:05:29 +0900 Subject: [PATCH 12/82] ARM: S3C64XX: Support GPIO LEDs on Cragganmore Cragganmore has a bank of 8 LEDs connected to the memory mapped GPIO bank, mostly intended for low level diagnostics. Register these with the LED subsystem for runtime use. Signed-off-by: Mark Brown Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c64xx/Kconfig | 1 + arch/arm/mach-s3c64xx/mach-crag6410.c | 51 +++++++++++++++++++++++++++ 2 files changed, 52 insertions(+) diff --git a/arch/arm/mach-s3c64xx/Kconfig b/arch/arm/mach-s3c64xx/Kconfig index dd20c66cd700..dc451232cf47 100644 --- a/arch/arm/mach-s3c64xx/Kconfig +++ b/arch/arm/mach-s3c64xx/Kconfig @@ -296,5 +296,6 @@ config MACH_WLF_CRAGG_6410 select S3C64XX_DEV_SPI0 select SAMSUNG_GPIO_EXTRA128 select I2C + select LEDS_GPIO_REGISTER help Machine support for the Wolfson Cragganmore S3C6410 variant. diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 8077f650eb0e..9da2d78f12f2 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -19,6 +19,7 @@ #include #include #include +#include #include #include #include @@ -698,6 +699,54 @@ static struct s3c_sdhci_platdata crag6410_hsmmc0_pdata = { .cfg_gpio = crag6410_cfg_sdhci0, }; +static const struct gpio_led gpio_leds[] = { + { + .name = "d13:green:", + .gpio = MMGPIO_GPIO_BASE + 0, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d14:green:", + .gpio = MMGPIO_GPIO_BASE + 1, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d15:green:", + .gpio = MMGPIO_GPIO_BASE + 2, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d16:green:", + .gpio = MMGPIO_GPIO_BASE + 3, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d17:green:", + .gpio = MMGPIO_GPIO_BASE + 4, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d18:green:", + .gpio = MMGPIO_GPIO_BASE + 5, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d19:green:", + .gpio = MMGPIO_GPIO_BASE + 6, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "d20:green:", + .gpio = MMGPIO_GPIO_BASE + 7, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, +}; + +static const struct gpio_led_platform_data gpio_leds_pdata = { + .leds = gpio_leds, + .num_leds = ARRAY_SIZE(gpio_leds), +}; + static void __init crag6410_machine_init(void) { /* Open drain IRQs need pullups */ @@ -730,6 +779,8 @@ static void __init crag6410_machine_init(void) platform_add_devices(crag6410_devices, ARRAY_SIZE(crag6410_devices)); + gpio_led_register_device(-1, &gpio_leds_pdata); + regulator_has_full_constraints(); s3c64xx_pm_init(); From 6e2f2b4a4bf7b351df0ada2a0d626478a4f82b8e Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 30 Dec 2011 10:00:07 +0900 Subject: [PATCH 13/82] ARM: S3C64XX: Fix build of Cragganmore after SPI changes Commit 875a59 (ARM: SAMSUNG: Consolidation of SPI platform devices to plat-samsung) replaced the function s3c64xx_spi_set_info() with s3c64xx_spiN_set_platdata() but did not update all the machines, with Cragganmore being left. Fix that. Signed-off-by: Mark Brown Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c64xx/mach-crag6410.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 9da2d78f12f2..97bd8574d4c9 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -776,6 +776,7 @@ static void __init crag6410_machine_init(void) i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1)); samsung_keypad_set_platdata(&crag6410_keypad_data); + s3c64xx_spi0_set_platdata(NULL, 0, 1); platform_add_devices(crag6410_devices, ARRAY_SIZE(crag6410_devices)); From fb7f60f3ff46cdcee15aed089edd6c298a1b80de Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 30 Dec 2011 13:44:31 +0900 Subject: [PATCH 14/82] ARM: S3C64XX: Enable power management for disk on Cragganmore We can happily let the MMC stack do power management for the MMC card that is our main disk on Cragganmore so let's enable it. Signed-off-by: Mark Brown Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c64xx/mach-crag6410.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 97bd8574d4c9..894a5092a0dd 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -21,6 +21,7 @@ #include #include #include +#include #include #include #include @@ -697,6 +698,7 @@ static struct s3c_sdhci_platdata crag6410_hsmmc0_pdata = { .max_width = 4, .cd_type = S3C_SDHCI_CD_INTERNAL, .cfg_gpio = crag6410_cfg_sdhci0, + .host_caps = MMC_CAP_POWER_OFF_CARD, }; static const struct gpio_led gpio_leds[] = { From a9294cdc17d4f9d16eac3bc42afba9e96c6ad4e4 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 30 Dec 2011 13:44:36 +0900 Subject: [PATCH 15/82] ARM: S3C64XX: Enable power management for WiFi on Cragganmore Allow the SDHCI stack to runtime power manage the WiFi card on Cragganmore for better power optimisation. Signed-off-by: Mark Brown Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c64xx/mach-crag6410.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 894a5092a0dd..7539a2999178 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -683,6 +683,7 @@ static void __init crag6410_map_io(void) static struct s3c_sdhci_platdata crag6410_hsmmc2_pdata = { .max_width = 4, .cd_type = S3C_SDHCI_CD_PERMANENT, + .host_caps = MMC_CAP_POWER_OFF_CARD, }; static void crag6410_cfg_sdhci0(struct platform_device *dev, int width) From cda2349a9b63fc51f3ca2953020e0f5ea9e2965c Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 12 Jan 2012 11:04:56 +0900 Subject: [PATCH 16/82] ARM: S3C64XX: Add hookup for Tomatin module on Cragganmore The Tomatin module carries a WM0010 audio DSP. Provide basic hookup for this, though additional platform data will be needed to fully integrate with the driver. Signed-off-by: Mark Brown Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c64xx/mach-crag6410-module.c | 27 +++++++++++++++++++- arch/arm/mach-s3c64xx/mach-crag6410.c | 11 +++++++- 2 files changed, 36 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c index cd3c97e2ee75..b4ed351e701d 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include @@ -21,8 +22,25 @@ #include #include +#include + #include +static struct s3c64xx_spi_csinfo wm0010_spi_csinfo = { + .set_level = gpio_set_value, + .line = S3C64XX_GPC(3), +}; + +static struct spi_board_info wm1253_devs[] = { + [0] = { + .modalias = "wm0010", + .bus_num = 0, + .chip_select = 0, + .mode = SPI_MODE_0, + .controller_data = &wm0010_spi_csinfo, + }, +}; + static struct wm5100_pdata wm5100_pdata = { .ldo_ena = S3C64XX_GPN(7), .irq_flags = IRQF_TRIGGER_HIGH, @@ -158,6 +176,8 @@ static __devinitdata const struct { const char *name; const struct i2c_board_info *i2c_devs; int num_i2c_devs; + const struct spi_board_info *spi_devs; + int num_spi_devs; } gf_mods[] = { { .id = 0x01, .name = "1250-EV1 Springbank" }, { .id = 0x02, .name = "1251-EV1 Jura" }, @@ -165,7 +185,8 @@ static __devinitdata const struct { { .id = 0x11, .name = "6249-EV2 Glenfarclas", }, { .id = 0x21, .name = "1275-EV1 Mortlach" }, { .id = 0x25, .name = "1274-EV1 Glencadam" }, - { .id = 0x31, .name = "1253-EV1 Tomatin", }, + { .id = 0x31, .name = "1253-EV1 Tomatin", + .spi_devs = wm1253_devs, .num_spi_devs = ARRAY_SIZE(wm1253_devs) }, { .id = 0x39, .name = "1254-EV1 Dallas Dhu", .i2c_devs = wm1254_devs, .num_i2c_devs = ARRAY_SIZE(wm1254_devs) }, { .id = 0x3a, .name = "1259-EV1 Tobermory", @@ -197,12 +218,16 @@ static __devinit int wlf_gf_module_probe(struct i2c_client *i2c, if (i < ARRAY_SIZE(gf_mods)) { dev_info(&i2c->dev, "%s revision %d\n", gf_mods[i].name, rev + 1); + for (j = 0; j < gf_mods[i].num_i2c_devs; j++) { if (!i2c_new_device(i2c->adapter, &(gf_mods[i].i2c_devs[j]))) dev_err(&i2c->dev, "Failed to register dev: %d\n", ret); } + + spi_register_board_info(gf_mods[i].spi_devs, + gf_mods[i].num_spi_devs); } else { dev_warn(&i2c->dev, "Unknown module ID 0x%x revision %d\n", id, rev + 1); diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 7539a2999178..f93caad1dd9b 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -576,11 +576,19 @@ static struct s3c2410_platform_i2c i2c0_pdata = { .frequency = 400000, }; +static struct regulator_consumer_supply pvdd_1v2_consumers[] __initdata = { + REGULATOR_SUPPLY("DCVDD", "spi0.0"), + REGULATOR_SUPPLY("AVDD", "spi0.0"), +}; + static struct regulator_init_data pvdd_1v2 __initdata = { .constraints = { .name = "PVDD_1V2", - .always_on = 1, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, }, + + .consumer_supplies = pvdd_1v2_consumers, + .num_consumer_supplies = ARRAY_SIZE(pvdd_1v2_consumers), }; static struct regulator_consumer_supply pvdd_1v8_consumers[] __initdata = { @@ -594,6 +602,7 @@ static struct regulator_consumer_supply pvdd_1v8_consumers[] __initdata = { REGULATOR_SUPPLY("AVDD2", "1-001a"), REGULATOR_SUPPLY("DCVDD", "1-001a"), REGULATOR_SUPPLY("AVDD", "1-001a"), + REGULATOR_SUPPLY("DBVDD", "spi0.0"), }; static struct regulator_init_data pvdd_1v8 __initdata = { From 845da6bf65b1ebff700c1e9a8c17f5df303792c1 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Fri, 6 Jan 2012 09:11:40 +0800 Subject: [PATCH 17/82] ARM: mxs: detect SoC by checking CHIPID register Both imx23 and imx28 have CHIPID register at address 0x8001c310, which can be used to identify the SoC. This patch changes cpu_is_xxx and __arch_decomp_setup to use this CHIPID register than machine type to detect the chip between imx23 and imx28, so that we do not need to change these functions whenever a new board/machine gets added. Suggested-by: Wolfram Sang Signed-off-by: Shawn Guo Acked-by: Wolfram Sang --- arch/arm/mach-mxs/include/mach/digctl.h | 1 + arch/arm/mach-mxs/include/mach/mxs.h | 29 ++++++++++++--------- arch/arm/mach-mxs/include/mach/uncompress.h | 13 +++++---- 3 files changed, 23 insertions(+), 20 deletions(-) diff --git a/arch/arm/mach-mxs/include/mach/digctl.h b/arch/arm/mach-mxs/include/mach/digctl.h index 49a888c65d6d..17964066303f 100644 --- a/arch/arm/mach-mxs/include/mach/digctl.h +++ b/arch/arm/mach-mxs/include/mach/digctl.h @@ -18,4 +18,5 @@ #define HW_DIGCTL_CTRL 0x0 #define BP_DIGCTL_CTRL_SAIF_CLKMUX 10 #define BM_DIGCTL_CTRL_SAIF_CLKMUX (0x3 << 10) +#define HW_DIGCTL_CHIPID 0x310 #endif diff --git a/arch/arm/mach-mxs/include/mach/mxs.h b/arch/arm/mach-mxs/include/mach/mxs.h index bde5f6634747..7d4fb6d0afda 100644 --- a/arch/arm/mach-mxs/include/mach/mxs.h +++ b/arch/arm/mach-mxs/include/mach/mxs.h @@ -23,21 +23,9 @@ #include #endif #include +#include #include -/* - * MXS CPU types - */ -#define cpu_is_mx23() ( \ - machine_is_mx23evk() || \ - machine_is_stmp378x() || \ - 0) -#define cpu_is_mx28() ( \ - machine_is_mx28evk() || \ - machine_is_m28evk() || \ - machine_is_tx28() || \ - 0) - /* * IO addresses common to MXS-based */ @@ -109,6 +97,21 @@ static inline void __mxs_togl(u32 mask, void __iomem *reg) { __raw_writel(mask, reg + MXS_TOG_ADDR); } + +/* + * MXS CPU types + */ +#define MXS_CHIPID (MXS_IO_ADDRESS(MXS_DIGCTL_BASE_ADDR) + HW_DIGCTL_CHIPID) + +static inline int cpu_is_mx23(void) +{ + return ((__raw_readl(MXS_CHIPID) >> 16) == 0x3780); +} + +static inline int cpu_is_mx28(void) +{ + return ((__raw_readl(MXS_CHIPID) >> 16) == 0x2800); +} #endif #endif /* __MACH_MXS_H__ */ diff --git a/arch/arm/mach-mxs/include/mach/uncompress.h b/arch/arm/mach-mxs/include/mach/uncompress.h index 67776746f143..ef2811495446 100644 --- a/arch/arm/mach-mxs/include/mach/uncompress.h +++ b/arch/arm/mach-mxs/include/mach/uncompress.h @@ -18,8 +18,6 @@ #ifndef __MACH_MXS_UNCOMPRESS_H__ #define __MACH_MXS_UNCOMPRESS_H__ -#include - unsigned long mxs_duart_base; #define MXS_DUART(x) (*(volatile unsigned long *)(mxs_duart_base + (x))) @@ -55,16 +53,17 @@ static inline void flush(void) #define MX23_DUART_BASE_ADDR 0x80070000 #define MX28_DUART_BASE_ADDR 0x80074000 +#define MXS_DIGCTL_CHIPID 0x8001c310 static inline void __arch_decomp_setup(unsigned long arch_id) { - switch (arch_id) { - case MACH_TYPE_MX23EVK: + u16 chipid = (*(volatile unsigned long *) MXS_DIGCTL_CHIPID) >> 16; + + switch (chipid) { + case 0x3780: mxs_duart_base = MX23_DUART_BASE_ADDR; break; - case MACH_TYPE_MX28EVK: - case MACH_TYPE_M28EVK: - case MACH_TYPE_TX28: + case 0x2800: mxs_duart_base = MX28_DUART_BASE_ADDR; break; default: From 554f01fbc632cf37969774b9dfdce1701581f465 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 27 Jan 2012 14:58:46 +0900 Subject: [PATCH 18/82] ARM: S3C64XX: Add a SPKVDD supply for CODECs on Cragganmore Hook up a SPKVDD supply for CODECs that can use it. Signed-off-by: Mark Brown Signed-off-by: Kukjin Kim --- arch/arm/mach-s3c64xx/mach-crag6410.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index f93caad1dd9b..79f993495fd3 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -300,6 +300,7 @@ static struct platform_device littlemill_device = { }; static struct regulator_consumer_supply wallvdd_consumers[] = { + REGULATOR_SUPPLY("SPKVDD", "1-001a"), REGULATOR_SUPPLY("SPKVDD1", "1-001a"), REGULATOR_SUPPLY("SPKVDD2", "1-001a"), REGULATOR_SUPPLY("SPKVDDL", "1-001a"), From bcd7bd377393cccf58a2cf010bc8227fc7df1413 Mon Sep 17 00:00:00 2001 From: Sylwester Nawrocki Date: Tue, 31 Jan 2012 13:26:54 +0900 Subject: [PATCH 19/82] ARM: EXYNOS: Increase virtual framebuffer size on Universal C210 board Increase framebuffer virtual size to enable display panning. Signed-off-by: Sylwester Nawrocki Signed-off-by: Kyungmin Park Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/mach-universal_c210.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-exynos/mach-universal_c210.c index dd7510170e5a..0e01f047be5e 100644 --- a/arch/arm/mach-exynos/mach-universal_c210.c +++ b/arch/arm/mach-exynos/mach-universal_c210.c @@ -817,6 +817,8 @@ static struct s3c_fb_pd_win universal_fb_win0 = { }, .max_bpp = 32, .default_bpp = 16, + .virtual_x = 480, + .virtual_y = 2 * 800, }; static struct s3c_fb_platdata universal_lcd_pdata __initdata = { From 9c01c96caaea89088b9c461a0013ed770b586fbd Mon Sep 17 00:00:00 2001 From: Sylwester Nawrocki Date: Tue, 31 Jan 2012 13:26:58 +0900 Subject: [PATCH 20/82] ARM: EXYNOS: Add support for S5K6AAFX image sensor on Universal C210 board Add voltage regulator and platform data definitions for S5K6AAFX image sensor driver. Signed-off-by: Sylwester Nawrocki Signed-off-by: Kyungmin Park Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/mach-universal_c210.c | 74 ++++++++++++++++++++-- 1 file changed, 70 insertions(+), 4 deletions(-) diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-exynos/mach-universal_c210.c index 0e01f047be5e..44fc43e06a6a 100644 --- a/arch/arm/mach-exynos/mach-universal_c210.c +++ b/arch/arm/mach-exynos/mach-universal_c210.c @@ -46,6 +46,7 @@ #include #include #include +#include #include "common.h" @@ -122,8 +123,10 @@ static struct regulator_consumer_supply lp3974_buck1_consumer = static struct regulator_consumer_supply lp3974_buck2_consumer = REGULATOR_SUPPLY("vddg3d", NULL); -static struct regulator_consumer_supply lp3974_buck3_consumer = - REGULATOR_SUPPLY("vdet", "s5p-sdo"); +static struct regulator_consumer_supply lp3974_buck3_consumer[] = { + REGULATOR_SUPPLY("vdet", "s5p-sdo"), + REGULATOR_SUPPLY("vdd_reg", "0-003c"), +}; static struct regulator_init_data lp3974_buck1_data = { .constraints = { @@ -168,8 +171,8 @@ static struct regulator_init_data lp3974_buck3_data = { .enabled = 1, }, }, - .num_consumer_supplies = 1, - .consumer_supplies = &lp3974_buck3_consumer, + .num_consumer_supplies = ARRAY_SIZE(lp3974_buck3_consumer), + .consumer_supplies = lp3974_buck3_consumer, }; static struct regulator_init_data lp3974_buck4_data = { @@ -302,6 +305,9 @@ static struct regulator_init_data lp3974_ldo8_data = { .consumer_supplies = lp3974_ldo8_consumer, }; +static struct regulator_consumer_supply lp3974_ldo9_consumer = + REGULATOR_SUPPLY("vddio", "0-003c"); + static struct regulator_init_data lp3974_ldo9_data = { .constraints = { .name = "VCC_2.8V", @@ -313,6 +319,8 @@ static struct regulator_init_data lp3974_ldo9_data = { .enabled = 1, }, }, + .num_consumer_supplies = 1, + .consumer_supplies = &lp3974_ldo9_consumer, }; static struct regulator_init_data lp3974_ldo10_data = { @@ -411,6 +419,7 @@ static struct regulator_init_data lp3974_ldo15_data = { }; static struct regulator_consumer_supply lp3974_ldo16_consumer[] = { + REGULATOR_SUPPLY("vdda", "0-003c"), REGULATOR_SUPPLY("a_sensor", "0-001f"), }; @@ -830,6 +839,28 @@ static struct s3c_fb_platdata universal_lcd_pdata __initdata = { .setup_gpio = exynos4_fimd0_gpio_setup_24bpp, }; +static struct regulator_consumer_supply cam_vt_dio_supply = + REGULATOR_SUPPLY("vdd_core", "0-003c"); + +static struct regulator_init_data cam_vt_dio_reg_init_data = { + .constraints = { .valid_ops_mask = REGULATOR_CHANGE_STATUS }, + .num_consumer_supplies = 1, + .consumer_supplies = &cam_vt_dio_supply, +}; + +static struct fixed_voltage_config cam_vt_dio_fixed_voltage_cfg = { + .supply_name = "CAM_VT_D_IO", + .microvolts = 2800000, + .gpio = EXYNOS4_GPE2(1), /* CAM_PWR_EN2 */ + .enable_high = 1, + .init_data = &cam_vt_dio_reg_init_data, +}; + +static struct platform_device cam_vt_dio_fixed_reg_dev = { + .name = "reg-fixed-voltage", .id = FIXED_REG_ID_CAM_VT_DIO, + .dev = { .platform_data = &cam_vt_dio_fixed_voltage_cfg }, +}; + static struct regulator_consumer_supply cam_i_core_supply = REGULATOR_SUPPLY("core", "0-001f"); @@ -885,6 +916,28 @@ static struct s5p_platform_mipi_csis mipi_csis_platdata = { #define GPIO_CAM_LEVEL_EN(n) EXYNOS4_GPE4(n + 3) #define GPIO_CAM_8M_ISP_INT EXYNOS4_GPX1(5) /* XEINT_13 */ #define GPIO_CAM_MEGA_nRST EXYNOS4_GPE2(5) +#define GPIO_CAM_VGA_NRST EXYNOS4_GPE4(7) +#define GPIO_CAM_VGA_NSTBY EXYNOS4_GPE4(6) + +static int s5k6aa_set_power(int on) +{ + gpio_set_value(GPIO_CAM_LEVEL_EN(2), !!on); + return 0; +} + +static struct s5k6aa_platform_data s5k6aa_platdata = { + .mclk_frequency = 21600000UL, + .gpio_reset = { GPIO_CAM_VGA_NRST, 0 }, + .gpio_stby = { GPIO_CAM_VGA_NSTBY, 0 }, + .bus_type = V4L2_MBUS_PARALLEL, + .horiz_flip = 1, + .set_power = s5k6aa_set_power, +}; + +static struct i2c_board_info s5k6aa_board_info = { + I2C_BOARD_INFO("S5K6AA", 0x3C), + .platform_data = &s5k6aa_platdata, +}; static int m5mols_set_power(struct device *dev, int on) { @@ -906,6 +959,14 @@ static struct i2c_board_info m5mols_board_info = { static struct s5p_fimc_isp_info universal_camera_sensors[] = { { + .mux_id = 0, + .flags = V4L2_MBUS_PCLK_SAMPLE_FALLING | + V4L2_MBUS_VSYNC_ACTIVE_LOW, + .bus_type = FIMC_ITU_601, + .board_info = &s5k6aa_board_info, + .i2c_bus_num = 0, + .clk_frequency = 24000000UL, + }, { .mux_id = 0, .flags = V4L2_MBUS_PCLK_SAMPLE_FALLING | V4L2_MBUS_VSYNC_ACTIVE_LOW, @@ -927,6 +988,8 @@ static struct gpio universal_camera_gpios[] = { { GPIO_CAM_LEVEL_EN(2), GPIOF_OUT_INIT_LOW, "CAM_LVL_EN2" }, { GPIO_CAM_8M_ISP_INT, GPIOF_IN, "8M_ISP_INT" }, { GPIO_CAM_MEGA_nRST, GPIOF_OUT_INIT_LOW, "CAM_8M_NRST" }, + { GPIO_CAM_VGA_NRST, GPIOF_OUT_INIT_LOW, "CAM_VGA_NRST" }, + { GPIO_CAM_VGA_NSTBY, GPIOF_OUT_INIT_LOW, "CAM_VGA_NSTBY" }, }; static void universal_camera_init(void) @@ -950,6 +1013,8 @@ static void universal_camera_init(void) /* Free GPIOs controlled directly by the sensor drivers. */ gpio_free(GPIO_CAM_MEGA_nRST); gpio_free(GPIO_CAM_8M_ISP_INT); + gpio_free(GPIO_CAM_VGA_NRST); + gpio_free(GPIO_CAM_VGA_NSTBY); if (exynos4_fimc_setup_gpio(S5P_CAMPORT_A)) pr_err("Camera port A setup failed\n"); @@ -988,6 +1053,7 @@ static struct platform_device *universal_devices[] __initdata = { &exynos4_device_pd[PD_MFC], &exynos4_device_pd[PD_LCD0], &exynos4_device_pd[PD_CAM], + &cam_vt_dio_fixed_reg_dev, &cam_i_core_fixed_reg_dev, &cam_s_if_fixed_reg_dev, &s5p_device_fimc_md, From 8f114e6eb1c3bb1ed6cd4904a8925a6d75a0a21e Mon Sep 17 00:00:00 2001 From: Sylwester Nawrocki Date: Tue, 31 Jan 2012 13:27:02 +0900 Subject: [PATCH 21/82] ARM: SAMSUNG: Add support for S5K6AAFX camera on Nuri board Add voltage regulator and platform data definitions for S5K6AAFX sensor driver and configure I2C6 bus timings. Signed-off-by: Sylwester Nawrocki Signed-off-by: HeungJun Kim Signed-off-by: Kyungmin Park Signed-off-by: Kukjin Kim --- arch/arm/mach-exynos/Kconfig | 2 + arch/arm/mach-exynos/mach-nuri.c | 65 ++++++++++++++++++++++++++++++++ 2 files changed, 67 insertions(+) diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index bd4600eaa7d8..9a427bc10d2b 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -269,6 +269,7 @@ config MACH_NURI select S3C_DEV_I2C1 select S3C_DEV_I2C3 select S3C_DEV_I2C5 + select S3C_DEV_I2C6 select S5P_DEV_CSIS0 select S5P_DEV_FIMC0 select S5P_DEV_FIMC1 @@ -285,6 +286,7 @@ config MACH_NURI select EXYNOS4_SETUP_I2C1 select EXYNOS4_SETUP_I2C3 select EXYNOS4_SETUP_I2C5 + select EXYNOS4_SETUP_I2C6 select EXYNOS4_SETUP_SDHCI select EXYNOS4_SETUP_USB_PHY select S5P_SETUP_MIPIPHY diff --git a/arch/arm/mach-exynos/mach-nuri.c b/arch/arm/mach-exynos/mach-nuri.c index 165c87638895..cc8d2f6bab2b 100644 --- a/arch/arm/mach-exynos/mach-nuri.c +++ b/arch/arm/mach-exynos/mach-nuri.c @@ -28,6 +28,7 @@ #include