[POWERPC] mpc5200 device tree bindings refinement
Much needed refinement of mpc5200 device tree binding specifications. Short list: - drop mpc52xx designator; only two supported chips exist, 5200 and 5200b. It's premature to refer to them as '52xx'. - Specify optional 'model' and 'revision' properties in the soc5200 node - Specify reqiured 'cell-index' property to identify between multiple SOC devices of the same type. (Useful for arbitrating shared register access) - Specify optional 'port-number' property for adjusting the logical serial port assignments. - Specify optional 'has-wdt' property for gpt0 node. - Add system-frequency property to soc5200 node Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
This commit is contained in:
Grant Likely
Paul Mackerras
parent
e3aba81d15
commit
05cbbc692f
|
|
@ -1,7 +1,7 @@
|
|||
MPC52xx Device Tree Bindings
|
||||
MPC5200 Device Tree Bindings
|
||||
----------------------------
|
||||
|
||||
(c) 2006 Secret Lab Technologies Ltd
|
||||
(c) 2006-2007 Secret Lab Technologies Ltd
|
||||
Grant Likely <grant.likely at secretlab.ca>
|
||||
|
||||
********** DRAFT ***********
|
||||
|
|
@ -20,11 +20,11 @@ described in Documentation/powerpc/booting-without-of.txt), or passed
|
|||
by Open Firmare (IEEE 1275) compatible firmware using an OF compatible
|
||||
client interface API.
|
||||
|
||||
This document specifies the requirements on the device-tree for mpc52xx
|
||||
This document specifies the requirements on the device-tree for mpc5200
|
||||
based boards. These requirements are above and beyond the details
|
||||
specified in either the OpenFirmware spec or booting-without-of.txt
|
||||
|
||||
All new mpc52xx-based boards are expected to match this document. In
|
||||
All new mpc5200-based boards are expected to match this document. In
|
||||
cases where this document is not sufficient to support a new board port,
|
||||
this document should be updated as part of adding the new board support.
|
||||
|
||||
|
|
@ -32,26 +32,26 @@ II - Philosophy
|
|||
===============
|
||||
The core of this document is naming convention. The whole point of
|
||||
defining this convention is to reduce or eliminate the number of
|
||||
special cases required to support a 52xx board. If all 52xx boards
|
||||
follow the same convention, then generic 52xx support code will work
|
||||
special cases required to support a 5200 board. If all 5200 boards
|
||||
follow the same convention, then generic 5200 support code will work
|
||||
rather than coding special cases for each new board.
|
||||
|
||||
This section tries to capture the thought process behind why the naming
|
||||
convention is what it is.
|
||||
|
||||
1. Node names
|
||||
-------------
|
||||
1. names
|
||||
---------
|
||||
There is strong convention/requirements already established for children
|
||||
of the root node. 'cpus' describes the processor cores, 'memory'
|
||||
describes memory, and 'chosen' provides boot configuration. Other nodes
|
||||
are added to describe devices attached to the processor local bus.
|
||||
Following convention already established with other system-on-chip
|
||||
processors, MPC52xx boards must have an 'soc5200' node as a child of the
|
||||
root node.
|
||||
|
||||
The soc5200 node holds child nodes for all on chip devices. Child nodes
|
||||
are typically named after the configured function. ie. the FEC node is
|
||||
named 'ethernet', and a PSC in uart mode is named 'serial'.
|
||||
Following convention already established with other system-on-chip
|
||||
processors, 5200 device trees should use the name 'soc5200' for the
|
||||
parent node of on chip devices, and the root node should be its parent.
|
||||
|
||||
Child nodes are typically named after the configured function. ie.
|
||||
the FEC node is named 'ethernet', and a PSC in uart mode is named 'serial'.
|
||||
|
||||
2. device_type property
|
||||
-----------------------
|
||||
|
|
@ -66,28 +66,47 @@ exactly.
|
|||
Since device_type isn't enough to match devices to drivers, there also
|
||||
needs to be a naming convention for the compatible property. Compatible
|
||||
is an list of device descriptions sorted from specific to generic. For
|
||||
the mpc52xx, the required format for each compatible value is
|
||||
<chip>-<device>[-<mode>]. At the minimum, the list shall contain two
|
||||
items; the first specifying the exact chip, and the second specifying
|
||||
mpc52xx for the chip.
|
||||
the mpc5200, the required format for each compatible value is
|
||||
<chip>-<device>[-<mode>]. The OS should be able to match a device driver
|
||||
to the device based solely on the compatible value. If two drivers
|
||||
match on the compatible list; the 'most compatible' driver should be
|
||||
selected.
|
||||
|
||||
ie. ethernet on mpc5200b: compatible = "mpc5200b-ethernet\0mpc52xx-ethernet"
|
||||
The split between the MPC5200 and the MPC5200B leaves a bit of a
|
||||
connundrum. How should the compatible property be set up to provide
|
||||
maximum compatability information; but still acurately describe the
|
||||
chip? For the MPC5200; the answer is easy. Most of the SoC devices
|
||||
originally appeared on the MPC5200. Since they didn't exist anywhere
|
||||
else; the 5200 compatible properties will contain only one item;
|
||||
"mpc5200-<device>".
|
||||
|
||||
The idea here is that most drivers will match to the most generic field
|
||||
in the compatible list (mpc52xx-*), but can also test the more specific
|
||||
field for enabling bug fixes or extra features.
|
||||
The 5200B is almost the same as the 5200, but not quite. It fixes
|
||||
silicon bugs and it adds a small number of enhancements. Most of the
|
||||
devices either provide exactly the same interface as on the 5200. A few
|
||||
devices have extra functions but still have a backwards compatible mode.
|
||||
To express this infomation as completely as possible, 5200B device trees
|
||||
should have two items in the compatible list;
|
||||
"mpc5200b-<device>\0mpc5200-<device>". It is *strongly* recommended
|
||||
that 5200B device trees follow this convention (instead of only listing
|
||||
the base mpc5200 item).
|
||||
|
||||
If another chip appear on the market with one of the mpc5200 SoC
|
||||
devices, then the compatible list should include mpc5200-<device>.
|
||||
|
||||
ie. ethernet on mpc5200: compatible = "mpc5200-ethernet"
|
||||
ethernet on mpc5200b: compatible = "mpc5200b-ethernet\0mpc5200-ethernet"
|
||||
|
||||
Modal devices, like PSCs, also append the configured function to the
|
||||
end of the compatible field. ie. A PSC in i2s mode would specify
|
||||
"mpc52xx-psc-i2s", not "mpc52xx-i2s". This convention is chosen to
|
||||
"mpc5200-psc-i2s", not "mpc5200-i2s". This convention is chosen to
|
||||
avoid naming conflicts with non-psc devices providing the same
|
||||
function. For example, "mpc52xx-spi" and "mpc52xx-psc-spi" describe
|
||||
function. For example, "mpc5200-spi" and "mpc5200-psc-spi" describe
|
||||
the mpc5200 simple spi device and a PSC spi mode respectively.
|
||||
|
||||
If the soc device is more generic and present on other SOCs, the
|
||||
compatible property can specify the more generic device type also.
|
||||
|
||||
ie. mscan: compatible = "mpc5200-mscan\0mpc52xx-mscan\0fsl,mscan";
|
||||
ie. mscan: compatible = "mpc5200-mscan\0fsl,mscan";
|
||||
|
||||
At the time of writing, exact chip may be either 'mpc5200' or
|
||||
'mpc5200b'.
|
||||
|
|
@ -96,7 +115,7 @@ Device drivers should always try to match as generically as possible.
|
|||
|
||||
III - Structure
|
||||
===============
|
||||
The device tree for an mpc52xx board follows the structure defined in
|
||||
The device tree for an mpc5200 board follows the structure defined in
|
||||
booting-without-of.txt with the following additional notes:
|
||||
|
||||
0) the root node
|
||||
|
|
@ -115,7 +134,7 @@ Typical memory description node; see booting-without-of.
|
|||
|
||||
3) The soc5200 node
|
||||
-------------------
|
||||
This node describes the on chip SOC peripherals. Every mpc52xx based
|
||||
This node describes the on chip SOC peripherals. Every mpc5200 based
|
||||
board will have this node, and as such there is a common naming
|
||||
convention for SOC devices.
|
||||
|
||||
|
|
@ -125,71 +144,111 @@ name type description
|
|||
device_type string must be "soc"
|
||||
ranges int should be <0 baseaddr baseaddr+10000>
|
||||
reg int must be <baseaddr 10000>
|
||||
compatible string mpc5200: "mpc5200-soc"
|
||||
mpc5200b: "mpc5200b-soc\0mpc5200-soc"
|
||||
system-frequency int Fsystem frequency; source of all
|
||||
other clocks.
|
||||
bus-frequency int IPB bus frequency in HZ. Clock rate
|
||||
used by most of the soc devices.
|
||||
#interrupt-cells int must be <3>.
|
||||
|
||||
Recommended properties:
|
||||
name type description
|
||||
---- ---- -----------
|
||||
compatible string should be "<chip>-soc\0mpc52xx-soc"
|
||||
ie. "mpc5200b-soc\0mpc52xx-soc"
|
||||
#interrupt-cells int must be <3>. If it is not defined
|
||||
here then it must be defined in every
|
||||
soc device node.
|
||||
bus-frequency int IPB bus frequency in HZ. Clock rate
|
||||
used by most of the soc devices.
|
||||
Defining it here avoids needing it
|
||||
added to every device node.
|
||||
model string Exact model of the chip;
|
||||
ie: model="fsl,mpc5200"
|
||||
revision string Silicon revision of chip
|
||||
ie: revision="M08A"
|
||||
|
||||
The 'model' and 'revision' properties are *strongly* recommended. Having
|
||||
them presence acts as a bit of a safety net for working around as yet
|
||||
undiscovered bugs on one version of silicon. For example, device drivers
|
||||
can use the model and revision properties to decide if a bug fix should
|
||||
be turned on.
|
||||
|
||||
4) soc5200 child nodes
|
||||
----------------------
|
||||
Any on chip SOC devices available to Linux must appear as soc5200 child nodes.
|
||||
|
||||
Note: in the tables below, '*' matches all <chip> values. ie.
|
||||
*-pic would translate to "mpc5200-pic\0mpc52xx-pic"
|
||||
Note: The tables below show the value for the mpc5200. A mpc5200b device
|
||||
tree should use the "mpc5200b-<device>\0mpc5200-<device> form.
|
||||
|
||||
Required soc5200 child nodes:
|
||||
name device_type compatible Description
|
||||
---- ----------- ---------- -----------
|
||||
cdm@<addr> cdm *-cmd Clock Distribution
|
||||
pic@<addr> interrupt-controller *-pic need an interrupt
|
||||
cdm@<addr> cdm mpc5200-cmd Clock Distribution
|
||||
pic@<addr> interrupt-controller mpc5200-pic need an interrupt
|
||||
controller to boot
|
||||
bestcomm@<addr> dma-controller *-bestcomm 52xx pic also requires
|
||||
the bestcomm device
|
||||
bestcomm@<addr> dma-controller mpc5200-bestcomm 5200 pic also requires
|
||||
the bestcomm device
|
||||
|
||||
Recommended soc5200 child nodes; populate as needed for your board
|
||||
name device_type compatible Description
|
||||
---- ----------- ---------- -----------
|
||||
gpt@<addr> gpt *-gpt General purpose timers
|
||||
rtc@<addr> rtc *-rtc Real time clock
|
||||
mscan@<addr> mscan *-mscan CAN bus controller
|
||||
pci@<addr> pci *-pci PCI bridge
|
||||
serial@<addr> serial *-psc-uart PSC in serial mode
|
||||
i2s@<addr> sound *-psc-i2s PSC in i2s mode
|
||||
ac97@<addr> sound *-psc-ac97 PSC in ac97 mode
|
||||
spi@<addr> spi *-psc-spi PSC in spi mode
|
||||
irda@<addr> irda *-psc-irda PSC in IrDA mode
|
||||
spi@<addr> spi *-spi MPC52xx spi device
|
||||
ethernet@<addr> network *-fec MPC52xx ethernet device
|
||||
ata@<addr> ata *-ata IDE ATA interface
|
||||
i2c@<addr> i2c *-i2c I2C controller
|
||||
usb@<addr> usb-ohci-be *-ohci,ohci-be USB controller
|
||||
xlb@<addr> xlb *-xlb XLB arbritrator
|
||||
name device_type compatible Description
|
||||
---- ----------- ---------- -----------
|
||||
gpt@<addr> gpt mpc5200-gpt General purpose timers
|
||||
rtc@<addr> rtc mpc5200-rtc Real time clock
|
||||
mscan@<addr> mscan mpc5200-mscan CAN bus controller
|
||||
pci@<addr> pci mpc5200-pci PCI bridge
|
||||
serial@<addr> serial mpc5200-psc-uart PSC in serial mode
|
||||
i2s@<addr> sound mpc5200-psc-i2s PSC in i2s mode
|
||||
ac97@<addr> sound mpc5200-psc-ac97 PSC in ac97 mode
|
||||
spi@<addr> spi mpc5200-psc-spi PSC in spi mode
|
||||
irda@<addr> irda mpc5200-psc-irda PSC in IrDA mode
|
||||
spi@<addr> spi mpc5200-spi MPC5200 spi device
|
||||
ethernet@<addr> network mpc5200-fec MPC5200 ethernet device
|
||||
ata@<addr> ata mpc5200-ata IDE ATA interface
|
||||
i2c@<addr> i2c mpc5200-i2c I2C controller
|
||||
usb@<addr> usb-ohci-be mpc5200-ohci,ohci-be USB controller
|
||||
xlb@<addr> xlb mpc5200-xlb XLB arbritrator
|
||||
|
||||
Important child node properties
|
||||
name type description
|
||||
---- ---- -----------
|
||||
cell-index int When multiple devices are present, is the
|
||||
index of the device in the hardware (ie. There
|
||||
are 6 PSC on the 5200 numbered PSC1 to PSC6)
|
||||
PSC1 has 'cell-index = <0>'
|
||||
PSC4 has 'cell-index = <3>'
|
||||
|
||||
5) General Purpose Timer nodes (child of soc5200 node)
|
||||
On the mpc5200 and 5200b, GPT0 has a watchdog timer function. If the board
|
||||
design supports the internal wdt, then the device node for GPT0 should
|
||||
include the empty property 'has-wdt'.
|
||||
|
||||
6) PSC nodes (child of soc5200 node)
|
||||
PSC nodes can define the optional 'port-number' property to force assignment
|
||||
order of serial ports. For example, PSC5 might be physically connected to
|
||||
the port labeled 'COM1' and PSC1 wired to 'COM1'. In this case, PSC5 would
|
||||
have a "port-number = <0>" property, and PSC1 would have "port-number = <1>".
|
||||
|
||||
PSC in i2s mode: The mpc5200 and mpc5200b PSCs are not compatible when in
|
||||
i2s mode. An 'mpc5200b-psc-i2s' node cannot include 'mpc5200-psc-i2s' in the
|
||||
compatible field.
|
||||
|
||||
IV - Extra Notes
|
||||
================
|
||||
|
||||
1. Interrupt mapping
|
||||
--------------------
|
||||
The mpc52xx pic driver splits hardware IRQ numbers into two levels. The
|
||||
The mpc5200 pic driver splits hardware IRQ numbers into two levels. The
|
||||
split reflects the layout of the PIC hardware itself, which groups
|
||||
interrupts into one of three groups; CRIT, MAIN or PERP. Also, the
|
||||
Bestcomm dma engine has it's own set of interrupt sources which are
|
||||
cascaded off of peripheral interrupt 0, which the driver interprets as a
|
||||
fourth group, SDMA.
|
||||
|
||||
The interrupts property for device nodes using the mpc52xx pic consists
|
||||
The interrupts property for device nodes using the mpc5200 pic consists
|
||||
of three cells; <L1 L2 level>
|
||||
|
||||
L1 := [CRIT=0, MAIN=1, PERP=2, SDMA=3]
|
||||
L2 := interrupt number; directly mapped from the value in the
|
||||
"ICTL PerStat, MainStat, CritStat Encoded Register"
|
||||
level := [LEVEL_HIGH=0, EDGE_RISING=1, EDGE_FALLING=2, LEVEL_LOW=3]
|
||||
|
||||
2. Shared registers
|
||||
-------------------
|
||||
Some SoC devices share registers between them. ie. the i2c devices use
|
||||
a single clock control register, and almost all device are affected by
|
||||
the port_config register. Devices which need to manipulate shared regs
|
||||
should look to the parent SoC node. The soc node is responsible
|
||||
for arbitrating all shared register access.
|
||||
|
|
|
|||
|
|
@ -1,7 +1,7 @@
|
|||
/*
|
||||
* Lite5200 board Device Tree Source
|
||||
*
|
||||
* Copyright 2006 Secret Lab Technologies Ltd.
|
||||
* Copyright 2006-2007 Secret Lab Technologies Ltd.
|
||||
* Grant Likely <grant.likely@secretlab.ca>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
|
|
@ -17,8 +17,9 @@
|
|||
*/
|
||||
|
||||
/ {
|
||||
model = "Lite5200";
|
||||
compatible = "lite5200\0lite52xx\0mpc5200\0mpc52xx";
|
||||
model = "fsl,lite5200";
|
||||
// revision = "1.0";
|
||||
compatible = "fsl,lite5200\0generic-mpc5200";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
|
|
@ -47,14 +48,17 @@
|
|||
};
|
||||
|
||||
soc5200@f0000000 {
|
||||
model = "fsl,mpc5200";
|
||||
revision = "" // from bootloader
|
||||
#interrupt-cells = <3>;
|
||||
device_type = "soc";
|
||||
ranges = <0 f0000000 f0010000>;
|
||||
reg = <f0000000 00010000>;
|
||||
bus-frequency = <0>; // from bootloader
|
||||
system-frequency = <0>; // from bootloader
|
||||
|
||||
cdm@200 {
|
||||
compatible = "mpc5200-cdm\0mpc52xx-cdm";
|
||||
compatible = "mpc5200-cdm";
|
||||
reg = <200 38>;
|
||||
};
|
||||
|
||||
|
|
@ -64,77 +68,86 @@
|
|||
interrupt-controller;
|
||||
#interrupt-cells = <3>;
|
||||
device_type = "interrupt-controller";
|
||||
compatible = "mpc5200-pic\0mpc52xx-pic";
|
||||
compatible = "mpc5200-pic";
|
||||
reg = <500 80>;
|
||||
built-in;
|
||||
};
|
||||
|
||||
gpt@600 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <0>;
|
||||
reg = <600 10>;
|
||||
interrupts = <1 9 0>;
|
||||
interrupt-parent = <500>;
|
||||
has-wdt;
|
||||
};
|
||||
|
||||
gpt@610 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <1>;
|
||||
reg = <610 10>;
|
||||
interrupts = <1 a 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@620 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <2>;
|
||||
reg = <620 10>;
|
||||
interrupts = <1 b 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@630 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <3>;
|
||||
reg = <630 10>;
|
||||
interrupts = <1 c 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@640 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <4>;
|
||||
reg = <640 10>;
|
||||
interrupts = <1 d 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@650 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <5>;
|
||||
reg = <650 10>;
|
||||
interrupts = <1 e 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@660 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <6>;
|
||||
reg = <660 10>;
|
||||
interrupts = <1 f 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@670 { // General Purpose Timer
|
||||
compatible = "mpc5200-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <7>;
|
||||
reg = <670 10>;
|
||||
interrupts = <1 10 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
rtc@800 { // Real time clock
|
||||
compatible = "mpc5200-rtc\0mpc52xx-rtc";
|
||||
compatible = "mpc5200-rtc";
|
||||
device_type = "rtc";
|
||||
reg = <800 100>;
|
||||
interrupts = <1 5 0 1 6 0>;
|
||||
|
|
@ -143,7 +156,8 @@
|
|||
|
||||
mscan@900 {
|
||||
device_type = "mscan";
|
||||
compatible = "mpc5200-mscan\0mpc52xx-mscan";
|
||||
compatible = "mpc5200-mscan";
|
||||
cell-index = <0>;
|
||||
interrupts = <2 11 0>;
|
||||
interrupt-parent = <500>;
|
||||
reg = <900 80>;
|
||||
|
|
@ -151,21 +165,22 @@
|
|||
|
||||
mscan@980 {
|
||||
device_type = "mscan";
|
||||
compatible = "mpc5200-mscan\0mpc52xx-mscan";
|
||||
compatible = "mpc5200-mscan";
|
||||
cell-index = <1>;
|
||||
interrupts = <1 12 0>;
|
||||
interrupt-parent = <500>;
|
||||
reg = <980 80>;
|
||||
};
|
||||
|
||||
gpio@b00 {
|
||||
compatible = "mpc5200-gpio\0mpc52xx-gpio";
|
||||
compatible = "mpc5200-gpio";
|
||||
reg = <b00 40>;
|
||||
interrupts = <1 7 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpio-wkup@b00 {
|
||||
compatible = "mpc5200-gpio-wkup\0mpc52xx-gpio-wkup";
|
||||
compatible = "mpc5200-gpio-wkup";
|
||||
reg = <c00 40>;
|
||||
interrupts = <1 8 0 0 3 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -176,7 +191,7 @@
|
|||
#size-cells = <2>;
|
||||
#address-cells = <3>;
|
||||
device_type = "pci";
|
||||
compatible = "mpc5200-pci\0mpc52xx-pci";
|
||||
compatible = "mpc5200-pci";
|
||||
reg = <d00 100>;
|
||||
interrupt-map-mask = <f800 0 0 7>;
|
||||
interrupt-map = <c000 0 0 1 500 0 0 3
|
||||
|
|
@ -194,7 +209,7 @@
|
|||
|
||||
spi@f00 {
|
||||
device_type = "spi";
|
||||
compatible = "mpc5200-spi\0mpc52xx-spi";
|
||||
compatible = "mpc5200-spi";
|
||||
reg = <f00 20>;
|
||||
interrupts = <2 d 0 2 e 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -202,7 +217,7 @@
|
|||
|
||||
usb@1000 {
|
||||
device_type = "usb-ohci-be";
|
||||
compatible = "mpc5200-ohci\0mpc52xx-ohci\0ohci-be";
|
||||
compatible = "mpc5200-ohci\0ohci-be";
|
||||
reg = <1000 ff>;
|
||||
interrupts = <2 6 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -210,7 +225,7 @@
|
|||
|
||||
bestcomm@1200 {
|
||||
device_type = "dma-controller";
|
||||
compatible = "mpc5200-bestcomm\0mpc52xx-bestcomm";
|
||||
compatible = "mpc5200-bestcomm";
|
||||
reg = <1200 80>;
|
||||
interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
|
||||
3 4 0 3 5 0 3 6 0 3 7 0
|
||||
|
|
@ -220,67 +235,73 @@
|
|||
};
|
||||
|
||||
xlb@1f00 {
|
||||
compatible = "mpc5200-xlb\0mpc52xx-xlb";
|
||||
compatible = "mpc5200-xlb";
|
||||
reg = <1f00 100>;
|
||||
};
|
||||
|
||||
serial@2000 { // PSC1
|
||||
device_type = "serial";
|
||||
compatible = "mpc5200-psc-uart\0mpc52xx-psc-uart";
|
||||
compatible = "mpc5200-psc-uart";
|
||||
port-number = <0>; // Logical port assignment
|
||||
cell-index = <0>;
|
||||
reg = <2000 100>;
|
||||
interrupts = <2 1 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
// PSC2 in spi mode example
|
||||
spi@2200 { // PSC2
|
||||
device_type = "spi";
|
||||
compatible = "mpc5200-psc-spi\0mpc52xx-psc-spi";
|
||||
reg = <2200 100>;
|
||||
interrupts = <2 2 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
// PSC2 in ac97 mode example
|
||||
//ac97@2200 { // PSC2
|
||||
// device_type = "sound";
|
||||
// compatible = "mpc5200-psc-ac97";
|
||||
// cell-index = <1>;
|
||||
// reg = <2200 100>;
|
||||
// interrupts = <2 2 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC3 in CODEC mode example
|
||||
i2s@2400 { // PSC3
|
||||
device_type = "sound";
|
||||
compatible = "mpc5200-psc-i2s\0mpc52xx-psc-i2s";
|
||||
reg = <2400 100>;
|
||||
interrupts = <2 3 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
//i2s@2400 { // PSC3
|
||||
// device_type = "sound";
|
||||
// compatible = "mpc5200-psc-i2s";
|
||||
// cell-index = <2>;
|
||||
// reg = <2400 100>;
|
||||
// interrupts = <2 3 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC4 unconfigured
|
||||
// PSC4 in uart mode example
|
||||
//serial@2600 { // PSC4
|
||||
// device_type = "serial";
|
||||
// compatible = "mpc5200-psc-uart\0mpc52xx-psc-uart";
|
||||
// compatible = "mpc5200-psc-uart";
|
||||
// cell-index = <3>;
|
||||
// reg = <2600 100>;
|
||||
// interrupts = <2 b 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC5 unconfigured
|
||||
// PSC5 in uart mode example
|
||||
//serial@2800 { // PSC5
|
||||
// device_type = "serial";
|
||||
// compatible = "mpc5200-psc-uart\0mpc52xx-psc-uart";
|
||||
// compatible = "mpc5200-psc-uart";
|
||||
// cell-index = <4>;
|
||||
// reg = <2800 100>;
|
||||
// interrupts = <2 c 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC6 in AC97 mode example
|
||||
ac97@2c00 { // PSC6
|
||||
device_type = "sound";
|
||||
compatible = "mpc5200-psc-ac97\0mpc52xx-psc-ac97";
|
||||
reg = <2c00 100>;
|
||||
interrupts = <2 4 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
// PSC6 in spi mode example
|
||||
//spi@2c00 { // PSC6
|
||||
// device_type = "spi";
|
||||
// compatible = "mpc5200-psc-spi";
|
||||
// cell-index = <5>;
|
||||
// reg = <2c00 100>;
|
||||
// interrupts = <2 4 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
ethernet@3000 {
|
||||
device_type = "network";
|
||||
compatible = "mpc5200-fec\0mpc52xx-fec";
|
||||
compatible = "mpc5200-fec";
|
||||
reg = <3000 800>;
|
||||
mac-address = [ 02 03 04 05 06 07 ]; // Bad!
|
||||
interrupts = <2 5 0>;
|
||||
|
|
@ -289,7 +310,7 @@
|
|||
|
||||
ata@3a00 {
|
||||
device_type = "ata";
|
||||
compatible = "mpc5200-ata\0mpc52xx-ata";
|
||||
compatible = "mpc5200-ata";
|
||||
reg = <3a00 100>;
|
||||
interrupts = <2 7 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -297,7 +318,8 @@
|
|||
|
||||
i2c@3d00 {
|
||||
device_type = "i2c";
|
||||
compatible = "mpc5200-i2c\0mpc52xx-i2c";
|
||||
compatible = "mpc5200-i2c";
|
||||
cell-index = <0>;
|
||||
reg = <3d00 40>;
|
||||
interrupts = <2 f 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -305,14 +327,15 @@
|
|||
|
||||
i2c@3d40 {
|
||||
device_type = "i2c";
|
||||
compatible = "mpc5200-i2c\0mpc52xx-i2c";
|
||||
compatible = "mpc5200-i2c";
|
||||
cell-index = <1>;
|
||||
reg = <3d40 40>;
|
||||
interrupts = <2 10 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
sram@8000 {
|
||||
device_type = "sram";
|
||||
compatible = "mpc5200-sram\0mpc52xx-sram\0sram";
|
||||
compatible = "mpc5200-sram\0sram";
|
||||
reg = <8000 4000>;
|
||||
};
|
||||
};
|
||||
|
|
|
|||
|
|
@ -1,7 +1,7 @@
|
|||
/*
|
||||
* Lite5200B board Device Tree Source
|
||||
*
|
||||
* Copyright 2006 Secret Lab Technologies Ltd.
|
||||
* Copyright 2006-2007 Secret Lab Technologies Ltd.
|
||||
* Grant Likely <grant.likely@secretlab.ca>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
|
|
@ -17,8 +17,9 @@
|
|||
*/
|
||||
|
||||
/ {
|
||||
model = "Lite5200b";
|
||||
compatible = "lite5200b\0lite52xx\0mpc5200b\0mpc52xx";
|
||||
model = "fsl,lite5200b";
|
||||
// revision = "1.0";
|
||||
compatible = "fsl,lite5200b\0generic-mpc5200";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
|
|
@ -47,14 +48,17 @@
|
|||
};
|
||||
|
||||
soc5200@f0000000 {
|
||||
model = "fsl,mpc5200b";
|
||||
revision = ""; // from bootloader
|
||||
#interrupt-cells = <3>;
|
||||
device_type = "soc";
|
||||
ranges = <0 f0000000 f0010000>;
|
||||
reg = <f0000000 00010000>;
|
||||
bus-frequency = <0>; // from bootloader
|
||||
system-frequency = <0>; // from bootloader
|
||||
|
||||
cdm@200 {
|
||||
compatible = "mpc5200b-cdm\0mpc52xx-cdm";
|
||||
compatible = "mpc5200b-cdm\0mpc5200-cdm";
|
||||
reg = <200 38>;
|
||||
};
|
||||
|
||||
|
|
@ -64,77 +68,86 @@
|
|||
interrupt-controller;
|
||||
#interrupt-cells = <3>;
|
||||
device_type = "interrupt-controller";
|
||||
compatible = "mpc5200b-pic\0mpc52xx-pic";
|
||||
compatible = "mpc5200b-pic\0mpc5200-pic";
|
||||
reg = <500 80>;
|
||||
built-in;
|
||||
};
|
||||
|
||||
gpt@600 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <0>;
|
||||
reg = <600 10>;
|
||||
interrupts = <1 9 0>;
|
||||
interrupt-parent = <500>;
|
||||
has-wdt;
|
||||
};
|
||||
|
||||
gpt@610 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <1>;
|
||||
reg = <610 10>;
|
||||
interrupts = <1 a 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@620 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <2>;
|
||||
reg = <620 10>;
|
||||
interrupts = <1 b 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@630 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <3>;
|
||||
reg = <630 10>;
|
||||
interrupts = <1 c 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@640 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <4>;
|
||||
reg = <640 10>;
|
||||
interrupts = <1 d 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@650 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <5>;
|
||||
reg = <650 10>;
|
||||
interrupts = <1 e 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@660 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <6>;
|
||||
reg = <660 10>;
|
||||
interrupts = <1 f 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpt@670 { // General Purpose Timer
|
||||
compatible = "mpc5200b-gpt\0mpc52xx-gpt";
|
||||
compatible = "mpc5200b-gpt\0mpc5200-gpt";
|
||||
device_type = "gpt";
|
||||
cell-index = <7>;
|
||||
reg = <670 10>;
|
||||
interrupts = <1 10 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
rtc@800 { // Real time clock
|
||||
compatible = "mpc5200b-rtc\0mpc52xx-rtc";
|
||||
compatible = "mpc5200b-rtc\0mpc5200-rtc";
|
||||
device_type = "rtc";
|
||||
reg = <800 100>;
|
||||
interrupts = <1 5 0 1 6 0>;
|
||||
|
|
@ -143,7 +156,8 @@
|
|||
|
||||
mscan@900 {
|
||||
device_type = "mscan";
|
||||
compatible = "mpc5200b-mscan\0mpc52xx-mscan";
|
||||
compatible = "mpc5200b-mscan\0mpc5200-mscan";
|
||||
cell-index = <0>;
|
||||
interrupts = <2 11 0>;
|
||||
interrupt-parent = <500>;
|
||||
reg = <900 80>;
|
||||
|
|
@ -151,21 +165,22 @@
|
|||
|
||||
mscan@980 {
|
||||
device_type = "mscan";
|
||||
compatible = "mpc5200b-mscan\0mpc52xx-mscan";
|
||||
compatible = "mpc5200b-mscan\0mpc5200-mscan";
|
||||
cell-index = <1>;
|
||||
interrupts = <1 12 0>;
|
||||
interrupt-parent = <500>;
|
||||
reg = <980 80>;
|
||||
};
|
||||
|
||||
gpio@b00 {
|
||||
compatible = "mpc5200b-gpio\0mpc52xx-gpio";
|
||||
compatible = "mpc5200b-gpio\0mpc5200-gpio";
|
||||
reg = <b00 40>;
|
||||
interrupts = <1 7 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
gpio-wkup@b00 {
|
||||
compatible = "mpc5200b-gpio-wkup\0mpc52xx-gpio-wkup";
|
||||
compatible = "mpc5200b-gpio-wkup\0mpc5200-gpio-wkup";
|
||||
reg = <c00 40>;
|
||||
interrupts = <1 8 0 0 3 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -176,7 +191,7 @@
|
|||
#size-cells = <2>;
|
||||
#address-cells = <3>;
|
||||
device_type = "pci";
|
||||
compatible = "mpc5200b-pci\0mpc52xx-pci";
|
||||
compatible = "mpc5200b-pci\0mpc5200-pci";
|
||||
reg = <d00 100>;
|
||||
interrupt-map-mask = <f800 0 0 7>;
|
||||
interrupt-map = <c000 0 0 1 500 0 0 3 // 1st slot
|
||||
|
|
@ -199,7 +214,7 @@
|
|||
|
||||
spi@f00 {
|
||||
device_type = "spi";
|
||||
compatible = "mpc5200b-spi\0mpc52xx-spi";
|
||||
compatible = "mpc5200b-spi\0mpc5200-spi";
|
||||
reg = <f00 20>;
|
||||
interrupts = <2 d 0 2 e 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -207,7 +222,7 @@
|
|||
|
||||
usb@1000 {
|
||||
device_type = "usb-ohci-be";
|
||||
compatible = "mpc5200b-ohci\0mpc52xx-ohci\0ohci-be";
|
||||
compatible = "mpc5200b-ohci\0mpc5200-ohci\0ohci-be";
|
||||
reg = <1000 ff>;
|
||||
interrupts = <2 6 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -215,7 +230,7 @@
|
|||
|
||||
bestcomm@1200 {
|
||||
device_type = "dma-controller";
|
||||
compatible = "mpc5200b-bestcomm\0mpc52xx-bestcomm";
|
||||
compatible = "mpc5200b-bestcomm\0mpc5200-bestcomm";
|
||||
reg = <1200 80>;
|
||||
interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
|
||||
3 4 0 3 5 0 3 6 0 3 7 0
|
||||
|
|
@ -225,67 +240,73 @@
|
|||
};
|
||||
|
||||
xlb@1f00 {
|
||||
compatible = "mpc5200b-xlb\0mpc52xx-xlb";
|
||||
compatible = "mpc5200b-xlb\0mpc5200-xlb";
|
||||
reg = <1f00 100>;
|
||||
};
|
||||
|
||||
serial@2000 { // PSC1
|
||||
device_type = "serial";
|
||||
compatible = "mpc5200b-psc-uart\0mpc52xx-psc-uart";
|
||||
compatible = "mpc5200b-psc-uart\0mpc5200-psc-uart";
|
||||
port-number = <0>; // Logical port assignment
|
||||
cell-index = <0>;
|
||||
reg = <2000 100>;
|
||||
interrupts = <2 1 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
|
||||
// PSC2 in spi mode example
|
||||
spi@2200 { // PSC2
|
||||
device_type = "spi";
|
||||
compatible = "mpc5200b-psc-spi\0mpc52xx-psc-spi";
|
||||
reg = <2200 100>;
|
||||
interrupts = <2 2 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
// PSC2 in ac97 mode example
|
||||
//ac97@2200 { // PSC2
|
||||
// device_type = "sound";
|
||||
// compatible = "mpc5200b-psc-ac97\0mpc5200-psc-ac97";
|
||||
// cell-index = <1>;
|
||||
// reg = <2200 100>;
|
||||
// interrupts = <2 2 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC3 in CODEC mode example
|
||||
i2s@2400 { // PSC3
|
||||
device_type = "sound";
|
||||
compatible = "mpc5200b-psc-i2s\0mpc52xx-psc-i2s";
|
||||
reg = <2400 100>;
|
||||
interrupts = <2 3 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
//i2s@2400 { // PSC3
|
||||
// device_type = "sound";
|
||||
// compatible = "mpc5200b-psc-i2s"; //not 5200 compatible
|
||||
// cell-index = <2>;
|
||||
// reg = <2400 100>;
|
||||
// interrupts = <2 3 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC4 unconfigured
|
||||
// PSC4 in uart mode example
|
||||
//serial@2600 { // PSC4
|
||||
// device_type = "serial";
|
||||
// compatible = "mpc5200b-psc-uart\0mpc52xx-psc-uart";
|
||||
// compatible = "mpc5200b-psc-uart\0mpc5200-psc-uart";
|
||||
// cell-index = <3>;
|
||||
// reg = <2600 100>;
|
||||
// interrupts = <2 b 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC5 unconfigured
|
||||
// PSC5 in uart mode example
|
||||
//serial@2800 { // PSC5
|
||||
// device_type = "serial";
|
||||
// compatible = "mpc5200b-psc-uart\0mpc52xx-psc-uart";
|
||||
// compatible = "mpc5200b-psc-uart\0mpc5200-psc-uart";
|
||||
// cell-index = <4>;
|
||||
// reg = <2800 100>;
|
||||
// interrupts = <2 c 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
// PSC6 in AC97 mode example
|
||||
ac97@2c00 { // PSC6
|
||||
device_type = "sound";
|
||||
compatible = "mpc5200b-psc-ac97\0mpc52xx-psc-ac97";
|
||||
reg = <2c00 100>;
|
||||
interrupts = <2 4 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
// PSC6 in spi mode example
|
||||
//spi@2c00 { // PSC6
|
||||
// device_type = "spi";
|
||||
// compatible = "mpc5200b-psc-spi\0mpc5200-psc-spi";
|
||||
// cell-index = <5>;
|
||||
// reg = <2c00 100>;
|
||||
// interrupts = <2 4 0>;
|
||||
// interrupt-parent = <500>;
|
||||
//};
|
||||
|
||||
ethernet@3000 {
|
||||
device_type = "network";
|
||||
compatible = "mpc5200b-fec\0mpc52xx-fec";
|
||||
compatible = "mpc5200b-fec\0mpc5200-fec";
|
||||
reg = <3000 800>;
|
||||
mac-address = [ 02 03 04 05 06 07 ]; // Bad!
|
||||
interrupts = <2 5 0>;
|
||||
|
|
@ -294,7 +315,7 @@
|
|||
|
||||
ata@3a00 {
|
||||
device_type = "ata";
|
||||
compatible = "mpc5200b-ata\0mpc52xx-ata";
|
||||
compatible = "mpc5200b-ata\0mpc5200-ata";
|
||||
reg = <3a00 100>;
|
||||
interrupts = <2 7 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -302,7 +323,8 @@
|
|||
|
||||
i2c@3d00 {
|
||||
device_type = "i2c";
|
||||
compatible = "mpc5200b-i2c\0mpc52xx-i2c";
|
||||
compatible = "mpc5200b-i2c\0mpc5200-i2c";
|
||||
cell-index = <0>;
|
||||
reg = <3d00 40>;
|
||||
interrupts = <2 f 0>;
|
||||
interrupt-parent = <500>;
|
||||
|
|
@ -310,14 +332,15 @@
|
|||
|
||||
i2c@3d40 {
|
||||
device_type = "i2c";
|
||||
compatible = "mpc5200b-i2c\0mpc52xx-i2c";
|
||||
compatible = "mpc5200b-i2c\0mpc5200-i2c";
|
||||
cell-index = <1>;
|
||||
reg = <3d40 40>;
|
||||
interrupts = <2 10 0>;
|
||||
interrupt-parent = <500>;
|
||||
};
|
||||
sram@8000 {
|
||||
device_type = "sram";
|
||||
compatible = "mpc5200b-sram\0mpc52xx-sram\0sram";
|
||||
compatible = "mpc5200b-sram\0mpc5200-sram\0sram";
|
||||
reg = <8000 4000>;
|
||||
};
|
||||
};
|
||||
|
|
|
|||
Loading…
Reference in New Issue