hollalinux
/
linux-sg2042
mirror of https://github.com/sophgo/linux-riscv.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
linux-sg2042/drivers/bluetooth/Kconfig

358 lines
10 KiB
Plaintext
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
menu "Bluetooth device drivers"
depends on BT
Bluetooth: btintel: Introduce generic Intel Bluetooth support The majority of Intel Bluetooth vendor commands are shared between USB and UART transports. This creates a separate module that eventually will hold all Intel specific commands, but for now just start with the commands to change the Bluetooth public address and check for the default address. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 15:52:11 +08:00
config BT_INTEL
tristate
Bluetooth: btintel: Add iBT register access over HCI support Add regmap ibt to support Intel Bluetooth silicon register access over HCI. Intel BT/FM combo chip allows to read/write some registers (e.g. FM registers) via its HCI interface. Read/Write operations are performed via a HCI transaction composed of a HCI command (host->controller) followed by a HCI command complete event (controller->host). Read/Write Command opcodes can be specified to the regmap init function. We define data formats which are intel/vendor specific. Register Read/Write HCI command payload (Host): Field: | REG ADDR | MODE | DATA_LEN | DATA... | size: | 32b | 8b | 8b | 8b* | Register Read HCI command complete event payload (Controller): Field: | CMD STATUS | REG ADDR | DATA... | size: | 8b | 32b | 8b* | Register Write HCI command complete event payload (Controller): Field: | CMD_STATUS | size: | 8b | Since this payload is HCI encapsulated, Little Endian byte order is used. Write/Read Example: If we write 0x0000002a at address 0x00008c04, with opcode_write 0xfc5d, The resulting transaction is (btmon trace): < HCI Command (0x3f|0x005d) plen 10 [hci0] 04 8c 00 00 02 04 2a 00 00 00 > HCI Event (0x0e) plen 4 Unknown (0x3f|0x005d) ncmd 1 00 Then, if we read the same register with opcode_read 0xfc5e: < HCI Command (0x3f|0x005e) plen 6 [hci0] 04 8c 00 00 02 04 > HCI Event (0x0e) plen 12 [hci0] Unknown (0x3f|0x005e) ncmd 1 00 04 8c 00 00 2a 00 00 00 Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-02 00:16:21 +08:00
select REGMAP
Bluetooth: btintel: Introduce generic Intel Bluetooth support The majority of Intel Bluetooth vendor commands are shared between USB and UART transports. This creates a separate module that eventually will hold all Intel specific commands, but for now just start with the commands to change the Bluetooth public address and check for the default address. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 15:52:11 +08:00
Bluetooth: btbcm: Introduce generic Broadcom Bluetooth support The majority of Broadcom Bluetooth vendor commands are shared between USB and UART transports. This creates a separate module that eventually will hold all Broadcom specific commands, but for now just start with the commands to change the Bluetooth public address and check for the default address. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 13:52:10 +08:00
config BT_BCM
tristate
Bluetooth: btbcm: Add support for Broadcom controller setup To unify the controller setup of Broadcom devices between USB and UART transport, add the patchram download support into the Broadcom module. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 13:52:13 +08:00
select FW_LOADER
Bluetooth: btbcm: Introduce generic Broadcom Bluetooth support The majority of Broadcom Bluetooth vendor commands are shared between USB and UART transports. This creates a separate module that eventually will hold all Broadcom specific commands, but for now just start with the commands to change the Bluetooth public address and check for the default address. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 13:52:10 +08:00
Bluetooth: btrtl: Create separate module for Realtek BT driver As already done for btintel and btbcm export setup as separate function in a vendor-specific module to hold all the Realtek specific commands. Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-14 16:49:09 +08:00
config BT_RTL
tristate
select FW_LOADER
Bluetooth: btqca: Introduce generic QCA ROME support This is for supporting BT for QCA ROME with vendor specific HCI commands and initialization on the chip. This will have USB/UART implementation both, but for now, adding UART vendor specific commands to patch downloading and set Bluetooth device address using vendor specific command. Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-11 05:24:12 +08:00
config BT_QCA
tristate
select FW_LOADER
[Bluetooth] Add generic driver for Bluetooth USB devices This patch adds a new generic driver for Bluetooth USB devices. This driver is still experimental at this point, but it is cleaner and easier to maintain than the current Bluetooth USB driver. It is a much better starting point for power management improvements. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-20 20:12:34 +08:00
config BT_HCIBTUSB
[Bluetooth] Add SCO support to btusb driver The new generic driver for Bluetooth USB devices was missing proper SCO support. The driver now claims the second interface for these USB devices to allow the flow of SCO packets. It also handles switching of the alternate setting and re-submission of isochronous URBs. The btusb driver is now a full replacement for hci_usb and thus the experimental tag has been removed and this driver is promoted as preferred one. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-18 19:23:52 +08:00
tristate "HCI USB driver"
depends on USB
Bluetooth: btusb: Use generic Intel support for address support The Bluetooth address handling for Intel devices is provided by a generic module now. Start using that module instead of relying it being included in the driver. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 15:52:12 +08:00
select BT_INTEL
[Bluetooth] Add generic driver for Bluetooth USB devices This patch adds a new generic driver for Bluetooth USB devices. This driver is still experimental at this point, but it is cleaner and easier to maintain than the current Bluetooth USB driver. It is a much better starting point for power management improvements. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-20 20:12:34 +08:00
help
Bluetooth HCI USB driver.
This driver is required if you want to use Bluetooth devices with
USB interface.
Say Y here to compile support for Bluetooth USB devices into the
kernel or say M to compile it as module (btusb).
Bluetooth: btusb: Add option for Broadcom protocol support With the generic Broadcom Bluetooth support module, it is possible to turn support for firmware and patchram download into an optional feature. To keep backwards compatibility with previous kernel configurations, the new option defaults to enabled. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 13:52:14 +08:00
config BT_HCIBTUSB_BCM
bool "Broadcom protocol support"
depends on BT_HCIBTUSB
select BT_BCM
default y
help
The Broadcom protocol support enables firmware and patchram
download support for Broadcom Bluetooth controllers.
Say Y here to compile support for Broadcom protocol.
Bluetooth: btrtl: Create separate module for Realtek BT driver As already done for btintel and btbcm export setup as separate function in a vendor-specific module to hold all the Realtek specific commands. Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-05-14 16:49:09 +08:00
config BT_HCIBTUSB_RTL
bool "Realtek protocol support"
depends on BT_HCIBTUSB
select BT_RTL
default y
help
The Realtek protocol support enables firmware and configuration
download support for Realtek Bluetooth controllers.
Say Y here to compile support for Realtek protocol.
[Bluetooth] Add generic driver for Bluetooth SDIO devices This patch adds a generic driver for Bluetooth SDIO devices. It supports Type-A and Type-B devices. Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-20 20:02:04 +08:00
config BT_HCIBTSDIO
tristate "HCI SDIO driver"
depends on MMC
help
Bluetooth HCI SDIO driver.
This driver is required if you want to use Bluetooth device with
SDIO interface.
Say Y here to compile support for Bluetooth SDIO devices into the
kernel or say M to compile it as module (btsdio).
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
config BT_HCIUART
tristate "HCI UART driver"
tty: Added a CONFIG_TTY option to allow removal of TTY The option allows you to remove TTY and compile without errors. This saves space on systems that won't support TTY interfaces anyway. bloat-o-meter output is below. The bulk of this patch consists of Kconfig changes adding "depends on TTY" to various serial devices and similar drivers that require the TTY layer. Ideally, these dependencies would occur on a common intermediate symbol such as SERIO, but most drivers "select SERIO" rather than "depends on SERIO", and "select" does not respect dependencies. bloat-o-meter output comparing our previous minimal to new minimal by removing TTY. The list is filtered to not show removed entries with awk '$3 != "-"' as the list was very long. add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350) function old new delta chr_dev_init 166 170 +4 allow_signal 80 82 +2 static.__warned 143 142 -1 disallow_signal 63 62 -1 __set_special_pids 95 94 -1 unregister_console 126 121 -5 start_kernel 546 541 -5 register_console 593 588 -5 copy_from_user 45 40 -5 sys_setsid 128 120 -8 sys_vhangup 32 19 -13 do_exit 1543 1526 -17 bitmap_zero 60 40 -20 arch_local_irq_save 137 117 -20 release_task 674 652 -22 static.spin_unlock_irqrestore 308 260 -48 Signed-off-by: Joe Millenbach <jmillenbach@gmail.com> Reviewed-by: Jamey Sharp <jamey@minilop.net> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-18 14:44:22 +08:00
depends on TTY
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
help
Bluetooth HCI UART driver.
This driver is required if you want to use Bluetooth devices with
Bluetooth: Remove trailing whitespaces from Kconfig Fixed a coding style issue. Removed trailing whitespaces in drivers/bluetooth/Kconfig. Signed-off-by: Stephan Gabert <stephan.gabert@fau.de> Signed-off-by: Nicolas Pfeiffer <nicolas.pfeiffer@fau.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-06-17 00:52:25 +08:00
serial port interface. You will also need this driver if you have
UART based Bluetooth PCMCIA and CF devices like Xircom Credit Card
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
adapter and BrainBoxes Bluetooth PC Card.
Say Y here to compile support for Bluetooth UART devices into the
kernel or say M to compile it as module (hci_uart).
config BT_HCIUART_H4
bool "UART (H4) protocol support"
depends on BT_HCIUART
help
Bluetooth: Remove trailing whitespaces from Kconfig Fixed a coding style issue. Removed trailing whitespaces in drivers/bluetooth/Kconfig. Signed-off-by: Stephan Gabert <stephan.gabert@fau.de> Signed-off-by: Nicolas Pfeiffer <nicolas.pfeiffer@fau.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-06-17 00:52:25 +08:00
UART (H4) is serial protocol for communication between Bluetooth
device and host. This protocol is required for most Bluetooth devices
with UART interface, including PCMCIA and CF cards.
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
Say Y here to compile support for HCI UART (H4) protocol.
config BT_HCIUART_BCSP
bool "BCSP protocol support"
depends on BT_HCIUART
bluetooth/hci_bcsp: fix bitrev Kconfig Fix bluetooth hci_bcsp Kconfig to avoid build errors: drivers/built-in.o: In function `bcsp_prepare_pkt': hci_bcsp.c:(.text+0x7e9ac): undefined reference to `bitrev16' drivers/built-in.o: In function `bcsp_recv': hci_bcsp.c:(.text+0x7f276): undefined reference to `bitrev16' hci_bcsp.c:(.text+0x7f293): undefined reference to `bitrev16' make[1]: *** [.tmp_vmlinux1] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Ackey-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-15 15:51:45 +08:00
select BITREVERSE
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
help
Bluetooth: Remove trailing whitespaces from Kconfig Fixed a coding style issue. Removed trailing whitespaces in drivers/bluetooth/Kconfig. Signed-off-by: Stephan Gabert <stephan.gabert@fau.de> Signed-off-by: Nicolas Pfeiffer <nicolas.pfeiffer@fau.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-06-17 00:52:25 +08:00
BCSP (BlueCore Serial Protocol) is serial protocol for communication
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
between Bluetooth device and host. This protocol is required for non
USB Bluetooth devices based on CSR BlueCore chip, including PCMCIA and
CF cards.
Say Y here to compile support for HCI BCSP protocol.
Bluetooth: Support for Atheros AR300x serial chip Implements Atheros AR300x serial HCI protocol. This protocol extends H4 serial protocol to implement enhanced power management features supported by Atheros AR300x serial Bluetooth chipsets. Signed-off-by: Suraj Sumangala <suraj@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-19 15:04:07 +08:00
config BT_HCIUART_ATH3K
bool "Atheros AR300x serial support"
depends on BT_HCIUART
Bluetooth: hci_uart: Use h4_recv_buf helper for Atheros AR300x Instead of using hci_recv_stream_fragment, use the local available h4_recv_buf helper function. To ensure that the function is available select BT_HCIUART_H4. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-05 12:59:26 +08:00
select BT_HCIUART_H4
Bluetooth: Support for Atheros AR300x serial chip Implements Atheros AR300x serial HCI protocol. This protocol extends H4 serial protocol to implement enhanced power management features supported by Atheros AR300x serial Bluetooth chipsets. Signed-off-by: Suraj Sumangala <suraj@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-19 15:04:07 +08:00
help
HCIATH3K (HCI Atheros AR300x) is a serial protocol for
communication between host and Atheros AR300x Bluetooth devices.
This protocol enables AR300x chips to be enabled with
power management support.
Enable this if you have Atheros AR300x serial Bluetooth device.
Say Y here to compile support for HCI UART ATH3K protocol.
[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips Add support for Texas Instruments' HCI Low Level (HCILL) Bluetooth protocol, which is a power management extension to H4. The HCILL is widely used by TI's BRF63xx Bluetooth chips. Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2007-10-20 19:42:36 +08:00
config BT_HCIUART_LL
bool "HCILL protocol support"
depends on BT_HCIUART
help
HCILL (HCI Low Level) is a serial protocol for communication
between Bluetooth device and host. This protocol is required for
serial Bluetooth devices that are based on Texas Instruments'
BRF chips.
Say Y here to compile support for HCILL protocol.
Bluetooth: Initial skeleton for Three-wire UART (H5) support This patch adds the initial skeleton for Three-wire UART (H5) support and hooks it up to the HCI UART framework. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-07-16 21:12:02 +08:00
config BT_HCIUART_3WIRE
bool "Three-wire UART (H5) protocol support"
depends on BT_HCIUART
help
The HCI Three-wire UART Transport Layer makes it possible to
user the Bluetooth HCI over a serial port interface. The HCI
Three-wire UART Transport Layer assumes that the UART
communication may have bit errors, overrun errors or burst
errors and thereby making CTS/RTS lines unnecessary.
Say Y here to compile support for Three-wire UART protocol.
Bluetooth: hci_uart: Add support Intel address configuration When using vendor detection, this adds support for the Intel specific address configuration command. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-05 07:13:02 +08:00
config BT_HCIUART_INTEL
bool "Intel protocol support"
depends on BT_HCIUART
Bluetooth: hci_uart: Add basic support for Intel Lightning Peak devices The Intel Lightning Peak devices do not come with Bluetooth firmware loaded and thus require a full download of the operational Bluetooth firmware when the device is attached via the Bluetooth line discipline. Lightning Peak devices start with a bootloader mode that only accepts a very limited set of HCI commands. The supported commands are enough to identify the hardware and select the right firmware to load. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-01 18:20:26 +08:00
select BT_HCIUART_H4
Bluetooth: hci_uart: Use generic Intel support for address setting The Bluetooth address setting for Intel devices is provided by a generic module now. Start using that module instead of relying it being included in the driver. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 15:52:14 +08:00
select BT_INTEL
Bluetooth: hci_uart: Add support Intel address configuration When using vendor detection, this adds support for the Intel specific address configuration command. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-05 07:13:02 +08:00
help
The Intel protocol support enables Bluetooth HCI over serial
port interface for Intel Bluetooth controllers.
Say Y here to compile support for Intel protocol.
Bluetooth: hci_uart: Add support Broadcom address configuration When using vendor detection, this adds support for the Broadcom specific address configuration command. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-05 07:13:03 +08:00
config BT_HCIUART_BCM
bool "Broadcom protocol support"
depends on BT_HCIUART
Bluetooth: hci_uart: Add protocol support for Broadcom UART devices This adds the protocol support for Broadcom based UART devices to enable firmware and patchram download procedure. It is a pretty straight forward H:4 driver with the exception of actually having its own setup and address configuration callbacks. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 13:52:18 +08:00
select BT_HCIUART_H4
Bluetooth: hci_uart: Use generic functionality from Broadcom module The new Broadcom Bluetooth support module provides generic functionality for changing and checking the Bluetooth device address. Use these new features instead of keeping a duplicate in the driver. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-06 13:52:12 +08:00
select BT_BCM
Bluetooth: hci_uart: Add support Broadcom address configuration When using vendor detection, this adds support for the Broadcom specific address configuration command. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-04-05 07:13:03 +08:00
help
The Broadcom protocol support enables Bluetooth HCI over serial
port interface for Broadcom Bluetooth controllers.
Say Y here to compile support for Broadcom protocol.
Bluetooth: hciuart: Add support QCA chipset for UART QCA61x4 chips have supported sleep feature using In-Band-Sleep commands to enable sleep feature based on H4 protocol. After sending patch/nvm configuration is done, IBS mode will be up and running Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-11 05:24:17 +08:00
config BT_HCIUART_QCA
bool "Qualcomm Atheros protocol support"
depends on BT_HCIUART
select BT_HCIUART_H4
select BT_QCA
help
The Qualcomm Atheros protocol supports HCI In-Band Sleep feature
over serial port interface(H4) between controller and host.
This protocol is required for UART clock control for QCA Bluetooth
devices.
Say Y here to compile support for QCA protocol.
Bluetooth: hci_uart: Add Intel/AG6xx support This driver implements support for iBT2.1 Bluetooth controller embedded in the AG620 communication combo. The controller needs to be configured with bddata and can be patched with a binary patch file (pbn). These operations are performed in manufacturing mode. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-02-22 17:48:03 +08:00
config BT_HCIUART_AG6XX
bool "Intel AG6XX protocol support"
depends on BT_HCIUART
select BT_HCIUART_H4
select BT_INTEL
help
The Intel/AG6XX protocol support enables Bluetooth HCI over serial
port interface for Intel ibt 2.1 Bluetooth controllers.
Say Y here to compile support for Intel AG6XX protocol.
Bluetooth: hci_uart: Add Marvell support This patch introduces support for Marvell Bluetooth controller over UART (8897 for now). In order to send the final firmware at full speed, a helper firmware is firstly sent. Firmware download is driven by the controller which sends request firmware packets (including expected size). This driver is a global rework of the one proposed by Amitkumar Karwar <akarwar@marvell.com>. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-09-19 22:29:27 +08:00
config BT_HCIUART_MRVL
bool "Marvell protocol support"
depends on BT_HCIUART
select BT_HCIUART_H4
help
Marvell is serial protocol for communication between Bluetooth
device and host. This protocol is required for most Marvell Bluetooth
devices with UART interface.
Say Y here to compile support for HCI MRVL protocol.
Bluetooth: hci_uart: Add Intel/AG6xx support This driver implements support for iBT2.1 Bluetooth controller embedded in the AG620 communication combo. The controller needs to be configured with bddata and can be patched with a binary patch file (pbn). These operations are performed in manufacturing mode. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-02-22 17:48:03 +08:00
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
config BT_HCIBCM203X
tristate "HCI BCM203x USB driver"
depends on USB
select FW_LOADER
help
Bluetooth HCI BCM203x USB driver.
This driver provides the firmware loading mechanism for the Broadcom
Blutonium based devices.
Say Y here to compile support for HCI BCM203x devices into the
kernel or say M to compile it as module (bcm203x).
config BT_HCIBPA10X
tristate "HCI BPA10x USB driver"
Bluetooth: bpa10x: fix BT_HCIUART dependency The change to bpa10x to use the h4_recv_buf helper added a dependency on BT_HCIUART. This was incorrectly added to Kconfig by adding a 'select' statement, which now in turn causes build failures when CONFIG_TTY is not set: warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY) vers/built-in.o: In function `hci_uart_tty_receive': fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle' drivers/built-in.o: In function `hci_uart_tty_ioctl': fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper' drivers/built-in.o: In function `hci_uart_flush': This replaces the 'select BT_HCIUART' dependency with 'depends on', which does not have this kind of problem. Alternatively, one could add 'depends on TTY', but avoiding 'select' on user-visible options is generally the preferred choice as that does not introduce the potential for dependency loops or incomplete dependency chains. Fixes: 91489919247a ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency") Fixes: 943cc592195e ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-17 06:03:38 +08:00
depends on USB && BT_HCIUART
Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly The manually coded frame reassembly is actually broken. The h4_recv_buf helper from the UART driver is a perfect fit for frame reassembly for this driver. So just export that function and use it here as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08 09:06:53 +08:00
select BT_HCIUART_H4
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
help
Bluetooth HCI BPA10x USB driver.
This driver provides support for the Digianswer BPA 100/105 Bluetooth
sniffer devices.
Say Y here to compile support for HCI BPA10x devices into the
kernel or say M to compile it as module (bpa10x).
config BT_HCIBFUSB
tristate "HCI BlueFRITZ! USB driver"
depends on USB
select FW_LOADER
help
Bluetooth HCI BlueFRITZ! USB driver.
This driver provides support for Bluetooth USB devices with AVM
interface:
AVM BlueFRITZ! USB
Say Y here to compile support for HCI BFUSB devices into the
kernel or say M to compile it as module (bfusb).
config BT_HCIDTL1
tristate "HCI DTL1 (PC Card) driver"
depends on PCMCIA
help
Bluetooth HCI DTL1 (PC Card) driver.
This driver provides support for Bluetooth PCMCIA devices with
Nokia DTL1 interface:
Nokia Bluetooth Card
Socket Bluetooth CF Card
Say Y here to compile support for HCI DTL1 devices into the
kernel or say M to compile it as module (dtl1_cs).
config BT_HCIBT3C
tristate "HCI BT3C (PC Card) driver"
depends on PCMCIA
select FW_LOADER
help
Bluetooth HCI BT3C (PC Card) driver.
This driver provides support for Bluetooth PCMCIA devices with
3Com BT3C interface:
3Com Bluetooth Card (3CRWB6096)
HP Bluetooth Card
Say Y here to compile support for HCI BT3C devices into the
kernel or say M to compile it as module (bt3c_cs).
config BT_HCIBLUECARD
tristate "HCI BlueCard (PC Card) driver"
depends on PCMCIA
help
Bluetooth HCI BlueCard (PC Card) driver.
This driver provides support for Bluetooth PCMCIA devices with
Anycom BlueCard interface:
Anycom Bluetooth PC Card
Anycom Bluetooth CF Card
Say Y here to compile support for HCI BlueCard devices into the
kernel or say M to compile it as module (bluecard_cs).
config BT_HCIBTUART
tristate "HCI UART (PC Card) device driver"
depends on PCMCIA
help
Bluetooth HCI UART (PC Card) driver.
This driver provides support for Bluetooth PCMCIA devices with
an UART interface:
Xircom CreditCard Bluetooth Adapter
Xircom RealPort2 Bluetooth Adapter
Sphinx PICO Card
H-Soft blue+Card
Cyber-blue Compact Flash Card
Say Y here to compile support for HCI UART devices into the
kernel or say M to compile it as module (btuart_cs).
config BT_HCIVHCI
tristate "HCI VHCI (Virtual HCI device) driver"
help
Bluetooth Virtual HCI device driver.
This driver is required if you want to use HCI Emulation software.
Say Y here to compile support for virtual HCI devices into the
kernel or say M to compile it as module (hci_vhci).
Bluetooth: Add btmrvl driver for Marvell Bluetooth devices This driver provides basic definitions and library functions to support Marvell Bluetooth enabled devices, such as 88W8688 WLAN/BT combo chip. This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-03 05:29:35 +08:00
config BT_MRVL
tristate "Marvell Bluetooth driver support"
help
The core driver to support Marvell Bluetooth devices.
This driver is required if you want to support
Bluetooth: btmrvl: add sd8997 chipset support This patch adds support for Marvell's new chipset SD8997. Register offsets and supported feature flags are updated. Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-21 18:06:42 +08:00
Marvell Bluetooth devices, such as 8688/8787/8797/8887/8897/8997.
Bluetooth: Add btmrvl driver for Marvell Bluetooth devices This driver provides basic definitions and library functions to support Marvell Bluetooth enabled devices, such as 88W8688 WLAN/BT combo chip. This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-03 05:29:35 +08:00
Say Y here to compile Marvell Bluetooth driver
into the kernel or say M to compile it as module.
Bluetooth: Add Marvell BT-over-SDIO driver This driver supports Marvell Bluetooth enabled devices with SDIO interface. Currently only SD8688 chip is supported. The helper/firmware images of SD8688 can be downloaded from this tree: git://git.infradead.org/users/dwmw2/linux-firmware.git This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-03 05:29:36 +08:00
config BT_MRVL_SDIO
tristate "Marvell BT-over-SDIO driver"
depends on BT_MRVL && MMC
Bluetooth: Fix Kconfig for Marvell Bluetooth driver The Marvell driver selects DEBUG_FS and FW_LOADER for its core driver and that is pointless. Don't select DEBUG_FS since it is either enabled or not and it is not for the driver to enable it. Also FW_LOADER is only used within the SDIO driver and so just have that one select the FW_LOADER option. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-09 19:42:54 +08:00
select FW_LOADER
Bluetooth: btmrvl add firmware dump support This patch adds firmware dump support for marvell bluetooth chipset. Currently only SD8897 is supported. This is implemented based on dev_coredump, a new mechnism introduced in kernel 3.18rc3 Firmware dump can be trigger by echo 1 > /sys/kernel/debug/bluetooth/hci*/config/fw_dump and when the dump operation is completed, data can be read by cat /sys/class/devcoredump/devcd*/data We have prepared following script to divide fw memory dump data into multiple files based on memory type. [root]# cat btmrvl_split_dump_data.sh #!/bin/bash # usage: ./btmrvl_split_dump_data.sh dump_data fw_dump_data=$1 mem_type="ITCM DTCM SQRAM APU CIU ICU MAC EXT7 EXT8 EXT9 EXT10 EXT11 EXT12 EXT13 EXTLAST" for name in ${mem_type[@]} do sed -n "/Start dump $name/,/End dump/p" $fw_dump_data > tmp.$name.log if [ ! -s tmp.$name.log ] then rm -rf tmp.$name.log else # Remove the describle info "Start dump" and "End dump" sed '1d' tmp.$name.log | sed '$d' > /data/$name.log if [ -s /data/$name.log ] then echo "generate /data/$name.log" else sed '1d' tmp.$name.log | sed '$d' > /var/$name.log echo "generate /var/$name.log" fi rm -rf tmp.$name.log fi done Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-11-24 18:40:53 +08:00
select WANT_DEV_COREDUMP
Bluetooth: Add Marvell BT-over-SDIO driver This driver supports Marvell Bluetooth enabled devices with SDIO interface. Currently only SD8688 chip is supported. The helper/firmware images of SD8688 can be downloaded from this tree: git://git.infradead.org/users/dwmw2/linux-firmware.git This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-03 05:29:36 +08:00
help
The driver for Marvell Bluetooth chipsets with SDIO interface.
This driver is required if you want to use Marvell Bluetooth
Bluetooth: btmrvl: add sd8997 chipset support This patch adds support for Marvell's new chipset SD8997. Register offsets and supported feature flags are updated. Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-21 18:06:42 +08:00
devices with SDIO interface. Currently SD8688/SD8787/SD8797/SD8887/SD8897/SD8997
Bluetooth: btmrvl: support Marvell Bluetooth device SD8797 The SD8797 firmware image is shared with mwifiex driver. Whoever gets loaded first will be responsible for firmware downloading. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Frank Huang <frankh@marvell.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-11-17 12:40:42 +08:00
chipsets are supported.
Bluetooth: Add Marvell BT-over-SDIO driver This driver supports Marvell Bluetooth enabled devices with SDIO interface. Currently only SD8688 chip is supported. The helper/firmware images of SD8688 can be downloaded from this tree: git://git.infradead.org/users/dwmw2/linux-firmware.git This patch incorporates a lot of comments given by Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre. Signed-off-by: Rahul Tank <rahult@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-06-03 05:29:36 +08:00
Say Y here to compile support for Marvell BT-over-SDIO driver
into the kernel or say M to compile it as module.
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011 Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com> Signed-off-by: Alicke Xu <sxu@atheros.com> Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-01-06 21:34:15 +08:00
config BT_ATH3K
tristate "Atheros firmware download driver"
depends on BT_HCIBTUSB
select FW_LOADER
help
Bluetooth firmware download driver.
This driver loads the firmware into the Atheros Bluetooth
chipset.
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011 Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com> Signed-off-by: Alicke Xu <sxu@atheros.com> Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-01-06 21:34:15 +08:00
Say Y here to compile support for "Atheros firmware download driver"
into the kernel or say M to compile it as module (ath3k).
Bluetooth: btwilink driver This is the bluetooth protocol driver for the TI WiLink7 chipsets. Texas Instrument's WiLink chipsets combine wireless technologies like BT, FM, GPS and WLAN onto a single chip. This Bluetooth driver works on top of the TI_ST shared transport line discipline driver which also allows other drivers like FM V4L2 and GPS character driver to make use of the same UART interface. Kconfig and Makefile modifications to enable the Bluetooth driver for Texas Instrument's WiLink 7 chipset. Signed-off-by: Pavan Savoy <pavan_savoy@ti.com> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-21 12:41:16 +08:00
config BT_WILINK
tristate "Texas Instruments WiLink7 driver"
depends on TI_ST
help
This enables the Bluetooth driver for Texas Instrument's BT/FM/GPS
combo devices. This makes use of shared transport line discipline
core driver to communicate with the BT core of the combo chip.
Say Y here to compile support for Texas Instrument's WiLink7 driver
Bluetooth: add module name for btwilink Btwilink help did not include module name, add it. Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-01-17 21:34:30 +08:00
into the kernel or say M to compile it as module (btwilink).
Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver The Qualcomm WCNSS chip provides two SMD channels to the BT core; one for command and one for event packets. This driver exposes the two channels as a hci device. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-08-13 08:01:28 +08:00
config BT_QCOMSMD
tristate "Qualcomm SMD based HCI support"
Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled The driver only has runtime but no build time dependency with QCOM_SMD && QCOM_WCNSS_CTRL. So it can be built for testing purposes if COMPILE_TEST option is enabled. This is useful to have more build coverage and make sure that the driver is not affected by changes that could cause build regressions. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-01-02 21:23:23 +08:00
depends on (QCOM_SMD && QCOM_WCNSS_CTRL) || COMPILE_TEST
Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver The Qualcomm WCNSS chip provides two SMD channels to the BT core; one for command and one for event packets. This driver exposes the two channels as a hci device. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-08-13 08:01:28 +08:00
select BT_QCA
help
Qualcomm SMD based HCI driver.
This driver is used to bridge HCI data onto the shared memory
channels to the WCNSS core.
Say Y here to compile support for HCI over Qualcomm SMD into the
kernel or say M to compile as a module.
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011 Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com> Signed-off-by: Alicke Xu <sxu@atheros.com> Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-01-06 21:34:15 +08:00
endmenu