linux-sg2042/include/linux/usb/chipidea.h

91 lines
2.7 KiB
C
Raw Normal View History

/*
* Platform data for the chipidea USB dual role controller
*/
#ifndef __LINUX_USB_CHIPIDEA_H
#define __LINUX_USB_CHIPIDEA_H
#include <linux/extcon.h>
#include <linux/usb/otg.h>
struct ci_hdrc;
/**
* struct ci_hdrc_cable - structure for external connector cable state tracking
* @state: current state of the line
* @changed: set to true when extcon event happen
* @enabled: set to true if we've enabled the vbus or id interrupt
* @edev: device which generate events
* @ci: driver state of the chipidea device
* @nb: hold event notification callback
* @conn: used for notification registration
*/
struct ci_hdrc_cable {
bool state;
bool changed;
bool enabled;
struct extcon_dev *edev;
struct ci_hdrc *ci;
struct notifier_block nb;
};
struct ci_hdrc_platform_data {
const char *name;
/* offset of the capability registers */
uintptr_t capoffset;
unsigned power_budget;
struct phy *phy;
/* old usb_phy interface */
struct usb_phy *usb_phy;
enum usb_phy_interface phy_mode;
unsigned long flags;
#define CI_HDRC_REGS_SHARED BIT(0)
usb: chipidea: define stream mode disable for both roles The system bus and chipidea IP have different limitations for both host and device mode. For example, with below errata, we need to enable SDIS(Stream Disable Mode) at host mode. But we don't want it for device mode at the same system. TAR 9000378958 Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to Hang on OUT Retry Impacted Configuration: Host mode, all transfer types Description: The host core operating in streaming mode may under run while sending the data packet of an OUT transaction. This under run can occur if there are unexpected system delays in fetching the remaining packet data from memory. The host forces a bad CRC on the packet, the device detects the error and discards the packet. The host then retries a Bulk, Interrupt, or Control transfer if an under run occurs according to the USB specification. During simulations, it was found that the host does not issue the retry of the failed bulk OUT. It does not issue any other transactions except SOF packets that have incorrect frame numbers. The second failure mode occurs if the under run occurs on an ISO OUT transaction and the next ISO transaction is a zero byte packet. The host does not issue any transactions (including SOFs). The device detects a Suspend condition, reverts to full speed, and waits for resume signaling. A third failure mode occurs when the host under runs on an ISO OUT and the next ISO in the schedule is an ISO OUT with two max packets of 1024 bytes each. The host should issue MDATA for the first OUT followed by DATA1 for the second. However, it drops the MDATA transaction, and issues the DATA1 transaction. The system impact of this bug is the same regardless of the failure mode observed. The host core hangs, the ehci_ctrl state machine waits for the protocol engine to send the completion status for the corrupted transaction, which never occurs. No indication is sent to the host controller driver, no register bits change and no interrupts occur. Eventually the requesting application times out. Detailed internal behavior: The EHCI control state machine (ehci_ctrl) in the DMA block is responsible for parsing the schedules and initiating all transactions. The ehci_ctrl state machine passes the transaction details to the protocol block by writing the transaction information in to the TxFIFO. It then asserts the pe_hst_run_pkt signal to inform the host protocol state machine (pe_hst_state) that there is a packet in the TxFIFO. A tag of 0x0 indicates a start of packet with the data providing the following information: 35:32 Tag 31:30 Reserved 29:23 Endpoint (lowest 4 bits) 22:16 Address 15:10 Reserved 9:8 Endpoint speed 7:6 Endpoint type 5:6 Data Toggle 3:0 PID The pe_hst_state reads the packet information and constructs the packet and issues it to the PHY interface. The ehci_ctrl state machine writes the start transaction information in to the TxFIFO as 0x03002910c for the OUT packet that had the under run error. However, it writes 0xC3002910C for the retry of the Out transaction, which is incorrect. The pe_hst_state enters a bus timeout state after sending the bad CRC for the packet that under ran. It then purges any data that was back filled in to the TxFIFO for the packet that under ran. The pe_hst_state machine stops purging the TxFIFO when it is empty or if it reads a location that has a tag of 0x0, indicating a start of packet command. The pe_hst_state reads 0xC3002910C and discards it as it does not decode to a start of packet command. It continues to purge the OUT data that has been pre-buffered for the OUT retry . The pe_hst_state detects the hst_packet_run signal and attempts to read the PID and address information from the TxFIFO. This location has packet data and so does not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD state where the frame_num_counter is updated. The frame_num_counter is updated with the data in the TxFIFO. In this case, the data is incorrect as the ehci_ctrl state machine did not initiate the load. The hst_pe_state machine detects the SOF request signal and sends an SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine waits indefinitely in the run_pkt state waiting for the completion status from pe_hst_state machine, which will never happen. The ISO failure case is similar except that there is no retry for ISO. The ehci_ctrl state machine moves to the next transfer in the periodic schedule. If the under run occurs on the last entry of the periodic list then it moves to the Async schedule. In the case of ISO OUT simulations, the next ISO is a zero byte OUT and again the start of packet command gets corrupted. The TxFIFO is empty when the hst_pe_state attempts to read the Address and PID information as the transaction is a zero byte packet. This results in the hst_pe_state machine staying in the GET_PID state, which means that it does not issue any transactions (including SOFs). The device detects a Suspend condition and reverts to full speed mode and waits for a Resume or Reset signal. The EHCI specification allows a Non-DoubleWord (32 bits) offset to be used as a current offset for Buffer Pointer Page 0 of the qTD. In Non-DoubleWord aligned cases, the core reads the packet data from the AHB memory, performs the alignment operation before writing it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP) is written to the TxFIFO after all the packet data has been written in to the TxFIFO. The alignment function is reset to Idle by the EOP tag. The corruption of the start of packet command arises because the packet buffer for the OUT transaction that under ran is not aligned to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The alignment function is still active when the start packet information is written in to the TxFIFO for the retry of the bulk packet or for the next transaction in the case of an under run on an ISO. This results in the corruption of the start tag and the transaction information. Click for waveform showing the command 0x 0000300291 being written in to the TX FIFO for the Out that under ran. Click for waveform showing the command 0xC3002910C written to the TxFIFO instead of 0x 0000300291 Versions affected: Versions 2.10a and previous versions How discovered: Customer simulation Workaround: 1- The EHCI specification allows a non-DoubleWord offset to be used as a current offset for Buffer Pointer Page 0 of the qTD. However, if a DoubleWord offset is used then this issue does not arise. 2- Use non streaming mode to eliminate under runs. Resolution: The fix involves changes to the traffic state machine in the vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context information by encoding the transaction results on the hst_op_context_update signals at the end of a transaction. The signal hst_op_context_update is added to the traffic state machine, and the tx_fifo_under_ran_r signal is generated if the transaction results in an under run error. Click for waveform The traffic state machine then traverses to the do_eop states if the tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to the TxFIFO as shown in this waveform . The EOP tag resets the align state machine to the Idle state ensuring that the next command written by the echi_ctrl state machine does not get corrupted. File(s) modified: RTL code fixed: ….. Method of reproducing: This failure cannot be reproduced in the current test bench. Date Found: March 2010 Date Fixed: June 2010 Update information: Added the RTL code fix Signed-off-by: Peter Chen <peter.chen@freescale.com>
2014-10-30 09:15:15 +08:00
#define CI_HDRC_DISABLE_DEVICE_STREAMING BIT(1)
#define CI_HDRC_SUPPORTS_RUNTIME_PM BIT(2)
usb: chipidea: define stream mode disable for both roles The system bus and chipidea IP have different limitations for both host and device mode. For example, with below errata, we need to enable SDIS(Stream Disable Mode) at host mode. But we don't want it for device mode at the same system. TAR 9000378958 Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to Hang on OUT Retry Impacted Configuration: Host mode, all transfer types Description: The host core operating in streaming mode may under run while sending the data packet of an OUT transaction. This under run can occur if there are unexpected system delays in fetching the remaining packet data from memory. The host forces a bad CRC on the packet, the device detects the error and discards the packet. The host then retries a Bulk, Interrupt, or Control transfer if an under run occurs according to the USB specification. During simulations, it was found that the host does not issue the retry of the failed bulk OUT. It does not issue any other transactions except SOF packets that have incorrect frame numbers. The second failure mode occurs if the under run occurs on an ISO OUT transaction and the next ISO transaction is a zero byte packet. The host does not issue any transactions (including SOFs). The device detects a Suspend condition, reverts to full speed, and waits for resume signaling. A third failure mode occurs when the host under runs on an ISO OUT and the next ISO in the schedule is an ISO OUT with two max packets of 1024 bytes each. The host should issue MDATA for the first OUT followed by DATA1 for the second. However, it drops the MDATA transaction, and issues the DATA1 transaction. The system impact of this bug is the same regardless of the failure mode observed. The host core hangs, the ehci_ctrl state machine waits for the protocol engine to send the completion status for the corrupted transaction, which never occurs. No indication is sent to the host controller driver, no register bits change and no interrupts occur. Eventually the requesting application times out. Detailed internal behavior: The EHCI control state machine (ehci_ctrl) in the DMA block is responsible for parsing the schedules and initiating all transactions. The ehci_ctrl state machine passes the transaction details to the protocol block by writing the transaction information in to the TxFIFO. It then asserts the pe_hst_run_pkt signal to inform the host protocol state machine (pe_hst_state) that there is a packet in the TxFIFO. A tag of 0x0 indicates a start of packet with the data providing the following information: 35:32 Tag 31:30 Reserved 29:23 Endpoint (lowest 4 bits) 22:16 Address 15:10 Reserved 9:8 Endpoint speed 7:6 Endpoint type 5:6 Data Toggle 3:0 PID The pe_hst_state reads the packet information and constructs the packet and issues it to the PHY interface. The ehci_ctrl state machine writes the start transaction information in to the TxFIFO as 0x03002910c for the OUT packet that had the under run error. However, it writes 0xC3002910C for the retry of the Out transaction, which is incorrect. The pe_hst_state enters a bus timeout state after sending the bad CRC for the packet that under ran. It then purges any data that was back filled in to the TxFIFO for the packet that under ran. The pe_hst_state machine stops purging the TxFIFO when it is empty or if it reads a location that has a tag of 0x0, indicating a start of packet command. The pe_hst_state reads 0xC3002910C and discards it as it does not decode to a start of packet command. It continues to purge the OUT data that has been pre-buffered for the OUT retry . The pe_hst_state detects the hst_packet_run signal and attempts to read the PID and address information from the TxFIFO. This location has packet data and so does not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD state where the frame_num_counter is updated. The frame_num_counter is updated with the data in the TxFIFO. In this case, the data is incorrect as the ehci_ctrl state machine did not initiate the load. The hst_pe_state machine detects the SOF request signal and sends an SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine waits indefinitely in the run_pkt state waiting for the completion status from pe_hst_state machine, which will never happen. The ISO failure case is similar except that there is no retry for ISO. The ehci_ctrl state machine moves to the next transfer in the periodic schedule. If the under run occurs on the last entry of the periodic list then it moves to the Async schedule. In the case of ISO OUT simulations, the next ISO is a zero byte OUT and again the start of packet command gets corrupted. The TxFIFO is empty when the hst_pe_state attempts to read the Address and PID information as the transaction is a zero byte packet. This results in the hst_pe_state machine staying in the GET_PID state, which means that it does not issue any transactions (including SOFs). The device detects a Suspend condition and reverts to full speed mode and waits for a Resume or Reset signal. The EHCI specification allows a Non-DoubleWord (32 bits) offset to be used as a current offset for Buffer Pointer Page 0 of the qTD. In Non-DoubleWord aligned cases, the core reads the packet data from the AHB memory, performs the alignment operation before writing it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP) is written to the TxFIFO after all the packet data has been written in to the TxFIFO. The alignment function is reset to Idle by the EOP tag. The corruption of the start of packet command arises because the packet buffer for the OUT transaction that under ran is not aligned to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The alignment function is still active when the start packet information is written in to the TxFIFO for the retry of the bulk packet or for the next transaction in the case of an under run on an ISO. This results in the corruption of the start tag and the transaction information. Click for waveform showing the command 0x 0000300291 being written in to the TX FIFO for the Out that under ran. Click for waveform showing the command 0xC3002910C written to the TxFIFO instead of 0x 0000300291 Versions affected: Versions 2.10a and previous versions How discovered: Customer simulation Workaround: 1- The EHCI specification allows a non-DoubleWord offset to be used as a current offset for Buffer Pointer Page 0 of the qTD. However, if a DoubleWord offset is used then this issue does not arise. 2- Use non streaming mode to eliminate under runs. Resolution: The fix involves changes to the traffic state machine in the vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context information by encoding the transaction results on the hst_op_context_update signals at the end of a transaction. The signal hst_op_context_update is added to the traffic state machine, and the tx_fifo_under_ran_r signal is generated if the transaction results in an under run error. Click for waveform The traffic state machine then traverses to the do_eop states if the tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to the TxFIFO as shown in this waveform . The EOP tag resets the align state machine to the Idle state ensuring that the next command written by the echi_ctrl state machine does not get corrupted. File(s) modified: RTL code fixed: ….. Method of reproducing: This failure cannot be reproduced in the current test bench. Date Found: March 2010 Date Fixed: June 2010 Update information: Added the RTL code fix Signed-off-by: Peter Chen <peter.chen@freescale.com>
2014-10-30 09:15:15 +08:00
#define CI_HDRC_DISABLE_HOST_STREAMING BIT(3)
#define CI_HDRC_DISABLE_STREAMING (CI_HDRC_DISABLE_DEVICE_STREAMING | \
CI_HDRC_DISABLE_HOST_STREAMING)
/*
* Only set it when DCCPARAMS.DC==1 and DCCPARAMS.HC==1,
* but otg is not supported (no register otgsc).
*/
#define CI_HDRC_DUAL_ROLE_NOT_OTG BIT(4)
#define CI_HDRC_IMX28_WRITE_FIX BIT(5)
#define CI_HDRC_FORCE_FULLSPEED BIT(6)
#define CI_HDRC_TURN_VBUS_EARLY_ON BIT(7)
#define CI_HDRC_SET_NON_ZERO_TTHA BIT(8)
#define CI_HDRC_OVERRIDE_AHB_BURST BIT(9)
#define CI_HDRC_OVERRIDE_TX_BURST BIT(10)
#define CI_HDRC_OVERRIDE_RX_BURST BIT(11)
#define CI_HDRC_OVERRIDE_PHY_CONTROL BIT(12) /* Glue layer manages phy */
enum usb_dr_mode dr_mode;
#define CI_HDRC_CONTROLLER_RESET_EVENT 0
#define CI_HDRC_CONTROLLER_STOPPED_EVENT 1
void (*notify_event) (struct ci_hdrc *ci, unsigned event);
struct regulator *reg_vbus;
struct usb_otg_caps ci_otg_caps;
bool tpl_support;
/* interrupt threshold setting */
u32 itc_setting;
u32 ahb_burst_config;
u32 tx_burst_size;
u32 rx_burst_size;
/* VBUS and ID signal state tracking, using extcon framework */
struct ci_hdrc_cable vbus_extcon;
struct ci_hdrc_cable id_extcon;
u32 phy_clkgate_delay_us;
};
/* Default offset of capability registers */
#define DEF_CAPOFFSET 0x100
/* Add ci hdrc device */
struct platform_device *ci_hdrc_add_device(struct device *dev,
struct resource *res, int nres,
struct ci_hdrc_platform_data *platdata);
/* Remove ci hdrc device */
void ci_hdrc_remove_device(struct platform_device *pdev);
#endif