linux-sg2042/drivers/iio/adc/xilinx-xadc.h

215 lines
5.7 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0-only */
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
/*
* Xilinx XADC driver
*
* Copyright 2013 Analog Devices Inc.
* Author: Lars-Peter Clausen <lars@metafoo.de>
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
*/
#ifndef __IIO_XILINX_XADC__
#define __IIO_XILINX_XADC__
#include <linux/interrupt.h>
#include <linux/mutex.h>
#include <linux/spinlock.h>
struct iio_dev;
struct clk;
struct xadc_ops;
struct platform_device;
void xadc_handle_events(struct iio_dev *indio_dev, unsigned long events);
int xadc_read_event_config(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, enum iio_event_type type,
enum iio_event_direction dir);
int xadc_write_event_config(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, enum iio_event_type type,
enum iio_event_direction dir, int state);
int xadc_read_event_value(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, enum iio_event_type type,
enum iio_event_direction dir, enum iio_event_info info,
int *val, int *val2);
int xadc_write_event_value(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan, enum iio_event_type type,
enum iio_event_direction dir, enum iio_event_info info,
int val, int val2);
enum xadc_external_mux_mode {
XADC_EXTERNAL_MUX_NONE,
XADC_EXTERNAL_MUX_SINGLE,
XADC_EXTERNAL_MUX_DUAL,
};
struct xadc {
void __iomem *base;
struct clk *clk;
const struct xadc_ops *ops;
uint16_t threshold[16];
uint16_t temp_hysteresis;
unsigned int alarm_mask;
uint16_t *data;
struct iio_trigger *trigger;
struct iio_trigger *convst_trigger;
struct iio_trigger *samplerate_trigger;
enum xadc_external_mux_mode external_mux_mode;
unsigned int zynq_masked_alarm;
unsigned int zynq_intmask;
struct delayed_work zynq_unmask_work;
struct mutex mutex;
spinlock_t lock;
struct completion completion;
};
enum xadc_type {
XADC_TYPE_S7, /* Series 7 */
XADC_TYPE_US, /* UltraScale and UltraScale+ */
};
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
struct xadc_ops {
int (*read)(struct xadc *xadc, unsigned int reg, uint16_t *val);
int (*write)(struct xadc *xadc, unsigned int reg, uint16_t val);
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
int (*setup)(struct platform_device *pdev, struct iio_dev *indio_dev,
int irq);
void (*update_alarm)(struct xadc *xadc, unsigned int alarm);
unsigned long (*get_dclk_rate)(struct xadc *xadc);
irqreturn_t (*interrupt_handler)(int irq, void *devid);
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
unsigned int flags;
enum xadc_type type;
int temp_scale;
int temp_offset;
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
};
static inline int _xadc_read_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t *val)
{
lockdep_assert_held(&xadc->mutex);
return xadc->ops->read(xadc, reg, val);
}
static inline int _xadc_write_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t val)
{
lockdep_assert_held(&xadc->mutex);
return xadc->ops->write(xadc, reg, val);
}
static inline int xadc_read_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t *val)
{
int ret;
mutex_lock(&xadc->mutex);
ret = _xadc_read_adc_reg(xadc, reg, val);
mutex_unlock(&xadc->mutex);
return ret;
}
static inline int xadc_write_adc_reg(struct xadc *xadc, unsigned int reg,
uint16_t val)
{
int ret;
mutex_lock(&xadc->mutex);
ret = _xadc_write_adc_reg(xadc, reg, val);
mutex_unlock(&xadc->mutex);
return ret;
}
/* XADC hardmacro register definitions */
#define XADC_REG_TEMP 0x00
#define XADC_REG_VCCINT 0x01
#define XADC_REG_VCCAUX 0x02
#define XADC_REG_VPVN 0x03
#define XADC_REG_VREFP 0x04
#define XADC_REG_VREFN 0x05
#define XADC_REG_VCCBRAM 0x06
#define XADC_REG_VCCPINT 0x0d
#define XADC_REG_VCCPAUX 0x0e
#define XADC_REG_VCCO_DDR 0x0f
#define XADC_REG_VAUX(x) (0x10 + (x))
#define XADC_REG_MAX_TEMP 0x20
#define XADC_REG_MAX_VCCINT 0x21
#define XADC_REG_MAX_VCCAUX 0x22
#define XADC_REG_MAX_VCCBRAM 0x23
#define XADC_REG_MIN_TEMP 0x24
#define XADC_REG_MIN_VCCINT 0x25
#define XADC_REG_MIN_VCCAUX 0x26
#define XADC_REG_MIN_VCCBRAM 0x27
#define XADC_REG_MAX_VCCPINT 0x28
#define XADC_REG_MAX_VCCPAUX 0x29
#define XADC_REG_MAX_VCCO_DDR 0x2a
#define XADC_REG_MIN_VCCPINT 0x2c
#define XADC_REG_MIN_VCCPAUX 0x2d
#define XADC_REG_MIN_VCCO_DDR 0x2e
iio:adc: Add Xilinx XADC driver The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx. The XADC has a DRP interface for communication. Currently two different frontends for the DRP interface exist. One that is only available on the ZYNQ family as a hardmacro in the SoC portion of the ZYNQ. The other one is available on all series 7 platforms and is a softmacro with a AXI interface. This driver supports both interfaces and internally has a small abstraction layer that hides the specifics of these interfaces from the main driver logic. The ADC has a couple of internal channels which are used for voltage and temperature monitoring of the FPGA as well as one primary and up to 16 channels auxiliary channels for measuring external voltages. The external auxiliary channels can either be directly connected each to one physical pin on the FPGA or they can make use of an external multiplexer which is responsible for multiplexing the external signals onto one pair of physical pins. The voltage and temperature monitoring channels also have an event capability which allows to generate a interrupt when their value falls below or raises above a set threshold. Buffered sampling mode is supported by the driver, but only for AXI-XADC since the ZYNQ XADC interface does not have capabilities for supporting buffer mode (no end-of-conversion interrupt). If buffered mode is supported the driver will register two triggers. One "xadc-samplerate" trigger which will generate samples with the configured samplerate. And one "xadc-convst" trigger which will generate one sample each time the CONVST (conversion start) signal is asserted. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-02-17 22:10:00 +08:00
#define XADC_REG_CONF0 0x40
#define XADC_REG_CONF1 0x41
#define XADC_REG_CONF2 0x42
#define XADC_REG_SEQ(x) (0x48 + (x))
#define XADC_REG_INPUT_MODE(x) (0x4c + (x))
#define XADC_REG_THRESHOLD(x) (0x50 + (x))
#define XADC_REG_FLAG 0x3f
#define XADC_CONF0_EC BIT(9)
#define XADC_CONF0_ACQ BIT(8)
#define XADC_CONF0_MUX BIT(11)
#define XADC_CONF0_CHAN(x) (x)
#define XADC_CONF1_SEQ_MASK (0xf << 12)
#define XADC_CONF1_SEQ_DEFAULT (0 << 12)
#define XADC_CONF1_SEQ_SINGLE_PASS (1 << 12)
#define XADC_CONF1_SEQ_CONTINUOUS (2 << 12)
#define XADC_CONF1_SEQ_SINGLE_CHANNEL (3 << 12)
#define XADC_CONF1_SEQ_SIMULTANEOUS (4 << 12)
#define XADC_CONF1_SEQ_INDEPENDENT (8 << 12)
#define XADC_CONF1_ALARM_MASK 0x0f0f
#define XADC_CONF2_DIV_MASK 0xff00
#define XADC_CONF2_DIV_OFFSET 8
#define XADC_CONF2_PD_MASK (0x3 << 4)
#define XADC_CONF2_PD_NONE (0x0 << 4)
#define XADC_CONF2_PD_ADC_B (0x2 << 4)
#define XADC_CONF2_PD_BOTH (0x3 << 4)
#define XADC_ALARM_TEMP_MASK BIT(0)
#define XADC_ALARM_VCCINT_MASK BIT(1)
#define XADC_ALARM_VCCAUX_MASK BIT(2)
#define XADC_ALARM_OT_MASK BIT(3)
#define XADC_ALARM_VCCBRAM_MASK BIT(4)
#define XADC_ALARM_VCCPINT_MASK BIT(5)
#define XADC_ALARM_VCCPAUX_MASK BIT(6)
#define XADC_ALARM_VCCODDR_MASK BIT(7)
#define XADC_THRESHOLD_TEMP_MAX 0x0
#define XADC_THRESHOLD_VCCINT_MAX 0x1
#define XADC_THRESHOLD_VCCAUX_MAX 0x2
#define XADC_THRESHOLD_OT_MAX 0x3
#define XADC_THRESHOLD_TEMP_MIN 0x4
#define XADC_THRESHOLD_VCCINT_MIN 0x5
#define XADC_THRESHOLD_VCCAUX_MIN 0x6
#define XADC_THRESHOLD_OT_MIN 0x7
#define XADC_THRESHOLD_VCCBRAM_MAX 0x8
#define XADC_THRESHOLD_VCCPINT_MAX 0x9
#define XADC_THRESHOLD_VCCPAUX_MAX 0xa
#define XADC_THRESHOLD_VCCODDR_MAX 0xb
#define XADC_THRESHOLD_VCCBRAM_MIN 0xc
#define XADC_THRESHOLD_VCCPINT_MIN 0xd
#define XADC_THRESHOLD_VCCPAUX_MIN 0xe
#define XADC_THRESHOLD_VCCODDR_MIN 0xf
#endif