arm64: dts: marvell: Add device tree for uDPU board
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point unit made by Methode Electronics which offers complete modularity with replaceable SFP modules both for uplink and downlink (G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable). On-board features: - 512 MiB DDR3 - 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC - USB 2.0 Type-C connector - 4GB eMMC - ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type) Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Luis Torres <luis.torres@methode.com> Cc: Scott Roberts <scott.roberts@telus.com> Cc: Paul Arola <paul.arola@telus.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This commit is contained in:
parent
c54932d42a
commit
0d45062cfc
|
@ -2,6 +2,7 @@
|
|||
# Mvebu SoC Family
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
|
||||
dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
|
||||
|
|
|
@ -0,0 +1,162 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Device tree for the uDPU board.
|
||||
* Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
|
||||
* Copyright (C) 2016 Marvell
|
||||
* Copyright (C) 2019 Methode Electronics
|
||||
* Copyright (C) 2019 Telus
|
||||
*
|
||||
* Vladimir Vid <vladimir.vid@sartura.hr>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include "armada-372x.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Methode uDPU Board";
|
||||
compatible = "methode,udpu", "marvell,armada3720";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
pinctrl-names = "default";
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power1 {
|
||||
label = "udpu:green:power";
|
||||
gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power2 {
|
||||
label = "udpu:red:power";
|
||||
gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
network1 {
|
||||
label = "udpu:green:network";
|
||||
gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
network2 {
|
||||
label = "udpu:red:network";
|
||||
gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
alarm1 {
|
||||
label = "udpu:green:alarm";
|
||||
gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
alarm2 {
|
||||
label = "udpu:red:alarm";
|
||||
gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
sfp_eth0: sfp-eth0 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c0>;
|
||||
los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
|
||||
tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sfp_eth1: sfp-eth1 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&i2c1>;
|
||||
los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
|
||||
tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&sdhci0 {
|
||||
status = "okay";
|
||||
bus-width = <8>;
|
||||
mmc-ddr-1_8v;
|
||||
mmc-hs400-1_8v;
|
||||
marvell,pad-type = "fixed-1-8v";
|
||||
non-removable;
|
||||
no-sd;
|
||||
no-sdio;
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi_quad_pins>;
|
||||
|
||||
m25p80@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <54000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
/* only bootloader is located on the SPI */
|
||||
partition@0 {
|
||||
label = "uboot";
|
||||
reg = <0 0x400000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c1_pins>;
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_pins>;
|
||||
|
||||
lm75@48 {
|
||||
status = "okay";
|
||||
compatible = "lm75";
|
||||
reg = <0x48>;
|
||||
};
|
||||
|
||||
lm75@49 {
|
||||
status = "okay";
|
||||
compatible = "lm75";
|
||||
reg = <0x49>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
phy-mode = "sgmii";
|
||||
status = "okay";
|
||||
managed = "in-band-status";
|
||||
sfp = <&sfp_eth0>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
phy-mode = "sgmii";
|
||||
status = "okay";
|
||||
managed = "in-band-status";
|
||||
sfp = <&sfp_eth1>;
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
Loading…
Reference in New Issue