linux-sg2042/drivers/hid/hid-logitech-hidpp.c

3823 lines
107 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* HIDPP protocol for Logitech Unifying receivers
*
* Copyright (c) 2011 Logitech (c)
* Copyright (c) 2012-2013 Google (c)
* Copyright (c) 2013-2014 Red Hat Inc.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/device.h>
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
#include <linux/input.h>
#include <linux/usb.h>
#include <linux/hid.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/sched.h>
#include <linux/sched/clock.h>
#include <linux/kfifo.h>
#include <linux/input/mt.h>
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
#include <linux/workqueue.h>
#include <linux/atomic.h>
#include <linux/fixp-arith.h>
#include <asm/unaligned.h>
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
#include "usbhid/usbhid.h"
#include "hid-ids.h"
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>");
MODULE_AUTHOR("Nestor Lopez Casado <nlopezcasad@logitech.com>");
static bool disable_raw_mode;
module_param(disable_raw_mode, bool, 0644);
MODULE_PARM_DESC(disable_raw_mode,
"Disable Raw mode reporting for touchpads and keep firmware gestures.");
static bool disable_tap_to_click;
module_param(disable_tap_to_click, bool, 0644);
MODULE_PARM_DESC(disable_tap_to_click,
"Disable Tap-To-Click mode reporting for touchpads (only on the K400 currently).");
#define REPORT_ID_HIDPP_SHORT 0x10
#define REPORT_ID_HIDPP_LONG 0x11
#define REPORT_ID_HIDPP_VERY_LONG 0x12
#define HIDPP_REPORT_SHORT_LENGTH 7
#define HIDPP_REPORT_LONG_LENGTH 20
#define HIDPP_REPORT_VERY_LONG_MAX_LENGTH 64
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
#define HIDPP_SUB_ID_CONSUMER_VENDOR_KEYS 0x03
#define HIDPP_SUB_ID_ROLLER 0x05
#define HIDPP_SUB_ID_MOUSE_EXTRA_BTNS 0x06
#define HIDPP_QUIRK_CLASS_WTP BIT(0)
#define HIDPP_QUIRK_CLASS_M560 BIT(1)
#define HIDPP_QUIRK_CLASS_K400 BIT(2)
#define HIDPP_QUIRK_CLASS_G920 BIT(3)
#define HIDPP_QUIRK_CLASS_K750 BIT(4)
/* bits 2..20 are reserved for classes */
/* #define HIDPP_QUIRK_CONNECT_EVENTS BIT(21) disabled */
#define HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS BIT(22)
#define HIDPP_QUIRK_NO_HIDINPUT BIT(23)
#define HIDPP_QUIRK_FORCE_OUTPUT_REPORTS BIT(24)
#define HIDPP_QUIRK_UNIFYING BIT(25)
#define HIDPP_QUIRK_HI_RES_SCROLL_1P0 BIT(26)
#define HIDPP_QUIRK_HI_RES_SCROLL_X2120 BIT(27)
#define HIDPP_QUIRK_HI_RES_SCROLL_X2121 BIT(28)
#define HIDPP_QUIRK_HIDPP_WHEELS BIT(29)
#define HIDPP_QUIRK_HIDPP_EXTRA_MOUSE_BTNS BIT(30)
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
#define HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS BIT(31)
/* These are just aliases for now */
#define HIDPP_QUIRK_KBD_SCROLL_WHEEL HIDPP_QUIRK_HIDPP_WHEELS
#define HIDPP_QUIRK_KBD_ZOOM_WHEEL HIDPP_QUIRK_HIDPP_WHEELS
/* Convenience constant to check for any high-res support. */
#define HIDPP_QUIRK_HI_RES_SCROLL (HIDPP_QUIRK_HI_RES_SCROLL_1P0 | \
HIDPP_QUIRK_HI_RES_SCROLL_X2120 | \
HIDPP_QUIRK_HI_RES_SCROLL_X2121)
#define HIDPP_QUIRK_DELAYED_INIT HIDPP_QUIRK_NO_HIDINPUT
#define HIDPP_CAPABILITY_HIDPP10_BATTERY BIT(0)
#define HIDPP_CAPABILITY_HIDPP20_BATTERY BIT(1)
#define HIDPP_CAPABILITY_BATTERY_MILEAGE BIT(2)
#define HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS BIT(3)
/*
* There are two hidpp protocols in use, the first version hidpp10 is known
* as register access protocol or RAP, the second version hidpp20 is known as
* feature access protocol or FAP
*
* Most older devices (including the Unifying usb receiver) use the RAP protocol
* where as most newer devices use the FAP protocol. Both protocols are
* compatible with the underlying transport, which could be usb, Unifiying, or
* bluetooth. The message lengths are defined by the hid vendor specific report
* descriptor for the HIDPP_SHORT report type (total message lenth 7 bytes) and
* the HIDPP_LONG report type (total message length 20 bytes)
*
* The RAP protocol uses both report types, whereas the FAP only uses HIDPP_LONG
* messages. The Unifying receiver itself responds to RAP messages (device index
* is 0xFF for the receiver), and all messages (short or long) with a device
* index between 1 and 6 are passed untouched to the corresponding paired
* Unifying device.
*
* The paired device can be RAP or FAP, it will receive the message untouched
* from the Unifiying receiver.
*/
struct fap {
u8 feature_index;
u8 funcindex_clientid;
u8 params[HIDPP_REPORT_VERY_LONG_MAX_LENGTH - 4U];
};
struct rap {
u8 sub_id;
u8 reg_address;
u8 params[HIDPP_REPORT_VERY_LONG_MAX_LENGTH - 4U];
};
struct hidpp_report {
u8 report_id;
u8 device_index;
union {
struct fap fap;
struct rap rap;
u8 rawbytes[sizeof(struct fap)];
};
} __packed;
struct hidpp_battery {
u8 feature_index;
u8 solar_feature_index;
struct power_supply_desc desc;
struct power_supply *ps;
char name[64];
int status;
int capacity;
int level;
bool online;
};
/**
* struct hidpp_scroll_counter - Utility class for processing high-resolution
* scroll events.
* @dev: the input device for which events should be reported.
* @wheel_multiplier: the scalar multiplier to be applied to each wheel event
* @remainder: counts the number of high-resolution units moved since the last
* low-resolution event (REL_WHEEL or REL_HWHEEL) was sent. Should
* only be used by class methods.
* @direction: direction of last movement (1 or -1)
* @last_time: last event time, used to reset remainder after inactivity
*/
struct hidpp_scroll_counter {
int wheel_multiplier;
int remainder;
int direction;
unsigned long long last_time;
};
struct hidpp_device {
struct hid_device *hid_dev;
struct input_dev *input;
struct mutex send_mutex;
void *send_receive_buf;
char *name; /* will never be NULL and should not be freed */
wait_queue_head_t wait;
int very_long_report_length;
bool answer_available;
u8 protocol_major;
u8 protocol_minor;
void *private_data;
struct work_struct work;
struct kfifo delayed_work_fifo;
atomic_t connected;
struct input_dev *delayed_input;
unsigned long quirks;
unsigned long capabilities;
struct hidpp_battery battery;
struct hidpp_scroll_counter vertical_wheel_counter;
};
/* HID++ 1.0 error codes */
#define HIDPP_ERROR 0x8f
#define HIDPP_ERROR_SUCCESS 0x00
#define HIDPP_ERROR_INVALID_SUBID 0x01
#define HIDPP_ERROR_INVALID_ADRESS 0x02
#define HIDPP_ERROR_INVALID_VALUE 0x03
#define HIDPP_ERROR_CONNECT_FAIL 0x04
#define HIDPP_ERROR_TOO_MANY_DEVICES 0x05
#define HIDPP_ERROR_ALREADY_EXISTS 0x06
#define HIDPP_ERROR_BUSY 0x07
#define HIDPP_ERROR_UNKNOWN_DEVICE 0x08
#define HIDPP_ERROR_RESOURCE_ERROR 0x09
#define HIDPP_ERROR_REQUEST_UNAVAILABLE 0x0a
#define HIDPP_ERROR_INVALID_PARAM_VALUE 0x0b
#define HIDPP_ERROR_WRONG_PIN_CODE 0x0c
/* HID++ 2.0 error codes */
#define HIDPP20_ERROR 0xff
static void hidpp_connect_event(struct hidpp_device *hidpp_dev);
static int __hidpp_send_report(struct hid_device *hdev,
struct hidpp_report *hidpp_report)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
int fields_count, ret;
switch (hidpp_report->report_id) {
case REPORT_ID_HIDPP_SHORT:
fields_count = HIDPP_REPORT_SHORT_LENGTH;
break;
case REPORT_ID_HIDPP_LONG:
fields_count = HIDPP_REPORT_LONG_LENGTH;
break;
case REPORT_ID_HIDPP_VERY_LONG:
fields_count = hidpp->very_long_report_length;
break;
default:
return -ENODEV;
}
/*
* set the device_index as the receiver, it will be overwritten by
* hid_hw_request if needed
*/
hidpp_report->device_index = 0xff;
if (hidpp->quirks & HIDPP_QUIRK_FORCE_OUTPUT_REPORTS) {
ret = hid_hw_output_report(hdev, (u8 *)hidpp_report, fields_count);
} else {
ret = hid_hw_raw_request(hdev, hidpp_report->report_id,
(u8 *)hidpp_report, fields_count, HID_OUTPUT_REPORT,
HID_REQ_SET_REPORT);
}
return ret == fields_count ? 0 : -1;
}
/**
* hidpp_send_message_sync() returns 0 in case of success, and something else
* in case of a failure.
* - If ' something else' is positive, that means that an error has been raised
* by the protocol itself.
* - If ' something else' is negative, that means that we had a classic error
* (-ENOMEM, -EPIPE, etc...)
*/
static int hidpp_send_message_sync(struct hidpp_device *hidpp,
struct hidpp_report *message,
struct hidpp_report *response)
{
int ret;
mutex_lock(&hidpp->send_mutex);
hidpp->send_receive_buf = response;
hidpp->answer_available = false;
/*
* So that we can later validate the answer when it arrives
* in hidpp_raw_event
*/
*response = *message;
ret = __hidpp_send_report(hidpp->hid_dev, message);
if (ret) {
dbg_hid("__hidpp_send_report returned err: %d\n", ret);
memset(response, 0, sizeof(struct hidpp_report));
goto exit;
}
if (!wait_event_timeout(hidpp->wait, hidpp->answer_available,
5*HZ)) {
dbg_hid("%s:timeout waiting for response\n", __func__);
memset(response, 0, sizeof(struct hidpp_report));
ret = -ETIMEDOUT;
}
if (response->report_id == REPORT_ID_HIDPP_SHORT &&
response->rap.sub_id == HIDPP_ERROR) {
ret = response->rap.params[1];
dbg_hid("%s:got hidpp error %02X\n", __func__, ret);
goto exit;
}
if ((response->report_id == REPORT_ID_HIDPP_LONG ||
response->report_id == REPORT_ID_HIDPP_VERY_LONG) &&
response->fap.feature_index == HIDPP20_ERROR) {
ret = response->fap.params[1];
dbg_hid("%s:got hidpp 2.0 error %02X\n", __func__, ret);
goto exit;
}
exit:
mutex_unlock(&hidpp->send_mutex);
return ret;
}
static int hidpp_send_fap_command_sync(struct hidpp_device *hidpp,
u8 feat_index, u8 funcindex_clientid, u8 *params, int param_count,
struct hidpp_report *response)
{
struct hidpp_report *message;
int ret;
if (param_count > sizeof(message->fap.params))
return -EINVAL;
message = kzalloc(sizeof(struct hidpp_report), GFP_KERNEL);
if (!message)
return -ENOMEM;
if (param_count > (HIDPP_REPORT_LONG_LENGTH - 4))
message->report_id = REPORT_ID_HIDPP_VERY_LONG;
else
message->report_id = REPORT_ID_HIDPP_LONG;
message->fap.feature_index = feat_index;
message->fap.funcindex_clientid = funcindex_clientid;
memcpy(&message->fap.params, params, param_count);
ret = hidpp_send_message_sync(hidpp, message, response);
kfree(message);
return ret;
}
static int hidpp_send_rap_command_sync(struct hidpp_device *hidpp_dev,
u8 report_id, u8 sub_id, u8 reg_address, u8 *params, int param_count,
struct hidpp_report *response)
{
struct hidpp_report *message;
int ret, max_count;
switch (report_id) {
case REPORT_ID_HIDPP_SHORT:
max_count = HIDPP_REPORT_SHORT_LENGTH - 4;
break;
case REPORT_ID_HIDPP_LONG:
max_count = HIDPP_REPORT_LONG_LENGTH - 4;
break;
case REPORT_ID_HIDPP_VERY_LONG:
max_count = hidpp_dev->very_long_report_length - 4;
break;
default:
return -EINVAL;
}
if (param_count > max_count)
return -EINVAL;
message = kzalloc(sizeof(struct hidpp_report), GFP_KERNEL);
if (!message)
return -ENOMEM;
message->report_id = report_id;
message->rap.sub_id = sub_id;
message->rap.reg_address = reg_address;
memcpy(&message->rap.params, params, param_count);
ret = hidpp_send_message_sync(hidpp_dev, message, response);
kfree(message);
return ret;
}
static void delayed_work_cb(struct work_struct *work)
{
struct hidpp_device *hidpp = container_of(work, struct hidpp_device,
work);
hidpp_connect_event(hidpp);
}
static inline bool hidpp_match_answer(struct hidpp_report *question,
struct hidpp_report *answer)
{
return (answer->fap.feature_index == question->fap.feature_index) &&
(answer->fap.funcindex_clientid == question->fap.funcindex_clientid);
}
static inline bool hidpp_match_error(struct hidpp_report *question,
struct hidpp_report *answer)
{
return ((answer->rap.sub_id == HIDPP_ERROR) ||
(answer->fap.feature_index == HIDPP20_ERROR)) &&
(answer->fap.funcindex_clientid == question->fap.feature_index) &&
(answer->fap.params[0] == question->fap.funcindex_clientid);
}
static inline bool hidpp_report_is_connect_event(struct hidpp_report *report)
{
return (report->report_id == REPORT_ID_HIDPP_SHORT) &&
(report->rap.sub_id == 0x41);
}
/**
* hidpp_prefix_name() prefixes the current given name with "Logitech ".
*/
static void hidpp_prefix_name(char **name, int name_length)
{
#define PREFIX_LENGTH 9 /* "Logitech " */
int new_length;
char *new_name;
if (name_length > PREFIX_LENGTH &&
strncmp(*name, "Logitech ", PREFIX_LENGTH) == 0)
/* The prefix has is already in the name */
return;
new_length = PREFIX_LENGTH + name_length;
new_name = kzalloc(new_length, GFP_KERNEL);
if (!new_name)
return;
snprintf(new_name, new_length, "Logitech %s", *name);
kfree(*name);
*name = new_name;
}
/**
* hidpp_scroll_counter_handle_scroll() - Send high- and low-resolution scroll
* events given a high-resolution wheel
* movement.
* @counter: a hid_scroll_counter struct describing the wheel.
* @hi_res_value: the movement of the wheel, in the mouse's high-resolution
* units.
*
* Given a high-resolution movement, this function converts the movement into
* fractions of 120 and emits high-resolution scroll events for the input
* device. It also uses the multiplier from &struct hid_scroll_counter to
* emit low-resolution scroll events when appropriate for
* backwards-compatibility with userspace input libraries.
*/
static void hidpp_scroll_counter_handle_scroll(struct input_dev *input_dev,
struct hidpp_scroll_counter *counter,
int hi_res_value)
{
int low_res_value, remainder, direction;
unsigned long long now, previous;
hi_res_value = hi_res_value * 120/counter->wheel_multiplier;
input_report_rel(input_dev, REL_WHEEL_HI_RES, hi_res_value);
remainder = counter->remainder;
direction = hi_res_value > 0 ? 1 : -1;
now = sched_clock();
previous = counter->last_time;
counter->last_time = now;
/*
* Reset the remainder after a period of inactivity or when the
* direction changes. This prevents the REL_WHEEL emulation point
* from sliding for devices that don't always provide the same
* number of movements per detent.
*/
if (now - previous > 1000000000 || direction != counter->direction)
remainder = 0;
counter->direction = direction;
remainder += hi_res_value;
/* Some wheels will rest 7/8ths of a detent from the previous detent
* after slow movement, so we want the threshold for low-res events to
* be in the middle between two detents (e.g. after 4/8ths) as
* opposed to on the detents themselves (8/8ths).
*/
if (abs(remainder) >= 60) {
/* Add (or subtract) 1 because we want to trigger when the wheel
* is half-way to the next detent (i.e. scroll 1 detent after a
* 1/2 detent movement, 2 detents after a 1 1/2 detent movement,
* etc.).
*/
low_res_value = remainder / 120;
if (low_res_value == 0)
low_res_value = (hi_res_value > 0 ? 1 : -1);
input_report_rel(input_dev, REL_WHEEL, low_res_value);
remainder -= low_res_value * 120;
}
counter->remainder = remainder;
}
/* -------------------------------------------------------------------------- */
/* HIDP++ 1.0 commands */
/* -------------------------------------------------------------------------- */
#define HIDPP_SET_REGISTER 0x80
#define HIDPP_GET_REGISTER 0x81
#define HIDPP_SET_LONG_REGISTER 0x82
#define HIDPP_GET_LONG_REGISTER 0x83
/**
* hidpp10_set_register - Modify a HID++ 1.0 register.
* @hidpp_dev: the device to set the register on.
* @register_address: the address of the register to modify.
* @byte: the byte of the register to modify. Should be less than 3.
* @mask: mask of the bits to modify
* @value: new values for the bits in mask
* Return: 0 if successful, otherwise a negative error code.
*/
static int hidpp10_set_register(struct hidpp_device *hidpp_dev,
u8 register_address, u8 byte, u8 mask, u8 value)
{
struct hidpp_report response;
int ret;
u8 params[3] = { 0 };
ret = hidpp_send_rap_command_sync(hidpp_dev,
REPORT_ID_HIDPP_SHORT,
HIDPP_GET_REGISTER,
register_address,
NULL, 0, &response);
if (ret)
return ret;
memcpy(params, response.rap.params, 3);
params[byte] &= ~mask;
params[byte] |= value & mask;
return hidpp_send_rap_command_sync(hidpp_dev,
REPORT_ID_HIDPP_SHORT,
HIDPP_SET_REGISTER,
register_address,
params, 3, &response);
}
#define HIDPP_REG_ENABLE_REPORTS 0x00
#define HIDPP_ENABLE_CONSUMER_REPORT BIT(0)
#define HIDPP_ENABLE_WHEEL_REPORT BIT(2)
#define HIDPP_ENABLE_MOUSE_EXTRA_BTN_REPORT BIT(3)
#define HIDPP_ENABLE_BAT_REPORT BIT(4)
#define HIDPP_ENABLE_HWHEEL_REPORT BIT(5)
static int hidpp10_enable_battery_reporting(struct hidpp_device *hidpp_dev)
{
return hidpp10_set_register(hidpp_dev, HIDPP_REG_ENABLE_REPORTS, 0,
HIDPP_ENABLE_BAT_REPORT, HIDPP_ENABLE_BAT_REPORT);
}
#define HIDPP_REG_FEATURES 0x01
#define HIDPP_ENABLE_SPECIAL_BUTTON_FUNC BIT(1)
#define HIDPP_ENABLE_FAST_SCROLL BIT(6)
/* On HID++ 1.0 devices, high-res scroll was called "scrolling acceleration". */
static int hidpp10_enable_scrolling_acceleration(struct hidpp_device *hidpp_dev)
{
return hidpp10_set_register(hidpp_dev, HIDPP_REG_FEATURES, 0,
HIDPP_ENABLE_FAST_SCROLL, HIDPP_ENABLE_FAST_SCROLL);
}
#define HIDPP_REG_BATTERY_STATUS 0x07
static int hidpp10_battery_status_map_level(u8 param)
{
int level;
switch (param) {
case 1 ... 2:
level = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
break;
case 3 ... 4:
level = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
break;
case 5 ... 6:
level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
break;
case 7:
level = POWER_SUPPLY_CAPACITY_LEVEL_HIGH;
break;
default:
level = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN;
}
return level;
}
static int hidpp10_battery_status_map_status(u8 param)
{
int status;
switch (param) {
case 0x00:
/* discharging (in use) */
status = POWER_SUPPLY_STATUS_DISCHARGING;
break;
case 0x21: /* (standard) charging */
case 0x24: /* fast charging */
case 0x25: /* slow charging */
status = POWER_SUPPLY_STATUS_CHARGING;
break;
case 0x26: /* topping charge */
case 0x22: /* charge complete */
status = POWER_SUPPLY_STATUS_FULL;
break;
case 0x20: /* unknown */
status = POWER_SUPPLY_STATUS_UNKNOWN;
break;
/*
* 0x01...0x1F = reserved (not charging)
* 0x23 = charging error
* 0x27..0xff = reserved
*/
default:
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
break;
}
return status;
}
static int hidpp10_query_battery_status(struct hidpp_device *hidpp)
{
struct hidpp_report response;
int ret, status;
ret = hidpp_send_rap_command_sync(hidpp,
REPORT_ID_HIDPP_SHORT,
HIDPP_GET_REGISTER,
HIDPP_REG_BATTERY_STATUS,
NULL, 0, &response);
if (ret)
return ret;
hidpp->battery.level =
hidpp10_battery_status_map_level(response.rap.params[0]);
status = hidpp10_battery_status_map_status(response.rap.params[1]);
hidpp->battery.status = status;
/* the capacity is only available when discharging or full */
hidpp->battery.online = status == POWER_SUPPLY_STATUS_DISCHARGING ||
status == POWER_SUPPLY_STATUS_FULL;
return 0;
}
#define HIDPP_REG_BATTERY_MILEAGE 0x0D
static int hidpp10_battery_mileage_map_status(u8 param)
{
int status;
switch (param >> 6) {
case 0x00:
/* discharging (in use) */
status = POWER_SUPPLY_STATUS_DISCHARGING;
break;
case 0x01: /* charging */
status = POWER_SUPPLY_STATUS_CHARGING;
break;
case 0x02: /* charge complete */
status = POWER_SUPPLY_STATUS_FULL;
break;
/*
* 0x03 = charging error
*/
default:
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
break;
}
return status;
}
static int hidpp10_query_battery_mileage(struct hidpp_device *hidpp)
{
struct hidpp_report response;
int ret, status;
ret = hidpp_send_rap_command_sync(hidpp,
REPORT_ID_HIDPP_SHORT,
HIDPP_GET_REGISTER,
HIDPP_REG_BATTERY_MILEAGE,
NULL, 0, &response);
if (ret)
return ret;
hidpp->battery.capacity = response.rap.params[0];
status = hidpp10_battery_mileage_map_status(response.rap.params[2]);
hidpp->battery.status = status;
/* the capacity is only available when discharging or full */
hidpp->battery.online = status == POWER_SUPPLY_STATUS_DISCHARGING ||
status == POWER_SUPPLY_STATUS_FULL;
return 0;
}
static int hidpp10_battery_event(struct hidpp_device *hidpp, u8 *data, int size)
{
struct hidpp_report *report = (struct hidpp_report *)data;
int status, capacity, level;
bool changed;
if (report->report_id != REPORT_ID_HIDPP_SHORT)
return 0;
switch (report->rap.sub_id) {
case HIDPP_REG_BATTERY_STATUS:
capacity = hidpp->battery.capacity;
level = hidpp10_battery_status_map_level(report->rawbytes[1]);
status = hidpp10_battery_status_map_status(report->rawbytes[2]);
break;
case HIDPP_REG_BATTERY_MILEAGE:
capacity = report->rap.params[0];
level = hidpp->battery.level;
status = hidpp10_battery_mileage_map_status(report->rawbytes[3]);
break;
default:
return 0;
}
changed = capacity != hidpp->battery.capacity ||
level != hidpp->battery.level ||
status != hidpp->battery.status;
/* the capacity is only available when discharging or full */
hidpp->battery.online = status == POWER_SUPPLY_STATUS_DISCHARGING ||
status == POWER_SUPPLY_STATUS_FULL;
if (changed) {
hidpp->battery.level = level;
hidpp->battery.status = status;
if (hidpp->battery.ps)
power_supply_changed(hidpp->battery.ps);
}
return 0;
}
#define HIDPP_REG_PAIRING_INFORMATION 0xB5
#define HIDPP_EXTENDED_PAIRING 0x30
#define HIDPP_DEVICE_NAME 0x40
static char *hidpp_unifying_get_name(struct hidpp_device *hidpp_dev)
{
struct hidpp_report response;
int ret;
u8 params[1] = { HIDPP_DEVICE_NAME };
char *name;
int len;
ret = hidpp_send_rap_command_sync(hidpp_dev,
REPORT_ID_HIDPP_SHORT,
HIDPP_GET_LONG_REGISTER,
HIDPP_REG_PAIRING_INFORMATION,
params, 1, &response);
if (ret)
return NULL;
len = response.rap.params[1];
if (2 + len > sizeof(response.rap.params))
return NULL;
if (len < 4) /* logitech devices are usually at least Xddd */
return NULL;
name = kzalloc(len + 1, GFP_KERNEL);
if (!name)
return NULL;
memcpy(name, &response.rap.params[2], len);
/* include the terminating '\0' */
hidpp_prefix_name(&name, len + 1);
return name;
}
static int hidpp_unifying_get_serial(struct hidpp_device *hidpp, u32 *serial)
{
struct hidpp_report response;
int ret;
u8 params[1] = { HIDPP_EXTENDED_PAIRING };
ret = hidpp_send_rap_command_sync(hidpp,
REPORT_ID_HIDPP_SHORT,
HIDPP_GET_LONG_REGISTER,
HIDPP_REG_PAIRING_INFORMATION,
params, 1, &response);
if (ret)
return ret;
/*
* We don't care about LE or BE, we will output it as a string
* with %4phD, so we need to keep the order.
*/
*serial = *((u32 *)&response.rap.params[1]);
return 0;
}
static int hidpp_unifying_init(struct hidpp_device *hidpp)
{
struct hid_device *hdev = hidpp->hid_dev;
const char *name;
u32 serial;
int ret;
ret = hidpp_unifying_get_serial(hidpp, &serial);
if (ret)
return ret;
snprintf(hdev->uniq, sizeof(hdev->uniq), "%04x-%4phD",
hdev->product, &serial);
dbg_hid("HID++ Unifying: Got serial: %s\n", hdev->uniq);
name = hidpp_unifying_get_name(hidpp);
if (!name)
return -EIO;
snprintf(hdev->name, sizeof(hdev->name), "%s", name);
dbg_hid("HID++ Unifying: Got name: %s\n", name);
kfree(name);
return 0;
}
/* -------------------------------------------------------------------------- */
/* 0x0000: Root */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_ROOT 0x0000
#define HIDPP_PAGE_ROOT_IDX 0x00
#define CMD_ROOT_GET_FEATURE 0x01
#define CMD_ROOT_GET_PROTOCOL_VERSION 0x11
static int hidpp_root_get_feature(struct hidpp_device *hidpp, u16 feature,
u8 *feature_index, u8 *feature_type)
{
struct hidpp_report response;
int ret;
u8 params[2] = { feature >> 8, feature & 0x00FF };
ret = hidpp_send_fap_command_sync(hidpp,
HIDPP_PAGE_ROOT_IDX,
CMD_ROOT_GET_FEATURE,
params, 2, &response);
if (ret)
return ret;
if (response.fap.params[0] == 0)
return -ENOENT;
*feature_index = response.fap.params[0];
*feature_type = response.fap.params[1];
return ret;
}
static int hidpp_root_get_protocol_version(struct hidpp_device *hidpp)
{
const u8 ping_byte = 0x5a;
u8 ping_data[3] = { 0, 0, ping_byte };
struct hidpp_report response;
int ret;
ret = hidpp_send_rap_command_sync(hidpp,
REPORT_ID_HIDPP_SHORT,
HIDPP_PAGE_ROOT_IDX,
CMD_ROOT_GET_PROTOCOL_VERSION,
ping_data, sizeof(ping_data), &response);
if (ret == HIDPP_ERROR_INVALID_SUBID) {
hidpp->protocol_major = 1;
hidpp->protocol_minor = 0;
goto print_version;
}
/* the device might not be connected */
if (ret == HIDPP_ERROR_RESOURCE_ERROR)
return -EIO;
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
if (response.rap.params[2] != ping_byte) {
hid_err(hidpp->hid_dev, "%s: ping mismatch 0x%02x != 0x%02x\n",
__func__, response.rap.params[2], ping_byte);
return -EPROTO;
}
hidpp->protocol_major = response.rap.params[0];
hidpp->protocol_minor = response.rap.params[1];
print_version:
hid_info(hidpp->hid_dev, "HID++ %u.%u device connected.\n",
hidpp->protocol_major, hidpp->protocol_minor);
return 0;
}
/* -------------------------------------------------------------------------- */
/* 0x0005: GetDeviceNameType */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_GET_DEVICE_NAME_TYPE 0x0005
#define CMD_GET_DEVICE_NAME_TYPE_GET_COUNT 0x01
#define CMD_GET_DEVICE_NAME_TYPE_GET_DEVICE_NAME 0x11
#define CMD_GET_DEVICE_NAME_TYPE_GET_TYPE 0x21
static int hidpp_devicenametype_get_count(struct hidpp_device *hidpp,
u8 feature_index, u8 *nameLength)
{
struct hidpp_report response;
int ret;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_GET_DEVICE_NAME_TYPE_GET_COUNT, NULL, 0, &response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
*nameLength = response.fap.params[0];
return ret;
}
static int hidpp_devicenametype_get_device_name(struct hidpp_device *hidpp,
u8 feature_index, u8 char_index, char *device_name, int len_buf)
{
struct hidpp_report response;
int ret, i;
int count;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_GET_DEVICE_NAME_TYPE_GET_DEVICE_NAME, &char_index, 1,
&response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
switch (response.report_id) {
case REPORT_ID_HIDPP_VERY_LONG:
count = hidpp->very_long_report_length - 4;
break;
case REPORT_ID_HIDPP_LONG:
count = HIDPP_REPORT_LONG_LENGTH - 4;
break;
case REPORT_ID_HIDPP_SHORT:
count = HIDPP_REPORT_SHORT_LENGTH - 4;
break;
default:
return -EPROTO;
}
if (len_buf < count)
count = len_buf;
for (i = 0; i < count; i++)
device_name[i] = response.fap.params[i];
return count;
}
static char *hidpp_get_device_name(struct hidpp_device *hidpp)
{
u8 feature_type;
u8 feature_index;
u8 __name_length;
char *name;
unsigned index = 0;
int ret;
ret = hidpp_root_get_feature(hidpp, HIDPP_PAGE_GET_DEVICE_NAME_TYPE,
&feature_index, &feature_type);
if (ret)
return NULL;
ret = hidpp_devicenametype_get_count(hidpp, feature_index,
&__name_length);
if (ret)
return NULL;
name = kzalloc(__name_length + 1, GFP_KERNEL);
if (!name)
return NULL;
while (index < __name_length) {
ret = hidpp_devicenametype_get_device_name(hidpp,
feature_index, index, name + index,
__name_length - index);
if (ret <= 0) {
kfree(name);
return NULL;
}
index += ret;
}
/* include the terminating '\0' */
hidpp_prefix_name(&name, __name_length + 1);
return name;
}
/* -------------------------------------------------------------------------- */
/* 0x1000: Battery level status */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_BATTERY_LEVEL_STATUS 0x1000
#define CMD_BATTERY_LEVEL_STATUS_GET_BATTERY_LEVEL_STATUS 0x00
#define CMD_BATTERY_LEVEL_STATUS_GET_BATTERY_CAPABILITY 0x10
#define EVENT_BATTERY_LEVEL_STATUS_BROADCAST 0x00
#define FLAG_BATTERY_LEVEL_DISABLE_OSD BIT(0)
#define FLAG_BATTERY_LEVEL_MILEAGE BIT(1)
#define FLAG_BATTERY_LEVEL_RECHARGEABLE BIT(2)
static int hidpp_map_battery_level(int capacity)
{
if (capacity < 11)
return POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
/*
* The spec says this should be < 31 but some devices report 30
* with brand new batteries and Windows reports 30 as "Good".
*/
else if (capacity < 30)
return POWER_SUPPLY_CAPACITY_LEVEL_LOW;
else if (capacity < 81)
return POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
return POWER_SUPPLY_CAPACITY_LEVEL_FULL;
}
static int hidpp20_batterylevel_map_status_capacity(u8 data[3], int *capacity,
int *next_capacity,
int *level)
{
int status;
*capacity = data[0];
*next_capacity = data[1];
*level = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN;
/* When discharging, we can rely on the device reported capacity.
* For all other states the device reports 0 (unknown).
*/
switch (data[2]) {
case 0: /* discharging (in use) */
status = POWER_SUPPLY_STATUS_DISCHARGING;
*level = hidpp_map_battery_level(*capacity);
break;
case 1: /* recharging */
status = POWER_SUPPLY_STATUS_CHARGING;
break;
case 2: /* charge in final stage */
status = POWER_SUPPLY_STATUS_CHARGING;
break;
case 3: /* charge complete */
status = POWER_SUPPLY_STATUS_FULL;
*level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
*capacity = 100;
break;
case 4: /* recharging below optimal speed */
status = POWER_SUPPLY_STATUS_CHARGING;
break;
/* 5 = invalid battery type
6 = thermal error
7 = other charging error */
default:
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
break;
}
return status;
}
static int hidpp20_batterylevel_get_battery_capacity(struct hidpp_device *hidpp,
u8 feature_index,
int *status,
int *capacity,
int *next_capacity,
int *level)
{
struct hidpp_report response;
int ret;
u8 *params = (u8 *)response.fap.params;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_BATTERY_LEVEL_STATUS_GET_BATTERY_LEVEL_STATUS,
NULL, 0, &response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
*status = hidpp20_batterylevel_map_status_capacity(params, capacity,
next_capacity,
level);
return 0;
}
static int hidpp20_batterylevel_get_battery_info(struct hidpp_device *hidpp,
u8 feature_index)
{
struct hidpp_report response;
int ret;
u8 *params = (u8 *)response.fap.params;
unsigned int level_count, flags;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_BATTERY_LEVEL_STATUS_GET_BATTERY_CAPABILITY,
NULL, 0, &response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
level_count = params[0];
flags = params[1];
if (level_count < 10 || !(flags & FLAG_BATTERY_LEVEL_MILEAGE))
hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS;
else
hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_MILEAGE;
return 0;
}
static int hidpp20_query_battery_info(struct hidpp_device *hidpp)
{
u8 feature_type;
int ret;
int status, capacity, next_capacity, level;
if (hidpp->battery.feature_index == 0xff) {
ret = hidpp_root_get_feature(hidpp,
HIDPP_PAGE_BATTERY_LEVEL_STATUS,
&hidpp->battery.feature_index,
&feature_type);
if (ret)
return ret;
}
ret = hidpp20_batterylevel_get_battery_capacity(hidpp,
hidpp->battery.feature_index,
&status, &capacity,
&next_capacity, &level);
if (ret)
return ret;
ret = hidpp20_batterylevel_get_battery_info(hidpp,
hidpp->battery.feature_index);
if (ret)
return ret;
hidpp->battery.status = status;
hidpp->battery.capacity = capacity;
hidpp->battery.level = level;
/* the capacity is only available when discharging or full */
hidpp->battery.online = status == POWER_SUPPLY_STATUS_DISCHARGING ||
status == POWER_SUPPLY_STATUS_FULL;
return 0;
}
static int hidpp20_battery_event(struct hidpp_device *hidpp,
u8 *data, int size)
{
struct hidpp_report *report = (struct hidpp_report *)data;
int status, capacity, next_capacity, level;
bool changed;
if (report->fap.feature_index != hidpp->battery.feature_index ||
report->fap.funcindex_clientid != EVENT_BATTERY_LEVEL_STATUS_BROADCAST)
return 0;
status = hidpp20_batterylevel_map_status_capacity(report->fap.params,
&capacity,
&next_capacity,
&level);
/* the capacity is only available when discharging or full */
hidpp->battery.online = status == POWER_SUPPLY_STATUS_DISCHARGING ||
status == POWER_SUPPLY_STATUS_FULL;
changed = capacity != hidpp->battery.capacity ||
level != hidpp->battery.level ||
status != hidpp->battery.status;
if (changed) {
hidpp->battery.level = level;
hidpp->battery.capacity = capacity;
hidpp->battery.status = status;
if (hidpp->battery.ps)
power_supply_changed(hidpp->battery.ps);
}
return 0;
}
static enum power_supply_property hidpp_battery_props[] = {
POWER_SUPPLY_PROP_ONLINE,
POWER_SUPPLY_PROP_STATUS,
POWER_SUPPLY_PROP_SCOPE,
POWER_SUPPLY_PROP_MODEL_NAME,
POWER_SUPPLY_PROP_MANUFACTURER,
POWER_SUPPLY_PROP_SERIAL_NUMBER,
0, /* placeholder for POWER_SUPPLY_PROP_CAPACITY, */
0, /* placeholder for POWER_SUPPLY_PROP_CAPACITY_LEVEL, */
};
static int hidpp_battery_get_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
{
struct hidpp_device *hidpp = power_supply_get_drvdata(psy);
int ret = 0;
switch(psp) {
case POWER_SUPPLY_PROP_STATUS:
val->intval = hidpp->battery.status;
break;
case POWER_SUPPLY_PROP_CAPACITY:
val->intval = hidpp->battery.capacity;
break;
case POWER_SUPPLY_PROP_CAPACITY_LEVEL:
val->intval = hidpp->battery.level;
break;
case POWER_SUPPLY_PROP_SCOPE:
val->intval = POWER_SUPPLY_SCOPE_DEVICE;
break;
case POWER_SUPPLY_PROP_ONLINE:
val->intval = hidpp->battery.online;
break;
case POWER_SUPPLY_PROP_MODEL_NAME:
if (!strncmp(hidpp->name, "Logitech ", 9))
val->strval = hidpp->name + 9;
else
val->strval = hidpp->name;
break;
case POWER_SUPPLY_PROP_MANUFACTURER:
val->strval = "Logitech";
break;
case POWER_SUPPLY_PROP_SERIAL_NUMBER:
val->strval = hidpp->hid_dev->uniq;
break;
default:
ret = -EINVAL;
break;
}
return ret;
}
/* -------------------------------------------------------------------------- */
/* 0x2120: Hi-resolution scrolling */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_HI_RESOLUTION_SCROLLING 0x2120
#define CMD_HI_RESOLUTION_SCROLLING_SET_HIGHRES_SCROLLING_MODE 0x10
static int hidpp_hrs_set_highres_scrolling_mode(struct hidpp_device *hidpp,
bool enabled, u8 *multiplier)
{
u8 feature_index;
u8 feature_type;
int ret;
u8 params[1];
struct hidpp_report response;
ret = hidpp_root_get_feature(hidpp,
HIDPP_PAGE_HI_RESOLUTION_SCROLLING,
&feature_index,
&feature_type);
if (ret)
return ret;
params[0] = enabled ? BIT(0) : 0;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_HI_RESOLUTION_SCROLLING_SET_HIGHRES_SCROLLING_MODE,
params, sizeof(params), &response);
if (ret)
return ret;
*multiplier = response.fap.params[1];
return 0;
}
/* -------------------------------------------------------------------------- */
/* 0x2121: HiRes Wheel */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_HIRES_WHEEL 0x2121
#define CMD_HIRES_WHEEL_GET_WHEEL_CAPABILITY 0x00
#define CMD_HIRES_WHEEL_SET_WHEEL_MODE 0x20
static int hidpp_hrw_get_wheel_capability(struct hidpp_device *hidpp,
u8 *multiplier)
{
u8 feature_index;
u8 feature_type;
int ret;
struct hidpp_report response;
ret = hidpp_root_get_feature(hidpp, HIDPP_PAGE_HIRES_WHEEL,
&feature_index, &feature_type);
if (ret)
goto return_default;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_HIRES_WHEEL_GET_WHEEL_CAPABILITY,
NULL, 0, &response);
if (ret)
goto return_default;
*multiplier = response.fap.params[0];
return 0;
return_default:
hid_warn(hidpp->hid_dev,
"Couldn't get wheel multiplier (error %d)\n", ret);
return ret;
}
static int hidpp_hrw_set_wheel_mode(struct hidpp_device *hidpp, bool invert,
bool high_resolution, bool use_hidpp)
{
u8 feature_index;
u8 feature_type;
int ret;
u8 params[1];
struct hidpp_report response;
ret = hidpp_root_get_feature(hidpp, HIDPP_PAGE_HIRES_WHEEL,
&feature_index, &feature_type);
if (ret)
return ret;
params[0] = (invert ? BIT(2) : 0) |
(high_resolution ? BIT(1) : 0) |
(use_hidpp ? BIT(0) : 0);
return hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_HIRES_WHEEL_SET_WHEEL_MODE,
params, sizeof(params), &response);
}
/* -------------------------------------------------------------------------- */
/* 0x4301: Solar Keyboard */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_SOLAR_KEYBOARD 0x4301
#define CMD_SOLAR_SET_LIGHT_MEASURE 0x00
#define EVENT_SOLAR_BATTERY_BROADCAST 0x00
#define EVENT_SOLAR_BATTERY_LIGHT_MEASURE 0x10
#define EVENT_SOLAR_CHECK_LIGHT_BUTTON 0x20
static int hidpp_solar_request_battery_event(struct hidpp_device *hidpp)
{
struct hidpp_report response;
u8 params[2] = { 1, 1 };
u8 feature_type;
int ret;
if (hidpp->battery.feature_index == 0xff) {
ret = hidpp_root_get_feature(hidpp,
HIDPP_PAGE_SOLAR_KEYBOARD,
&hidpp->battery.solar_feature_index,
&feature_type);
if (ret)
return ret;
}
ret = hidpp_send_fap_command_sync(hidpp,
hidpp->battery.solar_feature_index,
CMD_SOLAR_SET_LIGHT_MEASURE,
params, 2, &response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_MILEAGE;
return 0;
}
static int hidpp_solar_battery_event(struct hidpp_device *hidpp,
u8 *data, int size)
{
struct hidpp_report *report = (struct hidpp_report *)data;
int capacity, lux, status;
u8 function;
function = report->fap.funcindex_clientid;
if (report->fap.feature_index != hidpp->battery.solar_feature_index ||
!(function == EVENT_SOLAR_BATTERY_BROADCAST ||
function == EVENT_SOLAR_BATTERY_LIGHT_MEASURE ||
function == EVENT_SOLAR_CHECK_LIGHT_BUTTON))
return 0;
capacity = report->fap.params[0];
switch (function) {
case EVENT_SOLAR_BATTERY_LIGHT_MEASURE:
lux = (report->fap.params[1] << 8) | report->fap.params[2];
if (lux > 200)
status = POWER_SUPPLY_STATUS_CHARGING;
else
status = POWER_SUPPLY_STATUS_DISCHARGING;
break;
case EVENT_SOLAR_CHECK_LIGHT_BUTTON:
default:
if (capacity < hidpp->battery.capacity)
status = POWER_SUPPLY_STATUS_DISCHARGING;
else
status = POWER_SUPPLY_STATUS_CHARGING;
}
if (capacity == 100)
status = POWER_SUPPLY_STATUS_FULL;
hidpp->battery.online = true;
if (capacity != hidpp->battery.capacity ||
status != hidpp->battery.status) {
hidpp->battery.capacity = capacity;
hidpp->battery.status = status;
if (hidpp->battery.ps)
power_supply_changed(hidpp->battery.ps);
}
return 0;
}
/* -------------------------------------------------------------------------- */
/* 0x6010: Touchpad FW items */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_TOUCHPAD_FW_ITEMS 0x6010
#define CMD_TOUCHPAD_FW_ITEMS_SET 0x10
struct hidpp_touchpad_fw_items {
uint8_t presence;
uint8_t desired_state;
uint8_t state;
uint8_t persistent;
};
/**
* send a set state command to the device by reading the current items->state
* field. items is then filled with the current state.
*/
static int hidpp_touchpad_fw_items_set(struct hidpp_device *hidpp,
u8 feature_index,
struct hidpp_touchpad_fw_items *items)
{
struct hidpp_report response;
int ret;
u8 *params = (u8 *)response.fap.params;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_TOUCHPAD_FW_ITEMS_SET, &items->state, 1, &response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
items->presence = params[0];
items->desired_state = params[1];
items->state = params[2];
items->persistent = params[3];
return 0;
}
/* -------------------------------------------------------------------------- */
/* 0x6100: TouchPadRawXY */
/* -------------------------------------------------------------------------- */
#define HIDPP_PAGE_TOUCHPAD_RAW_XY 0x6100
#define CMD_TOUCHPAD_GET_RAW_INFO 0x01
#define CMD_TOUCHPAD_SET_RAW_REPORT_STATE 0x21
#define EVENT_TOUCHPAD_RAW_XY 0x00
#define TOUCHPAD_RAW_XY_ORIGIN_LOWER_LEFT 0x01
#define TOUCHPAD_RAW_XY_ORIGIN_UPPER_LEFT 0x03
struct hidpp_touchpad_raw_info {
u16 x_size;
u16 y_size;
u8 z_range;
u8 area_range;
u8 timestamp_unit;
u8 maxcontacts;
u8 origin;
u16 res;
};
struct hidpp_touchpad_raw_xy_finger {
u8 contact_type;
u8 contact_status;
u16 x;
u16 y;
u8 z;
u8 area;
u8 finger_id;
};
struct hidpp_touchpad_raw_xy {
u16 timestamp;
struct hidpp_touchpad_raw_xy_finger fingers[2];
u8 spurious_flag;
u8 end_of_frame;
u8 finger_count;
u8 button;
};
static int hidpp_touchpad_get_raw_info(struct hidpp_device *hidpp,
u8 feature_index, struct hidpp_touchpad_raw_info *raw_info)
{
struct hidpp_report response;
int ret;
u8 *params = (u8 *)response.fap.params;
ret = hidpp_send_fap_command_sync(hidpp, feature_index,
CMD_TOUCHPAD_GET_RAW_INFO, NULL, 0, &response);
if (ret > 0) {
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, ret);
return -EPROTO;
}
if (ret)
return ret;
raw_info->x_size = get_unaligned_be16(&params[0]);
raw_info->y_size = get_unaligned_be16(&params[2]);
raw_info->z_range = params[4];
raw_info->area_range = params[5];
raw_info->maxcontacts = params[7];
raw_info->origin = params[8];
/* res is given in unit per inch */
raw_info->res = get_unaligned_be16(&params[13]) * 2 / 51;
return ret;
}
static int hidpp_touchpad_set_raw_report_state(struct hidpp_device *hidpp_dev,
u8 feature_index, bool send_raw_reports,
bool sensor_enhanced_settings)
{
struct hidpp_report response;
/*
* Params:
* bit 0 - enable raw
* bit 1 - 16bit Z, no area
* bit 2 - enhanced sensitivity
* bit 3 - width, height (4 bits each) instead of area
* bit 4 - send raw + gestures (degrades smoothness)
* remaining bits - reserved
*/
u8 params = send_raw_reports | (sensor_enhanced_settings << 2);
return hidpp_send_fap_command_sync(hidpp_dev, feature_index,
CMD_TOUCHPAD_SET_RAW_REPORT_STATE, &params, 1, &response);
}
static void hidpp_touchpad_touch_event(u8 *data,
struct hidpp_touchpad_raw_xy_finger *finger)
{
u8 x_m = data[0] << 2;
u8 y_m = data[2] << 2;
finger->x = x_m << 6 | data[1];
finger->y = y_m << 6 | data[3];
finger->contact_type = data[0] >> 6;
finger->contact_status = data[2] >> 6;
finger->z = data[4];
finger->area = data[5];
finger->finger_id = data[6] >> 4;
}
static void hidpp_touchpad_raw_xy_event(struct hidpp_device *hidpp_dev,
u8 *data, struct hidpp_touchpad_raw_xy *raw_xy)
{
memset(raw_xy, 0, sizeof(struct hidpp_touchpad_raw_xy));
raw_xy->end_of_frame = data[8] & 0x01;
raw_xy->spurious_flag = (data[8] >> 1) & 0x01;
raw_xy->finger_count = data[15] & 0x0f;
raw_xy->button = (data[8] >> 2) & 0x01;
if (raw_xy->finger_count) {
hidpp_touchpad_touch_event(&data[2], &raw_xy->fingers[0]);
hidpp_touchpad_touch_event(&data[9], &raw_xy->fingers[1]);
}
}
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
/* -------------------------------------------------------------------------- */
/* 0x8123: Force feedback support */
/* -------------------------------------------------------------------------- */
#define HIDPP_FF_GET_INFO 0x01
#define HIDPP_FF_RESET_ALL 0x11
#define HIDPP_FF_DOWNLOAD_EFFECT 0x21
#define HIDPP_FF_SET_EFFECT_STATE 0x31
#define HIDPP_FF_DESTROY_EFFECT 0x41
#define HIDPP_FF_GET_APERTURE 0x51
#define HIDPP_FF_SET_APERTURE 0x61
#define HIDPP_FF_GET_GLOBAL_GAINS 0x71
#define HIDPP_FF_SET_GLOBAL_GAINS 0x81
#define HIDPP_FF_EFFECT_STATE_GET 0x00
#define HIDPP_FF_EFFECT_STATE_STOP 0x01
#define HIDPP_FF_EFFECT_STATE_PLAY 0x02
#define HIDPP_FF_EFFECT_STATE_PAUSE 0x03
#define HIDPP_FF_EFFECT_CONSTANT 0x00
#define HIDPP_FF_EFFECT_PERIODIC_SINE 0x01
#define HIDPP_FF_EFFECT_PERIODIC_SQUARE 0x02
#define HIDPP_FF_EFFECT_PERIODIC_TRIANGLE 0x03
#define HIDPP_FF_EFFECT_PERIODIC_SAWTOOTHUP 0x04
#define HIDPP_FF_EFFECT_PERIODIC_SAWTOOTHDOWN 0x05
#define HIDPP_FF_EFFECT_SPRING 0x06
#define HIDPP_FF_EFFECT_DAMPER 0x07
#define HIDPP_FF_EFFECT_FRICTION 0x08
#define HIDPP_FF_EFFECT_INERTIA 0x09
#define HIDPP_FF_EFFECT_RAMP 0x0A
#define HIDPP_FF_EFFECT_AUTOSTART 0x80
#define HIDPP_FF_EFFECTID_NONE -1
#define HIDPP_FF_EFFECTID_AUTOCENTER -2
#define HIDPP_FF_MAX_PARAMS 20
#define HIDPP_FF_RESERVED_SLOTS 1
struct hidpp_ff_private_data {
struct hidpp_device *hidpp;
u8 feature_index;
u8 version;
u16 gain;
s16 range;
u8 slot_autocenter;
u8 num_effects;
int *effect_ids;
struct workqueue_struct *wq;
atomic_t workqueue_size;
};
struct hidpp_ff_work_data {
struct work_struct work;
struct hidpp_ff_private_data *data;
int effect_id;
u8 command;
u8 params[HIDPP_FF_MAX_PARAMS];
u8 size;
};
static const signed short hidpp_ff_effects[] = {
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
FF_CONSTANT,
FF_PERIODIC,
FF_SINE,
FF_SQUARE,
FF_SAW_UP,
FF_SAW_DOWN,
FF_TRIANGLE,
FF_SPRING,
FF_DAMPER,
FF_AUTOCENTER,
FF_GAIN,
-1
};
static const signed short hidpp_ff_effects_v2[] = {
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
FF_RAMP,
FF_FRICTION,
FF_INERTIA,
-1
};
static const u8 HIDPP_FF_CONDITION_CMDS[] = {
HIDPP_FF_EFFECT_SPRING,
HIDPP_FF_EFFECT_FRICTION,
HIDPP_FF_EFFECT_DAMPER,
HIDPP_FF_EFFECT_INERTIA
};
static const char *HIDPP_FF_CONDITION_NAMES[] = {
"spring",
"friction",
"damper",
"inertia"
};
static u8 hidpp_ff_find_effect(struct hidpp_ff_private_data *data, int effect_id)
{
int i;
for (i = 0; i < data->num_effects; i++)
if (data->effect_ids[i] == effect_id)
return i+1;
return 0;
}
static void hidpp_ff_work_handler(struct work_struct *w)
{
struct hidpp_ff_work_data *wd = container_of(w, struct hidpp_ff_work_data, work);
struct hidpp_ff_private_data *data = wd->data;
struct hidpp_report response;
u8 slot;
int ret;
/* add slot number if needed */
switch (wd->effect_id) {
case HIDPP_FF_EFFECTID_AUTOCENTER:
wd->params[0] = data->slot_autocenter;
break;
case HIDPP_FF_EFFECTID_NONE:
/* leave slot as zero */
break;
default:
/* find current slot for effect */
wd->params[0] = hidpp_ff_find_effect(data, wd->effect_id);
break;
}
/* send command and wait for reply */
ret = hidpp_send_fap_command_sync(data->hidpp, data->feature_index,
wd->command, wd->params, wd->size, &response);
if (ret) {
hid_err(data->hidpp->hid_dev, "Failed to send command to device!\n");
goto out;
}
/* parse return data */
switch (wd->command) {
case HIDPP_FF_DOWNLOAD_EFFECT:
slot = response.fap.params[0];
if (slot > 0 && slot <= data->num_effects) {
if (wd->effect_id >= 0)
/* regular effect uploaded */
data->effect_ids[slot-1] = wd->effect_id;
else if (wd->effect_id >= HIDPP_FF_EFFECTID_AUTOCENTER)
/* autocenter spring uploaded */
data->slot_autocenter = slot;
}
break;
case HIDPP_FF_DESTROY_EFFECT:
if (wd->effect_id >= 0)
/* regular effect destroyed */
data->effect_ids[wd->params[0]-1] = -1;
else if (wd->effect_id >= HIDPP_FF_EFFECTID_AUTOCENTER)
/* autocenter spring destoyed */
data->slot_autocenter = 0;
break;
case HIDPP_FF_SET_GLOBAL_GAINS:
data->gain = (wd->params[0] << 8) + wd->params[1];
break;
case HIDPP_FF_SET_APERTURE:
data->range = (wd->params[0] << 8) + wd->params[1];
break;
default:
/* no action needed */
break;
}
out:
atomic_dec(&data->workqueue_size);
kfree(wd);
}
static int hidpp_ff_queue_work(struct hidpp_ff_private_data *data, int effect_id, u8 command, u8 *params, u8 size)
{
struct hidpp_ff_work_data *wd = kzalloc(sizeof(*wd), GFP_KERNEL);
int s;
if (!wd)
return -ENOMEM;
INIT_WORK(&wd->work, hidpp_ff_work_handler);
wd->data = data;
wd->effect_id = effect_id;
wd->command = command;
wd->size = size;
memcpy(wd->params, params, size);
atomic_inc(&data->workqueue_size);
queue_work(data->wq, &wd->work);
/* warn about excessive queue size */
s = atomic_read(&data->workqueue_size);
if (s >= 20 && s % 20 == 0)
hid_warn(data->hidpp->hid_dev, "Force feedback command queue contains %d commands, causing substantial delays!", s);
return 0;
}
static int hidpp_ff_upload_effect(struct input_dev *dev, struct ff_effect *effect, struct ff_effect *old)
{
struct hidpp_ff_private_data *data = dev->ff->private;
u8 params[20];
u8 size;
int force;
/* set common parameters */
params[2] = effect->replay.length >> 8;
params[3] = effect->replay.length & 255;
params[4] = effect->replay.delay >> 8;
params[5] = effect->replay.delay & 255;
switch (effect->type) {
case FF_CONSTANT:
force = (effect->u.constant.level * fixp_sin16((effect->direction * 360) >> 16)) >> 15;
params[1] = HIDPP_FF_EFFECT_CONSTANT;
params[6] = force >> 8;
params[7] = force & 255;
params[8] = effect->u.constant.envelope.attack_level >> 7;
params[9] = effect->u.constant.envelope.attack_length >> 8;
params[10] = effect->u.constant.envelope.attack_length & 255;
params[11] = effect->u.constant.envelope.fade_level >> 7;
params[12] = effect->u.constant.envelope.fade_length >> 8;
params[13] = effect->u.constant.envelope.fade_length & 255;
size = 14;
dbg_hid("Uploading constant force level=%d in dir %d = %d\n",
effect->u.constant.level,
effect->direction, force);
dbg_hid(" envelope attack=(%d, %d ms) fade=(%d, %d ms)\n",
effect->u.constant.envelope.attack_level,
effect->u.constant.envelope.attack_length,
effect->u.constant.envelope.fade_level,
effect->u.constant.envelope.fade_length);
break;
case FF_PERIODIC:
{
switch (effect->u.periodic.waveform) {
case FF_SINE:
params[1] = HIDPP_FF_EFFECT_PERIODIC_SINE;
break;
case FF_SQUARE:
params[1] = HIDPP_FF_EFFECT_PERIODIC_SQUARE;
break;
case FF_SAW_UP:
params[1] = HIDPP_FF_EFFECT_PERIODIC_SAWTOOTHUP;
break;
case FF_SAW_DOWN:
params[1] = HIDPP_FF_EFFECT_PERIODIC_SAWTOOTHDOWN;
break;
case FF_TRIANGLE:
params[1] = HIDPP_FF_EFFECT_PERIODIC_TRIANGLE;
break;
default:
hid_err(data->hidpp->hid_dev, "Unexpected periodic waveform type %i!\n", effect->u.periodic.waveform);
return -EINVAL;
}
force = (effect->u.periodic.magnitude * fixp_sin16((effect->direction * 360) >> 16)) >> 15;
params[6] = effect->u.periodic.magnitude >> 8;
params[7] = effect->u.periodic.magnitude & 255;
params[8] = effect->u.periodic.offset >> 8;
params[9] = effect->u.periodic.offset & 255;
params[10] = effect->u.periodic.period >> 8;
params[11] = effect->u.periodic.period & 255;
params[12] = effect->u.periodic.phase >> 8;
params[13] = effect->u.periodic.phase & 255;
params[14] = effect->u.periodic.envelope.attack_level >> 7;
params[15] = effect->u.periodic.envelope.attack_length >> 8;
params[16] = effect->u.periodic.envelope.attack_length & 255;
params[17] = effect->u.periodic.envelope.fade_level >> 7;
params[18] = effect->u.periodic.envelope.fade_length >> 8;
params[19] = effect->u.periodic.envelope.fade_length & 255;
size = 20;
dbg_hid("Uploading periodic force mag=%d/dir=%d, offset=%d, period=%d ms, phase=%d\n",
effect->u.periodic.magnitude, effect->direction,
effect->u.periodic.offset,
effect->u.periodic.period,
effect->u.periodic.phase);
dbg_hid(" envelope attack=(%d, %d ms) fade=(%d, %d ms)\n",
effect->u.periodic.envelope.attack_level,
effect->u.periodic.envelope.attack_length,
effect->u.periodic.envelope.fade_level,
effect->u.periodic.envelope.fade_length);
break;
}
case FF_RAMP:
params[1] = HIDPP_FF_EFFECT_RAMP;
force = (effect->u.ramp.start_level * fixp_sin16((effect->direction * 360) >> 16)) >> 15;
params[6] = force >> 8;
params[7] = force & 255;
force = (effect->u.ramp.end_level * fixp_sin16((effect->direction * 360) >> 16)) >> 15;
params[8] = force >> 8;
params[9] = force & 255;
params[10] = effect->u.ramp.envelope.attack_level >> 7;
params[11] = effect->u.ramp.envelope.attack_length >> 8;
params[12] = effect->u.ramp.envelope.attack_length & 255;
params[13] = effect->u.ramp.envelope.fade_level >> 7;
params[14] = effect->u.ramp.envelope.fade_length >> 8;
params[15] = effect->u.ramp.envelope.fade_length & 255;
size = 16;
dbg_hid("Uploading ramp force level=%d -> %d in dir %d = %d\n",
effect->u.ramp.start_level,
effect->u.ramp.end_level,
effect->direction, force);
dbg_hid(" envelope attack=(%d, %d ms) fade=(%d, %d ms)\n",
effect->u.ramp.envelope.attack_level,
effect->u.ramp.envelope.attack_length,
effect->u.ramp.envelope.fade_level,
effect->u.ramp.envelope.fade_length);
break;
case FF_FRICTION:
case FF_INERTIA:
case FF_SPRING:
case FF_DAMPER:
params[1] = HIDPP_FF_CONDITION_CMDS[effect->type - FF_SPRING];
params[6] = effect->u.condition[0].left_saturation >> 9;
params[7] = (effect->u.condition[0].left_saturation >> 1) & 255;
params[8] = effect->u.condition[0].left_coeff >> 8;
params[9] = effect->u.condition[0].left_coeff & 255;
params[10] = effect->u.condition[0].deadband >> 9;
params[11] = (effect->u.condition[0].deadband >> 1) & 255;
params[12] = effect->u.condition[0].center >> 8;
params[13] = effect->u.condition[0].center & 255;
params[14] = effect->u.condition[0].right_coeff >> 8;
params[15] = effect->u.condition[0].right_coeff & 255;
params[16] = effect->u.condition[0].right_saturation >> 9;
params[17] = (effect->u.condition[0].right_saturation >> 1) & 255;
size = 18;
dbg_hid("Uploading %s force left coeff=%d, left sat=%d, right coeff=%d, right sat=%d\n",
HIDPP_FF_CONDITION_NAMES[effect->type - FF_SPRING],
effect->u.condition[0].left_coeff,
effect->u.condition[0].left_saturation,
effect->u.condition[0].right_coeff,
effect->u.condition[0].right_saturation);
dbg_hid(" deadband=%d, center=%d\n",
effect->u.condition[0].deadband,
effect->u.condition[0].center);
break;
default:
hid_err(data->hidpp->hid_dev, "Unexpected force type %i!\n", effect->type);
return -EINVAL;
}
return hidpp_ff_queue_work(data, effect->id, HIDPP_FF_DOWNLOAD_EFFECT, params, size);
}
static int hidpp_ff_playback(struct input_dev *dev, int effect_id, int value)
{
struct hidpp_ff_private_data *data = dev->ff->private;
u8 params[2];
params[1] = value ? HIDPP_FF_EFFECT_STATE_PLAY : HIDPP_FF_EFFECT_STATE_STOP;
dbg_hid("St%sing playback of effect %d.\n", value?"art":"opp", effect_id);
return hidpp_ff_queue_work(data, effect_id, HIDPP_FF_SET_EFFECT_STATE, params, ARRAY_SIZE(params));
}
static int hidpp_ff_erase_effect(struct input_dev *dev, int effect_id)
{
struct hidpp_ff_private_data *data = dev->ff->private;
u8 slot = 0;
dbg_hid("Erasing effect %d.\n", effect_id);
return hidpp_ff_queue_work(data, effect_id, HIDPP_FF_DESTROY_EFFECT, &slot, 1);
}
static void hidpp_ff_set_autocenter(struct input_dev *dev, u16 magnitude)
{
struct hidpp_ff_private_data *data = dev->ff->private;
u8 params[18];
dbg_hid("Setting autocenter to %d.\n", magnitude);
/* start a standard spring effect */
params[1] = HIDPP_FF_EFFECT_SPRING | HIDPP_FF_EFFECT_AUTOSTART;
/* zero delay and duration */
params[2] = params[3] = params[4] = params[5] = 0;
/* set coeff to 25% of saturation */
params[8] = params[14] = magnitude >> 11;
params[9] = params[15] = (magnitude >> 3) & 255;
params[6] = params[16] = magnitude >> 9;
params[7] = params[17] = (magnitude >> 1) & 255;
/* zero deadband and center */
params[10] = params[11] = params[12] = params[13] = 0;
hidpp_ff_queue_work(data, HIDPP_FF_EFFECTID_AUTOCENTER, HIDPP_FF_DOWNLOAD_EFFECT, params, ARRAY_SIZE(params));
}
static void hidpp_ff_set_gain(struct input_dev *dev, u16 gain)
{
struct hidpp_ff_private_data *data = dev->ff->private;
u8 params[4];
dbg_hid("Setting gain to %d.\n", gain);
params[0] = gain >> 8;
params[1] = gain & 255;
params[2] = 0; /* no boost */
params[3] = 0;
hidpp_ff_queue_work(data, HIDPP_FF_EFFECTID_NONE, HIDPP_FF_SET_GLOBAL_GAINS, params, ARRAY_SIZE(params));
}
static ssize_t hidpp_ff_range_show(struct device *dev, struct device_attribute *attr, char *buf)
{
struct hid_device *hid = to_hid_device(dev);
struct hid_input *hidinput = list_entry(hid->inputs.next, struct hid_input, list);
struct input_dev *idev = hidinput->input;
struct hidpp_ff_private_data *data = idev->ff->private;
return scnprintf(buf, PAGE_SIZE, "%u\n", data->range);
}
static ssize_t hidpp_ff_range_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
{
struct hid_device *hid = to_hid_device(dev);
struct hid_input *hidinput = list_entry(hid->inputs.next, struct hid_input, list);
struct input_dev *idev = hidinput->input;
struct hidpp_ff_private_data *data = idev->ff->private;
u8 params[2];
int range = simple_strtoul(buf, NULL, 10);
range = clamp(range, 180, 900);
params[0] = range >> 8;
params[1] = range & 0x00FF;
hidpp_ff_queue_work(data, -1, HIDPP_FF_SET_APERTURE, params, ARRAY_SIZE(params));
return count;
}
static DEVICE_ATTR(range, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP | S_IROTH, hidpp_ff_range_show, hidpp_ff_range_store);
static void hidpp_ff_destroy(struct ff_device *ff)
{
struct hidpp_ff_private_data *data = ff->private;
kfree(data->effect_ids);
}
static int hidpp_ff_init(struct hidpp_device *hidpp, u8 feature_index)
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
{
struct hid_device *hid = hidpp->hid_dev;
struct hid_input *hidinput = list_entry(hid->inputs.next, struct hid_input, list);
struct input_dev *dev = hidinput->input;
const struct usb_device_descriptor *udesc = &(hid_to_usb_dev(hid)->descriptor);
const u16 bcdDevice = le16_to_cpu(udesc->bcdDevice);
struct ff_device *ff;
struct hidpp_report response;
struct hidpp_ff_private_data *data;
int error, j, num_slots;
u8 version;
if (!dev) {
hid_err(hid, "Struct input_dev not set!\n");
return -EINVAL;
}
/* Get firmware release */
version = bcdDevice & 255;
/* Set supported force feedback capabilities */
for (j = 0; hidpp_ff_effects[j] >= 0; j++)
set_bit(hidpp_ff_effects[j], dev->ffbit);
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
if (version > 1)
for (j = 0; hidpp_ff_effects_v2[j] >= 0; j++)
set_bit(hidpp_ff_effects_v2[j], dev->ffbit);
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
/* Read number of slots available in device */
error = hidpp_send_fap_command_sync(hidpp, feature_index,
HIDPP_FF_GET_INFO, NULL, 0, &response);
if (error) {
if (error < 0)
return error;
hid_err(hidpp->hid_dev, "%s: received protocol error 0x%02x\n",
__func__, error);
return -EPROTO;
}
num_slots = response.fap.params[0] - HIDPP_FF_RESERVED_SLOTS;
error = input_ff_create(dev, num_slots);
if (error) {
hid_err(dev, "Failed to create FF device!\n");
return error;
}
data = kzalloc(sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
data->effect_ids = kcalloc(num_slots, sizeof(int), GFP_KERNEL);
if (!data->effect_ids) {
kfree(data);
return -ENOMEM;
}
data->wq = create_singlethread_workqueue("hidpp-ff-sendqueue");
if (!data->wq) {
kfree(data->effect_ids);
kfree(data);
return -ENOMEM;
}
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
data->hidpp = hidpp;
data->feature_index = feature_index;
data->version = version;
data->slot_autocenter = 0;
data->num_effects = num_slots;
for (j = 0; j < num_slots; j++)
data->effect_ids[j] = -1;
ff = dev->ff;
ff->private = data;
ff->upload = hidpp_ff_upload_effect;
ff->erase = hidpp_ff_erase_effect;
ff->playback = hidpp_ff_playback;
ff->set_gain = hidpp_ff_set_gain;
ff->set_autocenter = hidpp_ff_set_autocenter;
ff->destroy = hidpp_ff_destroy;
/* reset all forces */
error = hidpp_send_fap_command_sync(hidpp, feature_index,
HIDPP_FF_RESET_ALL, NULL, 0, &response);
/* Read current Range */
error = hidpp_send_fap_command_sync(hidpp, feature_index,
HIDPP_FF_GET_APERTURE, NULL, 0, &response);
if (error)
hid_warn(hidpp->hid_dev, "Failed to read range from device!\n");
data->range = error ? 900 : get_unaligned_be16(&response.fap.params[0]);
/* Create sysfs interface */
error = device_create_file(&(hidpp->hid_dev->dev), &dev_attr_range);
if (error)
hid_warn(hidpp->hid_dev, "Unable to create sysfs interface for \"range\", errno %d!\n", error);
/* Read the current gain values */
error = hidpp_send_fap_command_sync(hidpp, feature_index,
HIDPP_FF_GET_GLOBAL_GAINS, NULL, 0, &response);
if (error)
hid_warn(hidpp->hid_dev, "Failed to read gain values from device!\n");
data->gain = error ? 0xffff : get_unaligned_be16(&response.fap.params[0]);
/* ignore boost value at response.fap.params[2] */
/* init the hardware command queue */
atomic_set(&data->workqueue_size, 0);
/* initialize with zero autocenter to get wheel in usable state */
hidpp_ff_set_autocenter(dev, 0);
hid_info(hid, "Force feedback support loaded (firmware release %d).\n",
version);
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
return 0;
}
static int hidpp_ff_deinit(struct hid_device *hid)
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
{
struct hid_input *hidinput = list_entry(hid->inputs.next, struct hid_input, list);
struct input_dev *dev = hidinput->input;
struct hidpp_ff_private_data *data;
if (!dev) {
hid_err(hid, "Struct input_dev not found!\n");
return -EINVAL;
}
hid_info(hid, "Unloading HID++ force feedback.\n");
data = dev->ff->private;
if (!data) {
hid_err(hid, "Private data not found!\n");
return -EINVAL;
}
destroy_workqueue(data->wq);
device_remove_file(&hid->dev, &dev_attr_range);
return 0;
}
/* ************************************************************************** */
/* */
/* Device Support */
/* */
/* ************************************************************************** */
/* -------------------------------------------------------------------------- */
/* Touchpad HID++ devices */
/* -------------------------------------------------------------------------- */
#define WTP_MANUAL_RESOLUTION 39
struct wtp_data {
u16 x_size, y_size;
u8 finger_count;
u8 mt_feature_index;
u8 button_feature_index;
u8 maxcontacts;
bool flip_y;
unsigned int resolution;
};
static int wtp_input_mapping(struct hid_device *hdev, struct hid_input *hi,
struct hid_field *field, struct hid_usage *usage,
unsigned long **bit, int *max)
{
return -1;
}
static void wtp_populate_input(struct hidpp_device *hidpp,
struct input_dev *input_dev)
{
struct wtp_data *wd = hidpp->private_data;
__set_bit(EV_ABS, input_dev->evbit);
__set_bit(EV_KEY, input_dev->evbit);
__clear_bit(EV_REL, input_dev->evbit);
__clear_bit(EV_LED, input_dev->evbit);
input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0, wd->x_size, 0, 0);
input_abs_set_res(input_dev, ABS_MT_POSITION_X, wd->resolution);
input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0, wd->y_size, 0, 0);
input_abs_set_res(input_dev, ABS_MT_POSITION_Y, wd->resolution);
/* Max pressure is not given by the devices, pick one */
input_set_abs_params(input_dev, ABS_MT_PRESSURE, 0, 50, 0, 0);
input_set_capability(input_dev, EV_KEY, BTN_LEFT);
if (hidpp->quirks & HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS)
input_set_capability(input_dev, EV_KEY, BTN_RIGHT);
else
__set_bit(INPUT_PROP_BUTTONPAD, input_dev->propbit);
input_mt_init_slots(input_dev, wd->maxcontacts, INPUT_MT_POINTER |
INPUT_MT_DROP_UNUSED);
}
static void wtp_touch_event(struct hidpp_device *hidpp,
struct hidpp_touchpad_raw_xy_finger *touch_report)
{
struct wtp_data *wd = hidpp->private_data;
int slot;
if (!touch_report->finger_id || touch_report->contact_type)
/* no actual data */
return;
slot = input_mt_get_slot_by_key(hidpp->input, touch_report->finger_id);
input_mt_slot(hidpp->input, slot);
input_mt_report_slot_state(hidpp->input, MT_TOOL_FINGER,
touch_report->contact_status);
if (touch_report->contact_status) {
input_event(hidpp->input, EV_ABS, ABS_MT_POSITION_X,
touch_report->x);
input_event(hidpp->input, EV_ABS, ABS_MT_POSITION_Y,
wd->flip_y ? wd->y_size - touch_report->y :
touch_report->y);
input_event(hidpp->input, EV_ABS, ABS_MT_PRESSURE,
touch_report->area);
}
}
static void wtp_send_raw_xy_event(struct hidpp_device *hidpp,
struct hidpp_touchpad_raw_xy *raw)
{
int i;
for (i = 0; i < 2; i++)
wtp_touch_event(hidpp, &(raw->fingers[i]));
if (raw->end_of_frame &&
!(hidpp->quirks & HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS))
input_event(hidpp->input, EV_KEY, BTN_LEFT, raw->button);
if (raw->end_of_frame || raw->finger_count <= 2) {
input_mt_sync_frame(hidpp->input);
input_sync(hidpp->input);
}
}
static int wtp_mouse_raw_xy_event(struct hidpp_device *hidpp, u8 *data)
{
struct wtp_data *wd = hidpp->private_data;
u8 c1_area = ((data[7] & 0xf) * (data[7] & 0xf) +
(data[7] >> 4) * (data[7] >> 4)) / 2;
u8 c2_area = ((data[13] & 0xf) * (data[13] & 0xf) +
(data[13] >> 4) * (data[13] >> 4)) / 2;
struct hidpp_touchpad_raw_xy raw = {
.timestamp = data[1],
.fingers = {
{
.contact_type = 0,
.contact_status = !!data[7],
.x = get_unaligned_le16(&data[3]),
.y = get_unaligned_le16(&data[5]),
.z = c1_area,
.area = c1_area,
.finger_id = data[2],
}, {
.contact_type = 0,
.contact_status = !!data[13],
.x = get_unaligned_le16(&data[9]),
.y = get_unaligned_le16(&data[11]),
.z = c2_area,
.area = c2_area,
.finger_id = data[8],
}
},
.finger_count = wd->maxcontacts,
.spurious_flag = 0,
.end_of_frame = (data[0] >> 7) == 0,
.button = data[0] & 0x01,
};
wtp_send_raw_xy_event(hidpp, &raw);
return 1;
}
static int wtp_raw_event(struct hid_device *hdev, u8 *data, int size)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
struct wtp_data *wd = hidpp->private_data;
struct hidpp_report *report = (struct hidpp_report *)data;
struct hidpp_touchpad_raw_xy raw;
if (!wd || !hidpp->input)
return 1;
switch (data[0]) {
case 0x02:
if (size < 2) {
hid_err(hdev, "Received HID report of bad size (%d)",
size);
return 1;
}
if (hidpp->quirks & HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS) {
input_event(hidpp->input, EV_KEY, BTN_LEFT,
!!(data[1] & 0x01));
input_event(hidpp->input, EV_KEY, BTN_RIGHT,
!!(data[1] & 0x02));
input_sync(hidpp->input);
return 0;
} else {
if (size < 21)
return 1;
return wtp_mouse_raw_xy_event(hidpp, &data[7]);
}
case REPORT_ID_HIDPP_LONG:
/* size is already checked in hidpp_raw_event. */
if ((report->fap.feature_index != wd->mt_feature_index) ||
(report->fap.funcindex_clientid != EVENT_TOUCHPAD_RAW_XY))
return 1;
hidpp_touchpad_raw_xy_event(hidpp, data + 4, &raw);
wtp_send_raw_xy_event(hidpp, &raw);
return 0;
}
return 0;
}
static int wtp_get_config(struct hidpp_device *hidpp)
{
struct wtp_data *wd = hidpp->private_data;
struct hidpp_touchpad_raw_info raw_info = {0};
u8 feature_type;
int ret;
ret = hidpp_root_get_feature(hidpp, HIDPP_PAGE_TOUCHPAD_RAW_XY,
&wd->mt_feature_index, &feature_type);
if (ret)
/* means that the device is not powered up */
return ret;
ret = hidpp_touchpad_get_raw_info(hidpp, wd->mt_feature_index,
&raw_info);
if (ret)
return ret;
wd->x_size = raw_info.x_size;
wd->y_size = raw_info.y_size;
wd->maxcontacts = raw_info.maxcontacts;
wd->flip_y = raw_info.origin == TOUCHPAD_RAW_XY_ORIGIN_LOWER_LEFT;
wd->resolution = raw_info.res;
if (!wd->resolution)
wd->resolution = WTP_MANUAL_RESOLUTION;
return 0;
}
static int wtp_allocate(struct hid_device *hdev, const struct hid_device_id *id)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
struct wtp_data *wd;
wd = devm_kzalloc(&hdev->dev, sizeof(struct wtp_data),
GFP_KERNEL);
if (!wd)
return -ENOMEM;
hidpp->private_data = wd;
return 0;
};
static int wtp_connect(struct hid_device *hdev, bool connected)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
struct wtp_data *wd = hidpp->private_data;
int ret;
if (!wd->x_size) {
ret = wtp_get_config(hidpp);
if (ret) {
hid_err(hdev, "Can not get wtp config: %d\n", ret);
return ret;
}
}
return hidpp_touchpad_set_raw_report_state(hidpp, wd->mt_feature_index,
true, true);
}
/* ------------------------------------------------------------------------- */
/* Logitech M560 devices */
/* ------------------------------------------------------------------------- */
/*
* Logitech M560 protocol overview
*
* The Logitech M560 mouse, is designed for windows 8. When the middle and/or
* the sides buttons are pressed, it sends some keyboard keys events
* instead of buttons ones.
* To complicate things further, the middle button keys sequence
* is different from the odd press and the even press.
*
* forward button -> Super_R
* backward button -> Super_L+'d' (press only)
* middle button -> 1st time: Alt_L+SuperL+XF86TouchpadOff (press only)
* 2nd time: left-click (press only)
* NB: press-only means that when the button is pressed, the
* KeyPress/ButtonPress and KeyRelease/ButtonRelease events are generated
* together sequentially; instead when the button is released, no event is
* generated !
*
* With the command
* 10<xx>0a 3500af03 (where <xx> is the mouse id),
* the mouse reacts differently:
* - it never sends a keyboard key event
* - for the three mouse button it sends:
* middle button press 11<xx>0a 3500af00...
* side 1 button (forward) press 11<xx>0a 3500b000...
* side 2 button (backward) press 11<xx>0a 3500ae00...
* middle/side1/side2 button release 11<xx>0a 35000000...
*/
static const u8 m560_config_parameter[] = {0x00, 0xaf, 0x03};
/* how buttons are mapped in the report */
#define M560_MOUSE_BTN_LEFT 0x01
#define M560_MOUSE_BTN_RIGHT 0x02
#define M560_MOUSE_BTN_WHEEL_LEFT 0x08
#define M560_MOUSE_BTN_WHEEL_RIGHT 0x10
#define M560_SUB_ID 0x0a
#define M560_BUTTON_MODE_REGISTER 0x35
static int m560_send_config_command(struct hid_device *hdev, bool connected)
{
struct hidpp_report response;
struct hidpp_device *hidpp_dev;
hidpp_dev = hid_get_drvdata(hdev);
return hidpp_send_rap_command_sync(
hidpp_dev,
REPORT_ID_HIDPP_SHORT,
M560_SUB_ID,
M560_BUTTON_MODE_REGISTER,
(u8 *)m560_config_parameter,
sizeof(m560_config_parameter),
&response
);
}
static int m560_raw_event(struct hid_device *hdev, u8 *data, int size)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
/* sanity check */
if (!hidpp->input) {
hid_err(hdev, "error in parameter\n");
return -EINVAL;
}
if (size < 7) {
hid_err(hdev, "error in report\n");
return 0;
}
if (data[0] == REPORT_ID_HIDPP_LONG &&
data[2] == M560_SUB_ID && data[6] == 0x00) {
/*
* m560 mouse report for middle, forward and backward button
*
* data[0] = 0x11
* data[1] = device-id
* data[2] = 0x0a
* data[5] = 0xaf -> middle
* 0xb0 -> forward
* 0xae -> backward
* 0x00 -> release all
* data[6] = 0x00
*/
switch (data[5]) {
case 0xaf:
input_report_key(hidpp->input, BTN_MIDDLE, 1);
break;
case 0xb0:
input_report_key(hidpp->input, BTN_FORWARD, 1);
break;
case 0xae:
input_report_key(hidpp->input, BTN_BACK, 1);
break;
case 0x00:
input_report_key(hidpp->input, BTN_BACK, 0);
input_report_key(hidpp->input, BTN_FORWARD, 0);
input_report_key(hidpp->input, BTN_MIDDLE, 0);
break;
default:
hid_err(hdev, "error in report\n");
return 0;
}
input_sync(hidpp->input);
} else if (data[0] == 0x02) {
/*
* Logitech M560 mouse report
*
* data[0] = type (0x02)
* data[1..2] = buttons
* data[3..5] = xy
* data[6] = wheel
*/
int v;
input_report_key(hidpp->input, BTN_LEFT,
!!(data[1] & M560_MOUSE_BTN_LEFT));
input_report_key(hidpp->input, BTN_RIGHT,
!!(data[1] & M560_MOUSE_BTN_RIGHT));
if (data[1] & M560_MOUSE_BTN_WHEEL_LEFT) {
input_report_rel(hidpp->input, REL_HWHEEL, -1);
input_report_rel(hidpp->input, REL_HWHEEL_HI_RES,
-120);
} else if (data[1] & M560_MOUSE_BTN_WHEEL_RIGHT) {
input_report_rel(hidpp->input, REL_HWHEEL, 1);
input_report_rel(hidpp->input, REL_HWHEEL_HI_RES,
120);
}
v = hid_snto32(hid_field_extract(hdev, data+3, 0, 12), 12);
input_report_rel(hidpp->input, REL_X, v);
v = hid_snto32(hid_field_extract(hdev, data+3, 12, 12), 12);
input_report_rel(hidpp->input, REL_Y, v);
v = hid_snto32(data[6], 8);
if (v != 0)
hidpp_scroll_counter_handle_scroll(hidpp->input,
&hidpp->vertical_wheel_counter, v);
input_sync(hidpp->input);
}
return 1;
}
static void m560_populate_input(struct hidpp_device *hidpp,
struct input_dev *input_dev)
{
__set_bit(EV_KEY, input_dev->evbit);
__set_bit(BTN_MIDDLE, input_dev->keybit);
__set_bit(BTN_RIGHT, input_dev->keybit);
__set_bit(BTN_LEFT, input_dev->keybit);
__set_bit(BTN_BACK, input_dev->keybit);
__set_bit(BTN_FORWARD, input_dev->keybit);
__set_bit(EV_REL, input_dev->evbit);
__set_bit(REL_X, input_dev->relbit);
__set_bit(REL_Y, input_dev->relbit);
__set_bit(REL_WHEEL, input_dev->relbit);
__set_bit(REL_HWHEEL, input_dev->relbit);
__set_bit(REL_WHEEL_HI_RES, input_dev->relbit);
__set_bit(REL_HWHEEL_HI_RES, input_dev->relbit);
}
static int m560_input_mapping(struct hid_device *hdev, struct hid_input *hi,
struct hid_field *field, struct hid_usage *usage,
unsigned long **bit, int *max)
{
return -1;
}
/* ------------------------------------------------------------------------- */
/* Logitech K400 devices */
/* ------------------------------------------------------------------------- */
/*
* The Logitech K400 keyboard has an embedded touchpad which is seen
* as a mouse from the OS point of view. There is a hardware shortcut to disable
* tap-to-click but the setting is not remembered accross reset, annoying some
* users.
*
* We can toggle this feature from the host by using the feature 0x6010:
* Touchpad FW items
*/
struct k400_private_data {
u8 feature_index;
};
static int k400_disable_tap_to_click(struct hidpp_device *hidpp)
{
struct k400_private_data *k400 = hidpp->private_data;
struct hidpp_touchpad_fw_items items = {};
int ret;
u8 feature_type;
if (!k400->feature_index) {
ret = hidpp_root_get_feature(hidpp,
HIDPP_PAGE_TOUCHPAD_FW_ITEMS,
&k400->feature_index, &feature_type);
if (ret)
/* means that the device is not powered up */
return ret;
}
ret = hidpp_touchpad_fw_items_set(hidpp, k400->feature_index, &items);
if (ret)
return ret;
return 0;
}
static int k400_allocate(struct hid_device *hdev)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
struct k400_private_data *k400;
k400 = devm_kzalloc(&hdev->dev, sizeof(struct k400_private_data),
GFP_KERNEL);
if (!k400)
return -ENOMEM;
hidpp->private_data = k400;
return 0;
};
static int k400_connect(struct hid_device *hdev, bool connected)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
if (!disable_tap_to_click)
return 0;
return k400_disable_tap_to_click(hidpp);
}
/* ------------------------------------------------------------------------- */
/* Logitech G920 Driving Force Racing Wheel for Xbox One */
/* ------------------------------------------------------------------------- */
#define HIDPP_PAGE_G920_FORCE_FEEDBACK 0x8123
static int g920_get_config(struct hidpp_device *hidpp)
{
u8 feature_type;
u8 feature_index;
int ret;
/* Find feature and store for later use */
ret = hidpp_root_get_feature(hidpp, HIDPP_PAGE_G920_FORCE_FEEDBACK,
&feature_index, &feature_type);
if (ret)
return ret;
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
ret = hidpp_ff_init(hidpp, feature_index);
if (ret)
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
hid_warn(hidpp->hid_dev, "Unable to initialize force feedback support, errno %d\n",
ret);
return 0;
}
/* -------------------------------------------------------------------------- */
/* HID++1.0 devices which use HID++ reports for their wheels */
/* -------------------------------------------------------------------------- */
static int hidpp10_wheel_connect(struct hidpp_device *hidpp)
{
return hidpp10_set_register(hidpp, HIDPP_REG_ENABLE_REPORTS, 0,
HIDPP_ENABLE_WHEEL_REPORT | HIDPP_ENABLE_HWHEEL_REPORT,
HIDPP_ENABLE_WHEEL_REPORT | HIDPP_ENABLE_HWHEEL_REPORT);
}
static int hidpp10_wheel_raw_event(struct hidpp_device *hidpp,
u8 *data, int size)
{
s8 value, hvalue;
if (!hidpp->input)
return -EINVAL;
if (size < 7)
return 0;
if (data[0] != REPORT_ID_HIDPP_SHORT || data[2] != HIDPP_SUB_ID_ROLLER)
return 0;
value = data[3];
hvalue = data[4];
input_report_rel(hidpp->input, REL_WHEEL, value);
input_report_rel(hidpp->input, REL_WHEEL_HI_RES, value * 120);
input_report_rel(hidpp->input, REL_HWHEEL, hvalue);
input_report_rel(hidpp->input, REL_HWHEEL_HI_RES, hvalue * 120);
input_sync(hidpp->input);
return 1;
}
static void hidpp10_wheel_populate_input(struct hidpp_device *hidpp,
struct input_dev *input_dev)
{
__set_bit(EV_REL, input_dev->evbit);
__set_bit(REL_WHEEL, input_dev->relbit);
__set_bit(REL_WHEEL_HI_RES, input_dev->relbit);
__set_bit(REL_HWHEEL, input_dev->relbit);
__set_bit(REL_HWHEEL_HI_RES, input_dev->relbit);
}
/* -------------------------------------------------------------------------- */
/* HID++1.0 mice which use HID++ reports for extra mouse buttons */
/* -------------------------------------------------------------------------- */
static int hidpp10_extra_mouse_buttons_connect(struct hidpp_device *hidpp)
{
return hidpp10_set_register(hidpp, HIDPP_REG_ENABLE_REPORTS, 0,
HIDPP_ENABLE_MOUSE_EXTRA_BTN_REPORT,
HIDPP_ENABLE_MOUSE_EXTRA_BTN_REPORT);
}
static int hidpp10_extra_mouse_buttons_raw_event(struct hidpp_device *hidpp,
u8 *data, int size)
{
int i;
if (!hidpp->input)
return -EINVAL;
if (size < 7)
return 0;
if (data[0] != REPORT_ID_HIDPP_SHORT ||
data[2] != HIDPP_SUB_ID_MOUSE_EXTRA_BTNS)
return 0;
/*
* Buttons are either delivered through the regular mouse report *or*
* through the extra buttons report. At least for button 6 how it is
* delivered differs per receiver firmware version. Even receivers with
* the same usb-id show different behavior, so we handle both cases.
*/
for (i = 0; i < 8; i++)
input_report_key(hidpp->input, BTN_MOUSE + i,
(data[3] & (1 << i)));
/* Some mice report events on button 9+, use BTN_MISC */
for (i = 0; i < 8; i++)
input_report_key(hidpp->input, BTN_MISC + i,
(data[4] & (1 << i)));
input_sync(hidpp->input);
return 1;
}
static void hidpp10_extra_mouse_buttons_populate_input(
struct hidpp_device *hidpp, struct input_dev *input_dev)
{
/* BTN_MOUSE - BTN_MOUSE+7 are set already by the descriptor */
__set_bit(BTN_0, input_dev->keybit);
__set_bit(BTN_1, input_dev->keybit);
__set_bit(BTN_2, input_dev->keybit);
__set_bit(BTN_3, input_dev->keybit);
__set_bit(BTN_4, input_dev->keybit);
__set_bit(BTN_5, input_dev->keybit);
__set_bit(BTN_6, input_dev->keybit);
__set_bit(BTN_7, input_dev->keybit);
}
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
/* -------------------------------------------------------------------------- */
/* HID++1.0 kbds which only report 0x10xx consumer usages through sub-id 0x03 */
/* -------------------------------------------------------------------------- */
/* Find the consumer-page input report desc and change Maximums to 0x107f */
static u8 *hidpp10_consumer_keys_report_fixup(struct hidpp_device *hidpp,
u8 *_rdesc, unsigned int *rsize)
{
/* Note 0 terminated so we can use strnstr to search for this. */
static const char consumer_rdesc_start[] = {
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
0x05, 0x0C, /* USAGE_PAGE (Consumer Devices) */
0x09, 0x01, /* USAGE (Consumer Control) */
0xA1, 0x01, /* COLLECTION (Application) */
0x85, 0x03, /* REPORT_ID = 3 */
0x75, 0x10, /* REPORT_SIZE (16) */
0x95, 0x02, /* REPORT_COUNT (2) */
0x15, 0x01, /* LOGICAL_MIN (1) */
0x26, 0x00 /* LOGICAL_MAX (... */
};
char *consumer_rdesc, *rdesc = (char *)_rdesc;
unsigned int size;
consumer_rdesc = strnstr(rdesc, consumer_rdesc_start, *rsize);
size = *rsize - (consumer_rdesc - rdesc);
if (consumer_rdesc && size >= 25) {
consumer_rdesc[15] = 0x7f;
consumer_rdesc[16] = 0x10;
consumer_rdesc[20] = 0x7f;
consumer_rdesc[21] = 0x10;
}
return _rdesc;
}
static int hidpp10_consumer_keys_connect(struct hidpp_device *hidpp)
{
return hidpp10_set_register(hidpp, HIDPP_REG_ENABLE_REPORTS, 0,
HIDPP_ENABLE_CONSUMER_REPORT,
HIDPP_ENABLE_CONSUMER_REPORT);
}
static int hidpp10_consumer_keys_raw_event(struct hidpp_device *hidpp,
u8 *data, int size)
{
u8 consumer_report[5];
if (size < 7)
return 0;
if (data[0] != REPORT_ID_HIDPP_SHORT ||
data[2] != HIDPP_SUB_ID_CONSUMER_VENDOR_KEYS)
return 0;
/*
* Build a normal consumer report (3) out of the data, this detour
* is necessary to get some keyboards to report their 0x10xx usages.
*/
consumer_report[0] = 0x03;
memcpy(&consumer_report[1], &data[3], 4);
/* We are called from atomic context */
hid_report_raw_event(hidpp->hid_dev, HID_INPUT_REPORT,
consumer_report, 5, 1);
return 1;
}
/* -------------------------------------------------------------------------- */
/* High-resolution scroll wheels */
/* -------------------------------------------------------------------------- */
static int hi_res_scroll_enable(struct hidpp_device *hidpp)
{
int ret;
u8 multiplier = 1;
if (hidpp->quirks & HIDPP_QUIRK_HI_RES_SCROLL_X2121) {
ret = hidpp_hrw_set_wheel_mode(hidpp, false, true, false);
if (ret == 0)
ret = hidpp_hrw_get_wheel_capability(hidpp, &multiplier);
} else if (hidpp->quirks & HIDPP_QUIRK_HI_RES_SCROLL_X2120) {
ret = hidpp_hrs_set_highres_scrolling_mode(hidpp, true,
&multiplier);
} else /* if (hidpp->quirks & HIDPP_QUIRK_HI_RES_SCROLL_1P0) */ {
ret = hidpp10_enable_scrolling_acceleration(hidpp);
multiplier = 8;
}
if (ret)
return ret;
if (multiplier == 0)
multiplier = 1;
hidpp->vertical_wheel_counter.wheel_multiplier = multiplier;
hid_info(hidpp->hid_dev, "multiplier = %d\n", multiplier);
return 0;
}
/* -------------------------------------------------------------------------- */
/* Generic HID++ devices */
/* -------------------------------------------------------------------------- */
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
static u8 *hidpp_report_fixup(struct hid_device *hdev, u8 *rdesc,
unsigned int *rsize)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
if (!hidpp)
return rdesc;
/* For 27 MHz keyboards the quirk gets set after hid_parse. */
if (hdev->group == HID_GROUP_LOGITECH_27MHZ_DEVICE ||
(hidpp->quirks & HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS))
rdesc = hidpp10_consumer_keys_report_fixup(hidpp, rdesc, rsize);
return rdesc;
}
static int hidpp_input_mapping(struct hid_device *hdev, struct hid_input *hi,
struct hid_field *field, struct hid_usage *usage,
unsigned long **bit, int *max)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
if (!hidpp)
return 0;
if (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP)
return wtp_input_mapping(hdev, hi, field, usage, bit, max);
else if (hidpp->quirks & HIDPP_QUIRK_CLASS_M560 &&
field->application != HID_GD_MOUSE)
return m560_input_mapping(hdev, hi, field, usage, bit, max);
return 0;
}
static int hidpp_input_mapped(struct hid_device *hdev, struct hid_input *hi,
struct hid_field *field, struct hid_usage *usage,
unsigned long **bit, int *max)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
if (!hidpp)
return 0;
/* Ensure that Logitech G920 is not given a default fuzz/flat value */
if (hidpp->quirks & HIDPP_QUIRK_CLASS_G920) {
if (usage->type == EV_ABS && (usage->code == ABS_X ||
usage->code == ABS_Y || usage->code == ABS_Z ||
usage->code == ABS_RZ)) {
field->application = HID_GD_MULTIAXIS;
}
}
return 0;
}
static void hidpp_populate_input(struct hidpp_device *hidpp,
struct input_dev *input)
{
hidpp->input = input;
if (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP)
wtp_populate_input(hidpp, input);
else if (hidpp->quirks & HIDPP_QUIRK_CLASS_M560)
m560_populate_input(hidpp, input);
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_WHEELS)
hidpp10_wheel_populate_input(hidpp, input);
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_EXTRA_MOUSE_BTNS)
hidpp10_extra_mouse_buttons_populate_input(hidpp, input);
}
static int hidpp_input_configured(struct hid_device *hdev,
struct hid_input *hidinput)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
struct input_dev *input = hidinput->input;
if (!hidpp)
return 0;
hidpp_populate_input(hidpp, input);
return 0;
}
static int hidpp_raw_hidpp_event(struct hidpp_device *hidpp, u8 *data,
int size)
{
struct hidpp_report *question = hidpp->send_receive_buf;
struct hidpp_report *answer = hidpp->send_receive_buf;
struct hidpp_report *report = (struct hidpp_report *)data;
int ret;
/*
* If the mutex is locked then we have a pending answer from a
* previously sent command.
*/
if (unlikely(mutex_is_locked(&hidpp->send_mutex))) {
/*
* Check for a correct hidpp20 answer or the corresponding
* error
*/
if (hidpp_match_answer(question, report) ||
hidpp_match_error(question, report)) {
*answer = *report;
hidpp->answer_available = true;
wake_up(&hidpp->wait);
/*
* This was an answer to a command that this driver sent
* We return 1 to hid-core to avoid forwarding the
* command upstream as it has been treated by the driver
*/
return 1;
}
}
if (unlikely(hidpp_report_is_connect_event(report))) {
atomic_set(&hidpp->connected,
!(report->rap.params[0] & (1 << 6)));
if (schedule_work(&hidpp->work) == 0)
dbg_hid("%s: connect event already queued\n", __func__);
return 1;
}
if (hidpp->capabilities & HIDPP_CAPABILITY_HIDPP20_BATTERY) {
ret = hidpp20_battery_event(hidpp, data, size);
if (ret != 0)
return ret;
ret = hidpp_solar_battery_event(hidpp, data, size);
if (ret != 0)
return ret;
}
if (hidpp->capabilities & HIDPP_CAPABILITY_HIDPP10_BATTERY) {
ret = hidpp10_battery_event(hidpp, data, size);
if (ret != 0)
return ret;
}
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_WHEELS) {
ret = hidpp10_wheel_raw_event(hidpp, data, size);
if (ret != 0)
return ret;
}
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_EXTRA_MOUSE_BTNS) {
ret = hidpp10_extra_mouse_buttons_raw_event(hidpp, data, size);
if (ret != 0)
return ret;
}
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS) {
ret = hidpp10_consumer_keys_raw_event(hidpp, data, size);
if (ret != 0)
return ret;
}
return 0;
}
static int hidpp_raw_event(struct hid_device *hdev, struct hid_report *report,
u8 *data, int size)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
int ret = 0;
if (!hidpp)
return 0;
/* Generic HID++ processing. */
switch (data[0]) {
case REPORT_ID_HIDPP_VERY_LONG:
if (size != hidpp->very_long_report_length) {
hid_err(hdev, "received hid++ report of bad size (%d)",
size);
return 1;
}
ret = hidpp_raw_hidpp_event(hidpp, data, size);
break;
case REPORT_ID_HIDPP_LONG:
if (size != HIDPP_REPORT_LONG_LENGTH) {
hid_err(hdev, "received hid++ report of bad size (%d)",
size);
return 1;
}
ret = hidpp_raw_hidpp_event(hidpp, data, size);
break;
case REPORT_ID_HIDPP_SHORT:
if (size != HIDPP_REPORT_SHORT_LENGTH) {
hid_err(hdev, "received hid++ report of bad size (%d)",
size);
return 1;
}
ret = hidpp_raw_hidpp_event(hidpp, data, size);
break;
}
/* If no report is available for further processing, skip calling
* raw_event of subclasses. */
if (ret != 0)
return ret;
if (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP)
return wtp_raw_event(hdev, data, size);
else if (hidpp->quirks & HIDPP_QUIRK_CLASS_M560)
return m560_raw_event(hdev, data, size);
return 0;
}
static int hidpp_event(struct hid_device *hdev, struct hid_field *field,
struct hid_usage *usage, __s32 value)
{
/* This function will only be called for scroll events, due to the
* restriction imposed in hidpp_usages.
*/
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
struct hidpp_scroll_counter *counter;
if (!hidpp)
return 0;
counter = &hidpp->vertical_wheel_counter;
/* A scroll event may occur before the multiplier has been retrieved or
* the input device set, or high-res scroll enabling may fail. In such
* cases we must return early (falling back to default behaviour) to
* avoid a crash in hidpp_scroll_counter_handle_scroll.
*/
if (!(hidpp->quirks & HIDPP_QUIRK_HI_RES_SCROLL) || value == 0
|| hidpp->input == NULL || counter->wheel_multiplier == 0)
return 0;
hidpp_scroll_counter_handle_scroll(hidpp->input, counter, value);
return 1;
}
static int hidpp_initialize_battery(struct hidpp_device *hidpp)
{
static atomic_t battery_no = ATOMIC_INIT(0);
struct power_supply_config cfg = { .drv_data = hidpp };
struct power_supply_desc *desc = &hidpp->battery.desc;
enum power_supply_property *battery_props;
struct hidpp_battery *battery;
unsigned int num_battery_props;
unsigned long n;
int ret;
if (hidpp->battery.ps)
return 0;
hidpp->battery.feature_index = 0xff;
hidpp->battery.solar_feature_index = 0xff;
if (hidpp->protocol_major >= 2) {
if (hidpp->quirks & HIDPP_QUIRK_CLASS_K750)
ret = hidpp_solar_request_battery_event(hidpp);
else
ret = hidpp20_query_battery_info(hidpp);
if (ret)
return ret;
hidpp->capabilities |= HIDPP_CAPABILITY_HIDPP20_BATTERY;
} else {
ret = hidpp10_query_battery_status(hidpp);
if (ret) {
ret = hidpp10_query_battery_mileage(hidpp);
if (ret)
return -ENOENT;
hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_MILEAGE;
} else {
hidpp->capabilities |= HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS;
}
hidpp->capabilities |= HIDPP_CAPABILITY_HIDPP10_BATTERY;
}
battery_props = devm_kmemdup(&hidpp->hid_dev->dev,
hidpp_battery_props,
sizeof(hidpp_battery_props),
GFP_KERNEL);
if (!battery_props)
return -ENOMEM;
num_battery_props = ARRAY_SIZE(hidpp_battery_props) - 2;
if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_MILEAGE)
battery_props[num_battery_props++] =
POWER_SUPPLY_PROP_CAPACITY;
if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_LEVEL_STATUS)
battery_props[num_battery_props++] =
POWER_SUPPLY_PROP_CAPACITY_LEVEL;
battery = &hidpp->battery;
n = atomic_inc_return(&battery_no) - 1;
desc->properties = battery_props;
desc->num_properties = num_battery_props;
desc->get_property = hidpp_battery_get_property;
sprintf(battery->name, "hidpp_battery_%ld", n);
desc->name = battery->name;
desc->type = POWER_SUPPLY_TYPE_BATTERY;
desc->use_for_apm = 0;
battery->ps = devm_power_supply_register(&hidpp->hid_dev->dev,
&battery->desc,
&cfg);
if (IS_ERR(battery->ps))
return PTR_ERR(battery->ps);
power_supply_powers(battery->ps, &hidpp->hid_dev->dev);
return ret;
}
static void hidpp_overwrite_name(struct hid_device *hdev)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
char *name;
if (hidpp->protocol_major < 2)
return;
name = hidpp_get_device_name(hidpp);
if (!name) {
hid_err(hdev, "unable to retrieve the name of the device");
} else {
dbg_hid("HID++: Got name: %s\n", name);
snprintf(hdev->name, sizeof(hdev->name), "%s", name);
}
kfree(name);
}
static int hidpp_input_open(struct input_dev *dev)
{
struct hid_device *hid = input_get_drvdata(dev);
return hid_hw_open(hid);
}
static void hidpp_input_close(struct input_dev *dev)
{
struct hid_device *hid = input_get_drvdata(dev);
hid_hw_close(hid);
}
static struct input_dev *hidpp_allocate_input(struct hid_device *hdev)
{
struct input_dev *input_dev = devm_input_allocate_device(&hdev->dev);
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
if (!input_dev)
return NULL;
input_set_drvdata(input_dev, hdev);
input_dev->open = hidpp_input_open;
input_dev->close = hidpp_input_close;
input_dev->name = hidpp->name;
input_dev->phys = hdev->phys;
input_dev->uniq = hdev->uniq;
input_dev->id.bustype = hdev->bus;
input_dev->id.vendor = hdev->vendor;
input_dev->id.product = hdev->product;
input_dev->id.version = hdev->version;
input_dev->dev.parent = &hdev->dev;
return input_dev;
}
static void hidpp_connect_event(struct hidpp_device *hidpp)
{
struct hid_device *hdev = hidpp->hid_dev;
int ret = 0;
bool connected = atomic_read(&hidpp->connected);
struct input_dev *input;
char *name, *devm_name;
if (!connected) {
if (hidpp->battery.ps) {
hidpp->battery.online = false;
hidpp->battery.status = POWER_SUPPLY_STATUS_UNKNOWN;
hidpp->battery.level = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN;
power_supply_changed(hidpp->battery.ps);
}
return;
}
if (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP) {
ret = wtp_connect(hdev, connected);
if (ret)
return;
} else if (hidpp->quirks & HIDPP_QUIRK_CLASS_M560) {
ret = m560_send_config_command(hdev, connected);
if (ret)
return;
} else if (hidpp->quirks & HIDPP_QUIRK_CLASS_K400) {
ret = k400_connect(hdev, connected);
if (ret)
return;
}
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_WHEELS) {
ret = hidpp10_wheel_connect(hidpp);
if (ret)
return;
}
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_EXTRA_MOUSE_BTNS) {
ret = hidpp10_extra_mouse_buttons_connect(hidpp);
if (ret)
return;
}
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
if (hidpp->quirks & HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS) {
ret = hidpp10_consumer_keys_connect(hidpp);
if (ret)
return;
}
/* the device is already connected, we can ask for its name and
* protocol */
if (!hidpp->protocol_major) {
ret = hidpp_root_get_protocol_version(hidpp);
if (ret) {
hid_err(hdev, "Can not get the protocol version.\n");
return;
}
}
if (hidpp->name == hdev->name && hidpp->protocol_major >= 2) {
name = hidpp_get_device_name(hidpp);
if (name) {
devm_name = devm_kasprintf(&hdev->dev, GFP_KERNEL,
"%s", name);
kfree(name);
if (!devm_name)
return;
hidpp->name = devm_name;
}
}
hidpp_initialize_battery(hidpp);
/* forward current battery state */
if (hidpp->capabilities & HIDPP_CAPABILITY_HIDPP10_BATTERY) {
hidpp10_enable_battery_reporting(hidpp);
if (hidpp->capabilities & HIDPP_CAPABILITY_BATTERY_MILEAGE)
hidpp10_query_battery_mileage(hidpp);
else
hidpp10_query_battery_status(hidpp);
} else if (hidpp->capabilities & HIDPP_CAPABILITY_HIDPP20_BATTERY) {
hidpp20_query_battery_info(hidpp);
}
if (hidpp->battery.ps)
power_supply_changed(hidpp->battery.ps);
if (hidpp->quirks & HIDPP_QUIRK_HI_RES_SCROLL)
hi_res_scroll_enable(hidpp);
if (!(hidpp->quirks & HIDPP_QUIRK_NO_HIDINPUT) || hidpp->delayed_input)
/* if the input nodes are already created, we can stop now */
return;
input = hidpp_allocate_input(hdev);
if (!input) {
hid_err(hdev, "cannot allocate new input device: %d\n", ret);
return;
}
hidpp_populate_input(hidpp, input);
ret = input_register_device(input);
if (ret)
input_free_device(input);
hidpp->delayed_input = input;
}
static DEVICE_ATTR(builtin_power_supply, 0000, NULL, NULL);
static struct attribute *sysfs_attrs[] = {
&dev_attr_builtin_power_supply.attr,
NULL
};
static const struct attribute_group ps_attribute_group = {
.attrs = sysfs_attrs
};
static int hidpp_get_report_length(struct hid_device *hdev, int id)
{
struct hid_report_enum *re;
struct hid_report *report;
re = &(hdev->report_enum[HID_OUTPUT_REPORT]);
report = re->report_id_hash[id];
if (!report)
return 0;
return report->field[0]->report_count + 1;
}
static bool hidpp_validate_report(struct hid_device *hdev, int id,
int expected_length, bool optional)
{
int report_length;
if (id >= HID_MAX_IDS || id < 0) {
hid_err(hdev, "invalid HID report id %u\n", id);
return false;
}
report_length = hidpp_get_report_length(hdev, id);
if (!report_length)
return optional;
if (report_length < expected_length) {
hid_warn(hdev, "not enough values in hidpp report %d\n", id);
return false;
}
return true;
}
static bool hidpp_validate_device(struct hid_device *hdev)
{
return hidpp_validate_report(hdev, REPORT_ID_HIDPP_SHORT,
HIDPP_REPORT_SHORT_LENGTH, false) &&
hidpp_validate_report(hdev, REPORT_ID_HIDPP_LONG,
HIDPP_REPORT_LONG_LENGTH, true);
}
static bool hidpp_application_equals(struct hid_device *hdev,
unsigned int application)
{
struct list_head *report_list;
struct hid_report *report;
report_list = &hdev->report_enum[HID_INPUT_REPORT].report_list;
report = list_first_entry_or_null(report_list, struct hid_report, list);
return report && report->application == application;
}
static int hidpp_probe(struct hid_device *hdev, const struct hid_device_id *id)
{
struct hidpp_device *hidpp;
int ret;
bool connected;
unsigned int connect_mask = HID_CONNECT_DEFAULT;
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
/* report_fixup needs drvdata to be set before we call hid_parse */
hidpp = devm_kzalloc(&hdev->dev, sizeof(*hidpp), GFP_KERNEL);
if (!hidpp)
return -ENOMEM;
hidpp->hid_dev = hdev;
hidpp->name = hdev->name;
hidpp->quirks = id->driver_data;
hid_set_drvdata(hdev, hidpp);
ret = hid_parse(hdev);
if (ret) {
hid_err(hdev, "%s:parse failed\n", __func__);
return ret;
}
/*
* Make sure the device is HID++ capable, otherwise treat as generic HID
*/
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
if (!hidpp_validate_device(hdev)) {
hid_set_drvdata(hdev, NULL);
devm_kfree(&hdev->dev, hidpp);
return hid_hw_start(hdev, HID_CONNECT_DEFAULT);
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
}
hidpp->very_long_report_length =
hidpp_get_report_length(hdev, REPORT_ID_HIDPP_VERY_LONG);
if (hidpp->very_long_report_length > HIDPP_REPORT_VERY_LONG_MAX_LENGTH)
hidpp->very_long_report_length = HIDPP_REPORT_VERY_LONG_MAX_LENGTH;
if (id->group == HID_GROUP_LOGITECH_DJ_DEVICE)
hidpp->quirks |= HIDPP_QUIRK_UNIFYING;
if (id->group == HID_GROUP_LOGITECH_27MHZ_DEVICE &&
hidpp_application_equals(hdev, HID_GD_MOUSE))
hidpp->quirks |= HIDPP_QUIRK_HIDPP_WHEELS |
HIDPP_QUIRK_HIDPP_EXTRA_MOUSE_BTNS;
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
if (id->group == HID_GROUP_LOGITECH_27MHZ_DEVICE &&
hidpp_application_equals(hdev, HID_GD_KEYBOARD))
hidpp->quirks |= HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS;
if (disable_raw_mode) {
hidpp->quirks &= ~HIDPP_QUIRK_CLASS_WTP;
hidpp->quirks &= ~HIDPP_QUIRK_NO_HIDINPUT;
}
if (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP) {
ret = wtp_allocate(hdev, id);
if (ret)
return ret;
} else if (hidpp->quirks & HIDPP_QUIRK_CLASS_K400) {
ret = k400_allocate(hdev);
if (ret)
return ret;
}
INIT_WORK(&hidpp->work, delayed_work_cb);
mutex_init(&hidpp->send_mutex);
init_waitqueue_head(&hidpp->wait);
/* indicates we are handling the battery properties in the kernel */
ret = sysfs_create_group(&hdev->dev.kobj, &ps_attribute_group);
if (ret)
hid_warn(hdev, "Cannot allocate sysfs group for %s\n",
hdev->name);
/*
* Plain USB connections need to actually call start and open
* on the transport driver to allow incoming data.
*/
ret = hid_hw_start(hdev, 0);
if (ret) {
hid_err(hdev, "hw start failed\n");
goto hid_hw_start_fail;
}
ret = hid_hw_open(hdev);
if (ret < 0) {
dev_err(&hdev->dev, "%s:hid_hw_open returned error:%d\n",
__func__, ret);
hid_hw_stop(hdev);
goto hid_hw_open_fail;
}
/* Allow incoming packets */
hid_device_io_start(hdev);
if (hidpp->quirks & HIDPP_QUIRK_UNIFYING)
hidpp_unifying_init(hidpp);
connected = hidpp_root_get_protocol_version(hidpp) == 0;
atomic_set(&hidpp->connected, connected);
if (!(hidpp->quirks & HIDPP_QUIRK_UNIFYING)) {
if (!connected) {
ret = -ENODEV;
hid_err(hdev, "Device not connected");
goto hid_hw_init_fail;
}
hidpp_overwrite_name(hdev);
}
if (connected && (hidpp->quirks & HIDPP_QUIRK_CLASS_WTP)) {
ret = wtp_get_config(hidpp);
if (ret)
goto hid_hw_init_fail;
} else if (connected && (hidpp->quirks & HIDPP_QUIRK_CLASS_G920)) {
ret = g920_get_config(hidpp);
if (ret)
goto hid_hw_init_fail;
}
hidpp_connect_event(hidpp);
/* Reset the HID node state */
hid_device_io_stop(hdev);
hid_hw_close(hdev);
hid_hw_stop(hdev);
if (hidpp->quirks & HIDPP_QUIRK_NO_HIDINPUT)
connect_mask &= ~HID_CONNECT_HIDINPUT;
/* Now export the actual inputs and hidraw nodes to the world */
ret = hid_hw_start(hdev, connect_mask);
if (ret) {
hid_err(hdev, "%s:hid_hw_start returned error\n", __func__);
goto hid_hw_start_fail;
}
return ret;
hid_hw_init_fail:
hid_hw_close(hdev);
hid_hw_open_fail:
hid_hw_stop(hdev);
hid_hw_start_fail:
sysfs_remove_group(&hdev->dev.kobj, &ps_attribute_group);
cancel_work_sync(&hidpp->work);
mutex_destroy(&hidpp->send_mutex);
return ret;
}
static void hidpp_remove(struct hid_device *hdev)
{
struct hidpp_device *hidpp = hid_get_drvdata(hdev);
if (!hidpp)
return hid_hw_stop(hdev);
sysfs_remove_group(&hdev->dev.kobj, &ps_attribute_group);
if (hidpp->quirks & HIDPP_QUIRK_CLASS_G920)
HID: logitech-hidpp: Force feedback support for the Logitech G920 This patch implements force feedback support for the Logitech G920 Driving Force Racing Wheel. It is a generic implementation of feature 0x8123 of the Logitech HID++ protocol and should be usable for any future devices that implement this feature. This patch should be applied after the basic G920 support patch by Simon Wood: http://www.spinics.net/lists/linux-input/msg42174.html The driving supports everything that is supported by the G920 firmware: FF_CONSTANT FF_PERIODIC FF_SINE FF_SQUARE FF_SAW_UP FF_SAW_DOWN FF_TRIANGLE FF_SPRING FF_DAMPER FF_AUTOCENTER FF_GAIN and for version 2 firmware also: FF_FRICTION FF_INERTIA FF_RAMP Both envelopes and replay values are supported as well, but some problems may occur when using firmware release 1. There is also a small residual clockwise damper in the wheel when using the first firmware release. All problems are fixed in the soon te be released firmware version 2. The default spring is disabled by permanently placing a spring force in the wheel. This spring is also used as the autocenter spring. Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck in XBox since the xpad changes where not included). Michal has an alternative approach documented here (and the changes should be submitted upstream to usb_modeswitch project): === Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the following content: DefaultVendor=046d DefaultProduct=c261 MessageEndpoint=01 ResponseEndpoint=01 TargetClass=0x03 MessageContent="0f00010142" Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and watch the magic happen:) === [jkosina@suse.cz: added information about mode switching from Simon] [jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon] [jkosina@suse.cz: fix merge conflict due to to_hid_device() changes] Signed-off-by: Edwin Velds <e.velds@gmail.com> Tested-by: Elias Vanderstuyft <elias.vds@gmail.com> Tested-by: Simon Wood <simon@mungewell.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-01-11 07:25:15 +08:00
hidpp_ff_deinit(hdev);
hid_hw_stop(hdev);
cancel_work_sync(&hidpp->work);
mutex_destroy(&hidpp->send_mutex);
}
#define LDJ_DEVICE(product) \
HID_DEVICE(BUS_USB, HID_GROUP_LOGITECH_DJ_DEVICE, \
USB_VENDOR_ID_LOGITECH, (product))
#define L27MHZ_DEVICE(product) \
HID_DEVICE(BUS_USB, HID_GROUP_LOGITECH_27MHZ_DEVICE, \
USB_VENDOR_ID_LOGITECH, (product))
static const struct hid_device_id hidpp_devices[] = {
{ /* wireless touchpad */
LDJ_DEVICE(0x4011),
.driver_data = HIDPP_QUIRK_CLASS_WTP | HIDPP_QUIRK_DELAYED_INIT |
HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS },
{ /* wireless touchpad T650 */
LDJ_DEVICE(0x4101),
.driver_data = HIDPP_QUIRK_CLASS_WTP | HIDPP_QUIRK_DELAYED_INIT },
{ /* wireless touchpad T651 */
HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH,
USB_DEVICE_ID_LOGITECH_T651),
.driver_data = HIDPP_QUIRK_CLASS_WTP },
{ /* Mouse Logitech Anywhere MX */
LDJ_DEVICE(0x1017), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_1P0 },
{ /* Mouse Logitech Cube */
LDJ_DEVICE(0x4010), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2120 },
{ /* Mouse Logitech M335 */
LDJ_DEVICE(0x4050), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech M515 */
LDJ_DEVICE(0x4007), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2120 },
{ /* Mouse logitech M560 */
LDJ_DEVICE(0x402d),
.driver_data = HIDPP_QUIRK_DELAYED_INIT | HIDPP_QUIRK_CLASS_M560
| HIDPP_QUIRK_HI_RES_SCROLL_X2120 },
{ /* Mouse Logitech M705 (firmware RQM17) */
LDJ_DEVICE(0x101b), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_1P0 },
{ /* Mouse Logitech M705 (firmware RQM67) */
LDJ_DEVICE(0x406d), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech M720 */
LDJ_DEVICE(0x405e), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech MX Anywhere 2 */
LDJ_DEVICE(0x404a), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ LDJ_DEVICE(0xb013), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ LDJ_DEVICE(0xb018), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ LDJ_DEVICE(0xb01f), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech MX Anywhere 2S */
LDJ_DEVICE(0x406a), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech MX Master */
LDJ_DEVICE(0x4041), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ LDJ_DEVICE(0x4060), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ LDJ_DEVICE(0x4071), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech MX Master 2S */
LDJ_DEVICE(0x4069), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_X2121 },
{ /* Mouse Logitech Performance MX */
LDJ_DEVICE(0x101a), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_1P0 },
{ /* Keyboard logitech K400 */
LDJ_DEVICE(0x4024),
.driver_data = HIDPP_QUIRK_CLASS_K400 },
{ /* Solar Keyboard Logitech K750 */
LDJ_DEVICE(0x4002),
.driver_data = HIDPP_QUIRK_CLASS_K750 },
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
{ /* Keyboard MX5000 (Bluetooth-receiver in HID proxy mode) */
LDJ_DEVICE(0xb305),
.driver_data = HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS },
{ /* Keyboard MX5500 (Bluetooth-receiver in HID proxy mode) */
LDJ_DEVICE(0xb30b),
.driver_data = HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS },
{ LDJ_DEVICE(HID_ANY_ID) },
{ /* Keyboard LX501 (Y-RR53) */
L27MHZ_DEVICE(0x0049),
.driver_data = HIDPP_QUIRK_KBD_ZOOM_WHEEL },
{ /* Keyboard MX3000 (Y-RAM74) */
L27MHZ_DEVICE(0x0057),
.driver_data = HIDPP_QUIRK_KBD_SCROLL_WHEEL },
{ /* Keyboard MX3200 (Y-RAV80) */
L27MHZ_DEVICE(0x005c),
.driver_data = HIDPP_QUIRK_KBD_ZOOM_WHEEL },
{ /* S510 Media Remote */
L27MHZ_DEVICE(0x00fe),
.driver_data = HIDPP_QUIRK_KBD_SCROLL_WHEEL },
{ L27MHZ_DEVICE(HID_ANY_ID) },
{ /* Logitech G203/Prodigy Gaming Mouse */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC084) },
{ /* Logitech G302 Gaming Mouse */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC07F) },
{ /* Logitech G303 Gaming Mouse */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC080) },
{ /* Logitech G400 Gaming Mouse */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC07E) },
{ /* Logitech G403 Wireless Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC082) },
{ /* Logitech G403 Gaming Mouse */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC083) },
{ /* Logitech G403 Hero Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC08F) },
{ /* Logitech G502 Proteus Core Gaming Mouse */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC07D) },
{ /* Logitech G502 Proteus Spectrum Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC332) },
{ /* Logitech G502 Hero Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC08B) },
{ /* Logitech G700 Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC06B) },
{ /* Logitech G700s Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC07C) },
{ /* Logitech G703 Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC087) },
{ /* Logitech G703 Hero Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC090) },
{ /* Logitech G900 Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC081) },
{ /* Logitech G903 Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC086) },
{ /* Logitech G903 Hero Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC091) },
{ /* Logitech G920 Wheel over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_G920_WHEEL),
.driver_data = HIDPP_QUIRK_CLASS_G920 | HIDPP_QUIRK_FORCE_OUTPUT_REPORTS},
{ /* Logitech G Pro Gaming Mouse over USB */
HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, 0xC088) },
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
{ /* MX5000 keyboard over Bluetooth */
HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH, 0xb305),
.driver_data = HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS },
{ /* MX5500 keyboard over Bluetooth */
HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH, 0xb30b),
.driver_data = HIDPP_QUIRK_HIDPP_CONSUMER_VENDOR_KEYS },
{}
};
MODULE_DEVICE_TABLE(hid, hidpp_devices);
static const struct hid_usage_id hidpp_usages[] = {
{ HID_GD_WHEEL, EV_REL, REL_WHEEL_HI_RES },
{ HID_ANY_ID - 1, HID_ANY_ID - 1, HID_ANY_ID - 1}
};
static struct hid_driver hidpp_driver = {
.name = "logitech-hidpp-device",
.id_table = hidpp_devices,
HID: logitech-hidpp: add support for HID++ 1.0 consumer keys reports All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use Logitech custom usages of 0x10xx in the consumer page. The descriptor for the consumer input-report only declares usages up to 652, so we end up dropping all the input-reports reporting 0x10xx usages without reporting events for these to userspace. This commit adds a descriptor_fixup function for this which changes the usage and logical maximum to 0x107f. Mapping these usages to something other then KEY_UNKNOWN is left to userspace (hwdb). Note: 1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d this is not high enough, the S520 keyboard battery key sends 0x106f. 2. The descriptor_fixup is flexible so that it works with both the kbd- desc. passed by the logitech-dj code and with bluetooth descriptors. The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is not enough to get all keys to work on 27 MHz keyboards and just the fixup is not enough to get the MX5000 to generate 0x10xx events: 1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media" (called "Media Player" by SetPoint) and a button with a remote-control symbol ("Media Life" in SetPoint) which both send an identical consumer usage-page code (0x0183) making the 2 buttons indistinguishable, switching to HID++ 1.0 consumer keys reports makes the remote-control symbol button generate a 0x10xx Logitech specific code instead. 2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer page usages, but unlike 27 MHz devices which happily send 0x10xx codes in their normal consumer-page input-report, the MX5000 honors the maximum of 652 from its descriptor and sends a 0x0000 code (so release) whenever these keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer keys reports these 0x10xx codes do get properly reported. This commit adds support for HID++ 1.0 consumer keys reports and enables this for all 27 MHz keyboards and for the MX5000. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2019-04-20 19:22:17 +08:00
.report_fixup = hidpp_report_fixup,
.probe = hidpp_probe,
.remove = hidpp_remove,
.raw_event = hidpp_raw_event,
.usage_table = hidpp_usages,
.event = hidpp_event,
.input_configured = hidpp_input_configured,
.input_mapping = hidpp_input_mapping,
.input_mapped = hidpp_input_mapped,
};
module_hid_driver(hidpp_driver);