176 lines
6.6 KiB
Plaintext
176 lines
6.6 KiB
Plaintext
Transactional Memory support
|
|
============================
|
|
|
|
POWER kernel support for this feature is currently limited to supporting
|
|
its use by user programs. It is not currently used by the kernel itself.
|
|
|
|
This file aims to sum up how it is supported by Linux and what behaviour you
|
|
can expect from your user programs.
|
|
|
|
|
|
Basic overview
|
|
==============
|
|
|
|
Hardware Transactional Memory is supported on POWER8 processors, and is a
|
|
feature that enables a different form of atomic memory access. Several new
|
|
instructions are presented to delimit transactions; transactions are
|
|
guaranteed to either complete atomically or roll back and undo any partial
|
|
changes.
|
|
|
|
A simple transaction looks like this:
|
|
|
|
begin_move_money:
|
|
tbegin
|
|
beq abort_handler
|
|
|
|
ld r4, SAVINGS_ACCT(r3)
|
|
ld r5, CURRENT_ACCT(r3)
|
|
subi r5, r5, 1
|
|
addi r4, r4, 1
|
|
std r4, SAVINGS_ACCT(r3)
|
|
std r5, CURRENT_ACCT(r3)
|
|
|
|
tend
|
|
|
|
b continue
|
|
|
|
abort_handler:
|
|
... test for odd failures ...
|
|
|
|
/* Retry the transaction if it failed because it conflicted with
|
|
* someone else: */
|
|
b begin_move_money
|
|
|
|
|
|
The 'tbegin' instruction denotes the start point, and 'tend' the end point.
|
|
Between these points the processor is in 'Transactional' state; any memory
|
|
references will complete in one go if there are no conflicts with other
|
|
transactional or non-transactional accesses within the system. In this
|
|
example, the transaction completes as though it were normal straight-line code
|
|
IF no other processor has touched SAVINGS_ACCT(r3) or CURRENT_ACCT(r3); an
|
|
atomic move of money from the current account to the savings account has been
|
|
performed. Even though the normal ld/std instructions are used (note no
|
|
lwarx/stwcx), either *both* SAVINGS_ACCT(r3) and CURRENT_ACCT(r3) will be
|
|
updated, or neither will be updated.
|
|
|
|
If, in the meantime, there is a conflict with the locations accessed by the
|
|
transaction, the transaction will be aborted by the CPU. Register and memory
|
|
state will roll back to that at the 'tbegin', and control will continue from
|
|
'tbegin+4'. The branch to abort_handler will be taken this second time; the
|
|
abort handler can check the cause of the failure, and retry.
|
|
|
|
Checkpointed registers include all GPRs, FPRs, VRs/VSRs, LR, CCR/CR, CTR, FPCSR
|
|
and a few other status/flag regs; see the ISA for details.
|
|
|
|
Causes of transaction aborts
|
|
============================
|
|
|
|
- Conflicts with cache lines used by other processors
|
|
- Signals
|
|
- Context switches
|
|
- See the ISA for full documentation of everything that will abort transactions.
|
|
|
|
|
|
Syscalls
|
|
========
|
|
|
|
Performing syscalls from within transaction is not recommended, and can lead
|
|
to unpredictable results.
|
|
|
|
Syscalls do not by design abort transactions, but beware: The kernel code will
|
|
not be running in transactional state. The effect of syscalls will always
|
|
remain visible, but depending on the call they may abort your transaction as a
|
|
side-effect, read soon-to-be-aborted transactional data that should not remain
|
|
invisible, etc. If you constantly retry a transaction that constantly aborts
|
|
itself by calling a syscall, you'll have a livelock & make no progress.
|
|
|
|
Simple syscalls (e.g. sigprocmask()) "could" be OK. Even things like write()
|
|
from, say, printf() should be OK as long as the kernel does not access any
|
|
memory that was accessed transactionally.
|
|
|
|
Consider any syscalls that happen to work as debug-only -- not recommended for
|
|
production use. Best to queue them up till after the transaction is over.
|
|
|
|
|
|
Signals
|
|
=======
|
|
|
|
Delivery of signals (both sync and async) during transactions provides a second
|
|
thread state (ucontext/mcontext) to represent the second transactional register
|
|
state. Signal delivery 'treclaim's to capture both register states, so signals
|
|
abort transactions. The usual ucontext_t passed to the signal handler
|
|
represents the checkpointed/original register state; the signal appears to have
|
|
arisen at 'tbegin+4'.
|
|
|
|
If the sighandler ucontext has uc_link set, a second ucontext has been
|
|
delivered. For future compatibility the MSR.TS field should be checked to
|
|
determine the transactional state -- if so, the second ucontext in uc->uc_link
|
|
represents the active transactional registers at the point of the signal.
|
|
|
|
For 64-bit processes, uc->uc_mcontext.regs->msr is a full 64-bit MSR and its TS
|
|
field shows the transactional mode.
|
|
|
|
For 32-bit processes, the mcontext's MSR register is only 32 bits; the top 32
|
|
bits are stored in the MSR of the second ucontext, i.e. in
|
|
uc->uc_link->uc_mcontext.regs->msr. The top word contains the transactional
|
|
state TS.
|
|
|
|
However, basic signal handlers don't need to be aware of transactions
|
|
and simply returning from the handler will deal with things correctly:
|
|
|
|
Transaction-aware signal handlers can read the transactional register state
|
|
from the second ucontext. This will be necessary for crash handlers to
|
|
determine, for example, the address of the instruction causing the SIGSEGV.
|
|
|
|
Example signal handler:
|
|
|
|
void crash_handler(int sig, siginfo_t *si, void *uc)
|
|
{
|
|
ucontext_t *ucp = uc;
|
|
ucontext_t *transactional_ucp = ucp->uc_link;
|
|
|
|
if (ucp_link) {
|
|
u64 msr = ucp->uc_mcontext.regs->msr;
|
|
/* May have transactional ucontext! */
|
|
#ifndef __powerpc64__
|
|
msr |= ((u64)transactional_ucp->uc_mcontext.regs->msr) << 32;
|
|
#endif
|
|
if (MSR_TM_ACTIVE(msr)) {
|
|
/* Yes, we crashed during a transaction. Oops. */
|
|
fprintf(stderr, "Transaction to be restarted at 0x%llx, but "
|
|
"crashy instruction was at 0x%llx\n",
|
|
ucp->uc_mcontext.regs->nip,
|
|
transactional_ucp->uc_mcontext.regs->nip);
|
|
}
|
|
}
|
|
|
|
fix_the_problem(ucp->dar);
|
|
}
|
|
|
|
|
|
Failure cause codes used by kernel
|
|
==================================
|
|
|
|
These are defined in <asm/reg.h>, and distinguish different reasons why the
|
|
kernel aborted a transaction:
|
|
|
|
TM_CAUSE_RESCHED Thread was rescheduled.
|
|
TM_CAUSE_FAC_UNAV FP/VEC/VSX unavailable trap.
|
|
TM_CAUSE_SYSCALL Currently unused; future syscalls that must abort
|
|
transactions for consistency will use this.
|
|
TM_CAUSE_SIGNAL Signal delivered.
|
|
TM_CAUSE_MISC Currently unused.
|
|
|
|
These can be checked by the user program's abort handler as TEXASR[0:7].
|
|
|
|
|
|
GDB
|
|
===
|
|
|
|
GDB and ptrace are not currently TM-aware. If one stops during a transaction,
|
|
it looks like the transaction has just started (the checkpointed state is
|
|
presented). The transaction cannot then be continued and will take the failure
|
|
handler route. Furthermore, the transactional 2nd register state will be
|
|
inaccessible. GDB can currently be used on programs using TM, but not sensibly
|
|
in parts within transactions.
|