linux-sg2042/drivers/pinctrl/sirf/Makefile

# CSR SiRFsoc pinmux support

obj-y	+= pinctrl-sirf.o
obj-y	+= pinctrl-prima2.o
obj-y	+= pinctrl-atlas6.o
obj-y	+= pinctrl-atlas7.o
pinctrl:sirf:re-arch and add support for new SiRFatlas6 SoC atlas6 is a SoC very similar with primaII, the register layput of pinctrl is same, but the pads, groups and functions of atlas6 have different layout with prima2, this patch 1. pull the definition of pads, groups and functions out of the pinctrl-sirf driver,and put them into soc-specific files 2. add pads, groups and functions tables for atlas6 3. let pads, groups and functions tables become the config data of the related dt compatible node, so the pinctrl-sirf can support all SiRF SoCs with the config data as private data. In this patch,we create a sirf dir, and let the old drivers/pinctrl/pinctrl-sirf.c = drivers/pinctrl/sirf/pinctrl-prima2.c + drivers/pinctrl/sirf/pinctrl-sirf.c drivers/pinctrl/sirf/pinctrl-atlas6.c is a newly created file for the pin layout of atlas6. Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2013-05-14 22:17:58 +08:00			`# CSR SiRFsoc pinmux support`

			`obj-y += pinctrl-sirf.o`
			`obj-y += pinctrl-prima2.o`
			`obj-y += pinctrl-atlas6.o`
pinctrl: sirf: add sirf atlas7 pinctrl and gpio support The Pinctrl module (ioc) controls the Pad's function select (each pad can have 8 functions), Pad's Drive Strength, Pad's Pull Select and Pad's Input Disable status. The ioc has two modules, ioc_top & ioc_rtc. Both of these two modules have function select/clear, Pull select and Drive Strength registers. But only ioc_rtc has input-disable registers. The Pads on ioc_top have to access ioc_rtc to set their input-disable status and intpu-disable-value. So have to use one ioc driver instance to drive these two ioc modules at the same time, and each ioc module will be treat as one bank on the "IOC Device". The GPIO Controller controls the GPIO status if the Pad has been config as GPIO by Pinctrl already. Includes the GPIO Input/output, Interrupt type, Interrupt Status, and Set/Get Values. The GPIO pull up/down are controlled by Pinctrl. There are 7 GPIO Groups and splited into 3 MACROs in atlas7. The GPIO Groups in one MACRO share one GPIO controllers, each GPIO Group are treated as one GPIO bank. For example: In VDIFM macro, there is one GPIO Controller, it has 3 banks to control 3 gpio groups. Its gpio name space is from 0 to 95. The Device Tree can be written as following: gpio-ranges = <&pinctrl 0 0 0>, <&pinctrl 32 0 0>, <&pinctrl 64 0 0>; gpio-ranges-group-names = "gnss_gpio_grp", "lcd_vip_gpio_grp", "sdio_i2s_gpio_grp"; bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp". bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp". bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp". Signed-off-by: Wei Chen <Wei.Chen@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2015-05-18 15:28:32 +08:00			`obj-y += pinctrl-atlas7.o`