linux-sg2042/drivers/hwmon/ds1621.c

/*
 * ds1621.c - Part of lm_sensors, Linux kernel modules for hardware
 *	      monitoring
 * Christian W. Zuckschwerdt  <zany@triq.net>  2000-11-23
 * based on lm75.c by Frodo Looijaard <frodol@dds.nl>
 * Ported to Linux 2.6 by Aurelien Jarno <aurelien@aurel32.net> with
 * the help of Jean Delvare <khali@linux-fr.org>
 *
 * The DS1621 device is a digital temperature/thermometer with 9-bit
 * resolution, a thermal alarm output (Tout), and user-defined minimum
 * and maximum temperature thresholds (TH and TL).
 *
 * The DS1625 and DS1721 are pin compatible with the DS1621 and similar
 * in operation, with slight variations as noted in the device
 * datasheets (please refer to www.maximintegrated.com for specific
 * device information).
 *
 * Since the DS1621 was the first chipset supported by this driver,
 * most comments will refer to this chipset, but are actually general
 * and concern all supported chipsets, unless mentioned otherwise.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <linux/sysfs.h>
#include <linux/kernel.h>

/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
					0x4d, 0x4e, 0x4f, I2C_CLIENT_END };

/* Supported devices */
enum chips { ds1621, ds1625, ds1721 };

/* Insmod parameters */
static int polarity = -1;
module_param(polarity, int, 0);
MODULE_PARM_DESC(polarity, "Output's polarity: 0 = active high, 1 = active low");

/*
 * The Configuration/Status register
 *
 * - DS1621:
 *   7    6    5    4    3    2    1    0
 * |Done|THF |TLF |NVB | X  | X  |POL |1SHOT|
 *
 * - DS1625:
 *   7    6    5    4    3    2    1    0
 * |Done|THF |TLF |NVB | 1  | 0  |POL |1SHOT|
 *
 * - DS1721:
 *   7    6    5    4    3    2    1    0
 * |Done| X  | X  | U  | R1 | R0 |POL |1SHOT|
 *
 * Where:
 * - 'X' is Reserved
 * - 'U' is Undefined
 */
#define DS1621_REG_CONFIG_NVB		0x10
#define DS1621_REG_CONFIG_RESOL		0x0C
#define DS1621_REG_CONFIG_POLARITY	0x02
#define DS1621_REG_CONFIG_1SHOT		0x01
#define DS1621_REG_CONFIG_DONE		0x80

#define DS1621_REG_CONFIG_RESOL_SHIFT	2

/* ds1721 conversion rates: {C/LSB, time(ms), resolution bit setting} */
static const unsigned short ds1721_convrates[] = {
	94,	/*  9-bits (0.5,  93.75, RES[0..1] = 0 */
	188,	/* 10-bits (0.25, 187.5, RES[0..1] = 1 */
	375,	/* 11-bits (0.125,  375, RES[0..1] = 2 */
	750,	/* 12-bits (0.0625, 750, RES[0..1] = 3 */
};

#define DS1621_CONVERSION_MAX	750
#define DS1625_CONVERSION_MAX	500

#define DS1621_TEMP_MAX	125000
#define DS1621_TEMP_MIN	(-55000)

/* The DS1621 temperature registers */
static const u8 DS1621_REG_TEMP[3] = {
	0xAA,		/* input, word, RO */
	0xA2,		/* min, word, RW */
	0xA1,		/* max, word, RW */
};
#define DS1621_REG_CONF			0xAC /* byte, RW */
#define DS1621_COM_START		0xEE /* no data */
#define DS1721_COM_START		0x51 /* no data */
#define DS1621_COM_STOP			0x22 /* no data */

/* The DS1621 configuration register */
#define DS1621_ALARM_TEMP_HIGH		0x40
#define DS1621_ALARM_TEMP_LOW		0x20

/* Conversions */
#define ALARMS_FROM_REG(val) ((val) & \
			(DS1621_ALARM_TEMP_HIGH | DS1621_ALARM_TEMP_LOW))

/* Each client has this additional data */
struct ds1621_data {
	struct device *hwmon_dev;
	struct mutex update_lock;
	char valid;			/* !=0 if following fields are valid */
	unsigned long last_updated;	/* In jiffies */
	enum chips kind;		/* device type */

	u16 temp[3];			/* Register values, word */
	u8 conf;			/* Register encoding, combined */
	u16 update_interval;		/* Conversion rate in milliseconds */
};

static inline int DS1621_TEMP_FROM_REG(u16 reg)
{
	return DIV_ROUND_CLOSEST(((s16)reg / 16) * 625, 10);
}

/*
 * TEMP: 0.001C/bit (-55C to +125C)
 * REG:
 *  - 1621, 1625: x = 0.5C
 *  - 1721:       x = 0.0625C
 * Assume highest resolution and let the bits fall where they may..
 */
static inline u16 DS1621_TEMP_TO_REG(long temp)
{
	int ntemp = clamp_val(temp, DS1621_TEMP_MIN, DS1621_TEMP_MAX);
	ntemp += (ntemp < 0 ? -31 : 31);
	ntemp = DIV_ROUND_CLOSEST(ntemp * 10, 625) << 4;
	return (u16)ntemp;
}

static void ds1621_init_client(struct i2c_client *client)
{
	u8 conf, new_conf, sreg, resol;
	struct ds1621_data *data = i2c_get_clientdata(client);

	new_conf = conf = i2c_smbus_read_byte_data(client, DS1621_REG_CONF);
	/* switch to continuous conversion mode */
	new_conf &= ~DS1621_REG_CONFIG_1SHOT;

	/* setup output polarity */
	if (polarity == 0)
		new_conf &= ~DS1621_REG_CONFIG_POLARITY;
	else if (polarity == 1)
		new_conf |= DS1621_REG_CONFIG_POLARITY;

	if (conf != new_conf)
		i2c_smbus_write_byte_data(client, DS1621_REG_CONF, new_conf);

	switch (data->kind) {
	case ds1625:
		data->update_interval = DS1625_CONVERSION_MAX;
		sreg = DS1621_COM_START;
		break;
	case ds1721:
		resol = (new_conf & DS1621_REG_CONFIG_RESOL) >>
			 DS1621_REG_CONFIG_RESOL_SHIFT;
		data->update_interval = ds1721_convrates[resol];
		sreg = DS1721_COM_START;
		break;
	default:
		data->update_interval = DS1621_CONVERSION_MAX;
		sreg = DS1621_COM_START;
		break;
	}

	/* start conversion */
	i2c_smbus_write_byte(client, sreg);
}

static struct ds1621_data *ds1621_update_client(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct ds1621_data *data = i2c_get_clientdata(client);
	u8 new_conf;

	mutex_lock(&data->update_lock);

	if (time_after(jiffies, data->last_updated + data->update_interval) ||
	    !data->valid) {
		int i;

		dev_dbg(&client->dev, "Starting ds1621 update\n");

		data->conf = i2c_smbus_read_byte_data(client, DS1621_REG_CONF);

		for (i = 0; i < ARRAY_SIZE(data->temp); i++)
			data->temp[i] = i2c_smbus_read_word_swapped(client,
							 DS1621_REG_TEMP[i]);

		/* reset alarms if necessary */
		new_conf = data->conf;
		if (data->temp[0] > data->temp[1])	/* input > min */
			new_conf &= ~DS1621_ALARM_TEMP_LOW;
		if (data->temp[0] < data->temp[2])	/* input < max */
			new_conf &= ~DS1621_ALARM_TEMP_HIGH;
		if (data->conf != new_conf)
			i2c_smbus_write_byte_data(client, DS1621_REG_CONF,
						  new_conf);

		data->last_updated = jiffies;
		data->valid = 1;
	}

	mutex_unlock(&data->update_lock);

	return data;
}

static ssize_t show_temp(struct device *dev, struct device_attribute *da,
			 char *buf)
{
	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
	struct ds1621_data *data = ds1621_update_client(dev);
	return sprintf(buf, "%d\n",
		       DS1621_TEMP_FROM_REG(data->temp[attr->index]));
}

static ssize_t set_temp(struct device *dev, struct device_attribute *da,
			const char *buf, size_t count)
{
	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
	struct i2c_client *client = to_i2c_client(dev);
	struct ds1621_data *data = i2c_get_clientdata(client);
	long val;
	int err;

	err = kstrtol(buf, 10, &val);
	if (err)
		return err;

	mutex_lock(&data->update_lock);
	data->temp[attr->index] = DS1621_TEMP_TO_REG(val);
	i2c_smbus_write_word_swapped(client, DS1621_REG_TEMP[attr->index],
				     data->temp[attr->index]);
	mutex_unlock(&data->update_lock);
	return count;
}

static ssize_t show_alarms(struct device *dev, struct device_attribute *da,
			   char *buf)
{
	struct ds1621_data *data = ds1621_update_client(dev);
	return sprintf(buf, "%d\n", ALARMS_FROM_REG(data->conf));
}

static ssize_t show_alarm(struct device *dev, struct device_attribute *da,
			  char *buf)
{
	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
	struct ds1621_data *data = ds1621_update_client(dev);
	return sprintf(buf, "%d\n", !!(data->conf & attr->index));
}

static ssize_t show_convrate(struct device *dev, struct device_attribute *da,
			  char *buf)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct ds1621_data *data = i2c_get_clientdata(client);
	return scnprintf(buf, PAGE_SIZE, "%hu\n", data->update_interval);
}

static ssize_t set_convrate(struct device *dev, struct device_attribute *da,
			    const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct ds1621_data *data = i2c_get_clientdata(client);
	unsigned long convrate;
	s32 err;
	int resol = 0;

	err = kstrtoul(buf, 10, &convrate);
	if (err)
		return err;

	/* Convert rate into resolution bits */
	while (resol < (ARRAY_SIZE(ds1721_convrates) - 1) &&
	       convrate > ds1721_convrates[resol])
		resol++;

	mutex_lock(&data->update_lock);
	data->conf = i2c_smbus_read_byte_data(client, DS1621_REG_CONF);
	data->conf &= ~DS1621_REG_CONFIG_RESOL;
	data->conf |= (resol << DS1621_REG_CONFIG_RESOL_SHIFT);
	i2c_smbus_write_byte_data(client, DS1621_REG_CONF, data->conf);
	data->update_interval = ds1721_convrates[resol];
	mutex_unlock(&data->update_lock);

	return count;
}

static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
static DEVICE_ATTR(update_interval, S_IWUSR | S_IRUGO, show_convrate,
		   set_convrate);

static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp, set_temp, 1);
static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp, set_temp, 2);
static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL,
		DS1621_ALARM_TEMP_LOW);
static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL,
		DS1621_ALARM_TEMP_HIGH);

static struct attribute *ds1621_attributes[] = {
	&sensor_dev_attr_temp1_input.dev_attr.attr,
	&sensor_dev_attr_temp1_min.dev_attr.attr,
	&sensor_dev_attr_temp1_max.dev_attr.attr,
	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
	&dev_attr_alarms.attr,
	&dev_attr_update_interval.attr,
	NULL
};

static umode_t ds1621_attribute_visible(struct kobject *kobj,
					struct attribute *attr, int index)
{
	struct device *dev = container_of(kobj, struct device, kobj);
	struct i2c_client *client = to_i2c_client(dev);
	struct ds1621_data *data = i2c_get_clientdata(client);

	if (attr == &dev_attr_update_interval.attr)
		if (data->kind != ds1721)
			/* shhh, we're hiding update_interval */
			return 0;
	return attr->mode;
}

static const struct attribute_group ds1621_group = {
	.attrs = ds1621_attributes,
	.is_visible = ds1621_attribute_visible
};


/* Return 0 if detection is successful, -ENODEV otherwise */
static int ds1621_detect(struct i2c_client *client,
			 struct i2c_board_info *info)
{
	struct i2c_adapter *adapter = client->adapter;
	int conf, temp;
	int i;

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA
				     | I2C_FUNC_SMBUS_WORD_DATA
				     | I2C_FUNC_SMBUS_WRITE_BYTE))
		return -ENODEV;

	/*
	 * Now, we do the remaining detection. It is lousy.
	 *
	 * The NVB bit should be low if no EEPROM write has been requested
	 * during the latest 10ms, which is highly improbable in our case.
	 */
	conf = i2c_smbus_read_byte_data(client, DS1621_REG_CONF);
	if (conf < 0 || conf & DS1621_REG_CONFIG_NVB)
		return -ENODEV;
	/* The 7 lowest bits of a temperature should always be 0. */
	for (i = 0; i < ARRAY_SIZE(DS1621_REG_TEMP); i++) {
		temp = i2c_smbus_read_word_data(client, DS1621_REG_TEMP[i]);
		if (temp < 0 || (temp & 0x7f00))
			return -ENODEV;
	}

	strlcpy(info->type, "ds1621", I2C_NAME_SIZE);

	return 0;
}

static int ds1621_probe(struct i2c_client *client,
			const struct i2c_device_id *id)
{
	struct ds1621_data *data;
	int err;

	data = devm_kzalloc(&client->dev, sizeof(struct ds1621_data),
			    GFP_KERNEL);
	if (!data)
		return -ENOMEM;

	i2c_set_clientdata(client, data);
	mutex_init(&data->update_lock);

	data->kind = id->driver_data;

	/* Initialize the DS1621 chip */
	ds1621_init_client(client);

	/* Register sysfs hooks */
	err = sysfs_create_group(&client->dev.kobj, &ds1621_group);
	if (err)
		return err;

	data->hwmon_dev = hwmon_device_register(&client->dev);
	if (IS_ERR(data->hwmon_dev)) {
		err = PTR_ERR(data->hwmon_dev);
		goto exit_remove_files;
	}

	return 0;

 exit_remove_files:
	sysfs_remove_group(&client->dev.kobj, &ds1621_group);
	return err;
}

static int ds1621_remove(struct i2c_client *client)
{
	struct ds1621_data *data = i2c_get_clientdata(client);

	hwmon_device_unregister(data->hwmon_dev);
	sysfs_remove_group(&client->dev.kobj, &ds1621_group);

	return 0;
}

static const struct i2c_device_id ds1621_id[] = {
	{ "ds1621", ds1621 },
	{ "ds1625", ds1625 },
	{ "ds1721", ds1721 },
	{ }
};
MODULE_DEVICE_TABLE(i2c, ds1621_id);

/* This is the driver that will be inserted */
static struct i2c_driver ds1621_driver = {
	.class		= I2C_CLASS_HWMON,
	.driver = {
		.name	= "ds1621",
	},
	.probe		= ds1621_probe,
	.remove		= ds1621_remove,
	.id_table	= ds1621_id,
	.detect		= ds1621_detect,
	.address_list	= normal_i2c,
};

module_i2c_driver(ds1621_driver);

MODULE_AUTHOR("Christian W. Zuckschwerdt <zany@triq.net>");
MODULE_DESCRIPTION("DS1621 driver");
MODULE_LICENSE("GPL");