2367 lines
54 KiB
C
2367 lines
54 KiB
C
/*
|
|
* Copyright (C) 2005-2006 Atmel Corporation
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/dw_dmac.h>
|
|
#include <linux/fb.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/usb/atmel_usba_udc.h>
|
|
|
|
#include <mach/atmel-mci.h>
|
|
#include <linux/atmel-mci.h>
|
|
|
|
#include <asm/io.h>
|
|
#include <asm/irq.h>
|
|
|
|
#include <mach/at32ap700x.h>
|
|
#include <mach/board.h>
|
|
#include <mach/hmatrix.h>
|
|
#include <mach/portmux.h>
|
|
#include <mach/sram.h>
|
|
|
|
#include <sound/atmel-abdac.h>
|
|
#include <sound/atmel-ac97c.h>
|
|
|
|
#include <video/atmel_lcdc.h>
|
|
|
|
#include "clock.h"
|
|
#include "pio.h"
|
|
#include "pm.h"
|
|
|
|
|
|
#define PBMEM(base) \
|
|
{ \
|
|
.start = base, \
|
|
.end = base + 0x3ff, \
|
|
.flags = IORESOURCE_MEM, \
|
|
}
|
|
#define IRQ(num) \
|
|
{ \
|
|
.start = num, \
|
|
.end = num, \
|
|
.flags = IORESOURCE_IRQ, \
|
|
}
|
|
#define NAMED_IRQ(num, _name) \
|
|
{ \
|
|
.start = num, \
|
|
.end = num, \
|
|
.name = _name, \
|
|
.flags = IORESOURCE_IRQ, \
|
|
}
|
|
|
|
/* REVISIT these assume *every* device supports DMA, but several
|
|
* don't ... tc, smc, pio, rtc, watchdog, pwm, ps2, and more.
|
|
*/
|
|
#define DEFINE_DEV(_name, _id) \
|
|
static u64 _name##_id##_dma_mask = DMA_BIT_MASK(32); \
|
|
static struct platform_device _name##_id##_device = { \
|
|
.name = #_name, \
|
|
.id = _id, \
|
|
.dev = { \
|
|
.dma_mask = &_name##_id##_dma_mask, \
|
|
.coherent_dma_mask = DMA_BIT_MASK(32), \
|
|
}, \
|
|
.resource = _name##_id##_resource, \
|
|
.num_resources = ARRAY_SIZE(_name##_id##_resource), \
|
|
}
|
|
#define DEFINE_DEV_DATA(_name, _id) \
|
|
static u64 _name##_id##_dma_mask = DMA_BIT_MASK(32); \
|
|
static struct platform_device _name##_id##_device = { \
|
|
.name = #_name, \
|
|
.id = _id, \
|
|
.dev = { \
|
|
.dma_mask = &_name##_id##_dma_mask, \
|
|
.platform_data = &_name##_id##_data, \
|
|
.coherent_dma_mask = DMA_BIT_MASK(32), \
|
|
}, \
|
|
.resource = _name##_id##_resource, \
|
|
.num_resources = ARRAY_SIZE(_name##_id##_resource), \
|
|
}
|
|
|
|
#define select_peripheral(port, pin_mask, periph, flags) \
|
|
at32_select_periph(GPIO_##port##_BASE, pin_mask, \
|
|
GPIO_##periph, flags)
|
|
|
|
#define DEV_CLK(_name, devname, bus, _index) \
|
|
static struct clk devname##_##_name = { \
|
|
.name = #_name, \
|
|
.dev = &devname##_device.dev, \
|
|
.parent = &bus##_clk, \
|
|
.mode = bus##_clk_mode, \
|
|
.get_rate = bus##_clk_get_rate, \
|
|
.index = _index, \
|
|
}
|
|
|
|
static DEFINE_SPINLOCK(pm_lock);
|
|
|
|
static struct clk osc0;
|
|
static struct clk osc1;
|
|
|
|
static unsigned long osc_get_rate(struct clk *clk)
|
|
{
|
|
return at32_board_osc_rates[clk->index];
|
|
}
|
|
|
|
static unsigned long pll_get_rate(struct clk *clk, unsigned long control)
|
|
{
|
|
unsigned long div, mul, rate;
|
|
|
|
div = PM_BFEXT(PLLDIV, control) + 1;
|
|
mul = PM_BFEXT(PLLMUL, control) + 1;
|
|
|
|
rate = clk->parent->get_rate(clk->parent);
|
|
rate = (rate + div / 2) / div;
|
|
rate *= mul;
|
|
|
|
return rate;
|
|
}
|
|
|
|
static long pll_set_rate(struct clk *clk, unsigned long rate,
|
|
u32 *pll_ctrl)
|
|
{
|
|
unsigned long mul;
|
|
unsigned long mul_best_fit = 0;
|
|
unsigned long div;
|
|
unsigned long div_min;
|
|
unsigned long div_max;
|
|
unsigned long div_best_fit = 0;
|
|
unsigned long base;
|
|
unsigned long pll_in;
|
|
unsigned long actual = 0;
|
|
unsigned long rate_error;
|
|
unsigned long rate_error_prev = ~0UL;
|
|
u32 ctrl;
|
|
|
|
/* Rate must be between 80 MHz and 200 Mhz. */
|
|
if (rate < 80000000UL || rate > 200000000UL)
|
|
return -EINVAL;
|
|
|
|
ctrl = PM_BF(PLLOPT, 4);
|
|
base = clk->parent->get_rate(clk->parent);
|
|
|
|
/* PLL input frequency must be between 6 MHz and 32 MHz. */
|
|
div_min = DIV_ROUND_UP(base, 32000000UL);
|
|
div_max = base / 6000000UL;
|
|
|
|
if (div_max < div_min)
|
|
return -EINVAL;
|
|
|
|
for (div = div_min; div <= div_max; div++) {
|
|
pll_in = (base + div / 2) / div;
|
|
mul = (rate + pll_in / 2) / pll_in;
|
|
|
|
if (mul == 0)
|
|
continue;
|
|
|
|
actual = pll_in * mul;
|
|
rate_error = abs(actual - rate);
|
|
|
|
if (rate_error < rate_error_prev) {
|
|
mul_best_fit = mul;
|
|
div_best_fit = div;
|
|
rate_error_prev = rate_error;
|
|
}
|
|
|
|
if (rate_error == 0)
|
|
break;
|
|
}
|
|
|
|
if (div_best_fit == 0)
|
|
return -EINVAL;
|
|
|
|
ctrl |= PM_BF(PLLMUL, mul_best_fit - 1);
|
|
ctrl |= PM_BF(PLLDIV, div_best_fit - 1);
|
|
ctrl |= PM_BF(PLLCOUNT, 16);
|
|
|
|
if (clk->parent == &osc1)
|
|
ctrl |= PM_BIT(PLLOSC);
|
|
|
|
*pll_ctrl = ctrl;
|
|
|
|
return actual;
|
|
}
|
|
|
|
static unsigned long pll0_get_rate(struct clk *clk)
|
|
{
|
|
u32 control;
|
|
|
|
control = pm_readl(PLL0);
|
|
|
|
return pll_get_rate(clk, control);
|
|
}
|
|
|
|
static void pll1_mode(struct clk *clk, int enabled)
|
|
{
|
|
unsigned long timeout;
|
|
u32 status;
|
|
u32 ctrl;
|
|
|
|
ctrl = pm_readl(PLL1);
|
|
|
|
if (enabled) {
|
|
if (!PM_BFEXT(PLLMUL, ctrl) && !PM_BFEXT(PLLDIV, ctrl)) {
|
|
pr_debug("clk %s: failed to enable, rate not set\n",
|
|
clk->name);
|
|
return;
|
|
}
|
|
|
|
ctrl |= PM_BIT(PLLEN);
|
|
pm_writel(PLL1, ctrl);
|
|
|
|
/* Wait for PLL lock. */
|
|
for (timeout = 10000; timeout; timeout--) {
|
|
status = pm_readl(ISR);
|
|
if (status & PM_BIT(LOCK1))
|
|
break;
|
|
udelay(10);
|
|
}
|
|
|
|
if (!(status & PM_BIT(LOCK1)))
|
|
printk(KERN_ERR "clk %s: timeout waiting for lock\n",
|
|
clk->name);
|
|
} else {
|
|
ctrl &= ~PM_BIT(PLLEN);
|
|
pm_writel(PLL1, ctrl);
|
|
}
|
|
}
|
|
|
|
static unsigned long pll1_get_rate(struct clk *clk)
|
|
{
|
|
u32 control;
|
|
|
|
control = pm_readl(PLL1);
|
|
|
|
return pll_get_rate(clk, control);
|
|
}
|
|
|
|
static long pll1_set_rate(struct clk *clk, unsigned long rate, int apply)
|
|
{
|
|
u32 ctrl = 0;
|
|
unsigned long actual_rate;
|
|
|
|
actual_rate = pll_set_rate(clk, rate, &ctrl);
|
|
|
|
if (apply) {
|
|
if (actual_rate != rate)
|
|
return -EINVAL;
|
|
if (clk->users > 0)
|
|
return -EBUSY;
|
|
pr_debug(KERN_INFO "clk %s: new rate %lu (actual rate %lu)\n",
|
|
clk->name, rate, actual_rate);
|
|
pm_writel(PLL1, ctrl);
|
|
}
|
|
|
|
return actual_rate;
|
|
}
|
|
|
|
static int pll1_set_parent(struct clk *clk, struct clk *parent)
|
|
{
|
|
u32 ctrl;
|
|
|
|
if (clk->users > 0)
|
|
return -EBUSY;
|
|
|
|
ctrl = pm_readl(PLL1);
|
|
WARN_ON(ctrl & PM_BIT(PLLEN));
|
|
|
|
if (parent == &osc0)
|
|
ctrl &= ~PM_BIT(PLLOSC);
|
|
else if (parent == &osc1)
|
|
ctrl |= PM_BIT(PLLOSC);
|
|
else
|
|
return -EINVAL;
|
|
|
|
pm_writel(PLL1, ctrl);
|
|
clk->parent = parent;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* The AT32AP7000 has five primary clock sources: One 32kHz
|
|
* oscillator, two crystal oscillators and two PLLs.
|
|
*/
|
|
static struct clk osc32k = {
|
|
.name = "osc32k",
|
|
.get_rate = osc_get_rate,
|
|
.users = 1,
|
|
.index = 0,
|
|
};
|
|
static struct clk osc0 = {
|
|
.name = "osc0",
|
|
.get_rate = osc_get_rate,
|
|
.users = 1,
|
|
.index = 1,
|
|
};
|
|
static struct clk osc1 = {
|
|
.name = "osc1",
|
|
.get_rate = osc_get_rate,
|
|
.index = 2,
|
|
};
|
|
static struct clk pll0 = {
|
|
.name = "pll0",
|
|
.get_rate = pll0_get_rate,
|
|
.parent = &osc0,
|
|
};
|
|
static struct clk pll1 = {
|
|
.name = "pll1",
|
|
.mode = pll1_mode,
|
|
.get_rate = pll1_get_rate,
|
|
.set_rate = pll1_set_rate,
|
|
.set_parent = pll1_set_parent,
|
|
.parent = &osc0,
|
|
};
|
|
|
|
/*
|
|
* The main clock can be either osc0 or pll0. The boot loader may
|
|
* have chosen one for us, so we don't really know which one until we
|
|
* have a look at the SM.
|
|
*/
|
|
static struct clk *main_clock;
|
|
|
|
/*
|
|
* Synchronous clocks are generated from the main clock. The clocks
|
|
* must satisfy the constraint
|
|
* fCPU >= fHSB >= fPB
|
|
* i.e. each clock must not be faster than its parent.
|
|
*/
|
|
static unsigned long bus_clk_get_rate(struct clk *clk, unsigned int shift)
|
|
{
|
|
return main_clock->get_rate(main_clock) >> shift;
|
|
};
|
|
|
|
static void cpu_clk_mode(struct clk *clk, int enabled)
|
|
{
|
|
unsigned long flags;
|
|
u32 mask;
|
|
|
|
spin_lock_irqsave(&pm_lock, flags);
|
|
mask = pm_readl(CPU_MASK);
|
|
if (enabled)
|
|
mask |= 1 << clk->index;
|
|
else
|
|
mask &= ~(1 << clk->index);
|
|
pm_writel(CPU_MASK, mask);
|
|
spin_unlock_irqrestore(&pm_lock, flags);
|
|
}
|
|
|
|
static unsigned long cpu_clk_get_rate(struct clk *clk)
|
|
{
|
|
unsigned long cksel, shift = 0;
|
|
|
|
cksel = pm_readl(CKSEL);
|
|
if (cksel & PM_BIT(CPUDIV))
|
|
shift = PM_BFEXT(CPUSEL, cksel) + 1;
|
|
|
|
return bus_clk_get_rate(clk, shift);
|
|
}
|
|
|
|
static long cpu_clk_set_rate(struct clk *clk, unsigned long rate, int apply)
|
|
{
|
|
u32 control;
|
|
unsigned long parent_rate, child_div, actual_rate, div;
|
|
|
|
parent_rate = clk->parent->get_rate(clk->parent);
|
|
control = pm_readl(CKSEL);
|
|
|
|
if (control & PM_BIT(HSBDIV))
|
|
child_div = 1 << (PM_BFEXT(HSBSEL, control) + 1);
|
|
else
|
|
child_div = 1;
|
|
|
|
if (rate > 3 * (parent_rate / 4) || child_div == 1) {
|
|
actual_rate = parent_rate;
|
|
control &= ~PM_BIT(CPUDIV);
|
|
} else {
|
|
unsigned int cpusel;
|
|
div = (parent_rate + rate / 2) / rate;
|
|
if (div > child_div)
|
|
div = child_div;
|
|
cpusel = (div > 1) ? (fls(div) - 2) : 0;
|
|
control = PM_BIT(CPUDIV) | PM_BFINS(CPUSEL, cpusel, control);
|
|
actual_rate = parent_rate / (1 << (cpusel + 1));
|
|
}
|
|
|
|
pr_debug("clk %s: new rate %lu (actual rate %lu)\n",
|
|
clk->name, rate, actual_rate);
|
|
|
|
if (apply)
|
|
pm_writel(CKSEL, control);
|
|
|
|
return actual_rate;
|
|
}
|
|
|
|
static void hsb_clk_mode(struct clk *clk, int enabled)
|
|
{
|
|
unsigned long flags;
|
|
u32 mask;
|
|
|
|
spin_lock_irqsave(&pm_lock, flags);
|
|
mask = pm_readl(HSB_MASK);
|
|
if (enabled)
|
|
mask |= 1 << clk->index;
|
|
else
|
|
mask &= ~(1 << clk->index);
|
|
pm_writel(HSB_MASK, mask);
|
|
spin_unlock_irqrestore(&pm_lock, flags);
|
|
}
|
|
|
|
static unsigned long hsb_clk_get_rate(struct clk *clk)
|
|
{
|
|
unsigned long cksel, shift = 0;
|
|
|
|
cksel = pm_readl(CKSEL);
|
|
if (cksel & PM_BIT(HSBDIV))
|
|
shift = PM_BFEXT(HSBSEL, cksel) + 1;
|
|
|
|
return bus_clk_get_rate(clk, shift);
|
|
}
|
|
|
|
void pba_clk_mode(struct clk *clk, int enabled)
|
|
{
|
|
unsigned long flags;
|
|
u32 mask;
|
|
|
|
spin_lock_irqsave(&pm_lock, flags);
|
|
mask = pm_readl(PBA_MASK);
|
|
if (enabled)
|
|
mask |= 1 << clk->index;
|
|
else
|
|
mask &= ~(1 << clk->index);
|
|
pm_writel(PBA_MASK, mask);
|
|
spin_unlock_irqrestore(&pm_lock, flags);
|
|
}
|
|
|
|
unsigned long pba_clk_get_rate(struct clk *clk)
|
|
{
|
|
unsigned long cksel, shift = 0;
|
|
|
|
cksel = pm_readl(CKSEL);
|
|
if (cksel & PM_BIT(PBADIV))
|
|
shift = PM_BFEXT(PBASEL, cksel) + 1;
|
|
|
|
return bus_clk_get_rate(clk, shift);
|
|
}
|
|
|
|
static void pbb_clk_mode(struct clk *clk, int enabled)
|
|
{
|
|
unsigned long flags;
|
|
u32 mask;
|
|
|
|
spin_lock_irqsave(&pm_lock, flags);
|
|
mask = pm_readl(PBB_MASK);
|
|
if (enabled)
|
|
mask |= 1 << clk->index;
|
|
else
|
|
mask &= ~(1 << clk->index);
|
|
pm_writel(PBB_MASK, mask);
|
|
spin_unlock_irqrestore(&pm_lock, flags);
|
|
}
|
|
|
|
static unsigned long pbb_clk_get_rate(struct clk *clk)
|
|
{
|
|
unsigned long cksel, shift = 0;
|
|
|
|
cksel = pm_readl(CKSEL);
|
|
if (cksel & PM_BIT(PBBDIV))
|
|
shift = PM_BFEXT(PBBSEL, cksel) + 1;
|
|
|
|
return bus_clk_get_rate(clk, shift);
|
|
}
|
|
|
|
static struct clk cpu_clk = {
|
|
.name = "cpu",
|
|
.get_rate = cpu_clk_get_rate,
|
|
.set_rate = cpu_clk_set_rate,
|
|
.users = 1,
|
|
};
|
|
static struct clk hsb_clk = {
|
|
.name = "hsb",
|
|
.parent = &cpu_clk,
|
|
.get_rate = hsb_clk_get_rate,
|
|
};
|
|
static struct clk pba_clk = {
|
|
.name = "pba",
|
|
.parent = &hsb_clk,
|
|
.mode = hsb_clk_mode,
|
|
.get_rate = pba_clk_get_rate,
|
|
.index = 1,
|
|
};
|
|
static struct clk pbb_clk = {
|
|
.name = "pbb",
|
|
.parent = &hsb_clk,
|
|
.mode = hsb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.users = 1,
|
|
.index = 2,
|
|
};
|
|
|
|
/* --------------------------------------------------------------------
|
|
* Generic Clock operations
|
|
* -------------------------------------------------------------------- */
|
|
|
|
static void genclk_mode(struct clk *clk, int enabled)
|
|
{
|
|
u32 control;
|
|
|
|
control = pm_readl(GCCTRL(clk->index));
|
|
if (enabled)
|
|
control |= PM_BIT(CEN);
|
|
else
|
|
control &= ~PM_BIT(CEN);
|
|
pm_writel(GCCTRL(clk->index), control);
|
|
}
|
|
|
|
static unsigned long genclk_get_rate(struct clk *clk)
|
|
{
|
|
u32 control;
|
|
unsigned long div = 1;
|
|
|
|
control = pm_readl(GCCTRL(clk->index));
|
|
if (control & PM_BIT(DIVEN))
|
|
div = 2 * (PM_BFEXT(DIV, control) + 1);
|
|
|
|
return clk->parent->get_rate(clk->parent) / div;
|
|
}
|
|
|
|
static long genclk_set_rate(struct clk *clk, unsigned long rate, int apply)
|
|
{
|
|
u32 control;
|
|
unsigned long parent_rate, actual_rate, div;
|
|
|
|
parent_rate = clk->parent->get_rate(clk->parent);
|
|
control = pm_readl(GCCTRL(clk->index));
|
|
|
|
if (rate > 3 * parent_rate / 4) {
|
|
actual_rate = parent_rate;
|
|
control &= ~PM_BIT(DIVEN);
|
|
} else {
|
|
div = (parent_rate + rate) / (2 * rate) - 1;
|
|
control = PM_BFINS(DIV, div, control) | PM_BIT(DIVEN);
|
|
actual_rate = parent_rate / (2 * (div + 1));
|
|
}
|
|
|
|
dev_dbg(clk->dev, "clk %s: new rate %lu (actual rate %lu)\n",
|
|
clk->name, rate, actual_rate);
|
|
|
|
if (apply)
|
|
pm_writel(GCCTRL(clk->index), control);
|
|
|
|
return actual_rate;
|
|
}
|
|
|
|
int genclk_set_parent(struct clk *clk, struct clk *parent)
|
|
{
|
|
u32 control;
|
|
|
|
dev_dbg(clk->dev, "clk %s: new parent %s (was %s)\n",
|
|
clk->name, parent->name, clk->parent->name);
|
|
|
|
control = pm_readl(GCCTRL(clk->index));
|
|
|
|
if (parent == &osc1 || parent == &pll1)
|
|
control |= PM_BIT(OSCSEL);
|
|
else if (parent == &osc0 || parent == &pll0)
|
|
control &= ~PM_BIT(OSCSEL);
|
|
else
|
|
return -EINVAL;
|
|
|
|
if (parent == &pll0 || parent == &pll1)
|
|
control |= PM_BIT(PLLSEL);
|
|
else
|
|
control &= ~PM_BIT(PLLSEL);
|
|
|
|
pm_writel(GCCTRL(clk->index), control);
|
|
clk->parent = parent;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void __init genclk_init_parent(struct clk *clk)
|
|
{
|
|
u32 control;
|
|
struct clk *parent;
|
|
|
|
BUG_ON(clk->index > 7);
|
|
|
|
control = pm_readl(GCCTRL(clk->index));
|
|
if (control & PM_BIT(OSCSEL))
|
|
parent = (control & PM_BIT(PLLSEL)) ? &pll1 : &osc1;
|
|
else
|
|
parent = (control & PM_BIT(PLLSEL)) ? &pll0 : &osc0;
|
|
|
|
clk->parent = parent;
|
|
}
|
|
|
|
static struct dw_dma_platform_data dw_dmac0_data = {
|
|
.nr_channels = 3,
|
|
.block_size = 4095U,
|
|
.nr_masters = 2,
|
|
.data_width = { 2, 2, 0, 0 },
|
|
};
|
|
|
|
static struct resource dw_dmac0_resource[] = {
|
|
PBMEM(0xff200000),
|
|
IRQ(2),
|
|
};
|
|
DEFINE_DEV_DATA(dw_dmac, 0);
|
|
DEV_CLK(hclk, dw_dmac0, hsb, 10);
|
|
|
|
/* --------------------------------------------------------------------
|
|
* System peripherals
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource at32_pm0_resource[] = {
|
|
{
|
|
.start = 0xfff00000,
|
|
.end = 0xfff0007f,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(20),
|
|
};
|
|
|
|
static struct resource at32ap700x_rtc0_resource[] = {
|
|
{
|
|
.start = 0xfff00080,
|
|
.end = 0xfff000af,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(21),
|
|
};
|
|
|
|
static struct resource at32_wdt0_resource[] = {
|
|
{
|
|
.start = 0xfff000b0,
|
|
.end = 0xfff000cf,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct resource at32_eic0_resource[] = {
|
|
{
|
|
.start = 0xfff00100,
|
|
.end = 0xfff0013f,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(19),
|
|
};
|
|
|
|
DEFINE_DEV(at32_pm, 0);
|
|
DEFINE_DEV(at32ap700x_rtc, 0);
|
|
DEFINE_DEV(at32_wdt, 0);
|
|
DEFINE_DEV(at32_eic, 0);
|
|
|
|
/*
|
|
* Peripheral clock for PM, RTC, WDT and EIC. PM will ensure that this
|
|
* is always running.
|
|
*/
|
|
static struct clk at32_pm_pclk = {
|
|
.name = "pclk",
|
|
.dev = &at32_pm0_device.dev,
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.users = 1,
|
|
.index = 0,
|
|
};
|
|
|
|
static struct resource intc0_resource[] = {
|
|
PBMEM(0xfff00400),
|
|
};
|
|
struct platform_device at32_intc0_device = {
|
|
.name = "intc",
|
|
.id = 0,
|
|
.resource = intc0_resource,
|
|
.num_resources = ARRAY_SIZE(intc0_resource),
|
|
};
|
|
DEV_CLK(pclk, at32_intc0, pbb, 1);
|
|
|
|
static struct clk ebi_clk = {
|
|
.name = "ebi",
|
|
.parent = &hsb_clk,
|
|
.mode = hsb_clk_mode,
|
|
.get_rate = hsb_clk_get_rate,
|
|
.users = 1,
|
|
};
|
|
static struct clk hramc_clk = {
|
|
.name = "hramc",
|
|
.parent = &hsb_clk,
|
|
.mode = hsb_clk_mode,
|
|
.get_rate = hsb_clk_get_rate,
|
|
.users = 1,
|
|
.index = 3,
|
|
};
|
|
static struct clk sdramc_clk = {
|
|
.name = "sdramc_clk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.users = 1,
|
|
.index = 14,
|
|
};
|
|
|
|
static struct resource smc0_resource[] = {
|
|
PBMEM(0xfff03400),
|
|
};
|
|
DEFINE_DEV(smc, 0);
|
|
DEV_CLK(pclk, smc0, pbb, 13);
|
|
DEV_CLK(mck, smc0, hsb, 0);
|
|
|
|
static struct platform_device pdc_device = {
|
|
.name = "pdc",
|
|
.id = 0,
|
|
};
|
|
DEV_CLK(hclk, pdc, hsb, 4);
|
|
DEV_CLK(pclk, pdc, pba, 16);
|
|
|
|
static struct clk pico_clk = {
|
|
.name = "pico",
|
|
.parent = &cpu_clk,
|
|
.mode = cpu_clk_mode,
|
|
.get_rate = cpu_clk_get_rate,
|
|
.users = 1,
|
|
};
|
|
|
|
/* --------------------------------------------------------------------
|
|
* HMATRIX
|
|
* -------------------------------------------------------------------- */
|
|
|
|
struct clk at32_hmatrix_clk = {
|
|
.name = "hmatrix_clk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.index = 2,
|
|
.users = 1,
|
|
};
|
|
|
|
/*
|
|
* Set bits in the HMATRIX Special Function Register (SFR) used by the
|
|
* External Bus Interface (EBI). This can be used to enable special
|
|
* features like CompactFlash support, NAND Flash support, etc. on
|
|
* certain chipselects.
|
|
*/
|
|
static inline void set_ebi_sfr_bits(u32 mask)
|
|
{
|
|
hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, mask);
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* Timer/Counter (TC)
|
|
* -------------------------------------------------------------------- */
|
|
|
|
static struct resource at32_tcb0_resource[] = {
|
|
PBMEM(0xfff00c00),
|
|
IRQ(22),
|
|
};
|
|
static struct platform_device at32_tcb0_device = {
|
|
.name = "atmel_tcb",
|
|
.id = 0,
|
|
.resource = at32_tcb0_resource,
|
|
.num_resources = ARRAY_SIZE(at32_tcb0_resource),
|
|
};
|
|
DEV_CLK(t0_clk, at32_tcb0, pbb, 3);
|
|
|
|
static struct resource at32_tcb1_resource[] = {
|
|
PBMEM(0xfff01000),
|
|
IRQ(23),
|
|
};
|
|
static struct platform_device at32_tcb1_device = {
|
|
.name = "atmel_tcb",
|
|
.id = 1,
|
|
.resource = at32_tcb1_resource,
|
|
.num_resources = ARRAY_SIZE(at32_tcb1_resource),
|
|
};
|
|
DEV_CLK(t0_clk, at32_tcb1, pbb, 4);
|
|
|
|
/* --------------------------------------------------------------------
|
|
* PIO
|
|
* -------------------------------------------------------------------- */
|
|
|
|
static struct resource pio0_resource[] = {
|
|
PBMEM(0xffe02800),
|
|
IRQ(13),
|
|
};
|
|
DEFINE_DEV(pio, 0);
|
|
DEV_CLK(mck, pio0, pba, 10);
|
|
|
|
static struct resource pio1_resource[] = {
|
|
PBMEM(0xffe02c00),
|
|
IRQ(14),
|
|
};
|
|
DEFINE_DEV(pio, 1);
|
|
DEV_CLK(mck, pio1, pba, 11);
|
|
|
|
static struct resource pio2_resource[] = {
|
|
PBMEM(0xffe03000),
|
|
IRQ(15),
|
|
};
|
|
DEFINE_DEV(pio, 2);
|
|
DEV_CLK(mck, pio2, pba, 12);
|
|
|
|
static struct resource pio3_resource[] = {
|
|
PBMEM(0xffe03400),
|
|
IRQ(16),
|
|
};
|
|
DEFINE_DEV(pio, 3);
|
|
DEV_CLK(mck, pio3, pba, 13);
|
|
|
|
static struct resource pio4_resource[] = {
|
|
PBMEM(0xffe03800),
|
|
IRQ(17),
|
|
};
|
|
DEFINE_DEV(pio, 4);
|
|
DEV_CLK(mck, pio4, pba, 14);
|
|
|
|
static int __init system_device_init(void)
|
|
{
|
|
platform_device_register(&at32_pm0_device);
|
|
platform_device_register(&at32_intc0_device);
|
|
platform_device_register(&at32ap700x_rtc0_device);
|
|
platform_device_register(&at32_wdt0_device);
|
|
platform_device_register(&at32_eic0_device);
|
|
platform_device_register(&smc0_device);
|
|
platform_device_register(&pdc_device);
|
|
platform_device_register(&dw_dmac0_device);
|
|
|
|
platform_device_register(&at32_tcb0_device);
|
|
platform_device_register(&at32_tcb1_device);
|
|
|
|
platform_device_register(&pio0_device);
|
|
platform_device_register(&pio1_device);
|
|
platform_device_register(&pio2_device);
|
|
platform_device_register(&pio3_device);
|
|
platform_device_register(&pio4_device);
|
|
|
|
return 0;
|
|
}
|
|
core_initcall(system_device_init);
|
|
|
|
/* --------------------------------------------------------------------
|
|
* PSIF
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource atmel_psif0_resource[] __initdata = {
|
|
{
|
|
.start = 0xffe03c00,
|
|
.end = 0xffe03cff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(18),
|
|
};
|
|
static struct clk atmel_psif0_pclk = {
|
|
.name = "pclk",
|
|
.parent = &pba_clk,
|
|
.mode = pba_clk_mode,
|
|
.get_rate = pba_clk_get_rate,
|
|
.index = 15,
|
|
};
|
|
|
|
static struct resource atmel_psif1_resource[] __initdata = {
|
|
{
|
|
.start = 0xffe03d00,
|
|
.end = 0xffe03dff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(18),
|
|
};
|
|
static struct clk atmel_psif1_pclk = {
|
|
.name = "pclk",
|
|
.parent = &pba_clk,
|
|
.mode = pba_clk_mode,
|
|
.get_rate = pba_clk_get_rate,
|
|
.index = 15,
|
|
};
|
|
|
|
struct platform_device *__init at32_add_device_psif(unsigned int id)
|
|
{
|
|
struct platform_device *pdev;
|
|
u32 pin_mask;
|
|
|
|
if (!(id == 0 || id == 1))
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_psif", id);
|
|
if (!pdev)
|
|
return NULL;
|
|
|
|
switch (id) {
|
|
case 0:
|
|
pin_mask = (1 << 8) | (1 << 9); /* CLOCK & DATA */
|
|
|
|
if (platform_device_add_resources(pdev, atmel_psif0_resource,
|
|
ARRAY_SIZE(atmel_psif0_resource)))
|
|
goto err_add_resources;
|
|
atmel_psif0_pclk.dev = &pdev->dev;
|
|
select_peripheral(PIOA, pin_mask, PERIPH_A, 0);
|
|
break;
|
|
case 1:
|
|
pin_mask = (1 << 11) | (1 << 12); /* CLOCK & DATA */
|
|
|
|
if (platform_device_add_resources(pdev, atmel_psif1_resource,
|
|
ARRAY_SIZE(atmel_psif1_resource)))
|
|
goto err_add_resources;
|
|
atmel_psif1_pclk.dev = &pdev->dev;
|
|
select_peripheral(PIOB, pin_mask, PERIPH_A, 0);
|
|
break;
|
|
default:
|
|
return NULL;
|
|
}
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
err_add_resources:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* USART
|
|
* -------------------------------------------------------------------- */
|
|
|
|
static struct atmel_uart_data atmel_usart0_data = {
|
|
.use_dma_tx = 1,
|
|
.use_dma_rx = 1,
|
|
};
|
|
static struct resource atmel_usart0_resource[] = {
|
|
PBMEM(0xffe00c00),
|
|
IRQ(6),
|
|
};
|
|
DEFINE_DEV_DATA(atmel_usart, 0);
|
|
DEV_CLK(usart, atmel_usart0, pba, 3);
|
|
|
|
static struct atmel_uart_data atmel_usart1_data = {
|
|
.use_dma_tx = 1,
|
|
.use_dma_rx = 1,
|
|
};
|
|
static struct resource atmel_usart1_resource[] = {
|
|
PBMEM(0xffe01000),
|
|
IRQ(7),
|
|
};
|
|
DEFINE_DEV_DATA(atmel_usart, 1);
|
|
DEV_CLK(usart, atmel_usart1, pba, 4);
|
|
|
|
static struct atmel_uart_data atmel_usart2_data = {
|
|
.use_dma_tx = 1,
|
|
.use_dma_rx = 1,
|
|
};
|
|
static struct resource atmel_usart2_resource[] = {
|
|
PBMEM(0xffe01400),
|
|
IRQ(8),
|
|
};
|
|
DEFINE_DEV_DATA(atmel_usart, 2);
|
|
DEV_CLK(usart, atmel_usart2, pba, 5);
|
|
|
|
static struct atmel_uart_data atmel_usart3_data = {
|
|
.use_dma_tx = 1,
|
|
.use_dma_rx = 1,
|
|
};
|
|
static struct resource atmel_usart3_resource[] = {
|
|
PBMEM(0xffe01800),
|
|
IRQ(9),
|
|
};
|
|
DEFINE_DEV_DATA(atmel_usart, 3);
|
|
DEV_CLK(usart, atmel_usart3, pba, 6);
|
|
|
|
static inline void configure_usart0_pins(int flags)
|
|
{
|
|
u32 pin_mask = (1 << 8) | (1 << 9); /* RXD & TXD */
|
|
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 6);
|
|
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 7);
|
|
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 10);
|
|
|
|
select_peripheral(PIOA, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
|
|
}
|
|
|
|
static inline void configure_usart1_pins(int flags)
|
|
{
|
|
u32 pin_mask = (1 << 17) | (1 << 18); /* RXD & TXD */
|
|
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 19);
|
|
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 20);
|
|
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 16);
|
|
|
|
select_peripheral(PIOA, pin_mask, PERIPH_A, AT32_GPIOF_PULLUP);
|
|
}
|
|
|
|
static inline void configure_usart2_pins(int flags)
|
|
{
|
|
u32 pin_mask = (1 << 26) | (1 << 27); /* RXD & TXD */
|
|
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 30);
|
|
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 29);
|
|
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 28);
|
|
|
|
select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
|
|
}
|
|
|
|
static inline void configure_usart3_pins(int flags)
|
|
{
|
|
u32 pin_mask = (1 << 18) | (1 << 17); /* RXD & TXD */
|
|
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 16);
|
|
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 15);
|
|
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 19);
|
|
|
|
select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
|
|
}
|
|
|
|
static struct platform_device *__initdata at32_usarts[4];
|
|
|
|
void __init at32_map_usart(unsigned int hw_id, unsigned int line, int flags)
|
|
{
|
|
struct platform_device *pdev;
|
|
struct atmel_uart_data *pdata;
|
|
|
|
switch (hw_id) {
|
|
case 0:
|
|
pdev = &atmel_usart0_device;
|
|
configure_usart0_pins(flags);
|
|
break;
|
|
case 1:
|
|
pdev = &atmel_usart1_device;
|
|
configure_usart1_pins(flags);
|
|
break;
|
|
case 2:
|
|
pdev = &atmel_usart2_device;
|
|
configure_usart2_pins(flags);
|
|
break;
|
|
case 3:
|
|
pdev = &atmel_usart3_device;
|
|
configure_usart3_pins(flags);
|
|
break;
|
|
default:
|
|
return;
|
|
}
|
|
|
|
if (PXSEG(pdev->resource[0].start) == P4SEG) {
|
|
/* Addresses in the P4 segment are permanently mapped 1:1 */
|
|
struct atmel_uart_data *data = pdev->dev.platform_data;
|
|
data->regs = (void __iomem *)pdev->resource[0].start;
|
|
}
|
|
|
|
pdev->id = line;
|
|
pdata = pdev->dev.platform_data;
|
|
pdata->num = line;
|
|
at32_usarts[line] = pdev;
|
|
}
|
|
|
|
struct platform_device *__init at32_add_device_usart(unsigned int id)
|
|
{
|
|
platform_device_register(at32_usarts[id]);
|
|
return at32_usarts[id];
|
|
}
|
|
|
|
void __init at32_setup_serial_console(unsigned int usart_id)
|
|
{
|
|
#ifdef CONFIG_SERIAL_ATMEL
|
|
atmel_default_console_device = at32_usarts[usart_id];
|
|
#endif
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* Ethernet
|
|
* -------------------------------------------------------------------- */
|
|
|
|
#ifdef CONFIG_CPU_AT32AP7000
|
|
static struct macb_platform_data macb0_data;
|
|
static struct resource macb0_resource[] = {
|
|
PBMEM(0xfff01800),
|
|
IRQ(25),
|
|
};
|
|
DEFINE_DEV_DATA(macb, 0);
|
|
DEV_CLK(hclk, macb0, hsb, 8);
|
|
DEV_CLK(pclk, macb0, pbb, 6);
|
|
|
|
static struct macb_platform_data macb1_data;
|
|
static struct resource macb1_resource[] = {
|
|
PBMEM(0xfff01c00),
|
|
IRQ(26),
|
|
};
|
|
DEFINE_DEV_DATA(macb, 1);
|
|
DEV_CLK(hclk, macb1, hsb, 9);
|
|
DEV_CLK(pclk, macb1, pbb, 7);
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_eth(unsigned int id, struct macb_platform_data *data)
|
|
{
|
|
struct platform_device *pdev;
|
|
u32 pin_mask;
|
|
|
|
switch (id) {
|
|
case 0:
|
|
pdev = &macb0_device;
|
|
|
|
pin_mask = (1 << 3); /* TXD0 */
|
|
pin_mask |= (1 << 4); /* TXD1 */
|
|
pin_mask |= (1 << 7); /* TXEN */
|
|
pin_mask |= (1 << 8); /* TXCK */
|
|
pin_mask |= (1 << 9); /* RXD0 */
|
|
pin_mask |= (1 << 10); /* RXD1 */
|
|
pin_mask |= (1 << 13); /* RXER */
|
|
pin_mask |= (1 << 15); /* RXDV */
|
|
pin_mask |= (1 << 16); /* MDC */
|
|
pin_mask |= (1 << 17); /* MDIO */
|
|
|
|
if (!data->is_rmii) {
|
|
pin_mask |= (1 << 0); /* COL */
|
|
pin_mask |= (1 << 1); /* CRS */
|
|
pin_mask |= (1 << 2); /* TXER */
|
|
pin_mask |= (1 << 5); /* TXD2 */
|
|
pin_mask |= (1 << 6); /* TXD3 */
|
|
pin_mask |= (1 << 11); /* RXD2 */
|
|
pin_mask |= (1 << 12); /* RXD3 */
|
|
pin_mask |= (1 << 14); /* RXCK */
|
|
#ifndef CONFIG_BOARD_MIMC200
|
|
pin_mask |= (1 << 18); /* SPD */
|
|
#endif
|
|
}
|
|
|
|
select_peripheral(PIOC, pin_mask, PERIPH_A, 0);
|
|
|
|
break;
|
|
|
|
case 1:
|
|
pdev = &macb1_device;
|
|
|
|
pin_mask = (1 << 13); /* TXD0 */
|
|
pin_mask |= (1 << 14); /* TXD1 */
|
|
pin_mask |= (1 << 11); /* TXEN */
|
|
pin_mask |= (1 << 12); /* TXCK */
|
|
pin_mask |= (1 << 10); /* RXD0 */
|
|
pin_mask |= (1 << 6); /* RXD1 */
|
|
pin_mask |= (1 << 5); /* RXER */
|
|
pin_mask |= (1 << 4); /* RXDV */
|
|
pin_mask |= (1 << 3); /* MDC */
|
|
pin_mask |= (1 << 2); /* MDIO */
|
|
|
|
#ifndef CONFIG_BOARD_MIMC200
|
|
if (!data->is_rmii)
|
|
pin_mask |= (1 << 15); /* SPD */
|
|
#endif
|
|
|
|
select_peripheral(PIOD, pin_mask, PERIPH_B, 0);
|
|
|
|
if (!data->is_rmii) {
|
|
pin_mask = (1 << 19); /* COL */
|
|
pin_mask |= (1 << 23); /* CRS */
|
|
pin_mask |= (1 << 26); /* TXER */
|
|
pin_mask |= (1 << 27); /* TXD2 */
|
|
pin_mask |= (1 << 28); /* TXD3 */
|
|
pin_mask |= (1 << 29); /* RXD2 */
|
|
pin_mask |= (1 << 30); /* RXD3 */
|
|
pin_mask |= (1 << 24); /* RXCK */
|
|
|
|
select_peripheral(PIOC, pin_mask, PERIPH_B, 0);
|
|
}
|
|
break;
|
|
|
|
default:
|
|
return NULL;
|
|
}
|
|
|
|
memcpy(pdev->dev.platform_data, data, sizeof(struct macb_platform_data));
|
|
platform_device_register(pdev);
|
|
|
|
return pdev;
|
|
}
|
|
#endif
|
|
|
|
/* --------------------------------------------------------------------
|
|
* SPI
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource atmel_spi0_resource[] = {
|
|
PBMEM(0xffe00000),
|
|
IRQ(3),
|
|
};
|
|
DEFINE_DEV(atmel_spi, 0);
|
|
DEV_CLK(spi_clk, atmel_spi0, pba, 0);
|
|
|
|
static struct resource atmel_spi1_resource[] = {
|
|
PBMEM(0xffe00400),
|
|
IRQ(4),
|
|
};
|
|
DEFINE_DEV(atmel_spi, 1);
|
|
DEV_CLK(spi_clk, atmel_spi1, pba, 1);
|
|
|
|
void __init
|
|
at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n)
|
|
{
|
|
/*
|
|
* Manage the chipselects as GPIOs, normally using the same pins
|
|
* the SPI controller expects; but boards can use other pins.
|
|
*/
|
|
static u8 __initdata spi_pins[][4] = {
|
|
{ GPIO_PIN_PA(3), GPIO_PIN_PA(4),
|
|
GPIO_PIN_PA(5), GPIO_PIN_PA(20) },
|
|
{ GPIO_PIN_PB(2), GPIO_PIN_PB(3),
|
|
GPIO_PIN_PB(4), GPIO_PIN_PA(27) },
|
|
};
|
|
unsigned int pin, mode;
|
|
|
|
/* There are only 2 SPI controllers */
|
|
if (bus_num > 1)
|
|
return;
|
|
|
|
for (; n; n--, b++) {
|
|
b->bus_num = bus_num;
|
|
if (b->chip_select >= 4)
|
|
continue;
|
|
pin = (unsigned)b->controller_data;
|
|
if (!pin) {
|
|
pin = spi_pins[bus_num][b->chip_select];
|
|
b->controller_data = (void *)pin;
|
|
}
|
|
mode = AT32_GPIOF_OUTPUT;
|
|
if (!(b->mode & SPI_CS_HIGH))
|
|
mode |= AT32_GPIOF_HIGH;
|
|
at32_select_gpio(pin, mode);
|
|
}
|
|
}
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n)
|
|
{
|
|
struct platform_device *pdev;
|
|
u32 pin_mask;
|
|
|
|
switch (id) {
|
|
case 0:
|
|
pdev = &atmel_spi0_device;
|
|
pin_mask = (1 << 1) | (1 << 2); /* MOSI & SCK */
|
|
|
|
/* pullup MISO so a level is always defined */
|
|
select_peripheral(PIOA, (1 << 0), PERIPH_A, AT32_GPIOF_PULLUP);
|
|
select_peripheral(PIOA, pin_mask, PERIPH_A, 0);
|
|
|
|
at32_spi_setup_slaves(0, b, n);
|
|
break;
|
|
|
|
case 1:
|
|
pdev = &atmel_spi1_device;
|
|
pin_mask = (1 << 1) | (1 << 5); /* MOSI */
|
|
|
|
/* pullup MISO so a level is always defined */
|
|
select_peripheral(PIOB, (1 << 0), PERIPH_B, AT32_GPIOF_PULLUP);
|
|
select_peripheral(PIOB, pin_mask, PERIPH_B, 0);
|
|
|
|
at32_spi_setup_slaves(1, b, n);
|
|
break;
|
|
|
|
default:
|
|
return NULL;
|
|
}
|
|
|
|
spi_register_board_info(b, n);
|
|
platform_device_register(pdev);
|
|
return pdev;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* TWI
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource atmel_twi0_resource[] __initdata = {
|
|
PBMEM(0xffe00800),
|
|
IRQ(5),
|
|
};
|
|
static struct clk atmel_twi0_pclk = {
|
|
.name = "twi_pclk",
|
|
.parent = &pba_clk,
|
|
.mode = pba_clk_mode,
|
|
.get_rate = pba_clk_get_rate,
|
|
.index = 2,
|
|
};
|
|
|
|
struct platform_device *__init at32_add_device_twi(unsigned int id,
|
|
struct i2c_board_info *b,
|
|
unsigned int n)
|
|
{
|
|
struct platform_device *pdev;
|
|
u32 pin_mask;
|
|
|
|
if (id != 0)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_twi", id);
|
|
if (!pdev)
|
|
return NULL;
|
|
|
|
if (platform_device_add_resources(pdev, atmel_twi0_resource,
|
|
ARRAY_SIZE(atmel_twi0_resource)))
|
|
goto err_add_resources;
|
|
|
|
pin_mask = (1 << 6) | (1 << 7); /* SDA & SDL */
|
|
|
|
select_peripheral(PIOA, pin_mask, PERIPH_A, 0);
|
|
|
|
atmel_twi0_pclk.dev = &pdev->dev;
|
|
|
|
if (b)
|
|
i2c_register_board_info(id, b, n);
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
err_add_resources:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* MMC
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource atmel_mci0_resource[] __initdata = {
|
|
PBMEM(0xfff02400),
|
|
IRQ(28),
|
|
};
|
|
static struct clk atmel_mci0_pclk = {
|
|
.name = "mci_clk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.index = 9,
|
|
};
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_mci(unsigned int id, struct mci_platform_data *data)
|
|
{
|
|
struct platform_device *pdev;
|
|
struct mci_dma_data *slave;
|
|
u32 pioa_mask;
|
|
u32 piob_mask;
|
|
|
|
if (id != 0 || !data)
|
|
return NULL;
|
|
|
|
/* Must have at least one usable slot */
|
|
if (!data->slot[0].bus_width && !data->slot[1].bus_width)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_mci", id);
|
|
if (!pdev)
|
|
goto fail;
|
|
|
|
if (platform_device_add_resources(pdev, atmel_mci0_resource,
|
|
ARRAY_SIZE(atmel_mci0_resource)))
|
|
goto fail;
|
|
|
|
slave = kzalloc(sizeof(struct mci_dma_data), GFP_KERNEL);
|
|
if (!slave)
|
|
goto fail;
|
|
|
|
slave->sdata.dma_dev = &dw_dmac0_device.dev;
|
|
slave->sdata.cfg_hi = (DWC_CFGH_SRC_PER(0)
|
|
| DWC_CFGH_DST_PER(1));
|
|
slave->sdata.cfg_lo &= ~(DWC_CFGL_HS_DST_POL
|
|
| DWC_CFGL_HS_SRC_POL);
|
|
|
|
data->dma_slave = slave;
|
|
|
|
if (platform_device_add_data(pdev, data,
|
|
sizeof(struct mci_platform_data)))
|
|
goto fail_free;
|
|
|
|
/* CLK line is common to both slots */
|
|
pioa_mask = 1 << 10;
|
|
|
|
switch (data->slot[0].bus_width) {
|
|
case 4:
|
|
pioa_mask |= 1 << 13; /* DATA1 */
|
|
pioa_mask |= 1 << 14; /* DATA2 */
|
|
pioa_mask |= 1 << 15; /* DATA3 */
|
|
/* fall through */
|
|
case 1:
|
|
pioa_mask |= 1 << 11; /* CMD */
|
|
pioa_mask |= 1 << 12; /* DATA0 */
|
|
|
|
if (gpio_is_valid(data->slot[0].detect_pin))
|
|
at32_select_gpio(data->slot[0].detect_pin, 0);
|
|
if (gpio_is_valid(data->slot[0].wp_pin))
|
|
at32_select_gpio(data->slot[0].wp_pin, 0);
|
|
break;
|
|
case 0:
|
|
/* Slot is unused */
|
|
break;
|
|
default:
|
|
goto fail_free;
|
|
}
|
|
|
|
select_peripheral(PIOA, pioa_mask, PERIPH_A, 0);
|
|
piob_mask = 0;
|
|
|
|
switch (data->slot[1].bus_width) {
|
|
case 4:
|
|
piob_mask |= 1 << 8; /* DATA1 */
|
|
piob_mask |= 1 << 9; /* DATA2 */
|
|
piob_mask |= 1 << 10; /* DATA3 */
|
|
/* fall through */
|
|
case 1:
|
|
piob_mask |= 1 << 6; /* CMD */
|
|
piob_mask |= 1 << 7; /* DATA0 */
|
|
select_peripheral(PIOB, piob_mask, PERIPH_B, 0);
|
|
|
|
if (gpio_is_valid(data->slot[1].detect_pin))
|
|
at32_select_gpio(data->slot[1].detect_pin, 0);
|
|
if (gpio_is_valid(data->slot[1].wp_pin))
|
|
at32_select_gpio(data->slot[1].wp_pin, 0);
|
|
break;
|
|
case 0:
|
|
/* Slot is unused */
|
|
break;
|
|
default:
|
|
if (!data->slot[0].bus_width)
|
|
goto fail_free;
|
|
|
|
data->slot[1].bus_width = 0;
|
|
break;
|
|
}
|
|
|
|
atmel_mci0_pclk.dev = &pdev->dev;
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
fail_free:
|
|
kfree(slave);
|
|
fail:
|
|
data->dma_slave = NULL;
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* LCDC
|
|
* -------------------------------------------------------------------- */
|
|
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
|
|
static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
|
|
static struct resource atmel_lcdfb0_resource[] = {
|
|
{
|
|
.start = 0xff000000,
|
|
.end = 0xff000fff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(1),
|
|
{
|
|
/* Placeholder for pre-allocated fb memory */
|
|
.start = 0x00000000,
|
|
.end = 0x00000000,
|
|
.flags = 0,
|
|
},
|
|
};
|
|
DEFINE_DEV_DATA(atmel_lcdfb, 0);
|
|
DEV_CLK(hclk, atmel_lcdfb0, hsb, 7);
|
|
static struct clk atmel_lcdfb0_pixclk = {
|
|
.name = "lcdc_clk",
|
|
.dev = &atmel_lcdfb0_device.dev,
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 7,
|
|
};
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
|
|
unsigned long fbmem_start, unsigned long fbmem_len,
|
|
u64 pin_mask)
|
|
{
|
|
struct platform_device *pdev;
|
|
struct atmel_lcdfb_pdata *info;
|
|
struct fb_monspecs *monspecs;
|
|
struct fb_videomode *modedb;
|
|
unsigned int modedb_size;
|
|
u32 portc_mask, portd_mask, porte_mask;
|
|
|
|
/*
|
|
* Do a deep copy of the fb data, monspecs and modedb. Make
|
|
* sure all allocations are done before setting up the
|
|
* portmux.
|
|
*/
|
|
monspecs = kmemdup(data->default_monspecs,
|
|
sizeof(struct fb_monspecs), GFP_KERNEL);
|
|
if (!monspecs)
|
|
return NULL;
|
|
|
|
modedb_size = sizeof(struct fb_videomode) * monspecs->modedb_len;
|
|
modedb = kmemdup(monspecs->modedb, modedb_size, GFP_KERNEL);
|
|
if (!modedb)
|
|
goto err_dup_modedb;
|
|
monspecs->modedb = modedb;
|
|
|
|
switch (id) {
|
|
case 0:
|
|
pdev = &atmel_lcdfb0_device;
|
|
|
|
if (pin_mask == 0ULL)
|
|
/* Default to "full" lcdc control signals and 24bit */
|
|
pin_mask = ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL;
|
|
|
|
/* LCDC on port C */
|
|
portc_mask = pin_mask & 0xfff80000;
|
|
select_peripheral(PIOC, portc_mask, PERIPH_A, 0);
|
|
|
|
/* LCDC on port D */
|
|
portd_mask = pin_mask & 0x0003ffff;
|
|
select_peripheral(PIOD, portd_mask, PERIPH_A, 0);
|
|
|
|
/* LCDC on port E */
|
|
porte_mask = (pin_mask >> 32) & 0x0007ffff;
|
|
select_peripheral(PIOE, porte_mask, PERIPH_B, 0);
|
|
|
|
clk_set_parent(&atmel_lcdfb0_pixclk, &pll0);
|
|
clk_set_rate(&atmel_lcdfb0_pixclk, clk_get_rate(&pll0));
|
|
break;
|
|
|
|
default:
|
|
goto err_invalid_id;
|
|
}
|
|
|
|
if (fbmem_len) {
|
|
pdev->resource[2].start = fbmem_start;
|
|
pdev->resource[2].end = fbmem_start + fbmem_len - 1;
|
|
pdev->resource[2].flags = IORESOURCE_MEM;
|
|
}
|
|
|
|
info = pdev->dev.platform_data;
|
|
memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
|
|
info->default_monspecs = monspecs;
|
|
|
|
pdev->name = "at32ap-lcdfb";
|
|
|
|
platform_device_register(pdev);
|
|
return pdev;
|
|
|
|
err_invalid_id:
|
|
kfree(modedb);
|
|
err_dup_modedb:
|
|
kfree(monspecs);
|
|
return NULL;
|
|
}
|
|
#endif
|
|
|
|
/* --------------------------------------------------------------------
|
|
* PWM
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource atmel_pwm0_resource[] __initdata = {
|
|
PBMEM(0xfff01400),
|
|
IRQ(24),
|
|
};
|
|
static struct clk atmel_pwm0_mck = {
|
|
.name = "pwm_clk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.index = 5,
|
|
};
|
|
|
|
struct platform_device *__init at32_add_device_pwm(u32 mask)
|
|
{
|
|
struct platform_device *pdev;
|
|
u32 pin_mask;
|
|
|
|
if (!mask)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_pwm", 0);
|
|
if (!pdev)
|
|
return NULL;
|
|
|
|
if (platform_device_add_resources(pdev, atmel_pwm0_resource,
|
|
ARRAY_SIZE(atmel_pwm0_resource)))
|
|
goto out_free_pdev;
|
|
|
|
if (platform_device_add_data(pdev, &mask, sizeof(mask)))
|
|
goto out_free_pdev;
|
|
|
|
pin_mask = 0;
|
|
if (mask & (1 << 0))
|
|
pin_mask |= (1 << 28);
|
|
if (mask & (1 << 1))
|
|
pin_mask |= (1 << 29);
|
|
if (pin_mask > 0)
|
|
select_peripheral(PIOA, pin_mask, PERIPH_A, 0);
|
|
|
|
pin_mask = 0;
|
|
if (mask & (1 << 2))
|
|
pin_mask |= (1 << 21);
|
|
if (mask & (1 << 3))
|
|
pin_mask |= (1 << 22);
|
|
if (pin_mask > 0)
|
|
select_peripheral(PIOA, pin_mask, PERIPH_B, 0);
|
|
|
|
atmel_pwm0_mck.dev = &pdev->dev;
|
|
|
|
platform_device_add(pdev);
|
|
|
|
return pdev;
|
|
|
|
out_free_pdev:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* SSC
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource ssc0_resource[] = {
|
|
PBMEM(0xffe01c00),
|
|
IRQ(10),
|
|
};
|
|
DEFINE_DEV(ssc, 0);
|
|
DEV_CLK(pclk, ssc0, pba, 7);
|
|
|
|
static struct resource ssc1_resource[] = {
|
|
PBMEM(0xffe02000),
|
|
IRQ(11),
|
|
};
|
|
DEFINE_DEV(ssc, 1);
|
|
DEV_CLK(pclk, ssc1, pba, 8);
|
|
|
|
static struct resource ssc2_resource[] = {
|
|
PBMEM(0xffe02400),
|
|
IRQ(12),
|
|
};
|
|
DEFINE_DEV(ssc, 2);
|
|
DEV_CLK(pclk, ssc2, pba, 9);
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_ssc(unsigned int id, unsigned int flags)
|
|
{
|
|
struct platform_device *pdev;
|
|
u32 pin_mask = 0;
|
|
|
|
switch (id) {
|
|
case 0:
|
|
pdev = &ssc0_device;
|
|
if (flags & ATMEL_SSC_RF)
|
|
pin_mask |= (1 << 21); /* RF */
|
|
if (flags & ATMEL_SSC_RK)
|
|
pin_mask |= (1 << 22); /* RK */
|
|
if (flags & ATMEL_SSC_TK)
|
|
pin_mask |= (1 << 23); /* TK */
|
|
if (flags & ATMEL_SSC_TF)
|
|
pin_mask |= (1 << 24); /* TF */
|
|
if (flags & ATMEL_SSC_TD)
|
|
pin_mask |= (1 << 25); /* TD */
|
|
if (flags & ATMEL_SSC_RD)
|
|
pin_mask |= (1 << 26); /* RD */
|
|
|
|
if (pin_mask > 0)
|
|
select_peripheral(PIOA, pin_mask, PERIPH_A, 0);
|
|
|
|
break;
|
|
case 1:
|
|
pdev = &ssc1_device;
|
|
if (flags & ATMEL_SSC_RF)
|
|
pin_mask |= (1 << 0); /* RF */
|
|
if (flags & ATMEL_SSC_RK)
|
|
pin_mask |= (1 << 1); /* RK */
|
|
if (flags & ATMEL_SSC_TK)
|
|
pin_mask |= (1 << 2); /* TK */
|
|
if (flags & ATMEL_SSC_TF)
|
|
pin_mask |= (1 << 3); /* TF */
|
|
if (flags & ATMEL_SSC_TD)
|
|
pin_mask |= (1 << 4); /* TD */
|
|
if (flags & ATMEL_SSC_RD)
|
|
pin_mask |= (1 << 5); /* RD */
|
|
|
|
if (pin_mask > 0)
|
|
select_peripheral(PIOA, pin_mask, PERIPH_B, 0);
|
|
|
|
break;
|
|
case 2:
|
|
pdev = &ssc2_device;
|
|
if (flags & ATMEL_SSC_TD)
|
|
pin_mask |= (1 << 13); /* TD */
|
|
if (flags & ATMEL_SSC_RD)
|
|
pin_mask |= (1 << 14); /* RD */
|
|
if (flags & ATMEL_SSC_TK)
|
|
pin_mask |= (1 << 15); /* TK */
|
|
if (flags & ATMEL_SSC_TF)
|
|
pin_mask |= (1 << 16); /* TF */
|
|
if (flags & ATMEL_SSC_RF)
|
|
pin_mask |= (1 << 17); /* RF */
|
|
if (flags & ATMEL_SSC_RK)
|
|
pin_mask |= (1 << 18); /* RK */
|
|
|
|
if (pin_mask > 0)
|
|
select_peripheral(PIOB, pin_mask, PERIPH_A, 0);
|
|
|
|
break;
|
|
default:
|
|
return NULL;
|
|
}
|
|
|
|
platform_device_register(pdev);
|
|
return pdev;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* USB Device Controller
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource usba0_resource[] __initdata = {
|
|
{
|
|
.start = 0xff300000,
|
|
.end = 0xff3fffff,
|
|
.flags = IORESOURCE_MEM,
|
|
}, {
|
|
.start = 0xfff03000,
|
|
.end = 0xfff033ff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(31),
|
|
};
|
|
static struct clk usba0_pclk = {
|
|
.name = "pclk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.index = 12,
|
|
};
|
|
static struct clk usba0_hclk = {
|
|
.name = "hclk",
|
|
.parent = &hsb_clk,
|
|
.mode = hsb_clk_mode,
|
|
.get_rate = hsb_clk_get_rate,
|
|
.index = 6,
|
|
};
|
|
|
|
#define EP(nam, idx, maxpkt, maxbk, dma, isoc) \
|
|
[idx] = { \
|
|
.name = nam, \
|
|
.index = idx, \
|
|
.fifo_size = maxpkt, \
|
|
.nr_banks = maxbk, \
|
|
.can_dma = dma, \
|
|
.can_isoc = isoc, \
|
|
}
|
|
|
|
static struct usba_ep_data at32_usba_ep[] __initdata = {
|
|
EP("ep0", 0, 64, 1, 0, 0),
|
|
EP("ep1", 1, 512, 2, 1, 1),
|
|
EP("ep2", 2, 512, 2, 1, 1),
|
|
EP("ep3-int", 3, 64, 3, 1, 0),
|
|
EP("ep4-int", 4, 64, 3, 1, 0),
|
|
EP("ep5", 5, 1024, 3, 1, 1),
|
|
EP("ep6", 6, 1024, 3, 1, 1),
|
|
};
|
|
|
|
#undef EP
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_usba(unsigned int id, struct usba_platform_data *data)
|
|
{
|
|
/*
|
|
* pdata doesn't have room for any endpoints, so we need to
|
|
* append room for the ones we need right after it.
|
|
*/
|
|
struct {
|
|
struct usba_platform_data pdata;
|
|
struct usba_ep_data ep[7];
|
|
} usba_data;
|
|
struct platform_device *pdev;
|
|
|
|
if (id != 0)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_usba_udc", 0);
|
|
if (!pdev)
|
|
return NULL;
|
|
|
|
if (platform_device_add_resources(pdev, usba0_resource,
|
|
ARRAY_SIZE(usba0_resource)))
|
|
goto out_free_pdev;
|
|
|
|
if (data) {
|
|
usba_data.pdata.vbus_pin = data->vbus_pin;
|
|
usba_data.pdata.vbus_pin_inverted = data->vbus_pin_inverted;
|
|
} else {
|
|
usba_data.pdata.vbus_pin = -EINVAL;
|
|
usba_data.pdata.vbus_pin_inverted = -EINVAL;
|
|
}
|
|
|
|
data = &usba_data.pdata;
|
|
data->num_ep = ARRAY_SIZE(at32_usba_ep);
|
|
memcpy(data->ep, at32_usba_ep, sizeof(at32_usba_ep));
|
|
|
|
if (platform_device_add_data(pdev, data, sizeof(usba_data)))
|
|
goto out_free_pdev;
|
|
|
|
if (gpio_is_valid(data->vbus_pin))
|
|
at32_select_gpio(data->vbus_pin, 0);
|
|
|
|
usba0_pclk.dev = &pdev->dev;
|
|
usba0_hclk.dev = &pdev->dev;
|
|
|
|
platform_device_add(pdev);
|
|
|
|
return pdev;
|
|
|
|
out_free_pdev:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* IDE / CompactFlash
|
|
* -------------------------------------------------------------------- */
|
|
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7001)
|
|
static struct resource at32_smc_cs4_resource[] __initdata = {
|
|
{
|
|
.start = 0x04000000,
|
|
.end = 0x07ffffff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(~0UL), /* Magic IRQ will be overridden */
|
|
};
|
|
static struct resource at32_smc_cs5_resource[] __initdata = {
|
|
{
|
|
.start = 0x20000000,
|
|
.end = 0x23ffffff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
IRQ(~0UL), /* Magic IRQ will be overridden */
|
|
};
|
|
|
|
static int __init at32_init_ide_or_cf(struct platform_device *pdev,
|
|
unsigned int cs, unsigned int extint)
|
|
{
|
|
static unsigned int extint_pin_map[4] __initdata = {
|
|
(1 << 25),
|
|
(1 << 26),
|
|
(1 << 27),
|
|
(1 << 28),
|
|
};
|
|
static bool common_pins_initialized __initdata = false;
|
|
unsigned int extint_pin;
|
|
int ret;
|
|
u32 pin_mask;
|
|
|
|
if (extint >= ARRAY_SIZE(extint_pin_map))
|
|
return -EINVAL;
|
|
extint_pin = extint_pin_map[extint];
|
|
|
|
switch (cs) {
|
|
case 4:
|
|
ret = platform_device_add_resources(pdev,
|
|
at32_smc_cs4_resource,
|
|
ARRAY_SIZE(at32_smc_cs4_resource));
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* NCS4 -> OE_N */
|
|
select_peripheral(PIOE, (1 << 21), PERIPH_A, 0);
|
|
hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF0_ENABLE);
|
|
break;
|
|
case 5:
|
|
ret = platform_device_add_resources(pdev,
|
|
at32_smc_cs5_resource,
|
|
ARRAY_SIZE(at32_smc_cs5_resource));
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* NCS5 -> OE_N */
|
|
select_peripheral(PIOE, (1 << 22), PERIPH_A, 0);
|
|
hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_CF1_ENABLE);
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (!common_pins_initialized) {
|
|
pin_mask = (1 << 19); /* CFCE1 -> CS0_N */
|
|
pin_mask |= (1 << 20); /* CFCE2 -> CS1_N */
|
|
pin_mask |= (1 << 23); /* CFRNW -> DIR */
|
|
pin_mask |= (1 << 24); /* NWAIT <- IORDY */
|
|
|
|
select_peripheral(PIOE, pin_mask, PERIPH_A, 0);
|
|
|
|
common_pins_initialized = true;
|
|
}
|
|
|
|
select_peripheral(PIOB, extint_pin, PERIPH_A, AT32_GPIOF_DEGLITCH);
|
|
|
|
pdev->resource[1].start = EIM_IRQ_BASE + extint;
|
|
pdev->resource[1].end = pdev->resource[1].start;
|
|
|
|
return 0;
|
|
}
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_ide(unsigned int id, unsigned int extint,
|
|
struct ide_platform_data *data)
|
|
{
|
|
struct platform_device *pdev;
|
|
|
|
pdev = platform_device_alloc("at32_ide", id);
|
|
if (!pdev)
|
|
goto fail;
|
|
|
|
if (platform_device_add_data(pdev, data,
|
|
sizeof(struct ide_platform_data)))
|
|
goto fail;
|
|
|
|
if (at32_init_ide_or_cf(pdev, data->cs, extint))
|
|
goto fail;
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
fail:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_cf(unsigned int id, unsigned int extint,
|
|
struct cf_platform_data *data)
|
|
{
|
|
struct platform_device *pdev;
|
|
|
|
pdev = platform_device_alloc("at32_cf", id);
|
|
if (!pdev)
|
|
goto fail;
|
|
|
|
if (platform_device_add_data(pdev, data,
|
|
sizeof(struct cf_platform_data)))
|
|
goto fail;
|
|
|
|
if (at32_init_ide_or_cf(pdev, data->cs, extint))
|
|
goto fail;
|
|
|
|
if (gpio_is_valid(data->detect_pin))
|
|
at32_select_gpio(data->detect_pin, AT32_GPIOF_DEGLITCH);
|
|
if (gpio_is_valid(data->reset_pin))
|
|
at32_select_gpio(data->reset_pin, 0);
|
|
if (gpio_is_valid(data->vcc_pin))
|
|
at32_select_gpio(data->vcc_pin, 0);
|
|
/* READY is used as extint, so we can't select it as gpio */
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
fail:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
#endif
|
|
|
|
/* --------------------------------------------------------------------
|
|
* NAND Flash / SmartMedia
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource smc_cs3_resource[] __initdata = {
|
|
{
|
|
.start = 0x0c000000,
|
|
.end = 0x0fffffff,
|
|
.flags = IORESOURCE_MEM,
|
|
}, {
|
|
.start = 0xfff03c00,
|
|
.end = 0xfff03fff,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_nand(unsigned int id, struct atmel_nand_data *data)
|
|
{
|
|
struct platform_device *pdev;
|
|
|
|
if (id != 0 || !data)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_nand", id);
|
|
if (!pdev)
|
|
goto fail;
|
|
|
|
if (platform_device_add_resources(pdev, smc_cs3_resource,
|
|
ARRAY_SIZE(smc_cs3_resource)))
|
|
goto fail;
|
|
|
|
/* For at32ap7000, we use the reset workaround for nand driver */
|
|
data->need_reset_workaround = true;
|
|
|
|
if (platform_device_add_data(pdev, data,
|
|
sizeof(struct atmel_nand_data)))
|
|
goto fail;
|
|
|
|
hmatrix_sfr_set_bits(HMATRIX_SLAVE_EBI, HMATRIX_EBI_NAND_ENABLE);
|
|
if (data->enable_pin)
|
|
at32_select_gpio(data->enable_pin,
|
|
AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
|
|
if (data->rdy_pin)
|
|
at32_select_gpio(data->rdy_pin, 0);
|
|
if (data->det_pin)
|
|
at32_select_gpio(data->det_pin, 0);
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
fail:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* AC97C
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource atmel_ac97c0_resource[] __initdata = {
|
|
PBMEM(0xfff02800),
|
|
IRQ(29),
|
|
};
|
|
static struct clk atmel_ac97c0_pclk = {
|
|
.name = "pclk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.index = 10,
|
|
};
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_ac97c(unsigned int id, struct ac97c_platform_data *data,
|
|
unsigned int flags)
|
|
{
|
|
struct platform_device *pdev;
|
|
struct dw_dma_slave *rx_dws;
|
|
struct dw_dma_slave *tx_dws;
|
|
struct ac97c_platform_data _data;
|
|
u32 pin_mask;
|
|
|
|
if (id != 0)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_ac97c", id);
|
|
if (!pdev)
|
|
return NULL;
|
|
|
|
if (platform_device_add_resources(pdev, atmel_ac97c0_resource,
|
|
ARRAY_SIZE(atmel_ac97c0_resource)))
|
|
goto out_free_resources;
|
|
|
|
if (!data) {
|
|
data = &_data;
|
|
memset(data, 0, sizeof(struct ac97c_platform_data));
|
|
data->reset_pin = -ENODEV;
|
|
}
|
|
|
|
rx_dws = &data->rx_dws;
|
|
tx_dws = &data->tx_dws;
|
|
|
|
/* Check if DMA slave interface for capture should be configured. */
|
|
if (flags & AC97C_CAPTURE) {
|
|
rx_dws->dma_dev = &dw_dmac0_device.dev;
|
|
rx_dws->cfg_hi = DWC_CFGH_SRC_PER(3);
|
|
rx_dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL | DWC_CFGL_HS_SRC_POL);
|
|
rx_dws->src_master = 0;
|
|
rx_dws->dst_master = 1;
|
|
}
|
|
|
|
/* Check if DMA slave interface for playback should be configured. */
|
|
if (flags & AC97C_PLAYBACK) {
|
|
tx_dws->dma_dev = &dw_dmac0_device.dev;
|
|
tx_dws->cfg_hi = DWC_CFGH_DST_PER(4);
|
|
tx_dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL | DWC_CFGL_HS_SRC_POL);
|
|
tx_dws->src_master = 0;
|
|
tx_dws->dst_master = 1;
|
|
}
|
|
|
|
if (platform_device_add_data(pdev, data,
|
|
sizeof(struct ac97c_platform_data)))
|
|
goto out_free_resources;
|
|
|
|
/* SDO | SYNC | SCLK | SDI */
|
|
pin_mask = (1 << 20) | (1 << 21) | (1 << 22) | (1 << 23);
|
|
|
|
select_peripheral(PIOB, pin_mask, PERIPH_B, 0);
|
|
|
|
if (gpio_is_valid(data->reset_pin))
|
|
at32_select_gpio(data->reset_pin, AT32_GPIOF_OUTPUT
|
|
| AT32_GPIOF_HIGH);
|
|
|
|
atmel_ac97c0_pclk.dev = &pdev->dev;
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
out_free_resources:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* ABDAC
|
|
* -------------------------------------------------------------------- */
|
|
static struct resource abdac0_resource[] __initdata = {
|
|
PBMEM(0xfff02000),
|
|
IRQ(27),
|
|
};
|
|
static struct clk abdac0_pclk = {
|
|
.name = "pclk",
|
|
.parent = &pbb_clk,
|
|
.mode = pbb_clk_mode,
|
|
.get_rate = pbb_clk_get_rate,
|
|
.index = 8,
|
|
};
|
|
static struct clk abdac0_sample_clk = {
|
|
.name = "sample_clk",
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 6,
|
|
};
|
|
|
|
struct platform_device *__init
|
|
at32_add_device_abdac(unsigned int id, struct atmel_abdac_pdata *data)
|
|
{
|
|
struct platform_device *pdev;
|
|
struct dw_dma_slave *dws;
|
|
u32 pin_mask;
|
|
|
|
if (id != 0 || !data)
|
|
return NULL;
|
|
|
|
pdev = platform_device_alloc("atmel_abdac", id);
|
|
if (!pdev)
|
|
return NULL;
|
|
|
|
if (platform_device_add_resources(pdev, abdac0_resource,
|
|
ARRAY_SIZE(abdac0_resource)))
|
|
goto out_free_resources;
|
|
|
|
dws = &data->dws;
|
|
|
|
dws->dma_dev = &dw_dmac0_device.dev;
|
|
dws->cfg_hi = DWC_CFGH_DST_PER(2);
|
|
dws->cfg_lo &= ~(DWC_CFGL_HS_DST_POL | DWC_CFGL_HS_SRC_POL);
|
|
dws->src_master = 0;
|
|
dws->dst_master = 1;
|
|
|
|
if (platform_device_add_data(pdev, data,
|
|
sizeof(struct atmel_abdac_pdata)))
|
|
goto out_free_resources;
|
|
|
|
pin_mask = (1 << 20) | (1 << 22); /* DATA1 & DATAN1 */
|
|
pin_mask |= (1 << 21) | (1 << 23); /* DATA0 & DATAN0 */
|
|
|
|
select_peripheral(PIOB, pin_mask, PERIPH_A, 0);
|
|
|
|
abdac0_pclk.dev = &pdev->dev;
|
|
abdac0_sample_clk.dev = &pdev->dev;
|
|
|
|
platform_device_add(pdev);
|
|
return pdev;
|
|
|
|
out_free_resources:
|
|
platform_device_put(pdev);
|
|
return NULL;
|
|
}
|
|
|
|
/* --------------------------------------------------------------------
|
|
* GCLK
|
|
* -------------------------------------------------------------------- */
|
|
static struct clk gclk0 = {
|
|
.name = "gclk0",
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 0,
|
|
};
|
|
static struct clk gclk1 = {
|
|
.name = "gclk1",
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 1,
|
|
};
|
|
static struct clk gclk2 = {
|
|
.name = "gclk2",
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 2,
|
|
};
|
|
static struct clk gclk3 = {
|
|
.name = "gclk3",
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 3,
|
|
};
|
|
static struct clk gclk4 = {
|
|
.name = "gclk4",
|
|
.mode = genclk_mode,
|
|
.get_rate = genclk_get_rate,
|
|
.set_rate = genclk_set_rate,
|
|
.set_parent = genclk_set_parent,
|
|
.index = 4,
|
|
};
|
|
|
|
static __initdata struct clk *init_clocks[] = {
|
|
&osc32k,
|
|
&osc0,
|
|
&osc1,
|
|
&pll0,
|
|
&pll1,
|
|
&cpu_clk,
|
|
&hsb_clk,
|
|
&pba_clk,
|
|
&pbb_clk,
|
|
&at32_pm_pclk,
|
|
&at32_intc0_pclk,
|
|
&at32_hmatrix_clk,
|
|
&ebi_clk,
|
|
&hramc_clk,
|
|
&sdramc_clk,
|
|
&smc0_pclk,
|
|
&smc0_mck,
|
|
&pdc_hclk,
|
|
&pdc_pclk,
|
|
&dw_dmac0_hclk,
|
|
&pico_clk,
|
|
&pio0_mck,
|
|
&pio1_mck,
|
|
&pio2_mck,
|
|
&pio3_mck,
|
|
&pio4_mck,
|
|
&at32_tcb0_t0_clk,
|
|
&at32_tcb1_t0_clk,
|
|
&atmel_psif0_pclk,
|
|
&atmel_psif1_pclk,
|
|
&atmel_usart0_usart,
|
|
&atmel_usart1_usart,
|
|
&atmel_usart2_usart,
|
|
&atmel_usart3_usart,
|
|
&atmel_pwm0_mck,
|
|
#if defined(CONFIG_CPU_AT32AP7000)
|
|
&macb0_hclk,
|
|
&macb0_pclk,
|
|
&macb1_hclk,
|
|
&macb1_pclk,
|
|
#endif
|
|
&atmel_spi0_spi_clk,
|
|
&atmel_spi1_spi_clk,
|
|
&atmel_twi0_pclk,
|
|
&atmel_mci0_pclk,
|
|
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
|
|
&atmel_lcdfb0_hclk,
|
|
&atmel_lcdfb0_pixclk,
|
|
#endif
|
|
&ssc0_pclk,
|
|
&ssc1_pclk,
|
|
&ssc2_pclk,
|
|
&usba0_hclk,
|
|
&usba0_pclk,
|
|
&atmel_ac97c0_pclk,
|
|
&abdac0_pclk,
|
|
&abdac0_sample_clk,
|
|
&gclk0,
|
|
&gclk1,
|
|
&gclk2,
|
|
&gclk3,
|
|
&gclk4,
|
|
};
|
|
|
|
void __init setup_platform(void)
|
|
{
|
|
u32 cpu_mask = 0, hsb_mask = 0, pba_mask = 0, pbb_mask = 0;
|
|
int i;
|
|
|
|
if (pm_readl(MCCTRL) & PM_BIT(PLLSEL)) {
|
|
main_clock = &pll0;
|
|
cpu_clk.parent = &pll0;
|
|
} else {
|
|
main_clock = &osc0;
|
|
cpu_clk.parent = &osc0;
|
|
}
|
|
|
|
if (pm_readl(PLL0) & PM_BIT(PLLOSC))
|
|
pll0.parent = &osc1;
|
|
if (pm_readl(PLL1) & PM_BIT(PLLOSC))
|
|
pll1.parent = &osc1;
|
|
|
|
genclk_init_parent(&gclk0);
|
|
genclk_init_parent(&gclk1);
|
|
genclk_init_parent(&gclk2);
|
|
genclk_init_parent(&gclk3);
|
|
genclk_init_parent(&gclk4);
|
|
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
|
|
genclk_init_parent(&atmel_lcdfb0_pixclk);
|
|
#endif
|
|
genclk_init_parent(&abdac0_sample_clk);
|
|
|
|
/*
|
|
* Build initial dynamic clock list by registering all clocks
|
|
* from the array.
|
|
* At the same time, turn on all clocks that have at least one
|
|
* user already, and turn off everything else. We only do this
|
|
* for module clocks, and even though it isn't particularly
|
|
* pretty to check the address of the mode function, it should
|
|
* do the trick...
|
|
*/
|
|
for (i = 0; i < ARRAY_SIZE(init_clocks); i++) {
|
|
struct clk *clk = init_clocks[i];
|
|
|
|
/* first, register clock */
|
|
at32_clk_register(clk);
|
|
|
|
if (clk->users == 0)
|
|
continue;
|
|
|
|
if (clk->mode == &cpu_clk_mode)
|
|
cpu_mask |= 1 << clk->index;
|
|
else if (clk->mode == &hsb_clk_mode)
|
|
hsb_mask |= 1 << clk->index;
|
|
else if (clk->mode == &pba_clk_mode)
|
|
pba_mask |= 1 << clk->index;
|
|
else if (clk->mode == &pbb_clk_mode)
|
|
pbb_mask |= 1 << clk->index;
|
|
}
|
|
|
|
pm_writel(CPU_MASK, cpu_mask);
|
|
pm_writel(HSB_MASK, hsb_mask);
|
|
pm_writel(PBA_MASK, pba_mask);
|
|
pm_writel(PBB_MASK, pbb_mask);
|
|
|
|
/* Initialize the port muxes */
|
|
at32_init_pio(&pio0_device);
|
|
at32_init_pio(&pio1_device);
|
|
at32_init_pio(&pio2_device);
|
|
at32_init_pio(&pio3_device);
|
|
at32_init_pio(&pio4_device);
|
|
}
|
|
|
|
struct gen_pool *sram_pool;
|
|
|
|
static int __init sram_init(void)
|
|
{
|
|
struct gen_pool *pool;
|
|
|
|
/* 1KiB granularity */
|
|
pool = gen_pool_create(10, -1);
|
|
if (!pool)
|
|
goto fail;
|
|
|
|
if (gen_pool_add(pool, 0x24000000, 0x8000, -1))
|
|
goto err_pool_add;
|
|
|
|
sram_pool = pool;
|
|
return 0;
|
|
|
|
err_pool_add:
|
|
gen_pool_destroy(pool);
|
|
fail:
|
|
pr_err("Failed to create SRAM pool\n");
|
|
return -ENOMEM;
|
|
}
|
|
core_initcall(sram_init);
|