hollalinux
/
linux-sg2042
mirror of https://github.com/sophgo/linux-riscv.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
linux-sg2042/drivers/usb/common/ulpi.c

322 lines
7.1 KiB
C
Raw Normal View History

USB: add SPDX identifiers to all remaining files in drivers/usb/ It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/usb/ and include/linux/usb* files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-03 18:28:30 +08:00
// SPDX-License-Identifier: GPL-2.0
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
/**
* ulpi.c - USB ULPI PHY bus
*
* Copyright (C) 2015 Intel Corporation
*
* Author: Heikki Krogerus <heikki.krogerus@linux.intel.com>
*/
#include <linux/ulpi/interface.h>
#include <linux/ulpi/driver.h>
#include <linux/ulpi/regs.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/acpi.h>
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/clk/clk-conf.h>
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
/* -------------------------------------------------------------------------- */
int ulpi_read(struct ulpi *ulpi, u8 addr)
{
usb: ulpi: rename operations {read|write}_dev to simply {read|write} With the removal of the old {read|write} operations, we can now safely rename the new api operations {read|write}_dev to use the shorter and clearer names {read|write}, respectively. Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Tal Shorer <tal.shorer@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-17 00:04:50 +08:00
return ulpi->ops->read(ulpi->dev.parent, addr);
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
}
EXPORT_SYMBOL_GPL(ulpi_read);
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
{
usb: ulpi: rename operations {read|write}_dev to simply {read|write} With the removal of the old {read|write} operations, we can now safely rename the new api operations {read|write}_dev to use the shorter and clearer names {read|write}, respectively. Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Tal Shorer <tal.shorer@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-17 00:04:50 +08:00
return ulpi->ops->write(ulpi->dev.parent, addr, val);
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
}
EXPORT_SYMBOL_GPL(ulpi_write);
/* -------------------------------------------------------------------------- */
static int ulpi_match(struct device *dev, struct device_driver *driver)
{
struct ulpi_driver *drv = to_ulpi_driver(driver);
struct ulpi *ulpi = to_ulpi_dev(dev);
const struct ulpi_device_id *id;
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
/* Some ULPI devices don't have a vendor id so rely on OF match */
if (ulpi->id.vendor == 0)
return of_driver_match_device(dev, driver);
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
for (id = drv->id_table; id->vendor; id++)
if (id->vendor == ulpi->id.vendor &&
id->product == ulpi->id.product)
return 1;
return 0;
}
static int ulpi_uevent(struct device *dev, struct kobj_uevent_env *env)
{
struct ulpi *ulpi = to_ulpi_dev(dev);
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
int ret;
ret = of_device_uevent_modalias(dev, env);
if (ret != -ENODEV)
return ret;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
if (add_uevent_var(env, "MODALIAS=ulpi:v%04xp%04x",
ulpi->id.vendor, ulpi->id.product))
return -ENOMEM;
return 0;
}
static int ulpi_probe(struct device *dev)
{
struct ulpi_driver *drv = to_ulpi_driver(dev->driver);
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
int ret;
ret = of_clk_set_defaults(dev->of_node, false);
if (ret < 0)
return ret;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
return drv->probe(to_ulpi_dev(dev));
}
static int ulpi_remove(struct device *dev)
{
struct ulpi_driver *drv = to_ulpi_driver(dev->driver);
if (drv->remove)
drv->remove(to_ulpi_dev(dev));
return 0;
}
static struct bus_type ulpi_bus = {
.name = "ulpi",
.match = ulpi_match,
.uevent = ulpi_uevent,
.probe = ulpi_probe,
.remove = ulpi_remove,
};
/* -------------------------------------------------------------------------- */
static ssize_t modalias_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
int len;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
struct ulpi *ulpi = to_ulpi_dev(dev);
of: Add function for generating a DT modalias with a newline The modalias sysfs attr is lacking a newline for DT aliases on platform devices. The macio and ibmebus correctly add the newline, but open code it. Introduce a new function, of_device_modalias(), that fills the buffer with the modalias including the newline and update users of the old of_device_get_modalias function. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Frank Rowand <frowand.list@gmail.com> Cc: linuxppc-dev@lists.ozlabs.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-22 22:16:27 +08:00
len = of_device_modalias(dev, buf, PAGE_SIZE);
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
if (len != -ENODEV)
return len;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
return sprintf(buf, "ulpi:v%04xp%04x\n",
ulpi->id.vendor, ulpi->id.product);
}
static DEVICE_ATTR_RO(modalias);
static struct attribute *ulpi_dev_attrs[] = {
&dev_attr_modalias.attr,
NULL
};
static struct attribute_group ulpi_dev_attr_group = {
.attrs = ulpi_dev_attrs,
};
static const struct attribute_group *ulpi_dev_attr_groups[] = {
&ulpi_dev_attr_group,
NULL
};
static void ulpi_dev_release(struct device *dev)
{
kfree(to_ulpi_dev(dev));
}
usb: make device_type const Make this const as it is only stored in the type field of a device structure, which is const. Done using Coccinelle. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-19 16:22:26 +08:00
static const struct device_type ulpi_dev_type = {
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
.name = "ulpi_device",
.groups = ulpi_dev_attr_groups,
.release = ulpi_dev_release,
};
/* -------------------------------------------------------------------------- */
/**
* ulpi_register_driver - register a driver with the ULPI bus
* @drv: driver being registered
*
* Registers a driver with the ULPI bus.
*/
usb: ulpi: Automatically set driver::owner with ulpi_driver_register() Let's follow other driver registration functions and automatically set the driver's owner member to THIS_MODULE when ulpi_driver_register() is called. This allows ulpi driver writers to forget about this boiler plate detail and avoids common bugs in the process. Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 13:38:21 +08:00
int __ulpi_register_driver(struct ulpi_driver *drv, struct module *module)
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
{
if (!drv->probe)
return -EINVAL;
usb: ulpi: Automatically set driver::owner with ulpi_driver_register() Let's follow other driver registration functions and automatically set the driver's owner member to THIS_MODULE when ulpi_driver_register() is called. This allows ulpi driver writers to forget about this boiler plate detail and avoids common bugs in the process. Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 13:38:21 +08:00
drv->driver.owner = module;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
drv->driver.bus = &ulpi_bus;
return driver_register(&drv->driver);
}
usb: ulpi: Automatically set driver::owner with ulpi_driver_register() Let's follow other driver registration functions and automatically set the driver's owner member to THIS_MODULE when ulpi_driver_register() is called. This allows ulpi driver writers to forget about this boiler plate detail and avoids common bugs in the process. Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 13:38:21 +08:00
EXPORT_SYMBOL_GPL(__ulpi_register_driver);
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
/**
* ulpi_unregister_driver - unregister a driver with the ULPI bus
* @drv: driver to unregister
*
* Unregisters a driver with the ULPI bus.
*/
void ulpi_unregister_driver(struct ulpi_driver *drv)
{
driver_unregister(&drv->driver);
}
EXPORT_SYMBOL_GPL(ulpi_unregister_driver);
/* -------------------------------------------------------------------------- */
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
static int ulpi_of_register(struct ulpi *ulpi)
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
{
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
struct device_node *np = NULL, *child;
struct device *parent;
/* Find a ulpi bus underneath the parent or the grandparent */
parent = ulpi->dev.parent;
if (parent->of_node)
USB: ulpi: fix bus-node lookup Fix bus-node lookup during registration, which ended up searching the whole device tree depth-first starting at the parent (or grand parent) rather than just matching on its children. To make things worse, the parent (or grand-parent) node could end being prematurely freed as well. Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Reported-by: Peter Robinson <pbrobinson@gmail.com> Reported-by: Stephen Boyd <sboyd@codeaurora.org> Cc: stable <stable@vger.kernel.org> # 4.10 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-11 23:31:18 +08:00
np = of_get_child_by_name(parent->of_node, "ulpi");
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
else if (parent->parent && parent->parent->of_node)
USB: ulpi: fix bus-node lookup Fix bus-node lookup during registration, which ended up searching the whole device tree depth-first starting at the parent (or grand parent) rather than just matching on its children. To make things worse, the parent (or grand-parent) node could end being prematurely freed as well. Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Reported-by: Peter Robinson <pbrobinson@gmail.com> Reported-by: Stephen Boyd <sboyd@codeaurora.org> Cc: stable <stable@vger.kernel.org> # 4.10 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-11 23:31:18 +08:00
np = of_get_child_by_name(parent->parent->of_node, "ulpi");
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
if (!np)
return 0;
child = of_get_next_available_child(np, NULL);
of_node_put(np);
if (!child)
return -EINVAL;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
ulpi->dev.of_node = child;
return 0;
}
static int ulpi_read_id(struct ulpi *ulpi)
{
int ret;
usb: ulpi: move setting of ulpi->dev parent up in ulpi_register() Once ulpi operations use the parent device directly, this will be needed during the operations used in ulpi_register() itself, so set the parent field before calling any ulpi operations. Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Tal Shorer <tal.shorer@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-17 00:04:46 +08:00
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
/* Test the interface */
ret = ulpi_write(ulpi, ULPI_SCRATCH, 0xaa);
if (ret < 0)
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
goto err;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
ret = ulpi_read(ulpi, ULPI_SCRATCH);
if (ret < 0)
return ret;
if (ret != 0xaa)
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
goto err;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
ulpi->id.vendor = ulpi_read(ulpi, ULPI_VENDOR_ID_LOW);
ulpi->id.vendor |= ulpi_read(ulpi, ULPI_VENDOR_ID_HIGH) << 8;
ulpi->id.product = ulpi_read(ulpi, ULPI_PRODUCT_ID_LOW);
ulpi->id.product |= ulpi_read(ulpi, ULPI_PRODUCT_ID_HIGH) << 8;
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
/* Some ULPI devices don't have a vendor id so rely on OF match */
if (ulpi->id.vendor == 0)
goto err;
request_module("ulpi:v%04xp%04x", ulpi->id.vendor, ulpi->id.product);
return 0;
err:
of_device_request_module(&ulpi->dev);
return 0;
}
static int ulpi_register(struct device *dev, struct ulpi *ulpi)
{
int ret;
ulpi->dev.parent = dev; /* needed early for ops */
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
ulpi->dev.bus = &ulpi_bus;
ulpi->dev.type = &ulpi_dev_type;
dev_set_name(&ulpi->dev, "%s.ulpi", dev_name(dev));
ACPI_COMPANION_SET(&ulpi->dev, ACPI_COMPANION(dev));
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
ret = ulpi_of_register(ulpi);
if (ret)
return ret;
ret = ulpi_read_id(ulpi);
if (ret)
return ret;
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
ret = device_register(&ulpi->dev);
if (ret)
return ret;
dev_dbg(&ulpi->dev, "registered ULPI PHY: vendor %04x, product %04x\n",
ulpi->id.vendor, ulpi->id.product);
return 0;
}
/**
* ulpi_register_interface - instantiate new ULPI device
* @dev: USB controller's device interface
* @ops: ULPI register access
*
* Allocates and registers a ULPI device and an interface for it. Called from
* the USB controller that provides the ULPI interface.
*/
usb: ulpi: make ops struct constant None of the core ulpi functions perform any changes to the operations struct, and logically as a struct that contains function pointers there's no reason it shouldn't be constant. Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Tal Shorer <tal.shorer@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-17 00:04:52 +08:00
struct ulpi *ulpi_register_interface(struct device *dev,
const struct ulpi_ops *ops)
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
{
struct ulpi *ulpi;
int ret;
ulpi = kzalloc(sizeof(*ulpi), GFP_KERNEL);
if (!ulpi)
return ERR_PTR(-ENOMEM);
ulpi->ops = ops;
ret = ulpi_register(dev, ulpi);
if (ret) {
kfree(ulpi);
return ERR_PTR(ret);
}
return ulpi;
}
EXPORT_SYMBOL_GPL(ulpi_register_interface);
/**
* ulpi_unregister_interface - unregister ULPI interface
* @intrf: struct ulpi_interface
*
* Unregisters a ULPI device and it's interface that was created with
* ulpi_create_interface().
*/
void ulpi_unregister_interface(struct ulpi *ulpi)
{
usb: ulpi: Support device discovery via DT The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com>
2016-12-29 06:56:49 +08:00
of_node_put(ulpi->dev.of_node);
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
device_unregister(&ulpi->dev);
}
EXPORT_SYMBOL_GPL(ulpi_unregister_interface);
/* -------------------------------------------------------------------------- */
static int __init ulpi_init(void)
{
return bus_register(&ulpi_bus);
}
usb: ulpi: ulpi_init should be executed in subsys_initcall Phy drivers and the ulpi interface providers depend on the registration of the ulpi bus. Ulpi registers the bus in module_init(). This could cause unnecessary bus users' probe delays. i.e. unnecessary -EPROBE_DEFER happening on ulpi_drivers in case they're registered before ulpi bus itself. Reported-by: Zhuo Qiuxu <qiuxu.zhuo@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-06-04 20:44:14 +08:00
subsys_initcall(ulpi_init);
usb: add bus type for USB ULPI UTMI+ Low Pin Interface (ULPI) is a commonly used PHY interface for USB 2.0. The ULPI specification describes a standard set of registers which the vendors can extend for their specific needs. ULPI PHYs provide often functions such as charger detection and ADP sensing and probing. There are two major issues that the bus type is meant to tackle: Firstly, ULPI registers are accessed from the controller. The bus provides convenient method for the controller drivers to share that access with the actual PHY drivers. Secondly, there are already platforms that assume ULPI PHYs are runtime detected, such as many Intel Baytrail based platforms. They do not provide any kind of hardware description for the ULPI PHYs like separate ACPI device object that could be used to enumerate a device from. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 20:26:42 +08:00
static void __exit ulpi_exit(void)
{
bus_unregister(&ulpi_bus);
}
module_exit(ulpi_exit);
MODULE_AUTHOR("Intel Corporation");
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("USB ULPI PHY bus");