Merge branches 'ib-mfd-gpio-4.12', 'ib-mfd-iio-input-4.12', 'ib-mfd-input-4.12', 'ib-mfd-leds-4.12', 'ib-mfd-phy-4.12' and 'ib-mfd-pinctrl-samsung-4.12' into ibs-for-mfd-merged
This commit is contained in:
Lee Jones
commit
18973ceb89
|
|
@ -0,0 +1,20 @@
|
|||
Motorola CPCAP on key
|
||||
|
||||
This module is part of the CPCAP. For more details about the whole
|
||||
chip see Documentation/devicetree/bindings/mfd/motorola-cpcap.txt.
|
||||
|
||||
This module provides a simple power button event via an Interrupt.
|
||||
|
||||
Required properties:
|
||||
- compatible: should be one of the following
|
||||
- "motorola,cpcap-pwrbutton"
|
||||
- interrupts: irq specifier for CPCAP's ON IRQ
|
||||
|
||||
Example:
|
||||
|
||||
&cpcap {
|
||||
cpcap_pwrbutton: pwrbutton {
|
||||
compatible = "motorola,cpcap-pwrbutton";
|
||||
interrupts = <23 IRQ_TYPE_NONE>;
|
||||
};
|
||||
};
|
||||
|
|
@ -229,6 +229,19 @@ config EXYNOS_ADC
|
|||
To compile this driver as a module, choose M here: the module will be
|
||||
called exynos_adc.
|
||||
|
||||
config MXS_LRADC_ADC
|
||||
tristate "Freescale i.MX23/i.MX28 LRADC ADC"
|
||||
depends on MFD_MXS_LRADC
|
||||
select IIO_BUFFER
|
||||
select IIO_TRIGGERED_BUFFER
|
||||
help
|
||||
Say yes here to build support for the ADC functions of the
|
||||
i.MX23/i.MX28 LRADC. This includes general-purpose ADC readings,
|
||||
battery voltage measurement, and die temperature measurement.
|
||||
|
||||
This driver can also be built as a module. If so, the module will be
|
||||
called mxs-lradc-adc.
|
||||
|
||||
config FSL_MX25_ADC
|
||||
tristate "Freescale MX25 ADC driver"
|
||||
depends on MFD_MX25_TSADC
|
||||
|
|
@ -411,20 +424,6 @@ config MESON_SARADC
|
|||
To compile this driver as a module, choose M here: the
|
||||
module will be called meson_saradc.
|
||||
|
||||
config MXS_LRADC
|
||||
tristate "Freescale i.MX23/i.MX28 LRADC"
|
||||
depends on (ARCH_MXS || COMPILE_TEST) && HAS_IOMEM
|
||||
depends on INPUT
|
||||
select STMP_DEVICE
|
||||
select IIO_BUFFER
|
||||
select IIO_TRIGGERED_BUFFER
|
||||
help
|
||||
Say yes here to build support for i.MX23/i.MX28 LRADC convertor
|
||||
built into these chips.
|
||||
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called mxs-lradc.
|
||||
|
||||
config NAU7802
|
||||
tristate "Nuvoton NAU7802 ADC driver"
|
||||
depends on I2C
|
||||
|
|
|
|||
|
|
@ -39,7 +39,7 @@ obj-$(CONFIG_MCP3422) += mcp3422.o
|
|||
obj-$(CONFIG_MEDIATEK_MT6577_AUXADC) += mt6577_auxadc.o
|
||||
obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
|
||||
obj-$(CONFIG_MESON_SARADC) += meson_saradc.o
|
||||
obj-$(CONFIG_MXS_LRADC) += mxs-lradc.o
|
||||
obj-$(CONFIG_MXS_LRADC_ADC) += mxs-lradc-adc.o
|
||||
obj-$(CONFIG_NAU7802) += nau7802.o
|
||||
obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
|
||||
obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,843 @@
|
|||
/*
|
||||
* Freescale MXS LRADC ADC driver
|
||||
*
|
||||
* Copyright (c) 2012 DENX Software Engineering, GmbH.
|
||||
* Copyright (c) 2017 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* Authors:
|
||||
* Marek Vasut <marex@denx.de>
|
||||
* Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/completion.h>
|
||||
#include <linux/device.h>
|
||||
#include <linux/err.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/mfd/core.h>
|
||||
#include <linux/mfd/mxs-lradc.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of_irq.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/sysfs.h>
|
||||
|
||||
#include <linux/iio/buffer.h>
|
||||
#include <linux/iio/iio.h>
|
||||
#include <linux/iio/trigger.h>
|
||||
#include <linux/iio/trigger_consumer.h>
|
||||
#include <linux/iio/triggered_buffer.h>
|
||||
#include <linux/iio/sysfs.h>
|
||||
|
||||
/*
|
||||
* Make this runtime configurable if necessary. Currently, if the buffered mode
|
||||
* is enabled, the LRADC takes LRADC_DELAY_TIMER_LOOP samples of data before
|
||||
* triggering IRQ. The sampling happens every (LRADC_DELAY_TIMER_PER / 2000)
|
||||
* seconds. The result is that the samples arrive every 500mS.
|
||||
*/
|
||||
#define LRADC_DELAY_TIMER_PER 200
|
||||
#define LRADC_DELAY_TIMER_LOOP 5
|
||||
|
||||
#define VREF_MV_BASE 1850
|
||||
|
||||
const char *mx23_lradc_adc_irq_names[] = {
|
||||
"mxs-lradc-channel0",
|
||||
"mxs-lradc-channel1",
|
||||
"mxs-lradc-channel2",
|
||||
"mxs-lradc-channel3",
|
||||
"mxs-lradc-channel4",
|
||||
"mxs-lradc-channel5",
|
||||
};
|
||||
|
||||
const char *mx28_lradc_adc_irq_names[] = {
|
||||
"mxs-lradc-thresh0",
|
||||
"mxs-lradc-thresh1",
|
||||
"mxs-lradc-channel0",
|
||||
"mxs-lradc-channel1",
|
||||
"mxs-lradc-channel2",
|
||||
"mxs-lradc-channel3",
|
||||
"mxs-lradc-channel4",
|
||||
"mxs-lradc-channel5",
|
||||
"mxs-lradc-button0",
|
||||
"mxs-lradc-button1",
|
||||
};
|
||||
|
||||
static const u32 mxs_lradc_adc_vref_mv[][LRADC_MAX_TOTAL_CHANS] = {
|
||||
[IMX23_LRADC] = {
|
||||
VREF_MV_BASE, /* CH0 */
|
||||
VREF_MV_BASE, /* CH1 */
|
||||
VREF_MV_BASE, /* CH2 */
|
||||
VREF_MV_BASE, /* CH3 */
|
||||
VREF_MV_BASE, /* CH4 */
|
||||
VREF_MV_BASE, /* CH5 */
|
||||
VREF_MV_BASE * 2, /* CH6 VDDIO */
|
||||
VREF_MV_BASE * 4, /* CH7 VBATT */
|
||||
VREF_MV_BASE, /* CH8 Temp sense 0 */
|
||||
VREF_MV_BASE, /* CH9 Temp sense 1 */
|
||||
VREF_MV_BASE, /* CH10 */
|
||||
VREF_MV_BASE, /* CH11 */
|
||||
VREF_MV_BASE, /* CH12 USB_DP */
|
||||
VREF_MV_BASE, /* CH13 USB_DN */
|
||||
VREF_MV_BASE, /* CH14 VBG */
|
||||
VREF_MV_BASE * 4, /* CH15 VDD5V */
|
||||
},
|
||||
[IMX28_LRADC] = {
|
||||
VREF_MV_BASE, /* CH0 */
|
||||
VREF_MV_BASE, /* CH1 */
|
||||
VREF_MV_BASE, /* CH2 */
|
||||
VREF_MV_BASE, /* CH3 */
|
||||
VREF_MV_BASE, /* CH4 */
|
||||
VREF_MV_BASE, /* CH5 */
|
||||
VREF_MV_BASE, /* CH6 */
|
||||
VREF_MV_BASE * 4, /* CH7 VBATT */
|
||||
VREF_MV_BASE, /* CH8 Temp sense 0 */
|
||||
VREF_MV_BASE, /* CH9 Temp sense 1 */
|
||||
VREF_MV_BASE * 2, /* CH10 VDDIO */
|
||||
VREF_MV_BASE, /* CH11 VTH */
|
||||
VREF_MV_BASE * 2, /* CH12 VDDA */
|
||||
VREF_MV_BASE, /* CH13 VDDD */
|
||||
VREF_MV_BASE, /* CH14 VBG */
|
||||
VREF_MV_BASE * 4, /* CH15 VDD5V */
|
||||
},
|
||||
};
|
||||
|
||||
enum mxs_lradc_divbytwo {
|
||||
MXS_LRADC_DIV_DISABLED = 0,
|
||||
MXS_LRADC_DIV_ENABLED,
|
||||
};
|
||||
|
||||
struct mxs_lradc_scale {
|
||||
unsigned int integer;
|
||||
unsigned int nano;
|
||||
};
|
||||
|
||||
struct mxs_lradc_adc {
|
||||
struct mxs_lradc *lradc;
|
||||
struct device *dev;
|
||||
|
||||
void __iomem *base;
|
||||
u32 buffer[10];
|
||||
struct iio_trigger *trig;
|
||||
struct completion completion;
|
||||
spinlock_t lock;
|
||||
|
||||
const u32 *vref_mv;
|
||||
struct mxs_lradc_scale scale_avail[LRADC_MAX_TOTAL_CHANS][2];
|
||||
unsigned long is_divided;
|
||||
};
|
||||
|
||||
|
||||
/* Raw I/O operations */
|
||||
static int mxs_lradc_adc_read_single(struct iio_dev *iio_dev, int chan,
|
||||
int *val)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio_dev);
|
||||
struct mxs_lradc *lradc = adc->lradc;
|
||||
int ret;
|
||||
|
||||
/*
|
||||
* See if there is no buffered operation in progress. If there is simply
|
||||
* bail out. This can be improved to support both buffered and raw IO at
|
||||
* the same time, yet the code becomes horribly complicated. Therefore I
|
||||
* applied KISS principle here.
|
||||
*/
|
||||
ret = iio_device_claim_direct_mode(iio_dev);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
reinit_completion(&adc->completion);
|
||||
|
||||
/*
|
||||
* No buffered operation in progress, map the channel and trigger it.
|
||||
* Virtual channel 0 is always used here as the others are always not
|
||||
* used if doing raw sampling.
|
||||
*/
|
||||
if (lradc->soc == IMX28_LRADC)
|
||||
writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
|
||||
adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
writel(0x1, adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/* Enable / disable the divider per requirement */
|
||||
if (test_bit(chan, &adc->is_divided))
|
||||
writel(1 << LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET,
|
||||
adc->base + LRADC_CTRL2 + STMP_OFFSET_REG_SET);
|
||||
else
|
||||
writel(1 << LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET,
|
||||
adc->base + LRADC_CTRL2 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/* Clean the slot's previous content, then set new one. */
|
||||
writel(LRADC_CTRL4_LRADCSELECT_MASK(0),
|
||||
adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
|
||||
writel(chan, adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
|
||||
|
||||
writel(0, adc->base + LRADC_CH(0));
|
||||
|
||||
/* Enable the IRQ and start sampling the channel. */
|
||||
writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
|
||||
adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
|
||||
writel(BIT(0), adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
|
||||
|
||||
/* Wait for completion on the channel, 1 second max. */
|
||||
ret = wait_for_completion_killable_timeout(&adc->completion, HZ);
|
||||
if (!ret)
|
||||
ret = -ETIMEDOUT;
|
||||
if (ret < 0)
|
||||
goto err;
|
||||
|
||||
/* Read the data. */
|
||||
*val = readl(adc->base + LRADC_CH(0)) & LRADC_CH_VALUE_MASK;
|
||||
ret = IIO_VAL_INT;
|
||||
|
||||
err:
|
||||
writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
|
||||
adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
iio_device_release_direct_mode(iio_dev);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_read_temp(struct iio_dev *iio_dev, int *val)
|
||||
{
|
||||
int ret, min, max;
|
||||
|
||||
ret = mxs_lradc_adc_read_single(iio_dev, 8, &min);
|
||||
if (ret != IIO_VAL_INT)
|
||||
return ret;
|
||||
|
||||
ret = mxs_lradc_adc_read_single(iio_dev, 9, &max);
|
||||
if (ret != IIO_VAL_INT)
|
||||
return ret;
|
||||
|
||||
*val = max - min;
|
||||
|
||||
return IIO_VAL_INT;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_read_raw(struct iio_dev *iio_dev,
|
||||
const struct iio_chan_spec *chan,
|
||||
int *val, int *val2, long m)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio_dev);
|
||||
|
||||
switch (m) {
|
||||
case IIO_CHAN_INFO_RAW:
|
||||
if (chan->type == IIO_TEMP)
|
||||
return mxs_lradc_adc_read_temp(iio_dev, val);
|
||||
|
||||
return mxs_lradc_adc_read_single(iio_dev, chan->channel, val);
|
||||
|
||||
case IIO_CHAN_INFO_SCALE:
|
||||
if (chan->type == IIO_TEMP) {
|
||||
/*
|
||||
* From the datasheet, we have to multiply by 1.012 and
|
||||
* divide by 4
|
||||
*/
|
||||
*val = 0;
|
||||
*val2 = 253000;
|
||||
return IIO_VAL_INT_PLUS_MICRO;
|
||||
}
|
||||
|
||||
*val = adc->vref_mv[chan->channel];
|
||||
*val2 = chan->scan_type.realbits -
|
||||
test_bit(chan->channel, &adc->is_divided);
|
||||
return IIO_VAL_FRACTIONAL_LOG2;
|
||||
|
||||
case IIO_CHAN_INFO_OFFSET:
|
||||
if (chan->type == IIO_TEMP) {
|
||||
/*
|
||||
* The calculated value from the ADC is in Kelvin, we
|
||||
* want Celsius for hwmon so the offset is -273.15
|
||||
* The offset is applied before scaling so it is
|
||||
* actually -213.15 * 4 / 1.012 = -1079.644268
|
||||
*/
|
||||
*val = -1079;
|
||||
*val2 = 644268;
|
||||
|
||||
return IIO_VAL_INT_PLUS_MICRO;
|
||||
}
|
||||
|
||||
return -EINVAL;
|
||||
|
||||
default:
|
||||
break;
|
||||
}
|
||||
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_write_raw(struct iio_dev *iio_dev,
|
||||
const struct iio_chan_spec *chan,
|
||||
int val, int val2, long m)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio_dev);
|
||||
struct mxs_lradc_scale *scale_avail =
|
||||
adc->scale_avail[chan->channel];
|
||||
int ret;
|
||||
|
||||
ret = iio_device_claim_direct_mode(iio_dev);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
switch (m) {
|
||||
case IIO_CHAN_INFO_SCALE:
|
||||
ret = -EINVAL;
|
||||
if (val == scale_avail[MXS_LRADC_DIV_DISABLED].integer &&
|
||||
val2 == scale_avail[MXS_LRADC_DIV_DISABLED].nano) {
|
||||
/* divider by two disabled */
|
||||
clear_bit(chan->channel, &adc->is_divided);
|
||||
ret = 0;
|
||||
} else if (val == scale_avail[MXS_LRADC_DIV_ENABLED].integer &&
|
||||
val2 == scale_avail[MXS_LRADC_DIV_ENABLED].nano) {
|
||||
/* divider by two enabled */
|
||||
set_bit(chan->channel, &adc->is_divided);
|
||||
ret = 0;
|
||||
}
|
||||
|
||||
break;
|
||||
default:
|
||||
ret = -EINVAL;
|
||||
break;
|
||||
}
|
||||
|
||||
iio_device_release_direct_mode(iio_dev);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_write_raw_get_fmt(struct iio_dev *iio_dev,
|
||||
const struct iio_chan_spec *chan,
|
||||
long m)
|
||||
{
|
||||
return IIO_VAL_INT_PLUS_NANO;
|
||||
}
|
||||
|
||||
static ssize_t mxs_lradc_adc_show_scale_avail(struct device *dev,
|
||||
struct device_attribute *attr,
|
||||
char *buf)
|
||||
{
|
||||
struct iio_dev *iio = dev_to_iio_dev(dev);
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
struct iio_dev_attr *iio_attr = to_iio_dev_attr(attr);
|
||||
int i, ch, len = 0;
|
||||
|
||||
ch = iio_attr->address;
|
||||
for (i = 0; i < ARRAY_SIZE(adc->scale_avail[ch]); i++)
|
||||
len += sprintf(buf + len, "%u.%09u ",
|
||||
adc->scale_avail[ch][i].integer,
|
||||
adc->scale_avail[ch][i].nano);
|
||||
|
||||
len += sprintf(buf + len, "\n");
|
||||
|
||||
return len;
|
||||
}
|
||||
|
||||
#define SHOW_SCALE_AVAILABLE_ATTR(ch)\
|
||||
IIO_DEVICE_ATTR(in_voltage##ch##_scale_available, 0444,\
|
||||
mxs_lradc_adc_show_scale_avail, NULL, ch)
|
||||
|
||||
SHOW_SCALE_AVAILABLE_ATTR(0);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(1);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(2);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(3);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(4);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(5);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(6);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(7);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(10);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(11);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(12);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(13);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(14);
|
||||
SHOW_SCALE_AVAILABLE_ATTR(15);
|
||||
|
||||
static struct attribute *mxs_lradc_adc_attributes[] = {
|
||||
&iio_dev_attr_in_voltage0_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage1_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage2_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage3_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage4_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage5_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage6_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage7_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage10_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage11_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage12_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage13_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage14_scale_available.dev_attr.attr,
|
||||
&iio_dev_attr_in_voltage15_scale_available.dev_attr.attr,
|
||||
NULL
|
||||
};
|
||||
|
||||
static const struct attribute_group mxs_lradc_adc_attribute_group = {
|
||||
.attrs = mxs_lradc_adc_attributes,
|
||||
};
|
||||
|
||||
static const struct iio_info mxs_lradc_adc_iio_info = {
|
||||
.driver_module = THIS_MODULE,
|
||||
.read_raw = mxs_lradc_adc_read_raw,
|
||||
.write_raw = mxs_lradc_adc_write_raw,
|
||||
.write_raw_get_fmt = mxs_lradc_adc_write_raw_get_fmt,
|
||||
.attrs = &mxs_lradc_adc_attribute_group,
|
||||
};
|
||||
|
||||
/* IRQ Handling */
|
||||
static irqreturn_t mxs_lradc_adc_handle_irq(int irq, void *data)
|
||||
{
|
||||
struct iio_dev *iio = data;
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
struct mxs_lradc *lradc = adc->lradc;
|
||||
unsigned long reg = readl(adc->base + LRADC_CTRL1);
|
||||
unsigned long flags;
|
||||
|
||||
if (!(reg & mxs_lradc_irq_mask(lradc)))
|
||||
return IRQ_NONE;
|
||||
|
||||
if (iio_buffer_enabled(iio)) {
|
||||
if (reg & lradc->buffer_vchans) {
|
||||
spin_lock_irqsave(&adc->lock, flags);
|
||||
iio_trigger_poll(iio->trig);
|
||||
spin_unlock_irqrestore(&adc->lock, flags);
|
||||
}
|
||||
} else if (reg & LRADC_CTRL1_LRADC_IRQ(0)) {
|
||||
complete(&adc->completion);
|
||||
}
|
||||
|
||||
writel(reg & mxs_lradc_irq_mask(lradc),
|
||||
adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
|
||||
/* Trigger handling */
|
||||
static irqreturn_t mxs_lradc_adc_trigger_handler(int irq, void *p)
|
||||
{
|
||||
struct iio_poll_func *pf = p;
|
||||
struct iio_dev *iio = pf->indio_dev;
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
const u32 chan_value = LRADC_CH_ACCUMULATE |
|
||||
((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
|
||||
unsigned int i, j = 0;
|
||||
|
||||
for_each_set_bit(i, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
|
||||
adc->buffer[j] = readl(adc->base + LRADC_CH(j));
|
||||
writel(chan_value, adc->base + LRADC_CH(j));
|
||||
adc->buffer[j] &= LRADC_CH_VALUE_MASK;
|
||||
adc->buffer[j] /= LRADC_DELAY_TIMER_LOOP;
|
||||
j++;
|
||||
}
|
||||
|
||||
iio_push_to_buffers_with_timestamp(iio, adc->buffer, pf->timestamp);
|
||||
|
||||
iio_trigger_notify_done(iio->trig);
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_configure_trigger(struct iio_trigger *trig, bool state)
|
||||
{
|
||||
struct iio_dev *iio = iio_trigger_get_drvdata(trig);
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
const u32 st = state ? STMP_OFFSET_REG_SET : STMP_OFFSET_REG_CLR;
|
||||
|
||||
writel(LRADC_DELAY_KICK, adc->base + (LRADC_DELAY(0) + st));
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct iio_trigger_ops mxs_lradc_adc_trigger_ops = {
|
||||
.owner = THIS_MODULE,
|
||||
.set_trigger_state = &mxs_lradc_adc_configure_trigger,
|
||||
};
|
||||
|
||||
static int mxs_lradc_adc_trigger_init(struct iio_dev *iio)
|
||||
{
|
||||
int ret;
|
||||
struct iio_trigger *trig;
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
|
||||
trig = devm_iio_trigger_alloc(&iio->dev, "%s-dev%i", iio->name,
|
||||
iio->id);
|
||||
|
||||
trig->dev.parent = adc->dev;
|
||||
iio_trigger_set_drvdata(trig, iio);
|
||||
trig->ops = &mxs_lradc_adc_trigger_ops;
|
||||
|
||||
ret = iio_trigger_register(trig);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
adc->trig = trig;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void mxs_lradc_adc_trigger_remove(struct iio_dev *iio)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
|
||||
iio_trigger_unregister(adc->trig);
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_buffer_preenable(struct iio_dev *iio)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
struct mxs_lradc *lradc = adc->lradc;
|
||||
int chan, ofs = 0;
|
||||
unsigned long enable = 0;
|
||||
u32 ctrl4_set = 0;
|
||||
u32 ctrl4_clr = 0;
|
||||
u32 ctrl1_irq = 0;
|
||||
const u32 chan_value = LRADC_CH_ACCUMULATE |
|
||||
((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
|
||||
|
||||
if (lradc->soc == IMX28_LRADC)
|
||||
writel(lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
|
||||
adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
writel(lradc->buffer_vchans,
|
||||
adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
|
||||
ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
|
||||
ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
|
||||
ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
|
||||
writel(chan_value, adc->base + LRADC_CH(ofs));
|
||||
bitmap_set(&enable, ofs, 1);
|
||||
ofs++;
|
||||
}
|
||||
|
||||
writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
|
||||
adc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
|
||||
writel(ctrl4_clr, adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
|
||||
writel(ctrl4_set, adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
|
||||
writel(ctrl1_irq, adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
|
||||
writel(enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
|
||||
adc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_SET);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_buffer_postdisable(struct iio_dev *iio)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
struct mxs_lradc *lradc = adc->lradc;
|
||||
|
||||
writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
|
||||
adc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
|
||||
|
||||
writel(lradc->buffer_vchans,
|
||||
adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
if (lradc->soc == IMX28_LRADC)
|
||||
writel(lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
|
||||
adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static bool mxs_lradc_adc_validate_scan_mask(struct iio_dev *iio,
|
||||
const unsigned long *mask)
|
||||
{
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
struct mxs_lradc *lradc = adc->lradc;
|
||||
const int map_chans = bitmap_weight(mask, LRADC_MAX_TOTAL_CHANS);
|
||||
int rsvd_chans = 0;
|
||||
unsigned long rsvd_mask = 0;
|
||||
|
||||
if (lradc->use_touchbutton)
|
||||
rsvd_mask |= CHAN_MASK_TOUCHBUTTON;
|
||||
if (lradc->touchscreen_wire == MXS_LRADC_TOUCHSCREEN_4WIRE)
|
||||
rsvd_mask |= CHAN_MASK_TOUCHSCREEN_4WIRE;
|
||||
if (lradc->touchscreen_wire == MXS_LRADC_TOUCHSCREEN_5WIRE)
|
||||
rsvd_mask |= CHAN_MASK_TOUCHSCREEN_5WIRE;
|
||||
|
||||
if (lradc->use_touchbutton)
|
||||
rsvd_chans++;
|
||||
if (lradc->touchscreen_wire)
|
||||
rsvd_chans += 2;
|
||||
|
||||
/* Test for attempts to map channels with special mode of operation. */
|
||||
if (bitmap_intersects(mask, &rsvd_mask, LRADC_MAX_TOTAL_CHANS))
|
||||
return false;
|
||||
|
||||
/* Test for attempts to map more channels then available slots. */
|
||||
if (map_chans + rsvd_chans > LRADC_MAX_MAPPED_CHANS)
|
||||
return false;
|
||||
|
||||
return true;
|
||||
}
|
||||
|
||||
static const struct iio_buffer_setup_ops mxs_lradc_adc_buffer_ops = {
|
||||
.preenable = &mxs_lradc_adc_buffer_preenable,
|
||||
.postenable = &iio_triggered_buffer_postenable,
|
||||
.predisable = &iio_triggered_buffer_predisable,
|
||||
.postdisable = &mxs_lradc_adc_buffer_postdisable,
|
||||
.validate_scan_mask = &mxs_lradc_adc_validate_scan_mask,
|
||||
};
|
||||
|
||||
/* Driver initialization */
|
||||
#define MXS_ADC_CHAN(idx, chan_type, name) { \
|
||||
.type = (chan_type), \
|
||||
.indexed = 1, \
|
||||
.scan_index = (idx), \
|
||||
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
|
||||
BIT(IIO_CHAN_INFO_SCALE), \
|
||||
.channel = (idx), \
|
||||
.address = (idx), \
|
||||
.scan_type = { \
|
||||
.sign = 'u', \
|
||||
.realbits = LRADC_RESOLUTION, \
|
||||
.storagebits = 32, \
|
||||
}, \
|
||||
.datasheet_name = (name), \
|
||||
}
|
||||
|
||||
static const struct iio_chan_spec mx23_lradc_chan_spec[] = {
|
||||
MXS_ADC_CHAN(0, IIO_VOLTAGE, "LRADC0"),
|
||||
MXS_ADC_CHAN(1, IIO_VOLTAGE, "LRADC1"),
|
||||
MXS_ADC_CHAN(2, IIO_VOLTAGE, "LRADC2"),
|
||||
MXS_ADC_CHAN(3, IIO_VOLTAGE, "LRADC3"),
|
||||
MXS_ADC_CHAN(4, IIO_VOLTAGE, "LRADC4"),
|
||||
MXS_ADC_CHAN(5, IIO_VOLTAGE, "LRADC5"),
|
||||
MXS_ADC_CHAN(6, IIO_VOLTAGE, "VDDIO"),
|
||||
MXS_ADC_CHAN(7, IIO_VOLTAGE, "VBATT"),
|
||||
/* Combined Temperature sensors */
|
||||
{
|
||||
.type = IIO_TEMP,
|
||||
.indexed = 1,
|
||||
.scan_index = 8,
|
||||
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
|
||||
BIT(IIO_CHAN_INFO_OFFSET) |
|
||||
BIT(IIO_CHAN_INFO_SCALE),
|
||||
.channel = 8,
|
||||
.scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,},
|
||||
.datasheet_name = "TEMP_DIE",
|
||||
},
|
||||
/* Hidden channel to keep indexes */
|
||||
{
|
||||
.type = IIO_TEMP,
|
||||
.indexed = 1,
|
||||
.scan_index = -1,
|
||||
.channel = 9,
|
||||
},
|
||||
MXS_ADC_CHAN(10, IIO_VOLTAGE, NULL),
|
||||
MXS_ADC_CHAN(11, IIO_VOLTAGE, NULL),
|
||||
MXS_ADC_CHAN(12, IIO_VOLTAGE, "USB_DP"),
|
||||
MXS_ADC_CHAN(13, IIO_VOLTAGE, "USB_DN"),
|
||||
MXS_ADC_CHAN(14, IIO_VOLTAGE, "VBG"),
|
||||
MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
|
||||
};
|
||||
|
||||
static const struct iio_chan_spec mx28_lradc_chan_spec[] = {
|
||||
MXS_ADC_CHAN(0, IIO_VOLTAGE, "LRADC0"),
|
||||
MXS_ADC_CHAN(1, IIO_VOLTAGE, "LRADC1"),
|
||||
MXS_ADC_CHAN(2, IIO_VOLTAGE, "LRADC2"),
|
||||
MXS_ADC_CHAN(3, IIO_VOLTAGE, "LRADC3"),
|
||||
MXS_ADC_CHAN(4, IIO_VOLTAGE, "LRADC4"),
|
||||
MXS_ADC_CHAN(5, IIO_VOLTAGE, "LRADC5"),
|
||||
MXS_ADC_CHAN(6, IIO_VOLTAGE, "LRADC6"),
|
||||
MXS_ADC_CHAN(7, IIO_VOLTAGE, "VBATT"),
|
||||
/* Combined Temperature sensors */
|
||||
{
|
||||
.type = IIO_TEMP,
|
||||
.indexed = 1,
|
||||
.scan_index = 8,
|
||||
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
|
||||
BIT(IIO_CHAN_INFO_OFFSET) |
|
||||
BIT(IIO_CHAN_INFO_SCALE),
|
||||
.channel = 8,
|
||||
.scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,},
|
||||
.datasheet_name = "TEMP_DIE",
|
||||
},
|
||||
/* Hidden channel to keep indexes */
|
||||
{
|
||||
.type = IIO_TEMP,
|
||||
.indexed = 1,
|
||||
.scan_index = -1,
|
||||
.channel = 9,
|
||||
},
|
||||
MXS_ADC_CHAN(10, IIO_VOLTAGE, "VDDIO"),
|
||||
MXS_ADC_CHAN(11, IIO_VOLTAGE, "VTH"),
|
||||
MXS_ADC_CHAN(12, IIO_VOLTAGE, "VDDA"),
|
||||
MXS_ADC_CHAN(13, IIO_VOLTAGE, "VDDD"),
|
||||
MXS_ADC_CHAN(14, IIO_VOLTAGE, "VBG"),
|
||||
MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
|
||||
};
|
||||
|
||||
static void mxs_lradc_adc_hw_init(struct mxs_lradc_adc *adc)
|
||||
{
|
||||
/* The ADC always uses DELAY CHANNEL 0. */
|
||||
const u32 adc_cfg =
|
||||
(1 << (LRADC_DELAY_TRIGGER_DELAYS_OFFSET + 0)) |
|
||||
(LRADC_DELAY_TIMER_PER << LRADC_DELAY_DELAY_OFFSET);
|
||||
|
||||
/* Configure DELAY CHANNEL 0 for generic ADC sampling. */
|
||||
writel(adc_cfg, adc->base + LRADC_DELAY(0));
|
||||
|
||||
/*
|
||||
* Start internal temperature sensing by clearing bit
|
||||
* HW_LRADC_CTRL2_TEMPSENSE_PWD. This bit can be left cleared
|
||||
* after power up.
|
||||
*/
|
||||
writel(0, adc->base + LRADC_CTRL2);
|
||||
}
|
||||
|
||||
static void mxs_lradc_adc_hw_stop(struct mxs_lradc_adc *adc)
|
||||
{
|
||||
writel(0, adc->base + LRADC_DELAY(0));
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct device *dev = &pdev->dev;
|
||||
struct mxs_lradc *lradc = dev_get_drvdata(dev->parent);
|
||||
struct mxs_lradc_adc *adc;
|
||||
struct iio_dev *iio;
|
||||
struct resource *iores;
|
||||
int ret, irq, virq, i, s, n;
|
||||
u64 scale_uv;
|
||||
const char **irq_name;
|
||||
|
||||
/* Allocate the IIO device. */
|
||||
iio = devm_iio_device_alloc(dev, sizeof(*adc));
|
||||
if (!iio) {
|
||||
dev_err(dev, "Failed to allocate IIO device\n");
|
||||
return -ENOMEM;
|
||||
}
|
||||
|
||||
adc = iio_priv(iio);
|
||||
adc->lradc = lradc;
|
||||
adc->dev = dev;
|
||||
|
||||
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
adc->base = devm_ioremap(dev, iores->start, resource_size(iores));
|
||||
if (IS_ERR(adc->base))
|
||||
return PTR_ERR(adc->base);
|
||||
|
||||
init_completion(&adc->completion);
|
||||
spin_lock_init(&adc->lock);
|
||||
|
||||
platform_set_drvdata(pdev, iio);
|
||||
|
||||
iio->name = pdev->name;
|
||||
iio->dev.parent = dev;
|
||||
iio->dev.of_node = dev->parent->of_node;
|
||||
iio->info = &mxs_lradc_adc_iio_info;
|
||||
iio->modes = INDIO_DIRECT_MODE;
|
||||
iio->masklength = LRADC_MAX_TOTAL_CHANS;
|
||||
|
||||
if (lradc->soc == IMX23_LRADC) {
|
||||
iio->channels = mx23_lradc_chan_spec;
|
||||
iio->num_channels = ARRAY_SIZE(mx23_lradc_chan_spec);
|
||||
irq_name = mx23_lradc_adc_irq_names;
|
||||
n = ARRAY_SIZE(mx23_lradc_adc_irq_names);
|
||||
} else {
|
||||
iio->channels = mx28_lradc_chan_spec;
|
||||
iio->num_channels = ARRAY_SIZE(mx28_lradc_chan_spec);
|
||||
irq_name = mx28_lradc_adc_irq_names;
|
||||
n = ARRAY_SIZE(mx28_lradc_adc_irq_names);
|
||||
}
|
||||
|
||||
ret = stmp_reset_block(adc->base);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
for (i = 0; i < n; i++) {
|
||||
irq = platform_get_irq_byname(pdev, irq_name[i]);
|
||||
if (irq < 0)
|
||||
return irq;
|
||||
|
||||
virq = irq_of_parse_and_map(dev->parent->of_node, irq);
|
||||
|
||||
ret = devm_request_irq(dev, virq, mxs_lradc_adc_handle_irq,
|
||||
0, irq_name[i], iio);
|
||||
if (ret)
|
||||
return ret;
|
||||
}
|
||||
|
||||
ret = mxs_lradc_adc_trigger_init(iio);
|
||||
if (ret)
|
||||
goto err_trig;
|
||||
|
||||
ret = iio_triggered_buffer_setup(iio, &iio_pollfunc_store_time,
|
||||
&mxs_lradc_adc_trigger_handler,
|
||||
&mxs_lradc_adc_buffer_ops);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
adc->vref_mv = mxs_lradc_adc_vref_mv[lradc->soc];
|
||||
|
||||
/* Populate available ADC input ranges */
|
||||
for (i = 0; i < LRADC_MAX_TOTAL_CHANS; i++) {
|
||||
for (s = 0; s < ARRAY_SIZE(adc->scale_avail[i]); s++) {
|
||||
/*
|
||||
* [s=0] = optional divider by two disabled (default)
|
||||
* [s=1] = optional divider by two enabled
|
||||
*
|
||||
* The scale is calculated by doing:
|
||||
* Vref >> (realbits - s)
|
||||
* which multiplies by two on the second component
|
||||
* of the array.
|
||||
*/
|
||||
scale_uv = ((u64)adc->vref_mv[i] * 100000000) >>
|
||||
(LRADC_RESOLUTION - s);
|
||||
adc->scale_avail[i][s].nano =
|
||||
do_div(scale_uv, 100000000) * 10;
|
||||
adc->scale_avail[i][s].integer = scale_uv;
|
||||
}
|
||||
}
|
||||
|
||||
/* Configure the hardware. */
|
||||
mxs_lradc_adc_hw_init(adc);
|
||||
|
||||
/* Register IIO device. */
|
||||
ret = iio_device_register(iio);
|
||||
if (ret) {
|
||||
dev_err(dev, "Failed to register IIO device\n");
|
||||
goto err_dev;
|
||||
}
|
||||
|
||||
return 0;
|
||||
|
||||
err_dev:
|
||||
mxs_lradc_adc_hw_stop(adc);
|
||||
mxs_lradc_adc_trigger_remove(iio);
|
||||
err_trig:
|
||||
iio_triggered_buffer_cleanup(iio);
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int mxs_lradc_adc_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct iio_dev *iio = platform_get_drvdata(pdev);
|
||||
struct mxs_lradc_adc *adc = iio_priv(iio);
|
||||
|
||||
iio_device_unregister(iio);
|
||||
mxs_lradc_adc_hw_stop(adc);
|
||||
mxs_lradc_adc_trigger_remove(iio);
|
||||
iio_triggered_buffer_cleanup(iio);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct platform_driver mxs_lradc_adc_driver = {
|
||||
.driver = {
|
||||
.name = "mxs-lradc-adc",
|
||||
},
|
||||
.probe = mxs_lradc_adc_probe,
|
||||
.remove = mxs_lradc_adc_remove,
|
||||
};
|
||||
module_platform_driver(mxs_lradc_adc_driver);
|
||||
|
||||
MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
|
||||
MODULE_DESCRIPTION("Freescale MXS LRADC driver general purpose ADC driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_ALIAS("platform:mxs-lradc-adc");
|
||||
File diff suppressed because it is too large
Load Diff
|
|
@ -316,6 +316,16 @@ config INPUT_COBALT_BTNS
|
|||
To compile this driver as a module, choose M here: the
|
||||
module will be called cobalt_btns.
|
||||
|
||||
config INPUT_CPCAP_PWRBUTTON
|
||||
tristate "CPCAP OnKey"
|
||||
depends on MFD_CPCAP
|
||||
help
|
||||
Say Y here if you want to enable power key reporting via the
|
||||
Motorola CPCAP chip.
|
||||
|
||||
To compile this driver as a module, choose M here. The module will
|
||||
be called cpcap-pwrbutton.
|
||||
|
||||
config INPUT_WISTRON_BTNS
|
||||
tristate "x86 Wistron laptop button interface"
|
||||
depends on X86_32
|
||||
|
|
|
|||
|
|
@ -24,6 +24,7 @@ obj-$(CONFIG_INPUT_CM109) += cm109.o
|
|||
obj-$(CONFIG_INPUT_CMA3000) += cma3000_d0x.o
|
||||
obj-$(CONFIG_INPUT_CMA3000_I2C) += cma3000_d0x_i2c.o
|
||||
obj-$(CONFIG_INPUT_COBALT_BTNS) += cobalt_btns.o
|
||||
obj-$(CONFIG_INPUT_CPCAP_PWRBUTTON) += cpcap-pwrbutton.o
|
||||
obj-$(CONFIG_INPUT_DA9052_ONKEY) += da9052_onkey.o
|
||||
obj-$(CONFIG_INPUT_DA9055_ONKEY) += da9055_onkey.o
|
||||
obj-$(CONFIG_INPUT_DA9063_ONKEY) += da9063_onkey.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,117 @@
|
|||
/**
|
||||
* CPCAP Power Button Input Driver
|
||||
*
|
||||
* Copyright (C) 2017 Sebastian Reichel <sre@kernel.org>
|
||||
*
|
||||
* This file is subject to the terms and conditions of the GNU General
|
||||
* Public License. See the file "COPYING" in the main directory of this
|
||||
* archive for more details.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/errno.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/mfd/motorola-cpcap.h>
|
||||
|
||||
#define CPCAP_IRQ_ON 23
|
||||
#define CPCAP_IRQ_ON_BITMASK (1 << (CPCAP_IRQ_ON % 16))
|
||||
|
||||
struct cpcap_power_button {
|
||||
struct regmap *regmap;
|
||||
struct input_dev *idev;
|
||||
struct device *dev;
|
||||
};
|
||||
|
||||
static irqreturn_t powerbutton_irq(int irq, void *_button)
|
||||
{
|
||||
struct cpcap_power_button *button = _button;
|
||||
int val;
|
||||
|
||||
val = cpcap_sense_virq(button->regmap, irq);
|
||||
if (val < 0) {
|
||||
dev_err(button->dev, "irq read failed: %d", val);
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
pm_wakeup_event(button->dev, 0);
|
||||
input_report_key(button->idev, KEY_POWER, val);
|
||||
input_sync(button->idev);
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int cpcap_power_button_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct cpcap_power_button *button;
|
||||
int irq = platform_get_irq(pdev, 0);
|
||||
int err;
|
||||
|
||||
button = devm_kmalloc(&pdev->dev, sizeof(*button), GFP_KERNEL);
|
||||
if (!button)
|
||||
return -ENOMEM;
|
||||
|
||||
button->idev = devm_input_allocate_device(&pdev->dev);
|
||||
if (!button->idev)
|
||||
return -ENOMEM;
|
||||
|
||||
button->regmap = dev_get_regmap(pdev->dev.parent, NULL);
|
||||
if (!button->regmap)
|
||||
return -ENODEV;
|
||||
|
||||
button->dev = &pdev->dev;
|
||||
|
||||
button->idev->name = "cpcap-pwrbutton";
|
||||
button->idev->phys = "cpcap-pwrbutton/input0";
|
||||
button->idev->dev.parent = button->dev;
|
||||
input_set_capability(button->idev, EV_KEY, KEY_POWER);
|
||||
|
||||
err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
|
||||
powerbutton_irq, IRQF_ONESHOT, "cpcap_pwrbutton", button);
|
||||
if (err < 0) {
|
||||
dev_err(&pdev->dev, "IRQ request failed: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
err = input_register_device(button->idev);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "Input register failed: %d\n", err);
|
||||
return err;
|
||||
}
|
||||
|
||||
device_init_wakeup(&pdev->dev, true);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_OF
|
||||
static const struct of_device_id cpcap_pwrbutton_dt_match_table[] = {
|
||||
{ .compatible = "motorola,cpcap-pwrbutton" },
|
||||
{},
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, cpcap_pwrbutton_dt_match_table);
|
||||
#endif
|
||||
|
||||
static struct platform_driver cpcap_power_button_driver = {
|
||||
.probe = cpcap_power_button_probe,
|
||||
.driver = {
|
||||
.name = "cpcap-pwrbutton",
|
||||
.of_match_table = of_match_ptr(cpcap_pwrbutton_dt_match_table),
|
||||
},
|
||||
};
|
||||
module_platform_driver(cpcap_power_button_driver);
|
||||
|
||||
MODULE_ALIAS("platform:cpcap-pwrbutton");
|
||||
MODULE_DESCRIPTION("CPCAP Power Button");
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_AUTHOR("Sebastian Reichel <sre@kernel.org>");
|
||||
|
|
@ -829,6 +829,16 @@ config TOUCHSCREEN_USB_COMPOSITE
|
|||
To compile this driver as a module, choose M here: the
|
||||
module will be called usbtouchscreen.
|
||||
|
||||
config TOUCHSCREEN_MXS_LRADC
|
||||
tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
|
||||
depends on MFD_MXS_LRADC
|
||||
help
|
||||
Say Y here if you have a touchscreen connected to the low-resolution
|
||||
analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
|
||||
|
||||
To compile this driver as a module, choose M here: the module will be
|
||||
called mxs-lradc-ts.
|
||||
|
||||
config TOUCHSCREEN_MX25
|
||||
tristate "Freescale i.MX25 touchscreen input driver"
|
||||
depends on MFD_MX25_TSADC
|
||||
|
|
|
|||
|
|
@ -45,6 +45,7 @@ obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
|
|||
obj-$(CONFIG_TOUCHSCREEN_IPROC) += bcm_iproc_tsc.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_MXS_LRADC) += mxs-lradc-ts.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
|
||||
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,714 @@
|
|||
/*
|
||||
* Freescale MXS LRADC touchscreen driver
|
||||
*
|
||||
* Copyright (c) 2012 DENX Software Engineering, GmbH.
|
||||
* Copyright (c) 2017 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* Authors:
|
||||
* Marek Vasut <marex@denx.de>
|
||||
* Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/device.h>
|
||||
#include <linux/err.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/mfd/core.h>
|
||||
#include <linux/mfd/mxs-lradc.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_irq.h>
|
||||
#include <linux/platform_device.h>
|
||||
|
||||
const char *mxs_lradc_ts_irq_names[] = {
|
||||
"mxs-lradc-touchscreen",
|
||||
"mxs-lradc-channel6",
|
||||
"mxs-lradc-channel7",
|
||||
};
|
||||
|
||||
/*
|
||||
* Touchscreen handling
|
||||
*/
|
||||
enum mxs_lradc_ts_plate {
|
||||
LRADC_TOUCH = 0,
|
||||
LRADC_SAMPLE_X,
|
||||
LRADC_SAMPLE_Y,
|
||||
LRADC_SAMPLE_PRESSURE,
|
||||
LRADC_SAMPLE_VALID,
|
||||
};
|
||||
|
||||
struct mxs_lradc_ts {
|
||||
struct mxs_lradc *lradc;
|
||||
struct device *dev;
|
||||
|
||||
void __iomem *base;
|
||||
/*
|
||||
* When the touchscreen is enabled, we give it two private virtual
|
||||
* channels: #6 and #7. This means that only 6 virtual channels (instead
|
||||
* of 8) will be available for buffered capture.
|
||||
*/
|
||||
#define TOUCHSCREEN_VCHANNEL1 7
|
||||
#define TOUCHSCREEN_VCHANNEL2 6
|
||||
|
||||
struct input_dev *ts_input;
|
||||
|
||||
enum mxs_lradc_ts_plate cur_plate; /* state machine */
|
||||
bool ts_valid;
|
||||
unsigned int ts_x_pos;
|
||||
unsigned int ts_y_pos;
|
||||
unsigned int ts_pressure;
|
||||
|
||||
/* handle touchscreen's physical behaviour */
|
||||
/* samples per coordinate */
|
||||
unsigned int over_sample_cnt;
|
||||
/* time clocks between samples */
|
||||
unsigned int over_sample_delay;
|
||||
/* time in clocks to wait after the plates where switched */
|
||||
unsigned int settling_delay;
|
||||
spinlock_t lock;
|
||||
};
|
||||
|
||||
struct state_info {
|
||||
u32 mask;
|
||||
u32 bit;
|
||||
u32 x_plate;
|
||||
u32 y_plate;
|
||||
u32 pressure;
|
||||
};
|
||||
|
||||
static struct state_info info[] = {
|
||||
{LRADC_CTRL0_MX23_PLATE_MASK, LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE,
|
||||
LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM,
|
||||
LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM,
|
||||
LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM},
|
||||
{LRADC_CTRL0_MX28_PLATE_MASK, LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
|
||||
LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW,
|
||||
LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW,
|
||||
LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW}
|
||||
};
|
||||
|
||||
static bool mxs_lradc_check_touch_event(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
return !!(readl(ts->base + LRADC_STATUS) &
|
||||
LRADC_STATUS_TOUCH_DETECT_RAW);
|
||||
}
|
||||
|
||||
static void mxs_lradc_map_ts_channel(struct mxs_lradc_ts *ts, unsigned int vch,
|
||||
unsigned int ch)
|
||||
{
|
||||
writel(LRADC_CTRL4_LRADCSELECT_MASK(vch),
|
||||
ts->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
|
||||
writel(LRADC_CTRL4_LRADCSELECT(vch, ch),
|
||||
ts->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
|
||||
}
|
||||
|
||||
static void mxs_lradc_setup_ts_channel(struct mxs_lradc_ts *ts, unsigned int ch)
|
||||
{
|
||||
/*
|
||||
* prepare for oversampling conversion
|
||||
*
|
||||
* from the datasheet:
|
||||
* "The ACCUMULATE bit in the appropriate channel register
|
||||
* HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
|
||||
* otherwise, the IRQs will not fire."
|
||||
*/
|
||||
writel(LRADC_CH_ACCUMULATE |
|
||||
LRADC_CH_NUM_SAMPLES(ts->over_sample_cnt - 1),
|
||||
ts->base + LRADC_CH(ch));
|
||||
|
||||
/* from the datasheet:
|
||||
* "Software must clear this register in preparation for a
|
||||
* multi-cycle accumulation.
|
||||
*/
|
||||
writel(LRADC_CH_VALUE_MASK,
|
||||
ts->base + LRADC_CH(ch) + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/*
|
||||
* prepare the delay/loop unit according to the oversampling count
|
||||
*
|
||||
* from the datasheet:
|
||||
* "The DELAY fields in HW_LRADC_DELAY0, HW_LRADC_DELAY1,
|
||||
* HW_LRADC_DELAY2, and HW_LRADC_DELAY3 must be non-zero; otherwise,
|
||||
* the LRADC will not trigger the delay group."
|
||||
*/
|
||||
writel(LRADC_DELAY_TRIGGER(1 << ch) | LRADC_DELAY_TRIGGER_DELAYS(0) |
|
||||
LRADC_DELAY_LOOP(ts->over_sample_cnt - 1) |
|
||||
LRADC_DELAY_DELAY(ts->over_sample_delay - 1),
|
||||
ts->base + LRADC_DELAY(3));
|
||||
|
||||
writel(LRADC_CTRL1_LRADC_IRQ(ch),
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/*
|
||||
* after changing the touchscreen plates setting
|
||||
* the signals need some initial time to settle. Start the
|
||||
* SoC's delay unit and start the conversion later
|
||||
* and automatically.
|
||||
*/
|
||||
writel(LRADC_DELAY_TRIGGER(0) | LRADC_DELAY_TRIGGER_DELAYS(BIT(3)) |
|
||||
LRADC_DELAY_KICK | LRADC_DELAY_DELAY(ts->settling_delay),
|
||||
ts->base + LRADC_DELAY(2));
|
||||
}
|
||||
|
||||
/*
|
||||
* Pressure detection is special:
|
||||
* We want to do both required measurements for the pressure detection in
|
||||
* one turn. Use the hardware features to chain both conversions and let the
|
||||
* hardware report one interrupt if both conversions are done
|
||||
*/
|
||||
static void mxs_lradc_setup_ts_pressure(struct mxs_lradc_ts *ts,
|
||||
unsigned int ch1, unsigned int ch2)
|
||||
{
|
||||
u32 reg;
|
||||
|
||||
/*
|
||||
* prepare for oversampling conversion
|
||||
*
|
||||
* from the datasheet:
|
||||
* "The ACCUMULATE bit in the appropriate channel register
|
||||
* HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
|
||||
* otherwise, the IRQs will not fire."
|
||||
*/
|
||||
reg = LRADC_CH_ACCUMULATE |
|
||||
LRADC_CH_NUM_SAMPLES(ts->over_sample_cnt - 1);
|
||||
writel(reg, ts->base + LRADC_CH(ch1));
|
||||
writel(reg, ts->base + LRADC_CH(ch2));
|
||||
|
||||
/* from the datasheet:
|
||||
* "Software must clear this register in preparation for a
|
||||
* multi-cycle accumulation.
|
||||
*/
|
||||
writel(LRADC_CH_VALUE_MASK,
|
||||
ts->base + LRADC_CH(ch1) + STMP_OFFSET_REG_CLR);
|
||||
writel(LRADC_CH_VALUE_MASK,
|
||||
ts->base + LRADC_CH(ch2) + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/* prepare the delay/loop unit according to the oversampling count */
|
||||
writel(LRADC_DELAY_TRIGGER(1 << ch1) | LRADC_DELAY_TRIGGER(1 << ch2) |
|
||||
LRADC_DELAY_TRIGGER_DELAYS(0) |
|
||||
LRADC_DELAY_LOOP(ts->over_sample_cnt - 1) |
|
||||
LRADC_DELAY_DELAY(ts->over_sample_delay - 1),
|
||||
ts->base + LRADC_DELAY(3));
|
||||
|
||||
writel(LRADC_CTRL1_LRADC_IRQ(ch2),
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/*
|
||||
* after changing the touchscreen plates setting
|
||||
* the signals need some initial time to settle. Start the
|
||||
* SoC's delay unit and start the conversion later
|
||||
* and automatically.
|
||||
*/
|
||||
writel(LRADC_DELAY_TRIGGER(0) | LRADC_DELAY_TRIGGER_DELAYS(BIT(3)) |
|
||||
LRADC_DELAY_KICK | LRADC_DELAY_DELAY(ts->settling_delay),
|
||||
ts->base + LRADC_DELAY(2));
|
||||
}
|
||||
|
||||
static unsigned int mxs_lradc_ts_read_raw_channel(struct mxs_lradc_ts *ts,
|
||||
unsigned int channel)
|
||||
{
|
||||
u32 reg;
|
||||
unsigned int num_samples, val;
|
||||
|
||||
reg = readl(ts->base + LRADC_CH(channel));
|
||||
if (reg & LRADC_CH_ACCUMULATE)
|
||||
num_samples = ts->over_sample_cnt;
|
||||
else
|
||||
num_samples = 1;
|
||||
|
||||
val = (reg & LRADC_CH_VALUE_MASK) >> LRADC_CH_VALUE_OFFSET;
|
||||
return val / num_samples;
|
||||
}
|
||||
|
||||
static unsigned int mxs_lradc_read_ts_pressure(struct mxs_lradc_ts *ts,
|
||||
unsigned int ch1, unsigned int ch2)
|
||||
{
|
||||
u32 reg, mask;
|
||||
unsigned int pressure, m1, m2;
|
||||
|
||||
mask = LRADC_CTRL1_LRADC_IRQ(ch1) | LRADC_CTRL1_LRADC_IRQ(ch2);
|
||||
reg = readl(ts->base + LRADC_CTRL1) & mask;
|
||||
|
||||
while (reg != mask) {
|
||||
reg = readl(ts->base + LRADC_CTRL1) & mask;
|
||||
dev_dbg(ts->dev, "One channel is still busy: %X\n", reg);
|
||||
}
|
||||
|
||||
m1 = mxs_lradc_ts_read_raw_channel(ts, ch1);
|
||||
m2 = mxs_lradc_ts_read_raw_channel(ts, ch2);
|
||||
|
||||
if (m2 == 0) {
|
||||
dev_warn(ts->dev, "Cannot calculate pressure\n");
|
||||
return 1 << (LRADC_RESOLUTION - 1);
|
||||
}
|
||||
|
||||
/* simply scale the value from 0 ... max ADC resolution */
|
||||
pressure = m1;
|
||||
pressure *= (1 << LRADC_RESOLUTION);
|
||||
pressure /= m2;
|
||||
|
||||
dev_dbg(ts->dev, "Pressure = %u\n", pressure);
|
||||
return pressure;
|
||||
}
|
||||
|
||||
#define TS_CH_XP 2
|
||||
#define TS_CH_YP 3
|
||||
#define TS_CH_XM 4
|
||||
#define TS_CH_YM 5
|
||||
|
||||
/*
|
||||
* YP(open)--+-------------+
|
||||
* | |--+
|
||||
* | | |
|
||||
* YM(-)--+-------------+ |
|
||||
* +--------------+
|
||||
* | |
|
||||
* XP(weak+) XM(open)
|
||||
*
|
||||
* "weak+" means 200k Ohm VDDIO
|
||||
* (-) means GND
|
||||
*/
|
||||
static void mxs_lradc_setup_touch_detection(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
|
||||
/*
|
||||
* In order to detect a touch event the 'touch detect enable' bit
|
||||
* enables:
|
||||
* - a weak pullup to the X+ connector
|
||||
* - a strong ground at the Y- connector
|
||||
*/
|
||||
writel(info[lradc->soc].mask,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
writel(info[lradc->soc].bit,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
|
||||
}
|
||||
|
||||
/*
|
||||
* YP(meas)--+-------------+
|
||||
* | |--+
|
||||
* | | |
|
||||
* YM(open)--+-------------+ |
|
||||
* +--------------+
|
||||
* | |
|
||||
* XP(+) XM(-)
|
||||
*
|
||||
* (+) means here 1.85 V
|
||||
* (-) means here GND
|
||||
*/
|
||||
static void mxs_lradc_prepare_x_pos(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
|
||||
writel(info[lradc->soc].mask,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
writel(info[lradc->soc].x_plate,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
|
||||
|
||||
ts->cur_plate = LRADC_SAMPLE_X;
|
||||
mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL1, TS_CH_YP);
|
||||
mxs_lradc_setup_ts_channel(ts, TOUCHSCREEN_VCHANNEL1);
|
||||
}
|
||||
|
||||
/*
|
||||
* YP(+)--+-------------+
|
||||
* | |--+
|
||||
* | | |
|
||||
* YM(-)--+-------------+ |
|
||||
* +--------------+
|
||||
* | |
|
||||
* XP(open) XM(meas)
|
||||
*
|
||||
* (+) means here 1.85 V
|
||||
* (-) means here GND
|
||||
*/
|
||||
static void mxs_lradc_prepare_y_pos(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
|
||||
writel(info[lradc->soc].mask,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
writel(info[lradc->soc].y_plate,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
|
||||
|
||||
ts->cur_plate = LRADC_SAMPLE_Y;
|
||||
mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL1, TS_CH_XM);
|
||||
mxs_lradc_setup_ts_channel(ts, TOUCHSCREEN_VCHANNEL1);
|
||||
}
|
||||
|
||||
/*
|
||||
* YP(+)--+-------------+
|
||||
* | |--+
|
||||
* | | |
|
||||
* YM(meas)--+-------------+ |
|
||||
* +--------------+
|
||||
* | |
|
||||
* XP(meas) XM(-)
|
||||
*
|
||||
* (+) means here 1.85 V
|
||||
* (-) means here GND
|
||||
*/
|
||||
static void mxs_lradc_prepare_pressure(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
|
||||
writel(info[lradc->soc].mask,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
writel(info[lradc->soc].pressure,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
|
||||
|
||||
ts->cur_plate = LRADC_SAMPLE_PRESSURE;
|
||||
mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL1, TS_CH_YM);
|
||||
mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL2, TS_CH_XP);
|
||||
mxs_lradc_setup_ts_pressure(ts, TOUCHSCREEN_VCHANNEL2,
|
||||
TOUCHSCREEN_VCHANNEL1);
|
||||
}
|
||||
|
||||
static void mxs_lradc_enable_touch_detection(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
mxs_lradc_setup_touch_detection(ts);
|
||||
|
||||
ts->cur_plate = LRADC_TOUCH;
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ | LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
|
||||
}
|
||||
|
||||
static void mxs_lradc_start_touch_event(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
writel(LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1),
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
|
||||
/*
|
||||
* start with the Y-pos, because it uses nearly the same plate
|
||||
* settings like the touch detection
|
||||
*/
|
||||
mxs_lradc_prepare_y_pos(ts);
|
||||
}
|
||||
|
||||
static void mxs_lradc_report_ts_event(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
input_report_abs(ts->ts_input, ABS_X, ts->ts_x_pos);
|
||||
input_report_abs(ts->ts_input, ABS_Y, ts->ts_y_pos);
|
||||
input_report_abs(ts->ts_input, ABS_PRESSURE, ts->ts_pressure);
|
||||
input_report_key(ts->ts_input, BTN_TOUCH, 1);
|
||||
input_sync(ts->ts_input);
|
||||
}
|
||||
|
||||
static void mxs_lradc_complete_touch_event(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
mxs_lradc_setup_touch_detection(ts);
|
||||
ts->cur_plate = LRADC_SAMPLE_VALID;
|
||||
/*
|
||||
* start a dummy conversion to burn time to settle the signals
|
||||
* note: we are not interested in the conversion's value
|
||||
*/
|
||||
writel(0, ts->base + LRADC_CH(TOUCHSCREEN_VCHANNEL1));
|
||||
writel(LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
|
||||
LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2),
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
writel(LRADC_DELAY_TRIGGER(1 << TOUCHSCREEN_VCHANNEL1) |
|
||||
LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10),
|
||||
ts->base + LRADC_DELAY(2));
|
||||
}
|
||||
|
||||
/*
|
||||
* in order to avoid false measurements, report only samples where
|
||||
* the surface is still touched after the position measurement
|
||||
*/
|
||||
static void mxs_lradc_finish_touch_event(struct mxs_lradc_ts *ts, bool valid)
|
||||
{
|
||||
/* if it is still touched, report the sample */
|
||||
if (valid && mxs_lradc_check_touch_event(ts)) {
|
||||
ts->ts_valid = true;
|
||||
mxs_lradc_report_ts_event(ts);
|
||||
}
|
||||
|
||||
/* if it is even still touched, continue with the next measurement */
|
||||
if (mxs_lradc_check_touch_event(ts)) {
|
||||
mxs_lradc_prepare_y_pos(ts);
|
||||
return;
|
||||
}
|
||||
|
||||
if (ts->ts_valid) {
|
||||
/* signal the release */
|
||||
ts->ts_valid = false;
|
||||
input_report_key(ts->ts_input, BTN_TOUCH, 0);
|
||||
input_sync(ts->ts_input);
|
||||
}
|
||||
|
||||
/* if it is released, wait for the next touch via IRQ */
|
||||
ts->cur_plate = LRADC_TOUCH;
|
||||
writel(0, ts->base + LRADC_DELAY(2));
|
||||
writel(0, ts->base + LRADC_DELAY(3));
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ |
|
||||
LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) |
|
||||
LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1),
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
|
||||
}
|
||||
|
||||
/* touchscreen's state machine */
|
||||
static void mxs_lradc_handle_touch(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
switch (ts->cur_plate) {
|
||||
case LRADC_TOUCH:
|
||||
if (mxs_lradc_check_touch_event(ts))
|
||||
mxs_lradc_start_touch_event(ts);
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
return;
|
||||
|
||||
case LRADC_SAMPLE_Y:
|
||||
ts->ts_y_pos =
|
||||
mxs_lradc_ts_read_raw_channel(ts, TOUCHSCREEN_VCHANNEL1);
|
||||
mxs_lradc_prepare_x_pos(ts);
|
||||
return;
|
||||
|
||||
case LRADC_SAMPLE_X:
|
||||
ts->ts_x_pos =
|
||||
mxs_lradc_ts_read_raw_channel(ts, TOUCHSCREEN_VCHANNEL1);
|
||||
mxs_lradc_prepare_pressure(ts);
|
||||
return;
|
||||
|
||||
case LRADC_SAMPLE_PRESSURE:
|
||||
ts->ts_pressure =
|
||||
mxs_lradc_read_ts_pressure(ts,
|
||||
TOUCHSCREEN_VCHANNEL2,
|
||||
TOUCHSCREEN_VCHANNEL1);
|
||||
mxs_lradc_complete_touch_event(ts);
|
||||
return;
|
||||
|
||||
case LRADC_SAMPLE_VALID:
|
||||
mxs_lradc_finish_touch_event(ts, 1);
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
/* IRQ Handling */
|
||||
static irqreturn_t mxs_lradc_ts_handle_irq(int irq, void *data)
|
||||
{
|
||||
struct mxs_lradc_ts *ts = data;
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
unsigned long reg = readl(ts->base + LRADC_CTRL1);
|
||||
u32 clr_irq = mxs_lradc_irq_mask(lradc);
|
||||
const u32 ts_irq_mask =
|
||||
LRADC_CTRL1_TOUCH_DETECT_IRQ |
|
||||
LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
|
||||
LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2);
|
||||
unsigned long flags;
|
||||
|
||||
if (!(reg & mxs_lradc_irq_mask(lradc)))
|
||||
return IRQ_NONE;
|
||||
|
||||
if (reg & ts_irq_mask) {
|
||||
spin_lock_irqsave(&ts->lock, flags);
|
||||
mxs_lradc_handle_touch(ts);
|
||||
spin_unlock_irqrestore(&ts->lock, flags);
|
||||
/* Make sure we don't clear the next conversion's interrupt. */
|
||||
clr_irq &= ~(LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
|
||||
LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2));
|
||||
writel(reg & clr_irq,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
}
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int mxs_lradc_ts_open(struct input_dev *dev)
|
||||
{
|
||||
struct mxs_lradc_ts *ts = input_get_drvdata(dev);
|
||||
|
||||
/* Enable the touch-detect circuitry. */
|
||||
mxs_lradc_enable_touch_detection(ts);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void mxs_lradc_ts_stop(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
int i;
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
|
||||
/* stop all interrupts from firing */
|
||||
writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
|
||||
LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) |
|
||||
LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL2),
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
/* Power-down touchscreen touch-detect circuitry. */
|
||||
writel(info[lradc->soc].mask,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
writel(lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
|
||||
ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
for (i = 1; i < LRADC_MAX_DELAY_CHANS; i++)
|
||||
writel(0, ts->base + LRADC_DELAY(i));
|
||||
}
|
||||
|
||||
static void mxs_lradc_ts_close(struct input_dev *dev)
|
||||
{
|
||||
struct mxs_lradc_ts *ts = input_get_drvdata(dev);
|
||||
|
||||
mxs_lradc_ts_stop(ts);
|
||||
}
|
||||
|
||||
static void mxs_lradc_ts_hw_init(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
struct mxs_lradc *lradc = ts->lradc;
|
||||
|
||||
/* Configure the touchscreen type */
|
||||
if (lradc->soc == IMX28_LRADC) {
|
||||
writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
|
||||
|
||||
if (lradc->touchscreen_wire == MXS_LRADC_TOUCHSCREEN_5WIRE)
|
||||
writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
|
||||
ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
|
||||
}
|
||||
}
|
||||
|
||||
static int mxs_lradc_ts_register(struct mxs_lradc_ts *ts)
|
||||
{
|
||||
struct input_dev *input = ts->ts_input;
|
||||
struct device *dev = ts->dev;
|
||||
|
||||
input = devm_input_allocate_device(dev);
|
||||
if (!input)
|
||||
return -ENOMEM;
|
||||
|
||||
input->name = "mxs-lradc-ts";
|
||||
input->id.bustype = BUS_HOST;
|
||||
input->open = mxs_lradc_ts_open;
|
||||
input->close = mxs_lradc_ts_close;
|
||||
|
||||
__set_bit(INPUT_PROP_DIRECT, input->propbit);
|
||||
input_set_capability(input, EV_KEY, BTN_TOUCH);
|
||||
input_set_abs_params(input, ABS_X, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
|
||||
input_set_abs_params(input, ABS_Y, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
|
||||
input_set_abs_params(input, ABS_PRESSURE, 0, LRADC_SINGLE_SAMPLE_MASK,
|
||||
0, 0);
|
||||
|
||||
ts->ts_input = input;
|
||||
input_set_drvdata(input, ts);
|
||||
|
||||
return input_register_device(input);
|
||||
}
|
||||
|
||||
static int mxs_lradc_ts_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct device *dev = &pdev->dev;
|
||||
struct device_node *node = dev->parent->of_node;
|
||||
struct mxs_lradc *lradc = dev_get_drvdata(dev->parent);
|
||||
struct mxs_lradc_ts *ts;
|
||||
struct resource *iores;
|
||||
int ret, irq, virq, i;
|
||||
u32 ts_wires = 0, adapt;
|
||||
|
||||
ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
|
||||
if (!ts)
|
||||
return -ENOMEM;
|
||||
|
||||
platform_set_drvdata(pdev, ts);
|
||||
|
||||
ts->lradc = lradc;
|
||||
ts->dev = dev;
|
||||
spin_lock_init(&ts->lock);
|
||||
|
||||
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
ts->base = devm_ioremap(dev, iores->start, resource_size(iores));
|
||||
if (IS_ERR(ts->base))
|
||||
return PTR_ERR(ts->base);
|
||||
|
||||
ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
|
||||
&ts_wires);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
if (of_property_read_u32(node, "fsl,ave-ctrl", &adapt)) {
|
||||
ts->over_sample_cnt = 4;
|
||||
} else {
|
||||
if (adapt >= 1 || adapt <= 32) {
|
||||
ts->over_sample_cnt = adapt;
|
||||
} else {
|
||||
dev_err(ts->dev, "Invalid sample count (%u)\n",
|
||||
adapt);
|
||||
return -EINVAL;
|
||||
}
|
||||
}
|
||||
|
||||
if (of_property_read_u32(node, "fsl,ave-delay", &adapt)) {
|
||||
ts->over_sample_delay = 2;
|
||||
} else {
|
||||
if (adapt >= 2 || adapt <= LRADC_DELAY_DELAY_MASK + 1) {
|
||||
ts->over_sample_delay = adapt;
|
||||
} else {
|
||||
dev_err(ts->dev, "Invalid sample delay (%u)\n",
|
||||
adapt);
|
||||
return -EINVAL;
|
||||
}
|
||||
}
|
||||
|
||||
if (of_property_read_u32(node, "fsl,settling", &adapt)) {
|
||||
ts->settling_delay = 10;
|
||||
} else {
|
||||
if (adapt >= 1 || adapt <= LRADC_DELAY_DELAY_MASK) {
|
||||
ts->settling_delay = adapt;
|
||||
} else {
|
||||
dev_err(ts->dev, "Invalid settling delay (%u)\n",
|
||||
adapt);
|
||||
return -EINVAL;
|
||||
}
|
||||
}
|
||||
|
||||
ret = stmp_reset_block(ts->base);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
mxs_lradc_ts_hw_init(ts);
|
||||
|
||||
for (i = 0; i < 3; i++) {
|
||||
irq = platform_get_irq_byname(pdev, mxs_lradc_ts_irq_names[i]);
|
||||
if (irq < 0)
|
||||
return irq;
|
||||
|
||||
virq = irq_of_parse_and_map(node, irq);
|
||||
|
||||
mxs_lradc_ts_stop(ts);
|
||||
|
||||
ret = devm_request_irq(dev, virq,
|
||||
mxs_lradc_ts_handle_irq,
|
||||
0, mxs_lradc_ts_irq_names[i], ts);
|
||||
if (ret)
|
||||
return ret;
|
||||
}
|
||||
|
||||
return mxs_lradc_ts_register(ts);
|
||||
}
|
||||
|
||||
static struct platform_driver mxs_lradc_ts_driver = {
|
||||
.driver = {
|
||||
.name = "mxs-lradc-ts",
|
||||
},
|
||||
.probe = mxs_lradc_ts_probe,
|
||||
};
|
||||
module_platform_driver(mxs_lradc_ts_driver);
|
||||
|
||||
MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
|
||||
MODULE_DESCRIPTION("Freescale MXS LRADC touchscreen driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_ALIAS("platform:mxs-lradc-ts");
|
||||
|
|
@ -344,6 +344,23 @@ config MFD_MC13XXX_I2C
|
|||
help
|
||||
Select this if your MC13xxx is connected via an I2C bus.
|
||||
|
||||
config MFD_MXS_LRADC
|
||||
tristate "Freescale i.MX23/i.MX28 LRADC"
|
||||
depends on ARCH_MXS || COMPILE_TEST
|
||||
select MFD_CORE
|
||||
select STMP_DEVICE
|
||||
help
|
||||
Say yes here to build support for the Low Resolution
|
||||
Analog-to-Digital Converter (LRADC) found on the i.MX23 and i.MX28
|
||||
processors. This driver provides common support for accessing the
|
||||
device, additional drivers must be enabled in order to use the
|
||||
functionality of the device:
|
||||
mxs-lradc-adc for ADC readings
|
||||
mxs-lradc-ts for touchscreen support
|
||||
|
||||
This driver can also be built as a module. If so, the module will be
|
||||
called mxs-lradc.
|
||||
|
||||
config MFD_MX25_TSADC
|
||||
tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
|
||||
select REGMAP_MMIO
|
||||
|
|
|
|||
|
|
@ -215,3 +215,4 @@ obj-$(CONFIG_MFD_ALTERA_A10SR) += altera-a10sr.o
|
|||
obj-$(CONFIG_MFD_SUN4I_GPADC) += sun4i-gpadc.o
|
||||
|
||||
obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
|
||||
obj-$(CONFIG_MFD_MXS_LRADC) += mxs-lradc.o
|
||||
|
|
|
|||
|
|
@ -18,11 +18,11 @@
|
|||
#include <linux/io.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/mfd/syscon.h>
|
||||
#include <linux/mfd/syscon/exynos5-pmu.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_platform.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/soc/samsung/exynos-regs-pmu.h>
|
||||
#include <linux/types.h>
|
||||
|
||||
/* LPASS Top register definitions */
|
||||
|
|
@ -83,7 +83,7 @@ static void exynos_lpass_enable(struct exynos_lpass *lpass)
|
|||
|
||||
/* Activate related PADs from retention state */
|
||||
regmap_write(lpass->pmu, EXYNOS5433_PAD_RETENTION_AUD_OPTION,
|
||||
EXYNOS5433_PAD_INITIATE_WAKEUP_FROM_LOWPWR);
|
||||
EXYNOS_WAKEUP_FROM_LOWPWR);
|
||||
|
||||
exynos_lpass_core_sw_reset(lpass, LPASS_I2S_SW_RESET);
|
||||
exynos_lpass_core_sw_reset(lpass, LPASS_DMA_SW_RESET);
|
||||
|
|
|
|||
|
|
@ -23,6 +23,8 @@
|
|||
|
||||
#define CPCAP_NR_IRQ_REG_BANKS 6
|
||||
#define CPCAP_NR_IRQ_CHIPS 3
|
||||
#define CPCAP_REGISTER_SIZE 4
|
||||
#define CPCAP_REGISTER_BITS 16
|
||||
|
||||
struct cpcap_ddata {
|
||||
struct spi_device *spi;
|
||||
|
|
@ -32,6 +34,32 @@ struct cpcap_ddata {
|
|||
struct regmap *regmap;
|
||||
};
|
||||
|
||||
static int cpcap_sense_irq(struct regmap *regmap, int irq)
|
||||
{
|
||||
int regnum = irq / CPCAP_REGISTER_BITS;
|
||||
int mask = BIT(irq % CPCAP_REGISTER_BITS);
|
||||
int reg = CPCAP_REG_INTS1 + (regnum * CPCAP_REGISTER_SIZE);
|
||||
int err, val;
|
||||
|
||||
if (reg < CPCAP_REG_INTS1 || reg > CPCAP_REG_INTS4)
|
||||
return -EINVAL;
|
||||
|
||||
err = regmap_read(regmap, reg, &val);
|
||||
if (err)
|
||||
return err;
|
||||
|
||||
return !!(val & mask);
|
||||
}
|
||||
|
||||
int cpcap_sense_virq(struct regmap *regmap, int virq)
|
||||
{
|
||||
struct regmap_irq_chip_data *d = irq_get_chip_data(virq);
|
||||
int irq_base = regmap_irq_chip_get_base(d);
|
||||
|
||||
return cpcap_sense_irq(regmap, virq - irq_base);
|
||||
}
|
||||
EXPORT_SYMBOL_GPL(cpcap_sense_virq);
|
||||
|
||||
static int cpcap_check_revision(struct cpcap_ddata *cpcap)
|
||||
{
|
||||
u16 vendor, rev;
|
||||
|
|
|
|||
|
|
@ -0,0 +1,267 @@
|
|||
/*
|
||||
* Freescale MXS Low Resolution Analog-to-Digital Converter driver
|
||||
*
|
||||
* Copyright (c) 2012 DENX Software Engineering, GmbH.
|
||||
* Copyright (c) 2017 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* Authors:
|
||||
* Marek Vasut <marex@denx.de>
|
||||
* Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include <linux/clk.h>
|
||||
#include <linux/device.h>
|
||||
#include <linux/mfd/core.h>
|
||||
#include <linux/mfd/mxs-lradc.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_device.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
#define ADC_CELL 0
|
||||
#define TSC_CELL 1
|
||||
#define RES_MEM 0
|
||||
|
||||
enum mx23_lradc_irqs {
|
||||
MX23_LRADC_TS_IRQ = 0,
|
||||
MX23_LRADC_CH0_IRQ,
|
||||
MX23_LRADC_CH1_IRQ,
|
||||
MX23_LRADC_CH2_IRQ,
|
||||
MX23_LRADC_CH3_IRQ,
|
||||
MX23_LRADC_CH4_IRQ,
|
||||
MX23_LRADC_CH5_IRQ,
|
||||
MX23_LRADC_CH6_IRQ,
|
||||
MX23_LRADC_CH7_IRQ,
|
||||
};
|
||||
|
||||
enum mx28_lradc_irqs {
|
||||
MX28_LRADC_TS_IRQ = 0,
|
||||
MX28_LRADC_TRESH0_IRQ,
|
||||
MX28_LRADC_TRESH1_IRQ,
|
||||
MX28_LRADC_CH0_IRQ,
|
||||
MX28_LRADC_CH1_IRQ,
|
||||
MX28_LRADC_CH2_IRQ,
|
||||
MX28_LRADC_CH3_IRQ,
|
||||
MX28_LRADC_CH4_IRQ,
|
||||
MX28_LRADC_CH5_IRQ,
|
||||
MX28_LRADC_CH6_IRQ,
|
||||
MX28_LRADC_CH7_IRQ,
|
||||
MX28_LRADC_BUTTON0_IRQ,
|
||||
MX28_LRADC_BUTTON1_IRQ,
|
||||
};
|
||||
|
||||
static struct resource mx23_adc_resources[] = {
|
||||
DEFINE_RES_MEM(0x0, 0x0),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH0_IRQ, "mxs-lradc-channel0"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH1_IRQ, "mxs-lradc-channel1"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH2_IRQ, "mxs-lradc-channel2"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH3_IRQ, "mxs-lradc-channel3"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH4_IRQ, "mxs-lradc-channel4"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH5_IRQ, "mxs-lradc-channel5"),
|
||||
};
|
||||
|
||||
static struct resource mx23_touchscreen_resources[] = {
|
||||
DEFINE_RES_MEM(0x0, 0x0),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_TS_IRQ, "mxs-lradc-touchscreen"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH6_IRQ, "mxs-lradc-channel6"),
|
||||
DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH7_IRQ, "mxs-lradc-channel7"),
|
||||
};
|
||||
|
||||
static struct resource mx28_adc_resources[] = {
|
||||
DEFINE_RES_MEM(0x0, 0x0),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_TRESH0_IRQ, "mxs-lradc-thresh0"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_TRESH1_IRQ, "mxs-lradc-thresh1"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH0_IRQ, "mxs-lradc-channel0"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH1_IRQ, "mxs-lradc-channel1"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH2_IRQ, "mxs-lradc-channel2"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH3_IRQ, "mxs-lradc-channel3"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH4_IRQ, "mxs-lradc-channel4"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH5_IRQ, "mxs-lradc-channel5"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_BUTTON0_IRQ, "mxs-lradc-button0"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_BUTTON1_IRQ, "mxs-lradc-button1"),
|
||||
};
|
||||
|
||||
static struct resource mx28_touchscreen_resources[] = {
|
||||
DEFINE_RES_MEM(0x0, 0x0),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_TS_IRQ, "mxs-lradc-touchscreen"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH6_IRQ, "mxs-lradc-channel6"),
|
||||
DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH7_IRQ, "mxs-lradc-channel7"),
|
||||
};
|
||||
|
||||
static struct mfd_cell mx23_cells[] = {
|
||||
{
|
||||
.name = "mxs-lradc-adc",
|
||||
.resources = mx23_adc_resources,
|
||||
.num_resources = ARRAY_SIZE(mx23_adc_resources),
|
||||
},
|
||||
{
|
||||
.name = "mxs-lradc-ts",
|
||||
.resources = mx23_touchscreen_resources,
|
||||
.num_resources = ARRAY_SIZE(mx23_touchscreen_resources),
|
||||
},
|
||||
};
|
||||
|
||||
static struct mfd_cell mx28_cells[] = {
|
||||
{
|
||||
.name = "mxs-lradc-adc",
|
||||
.resources = mx28_adc_resources,
|
||||
.num_resources = ARRAY_SIZE(mx28_adc_resources),
|
||||
},
|
||||
{
|
||||
.name = "mxs-lradc-ts",
|
||||
.resources = mx28_touchscreen_resources,
|
||||
.num_resources = ARRAY_SIZE(mx28_touchscreen_resources),
|
||||
}
|
||||
};
|
||||
|
||||
static const struct of_device_id mxs_lradc_dt_ids[] = {
|
||||
{ .compatible = "fsl,imx23-lradc", .data = (void *)IMX23_LRADC, },
|
||||
{ .compatible = "fsl,imx28-lradc", .data = (void *)IMX28_LRADC, },
|
||||
{ /* sentinel */ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
|
||||
|
||||
static int mxs_lradc_probe(struct platform_device *pdev)
|
||||
{
|
||||
const struct of_device_id *of_id;
|
||||
struct device *dev = &pdev->dev;
|
||||
struct device_node *node = dev->of_node;
|
||||
struct mxs_lradc *lradc;
|
||||
struct mfd_cell *cells = NULL;
|
||||
struct resource *res;
|
||||
int ret = 0;
|
||||
u32 ts_wires = 0;
|
||||
|
||||
lradc = devm_kzalloc(&pdev->dev, sizeof(*lradc), GFP_KERNEL);
|
||||
if (!lradc)
|
||||
return -ENOMEM;
|
||||
|
||||
of_id = of_match_device(mxs_lradc_dt_ids, &pdev->dev);
|
||||
if (!of_id)
|
||||
return -EINVAL;
|
||||
|
||||
lradc->soc = (enum mxs_lradc_id)of_id->data;
|
||||
|
||||
lradc->clk = devm_clk_get(&pdev->dev, NULL);
|
||||
if (IS_ERR(lradc->clk)) {
|
||||
dev_err(dev, "Failed to get the delay unit clock\n");
|
||||
return PTR_ERR(lradc->clk);
|
||||
}
|
||||
|
||||
ret = clk_prepare_enable(lradc->clk);
|
||||
if (ret) {
|
||||
dev_err(dev, "Failed to enable the delay unit clock\n");
|
||||
return ret;
|
||||
}
|
||||
|
||||
ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
|
||||
&ts_wires);
|
||||
|
||||
if (!ret) {
|
||||
lradc->buffer_vchans = BUFFER_VCHANS_LIMITED;
|
||||
|
||||
switch (ts_wires) {
|
||||
case 4:
|
||||
lradc->touchscreen_wire = MXS_LRADC_TOUCHSCREEN_4WIRE;
|
||||
break;
|
||||
case 5:
|
||||
if (lradc->soc == IMX28_LRADC) {
|
||||
lradc->touchscreen_wire =
|
||||
MXS_LRADC_TOUCHSCREEN_5WIRE;
|
||||
break;
|
||||
}
|
||||
/* fall through to an error message for i.MX23 */
|
||||
default:
|
||||
dev_err(&pdev->dev,
|
||||
"Unsupported number of touchscreen wires (%d)\n"
|
||||
, ts_wires);
|
||||
ret = -EINVAL;
|
||||
goto err_clk;
|
||||
}
|
||||
} else {
|
||||
lradc->buffer_vchans = BUFFER_VCHANS_ALL;
|
||||
}
|
||||
|
||||
platform_set_drvdata(pdev, lradc);
|
||||
|
||||
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
if (!res)
|
||||
return -ENOMEM;
|
||||
|
||||
switch (lradc->soc) {
|
||||
case IMX23_LRADC:
|
||||
mx23_adc_resources[RES_MEM] = *res;
|
||||
mx23_touchscreen_resources[RES_MEM] = *res;
|
||||
cells = mx23_cells;
|
||||
break;
|
||||
case IMX28_LRADC:
|
||||
mx28_adc_resources[RES_MEM] = *res;
|
||||
mx28_touchscreen_resources[RES_MEM] = *res;
|
||||
cells = mx28_cells;
|
||||
break;
|
||||
default:
|
||||
dev_err(dev, "Unsupported SoC\n");
|
||||
ret = -ENODEV;
|
||||
goto err_clk;
|
||||
}
|
||||
|
||||
ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
|
||||
&cells[ADC_CELL], 1, NULL, 0, NULL);
|
||||
if (ret) {
|
||||
dev_err(&pdev->dev, "Failed to add the ADC subdevice\n");
|
||||
goto err_clk;
|
||||
}
|
||||
|
||||
if (!lradc->touchscreen_wire)
|
||||
return 0;
|
||||
|
||||
ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
|
||||
&cells[TSC_CELL], 1, NULL, 0, NULL);
|
||||
if (ret) {
|
||||
dev_err(&pdev->dev,
|
||||
"Failed to add the touchscreen subdevice\n");
|
||||
goto err_clk;
|
||||
}
|
||||
|
||||
return 0;
|
||||
|
||||
err_clk:
|
||||
clk_disable_unprepare(lradc->clk);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int mxs_lradc_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct mxs_lradc *lradc = platform_get_drvdata(pdev);
|
||||
|
||||
clk_disable_unprepare(lradc->clk);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct platform_driver mxs_lradc_driver = {
|
||||
.driver = {
|
||||
.name = "mxs-lradc",
|
||||
.of_match_table = mxs_lradc_dt_ids,
|
||||
},
|
||||
.probe = mxs_lradc_probe,
|
||||
.remove = mxs_lradc_remove,
|
||||
};
|
||||
module_platform_driver(mxs_lradc_driver);
|
||||
|
||||
MODULE_AUTHOR("Ksenija Stanojevic <ksenija.stanojevic@gmail.com>");
|
||||
MODULE_DESCRIPTION("Freescale i.MX23/i.MX28 LRADC driver");
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_ALIAS("platform:mxs-lradc");
|
||||
|
|
@ -777,6 +777,7 @@ exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
|
|||
{
|
||||
struct samsung_retention_ctrl *ctrl;
|
||||
struct regmap *pmu_regs;
|
||||
int i;
|
||||
|
||||
ctrl = devm_kzalloc(drvdata->dev, sizeof(*ctrl), GFP_KERNEL);
|
||||
if (!ctrl)
|
||||
|
|
@ -794,6 +795,10 @@ exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
|
|||
ctrl->enable = exynos_retention_enable;
|
||||
ctrl->disable = exynos_retention_disable;
|
||||
|
||||
/* Ensure that retention is disabled on driver init */
|
||||
for (i = 0; i < ctrl->nr_regs; i++)
|
||||
regmap_write(pmu_regs, ctrl->regs[i], ctrl->value);
|
||||
|
||||
return ctrl;
|
||||
}
|
||||
|
||||
|
|
@ -1546,6 +1551,54 @@ static const struct samsung_pin_bank_data exynos5433_pin_banks9[] __initconst =
|
|||
EXYNOS_PIN_BANK_EINTG(3, 0x000, "gpj1", 0x00),
|
||||
};
|
||||
|
||||
/* PMU pin retention groups registers for Exynos5433 (without audio & fsys) */
|
||||
static const u32 exynos5433_retention_regs[] = {
|
||||
EXYNOS5433_PAD_RETENTION_TOP_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_UART_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_EBIA_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_EBIB_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_SPI_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_MIF_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_USBXTI_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_BOOTLDO_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_UFS_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_FSYSGENIO_OPTION,
|
||||
};
|
||||
|
||||
static const struct samsung_retention_data exynos5433_retention_data __initconst = {
|
||||
.regs = exynos5433_retention_regs,
|
||||
.nr_regs = ARRAY_SIZE(exynos5433_retention_regs),
|
||||
.value = EXYNOS_WAKEUP_FROM_LOWPWR,
|
||||
.refcnt = &exynos_shared_retention_refcnt,
|
||||
.init = exynos_retention_init,
|
||||
};
|
||||
|
||||
/* PMU retention control for audio pins can be tied to audio pin bank */
|
||||
static const u32 exynos5433_audio_retention_regs[] = {
|
||||
EXYNOS5433_PAD_RETENTION_AUD_OPTION,
|
||||
};
|
||||
|
||||
static const struct samsung_retention_data exynos5433_audio_retention_data __initconst = {
|
||||
.regs = exynos5433_audio_retention_regs,
|
||||
.nr_regs = ARRAY_SIZE(exynos5433_audio_retention_regs),
|
||||
.value = EXYNOS_WAKEUP_FROM_LOWPWR,
|
||||
.init = exynos_retention_init,
|
||||
};
|
||||
|
||||
/* PMU retention control for mmc pins can be tied to fsys pin bank */
|
||||
static const u32 exynos5433_fsys_retention_regs[] = {
|
||||
EXYNOS5433_PAD_RETENTION_MMC0_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_MMC1_OPTION,
|
||||
EXYNOS5433_PAD_RETENTION_MMC2_OPTION,
|
||||
};
|
||||
|
||||
static const struct samsung_retention_data exynos5433_fsys_retention_data __initconst = {
|
||||
.regs = exynos5433_fsys_retention_regs,
|
||||
.nr_regs = ARRAY_SIZE(exynos5433_fsys_retention_regs),
|
||||
.value = EXYNOS_WAKEUP_FROM_LOWPWR,
|
||||
.init = exynos_retention_init,
|
||||
};
|
||||
|
||||
/*
|
||||
* Samsung pinctrl driver data for Exynos5433 SoC. Exynos5433 SoC includes
|
||||
* ten gpio/pin-mux/pinconfig controllers.
|
||||
|
|
@ -1559,6 +1612,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.nr_ext_resources = 1,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 1 data */
|
||||
.pin_banks = exynos5433_pin_banks1,
|
||||
|
|
@ -1566,6 +1620,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_audio_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 2 data */
|
||||
.pin_banks = exynos5433_pin_banks2,
|
||||
|
|
@ -1573,6 +1628,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 3 data */
|
||||
.pin_banks = exynos5433_pin_banks3,
|
||||
|
|
@ -1580,6 +1636,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 4 data */
|
||||
.pin_banks = exynos5433_pin_banks4,
|
||||
|
|
@ -1587,6 +1644,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 5 data */
|
||||
.pin_banks = exynos5433_pin_banks5,
|
||||
|
|
@ -1594,6 +1652,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_fsys_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 6 data */
|
||||
.pin_banks = exynos5433_pin_banks6,
|
||||
|
|
@ -1601,6 +1660,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 7 data */
|
||||
.pin_banks = exynos5433_pin_banks7,
|
||||
|
|
@ -1608,6 +1668,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 8 data */
|
||||
.pin_banks = exynos5433_pin_banks8,
|
||||
|
|
@ -1615,6 +1676,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
}, {
|
||||
/* pin-controller instance 9 data */
|
||||
.pin_banks = exynos5433_pin_banks9,
|
||||
|
|
@ -1622,6 +1684,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
|
|||
.eint_gpio_init = exynos_eint_gpio_init,
|
||||
.suspend = exynos_pinctrl_suspend,
|
||||
.resume = exynos_pinctrl_resume,
|
||||
.retention_data = &exynos5433_retention_data,
|
||||
},
|
||||
};
|
||||
|
||||
|
|
|
|||
|
|
@ -14,6 +14,9 @@
|
|||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/device.h>
|
||||
#include <linux/regmap.h>
|
||||
|
||||
#define CPCAP_VENDOR_ST 0
|
||||
#define CPCAP_VENDOR_TI 1
|
||||
|
||||
|
|
@ -290,3 +293,5 @@ static inline int cpcap_get_vendor(struct device *dev,
|
|||
|
||||
return 0;
|
||||
}
|
||||
|
||||
extern int cpcap_sense_virq(struct regmap *regmap, int virq);
|
||||
|
|
|
|||
|
|
@ -0,0 +1,187 @@
|
|||
/*
|
||||
* Freescale MXS Low Resolution Analog-to-Digital Converter driver
|
||||
*
|
||||
* Copyright (c) 2012 DENX Software Engineering, GmbH.
|
||||
* Copyright (c) 2016 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
|
||||
*
|
||||
* Author: Marek Vasut <marex@denx.de>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation; either version 2 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#ifndef __MFD_MXS_LRADC_H
|
||||
#define __MFD_MXS_LRADC_H
|
||||
|
||||
#include <linux/bitops.h>
|
||||
#include <linux/io.h>
|
||||
#include <linux/stmp_device.h>
|
||||
|
||||
#define LRADC_MAX_DELAY_CHANS 4
|
||||
#define LRADC_MAX_MAPPED_CHANS 8
|
||||
#define LRADC_MAX_TOTAL_CHANS 16
|
||||
|
||||
#define LRADC_DELAY_TIMER_HZ 2000
|
||||
|
||||
#define LRADC_CTRL0 0x00
|
||||
# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE BIT(23)
|
||||
# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE BIT(22)
|
||||
# define LRADC_CTRL0_MX28_YNNSW /* YM */ BIT(21)
|
||||
# define LRADC_CTRL0_MX28_YPNSW /* YP */ BIT(20)
|
||||
# define LRADC_CTRL0_MX28_YPPSW /* YP */ BIT(19)
|
||||
# define LRADC_CTRL0_MX28_XNNSW /* XM */ BIT(18)
|
||||
# define LRADC_CTRL0_MX28_XNPSW /* XM */ BIT(17)
|
||||
# define LRADC_CTRL0_MX28_XPPSW /* XP */ BIT(16)
|
||||
|
||||
# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE BIT(20)
|
||||
# define LRADC_CTRL0_MX23_YM BIT(19)
|
||||
# define LRADC_CTRL0_MX23_XM BIT(18)
|
||||
# define LRADC_CTRL0_MX23_YP BIT(17)
|
||||
# define LRADC_CTRL0_MX23_XP BIT(16)
|
||||
|
||||
# define LRADC_CTRL0_MX28_PLATE_MASK \
|
||||
(LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
|
||||
LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
|
||||
LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
|
||||
LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
|
||||
|
||||
# define LRADC_CTRL0_MX23_PLATE_MASK \
|
||||
(LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
|
||||
LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
|
||||
LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
|
||||
|
||||
#define LRADC_CTRL1 0x10
|
||||
#define LRADC_CTRL1_TOUCH_DETECT_IRQ_EN BIT(24)
|
||||
#define LRADC_CTRL1_LRADC_IRQ_EN(n) (1 << ((n) + 16))
|
||||
#define LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK (0x1fff << 16)
|
||||
#define LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK (0x01ff << 16)
|
||||
#define LRADC_CTRL1_LRADC_IRQ_EN_OFFSET 16
|
||||
#define LRADC_CTRL1_TOUCH_DETECT_IRQ BIT(8)
|
||||
#define LRADC_CTRL1_LRADC_IRQ(n) BIT(n)
|
||||
#define LRADC_CTRL1_MX28_LRADC_IRQ_MASK 0x1fff
|
||||
#define LRADC_CTRL1_MX23_LRADC_IRQ_MASK 0x01ff
|
||||
#define LRADC_CTRL1_LRADC_IRQ_OFFSET 0
|
||||
|
||||
#define LRADC_CTRL2 0x20
|
||||
#define LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET 24
|
||||
#define LRADC_CTRL2_TEMPSENSE_PWD BIT(15)
|
||||
|
||||
#define LRADC_STATUS 0x40
|
||||
#define LRADC_STATUS_TOUCH_DETECT_RAW BIT(0)
|
||||
|
||||
#define LRADC_CH(n) (0x50 + (0x10 * (n)))
|
||||
#define LRADC_CH_ACCUMULATE BIT(29)
|
||||
#define LRADC_CH_NUM_SAMPLES_MASK (0x1f << 24)
|
||||
#define LRADC_CH_NUM_SAMPLES_OFFSET 24
|
||||
#define LRADC_CH_NUM_SAMPLES(x) \
|
||||
((x) << LRADC_CH_NUM_SAMPLES_OFFSET)
|
||||
#define LRADC_CH_VALUE_MASK 0x3ffff
|
||||
#define LRADC_CH_VALUE_OFFSET 0
|
||||
|
||||
#define LRADC_DELAY(n) (0xd0 + (0x10 * (n)))
|
||||
#define LRADC_DELAY_TRIGGER_LRADCS_MASK (0xffUL << 24)
|
||||
#define LRADC_DELAY_TRIGGER_LRADCS_OFFSET 24
|
||||
#define LRADC_DELAY_TRIGGER(x) \
|
||||
(((x) << LRADC_DELAY_TRIGGER_LRADCS_OFFSET) & \
|
||||
LRADC_DELAY_TRIGGER_LRADCS_MASK)
|
||||
#define LRADC_DELAY_KICK BIT(20)
|
||||
#define LRADC_DELAY_TRIGGER_DELAYS_MASK (0xf << 16)
|
||||
#define LRADC_DELAY_TRIGGER_DELAYS_OFFSET 16
|
||||
#define LRADC_DELAY_TRIGGER_DELAYS(x) \
|
||||
(((x) << LRADC_DELAY_TRIGGER_DELAYS_OFFSET) & \
|
||||
LRADC_DELAY_TRIGGER_DELAYS_MASK)
|
||||
#define LRADC_DELAY_LOOP_COUNT_MASK (0x1f << 11)
|
||||
#define LRADC_DELAY_LOOP_COUNT_OFFSET 11
|
||||
#define LRADC_DELAY_LOOP(x) \
|
||||
(((x) << LRADC_DELAY_LOOP_COUNT_OFFSET) & \
|
||||
LRADC_DELAY_LOOP_COUNT_MASK)
|
||||
#define LRADC_DELAY_DELAY_MASK 0x7ff
|
||||
#define LRADC_DELAY_DELAY_OFFSET 0
|
||||
#define LRADC_DELAY_DELAY(x) \
|
||||
(((x) << LRADC_DELAY_DELAY_OFFSET) & \
|
||||
LRADC_DELAY_DELAY_MASK)
|
||||
|
||||
#define LRADC_CTRL4 0x140
|
||||
#define LRADC_CTRL4_LRADCSELECT_MASK(n) (0xf << ((n) * 4))
|
||||
#define LRADC_CTRL4_LRADCSELECT_OFFSET(n) ((n) * 4)
|
||||
#define LRADC_CTRL4_LRADCSELECT(n, x) \
|
||||
(((x) << LRADC_CTRL4_LRADCSELECT_OFFSET(n)) & \
|
||||
LRADC_CTRL4_LRADCSELECT_MASK(n))
|
||||
|
||||
#define LRADC_RESOLUTION 12
|
||||
#define LRADC_SINGLE_SAMPLE_MASK ((1 << LRADC_RESOLUTION) - 1)
|
||||
|
||||
#define BUFFER_VCHANS_LIMITED 0x3f
|
||||
#define BUFFER_VCHANS_ALL 0xff
|
||||
|
||||
/*
|
||||
* Certain LRADC channels are shared between touchscreen
|
||||
* and/or touch-buttons and generic LRADC block. Therefore when using
|
||||
* either of these, these channels are not available for the regular
|
||||
* sampling. The shared channels are as follows:
|
||||
*
|
||||
* CH0 -- Touch button #0
|
||||
* CH1 -- Touch button #1
|
||||
* CH2 -- Touch screen XPUL
|
||||
* CH3 -- Touch screen YPLL
|
||||
* CH4 -- Touch screen XNUL
|
||||
* CH5 -- Touch screen YNLR
|
||||
* CH6 -- Touch screen WIPER (5-wire only)
|
||||
*
|
||||
* The bit fields below represents which parts of the LRADC block are
|
||||
* switched into special mode of operation. These channels can not
|
||||
* be sampled as regular LRADC channels. The driver will refuse any
|
||||
* attempt to sample these channels.
|
||||
*/
|
||||
#define CHAN_MASK_TOUCHBUTTON (BIT(1) | BIT(0))
|
||||
#define CHAN_MASK_TOUCHSCREEN_4WIRE (0xf << 2)
|
||||
#define CHAN_MASK_TOUCHSCREEN_5WIRE (0x1f << 2)
|
||||
|
||||
enum mxs_lradc_id {
|
||||
IMX23_LRADC,
|
||||
IMX28_LRADC,
|
||||
};
|
||||
|
||||
enum mxs_lradc_ts_wires {
|
||||
MXS_LRADC_TOUCHSCREEN_NONE = 0,
|
||||
MXS_LRADC_TOUCHSCREEN_4WIRE,
|
||||
MXS_LRADC_TOUCHSCREEN_5WIRE,
|
||||
};
|
||||
|
||||
/**
|
||||
* struct mxs_lradc
|
||||
* @soc: soc type (IMX23 or IMX28)
|
||||
* @clk: 2 kHz clock for delay units
|
||||
* @buffer_vchans: channels that can be used during buffered capture
|
||||
* @touchscreen_wire: touchscreen type (4-wire or 5-wire)
|
||||
* @use_touchbutton: button state (on or off)
|
||||
*/
|
||||
struct mxs_lradc {
|
||||
enum mxs_lradc_id soc;
|
||||
struct clk *clk;
|
||||
u8 buffer_vchans;
|
||||
|
||||
enum mxs_lradc_ts_wires touchscreen_wire;
|
||||
bool use_touchbutton;
|
||||
};
|
||||
|
||||
static inline u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
|
||||
{
|
||||
switch (lradc->soc) {
|
||||
case IMX23_LRADC:
|
||||
return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
|
||||
case IMX28_LRADC:
|
||||
return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
|
||||
default:
|
||||
return 0;
|
||||
}
|
||||
}
|
||||
|
||||
#endif /* __MXS_LRADC_H */
|
||||
Loading…
Reference in New Issue