linux-sg2042/drivers/usb/host/isp1760-hcd.c

2331 lines
56 KiB
C
Raw Normal View History

/*
* Driver for the NXP ISP1760 chip
*
* However, the code might contain some bugs. What doesn't work for sure is:
* - ISO
* - OTG
e The interrupt line is configured as active low, level.
*
* (c) 2007 Sebastian Siewior <bigeasy@linutronix.de>
*
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/list.h>
#include <linux/usb.h>
#include <linux/usb/hcd.h>
#include <linux/debugfs.h>
#include <linux/uaccess.h>
#include <linux/io.h>
#include <linux/mm.h>
#include <asm/unaligned.h>
#include <asm/cacheflush.h>
#include "isp1760-hcd.h"
static struct kmem_cache *qtd_cachep;
static struct kmem_cache *qh_cachep;
struct isp1760_hcd {
u32 hcs_params;
spinlock_t lock;
struct inter_packet_info atl_ints[32];
struct inter_packet_info int_ints[32];
struct memory_chunk memory_pool[BLOCKS];
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
u32 atl_queued;
/* periodic schedule support */
#define DEFAULT_I_TDPS 1024
unsigned periodic_size;
unsigned i_thresh;
unsigned long reset_done;
unsigned long next_statechange;
unsigned int devflags;
};
static inline struct isp1760_hcd *hcd_to_priv(struct usb_hcd *hcd)
{
return (struct isp1760_hcd *) (hcd->hcd_priv);
}
static inline struct usb_hcd *priv_to_hcd(struct isp1760_hcd *priv)
{
return container_of((void *) priv, struct usb_hcd, hcd_priv);
}
/* Section 2.2 Host Controller Capability Registers */
#define HC_LENGTH(p) (((p)>>00)&0x00ff) /* bits 7:0 */
#define HC_VERSION(p) (((p)>>16)&0xffff) /* bits 31:16 */
#define HCS_INDICATOR(p) ((p)&(1 << 16)) /* true: has port indicators */
#define HCS_PPC(p) ((p)&(1 << 4)) /* true: port power control */
#define HCS_N_PORTS(p) (((p)>>0)&0xf) /* bits 3:0, ports on HC */
#define HCC_ISOC_CACHE(p) ((p)&(1 << 7)) /* true: can cache isoc frame */
#define HCC_ISOC_THRES(p) (((p)>>4)&0x7) /* bits 6:4, uframes cached */
/* Section 2.3 Host Controller Operational Registers */
#define CMD_LRESET (1<<7) /* partial reset (no ports, etc) */
#define CMD_RESET (1<<1) /* reset HC not bus */
#define CMD_RUN (1<<0) /* start/stop HC */
#define STS_PCD (1<<2) /* port change detect */
#define FLAG_CF (1<<0) /* true: we'll support "high speed" */
#define PORT_OWNER (1<<13) /* true: companion hc owns this port */
#define PORT_POWER (1<<12) /* true: has power (see PPC) */
#define PORT_USB11(x) (((x) & (3 << 10)) == (1 << 10)) /* USB 1.1 device */
#define PORT_RESET (1<<8) /* reset port */
#define PORT_SUSPEND (1<<7) /* suspend port */
#define PORT_RESUME (1<<6) /* resume it */
#define PORT_PE (1<<2) /* port enable */
#define PORT_CSC (1<<1) /* connect status change */
#define PORT_CONNECT (1<<0) /* device connected */
#define PORT_RWC_BITS (PORT_CSC)
struct isp1760_qtd {
struct isp1760_qtd *hw_next;
u8 packet_type;
u8 toggle;
void *data_buffer;
/* the rest is HCD-private */
struct list_head qtd_list;
struct urb *urb;
size_t length;
/* isp special*/
u32 status;
#define URB_COMPLETE_NOTIFY (1 << 0)
#define URB_ENQUEUED (1 << 1)
#define URB_TYPE_ATL (1 << 2)
#define URB_TYPE_INT (1 << 3)
};
struct isp1760_qh {
/* first part defined by EHCI spec */
struct list_head qtd_list;
struct isp1760_hcd *priv;
/* periodic schedule info */
unsigned short period; /* polling interval */
struct usb_device *dev;
u32 toggle;
u32 ping;
};
#define ehci_port_speed(priv, portsc) USB_PORT_STAT_HIGH_SPEED
/*
* Access functions for isp176x registers (addresses 0..0x03FF).
*/
static u32 reg_read32(void __iomem *base, u32 reg)
{
return readl(base + reg);
}
static void reg_write32(void __iomem *base, u32 reg, u32 val)
{
writel(val, base + reg);
}
/*
* Access functions for isp176x memory (offset >= 0x0400).
*
* bank_reads8() reads memory locations prefetched by an earlier write to
* HC_MEMORY_REG (see isp176x datasheet). Unless you want to do fancy multi-
* bank optimizations, you should use the more generic mem_reads8() below.
*
* For access to ptd memory, use the specialized ptd_read() and ptd_write()
* below.
*
* These functions copy via MMIO data to/from the device. memcpy_{to|from}io()
* doesn't quite work because some people have to enforce 32-bit access
*/
static void bank_reads8(void __iomem *src_base, u32 src_offset, u32 bank_addr,
__u32 *dst, u32 bytes)
{
__u32 __iomem *src;
u32 val;
__u8 *src_byteptr;
__u8 *dst_byteptr;
src = src_base + (bank_addr | src_offset);
if (src_offset < PAYLOAD_OFFSET) {
while (bytes >= 4) {
*dst = le32_to_cpu(__raw_readl(src));
bytes -= 4;
src++;
dst++;
}
} else {
while (bytes >= 4) {
*dst = __raw_readl(src);
bytes -= 4;
src++;
dst++;
}
}
if (!bytes)
return;
/* in case we have 3, 2 or 1 by left. The dst buffer may not be fully
* allocated.
*/
if (src_offset < PAYLOAD_OFFSET)
val = le32_to_cpu(__raw_readl(src));
else
val = __raw_readl(src);
dst_byteptr = (void *) dst;
src_byteptr = (void *) &val;
while (bytes > 0) {
*dst_byteptr = *src_byteptr;
dst_byteptr++;
src_byteptr++;
bytes--;
}
}
static void mem_reads8(void __iomem *src_base, u32 src_offset, void *dst,
u32 bytes)
{
reg_write32(src_base, HC_MEMORY_REG, src_offset + ISP_BANK(0));
ndelay(90);
bank_reads8(src_base, src_offset, ISP_BANK(0), dst, bytes);
}
static void mem_writes8(void __iomem *dst_base, u32 dst_offset,
__u32 const *src, u32 bytes)
{
__u32 __iomem *dst;
dst = dst_base + dst_offset;
if (dst_offset < PAYLOAD_OFFSET) {
while (bytes >= 4) {
__raw_writel(cpu_to_le32(*src), dst);
bytes -= 4;
src++;
dst++;
}
} else {
while (bytes >= 4) {
__raw_writel(*src, dst);
bytes -= 4;
src++;
dst++;
}
}
if (!bytes)
return;
/* in case we have 3, 2 or 1 bytes left. The buffer is allocated and the
* extra bytes should not be read by the HW.
*/
if (dst_offset < PAYLOAD_OFFSET)
__raw_writel(cpu_to_le32(*src), dst);
else
__raw_writel(*src, dst);
}
/*
* Read and write ptds. 'ptd_offset' should be one of ISO_PTD_OFFSET,
* INT_PTD_OFFSET, and ATL_PTD_OFFSET. 'slot' should be less than 32.
*/
static void ptd_read(void __iomem *base, u32 ptd_offset, u32 slot,
struct ptd *ptd)
{
reg_write32(base, HC_MEMORY_REG,
ISP_BANK(0) + ptd_offset + slot*sizeof(*ptd));
ndelay(90);
bank_reads8(base, ptd_offset + slot*sizeof(*ptd), ISP_BANK(0),
(void *) ptd, sizeof(*ptd));
}
static void ptd_write(void __iomem *base, u32 ptd_offset, u32 slot,
struct ptd *ptd)
{
mem_writes8(base, ptd_offset + slot*sizeof(*ptd) + sizeof(ptd->dw0),
&ptd->dw1, 7*sizeof(ptd->dw1));
/* Make sure dw0 gets written last (after other dw's and after payload)
since it contains the enable bit */
wmb();
mem_writes8(base, ptd_offset + slot*sizeof(*ptd), &ptd->dw0,
sizeof(ptd->dw0));
}
/* memory management of the 60kb on the chip from 0x1000 to 0xffff */
static void init_memory(struct isp1760_hcd *priv)
{
int i;
u32 payload;
payload = 0x1000;
for (i = 0; i < BLOCK_1_NUM; i++) {
priv->memory_pool[i].start = payload;
priv->memory_pool[i].size = BLOCK_1_SIZE;
priv->memory_pool[i].free = 1;
payload += priv->memory_pool[i].size;
}
for (i = BLOCK_1_NUM; i < BLOCK_1_NUM + BLOCK_2_NUM; i++) {
priv->memory_pool[i].start = payload;
priv->memory_pool[i].size = BLOCK_2_SIZE;
priv->memory_pool[i].free = 1;
payload += priv->memory_pool[i].size;
}
for (i = BLOCK_1_NUM + BLOCK_2_NUM; i < BLOCKS; i++) {
priv->memory_pool[i].start = payload;
priv->memory_pool[i].size = BLOCK_3_SIZE;
priv->memory_pool[i].free = 1;
payload += priv->memory_pool[i].size;
}
BUG_ON(payload - priv->memory_pool[i - 1].size > PAYLOAD_SIZE);
}
static u32 alloc_mem(struct isp1760_hcd *priv, u32 size)
{
int i;
if (!size)
return ISP1760_NULL_POINTER;
for (i = 0; i < BLOCKS; i++) {
if (priv->memory_pool[i].size >= size &&
priv->memory_pool[i].free) {
priv->memory_pool[i].free = 0;
return priv->memory_pool[i].start;
}
}
printk(KERN_ERR "ISP1760 MEM: can not allocate %d bytes of memory\n",
size);
printk(KERN_ERR "Current memory map:\n");
for (i = 0; i < BLOCKS; i++) {
printk(KERN_ERR "Pool %2d size %4d status: %d\n",
i, priv->memory_pool[i].size,
priv->memory_pool[i].free);
}
/* XXX maybe -ENOMEM could be possible */
BUG();
return 0;
}
static void free_mem(struct isp1760_hcd *priv, u32 mem)
{
int i;
if (mem == ISP1760_NULL_POINTER)
return;
for (i = 0; i < BLOCKS; i++) {
if (priv->memory_pool[i].start == mem) {
BUG_ON(priv->memory_pool[i].free);
priv->memory_pool[i].free = 1;
return ;
}
}
printk(KERN_ERR "Trying to free not-here-allocated memory :%08x\n",
mem);
BUG();
}
static void isp1760_init_regs(struct usb_hcd *hcd)
{
reg_write32(hcd->regs, HC_BUFFER_STATUS_REG, 0);
reg_write32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG, NO_TRANSFER_ACTIVE);
reg_write32(hcd->regs, HC_INT_PTD_SKIPMAP_REG, NO_TRANSFER_ACTIVE);
reg_write32(hcd->regs, HC_ISO_PTD_SKIPMAP_REG, NO_TRANSFER_ACTIVE);
reg_write32(hcd->regs, HC_ATL_PTD_DONEMAP_REG, ~NO_TRANSFER_ACTIVE);
reg_write32(hcd->regs, HC_INT_PTD_DONEMAP_REG, ~NO_TRANSFER_ACTIVE);
reg_write32(hcd->regs, HC_ISO_PTD_DONEMAP_REG, ~NO_TRANSFER_ACTIVE);
}
static int handshake(struct usb_hcd *hcd, u32 reg,
u32 mask, u32 done, int usec)
{
u32 result;
do {
result = reg_read32(hcd->regs, reg);
if (result == ~0)
return -ENODEV;
result &= mask;
if (result == done)
return 0;
udelay(1);
usec--;
} while (usec > 0);
return -ETIMEDOUT;
}
/* reset a non-running (STS_HALT == 1) controller */
static int ehci_reset(struct isp1760_hcd *priv)
{
int retval;
struct usb_hcd *hcd = priv_to_hcd(priv);
u32 command = reg_read32(hcd->regs, HC_USBCMD);
command |= CMD_RESET;
reg_write32(hcd->regs, HC_USBCMD, command);
hcd->state = HC_STATE_HALT;
priv->next_statechange = jiffies;
retval = handshake(hcd, HC_USBCMD,
CMD_RESET, 0, 250 * 1000);
return retval;
}
static void qh_destroy(struct isp1760_qh *qh)
{
BUG_ON(!list_empty(&qh->qtd_list));
kmem_cache_free(qh_cachep, qh);
}
static struct isp1760_qh *isp1760_qh_alloc(struct isp1760_hcd *priv,
gfp_t flags)
{
struct isp1760_qh *qh;
qh = kmem_cache_zalloc(qh_cachep, flags);
if (!qh)
return qh;
INIT_LIST_HEAD(&qh->qtd_list);
qh->priv = priv;
return qh;
}
/* magic numbers that can affect system performance */
#define EHCI_TUNE_CERR 3 /* 0-3 qtd retries; 0 == don't stop */
#define EHCI_TUNE_RL_HS 4 /* nak throttle; see 4.9 */
#define EHCI_TUNE_RL_TT 0
#define EHCI_TUNE_MULT_HS 1 /* 1-3 transactions/uframe; 4.10.3 */
#define EHCI_TUNE_MULT_TT 1
#define EHCI_TUNE_FLS 2 /* (small) 256 frame schedule */
/* one-time init, only for memory state */
static int priv_init(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 hcc_params;
spin_lock_init(&priv->lock);
/*
* hw default: 1K periodic list heads, one per frame.
* periodic_size can shrink by USBCMD update if hcc_params allows.
*/
priv->periodic_size = DEFAULT_I_TDPS;
/* controllers may cache some of the periodic schedule ... */
hcc_params = reg_read32(hcd->regs, HC_HCCPARAMS);
/* full frame cache */
if (HCC_ISOC_CACHE(hcc_params))
priv->i_thresh = 8;
else /* N microframes cached */
priv->i_thresh = 2 + HCC_ISOC_THRES(hcc_params);
return 0;
}
static int isp1760_hc_setup(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
int result;
u32 scratch, hwmode;
/* Setup HW Mode Control: This assumes a level active-low interrupt */
hwmode = HW_DATA_BUS_32BIT;
if (priv->devflags & ISP1760_FLAG_BUS_WIDTH_16)
hwmode &= ~HW_DATA_BUS_32BIT;
if (priv->devflags & ISP1760_FLAG_ANALOG_OC)
hwmode |= HW_ANA_DIGI_OC;
if (priv->devflags & ISP1760_FLAG_DACK_POL_HIGH)
hwmode |= HW_DACK_POL_HIGH;
if (priv->devflags & ISP1760_FLAG_DREQ_POL_HIGH)
hwmode |= HW_DREQ_POL_HIGH;
if (priv->devflags & ISP1760_FLAG_INTR_POL_HIGH)
hwmode |= HW_INTR_HIGH_ACT;
if (priv->devflags & ISP1760_FLAG_INTR_EDGE_TRIG)
hwmode |= HW_INTR_EDGE_TRIG;
/*
* We have to set this first in case we're in 16-bit mode.
* Write it twice to ensure correct upper bits if switching
* to 16-bit mode.
*/
reg_write32(hcd->regs, HC_HW_MODE_CTRL, hwmode);
reg_write32(hcd->regs, HC_HW_MODE_CTRL, hwmode);
reg_write32(hcd->regs, HC_SCRATCH_REG, 0xdeadbabe);
/* Change bus pattern */
scratch = reg_read32(hcd->regs, HC_CHIP_ID_REG);
scratch = reg_read32(hcd->regs, HC_SCRATCH_REG);
if (scratch != 0xdeadbabe) {
printk(KERN_ERR "ISP1760: Scratch test failed.\n");
return -ENODEV;
}
/* pre reset */
isp1760_init_regs(hcd);
/* reset */
reg_write32(hcd->regs, HC_RESET_REG, SW_RESET_RESET_ALL);
mdelay(100);
reg_write32(hcd->regs, HC_RESET_REG, SW_RESET_RESET_HC);
mdelay(100);
result = ehci_reset(priv);
if (result)
return result;
/* Step 11 passed */
isp1760_info(priv, "bus width: %d, oc: %s\n",
(priv->devflags & ISP1760_FLAG_BUS_WIDTH_16) ?
16 : 32, (priv->devflags & ISP1760_FLAG_ANALOG_OC) ?
"analog" : "digital");
/* ATL reset */
reg_write32(hcd->regs, HC_HW_MODE_CTRL, hwmode | ALL_ATX_RESET);
mdelay(10);
reg_write32(hcd->regs, HC_HW_MODE_CTRL, hwmode);
reg_write32(hcd->regs, HC_INTERRUPT_REG, INTERRUPT_ENABLE_MASK);
reg_write32(hcd->regs, HC_INTERRUPT_ENABLE, INTERRUPT_ENABLE_MASK);
/*
* PORT 1 Control register of the ISP1760 is the OTG control
* register on ISP1761. Since there is no OTG or device controller
* support in this driver, we use port 1 as a "normal" USB host port on
* both chips.
*/
reg_write32(hcd->regs, HC_PORT1_CTRL, PORT1_POWER | PORT1_INIT2);
mdelay(10);
priv->hcs_params = reg_read32(hcd->regs, HC_HCSPARAMS);
return priv_init(hcd);
}
static void isp1760_init_maps(struct usb_hcd *hcd)
{
/*set last maps, for iso its only 1, else 32 tds bitmap*/
reg_write32(hcd->regs, HC_ATL_PTD_LASTPTD_REG, 0x80000000);
reg_write32(hcd->regs, HC_INT_PTD_LASTPTD_REG, 0x80000000);
reg_write32(hcd->regs, HC_ISO_PTD_LASTPTD_REG, 0x00000001);
}
static void isp1760_enable_interrupts(struct usb_hcd *hcd)
{
reg_write32(hcd->regs, HC_ATL_IRQ_MASK_AND_REG, 0);
reg_write32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG, 0);
reg_write32(hcd->regs, HC_INT_IRQ_MASK_AND_REG, 0);
reg_write32(hcd->regs, HC_INT_IRQ_MASK_OR_REG, 0);
reg_write32(hcd->regs, HC_ISO_IRQ_MASK_AND_REG, 0);
reg_write32(hcd->regs, HC_ISO_IRQ_MASK_OR_REG, 0xffffffff);
/* step 23 passed */
}
static int isp1760_run(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
int retval;
u32 temp;
u32 command;
u32 chipid;
hcd->uses_new_polling = 1;
hcd->state = HC_STATE_RUNNING;
isp1760_enable_interrupts(hcd);
temp = reg_read32(hcd->regs, HC_HW_MODE_CTRL);
reg_write32(hcd->regs, HC_HW_MODE_CTRL, temp | HW_GLOBAL_INTR_EN);
command = reg_read32(hcd->regs, HC_USBCMD);
command &= ~(CMD_LRESET|CMD_RESET);
command |= CMD_RUN;
reg_write32(hcd->regs, HC_USBCMD, command);
retval = handshake(hcd, HC_USBCMD, CMD_RUN, CMD_RUN,
250 * 1000);
if (retval)
return retval;
/*
* XXX
* Spec says to write FLAG_CF as last config action, priv code grabs
* the semaphore while doing so.
*/
down_write(&ehci_cf_port_reset_rwsem);
reg_write32(hcd->regs, HC_CONFIGFLAG, FLAG_CF);
retval = handshake(hcd, HC_CONFIGFLAG, FLAG_CF, FLAG_CF, 250 * 1000);
up_write(&ehci_cf_port_reset_rwsem);
if (retval)
return retval;
chipid = reg_read32(hcd->regs, HC_CHIP_ID_REG);
isp1760_info(priv, "USB ISP %04x HW rev. %d started\n", chipid & 0xffff,
chipid >> 16);
/* PTD Register Init Part 2, Step 28 */
/* enable INTs */
isp1760_init_maps(hcd);
/* GRR this is run-once init(), being done every time the HC starts.
* So long as they're part of class devices, we can't do it init()
* since the class device isn't created that early.
*/
return 0;
}
static u32 base_to_chip(u32 base)
{
return ((base - 0x400) >> 3);
}
static void transform_into_atl(struct isp1760_hcd *priv, struct isp1760_qh *qh,
struct isp1760_qtd *qtd, struct urb *urb,
u32 payload, struct ptd *ptd)
{
u32 maxpacket;
u32 multi;
u32 pid_code;
u32 rl = RL_COUNTER;
u32 nak = NAK_COUNTER;
memset(ptd, 0, sizeof(*ptd));
/* according to 3.6.2, max packet len can not be > 0x400 */
maxpacket = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe));
multi = 1 + ((maxpacket >> 11) & 0x3);
maxpacket &= 0x7ff;
/* DW0 */
ptd->dw0 = PTD_VALID;
ptd->dw0 |= PTD_LENGTH(qtd->length);
ptd->dw0 |= PTD_MAXPACKET(maxpacket);
ptd->dw0 |= PTD_ENDPOINT(usb_pipeendpoint(urb->pipe));
ptd->dw1 = usb_pipeendpoint(urb->pipe) >> 1;
/* DW1 */
ptd->dw1 |= PTD_DEVICE_ADDR(usb_pipedevice(urb->pipe));
pid_code = qtd->packet_type;
ptd->dw1 |= PTD_PID_TOKEN(pid_code);
if (usb_pipebulk(urb->pipe))
ptd->dw1 |= PTD_TRANS_BULK;
else if (usb_pipeint(urb->pipe))
ptd->dw1 |= PTD_TRANS_INT;
if (urb->dev->speed != USB_SPEED_HIGH) {
/* split transaction */
ptd->dw1 |= PTD_TRANS_SPLIT;
if (urb->dev->speed == USB_SPEED_LOW)
ptd->dw1 |= PTD_SE_USB_LOSPEED;
ptd->dw1 |= PTD_PORT_NUM(urb->dev->ttport);
ptd->dw1 |= PTD_HUB_NUM(urb->dev->tt->hub->devnum);
/* SE bit for Split INT transfers */
if (usb_pipeint(urb->pipe) &&
(urb->dev->speed == USB_SPEED_LOW))
ptd->dw1 |= 2 << 16;
ptd->dw3 = 0;
rl = 0;
nak = 0;
} else {
ptd->dw0 |= PTD_MULTI(multi);
if (usb_pipecontrol(urb->pipe) || usb_pipebulk(urb->pipe))
ptd->dw3 = qh->ping;
else
ptd->dw3 = 0;
}
/* DW2 */
ptd->dw2 = 0;
ptd->dw2 |= PTD_DATA_START_ADDR(base_to_chip(payload));
ptd->dw2 |= PTD_RL_CNT(rl);
ptd->dw3 |= PTD_NAC_CNT(nak);
/* DW3 */
if (usb_pipecontrol(urb->pipe))
ptd->dw3 |= PTD_DATA_TOGGLE(qtd->toggle);
else
ptd->dw3 |= qh->toggle;
ptd->dw3 |= PTD_ACTIVE;
/* Cerr */
ptd->dw3 |= PTD_CERR(ERR_COUNTER);
}
static void transform_add_int(struct isp1760_hcd *priv, struct isp1760_qh *qh,
struct isp1760_qtd *qtd, struct urb *urb,
u32 payload, struct ptd *ptd)
{
u32 maxpacket;
u32 multi;
u32 numberofusofs;
u32 i;
u32 usofmask, usof;
u32 period;
maxpacket = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe));
multi = 1 + ((maxpacket >> 11) & 0x3);
maxpacket &= 0x7ff;
/* length of the data per uframe */
maxpacket = multi * maxpacket;
numberofusofs = urb->transfer_buffer_length / maxpacket;
if (urb->transfer_buffer_length % maxpacket)
numberofusofs += 1;
usofmask = 1;
usof = 0;
for (i = 0; i < numberofusofs; i++) {
usof |= usofmask;
usofmask <<= 1;
}
if (urb->dev->speed != USB_SPEED_HIGH) {
/* split */
ptd->dw5 = 0x1c;
if (qh->period >= 32)
period = qh->period / 2;
else
period = qh->period;
} else {
if (qh->period >= 8)
period = qh->period/8;
else
period = qh->period;
if (period >= 32)
period = 16;
if (qh->period >= 8) {
/* millisecond period */
period = (period << 3);
} else {
/* usof based tranmsfers */
/* minimum 4 usofs */
usof = 0x11;
}
}
ptd->dw2 |= period;
ptd->dw4 = usof;
}
static void transform_into_int(struct isp1760_hcd *priv, struct isp1760_qh *qh,
struct isp1760_qtd *qtd, struct urb *urb,
u32 payload, struct ptd *ptd)
{
transform_into_atl(priv, qh, qtd, urb, payload, ptd);
transform_add_int(priv, qh, qtd, urb, payload, ptd);
}
static int qtd_fill(struct isp1760_qtd *qtd, void *databuffer, size_t len,
u32 token)
{
int count;
qtd->data_buffer = databuffer;
qtd->packet_type = GET_QTD_TOKEN_TYPE(token);
qtd->toggle = GET_DATA_TOGGLE(token);
if (len > HC_ATL_PL_SIZE)
count = HC_ATL_PL_SIZE;
else
count = len;
qtd->length = count;
return count;
}
static int check_error(struct ptd *ptd)
{
int error = 0;
if (ptd->dw3 & DW3_HALT_BIT) {
error = -EPIPE;
if (ptd->dw3 & DW3_ERROR_BIT)
USB: isp1760: Soften DW3 X/transaction error bit handling There were some reports[1] of isp1760 USB driver malfunctioning with high speed devices, noticed on Blackfin and PowerPC targets. These reports indicated that the original Philips 'pehcd'[2] driver worked fine. We've noticed the same issue with an ARM RealView platform. This happens under load (with only some mass storage devices, not all, just as in another report[3]): error bit is set in DW3 error bit is set in DW3 error bit is set in DW3 usb 1-1.2: device descriptor read/64, error -32 It appears that the 'pehcd' driver checks the X bit only if the transaction is halted (H bit), otherwise the error is so far insignificant. The ISP176x chips were modeled after EHCI, and EHCI spec says (thanks to Alan Stern for pointing out): "Transaction errors cause the status field to be updated to reflect the type of error, but the transaction continues to be retried until the Active bit is set to 0. When the error counter reaches 0, the Halt bit is set and the Active bit is cleared." So, just as the original Philips driver, isp1760 must report the error only if the transaction error and the halt bits are set. [1] http://markmail.org/message/lx4qrlbrs2uhcnly [2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494 See pehci.c:pehci_hcd_update_error_status(). [3] http://blackfin.uclinux.org/gf/tracker/5148 Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-07 05:09:19 +08:00
pr_err("error bit is set in DW3\n");
}
if (ptd->dw3 & DW3_QTD_ACTIVE) {
printk(KERN_ERR "transfer active bit is set DW3\n");
printk(KERN_ERR "nak counter: %d, rl: %d\n",
(ptd->dw3 >> 19) & 0xf, (ptd->dw2 >> 25) & 0xf);
}
return error;
}
static void check_int_err_status(u32 dw4)
{
u32 i;
dw4 >>= 8;
for (i = 0; i < 8; i++) {
switch (dw4 & 0x7) {
case INT_UNDERRUN:
printk(KERN_ERR "ERROR: under run , %d\n", i);
break;
case INT_EXACT:
printk(KERN_ERR "ERROR: transaction error, %d\n", i);
break;
case INT_BABBLE:
printk(KERN_ERR "ERROR: babble error, %d\n", i);
break;
}
dw4 >>= 3;
}
}
static void enqueue_one_qtd(struct isp1760_qtd *qtd, struct isp1760_hcd *priv,
u32 payload)
{
u32 token;
struct usb_hcd *hcd = priv_to_hcd(priv);
token = qtd->packet_type;
if (qtd->length && (qtd->length <= HC_ATL_PL_SIZE)) {
switch (token) {
case IN_PID:
break;
case OUT_PID:
case SETUP_PID:
mem_writes8(hcd->regs, payload, qtd->data_buffer,
qtd->length);
}
}
}
static void enqueue_one_atl_qtd(u32 payload,
struct isp1760_hcd *priv, struct isp1760_qh *qh,
struct urb *urb, u32 slot, struct isp1760_qtd *qtd)
{
struct ptd ptd;
struct usb_hcd *hcd = priv_to_hcd(priv);
transform_into_atl(priv, qh, qtd, urb, payload, &ptd);
ptd_write(hcd->regs, ATL_PTD_OFFSET, slot, &ptd);
enqueue_one_qtd(qtd, priv, payload);
priv->atl_ints[slot].urb = urb;
priv->atl_ints[slot].qh = qh;
priv->atl_ints[slot].qtd = qtd;
priv->atl_ints[slot].data_buffer = qtd->data_buffer;
priv->atl_ints[slot].payload = payload;
qtd->status |= URB_ENQUEUED | URB_TYPE_ATL;
qtd->status |= slot << 16;
}
static void enqueue_one_int_qtd(u32 payload,
struct isp1760_hcd *priv, struct isp1760_qh *qh,
struct urb *urb, u32 slot, struct isp1760_qtd *qtd)
{
struct ptd ptd;
struct usb_hcd *hcd = priv_to_hcd(priv);
transform_into_int(priv, qh, qtd, urb, payload, &ptd);
ptd_write(hcd->regs, INT_PTD_OFFSET, slot, &ptd);
enqueue_one_qtd(qtd, priv, payload);
priv->int_ints[slot].urb = urb;
priv->int_ints[slot].qh = qh;
priv->int_ints[slot].qtd = qtd;
priv->int_ints[slot].data_buffer = qtd->data_buffer;
priv->int_ints[slot].payload = payload;
qtd->status |= URB_ENQUEUED | URB_TYPE_INT;
qtd->status |= slot << 16;
}
static void enqueue_an_ATL_packet(struct usb_hcd *hcd, struct isp1760_qh *qh,
struct isp1760_qtd *qtd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 skip_map, or_map;
u32 queue_entry;
u32 slot;
u32 payload;
u32 buffstatus;
/*
* When this function is called from the interrupt handler to enqueue
* a follow-up packet, the SKIP register gets written and read back
* almost immediately. With ISP1761, this register requires a delay of
* 195ns between a write and subsequent read (see section 15.1.1.3).
*/
mmiowb();
ndelay(195);
skip_map = reg_read32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG);
BUG_ON(!skip_map);
slot = __ffs(skip_map);
queue_entry = 1 << slot;
payload = alloc_mem(priv, qtd->length);
enqueue_one_atl_qtd(payload, priv, qh, qtd->urb, slot, qtd);
or_map = reg_read32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG);
or_map |= queue_entry;
reg_write32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG, or_map);
skip_map &= ~queue_entry;
reg_write32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG, skip_map);
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
priv->atl_queued++;
if (priv->atl_queued == 2)
reg_write32(hcd->regs, HC_INTERRUPT_ENABLE,
INTERRUPT_ENABLE_SOT_MASK);
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
buffstatus = reg_read32(hcd->regs, HC_BUFFER_STATUS_REG);
buffstatus |= ATL_BUFFER;
reg_write32(hcd->regs, HC_BUFFER_STATUS_REG, buffstatus);
}
static void enqueue_an_INT_packet(struct usb_hcd *hcd, struct isp1760_qh *qh,
struct isp1760_qtd *qtd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 skip_map, or_map;
u32 queue_entry;
u32 slot;
u32 payload;
u32 buffstatus;
/*
* When this function is called from the interrupt handler to enqueue
* a follow-up packet, the SKIP register gets written and read back
* almost immediately. With ISP1761, this register requires a delay of
* 195ns between a write and subsequent read (see section 15.1.1.3).
*/
mmiowb();
ndelay(195);
skip_map = reg_read32(hcd->regs, HC_INT_PTD_SKIPMAP_REG);
BUG_ON(!skip_map);
slot = __ffs(skip_map);
queue_entry = 1 << slot;
payload = alloc_mem(priv, qtd->length);
enqueue_one_int_qtd(payload, priv, qh, qtd->urb, slot, qtd);
or_map = reg_read32(hcd->regs, HC_INT_IRQ_MASK_OR_REG);
or_map |= queue_entry;
reg_write32(hcd->regs, HC_INT_IRQ_MASK_OR_REG, or_map);
skip_map &= ~queue_entry;
reg_write32(hcd->regs, HC_INT_PTD_SKIPMAP_REG, skip_map);
buffstatus = reg_read32(hcd->regs, HC_BUFFER_STATUS_REG);
buffstatus |= INT_BUFFER;
reg_write32(hcd->regs, HC_BUFFER_STATUS_REG, buffstatus);
}
static void isp1760_urb_done(struct isp1760_hcd *priv, struct urb *urb,
int status)
__releases(priv->lock)
__acquires(priv->lock)
{
if (!urb->unlinked) {
if (status == -EINPROGRESS)
status = 0;
}
if (usb_pipein(urb->pipe) && usb_pipetype(urb->pipe) != PIPE_CONTROL) {
void *ptr;
for (ptr = urb->transfer_buffer;
ptr < urb->transfer_buffer + urb->transfer_buffer_length;
ptr += PAGE_SIZE)
flush_dcache_page(virt_to_page(ptr));
}
/* complete() can reenter this HCD */
usb_hcd_unlink_urb_from_ep(priv_to_hcd(priv), urb);
spin_unlock(&priv->lock);
usb_hcd_giveback_urb(priv_to_hcd(priv), urb, status);
spin_lock(&priv->lock);
}
static void isp1760_qtd_free(struct isp1760_qtd *qtd)
{
kmem_cache_free(qtd_cachep, qtd);
}
static struct isp1760_qtd *clean_this_qtd(struct isp1760_qtd *qtd)
{
struct isp1760_qtd *tmp_qtd;
tmp_qtd = qtd->hw_next;
list_del(&qtd->qtd_list);
isp1760_qtd_free(qtd);
return tmp_qtd;
}
/*
* Remove this QTD from the QH list and free its memory. If this QTD
* isn't the last one than remove also his successor(s).
* Returns the QTD which is part of an new URB and should be enqueued.
*/
static struct isp1760_qtd *clean_up_qtdlist(struct isp1760_qtd *qtd)
{
struct isp1760_qtd *tmp_qtd;
int last_one;
do {
tmp_qtd = qtd->hw_next;
last_one = qtd->status & URB_COMPLETE_NOTIFY;
list_del(&qtd->qtd_list);
isp1760_qtd_free(qtd);
qtd = tmp_qtd;
} while (!last_one && qtd);
return qtd;
}
static void do_atl_int(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 done_map, skip_map;
struct ptd ptd;
struct urb *urb = NULL;
u32 queue_entry;
u32 payload;
u32 length;
u32 or_map;
u32 status = -EINVAL;
int error;
struct isp1760_qtd *qtd;
struct isp1760_qh *qh;
u32 rl;
u32 nakcount;
done_map = reg_read32(hcd->regs, HC_ATL_PTD_DONEMAP_REG);
skip_map = reg_read32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG);
or_map = reg_read32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG);
or_map &= ~done_map;
reg_write32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG, or_map);
while (done_map) {
status = 0;
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
priv->atl_queued--;
queue_entry = __ffs(done_map);
done_map &= ~(1 << queue_entry);
skip_map |= 1 << queue_entry;
urb = priv->atl_ints[queue_entry].urb;
qtd = priv->atl_ints[queue_entry].qtd;
qh = priv->atl_ints[queue_entry].qh;
payload = priv->atl_ints[queue_entry].payload;
if (!qh) {
printk(KERN_ERR "qh is 0\n");
continue;
}
ptd_read(hcd->regs, ATL_PTD_OFFSET, queue_entry, &ptd);
rl = (ptd.dw2 >> 25) & 0x0f;
nakcount = (ptd.dw3 >> 19) & 0xf;
/* Transfer Error, *but* active and no HALT -> reload */
if ((ptd.dw3 & DW3_ERROR_BIT) && (ptd.dw3 & DW3_QTD_ACTIVE) &&
!(ptd.dw3 & DW3_HALT_BIT)) {
/* according to ppriv code, we have to
* reload this one if trasfered bytes != requested bytes
* else act like everything went smooth..
* XXX This just doesn't feel right and hasn't
* triggered so far.
*/
length = PTD_XFERRED_LENGTH(ptd.dw3);
printk(KERN_ERR "Should reload now.... transfered %d "
"of %zu\n", length, qtd->length);
BUG();
}
if (!nakcount && (ptd.dw3 & DW3_QTD_ACTIVE)) {
u32 buffstatus;
/*
* NAKs are handled in HW by the chip. Usually if the
* device is not able to send data fast enough.
* This happens mostly on slower hardware.
*/
/* RL counter = ERR counter */
ptd.dw3 &= ~(0xf << 19);
ptd.dw3 |= rl << 19;
ptd.dw3 &= ~(3 << (55 - 32));
ptd.dw3 |= ERR_COUNTER << (55 - 32);
/*
* It is not needed to write skip map back because it
* is unchanged. Just make sure that this entry is
* unskipped once it gets written to the HW.
*/
skip_map &= ~(1 << queue_entry);
or_map = reg_read32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG);
or_map |= 1 << queue_entry;
reg_write32(hcd->regs, HC_ATL_IRQ_MASK_OR_REG, or_map);
ptd.dw0 |= PTD_VALID;
ptd_write(hcd->regs, ATL_PTD_OFFSET, queue_entry, &ptd);
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
priv->atl_queued++;
if (priv->atl_queued == 2)
reg_write32(hcd->regs, HC_INTERRUPT_ENABLE,
INTERRUPT_ENABLE_SOT_MASK);
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
buffstatus = reg_read32(hcd->regs,
HC_BUFFER_STATUS_REG);
buffstatus |= ATL_BUFFER;
reg_write32(hcd->regs, HC_BUFFER_STATUS_REG,
buffstatus);
continue;
}
error = check_error(&ptd);
if (error) {
status = error;
priv->atl_ints[queue_entry].qh->toggle = 0;
priv->atl_ints[queue_entry].qh->ping = 0;
urb->status = -EPIPE;
#if 0
printk(KERN_ERR "Error in %s().\n", __func__);
printk(KERN_ERR "IN dw0: %08x dw1: %08x dw2: %08x "
"dw3: %08x dw4: %08x dw5: %08x dw6: "
"%08x dw7: %08x\n",
ptd.dw0, ptd.dw1, ptd.dw2, ptd.dw3,
ptd.dw4, ptd.dw5, ptd.dw6, ptd.dw7);
#endif
} else {
if (usb_pipetype(urb->pipe) == PIPE_BULK) {
priv->atl_ints[queue_entry].qh->toggle =
ptd.dw3 & (1 << 25);
priv->atl_ints[queue_entry].qh->ping =
ptd.dw3 & (1 << 26);
}
}
length = PTD_XFERRED_LENGTH(ptd.dw3);
if (length) {
switch (DW1_GET_PID(ptd.dw1)) {
case IN_PID:
mem_reads8(hcd->regs, payload,
priv->atl_ints[queue_entry].data_buffer,
length);
case OUT_PID:
urb->actual_length += length;
case SETUP_PID:
break;
}
}
priv->atl_ints[queue_entry].data_buffer = NULL;
priv->atl_ints[queue_entry].urb = NULL;
priv->atl_ints[queue_entry].qtd = NULL;
priv->atl_ints[queue_entry].qh = NULL;
free_mem(priv, payload);
reg_write32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG, skip_map);
if (urb->status == -EPIPE) {
/* HALT was received */
qtd = clean_up_qtdlist(qtd);
isp1760_urb_done(priv, urb, urb->status);
} else if (usb_pipebulk(urb->pipe) && (length < qtd->length)) {
/* short BULK received */
if (urb->transfer_flags & URB_SHORT_NOT_OK) {
urb->status = -EREMOTEIO;
isp1760_dbg(priv, "short bulk, %d instead %zu "
"with URB_SHORT_NOT_OK flag.\n",
length, qtd->length);
}
if (urb->status == -EINPROGRESS)
urb->status = 0;
qtd = clean_up_qtdlist(qtd);
isp1760_urb_done(priv, urb, urb->status);
} else if (qtd->status & URB_COMPLETE_NOTIFY) {
/* that was the last qtd of that URB */
if (urb->status == -EINPROGRESS)
urb->status = 0;
qtd = clean_this_qtd(qtd);
isp1760_urb_done(priv, urb, urb->status);
} else {
/* next QTD of this URB */
qtd = clean_this_qtd(qtd);
BUG_ON(!qtd);
}
if (qtd)
enqueue_an_ATL_packet(hcd, qh, qtd);
skip_map = reg_read32(hcd->regs, HC_ATL_PTD_SKIPMAP_REG);
}
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
if (priv->atl_queued <= 1)
reg_write32(hcd->regs, HC_INTERRUPT_ENABLE,
INTERRUPT_ENABLE_MASK);
}
static void do_intl_int(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 done_map, skip_map;
struct ptd ptd;
struct urb *urb = NULL;
u32 payload;
u32 length;
u32 or_map;
int error;
u32 queue_entry;
struct isp1760_qtd *qtd;
struct isp1760_qh *qh;
done_map = reg_read32(hcd->regs, HC_INT_PTD_DONEMAP_REG);
skip_map = reg_read32(hcd->regs, HC_INT_PTD_SKIPMAP_REG);
or_map = reg_read32(hcd->regs, HC_INT_IRQ_MASK_OR_REG);
or_map &= ~done_map;
reg_write32(hcd->regs, HC_INT_IRQ_MASK_OR_REG, or_map);
while (done_map) {
queue_entry = __ffs(done_map);
done_map &= ~(1 << queue_entry);
skip_map |= 1 << queue_entry;
urb = priv->int_ints[queue_entry].urb;
qtd = priv->int_ints[queue_entry].qtd;
qh = priv->int_ints[queue_entry].qh;
payload = priv->int_ints[queue_entry].payload;
if (!qh) {
printk(KERN_ERR "(INT) qh is 0\n");
continue;
}
ptd_read(hcd->regs, INT_PTD_OFFSET, queue_entry, &ptd);
check_int_err_status(ptd.dw4);
error = check_error(&ptd);
if (error) {
#if 0
printk(KERN_ERR "Error in %s().\n", __func__);
printk(KERN_ERR "IN dw0: %08x dw1: %08x dw2: %08x "
"dw3: %08x dw4: %08x dw5: %08x dw6: "
"%08x dw7: %08x\n",
ptd.dw0, ptd.dw1, ptd.dw2, ptd.dw3,
ptd.dw4, ptd.dw5, ptd.dw6, ptd.dw7);
#endif
urb->status = -EPIPE;
priv->int_ints[queue_entry].qh->toggle = 0;
priv->int_ints[queue_entry].qh->ping = 0;
} else {
priv->int_ints[queue_entry].qh->toggle =
ptd.dw3 & (1 << 25);
priv->int_ints[queue_entry].qh->ping =
ptd.dw3 & (1 << 26);
}
if (urb->dev->speed != USB_SPEED_HIGH)
length = PTD_XFERRED_LENGTH_LO(ptd.dw3);
else
length = PTD_XFERRED_LENGTH(ptd.dw3);
if (length) {
switch (DW1_GET_PID(ptd.dw1)) {
case IN_PID:
mem_reads8(hcd->regs, payload,
priv->int_ints[queue_entry].data_buffer,
length);
case OUT_PID:
urb->actual_length += length;
case SETUP_PID:
break;
}
}
priv->int_ints[queue_entry].data_buffer = NULL;
priv->int_ints[queue_entry].urb = NULL;
priv->int_ints[queue_entry].qtd = NULL;
priv->int_ints[queue_entry].qh = NULL;
reg_write32(hcd->regs, HC_INT_PTD_SKIPMAP_REG, skip_map);
free_mem(priv, payload);
if (urb->status == -EPIPE) {
/* HALT received */
qtd = clean_up_qtdlist(qtd);
isp1760_urb_done(priv, urb, urb->status);
} else if (qtd->status & URB_COMPLETE_NOTIFY) {
if (urb->status == -EINPROGRESS)
urb->status = 0;
qtd = clean_this_qtd(qtd);
isp1760_urb_done(priv, urb, urb->status);
} else {
/* next QTD of this URB */
qtd = clean_this_qtd(qtd);
BUG_ON(!qtd);
}
if (qtd)
enqueue_an_INT_packet(hcd, qh, qtd);
skip_map = reg_read32(hcd->regs, HC_INT_PTD_SKIPMAP_REG);
}
}
#define max_packet(wMaxPacketSize) ((wMaxPacketSize) & 0x07ff)
static struct isp1760_qh *qh_make(struct isp1760_hcd *priv, struct urb *urb,
gfp_t flags)
{
struct isp1760_qh *qh;
int is_input, type;
qh = isp1760_qh_alloc(priv, flags);
if (!qh)
return qh;
/*
* init endpoint/device data for this QH
*/
is_input = usb_pipein(urb->pipe);
type = usb_pipetype(urb->pipe);
if (type == PIPE_INTERRUPT) {
if (urb->dev->speed == USB_SPEED_HIGH) {
qh->period = urb->interval >> 3;
if (qh->period == 0 && urb->interval != 1) {
/* NOTE interval 2 or 4 uframes could work.
* But interval 1 scheduling is simpler, and
* includes high bandwidth.
*/
printk(KERN_ERR "intr period %d uframes, NYET!",
urb->interval);
qh_destroy(qh);
return NULL;
}
} else {
qh->period = urb->interval;
}
}
/* support for tt scheduling, and access to toggles */
qh->dev = urb->dev;
if (!usb_pipecontrol(urb->pipe))
usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe), !is_input,
1);
return qh;
}
/*
* For control/bulk/interrupt, return QH with these TDs appended.
* Allocates and initializes the QH if necessary.
* Returns null if it can't allocate a QH it needs to.
* If the QH has TDs (urbs) already, that's great.
*/
static struct isp1760_qh *qh_append_tds(struct isp1760_hcd *priv,
struct urb *urb, struct list_head *qtd_list, int epnum,
void **ptr)
{
struct isp1760_qh *qh;
struct isp1760_qtd *qtd;
struct isp1760_qtd *prev_qtd;
qh = (struct isp1760_qh *)*ptr;
if (!qh) {
/* can't sleep here, we have priv->lock... */
qh = qh_make(priv, urb, GFP_ATOMIC);
if (!qh)
return qh;
*ptr = qh;
}
qtd = list_entry(qtd_list->next, struct isp1760_qtd,
qtd_list);
if (!list_empty(&qh->qtd_list))
prev_qtd = list_entry(qh->qtd_list.prev,
struct isp1760_qtd, qtd_list);
else
prev_qtd = NULL;
list_splice(qtd_list, qh->qtd_list.prev);
if (prev_qtd) {
BUG_ON(prev_qtd->hw_next);
prev_qtd->hw_next = qtd;
}
urb->hcpriv = qh;
return qh;
}
static void qtd_list_free(struct isp1760_hcd *priv, struct urb *urb,
struct list_head *qtd_list)
{
struct list_head *entry, *temp;
list_for_each_safe(entry, temp, qtd_list) {
struct isp1760_qtd *qtd;
qtd = list_entry(entry, struct isp1760_qtd, qtd_list);
list_del(&qtd->qtd_list);
isp1760_qtd_free(qtd);
}
}
static int isp1760_prepare_enqueue(struct isp1760_hcd *priv, struct urb *urb,
struct list_head *qtd_list, gfp_t mem_flags, packet_enqueue *p)
{
struct isp1760_qtd *qtd;
int epnum;
unsigned long flags;
struct isp1760_qh *qh = NULL;
int rc;
int qh_busy;
qtd = list_entry(qtd_list->next, struct isp1760_qtd, qtd_list);
epnum = urb->ep->desc.bEndpointAddress;
spin_lock_irqsave(&priv->lock, flags);
if (!HCD_HW_ACCESSIBLE(priv_to_hcd(priv))) {
rc = -ESHUTDOWN;
goto done;
}
rc = usb_hcd_link_urb_to_ep(priv_to_hcd(priv), urb);
if (rc)
goto done;
qh = urb->ep->hcpriv;
if (qh)
qh_busy = !list_empty(&qh->qtd_list);
else
qh_busy = 0;
qh = qh_append_tds(priv, urb, qtd_list, epnum, &urb->ep->hcpriv);
if (!qh) {
usb_hcd_unlink_urb_from_ep(priv_to_hcd(priv), urb);
rc = -ENOMEM;
goto done;
}
if (!qh_busy)
p(priv_to_hcd(priv), qh, qtd);
done:
spin_unlock_irqrestore(&priv->lock, flags);
if (!qh)
qtd_list_free(priv, urb, qtd_list);
return rc;
}
static struct isp1760_qtd *isp1760_qtd_alloc(struct isp1760_hcd *priv,
gfp_t flags)
{
struct isp1760_qtd *qtd;
qtd = kmem_cache_zalloc(qtd_cachep, flags);
if (qtd)
INIT_LIST_HEAD(&qtd->qtd_list);
return qtd;
}
/*
* create a list of filled qtds for this URB; won't link into qh.
*/
static struct list_head *qh_urb_transaction(struct isp1760_hcd *priv,
struct urb *urb, struct list_head *head, gfp_t flags)
{
struct isp1760_qtd *qtd, *qtd_prev;
void *buf;
int len, maxpacket;
int is_input;
u32 token;
/*
* URBs map to sequences of QTDs: one logical transaction
*/
qtd = isp1760_qtd_alloc(priv, flags);
if (!qtd)
return NULL;
list_add_tail(&qtd->qtd_list, head);
qtd->urb = urb;
urb->status = -EINPROGRESS;
token = 0;
/* for split transactions, SplitXState initialized to zero */
len = urb->transfer_buffer_length;
is_input = usb_pipein(urb->pipe);
if (usb_pipecontrol(urb->pipe)) {
/* SETUP pid */
qtd_fill(qtd, urb->setup_packet,
sizeof(struct usb_ctrlrequest),
token | SETUP_PID);
/* ... and always at least one more pid */
token ^= DATA_TOGGLE;
qtd_prev = qtd;
qtd = isp1760_qtd_alloc(priv, flags);
if (!qtd)
goto cleanup;
qtd->urb = urb;
qtd_prev->hw_next = qtd;
list_add_tail(&qtd->qtd_list, head);
/* for zero length DATA stages, STATUS is always IN */
if (len == 0)
token |= IN_PID;
}
/*
* data transfer stage: buffer setup
*/
buf = urb->transfer_buffer;
if (is_input)
token |= IN_PID;
else
token |= OUT_PID;
maxpacket = max_packet(usb_maxpacket(urb->dev, urb->pipe, !is_input));
/*
* buffer gets wrapped in one or more qtds;
* last one may be "short" (including zero len)
* and may serve as a control status ack
*/
for (;;) {
int this_qtd_len;
if (!buf && len) {
/* XXX This looks like usb storage / SCSI bug */
printk(KERN_ERR "buf is null, dma is %08lx len is %d\n",
(long unsigned)urb->transfer_dma, len);
WARN_ON(1);
}
this_qtd_len = qtd_fill(qtd, buf, len, token);
len -= this_qtd_len;
buf += this_qtd_len;
/* qh makes control packets use qtd toggle; maybe switch it */
if ((maxpacket & (this_qtd_len + (maxpacket - 1))) == 0)
token ^= DATA_TOGGLE;
if (len <= 0)
break;
qtd_prev = qtd;
qtd = isp1760_qtd_alloc(priv, flags);
if (!qtd)
goto cleanup;
qtd->urb = urb;
qtd_prev->hw_next = qtd;
list_add_tail(&qtd->qtd_list, head);
}
/*
* control requests may need a terminating data "status" ack;
* bulk ones may need a terminating short packet (zero length).
*/
if (urb->transfer_buffer_length != 0) {
int one_more = 0;
if (usb_pipecontrol(urb->pipe)) {
one_more = 1;
/* "in" <--> "out" */
token ^= IN_PID;
/* force DATA1 */
token |= DATA_TOGGLE;
} else if (usb_pipebulk(urb->pipe)
&& (urb->transfer_flags & URB_ZERO_PACKET)
&& !(urb->transfer_buffer_length % maxpacket)) {
one_more = 1;
}
if (one_more) {
qtd_prev = qtd;
qtd = isp1760_qtd_alloc(priv, flags);
if (!qtd)
goto cleanup;
qtd->urb = urb;
qtd_prev->hw_next = qtd;
list_add_tail(&qtd->qtd_list, head);
/* never any data in such packets */
qtd_fill(qtd, NULL, 0, token);
}
}
qtd->status = URB_COMPLETE_NOTIFY;
return head;
cleanup:
qtd_list_free(priv, urb, head);
return NULL;
}
static int isp1760_urb_enqueue(struct usb_hcd *hcd, struct urb *urb,
gfp_t mem_flags)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
struct list_head qtd_list;
packet_enqueue *pe;
INIT_LIST_HEAD(&qtd_list);
switch (usb_pipetype(urb->pipe)) {
case PIPE_CONTROL:
case PIPE_BULK:
if (!qh_urb_transaction(priv, urb, &qtd_list, mem_flags))
return -ENOMEM;
pe = enqueue_an_ATL_packet;
break;
case PIPE_INTERRUPT:
if (!qh_urb_transaction(priv, urb, &qtd_list, mem_flags))
return -ENOMEM;
pe = enqueue_an_INT_packet;
break;
case PIPE_ISOCHRONOUS:
printk(KERN_ERR "PIPE_ISOCHRONOUS ain't supported\n");
default:
return -EPIPE;
}
return isp1760_prepare_enqueue(priv, urb, &qtd_list, mem_flags, pe);
}
static int isp1760_urb_dequeue(struct usb_hcd *hcd, struct urb *urb,
int status)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
struct inter_packet_info *ints;
u32 i;
u32 reg_base, or_reg, skip_reg;
unsigned long flags;
struct ptd ptd;
packet_enqueue *pe;
switch (usb_pipetype(urb->pipe)) {
case PIPE_ISOCHRONOUS:
return -EPIPE;
break;
case PIPE_INTERRUPT:
ints = priv->int_ints;
reg_base = INT_PTD_OFFSET;
or_reg = HC_INT_IRQ_MASK_OR_REG;
skip_reg = HC_INT_PTD_SKIPMAP_REG;
pe = enqueue_an_INT_packet;
break;
default:
ints = priv->atl_ints;
reg_base = ATL_PTD_OFFSET;
or_reg = HC_ATL_IRQ_MASK_OR_REG;
skip_reg = HC_ATL_PTD_SKIPMAP_REG;
pe = enqueue_an_ATL_packet;
break;
}
memset(&ptd, 0, sizeof(ptd));
spin_lock_irqsave(&priv->lock, flags);
for (i = 0; i < 32; i++) {
if (ints->urb == urb) {
u32 skip_map;
u32 or_map;
struct isp1760_qtd *qtd;
struct isp1760_qh *qh = ints->qh;
skip_map = reg_read32(hcd->regs, skip_reg);
skip_map |= 1 << i;
reg_write32(hcd->regs, skip_reg, skip_map);
or_map = reg_read32(hcd->regs, or_reg);
or_map &= ~(1 << i);
reg_write32(hcd->regs, or_reg, or_map);
ptd_write(hcd->regs, reg_base, i, &ptd);
qtd = ints->qtd;
qtd = clean_up_qtdlist(qtd);
free_mem(priv, ints->payload);
ints->urb = NULL;
ints->qh = NULL;
ints->qtd = NULL;
ints->data_buffer = NULL;
ints->payload = 0;
isp1760_urb_done(priv, urb, status);
if (qtd)
pe(hcd, qh, qtd);
break;
} else if (ints->qtd) {
struct isp1760_qtd *qtd, *prev_qtd = ints->qtd;
for (qtd = ints->qtd->hw_next; qtd; qtd = qtd->hw_next) {
if (qtd->urb == urb) {
prev_qtd->hw_next =
clean_up_qtdlist(qtd);
isp1760_urb_done(priv, urb, status);
break;
}
prev_qtd = qtd;
}
/* we found the urb before the end of the list */
if (qtd)
break;
}
ints++;
}
spin_unlock_irqrestore(&priv->lock, flags);
return 0;
}
static irqreturn_t isp1760_irq(struct usb_hcd *usb_hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(usb_hcd);
u32 imask;
irqreturn_t irqret = IRQ_NONE;
spin_lock(&priv->lock);
if (!(usb_hcd->state & HC_STATE_RUNNING))
goto leave;
imask = reg_read32(usb_hcd->regs, HC_INTERRUPT_REG);
if (unlikely(!imask))
goto leave;
reg_write32(usb_hcd->regs, HC_INTERRUPT_REG, imask);
USB: isp1760: Implement solution for erratum 2 The document says: |2.1 Problem description | When at least two USB devices are simultaneously running, it is observed that | sometimes the INT corresponding to one of the USB devices stops occurring. This may | be observed sometimes with USB-to-serial or USB-to-network devices. | The problem is not noticed when only USB mass storage devices are running. |2.2 Implication | This issue is because of the clearing of the respective Done Map bit on reading the ATL | PTD Done Map register when an INT is generated by another PTD completion, but is not | found set on that read access. In this situation, the respective Done Map bit will remain | reset and no further INT will be asserted so the data transfer corresponding to that USB | device will stop. |2.3 Workaround | An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can | be implemented and if a certain Done bit is never set, verification of the PTD completion | can be done by reading PTD contents (valid bit). | This is a proven workaround implemented in software. Russell King run into this with an USB-to-serial converter. This patch implements his suggestion to enable the high frequent SOF interrupt only at the time we have ATL packages queued. It goes even one step further and enables the SOF interrupt only if we have more than one ATL packet queued at the same time. Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x] Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-09 04:07:40 +08:00
if (imask & (HC_ATL_INT | HC_SOT_INT))
do_atl_int(usb_hcd);
if (imask & HC_INTL_INT)
do_intl_int(usb_hcd);
irqret = IRQ_HANDLED;
leave:
spin_unlock(&priv->lock);
return irqret;
}
static int isp1760_hub_status_data(struct usb_hcd *hcd, char *buf)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 temp, status = 0;
u32 mask;
int retval = 1;
unsigned long flags;
/* if !USB_SUSPEND, root hub timers won't get shut down ... */
if (!HC_IS_RUNNING(hcd->state))
return 0;
/* init status to no-changes */
buf[0] = 0;
mask = PORT_CSC;
spin_lock_irqsave(&priv->lock, flags);
temp = reg_read32(hcd->regs, HC_PORTSC1);
if (temp & PORT_OWNER) {
if (temp & PORT_CSC) {
temp &= ~PORT_CSC;
reg_write32(hcd->regs, HC_PORTSC1, temp);
goto done;
}
}
/*
* Return status information even for ports with OWNER set.
* Otherwise khubd wouldn't see the disconnect event when a
* high-speed device is switched over to the companion
* controller by the user.
*/
if ((temp & mask) != 0
|| ((temp & PORT_RESUME) != 0
&& time_after_eq(jiffies,
priv->reset_done))) {
buf [0] |= 1 << (0 + 1);
status = STS_PCD;
}
/* FIXME autosuspend idle root hubs */
done:
spin_unlock_irqrestore(&priv->lock, flags);
return status ? retval : 0;
}
static void isp1760_hub_descriptor(struct isp1760_hcd *priv,
struct usb_hub_descriptor *desc)
{
int ports = HCS_N_PORTS(priv->hcs_params);
u16 temp;
desc->bDescriptorType = 0x29;
/* priv 1.0, 2.3.9 says 20ms max */
desc->bPwrOn2PwrGood = 10;
desc->bHubContrCurrent = 0;
desc->bNbrPorts = ports;
temp = 1 + (ports / 8);
desc->bDescLength = 7 + 2 * temp;
/* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */
memset(&desc->bitmap[0], 0, temp);
memset(&desc->bitmap[temp], 0xff, temp);
/* per-port overcurrent reporting */
temp = 0x0008;
if (HCS_PPC(priv->hcs_params))
/* per-port power control */
temp |= 0x0001;
else
/* no power switching */
temp |= 0x0002;
desc->wHubCharacteristics = cpu_to_le16(temp);
}
#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
static int check_reset_complete(struct usb_hcd *hcd, int index,
int port_status)
{
if (!(port_status & PORT_CONNECT))
return port_status;
/* if reset finished and it's still not enabled -- handoff */
if (!(port_status & PORT_PE)) {
printk(KERN_ERR "port %d full speed --> companion\n",
index + 1);
port_status |= PORT_OWNER;
port_status &= ~PORT_RWC_BITS;
reg_write32(hcd->regs, HC_PORTSC1, port_status);
} else
printk(KERN_ERR "port %d high speed\n", index + 1);
return port_status;
}
static int isp1760_hub_control(struct usb_hcd *hcd, u16 typeReq,
u16 wValue, u16 wIndex, char *buf, u16 wLength)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
int ports = HCS_N_PORTS(priv->hcs_params);
u32 temp, status;
unsigned long flags;
int retval = 0;
unsigned selector;
/*
* FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR.
* HCS_INDICATOR may say we can change LEDs to off/amber/green.
* (track current state ourselves) ... blink for diagnostics,
* power, "this is the one", etc. EHCI spec supports this.
*/
spin_lock_irqsave(&priv->lock, flags);
switch (typeReq) {
case ClearHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case ClearPortFeature:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = reg_read32(hcd->regs, HC_PORTSC1);
/*
* Even if OWNER is set, so the port is owned by the
* companion controller, khubd needs to be able to clear
* the port-change status bits (especially
* USB_PORT_STAT_C_CONNECTION).
*/
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
reg_write32(hcd->regs, HC_PORTSC1, temp & ~PORT_PE);
break;
case USB_PORT_FEAT_C_ENABLE:
/* XXX error? */
break;
case USB_PORT_FEAT_SUSPEND:
if (temp & PORT_RESET)
goto error;
if (temp & PORT_SUSPEND) {
if ((temp & PORT_PE) == 0)
goto error;
/* resume signaling for 20 msec */
temp &= ~(PORT_RWC_BITS);
reg_write32(hcd->regs, HC_PORTSC1,
temp | PORT_RESUME);
priv->reset_done = jiffies +
msecs_to_jiffies(20);
}
break;
case USB_PORT_FEAT_C_SUSPEND:
/* we auto-clear this feature */
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC(priv->hcs_params))
reg_write32(hcd->regs, HC_PORTSC1,
temp & ~PORT_POWER);
break;
case USB_PORT_FEAT_C_CONNECTION:
reg_write32(hcd->regs, HC_PORTSC1, temp | PORT_CSC);
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
/* XXX error ?*/
break;
case USB_PORT_FEAT_C_RESET:
/* GetPortStatus clears reset */
break;
default:
goto error;
}
reg_read32(hcd->regs, HC_USBCMD);
break;
case GetHubDescriptor:
isp1760_hub_descriptor(priv, (struct usb_hub_descriptor *)
buf);
break;
case GetHubStatus:
/* no hub-wide feature/status flags */
memset(buf, 0, 4);
break;
case GetPortStatus:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
status = 0;
temp = reg_read32(hcd->regs, HC_PORTSC1);
/* wPortChange bits */
if (temp & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
/* whoever resumes must GetPortStatus to complete it!! */
if (temp & PORT_RESUME) {
printk(KERN_ERR "Port resume should be skipped.\n");
/* Remote Wakeup received? */
if (!priv->reset_done) {
/* resume signaling for 20 msec */
priv->reset_done = jiffies
+ msecs_to_jiffies(20);
/* check the port again */
mod_timer(&priv_to_hcd(priv)->rh_timer,
priv->reset_done);
}
/* resume completed? */
else if (time_after_eq(jiffies,
priv->reset_done)) {
status |= USB_PORT_STAT_C_SUSPEND << 16;
priv->reset_done = 0;
/* stop resume signaling */
temp = reg_read32(hcd->regs, HC_PORTSC1);
reg_write32(hcd->regs, HC_PORTSC1,
temp & ~(PORT_RWC_BITS | PORT_RESUME));
retval = handshake(hcd, HC_PORTSC1,
PORT_RESUME, 0, 2000 /* 2msec */);
if (retval != 0) {
isp1760_err(priv,
"port %d resume error %d\n",
wIndex + 1, retval);
goto error;
}
temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
}
}
/* whoever resets must GetPortStatus to complete it!! */
if ((temp & PORT_RESET)
&& time_after_eq(jiffies,
priv->reset_done)) {
status |= USB_PORT_STAT_C_RESET << 16;
priv->reset_done = 0;
/* force reset to complete */
reg_write32(hcd->regs, HC_PORTSC1, temp & ~PORT_RESET);
/* REVISIT: some hardware needs 550+ usec to clear
* this bit; seems too long to spin routinely...
*/
retval = handshake(hcd, HC_PORTSC1,
PORT_RESET, 0, 750);
if (retval != 0) {
isp1760_err(priv, "port %d reset error %d\n",
wIndex + 1, retval);
goto error;
}
/* see what we found out */
temp = check_reset_complete(hcd, wIndex,
reg_read32(hcd->regs, HC_PORTSC1));
}
/*
* Even if OWNER is set, there's no harm letting khubd
* see the wPortStatus values (they should all be 0 except
* for PORT_POWER anyway).
*/
if (temp & PORT_OWNER)
printk(KERN_ERR "Warning: PORT_OWNER is set\n");
if (temp & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
/* status may be from integrated TT */
status |= ehci_port_speed(priv, temp);
}
if (temp & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
if (temp & (PORT_SUSPEND|PORT_RESUME))
status |= USB_PORT_STAT_SUSPEND;
if (temp & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (temp & PORT_POWER)
status |= USB_PORT_STAT_POWER;
put_unaligned(cpu_to_le32(status), (__le32 *) buf);
break;
case SetHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case SetPortFeature:
selector = wIndex >> 8;
wIndex &= 0xff;
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = reg_read32(hcd->regs, HC_PORTSC1);
if (temp & PORT_OWNER)
break;
/* temp &= ~PORT_RWC_BITS; */
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
reg_write32(hcd->regs, HC_PORTSC1, temp | PORT_PE);
break;
case USB_PORT_FEAT_SUSPEND:
if ((temp & PORT_PE) == 0
|| (temp & PORT_RESET) != 0)
goto error;
reg_write32(hcd->regs, HC_PORTSC1, temp | PORT_SUSPEND);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC(priv->hcs_params))
reg_write32(hcd->regs, HC_PORTSC1,
temp | PORT_POWER);
break;
case USB_PORT_FEAT_RESET:
if (temp & PORT_RESUME)
goto error;
/* line status bits may report this as low speed,
* which can be fine if this root hub has a
* transaction translator built in.
*/
if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
&& PORT_USB11(temp)) {
temp |= PORT_OWNER;
} else {
temp |= PORT_RESET;
temp &= ~PORT_PE;
/*
* caller must wait, then call GetPortStatus
* usb 2.0 spec says 50 ms resets on root
*/
priv->reset_done = jiffies +
msecs_to_jiffies(50);
}
reg_write32(hcd->regs, HC_PORTSC1, temp);
break;
default:
goto error;
}
reg_read32(hcd->regs, HC_USBCMD);
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
spin_unlock_irqrestore(&priv->lock, flags);
return retval;
}
static void isp1760_endpoint_disable(struct usb_hcd *usb_hcd,
struct usb_host_endpoint *ep)
{
struct isp1760_hcd *priv = hcd_to_priv(usb_hcd);
struct isp1760_qh *qh;
struct isp1760_qtd *qtd;
unsigned long flags;
spin_lock_irqsave(&priv->lock, flags);
qh = ep->hcpriv;
if (!qh)
goto out;
ep->hcpriv = NULL;
do {
/* more than entry might get removed */
if (list_empty(&qh->qtd_list))
break;
qtd = list_first_entry(&qh->qtd_list, struct isp1760_qtd,
qtd_list);
if (qtd->status & URB_ENQUEUED) {
spin_unlock_irqrestore(&priv->lock, flags);
isp1760_urb_dequeue(usb_hcd, qtd->urb, -ECONNRESET);
spin_lock_irqsave(&priv->lock, flags);
} else {
struct urb *urb;
urb = qtd->urb;
clean_up_qtdlist(qtd);
isp1760_urb_done(priv, urb, -ECONNRESET);
}
} while (1);
qh_destroy(qh);
/* remove requests and leak them.
* ATL are pretty fast done, INT could take a while...
* The latter shoule be removed
*/
out:
spin_unlock_irqrestore(&priv->lock, flags);
}
static int isp1760_get_frame(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 fr;
fr = reg_read32(hcd->regs, HC_FRINDEX);
return (fr >> 3) % priv->periodic_size;
}
static void isp1760_stop(struct usb_hcd *hcd)
{
struct isp1760_hcd *priv = hcd_to_priv(hcd);
u32 temp;
isp1760_hub_control(hcd, ClearPortFeature, USB_PORT_FEAT_POWER, 1,
NULL, 0);
mdelay(20);
spin_lock_irq(&priv->lock);
ehci_reset(priv);
/* Disable IRQ */
temp = reg_read32(hcd->regs, HC_HW_MODE_CTRL);
reg_write32(hcd->regs, HC_HW_MODE_CTRL, temp &= ~HW_GLOBAL_INTR_EN);
spin_unlock_irq(&priv->lock);
reg_write32(hcd->regs, HC_CONFIGFLAG, 0);
}
static void isp1760_shutdown(struct usb_hcd *hcd)
{
u32 command, temp;
isp1760_stop(hcd);
temp = reg_read32(hcd->regs, HC_HW_MODE_CTRL);
reg_write32(hcd->regs, HC_HW_MODE_CTRL, temp &= ~HW_GLOBAL_INTR_EN);
command = reg_read32(hcd->regs, HC_USBCMD);
command &= ~CMD_RUN;
reg_write32(hcd->regs, HC_USBCMD, command);
}
static const struct hc_driver isp1760_hc_driver = {
.description = "isp1760-hcd",
.product_desc = "NXP ISP1760 USB Host Controller",
.hcd_priv_size = sizeof(struct isp1760_hcd),
.irq = isp1760_irq,
.flags = HCD_MEMORY | HCD_USB2,
.reset = isp1760_hc_setup,
.start = isp1760_run,
.stop = isp1760_stop,
.shutdown = isp1760_shutdown,
.urb_enqueue = isp1760_urb_enqueue,
.urb_dequeue = isp1760_urb_dequeue,
.endpoint_disable = isp1760_endpoint_disable,
.get_frame_number = isp1760_get_frame,
.hub_status_data = isp1760_hub_status_data,
.hub_control = isp1760_hub_control,
};
int __init init_kmem_once(void)
{
qtd_cachep = kmem_cache_create("isp1760_qtd",
sizeof(struct isp1760_qtd), 0, SLAB_TEMPORARY |
SLAB_MEM_SPREAD, NULL);
if (!qtd_cachep)
return -ENOMEM;
qh_cachep = kmem_cache_create("isp1760_qh", sizeof(struct isp1760_qh),
0, SLAB_TEMPORARY | SLAB_MEM_SPREAD, NULL);
if (!qh_cachep) {
kmem_cache_destroy(qtd_cachep);
return -ENOMEM;
}
return 0;
}
void deinit_kmem_cache(void)
{
kmem_cache_destroy(qtd_cachep);
kmem_cache_destroy(qh_cachep);
}
struct usb_hcd *isp1760_register(phys_addr_t res_start, resource_size_t res_len,
int irq, unsigned long irqflags,
struct device *dev, const char *busname,
unsigned int devflags)
{
struct usb_hcd *hcd;
struct isp1760_hcd *priv;
int ret;
if (usb_disabled())
return ERR_PTR(-ENODEV);
/* prevent usb-core allocating DMA pages */
dev->dma_mask = NULL;
hcd = usb_create_hcd(&isp1760_hc_driver, dev, dev_name(dev));
if (!hcd)
return ERR_PTR(-ENOMEM);
priv = hcd_to_priv(hcd);
priv->devflags = devflags;
init_memory(priv);
hcd->regs = ioremap(res_start, res_len);
if (!hcd->regs) {
ret = -EIO;
goto err_put;
}
hcd->irq = irq;
hcd->rsrc_start = res_start;
hcd->rsrc_len = res_len;
ret = usb_add_hcd(hcd, irq, irqflags);
if (ret)
goto err_unmap;
return hcd;
err_unmap:
iounmap(hcd->regs);
err_put:
usb_put_hcd(hcd);
return ERR_PTR(ret);
}
MODULE_DESCRIPTION("Driver for the ISP1760 USB-controller from NXP");
MODULE_AUTHOR("Sebastian Siewior <bigeasy@linuxtronix.de>");
MODULE_LICENSE("GPL v2");