From 07e846bace717729fd20b5d99521a5f8c7d7a9cb Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Sun, 5 Aug 2018 20:34:05 -0700 Subject: [PATCH] x86/doc: Fix Documentation/x86/earlyprintk.txt Fix a few issues in Documentation/x86/earlyprintk.txt: - correct typos, punctuation, missing word, wrong word - change product name from Netchip to NetChip - expand where to add "earlyprintk=dbg" Signed-off-by: Randy Dunlap Cc: Eric W. Biederman Cc: Jason Wessel Cc: Linus Torvalds Cc: Peter Zijlstra Cc: Thomas Gleixner Cc: Yinghai Lu Cc: linux-doc@vger.kernel.org Cc: linux-usb@vger.kernel.org Link: http://lkml.kernel.org/r/d0c40ac3-7659-6374-dbda-23d3d2577f30@infradead.org Signed-off-by: Ingo Molnar --- Documentation/x86/earlyprintk.txt | 25 +++++++++++++++---------- 1 file changed, 15 insertions(+), 10 deletions(-) diff --git a/Documentation/x86/earlyprintk.txt b/Documentation/x86/earlyprintk.txt index 688e3eeed21d..46933e06c972 100644 --- a/Documentation/x86/earlyprintk.txt +++ b/Documentation/x86/earlyprintk.txt @@ -35,25 +35,25 @@ and two USB cables, connected like this: ( If your system does not list a debug port capability then you probably won't be able to use the USB debug key. ) - b.) You also need a Netchip USB debug cable/key: + b.) You also need a NetChip USB debug cable/key: http://www.plxtech.com/products/NET2000/NET20DC/default.asp - This is a small blue plastic connector with two USB connections, + This is a small blue plastic connector with two USB connections; it draws power from its USB connections. c.) You need a second client/console system with a high speed USB 2.0 port. - d.) The Netchip device must be plugged directly into the physical + d.) The NetChip device must be plugged directly into the physical debug port on the "host/target" system. You cannot use a USB hub in between the physical debug port and the "host/target" system. The EHCI debug controller is bound to a specific physical USB - port and the Netchip device will only work as an early printk + port and the NetChip device will only work as an early printk device in this port. The EHCI host controllers are electrically wired such that the EHCI debug controller is hooked up to the - first physical and there is no way to change this via software. + first physical port and there is no way to change this via software. You can find the physical port through experimentation by trying each physical port on the system and rebooting. Or you can try and use lsusb or look at the kernel info messages emitted by the @@ -65,9 +65,9 @@ and two USB cables, connected like this: to the hardware vendor, because there is no reason not to wire this port into one of the physically accessible ports. - e.) It is also important to note, that many versions of the Netchip + e.) It is also important to note, that many versions of the NetChip device require the "client/console" system to be plugged into the - right and side of the device (with the product logo facing up and + right hand side of the device (with the product logo facing up and readable left to right). The reason being is that the 5 volt power supply is taken from only one side of the device and it must be the side that does not get rebooted. @@ -81,13 +81,18 @@ and two USB cables, connected like this: CONFIG_EARLY_PRINTK_DBGP=y And you need to add the boot command line: "earlyprintk=dbgp". + (If you are using Grub, append it to the 'kernel' line in - /etc/grub.conf) + /etc/grub.conf. If you are using Grub2 on a BIOS firmware system, + append it to the 'linux' line in /boot/grub2/grub.cfg. If you are + using Grub2 on an EFI firmware system, append it to the 'linux' + or 'linuxefi' line in /boot/grub2/grub.cfg or + /boot/efi/EFI//grub.cfg.) On systems with more than one EHCI debug controller you must specify the correct EHCI debug controller number. The ordering comes from the PCI bus enumeration of the EHCI controllers. The - default with no number argument is "0" the first EHCI debug + default with no number argument is "0" or the first EHCI debug controller. To use the second EHCI debug controller, you would use the command line: "earlyprintk=dbgp1" @@ -111,7 +116,7 @@ and two USB cables, connected like this: see the raw output. c.) On Nvidia Southbridge based systems: the kernel will try to probe - and find out which port has debug device connected. + and find out which port has a debug device connected. 3. Testing that it works fine: