linux-sg2042/include/linux/i2c/bfin_twi.h

146 lines
4.5 KiB
C
Raw Normal View History

/*
* i2c-bfin-twi.h - interface to ADI TWI controller
*
* Copyright 2005-2014 Analog Devices Inc.
*
* Licensed under the GPL-2 or later.
*/
#ifndef __I2C_BFIN_TWI_H__
#define __I2C_BFIN_TWI_H__
#include <linux/types.h>
#include <linux/i2c.h>
/*
* ADI twi registers layout
*/
struct bfin_twi_regs {
u16 clkdiv;
u16 dummy1;
u16 control;
u16 dummy2;
u16 slave_ctl;
u16 dummy3;
u16 slave_stat;
u16 dummy4;
u16 slave_addr;
u16 dummy5;
u16 master_ctl;
u16 dummy6;
u16 master_stat;
u16 dummy7;
u16 master_addr;
u16 dummy8;
u16 int_stat;
u16 dummy9;
u16 int_mask;
u16 dummy10;
u16 fifo_ctl;
u16 dummy11;
u16 fifo_stat;
u16 dummy12;
u32 __pad[20];
u16 xmt_data8;
u16 dummy13;
u16 xmt_data16;
u16 dummy14;
u16 rcv_data8;
u16 dummy15;
u16 rcv_data16;
u16 dummy16;
};
struct bfin_twi_iface {
int irq;
spinlock_t lock;
char read_write;
u8 command;
u8 *transPtr;
int readNum;
int writeNum;
int cur_mode;
int manual_stop;
int result;
struct i2c_adapter adap;
struct completion complete;
struct i2c_msg *pmsg;
int msg_num;
int cur_msg;
u16 saved_clkdiv;
u16 saved_control;
struct bfin_twi_regs __iomem *regs_base;
};
/* ******************** TWO-WIRE INTERFACE (TWI) MASKS ********************/
/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y); ) */
#define CLKLOW(x) ((x) & 0xFF) /* Periods Clock Is Held Low */
#define CLKHI(y) (((y)&0xFF)<<0x8) /* Periods Before New Clock Low */
/* TWI_PRESCALE Masks */
#define PRESCALE 0x007F /* SCLKs Per Internal Time Reference (10MHz) */
#define TWI_ENA 0x0080 /* TWI Enable */
#define SCCB 0x0200 /* SCCB Compatibility Enable */
/* TWI_SLAVE_CTL Masks */
#define SEN 0x0001 /* Slave Enable */
#define SADD_LEN 0x0002 /* Slave Address Length */
#define STDVAL 0x0004 /* Slave Transmit Data Valid */
#define NAK 0x0008 /* NAK Generated At Conclusion Of Transfer */
#define GEN 0x0010 /* General Call Address Matching Enabled */
/* TWI_SLAVE_STAT Masks */
#define SDIR 0x0001 /* Slave Transfer Direction (RX/TX*) */
#define GCALL 0x0002 /* General Call Indicator */
/* TWI_MASTER_CTL Masks */
#define MEN 0x0001 /* Master Mode Enable */
#define MADD_LEN 0x0002 /* Master Address Length */
#define MDIR 0x0004 /* Master Transmit Direction (RX/TX*) */
#define FAST 0x0008 /* Use Fast Mode Timing Specs */
#define STOP 0x0010 /* Issue Stop Condition */
#define RSTART 0x0020 /* Repeat Start or Stop* At End Of Transfer */
#define DCNT 0x3FC0 /* Data Bytes To Transfer */
#define SDAOVR 0x4000 /* Serial Data Override */
#define SCLOVR 0x8000 /* Serial Clock Override */
/* TWI_MASTER_STAT Masks */
#define MPROG 0x0001 /* Master Transfer In Progress */
#define LOSTARB 0x0002 /* Lost Arbitration Indicator (Xfer Aborted) */
#define ANAK 0x0004 /* Address Not Acknowledged */
#define DNAK 0x0008 /* Data Not Acknowledged */
#define BUFRDERR 0x0010 /* Buffer Read Error */
#define BUFWRERR 0x0020 /* Buffer Write Error */
#define SDASEN 0x0040 /* Serial Data Sense */
#define SCLSEN 0x0080 /* Serial Clock Sense */
#define BUSBUSY 0x0100 /* Bus Busy Indicator */
/* TWI_INT_SRC and TWI_INT_ENABLE Masks */
#define SINIT 0x0001 /* Slave Transfer Initiated */
#define SCOMP 0x0002 /* Slave Transfer Complete */
#define SERR 0x0004 /* Slave Transfer Error */
#define SOVF 0x0008 /* Slave Overflow */
#define MCOMP 0x0010 /* Master Transfer Complete */
#define MERR 0x0020 /* Master Transfer Error */
#define XMTSERV 0x0040 /* Transmit FIFO Service */
#define RCVSERV 0x0080 /* Receive FIFO Service */
/* TWI_FIFO_CTRL Masks */
#define XMTFLUSH 0x0001 /* Transmit Buffer Flush */
#define RCVFLUSH 0x0002 /* Receive Buffer Flush */
#define XMTINTLEN 0x0004 /* Transmit Buffer Interrupt Length */
#define RCVINTLEN 0x0008 /* Receive Buffer Interrupt Length */
/* TWI_FIFO_STAT Masks */
#define XMTSTAT 0x0003 /* Transmit FIFO Status */
#define XMT_EMPTY 0x0000 /* Transmit FIFO Empty */
#define XMT_HALF 0x0001 /* Transmit FIFO Has 1 Byte To Write */
#define XMT_FULL 0x0003 /* Transmit FIFO Full (2 Bytes To Write) */
#define RCVSTAT 0x000C /* Receive FIFO Status */
#define RCV_EMPTY 0x0000 /* Receive FIFO Empty */
#define RCV_HALF 0x0004 /* Receive FIFO Has 1 Byte To Read */
#define RCV_FULL 0x000C /* Receive FIFO Full (2 Bytes To Read) */
#endif