f02e0468c4
* R-Car Gen3 boards and SoCs
- Make phy-mode of EtherAVB a board-specific property.
The SoC DTs file now uses "rgmii" and boards override this with
"rgmii-txid" as appropriate. Previously "rgmii-txid" was used
in SoC DTs but this did not describe that more sophiticated
functionality is a board rather than SoC property.
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* R-Car D3 (r8a77995)
- Add I2C nodes and then describing the PCA9654 I/O expander connected to
the I2C0 bus.
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable PFC support for configuring SCIF0 pins
This uses PFC support added to the V3M DT
- Describe EtherAVB PHY IRQ
This uses support for GPIO added to the V3M DT
- Enable I2C0 support
Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
we're only describing the former chip now)."
* R-Car V3M (r8a77970) SoCs
- Add PFC support
- Describe GPIO devices
- Describe I2C devices
- Srt subnodes of root node alphabetically to eas future maintence overhead
* Draak board with R-Car D3 (r8a77995) SoC
- Enable SDHI2
Wolfram Sang says "The single SDHI controller is connected to eMMC."
- Enable DU
Kieran Bingham says "Enable the DU, providing only the VGA output for
now."
* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
- Move nodes which have no reg property out of bus
By deffinition the bus only has hardware with an address on the bus
- Remove non-existing STBE region from EtherAVB
Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
* R-Car D3 (r8a77995) SoC
- Add FCPV, VSP and DU support
Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
One VSPBS can be used as a dual-input image blender, while two VSPD
instances can be utilised as part of a display (DU) pipeline.
Add support for these, along with their required FCPV nodes."
* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
- Add GPIO extender
This is a basis for follow-up work to configure the GPIOs of the extender
* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
- Initial upstream support
* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Add OPPs table for cpu devices
This, along with recently upstreamed Z and Z2 clock support allows
use of CPUFreq with both A57 and A53 CPUs.
- Add thermal cooling management
Allows the use of CPUFreq as a cooling device on A57 CPUs
- Correct register size of thermal node
Niklas Söderlund says "To be able to read fused calibration values from
hardware the size of the register resource of TSC1 needs to be
incremented to cover one more register which holds the information if
the calibration values have been fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry"
- Fix register mappings on VSPs
Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
register space is mapped correctly to support this."
* R-Car H3 (r8a7795) SoC
- Move SCIF node into alphabetical order to ease future maintenance overhead
- Add IPMMU-PV1 device node
This resolves an oversight when IPMMU nodes were added to the H3 DT.
All IPMMU devices should now be described in DT.
- Add missing SYS-DMAC2 dmas
Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
can make use of DMA are wired to either SYS-DMAC0 only, or to both
SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has
been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
2016)."
-----BEGIN PGP SIGNATURE-----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=wu1f
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM64 Based SoC DT Updates for v4.17" from Simon Horman:
* R-Car Gen3 boards and SoCs
- Make phy-mode of EtherAVB a board-specific property.
The SoC DTs file now uses "rgmii" and boards override this with
"rgmii-txid" as appropriate. Previously "rgmii-txid" was used
in SoC DTs but this did not describe that more sophiticated
functionality is a board rather than SoC property.
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* R-Car D3 (r8a77995)
- Add I2C nodes and then describing the PCA9654 I/O expander connected to
the I2C0 bus.
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable PFC support for configuring SCIF0 pins
This uses PFC support added to the V3M DT
- Describe EtherAVB PHY IRQ
This uses support for GPIO added to the V3M DT
- Enable I2C0 support
Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
we're only describing the former chip now)."
* R-Car V3M (r8a77970) SoCs
- Add PFC support
- Describe GPIO devices
- Describe I2C devices
- Srt subnodes of root node alphabetically to eas future maintence overhead
* Draak board with R-Car D3 (r8a77995) SoC
- Enable SDHI2
Wolfram Sang says "The single SDHI controller is connected to eMMC."
- Enable DU
Kieran Bingham says "Enable the DU, providing only the VGA output for
now."
* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
- Move nodes which have no reg property out of bus
By deffinition the bus only has hardware with an address on the bus
- Remove non-existing STBE region from EtherAVB
Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
* R-Car D3 (r8a77995) SoC
- Add FCPV, VSP and DU support
Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
One VSPBS can be used as a dual-input image blender, while two VSPD
instances can be utilised as part of a display (DU) pipeline.
Add support for these, along with their required FCPV nodes."
* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
- Add GPIO extender
This is a basis for follow-up work to configure the GPIOs of the extender
* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
- Initial upstream support
* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Add OPPs table for cpu devices
This, along with recently upstreamed Z and Z2 clock support allows
use of CPUFreq with both A57 and A53 CPUs.
- Add thermal cooling management
Allows the use of CPUFreq as a cooling device on A57 CPUs
- Correct register size of thermal node
Niklas Söderlund says "To be able to read fused calibration values from
hardware the size of the register resource of TSC1 needs to be
incremented to cover one more register which holds the information if
the calibration values have been fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry"
- Fix register mappings on VSPs
Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
register space is mapped correctly to support this."
* R-Car H3 (r8a7795) SoC
- Move SCIF node into alphabetical order to ease future maintenance overhead
- Add IPMMU-PV1 device node
This resolves an oversight when IPMMU nodes were added to the H3 DT.
All IPMMU devices should now be described in DT.
- Add missing SYS-DMAC2 dmas
Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
can make use of DMA are wired to either SYS-DMAC0 only, or to both
SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has
been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
2016)."
* tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
arm64: dts: renesas: v3msk: add SCIF0 pins
arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas
arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node
arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically
arm64: dts: renesas: eagle: add I2C0 support
arm64: dts: renesas: r8a77970: add I2C support
arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header
arm64: dts: renesas: r8a77965: Add EtherAVB device node
arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: v3msk: Override EtherAVB phy-mode
arm64: dts: renesas: eagle: Override EtherAVB phy-mode
arm64: dts: renesas: draak: Override EtherAVB phy-mode
arm64: dts: renesas: ulcb: Override EtherAVB phy-mode
arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode
arm64: dts: renesas: r8a77965: Add INTC-EX device node
arm64: dts: renesas: r8a77965: Add IIC-DVFS device node
arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N
...
|
||
|---|---|---|
| Documentation | ||
| LICENSES | ||
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| drivers | ||
| firmware | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
README
Linux kernel ============ This file was moved to Documentation/admin-guide/README.rst Please notice that there are several guides for kernel developers and users. These guides can be rendered in a number of formats, like HTML and PDF. In order to build the documentation, use ``make htmldocs`` or ``make pdfdocs``. There are various text files in the Documentation/ subdirectory, several of them using the Restructured Text markup notation. See Documentation/00-INDEX for a list of what is contained in each file. Please read the Documentation/process/changes.rst file, as it contains the requirements for building and running the kernel, and information about the problems which may result by upgrading your kernel.