clk: sunxi-ng: Add driver for A83T CCU

The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.

Like the A80, the SoC does not have a low speed 32.768 kHz oscillator.
Unlike the A80, there is no clock input either. The only low speed clock
available is the internal oscillator which runs at around 16 MHz,
divided by 512, yielding a low speed clock around 31.250 kHz.

Also, the MMC2 module clock supports switching to a "new timing" mode.
This mode divides the clock output by half, and disables the CCU based
clock delays. The MMC controller must be configure to the same mode,
and then use its internal clock delays.

This driver does not support runtime switching of the timing modes.
Instead, the new timing mode is enforced at probe time. Consumers can
check which mode is active by trying to get the current phase delay
of the MMC2 phase clocks, which will return -ENOTSUPP if the new
timing mode is active.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit is contained in:
Chen-Yu Tsai 2017-05-19 15:06:09 +08:00 committed by Maxime Ripard
parent 13e0dde8b2
commit 05359be117
6 changed files with 1236 additions and 0 deletions

View File

@ -116,6 +116,17 @@ config SUN8I_A33_CCU
default MACH_SUN8I
depends on MACH_SUN8I || COMPILE_TEST
config SUN8I_A83T_CCU
bool "Support for the Allwinner A83T CCU"
select SUNXI_CCU_DIV
select SUNXI_CCU_GATE
select SUNXI_CCU_MP
select SUNXI_CCU_MUX
select SUNXI_CCU_NKMP
select SUNXI_CCU_NM
select SUNXI_CCU_PHASE
default MACH_SUN8I
config SUN8I_H3_CCU
bool "Support for the Allwinner H3 CCU"
select SUNXI_CCU_DIV

View File

@ -23,6 +23,7 @@ obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
obj-$(CONFIG_SUN8I_A83T_CCU) += ccu-sun8i-a83t.o
obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
obj-$(CONFIG_SUN8I_DE2_CCU) += ccu-sun8i-de2.o

View File

@ -0,0 +1,922 @@
/*
* Copyright (c) 2017 Chen-Yu Tsai. All rights reserved.
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/clk-provider.h>
#include <linux/of_address.h>
#include <linux/platform_device.h>
#include "ccu_common.h"
#include "ccu_reset.h"
#include "ccu_div.h"
#include "ccu_gate.h"
#include "ccu_mp.h"
#include "ccu_mux.h"
#include "ccu_nkmp.h"
#include "ccu_nm.h"
#include "ccu_phase.h"
#include "ccu-sun8i-a83t.h"
#define CCU_SUN8I_A83T_LOCK_REG 0x208
/*
* The CPU PLLs are actually NP clocks, with P being /1 or /4. However
* P should only be used for output frequencies lower than 228 MHz.
* Neither mainline Linux, U-boot, nor the vendor BSPs use these.
*
* For now we can just model it as a multiplier clock, and force P to /1.
*/
#define SUN8I_A83T_PLL_C0CPUX_REG 0x000
#define SUN8I_A83T_PLL_C1CPUX_REG 0x004
static struct ccu_mult pll_c0cpux_clk = {
.enable = BIT(31),
.lock = BIT(0),
.mult = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.common = {
.reg = SUN8I_A83T_PLL_C0CPUX_REG,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-c0cpux", "osc24M",
&ccu_mult_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_mult pll_c1cpux_clk = {
.enable = BIT(31),
.lock = BIT(1),
.mult = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.common = {
.reg = SUN8I_A83T_PLL_C1CPUX_REG,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-c1cpux", "osc24M",
&ccu_mult_ops,
CLK_SET_RATE_UNGATE),
},
};
/*
* The Audio PLL has d1, d2 dividers in addition to the usual N, M
* factors. Since we only need 2 frequencies from this PLL: 22.5792 MHz
* and 24.576 MHz, ignore them for now. Enforce the default for them,
* which is d1 = 0, d2 = 1.
*/
#define SUN8I_A83T_PLL_AUDIO_REG 0x008
static struct ccu_nm pll_audio_clk = {
.enable = BIT(31),
.lock = BIT(2),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV_OFFSET(0, 6, 0),
.common = {
.reg = SUN8I_A83T_PLL_AUDIO_REG,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-audio", "osc24M",
&ccu_nm_ops, CLK_SET_RATE_UNGATE),
},
};
/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
static struct ccu_nkmp pll_video0_clk = {
.enable = BIT(31),
.lock = BIT(3),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(0, 2), /* output divider */
.common = {
.reg = 0x010,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-video0", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_ve_clk = {
.enable = BIT(31),
.lock = BIT(4),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(18, 1), /* output divider */
.common = {
.reg = 0x018,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-ve", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_ddr_clk = {
.enable = BIT(31),
.lock = BIT(5),
.n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(18, 1), /* output divider */
.common = {
.reg = 0x020,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-ddr", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_periph_clk = {
.enable = BIT(31),
.lock = BIT(6),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(18, 1), /* output divider */
.common = {
.reg = 0x028,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-periph", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_gpu_clk = {
.enable = BIT(31),
.lock = BIT(7),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(18, 1), /* output divider */
.common = {
.reg = 0x038,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-gpu", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_hsic_clk = {
.enable = BIT(31),
.lock = BIT(8),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(18, 1), /* output divider */
.common = {
.reg = 0x044,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-hsic", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_de_clk = {
.enable = BIT(31),
.lock = BIT(9),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(18, 1), /* output divider */
.common = {
.reg = 0x048,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-de", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static struct ccu_nkmp pll_video1_clk = {
.enable = BIT(31),
.lock = BIT(10),
.n = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(8, 8, 0, 12, 0),
.m = _SUNXI_CCU_DIV(16, 1), /* input divider */
.p = _SUNXI_CCU_DIV(0, 2), /* external divider p */
.common = {
.reg = 0x04c,
.lock_reg = CCU_SUN8I_A83T_LOCK_REG,
.features = CCU_FEATURE_LOCK_REG,
.hw.init = CLK_HW_INIT("pll-video1", "osc24M",
&ccu_nkmp_ops,
CLK_SET_RATE_UNGATE),
},
};
static const char * const c0cpux_parents[] = { "osc24M", "pll-c0cpux" };
static SUNXI_CCU_MUX(c0cpux_clk, "c0cpux", c0cpux_parents,
0x50, 12, 1, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
static const char * const c1cpux_parents[] = { "osc24M", "pll-c1cpux" };
static SUNXI_CCU_MUX(c1cpux_clk, "c1cpux", c1cpux_parents,
0x50, 28, 1, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
static SUNXI_CCU_M(axi0_clk, "axi0", "c0cpux", 0x050, 0, 2, 0);
static SUNXI_CCU_M(axi1_clk, "axi1", "c1cpux", 0x050, 16, 2, 0);
static const char * const ahb1_parents[] = { "osc16M-d512", "osc24M",
"pll-periph",
"pll-periph" };
static const struct ccu_mux_var_prediv ahb1_predivs[] = {
{ .index = 2, .shift = 6, .width = 2 },
{ .index = 3, .shift = 6, .width = 2 },
};
static struct ccu_div ahb1_clk = {
.div = _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
.mux = {
.shift = 12,
.width = 2,
.var_predivs = ahb1_predivs,
.n_var_predivs = ARRAY_SIZE(ahb1_predivs),
},
.common = {
.reg = 0x054,
.hw.init = CLK_HW_INIT_PARENTS("ahb1",
ahb1_parents,
&ccu_div_ops,
0),
},
};
static SUNXI_CCU_M(apb1_clk, "apb1", "ahb1", 0x054, 8, 2, 0);
static const char * const apb2_parents[] = { "osc16M-d512", "osc24M",
"pll-periph", "pll-periph" };
static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", apb2_parents, 0x058,
0, 5, /* M */
16, 2, /* P */
24, 2, /* mux */
0);
static const char * const ahb2_parents[] = { "ahb1", "pll-periph" };
static const struct ccu_mux_fixed_prediv ahb2_prediv = {
.index = 1, .div = 2
};
static struct ccu_mux ahb2_clk = {
.mux = {
.shift = 0,
.width = 2,
.fixed_predivs = &ahb2_prediv,
.n_predivs = 1,
},
.common = {
.reg = 0x05c,
.hw.init = CLK_HW_INIT_PARENTS("ahb2",
ahb2_parents,
&ccu_mux_ops,
0),
},
};
static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb1",
0x060, BIT(1), 0);
static SUNXI_CCU_GATE(bus_ss_clk, "bus-ss", "ahb1",
0x060, BIT(5), 0);
static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "ahb1",
0x060, BIT(6), 0);
static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb1",
0x060, BIT(8), 0);
static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb1",
0x060, BIT(9), 0);
static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb1",
0x060, BIT(10), 0);
static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb1",
0x060, BIT(13), 0);
static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "ahb1",
0x060, BIT(14), 0);
static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb2",
0x060, BIT(17), 0);
static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "ahb1",
0x060, BIT(19), 0);
static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb1",
0x060, BIT(20), 0);
static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb1",
0x060, BIT(21), 0);
static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb1",
0x060, BIT(24), 0);
static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb2",
0x060, BIT(26), 0);
static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb2",
0x060, BIT(27), 0);
static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb2",
0x060, BIT(29), 0);
static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "ahb1",
0x064, BIT(0), 0);
static SUNXI_CCU_GATE(bus_tcon0_clk, "bus-tcon0", "ahb1",
0x064, BIT(4), 0);
static SUNXI_CCU_GATE(bus_tcon1_clk, "bus-tcon1", "ahb1",
0x064, BIT(5), 0);
static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb1",
0x064, BIT(8), 0);
static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb1",
0x064, BIT(11), 0);
static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "ahb1",
0x064, BIT(12), 0);
static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "ahb1",
0x064, BIT(20), 0);
static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "ahb1",
0x064, BIT(21), 0);
static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "ahb1",
0x064, BIT(22), 0);
static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1",
0x068, BIT(1), 0);
static SUNXI_CCU_GATE(bus_pio_clk, "bus-pio", "apb1",
0x068, BIT(5), 0);
static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1",
0x068, BIT(12), 0);
static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1",
0x068, BIT(13), 0);
static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1",
0x068, BIT(14), 0);
static SUNXI_CCU_GATE(bus_tdm_clk, "bus-tdm", "apb1",
0x068, BIT(15), 0);
static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2",
0x06c, BIT(0), 0);
static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2",
0x06c, BIT(0), 0);
static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2",
0x06c, BIT(0), 0);
static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2",
0x06c, BIT(16), 0);
static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2",
0x06c, BIT(17), 0);
static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2",
0x06c, BIT(20), 0);
static const char * const cci400_parents[] = { "osc24M", "pll-periph",
"pll-hsic" };
static struct ccu_div cci400_clk = {
.div = _SUNXI_CCU_DIV_FLAGS(0, 2, 0),
.mux = _SUNXI_CCU_MUX(24, 2),
.common = {
.reg = 0x078,
.hw.init = CLK_HW_INIT_PARENTS("cci400",
cci400_parents,
&ccu_div_ops,
CLK_IS_CRITICAL),
},
};
static const char * const mod0_default_parents[] = { "osc24M", "pll-periph" };
static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand", mod0_default_parents,
0x080,
0, 4, /* M */
16, 2, /* P */
24, 2, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mod0_default_parents,
0x088,
0, 4, /* M */
16, 2, /* P */
24, 2, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_PHASE(mmc0_sample_clk, "mmc0-sample", "mmc0",
0x088, 20, 3, 0);
static SUNXI_CCU_PHASE(mmc0_output_clk, "mmc0-output", "mmc0",
0x088, 8, 3, 0);
static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mod0_default_parents,
0x08c,
0, 4, /* M */
16, 2, /* P */
24, 2, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_PHASE(mmc1_sample_clk, "mmc1-sample", "mmc1",
0x08c, 20, 3, 0);
static SUNXI_CCU_PHASE(mmc1_output_clk, "mmc1-output", "mmc1",
0x08c, 8, 3, 0);
/* TODO Support MMC2 clock's new timing mode. */
static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mod0_default_parents,
0x090,
0, 4, /* M */
16, 2, /* P */
24, 2, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_PHASE(mmc2_sample_clk, "mmc2-sample", "mmc2",
0x090, 20, 3, 0);
static SUNXI_CCU_PHASE(mmc2_output_clk, "mmc2-output", "mmc2",
0x090, 8, 3, 0);
static SUNXI_CCU_MP_WITH_MUX_GATE(ss_clk, "ss", mod0_default_parents,
0x09c,
0, 4, /* M */
16, 2, /* P */
24, 2, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", mod0_default_parents,
0x0a0,
0, 4, /* M */
16, 2, /* P */
24, 4, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_default_parents,
0x0a4,
0, 4, /* M */
16, 2, /* P */
24, 4, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_M_WITH_GATE(i2s0_clk, "i2s0", "pll-audio",
0x0b0, 0, 4, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_M_WITH_GATE(i2s1_clk, "i2s1", "pll-audio",
0x0b4, 0, 4, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_M_WITH_GATE(i2s2_clk, "i2s2", "pll-audio",
0x0b8, 0, 4, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_M_WITH_GATE(tdm_clk, "tdm", "pll-audio",
0x0bc, 0, 4, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_M_WITH_GATE(spdif_clk, "spdif", "pll-audio",
0x0c0, 0, 4, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M",
0x0cc, BIT(8), 0);
static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M",
0x0cc, BIT(9), 0);
static SUNXI_CCU_GATE(usb_hsic_clk, "usb-hsic", "pll-hsic",
0x0cc, BIT(10), 0);
static struct ccu_gate usb_hsic_12m_clk = {
.enable = BIT(11),
.common = {
.reg = 0x0cc,
.prediv = 2,
.features = CCU_FEATURE_ALL_PREDIV,
.hw.init = CLK_HW_INIT("usb-hsic-12m", "osc24M",
&ccu_gate_ops, 0),
}
};
static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc24M",
0x0cc, BIT(16), 0);
/* TODO divider has minimum of 2 */
static SUNXI_CCU_M(dram_clk, "dram", "pll-ddr", 0x0f4, 0, 4, CLK_IS_CRITICAL);
static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram",
0x100, BIT(0), 0);
static SUNXI_CCU_GATE(dram_csi_clk, "dram-csi", "dram",
0x100, BIT(1), 0);
static const char * const tcon0_parents[] = { "pll-video0" };
static SUNXI_CCU_MUX_WITH_GATE(tcon0_clk, "tcon0", tcon0_parents,
0x118, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
static const char * const tcon1_parents[] = { "pll-video1" };
static SUNXI_CCU_MUX_WITH_GATE(tcon1_clk, "tcon1", tcon1_parents,
0x11c, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_GATE(csi_misc_clk, "csi-misc", "osc24M", 0x130, BIT(16), 0);
static SUNXI_CCU_GATE(mipi_csi_clk, "mipi-csi", "osc24M", 0x130, BIT(31), 0);
static const char * const csi_mclk_parents[] = { "pll-de", "osc24M" };
static const u8 csi_mclk_table[] = { 3, 5 };
static SUNXI_CCU_M_WITH_MUX_TABLE_GATE(csi_mclk_clk, "csi-mclk",
csi_mclk_parents, csi_mclk_table,
0x134,
0, 5, /* M */
10, 3, /* mux */
BIT(15), /* gate */
0);
static const char * const csi_sclk_parents[] = { "pll-periph", "pll-ve" };
static const u8 csi_sclk_table[] = { 0, 5 };
static SUNXI_CCU_M_WITH_MUX_TABLE_GATE(csi_sclk_clk, "csi-sclk",
csi_sclk_parents, csi_sclk_table,
0x134,
16, 4, /* M */
24, 3, /* mux */
BIT(31), /* gate */
0);
static SUNXI_CCU_M_WITH_GATE(ve_clk, "ve", "pll-ve", 0x13c,
16, 3, BIT(31), CLK_SET_RATE_PARENT);
static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M", 0x144, BIT(31), 0);
static const char * const hdmi_parents[] = { "pll-video1" };
static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents,
0x150,
0, 4, /* M */
24, 2, /* mux */
BIT(31), /* gate */
CLK_SET_RATE_PARENT);
static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M", 0x154, BIT(31), 0);
static const char * const mbus_parents[] = { "osc24M", "pll-periph",
"pll-ddr" };
static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
0x15c,
0, 3, /* M */
24, 2, /* mux */
BIT(31), /* gate */
CLK_IS_CRITICAL);
static const char * const mipi_dsi0_parents[] = { "pll-video0" };
static const u8 mipi_dsi0_table[] = { 8 };
static SUNXI_CCU_M_WITH_MUX_TABLE_GATE(mipi_dsi0_clk, "mipi-dsi0",
mipi_dsi0_parents, mipi_dsi0_table,
0x168,
0, 4, /* M */
24, 4, /* mux */
BIT(31), /* gate */
CLK_SET_RATE_PARENT);
static const char * const mipi_dsi1_parents[] = { "osc24M", "pll-video0" };
static const u8 mipi_dsi1_table[] = { 0, 9 };
static SUNXI_CCU_M_WITH_MUX_TABLE_GATE(mipi_dsi1_clk, "mipi-dsi1",
mipi_dsi1_parents, mipi_dsi1_table,
0x16c,
0, 4, /* M */
24, 4, /* mux */
BIT(31), /* gate */
CLK_SET_RATE_PARENT);
static SUNXI_CCU_M_WITH_GATE(gpu_core_clk, "gpu-core", "pll-gpu", 0x1a0,
0, 3, BIT(31), CLK_SET_RATE_PARENT);
static const char * const gpu_memory_parents[] = { "pll-gpu", "pll-ddr" };
static SUNXI_CCU_M_WITH_MUX_GATE(gpu_memory_clk, "gpu-memory",
gpu_memory_parents,
0x1a4,
0, 3, /* M */
24, 1, /* mux */
BIT(31), /* gate */
CLK_SET_RATE_PARENT);
static SUNXI_CCU_M_WITH_GATE(gpu_hyd_clk, "gpu-hyd", "pll-gpu", 0x1a8,
0, 3, BIT(31), CLK_SET_RATE_PARENT);
static struct ccu_common *sun8i_a83t_ccu_clks[] = {
&pll_c0cpux_clk.common,
&pll_c1cpux_clk.common,
&pll_audio_clk.common,
&pll_video0_clk.common,
&pll_ve_clk.common,
&pll_ddr_clk.common,
&pll_periph_clk.common,
&pll_gpu_clk.common,
&pll_hsic_clk.common,
&pll_de_clk.common,
&pll_video1_clk.common,
&c0cpux_clk.common,
&c1cpux_clk.common,
&axi0_clk.common,
&axi1_clk.common,
&ahb1_clk.common,
&ahb2_clk.common,
&apb1_clk.common,
&apb2_clk.common,
&bus_mipi_dsi_clk.common,
&bus_ss_clk.common,
&bus_dma_clk.common,
&bus_mmc0_clk.common,
&bus_mmc1_clk.common,
&bus_mmc2_clk.common,
&bus_nand_clk.common,
&bus_dram_clk.common,
&bus_emac_clk.common,
&bus_hstimer_clk.common,
&bus_spi0_clk.common,
&bus_spi1_clk.common,
&bus_otg_clk.common,
&bus_ehci0_clk.common,
&bus_ehci1_clk.common,
&bus_ohci0_clk.common,
&bus_ve_clk.common,
&bus_tcon0_clk.common,
&bus_tcon1_clk.common,
&bus_csi_clk.common,
&bus_hdmi_clk.common,
&bus_de_clk.common,
&bus_gpu_clk.common,
&bus_msgbox_clk.common,
&bus_spinlock_clk.common,
&bus_spdif_clk.common,
&bus_pio_clk.common,
&bus_i2s0_clk.common,
&bus_i2s1_clk.common,
&bus_i2s2_clk.common,
&bus_tdm_clk.common,
&bus_i2c0_clk.common,
&bus_i2c1_clk.common,
&bus_i2c2_clk.common,
&bus_uart0_clk.common,
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
&bus_uart4_clk.common,
&cci400_clk.common,
&nand_clk.common,
&mmc0_clk.common,
&mmc0_sample_clk.common,
&mmc0_output_clk.common,
&mmc1_clk.common,
&mmc1_sample_clk.common,
&mmc1_output_clk.common,
&mmc2_clk.common,
&mmc2_sample_clk.common,
&mmc2_output_clk.common,
&ss_clk.common,
&spi0_clk.common,
&spi1_clk.common,
&i2s0_clk.common,
&i2s1_clk.common,
&i2s2_clk.common,
&tdm_clk.common,
&spdif_clk.common,
&usb_phy0_clk.common,
&usb_phy1_clk.common,
&usb_hsic_clk.common,
&usb_hsic_12m_clk.common,
&usb_ohci0_clk.common,
&dram_clk.common,
&dram_ve_clk.common,
&dram_csi_clk.common,
&tcon0_clk.common,
&tcon1_clk.common,
&csi_misc_clk.common,
&mipi_csi_clk.common,
&csi_mclk_clk.common,
&csi_sclk_clk.common,
&ve_clk.common,
&avs_clk.common,
&hdmi_clk.common,
&hdmi_slow_clk.common,
&mbus_clk.common,
&mipi_dsi0_clk.common,
&mipi_dsi1_clk.common,
&gpu_core_clk.common,
&gpu_memory_clk.common,
&gpu_hyd_clk.common,
};
static struct clk_hw_onecell_data sun8i_a83t_hw_clks = {
.hws = {
[CLK_PLL_C0CPUX] = &pll_c0cpux_clk.common.hw,
[CLK_PLL_C1CPUX] = &pll_c1cpux_clk.common.hw,
[CLK_PLL_AUDIO] = &pll_audio_clk.common.hw,
[CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
[CLK_PLL_VE] = &pll_ve_clk.common.hw,
[CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
[CLK_PLL_PERIPH] = &pll_periph_clk.common.hw,
[CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
[CLK_PLL_HSIC] = &pll_hsic_clk.common.hw,
[CLK_PLL_DE] = &pll_de_clk.common.hw,
[CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
[CLK_C0CPUX] = &c0cpux_clk.common.hw,
[CLK_C1CPUX] = &c1cpux_clk.common.hw,
[CLK_AXI0] = &axi0_clk.common.hw,
[CLK_AXI1] = &axi1_clk.common.hw,
[CLK_AHB1] = &ahb1_clk.common.hw,
[CLK_AHB2] = &ahb2_clk.common.hw,
[CLK_APB1] = &apb1_clk.common.hw,
[CLK_APB2] = &apb2_clk.common.hw,
[CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
[CLK_BUS_SS] = &bus_ss_clk.common.hw,
[CLK_BUS_DMA] = &bus_dma_clk.common.hw,
[CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
[CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
[CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
[CLK_BUS_NAND] = &bus_nand_clk.common.hw,
[CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
[CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
[CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
[CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
[CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
[CLK_BUS_OTG] = &bus_otg_clk.common.hw,
[CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
[CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
[CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
[CLK_BUS_VE] = &bus_ve_clk.common.hw,
[CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
[CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
[CLK_BUS_CSI] = &bus_csi_clk.common.hw,
[CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
[CLK_BUS_DE] = &bus_de_clk.common.hw,
[CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
[CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
[CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
[CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
[CLK_BUS_PIO] = &bus_pio_clk.common.hw,
[CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
[CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
[CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
[CLK_BUS_TDM] = &bus_tdm_clk.common.hw,
[CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
[CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
[CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
[CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
[CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
[CLK_CCI400] = &cci400_clk.common.hw,
[CLK_NAND] = &nand_clk.common.hw,
[CLK_MMC0] = &mmc0_clk.common.hw,
[CLK_MMC0_SAMPLE] = &mmc0_sample_clk.common.hw,
[CLK_MMC0_OUTPUT] = &mmc0_output_clk.common.hw,
[CLK_MMC1] = &mmc1_clk.common.hw,
[CLK_MMC1_SAMPLE] = &mmc1_sample_clk.common.hw,
[CLK_MMC1_OUTPUT] = &mmc1_output_clk.common.hw,
[CLK_MMC2] = &mmc2_clk.common.hw,
[CLK_MMC2_SAMPLE] = &mmc2_sample_clk.common.hw,
[CLK_MMC2_OUTPUT] = &mmc2_output_clk.common.hw,
[CLK_SS] = &ss_clk.common.hw,
[CLK_SPI0] = &spi0_clk.common.hw,
[CLK_SPI1] = &spi1_clk.common.hw,
[CLK_I2S0] = &i2s0_clk.common.hw,
[CLK_I2S1] = &i2s1_clk.common.hw,
[CLK_I2S2] = &i2s2_clk.common.hw,
[CLK_TDM] = &tdm_clk.common.hw,
[CLK_SPDIF] = &spdif_clk.common.hw,
[CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
[CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
[CLK_USB_HSIC] = &usb_hsic_clk.common.hw,
[CLK_USB_HSIC_12M] = &usb_hsic_12m_clk.common.hw,
[CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
[CLK_DRAM] = &dram_clk.common.hw,
[CLK_DRAM_VE] = &dram_ve_clk.common.hw,
[CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
[CLK_TCON0] = &tcon0_clk.common.hw,
[CLK_TCON1] = &tcon1_clk.common.hw,
[CLK_CSI_MISC] = &csi_misc_clk.common.hw,
[CLK_MIPI_CSI] = &mipi_csi_clk.common.hw,
[CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
[CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
[CLK_VE] = &ve_clk.common.hw,
[CLK_AVS] = &avs_clk.common.hw,
[CLK_HDMI] = &hdmi_clk.common.hw,
[CLK_HDMI_SLOW] = &hdmi_slow_clk.common.hw,
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_MIPI_DSI0] = &mipi_dsi0_clk.common.hw,
[CLK_MIPI_DSI1] = &mipi_dsi1_clk.common.hw,
[CLK_GPU_CORE] = &gpu_core_clk.common.hw,
[CLK_GPU_MEMORY] = &gpu_memory_clk.common.hw,
[CLK_GPU_HYD] = &gpu_hyd_clk.common.hw,
},
.num = CLK_NUMBER,
};
static struct ccu_reset_map sun8i_a83t_ccu_resets[] = {
[RST_USB_PHY0] = { 0x0cc, BIT(0) },
[RST_USB_PHY1] = { 0x0cc, BIT(1) },
[RST_USB_HSIC] = { 0x0cc, BIT(2) },
[RST_DRAM] = { 0x0f4, BIT(31) },
[RST_MBUS] = { 0x0fc, BIT(31) },
[RST_BUS_MIPI_DSI] = { 0x2c0, BIT(1) },
[RST_BUS_SS] = { 0x2c0, BIT(5) },
[RST_BUS_DMA] = { 0x2c0, BIT(6) },
[RST_BUS_MMC0] = { 0x2c0, BIT(8) },
[RST_BUS_MMC1] = { 0x2c0, BIT(9) },
[RST_BUS_MMC2] = { 0x2c0, BIT(10) },
[RST_BUS_NAND] = { 0x2c0, BIT(13) },
[RST_BUS_DRAM] = { 0x2c0, BIT(14) },
[RST_BUS_EMAC] = { 0x2c0, BIT(17) },
[RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
[RST_BUS_SPI0] = { 0x2c0, BIT(20) },
[RST_BUS_SPI1] = { 0x2c0, BIT(21) },
[RST_BUS_OTG] = { 0x2c0, BIT(24) },
[RST_BUS_EHCI0] = { 0x2c0, BIT(26) },
[RST_BUS_EHCI1] = { 0x2c0, BIT(27) },
[RST_BUS_OHCI0] = { 0x2c0, BIT(29) },
[RST_BUS_VE] = { 0x2c4, BIT(0) },
[RST_BUS_TCON0] = { 0x2c4, BIT(4) },
[RST_BUS_TCON1] = { 0x2c4, BIT(5) },
[RST_BUS_CSI] = { 0x2c4, BIT(8) },
[RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
[RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
[RST_BUS_DE] = { 0x2c4, BIT(12) },
[RST_BUS_GPU] = { 0x2c4, BIT(20) },
[RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
[RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
[RST_BUS_LVDS] = { 0x2c8, BIT(0) },
[RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
[RST_BUS_I2S0] = { 0x2d0, BIT(12) },
[RST_BUS_I2S1] = { 0x2d0, BIT(13) },
[RST_BUS_I2S2] = { 0x2d0, BIT(14) },
[RST_BUS_TDM] = { 0x2d0, BIT(15) },
[RST_BUS_I2C0] = { 0x2d8, BIT(0) },
[RST_BUS_I2C1] = { 0x2d8, BIT(1) },
[RST_BUS_I2C2] = { 0x2d8, BIT(2) },
[RST_BUS_UART0] = { 0x2d8, BIT(16) },
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
[RST_BUS_UART4] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_a83t_ccu_desc = {
.ccu_clks = sun8i_a83t_ccu_clks,
.num_ccu_clks = ARRAY_SIZE(sun8i_a83t_ccu_clks),
.hw_clks = &sun8i_a83t_hw_clks,
.resets = sun8i_a83t_ccu_resets,
.num_resets = ARRAY_SIZE(sun8i_a83t_ccu_resets),
};
#define SUN8I_A83T_PLL_P_SHIFT 16
#define SUN8I_A83T_PLL_N_SHIFT 8
#define SUN8I_A83T_PLL_N_WIDTH 8
static void sun8i_a83t_cpu_pll_fixup(void __iomem *reg)
{
u32 val = readl(reg);
/* bail out if P divider is not used */
if (!(val & BIT(SUN8I_A83T_PLL_P_SHIFT)))
return;
/*
* If P is used, output should be less than 288 MHz. When we
* set P to 1, we should also decrease the multiplier so the
* output doesn't go out of range, but not too much such that
* the multiplier stays above 12, the minimal operation value.
*
* To keep it simple, set the multiplier to 17, the reset value.
*/
val &= ~GENMASK(SUN8I_A83T_PLL_N_SHIFT + SUN8I_A83T_PLL_N_WIDTH - 1,
SUN8I_A83T_PLL_N_SHIFT);
val |= 17 << SUN8I_A83T_PLL_N_SHIFT;
/* And clear P */
val &= ~BIT(SUN8I_A83T_PLL_P_SHIFT);
writel(val, reg);
}
static int sun8i_a83t_ccu_probe(struct platform_device *pdev)
{
struct resource *res;
void __iomem *reg;
u32 val;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
reg = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(reg))
return PTR_ERR(reg);
/* Enforce d1 = 0, d2 = 0 for Audio PLL */
val = readl(reg + SUN8I_A83T_PLL_AUDIO_REG);
val &= ~(BIT(16) | BIT(18));
writel(val, reg + SUN8I_A83T_PLL_AUDIO_REG);
/* Enforce P = 1 for both CPU cluster PLLs */
sun8i_a83t_cpu_pll_fixup(reg + SUN8I_A83T_PLL_C0CPUX_REG);
sun8i_a83t_cpu_pll_fixup(reg + SUN8I_A83T_PLL_C1CPUX_REG);
return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun8i_a83t_ccu_desc);
}
static const struct of_device_id sun8i_a83t_ccu_ids[] = {
{ .compatible = "allwinner,sun8i-a83t-ccu" },
{ }
};
static struct platform_driver sun8i_a83t_ccu_driver = {
.probe = sun8i_a83t_ccu_probe,
.driver = {
.name = "sun8i-a83t-ccu",
.of_match_table = sun8i_a83t_ccu_ids,
},
};
builtin_platform_driver(sun8i_a83t_ccu_driver);

View File

@ -0,0 +1,64 @@
/*
* Copyright 2016 Chen-Yu Tsai
*
* Chen-Yu Tsai <wens@csie.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef _CCU_SUN8I_A83T_H_
#define _CCU_SUN8I_A83T_H_
#include <dt-bindings/clock/sun8i-a83t-ccu.h>
#include <dt-bindings/reset/sun8i-a83t-ccu.h>
#define CLK_PLL_C0CPUX 0
#define CLK_PLL_C1CPUX 1
#define CLK_PLL_AUDIO 2
#define CLK_PLL_VIDEO0 3
#define CLK_PLL_VE 4
#define CLK_PLL_DDR 5
/* pll-periph is exported to the PRCM block */
#define CLK_PLL_GPU 7
#define CLK_PLL_HSIC 8
/* pll-de is exported for the display engine */
#define CLK_PLL_VIDEO1 10
/* The CPUX clocks are exported */
#define CLK_AXI0 13
#define CLK_AXI1 14
#define CLK_AHB1 15
#define CLK_AHB2 16
#define CLK_APB1 17
#define CLK_APB2 18
/* bus gates exported */
#define CLK_CCI400 58
/* module and usb clocks exported */
#define CLK_DRAM 82
/* dram gates and more module clocks exported */
#define CLK_MBUS 95
/* more module clocks exported */
#define CLK_NUMBER (CLK_GPU_HYD + 1)
#endif /* _CCU_SUN8I_A83T_H_ */

View File

@ -0,0 +1,140 @@
/*
* Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#ifndef _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_
#define _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_
#define CLK_PLL_PERIPH 6
#define CLK_PLL_DE 9
#define CLK_C0CPUX 11
#define CLK_C1CPUX 12
#define CLK_BUS_MIPI_DSI 19
#define CLK_BUS_SS 20
#define CLK_BUS_DMA 21
#define CLK_BUS_MMC0 22
#define CLK_BUS_MMC1 23
#define CLK_BUS_MMC2 24
#define CLK_BUS_NAND 25
#define CLK_BUS_DRAM 26
#define CLK_BUS_EMAC 27
#define CLK_BUS_HSTIMER 28
#define CLK_BUS_SPI0 29
#define CLK_BUS_SPI1 30
#define CLK_BUS_OTG 31
#define CLK_BUS_EHCI0 32
#define CLK_BUS_EHCI1 33
#define CLK_BUS_OHCI0 34
#define CLK_BUS_VE 35
#define CLK_BUS_TCON0 36
#define CLK_BUS_TCON1 37
#define CLK_BUS_CSI 38
#define CLK_BUS_HDMI 39
#define CLK_BUS_DE 40
#define CLK_BUS_GPU 41
#define CLK_BUS_MSGBOX 42
#define CLK_BUS_SPINLOCK 43
#define CLK_BUS_SPDIF 44
#define CLK_BUS_PIO 45
#define CLK_BUS_I2S0 46
#define CLK_BUS_I2S1 47
#define CLK_BUS_I2S2 48
#define CLK_BUS_TDM 49
#define CLK_BUS_I2C0 50
#define CLK_BUS_I2C1 51
#define CLK_BUS_I2C2 52
#define CLK_BUS_UART0 53
#define CLK_BUS_UART1 54
#define CLK_BUS_UART2 55
#define CLK_BUS_UART3 56
#define CLK_BUS_UART4 57
#define CLK_NAND 59
#define CLK_MMC0 60
#define CLK_MMC0_SAMPLE 61
#define CLK_MMC0_OUTPUT 62
#define CLK_MMC1 63
#define CLK_MMC1_SAMPLE 64
#define CLK_MMC1_OUTPUT 65
#define CLK_MMC2 66
#define CLK_MMC2_SAMPLE 67
#define CLK_MMC2_OUTPUT 68
#define CLK_SS 69
#define CLK_SPI0 70
#define CLK_SPI1 71
#define CLK_I2S0 72
#define CLK_I2S1 73
#define CLK_I2S2 74
#define CLK_TDM 75
#define CLK_SPDIF 76
#define CLK_USB_PHY0 77
#define CLK_USB_PHY1 78
#define CLK_USB_HSIC 79
#define CLK_USB_HSIC_12M 80
#define CLK_USB_OHCI0 81
#define CLK_DRAM_VE 83
#define CLK_DRAM_CSI 84
#define CLK_TCON0 85
#define CLK_TCON1 86
#define CLK_CSI_MISC 87
#define CLK_MIPI_CSI 88
#define CLK_CSI_MCLK 89
#define CLK_CSI_SCLK 90
#define CLK_VE 91
#define CLK_AVS 92
#define CLK_HDMI 93
#define CLK_HDMI_SLOW 94
#define CLK_MIPI_DSI0 96
#define CLK_MIPI_DSI1 97
#define CLK_GPU_CORE 98
#define CLK_GPU_MEMORY 99
#define CLK_GPU_HYD 100
#endif /* _DT_BINDINGS_CLOCK_SUN8I_A83T_CCU_H_ */

View File

@ -0,0 +1,98 @@
/*
* Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#ifndef _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_
#define _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_
#define RST_USB_PHY0 0
#define RST_USB_PHY1 1
#define RST_USB_HSIC 2
#define RST_DRAM 3
#define RST_MBUS 4
#define RST_BUS_MIPI_DSI 5
#define RST_BUS_SS 6
#define RST_BUS_DMA 7
#define RST_BUS_MMC0 8
#define RST_BUS_MMC1 9
#define RST_BUS_MMC2 10
#define RST_BUS_NAND 11
#define RST_BUS_DRAM 12
#define RST_BUS_EMAC 13
#define RST_BUS_HSTIMER 14
#define RST_BUS_SPI0 15
#define RST_BUS_SPI1 16
#define RST_BUS_OTG 17
#define RST_BUS_EHCI0 18
#define RST_BUS_EHCI1 19
#define RST_BUS_OHCI0 20
#define RST_BUS_VE 21
#define RST_BUS_TCON0 22
#define RST_BUS_TCON1 23
#define RST_BUS_CSI 24
#define RST_BUS_HDMI0 25
#define RST_BUS_HDMI1 26
#define RST_BUS_DE 27
#define RST_BUS_GPU 28
#define RST_BUS_MSGBOX 29
#define RST_BUS_SPINLOCK 30
#define RST_BUS_LVDS 31
#define RST_BUS_SPDIF 32
#define RST_BUS_I2S0 33
#define RST_BUS_I2S1 34
#define RST_BUS_I2S2 35
#define RST_BUS_TDM 36
#define RST_BUS_I2C0 37
#define RST_BUS_I2C1 38
#define RST_BUS_I2C2 39
#define RST_BUS_UART0 40
#define RST_BUS_UART1 41
#define RST_BUS_UART2 42
#define RST_BUS_UART3 43
#define RST_BUS_UART4 44
#endif /* _DT_BINDINGS_RESET_SUN8I_A83T_CCU_H_ */