649 lines
16 KiB
C
649 lines
16 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Analog Devices AD7768-1 SPI ADC driver
|
|
*
|
|
* Copyright 2017 Analog Devices Inc.
|
|
*/
|
|
#include <linux/bitfield.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/device.h>
|
|
#include <linux/err.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/sysfs.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#include <linux/iio/buffer.h>
|
|
#include <linux/iio/iio.h>
|
|
#include <linux/iio/sysfs.h>
|
|
#include <linux/iio/trigger.h>
|
|
#include <linux/iio/triggered_buffer.h>
|
|
#include <linux/iio/trigger_consumer.h>
|
|
|
|
/* AD7768 registers definition */
|
|
#define AD7768_REG_CHIP_TYPE 0x3
|
|
#define AD7768_REG_PROD_ID_L 0x4
|
|
#define AD7768_REG_PROD_ID_H 0x5
|
|
#define AD7768_REG_CHIP_GRADE 0x6
|
|
#define AD7768_REG_SCRATCH_PAD 0x0A
|
|
#define AD7768_REG_VENDOR_L 0x0C
|
|
#define AD7768_REG_VENDOR_H 0x0D
|
|
#define AD7768_REG_INTERFACE_FORMAT 0x14
|
|
#define AD7768_REG_POWER_CLOCK 0x15
|
|
#define AD7768_REG_ANALOG 0x16
|
|
#define AD7768_REG_ANALOG2 0x17
|
|
#define AD7768_REG_CONVERSION 0x18
|
|
#define AD7768_REG_DIGITAL_FILTER 0x19
|
|
#define AD7768_REG_SINC3_DEC_RATE_MSB 0x1A
|
|
#define AD7768_REG_SINC3_DEC_RATE_LSB 0x1B
|
|
#define AD7768_REG_DUTY_CYCLE_RATIO 0x1C
|
|
#define AD7768_REG_SYNC_RESET 0x1D
|
|
#define AD7768_REG_GPIO_CONTROL 0x1E
|
|
#define AD7768_REG_GPIO_WRITE 0x1F
|
|
#define AD7768_REG_GPIO_READ 0x20
|
|
#define AD7768_REG_OFFSET_HI 0x21
|
|
#define AD7768_REG_OFFSET_MID 0x22
|
|
#define AD7768_REG_OFFSET_LO 0x23
|
|
#define AD7768_REG_GAIN_HI 0x24
|
|
#define AD7768_REG_GAIN_MID 0x25
|
|
#define AD7768_REG_GAIN_LO 0x26
|
|
#define AD7768_REG_SPI_DIAG_ENABLE 0x28
|
|
#define AD7768_REG_ADC_DIAG_ENABLE 0x29
|
|
#define AD7768_REG_DIG_DIAG_ENABLE 0x2A
|
|
#define AD7768_REG_ADC_DATA 0x2C
|
|
#define AD7768_REG_MASTER_STATUS 0x2D
|
|
#define AD7768_REG_SPI_DIAG_STATUS 0x2E
|
|
#define AD7768_REG_ADC_DIAG_STATUS 0x2F
|
|
#define AD7768_REG_DIG_DIAG_STATUS 0x30
|
|
#define AD7768_REG_MCLK_COUNTER 0x31
|
|
|
|
/* AD7768_REG_POWER_CLOCK */
|
|
#define AD7768_PWR_MCLK_DIV_MSK GENMASK(5, 4)
|
|
#define AD7768_PWR_MCLK_DIV(x) FIELD_PREP(AD7768_PWR_MCLK_DIV_MSK, x)
|
|
#define AD7768_PWR_PWRMODE_MSK GENMASK(1, 0)
|
|
#define AD7768_PWR_PWRMODE(x) FIELD_PREP(AD7768_PWR_PWRMODE_MSK, x)
|
|
|
|
/* AD7768_REG_DIGITAL_FILTER */
|
|
#define AD7768_DIG_FIL_FIL_MSK GENMASK(6, 4)
|
|
#define AD7768_DIG_FIL_FIL(x) FIELD_PREP(AD7768_DIG_FIL_FIL_MSK, x)
|
|
#define AD7768_DIG_FIL_DEC_MSK GENMASK(2, 0)
|
|
#define AD7768_DIG_FIL_DEC_RATE(x) FIELD_PREP(AD7768_DIG_FIL_DEC_MSK, x)
|
|
|
|
/* AD7768_REG_CONVERSION */
|
|
#define AD7768_CONV_MODE_MSK GENMASK(2, 0)
|
|
#define AD7768_CONV_MODE(x) FIELD_PREP(AD7768_CONV_MODE_MSK, x)
|
|
|
|
#define AD7768_RD_FLAG_MSK(x) (BIT(6) | ((x) & 0x3F))
|
|
#define AD7768_WR_FLAG_MSK(x) ((x) & 0x3F)
|
|
|
|
enum ad7768_conv_mode {
|
|
AD7768_CONTINUOUS,
|
|
AD7768_ONE_SHOT,
|
|
AD7768_SINGLE,
|
|
AD7768_PERIODIC,
|
|
AD7768_STANDBY
|
|
};
|
|
|
|
enum ad7768_pwrmode {
|
|
AD7768_ECO_MODE = 0,
|
|
AD7768_MED_MODE = 2,
|
|
AD7768_FAST_MODE = 3
|
|
};
|
|
|
|
enum ad7768_mclk_div {
|
|
AD7768_MCLK_DIV_16,
|
|
AD7768_MCLK_DIV_8,
|
|
AD7768_MCLK_DIV_4,
|
|
AD7768_MCLK_DIV_2
|
|
};
|
|
|
|
enum ad7768_dec_rate {
|
|
AD7768_DEC_RATE_32 = 0,
|
|
AD7768_DEC_RATE_64 = 1,
|
|
AD7768_DEC_RATE_128 = 2,
|
|
AD7768_DEC_RATE_256 = 3,
|
|
AD7768_DEC_RATE_512 = 4,
|
|
AD7768_DEC_RATE_1024 = 5,
|
|
AD7768_DEC_RATE_8 = 9,
|
|
AD7768_DEC_RATE_16 = 10
|
|
};
|
|
|
|
struct ad7768_clk_configuration {
|
|
enum ad7768_mclk_div mclk_div;
|
|
enum ad7768_dec_rate dec_rate;
|
|
unsigned int clk_div;
|
|
enum ad7768_pwrmode pwrmode;
|
|
};
|
|
|
|
static const struct ad7768_clk_configuration ad7768_clk_config[] = {
|
|
{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_8, 16, AD7768_FAST_MODE },
|
|
{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_16, 32, AD7768_FAST_MODE },
|
|
{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_32, 64, AD7768_FAST_MODE },
|
|
{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_64, 128, AD7768_FAST_MODE },
|
|
{ AD7768_MCLK_DIV_2, AD7768_DEC_RATE_128, 256, AD7768_FAST_MODE },
|
|
{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_128, 512, AD7768_MED_MODE },
|
|
{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_256, 1024, AD7768_MED_MODE },
|
|
{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_512, 2048, AD7768_MED_MODE },
|
|
{ AD7768_MCLK_DIV_4, AD7768_DEC_RATE_1024, 4096, AD7768_MED_MODE },
|
|
{ AD7768_MCLK_DIV_8, AD7768_DEC_RATE_1024, 8192, AD7768_MED_MODE },
|
|
{ AD7768_MCLK_DIV_16, AD7768_DEC_RATE_1024, 16384, AD7768_ECO_MODE },
|
|
};
|
|
|
|
static const struct iio_chan_spec ad7768_channels[] = {
|
|
{
|
|
.type = IIO_VOLTAGE,
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
|
|
.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
|
|
.indexed = 1,
|
|
.channel = 0,
|
|
.scan_index = 0,
|
|
.scan_type = {
|
|
.sign = 'u',
|
|
.realbits = 24,
|
|
.storagebits = 32,
|
|
.shift = 8,
|
|
.endianness = IIO_BE,
|
|
},
|
|
},
|
|
};
|
|
|
|
struct ad7768_state {
|
|
struct spi_device *spi;
|
|
struct regulator *vref;
|
|
struct mutex lock;
|
|
struct clk *mclk;
|
|
unsigned int mclk_freq;
|
|
unsigned int samp_freq;
|
|
struct completion completion;
|
|
struct iio_trigger *trig;
|
|
struct gpio_desc *gpio_sync_in;
|
|
/*
|
|
* DMA (thus cache coherency maintenance) requires the
|
|
* transfer buffers to live in their own cache lines.
|
|
*/
|
|
union {
|
|
__be32 d32;
|
|
u8 d8[2];
|
|
} data ____cacheline_aligned;
|
|
};
|
|
|
|
static int ad7768_spi_reg_read(struct ad7768_state *st, unsigned int addr,
|
|
unsigned int len)
|
|
{
|
|
unsigned int shift;
|
|
int ret;
|
|
|
|
shift = 32 - (8 * len);
|
|
st->data.d8[0] = AD7768_RD_FLAG_MSK(addr);
|
|
|
|
ret = spi_write_then_read(st->spi, st->data.d8, 1,
|
|
&st->data.d32, len);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return (be32_to_cpu(st->data.d32) >> shift);
|
|
}
|
|
|
|
static int ad7768_spi_reg_write(struct ad7768_state *st,
|
|
unsigned int addr,
|
|
unsigned int val)
|
|
{
|
|
st->data.d8[0] = AD7768_WR_FLAG_MSK(addr);
|
|
st->data.d8[1] = val & 0xFF;
|
|
|
|
return spi_write(st->spi, st->data.d8, 2);
|
|
}
|
|
|
|
static int ad7768_set_mode(struct ad7768_state *st,
|
|
enum ad7768_conv_mode mode)
|
|
{
|
|
int regval;
|
|
|
|
regval = ad7768_spi_reg_read(st, AD7768_REG_CONVERSION, 1);
|
|
if (regval < 0)
|
|
return regval;
|
|
|
|
regval &= ~AD7768_CONV_MODE_MSK;
|
|
regval |= AD7768_CONV_MODE(mode);
|
|
|
|
return ad7768_spi_reg_write(st, AD7768_REG_CONVERSION, regval);
|
|
}
|
|
|
|
static int ad7768_scan_direct(struct iio_dev *indio_dev)
|
|
{
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
int readval, ret;
|
|
|
|
reinit_completion(&st->completion);
|
|
|
|
ret = ad7768_set_mode(st, AD7768_ONE_SHOT);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = wait_for_completion_timeout(&st->completion,
|
|
msecs_to_jiffies(1000));
|
|
if (!ret)
|
|
return -ETIMEDOUT;
|
|
|
|
readval = ad7768_spi_reg_read(st, AD7768_REG_ADC_DATA, 3);
|
|
if (readval < 0)
|
|
return readval;
|
|
/*
|
|
* Any SPI configuration of the AD7768-1 can only be
|
|
* performed in continuous conversion mode.
|
|
*/
|
|
ret = ad7768_set_mode(st, AD7768_CONTINUOUS);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return readval;
|
|
}
|
|
|
|
static int ad7768_reg_access(struct iio_dev *indio_dev,
|
|
unsigned int reg,
|
|
unsigned int writeval,
|
|
unsigned int *readval)
|
|
{
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
int ret;
|
|
|
|
mutex_lock(&st->lock);
|
|
if (readval) {
|
|
ret = ad7768_spi_reg_read(st, reg, 1);
|
|
if (ret < 0)
|
|
goto err_unlock;
|
|
*readval = ret;
|
|
ret = 0;
|
|
} else {
|
|
ret = ad7768_spi_reg_write(st, reg, writeval);
|
|
}
|
|
err_unlock:
|
|
mutex_unlock(&st->lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ad7768_set_dig_fil(struct ad7768_state *st,
|
|
enum ad7768_dec_rate dec_rate)
|
|
{
|
|
unsigned int mode;
|
|
int ret;
|
|
|
|
if (dec_rate == AD7768_DEC_RATE_8 || dec_rate == AD7768_DEC_RATE_16)
|
|
mode = AD7768_DIG_FIL_FIL(dec_rate);
|
|
else
|
|
mode = AD7768_DIG_FIL_DEC_RATE(dec_rate);
|
|
|
|
ret = ad7768_spi_reg_write(st, AD7768_REG_DIGITAL_FILTER, mode);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* A sync-in pulse is required every time the filter dec rate changes */
|
|
gpiod_set_value(st->gpio_sync_in, 1);
|
|
gpiod_set_value(st->gpio_sync_in, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ad7768_set_freq(struct ad7768_state *st,
|
|
unsigned int freq)
|
|
{
|
|
unsigned int diff_new, diff_old, pwr_mode, i, idx;
|
|
int res, ret;
|
|
|
|
diff_old = U32_MAX;
|
|
idx = 0;
|
|
|
|
res = DIV_ROUND_CLOSEST(st->mclk_freq, freq);
|
|
|
|
/* Find the closest match for the desired sampling frequency */
|
|
for (i = 0; i < ARRAY_SIZE(ad7768_clk_config); i++) {
|
|
diff_new = abs(res - ad7768_clk_config[i].clk_div);
|
|
if (diff_new < diff_old) {
|
|
diff_old = diff_new;
|
|
idx = i;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Set both the mclk_div and pwrmode with a single write to the
|
|
* POWER_CLOCK register
|
|
*/
|
|
pwr_mode = AD7768_PWR_MCLK_DIV(ad7768_clk_config[idx].mclk_div) |
|
|
AD7768_PWR_PWRMODE(ad7768_clk_config[idx].pwrmode);
|
|
ret = ad7768_spi_reg_write(st, AD7768_REG_POWER_CLOCK, pwr_mode);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = ad7768_set_dig_fil(st, ad7768_clk_config[idx].dec_rate);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
st->samp_freq = DIV_ROUND_CLOSEST(st->mclk_freq,
|
|
ad7768_clk_config[idx].clk_div);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static ssize_t ad7768_sampling_freq_avail(struct device *dev,
|
|
struct device_attribute *attr,
|
|
char *buf)
|
|
{
|
|
struct iio_dev *indio_dev = dev_to_iio_dev(dev);
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
unsigned int freq;
|
|
int i, len = 0;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(ad7768_clk_config); i++) {
|
|
freq = DIV_ROUND_CLOSEST(st->mclk_freq,
|
|
ad7768_clk_config[i].clk_div);
|
|
len += scnprintf(buf + len, PAGE_SIZE - len, "%d ", freq);
|
|
}
|
|
|
|
buf[len - 1] = '\n';
|
|
|
|
return len;
|
|
}
|
|
|
|
static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(ad7768_sampling_freq_avail);
|
|
|
|
static int ad7768_read_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *chan,
|
|
int *val, int *val2, long info)
|
|
{
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
int scale_uv, ret;
|
|
|
|
switch (info) {
|
|
case IIO_CHAN_INFO_RAW:
|
|
ret = iio_device_claim_direct_mode(indio_dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = ad7768_scan_direct(indio_dev);
|
|
if (ret >= 0)
|
|
*val = ret;
|
|
|
|
iio_device_release_direct_mode(indio_dev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return IIO_VAL_INT;
|
|
|
|
case IIO_CHAN_INFO_SCALE:
|
|
scale_uv = regulator_get_voltage(st->vref);
|
|
if (scale_uv < 0)
|
|
return scale_uv;
|
|
|
|
*val = (scale_uv * 2) / 1000;
|
|
*val2 = chan->scan_type.realbits;
|
|
|
|
return IIO_VAL_FRACTIONAL_LOG2;
|
|
|
|
case IIO_CHAN_INFO_SAMP_FREQ:
|
|
*val = st->samp_freq;
|
|
|
|
return IIO_VAL_INT;
|
|
}
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static int ad7768_write_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *chan,
|
|
int val, int val2, long info)
|
|
{
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
|
|
switch (info) {
|
|
case IIO_CHAN_INFO_SAMP_FREQ:
|
|
return ad7768_set_freq(st, val);
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
static struct attribute *ad7768_attributes[] = {
|
|
&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
|
|
NULL
|
|
};
|
|
|
|
static const struct attribute_group ad7768_group = {
|
|
.attrs = ad7768_attributes,
|
|
};
|
|
|
|
static const struct iio_info ad7768_info = {
|
|
.attrs = &ad7768_group,
|
|
.read_raw = &ad7768_read_raw,
|
|
.write_raw = &ad7768_write_raw,
|
|
.debugfs_reg_access = &ad7768_reg_access,
|
|
};
|
|
|
|
static int ad7768_setup(struct ad7768_state *st)
|
|
{
|
|
int ret;
|
|
|
|
/*
|
|
* Two writes to the SPI_RESET[1:0] bits are required to initiate
|
|
* a software reset. The bits must first be set to 11, and then
|
|
* to 10. When the sequence is detected, the reset occurs.
|
|
* See the datasheet, page 70.
|
|
*/
|
|
ret = ad7768_spi_reg_write(st, AD7768_REG_SYNC_RESET, 0x3);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = ad7768_spi_reg_write(st, AD7768_REG_SYNC_RESET, 0x2);
|
|
if (ret)
|
|
return ret;
|
|
|
|
st->gpio_sync_in = devm_gpiod_get(&st->spi->dev, "adi,sync-in",
|
|
GPIOD_OUT_LOW);
|
|
if (IS_ERR(st->gpio_sync_in))
|
|
return PTR_ERR(st->gpio_sync_in);
|
|
|
|
/* Set the default sampling frequency to 32000 kSPS */
|
|
return ad7768_set_freq(st, 32000);
|
|
}
|
|
|
|
static irqreturn_t ad7768_trigger_handler(int irq, void *p)
|
|
{
|
|
struct iio_poll_func *pf = p;
|
|
struct iio_dev *indio_dev = pf->indio_dev;
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
int ret;
|
|
|
|
mutex_lock(&st->lock);
|
|
|
|
ret = spi_read(st->spi, &st->data.d32, 3);
|
|
if (ret < 0)
|
|
goto err_unlock;
|
|
|
|
iio_push_to_buffers_with_timestamp(indio_dev, &st->data.d32,
|
|
iio_get_time_ns(indio_dev));
|
|
|
|
iio_trigger_notify_done(indio_dev->trig);
|
|
err_unlock:
|
|
mutex_unlock(&st->lock);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t ad7768_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct iio_dev *indio_dev = dev_id;
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
|
|
if (iio_buffer_enabled(indio_dev))
|
|
iio_trigger_poll(st->trig);
|
|
else
|
|
complete(&st->completion);
|
|
|
|
return IRQ_HANDLED;
|
|
};
|
|
|
|
static int ad7768_buffer_postenable(struct iio_dev *indio_dev)
|
|
{
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
|
|
/*
|
|
* Write a 1 to the LSB of the INTERFACE_FORMAT register to enter
|
|
* continuous read mode. Subsequent data reads do not require an
|
|
* initial 8-bit write to query the ADC_DATA register.
|
|
*/
|
|
return ad7768_spi_reg_write(st, AD7768_REG_INTERFACE_FORMAT, 0x01);
|
|
}
|
|
|
|
static int ad7768_buffer_predisable(struct iio_dev *indio_dev)
|
|
{
|
|
struct ad7768_state *st = iio_priv(indio_dev);
|
|
|
|
/*
|
|
* To exit continuous read mode, perform a single read of the ADC_DATA
|
|
* reg (0x2C), which allows further configuration of the device.
|
|
*/
|
|
return ad7768_spi_reg_read(st, AD7768_REG_ADC_DATA, 3);
|
|
}
|
|
|
|
static const struct iio_buffer_setup_ops ad7768_buffer_ops = {
|
|
.postenable = &ad7768_buffer_postenable,
|
|
.predisable = &ad7768_buffer_predisable,
|
|
};
|
|
|
|
static const struct iio_trigger_ops ad7768_trigger_ops = {
|
|
.validate_device = iio_trigger_validate_own_device,
|
|
};
|
|
|
|
static void ad7768_regulator_disable(void *data)
|
|
{
|
|
struct ad7768_state *st = data;
|
|
|
|
regulator_disable(st->vref);
|
|
}
|
|
|
|
static void ad7768_clk_disable(void *data)
|
|
{
|
|
struct ad7768_state *st = data;
|
|
|
|
clk_disable_unprepare(st->mclk);
|
|
}
|
|
|
|
static int ad7768_probe(struct spi_device *spi)
|
|
{
|
|
struct ad7768_state *st;
|
|
struct iio_dev *indio_dev;
|
|
int ret;
|
|
|
|
indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
|
|
if (!indio_dev)
|
|
return -ENOMEM;
|
|
|
|
st = iio_priv(indio_dev);
|
|
st->spi = spi;
|
|
|
|
st->vref = devm_regulator_get(&spi->dev, "vref");
|
|
if (IS_ERR(st->vref))
|
|
return PTR_ERR(st->vref);
|
|
|
|
ret = regulator_enable(st->vref);
|
|
if (ret) {
|
|
dev_err(&spi->dev, "Failed to enable specified vref supply\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = devm_add_action_or_reset(&spi->dev, ad7768_regulator_disable, st);
|
|
if (ret)
|
|
return ret;
|
|
|
|
st->mclk = devm_clk_get(&spi->dev, "mclk");
|
|
if (IS_ERR(st->mclk))
|
|
return PTR_ERR(st->mclk);
|
|
|
|
ret = clk_prepare_enable(st->mclk);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = devm_add_action_or_reset(&spi->dev, ad7768_clk_disable, st);
|
|
if (ret)
|
|
return ret;
|
|
|
|
st->mclk_freq = clk_get_rate(st->mclk);
|
|
|
|
spi_set_drvdata(spi, indio_dev);
|
|
mutex_init(&st->lock);
|
|
|
|
indio_dev->channels = ad7768_channels;
|
|
indio_dev->num_channels = ARRAY_SIZE(ad7768_channels);
|
|
indio_dev->name = spi_get_device_id(spi)->name;
|
|
indio_dev->info = &ad7768_info;
|
|
indio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_TRIGGERED;
|
|
|
|
ret = ad7768_setup(st);
|
|
if (ret < 0) {
|
|
dev_err(&spi->dev, "AD7768 setup failed\n");
|
|
return ret;
|
|
}
|
|
|
|
st->trig = devm_iio_trigger_alloc(&spi->dev, "%s-dev%d",
|
|
indio_dev->name, indio_dev->id);
|
|
if (!st->trig)
|
|
return -ENOMEM;
|
|
|
|
st->trig->ops = &ad7768_trigger_ops;
|
|
st->trig->dev.parent = &spi->dev;
|
|
iio_trigger_set_drvdata(st->trig, indio_dev);
|
|
ret = devm_iio_trigger_register(&spi->dev, st->trig);
|
|
if (ret)
|
|
return ret;
|
|
|
|
indio_dev->trig = iio_trigger_get(st->trig);
|
|
|
|
init_completion(&st->completion);
|
|
|
|
ret = devm_request_irq(&spi->dev, spi->irq,
|
|
&ad7768_interrupt,
|
|
IRQF_TRIGGER_RISING | IRQF_ONESHOT,
|
|
indio_dev->name, indio_dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = devm_iio_triggered_buffer_setup(&spi->dev, indio_dev,
|
|
&iio_pollfunc_store_time,
|
|
&ad7768_trigger_handler,
|
|
&ad7768_buffer_ops);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return devm_iio_device_register(&spi->dev, indio_dev);
|
|
}
|
|
|
|
static const struct spi_device_id ad7768_id_table[] = {
|
|
{ "ad7768-1", 0 },
|
|
{}
|
|
};
|
|
MODULE_DEVICE_TABLE(spi, ad7768_id_table);
|
|
|
|
static const struct of_device_id ad7768_of_match[] = {
|
|
{ .compatible = "adi,ad7768-1" },
|
|
{ },
|
|
};
|
|
MODULE_DEVICE_TABLE(of, ad7768_of_match);
|
|
|
|
static struct spi_driver ad7768_driver = {
|
|
.driver = {
|
|
.name = "ad7768-1",
|
|
.of_match_table = ad7768_of_match,
|
|
},
|
|
.probe = ad7768_probe,
|
|
.id_table = ad7768_id_table,
|
|
};
|
|
module_spi_driver(ad7768_driver);
|
|
|
|
MODULE_AUTHOR("Stefan Popa <stefan.popa@analog.com>");
|
|
MODULE_DESCRIPTION("Analog Devices AD7768-1 ADC driver");
|
|
MODULE_LICENSE("GPL v2");
|