92 lines
3.2 KiB
Plaintext
92 lines
3.2 KiB
Plaintext
* SPI NOR flash: ST M25Pxx (and similar) serial flash chips
|
|
|
|
Required properties:
|
|
- #address-cells, #size-cells : Must be present if the device has sub-nodes
|
|
representing partitions.
|
|
- compatible : May include a device-specific string consisting of the
|
|
manufacturer and name of the chip. A list of supported chip
|
|
names follows.
|
|
Must also include "jedec,spi-nor" for any SPI NOR flash that can
|
|
be identified by the JEDEC READ ID opcode (0x9F).
|
|
|
|
Supported chip names:
|
|
at25df321a
|
|
at25df641
|
|
at26df081a
|
|
mr25h128
|
|
mr25h256
|
|
mr25h10
|
|
mr25h40
|
|
mx25l4005a
|
|
mx25l1606e
|
|
mx25l6405d
|
|
mx25l12805d
|
|
mx25l25635e
|
|
n25q064
|
|
n25q128a11
|
|
n25q128a13
|
|
n25q512a
|
|
s25fl256s1
|
|
s25fl512s
|
|
s25sl12801
|
|
s25fl008k
|
|
s25fl064k
|
|
sst25vf040b
|
|
m25p40
|
|
m25p80
|
|
m25p16
|
|
m25p32
|
|
m25p64
|
|
m25p128
|
|
w25x80
|
|
w25x32
|
|
w25q32
|
|
w25q64
|
|
w25q32dw
|
|
w25q80bl
|
|
w25q128
|
|
w25q256
|
|
|
|
The following chip names have been used historically to
|
|
designate quirky versions of flash chips that do not support the
|
|
JEDEC READ ID opcode (0x9F):
|
|
m25p05-nonjedec
|
|
m25p10-nonjedec
|
|
m25p20-nonjedec
|
|
m25p40-nonjedec
|
|
m25p80-nonjedec
|
|
m25p16-nonjedec
|
|
m25p32-nonjedec
|
|
m25p64-nonjedec
|
|
m25p128-nonjedec
|
|
|
|
- reg : Chip-Select number
|
|
- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
|
|
|
|
Optional properties:
|
|
- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead
|
|
of the usual "read" opcode. This opcode is not supported by
|
|
all chips and support for it can not be detected at runtime.
|
|
Refer to your chips' datasheet to check if this is supported
|
|
by your chip.
|
|
- broken-flash-reset : Some flash devices utilize stateful addressing modes
|
|
(e.g., for 32-bit addressing) which need to be managed
|
|
carefully by a system. Because these sorts of flash don't
|
|
have a standardized software reset command, and because some
|
|
systems don't toggle the flash RESET# pin upon system reset
|
|
(if the pin even exists at all), there are systems which
|
|
cannot reboot properly if the flash is left in the "wrong"
|
|
state. This boolean flag can be used on such systems, to
|
|
denote the absence of a reliable reset mechanism.
|
|
|
|
Example:
|
|
|
|
flash: m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "spansion,m25p80", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
m25p,fast-read;
|
|
};
|