linux-sg2042/drivers/gpio/Makefile

97 lines
4.0 KiB
Makefile
Raw Normal View History

# generic gpio support: platform drivers, dedicated expander chips, etc
ccflags-$(CONFIG_DEBUG_GPIO) += -DDEBUG
obj-$(CONFIG_GPIO_DEVRES) += devres.o
obj-$(CONFIG_GPIOLIB) += gpiolib.o
obj-$(CONFIG_OF_GPIO) += gpiolib-of.o
obj-$(CONFIG_GPIO_ACPI) += gpiolib-acpi.o
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 14:28:20 +08:00
# Device drivers. Generally keep list sorted alphabetically
obj-$(CONFIG_GPIO_GENERIC) += gpio-generic.o
obj-$(CONFIG_GPIO_74X164) += gpio-74x164.o
obj-$(CONFIG_GPIO_ADNP) += gpio-adnp.o
obj-$(CONFIG_GPIO_ADP5520) += gpio-adp5520.o
obj-$(CONFIG_GPIO_ADP5588) += gpio-adp5588.o
obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o
obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o
obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o
obj-$(CONFIG_GPIO_CLPS711X) += gpio-clps711x.o
obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_GPIO_DA9055) += gpio-da9055.o
obj-$(CONFIG_ARCH_DAVINCI) += gpio-davinci.o
obj-$(CONFIG_GPIO_EM) += gpio-em.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
obj-$(CONFIG_GPIO_F7188X) += gpio-f7188x.o
obj-$(CONFIG_GPIO_GE_FPGA) += gpio-ge.o
obj-$(CONFIG_GPIO_GRGPIO) += gpio-grgpio.o
obj-$(CONFIG_GPIO_ICH) += gpio-ich.o
obj-$(CONFIG_GPIO_IOP) += gpio-iop.o
obj-$(CONFIG_GPIO_IT8761E) += gpio-it8761e.o
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
obj-$(CONFIG_GPIO_KEMPLD) += gpio-kempld.o
obj-$(CONFIG_ARCH_KS8695) += gpio-ks8695.o
obj-$(CONFIG_GPIO_LANGWELL) += gpio-langwell.o
obj-$(CONFIG_ARCH_LPC32XX) += gpio-lpc32xx.o
obj-$(CONFIG_GPIO_LYNXPOINT) += gpio-lynxpoint.o
obj-$(CONFIG_GPIO_MAX730X) += gpio-max730x.o
obj-$(CONFIG_GPIO_MAX7300) += gpio-max7300.o
obj-$(CONFIG_GPIO_MAX7301) += gpio-max7301.o
obj-$(CONFIG_GPIO_MAX732X) += gpio-max732x.o
obj-$(CONFIG_GPIO_MC33880) += gpio-mc33880.o
obj-$(CONFIG_GPIO_MC9S08DZ60) += gpio-mc9s08dz60.o
obj-$(CONFIG_GPIO_MCP23S08) += gpio-mcp23s08.o
obj-$(CONFIG_GPIO_ML_IOH) += gpio-ml-ioh.o
obj-$(CONFIG_GPIO_MM_LANTIQ) += gpio-mm-lantiq.o
obj-$(CONFIG_GPIO_MPC5200) += gpio-mpc5200.o
obj-$(CONFIG_GPIO_MPC8XXX) += gpio-mpc8xxx.o
obj-$(CONFIG_GPIO_MSIC) += gpio-msic.o
obj-$(CONFIG_GPIO_MSM_V1) += gpio-msm-v1.o
obj-$(CONFIG_GPIO_MSM_V2) += gpio-msm-v2.o
obj-$(CONFIG_GPIO_MVEBU) += gpio-mvebu.o
obj-$(CONFIG_GPIO_MXC) += gpio-mxc.o
obj-$(CONFIG_GPIO_MXS) += gpio-mxs.o
obj-$(CONFIG_GPIO_OCTEON) += gpio-octeon.o
obj-$(CONFIG_ARCH_OMAP) += gpio-omap.o
obj-$(CONFIG_GPIO_PCA953X) += gpio-pca953x.o
obj-$(CONFIG_GPIO_PCF857X) += gpio-pcf857x.o
obj-$(CONFIG_GPIO_PCH) += gpio-pch.o
obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o
obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o
obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o
obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o
obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o
obj-$(CONFIG_GPIO_SAMSUNG) += gpio-samsung.o
obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o
obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o
obj-$(CONFIG_GPIO_STA2X11) += gpio-sta2x11.o
obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
obj-$(CONFIG_GPIO_STP_XWAY) += gpio-stp-xway.o
obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o
obj-$(CONFIG_ARCH_TEGRA) += gpio-tegra.o
obj-$(CONFIG_GPIO_TIMBERDALE) += gpio-timberdale.o
obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o
obj-$(CONFIG_GPIO_PALMAS) += gpio-palmas.o
obj-$(CONFIG_GPIO_TPS6586X) += gpio-tps6586x.o
obj-$(CONFIG_GPIO_TPS65910) += gpio-tps65910.o
obj-$(CONFIG_GPIO_TPS65912) += gpio-tps65912.o
obj-$(CONFIG_GPIO_TS5500) += gpio-ts5500.o
obj-$(CONFIG_GPIO_TWL4030) += gpio-twl4030.o
obj-$(CONFIG_GPIO_TWL6040) += gpio-twl6040.o
gpio-tz1090: add TZ1090 gpio driver Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC. This doesn't include low-power GPIOs as they're controlled separately via the Powerdown Controller (PDC) registers. The driver is instantiated by device tree and supports interrupts for all GPIOs. Changes in v4: - fix typos in DT bindings compatible properties - reference Documentation/devicetree/bindings/gpio/gpio.txt in gpio-ranges description in DT bindings - fix gpio-ranges examples in DT bindings (it must now have 3 cells) - gpio-tz1090: use of_property_read_u32 instead of of_get_property Changes in v3: - separated from irq-imgpdc and removed arch/metag changes to allow these patches to go upstream separately via the pinctrl[/gpio] trees (particularly the pinctrl drivers depend on the new pinconf DT bindings). - some s/unsigned/unsigned int/. - some s/unsigned int/bool/ and use of BIT(). - gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and <dt-bindings/interrupt-controller/irq.h> flags in bindings. - gpio-tz1090*: move initcall from postcore to subsys. - gpio-tz1090: add REG_ prefix to some constants for consistency. - gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge cunningness. Changes in v2: - gpio-tz1090: remove references to Linux flags in dt bindings - gpio-tz1090: make use of BIT() from linux/bitops.h - gpio-tz1090: make register accessors inline to match pinctrl - gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI breakage Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Rob Landley <rob@landley.net> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-doc@vger.kernel.org Cc: devicetree-discuss@lists.ozlabs.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-06-25 22:27:43 +08:00
obj-$(CONFIG_GPIO_TZ1090) += gpio-tz1090.o
gpio-tz1090-pdc: add TZ1090 PDC gpio driver Add a GPIO driver for the low-power Powerdown Controller GPIOs in the TZ1090 SoC. The driver is instantiated by device tree and supports interrupts for the SysWake GPIOs only. Changes in v4: - fix typos in DT bindings compatible properties - reference Documentation/devicetree/bindings/gpio/gpio.txt in gpio-ranges description in DT bindings - fix gpio-ranges examples in DT bindings (it must now have 3 cells) Changes in v3: - separated from irq-imgpdc and removed arch/metag changes to allow these patches to go upstream separately via the pinctrl[/gpio] trees (particularly the pinctrl drivers depend on the new pinconf DT bindings). - some s/unsigned/unsigned int/. - gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and <dt-bindings/interrupt-controller/irq.h> flags in bindings. - gpio-tz1090*: move initcall from postcore to subsys. Changes in v2: - gpio-tz1090-pdc: remove references to Linux flags in dt bindings - gpio-tz1090-pdc: make use of BIT() from linux/bitops.h - gpio-tz1090-pdc: make register accessors inline to match pinctrl - gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI breakage Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Rob Landley <rob@landley.net> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-doc@vger.kernel.org Cc: devicetree-discuss@lists.ozlabs.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-06-25 22:27:44 +08:00
obj-$(CONFIG_GPIO_TZ1090_PDC) += gpio-tz1090-pdc.o
obj-$(CONFIG_GPIO_UCB1400) += gpio-ucb1400.o
obj-$(CONFIG_GPIO_VIPERBOARD) += gpio-viperboard.o
obj-$(CONFIG_GPIO_VR41XX) += gpio-vr41xx.o
obj-$(CONFIG_GPIO_VX855) += gpio-vx855.o
obj-$(CONFIG_GPIO_WM831X) += gpio-wm831x.o
obj-$(CONFIG_GPIO_WM8350) += gpio-wm8350.o
obj-$(CONFIG_GPIO_WM8994) += gpio-wm8994.o
obj-$(CONFIG_GPIO_XILINX) += gpio-xilinx.o