1732 lines
38 KiB
C
1732 lines
38 KiB
C
/*
|
|
* Copyright (c) 2009-2013, The Linux Foundation. All rights reserved.
|
|
* Copyright (c) 2014, Sony Mobile Communications AB.
|
|
*
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
*/
|
|
|
|
#include <linux/acpi.h>
|
|
#include <linux/atomic.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/dmaengine.h>
|
|
#include <linux/dmapool.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/err.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/scatterlist.h>
|
|
|
|
/* QUP Registers */
|
|
#define QUP_CONFIG 0x000
|
|
#define QUP_STATE 0x004
|
|
#define QUP_IO_MODE 0x008
|
|
#define QUP_SW_RESET 0x00c
|
|
#define QUP_OPERATIONAL 0x018
|
|
#define QUP_ERROR_FLAGS 0x01c
|
|
#define QUP_ERROR_FLAGS_EN 0x020
|
|
#define QUP_OPERATIONAL_MASK 0x028
|
|
#define QUP_HW_VERSION 0x030
|
|
#define QUP_MX_OUTPUT_CNT 0x100
|
|
#define QUP_OUT_FIFO_BASE 0x110
|
|
#define QUP_MX_WRITE_CNT 0x150
|
|
#define QUP_MX_INPUT_CNT 0x200
|
|
#define QUP_MX_READ_CNT 0x208
|
|
#define QUP_IN_FIFO_BASE 0x218
|
|
#define QUP_I2C_CLK_CTL 0x400
|
|
#define QUP_I2C_STATUS 0x404
|
|
#define QUP_I2C_MASTER_GEN 0x408
|
|
|
|
/* QUP States and reset values */
|
|
#define QUP_RESET_STATE 0
|
|
#define QUP_RUN_STATE 1
|
|
#define QUP_PAUSE_STATE 3
|
|
#define QUP_STATE_MASK 3
|
|
|
|
#define QUP_STATE_VALID BIT(2)
|
|
#define QUP_I2C_MAST_GEN BIT(4)
|
|
#define QUP_I2C_FLUSH BIT(6)
|
|
|
|
#define QUP_OPERATIONAL_RESET 0x000ff0
|
|
#define QUP_I2C_STATUS_RESET 0xfffffc
|
|
|
|
/* QUP OPERATIONAL FLAGS */
|
|
#define QUP_I2C_NACK_FLAG BIT(3)
|
|
#define QUP_OUT_NOT_EMPTY BIT(4)
|
|
#define QUP_IN_NOT_EMPTY BIT(5)
|
|
#define QUP_OUT_FULL BIT(6)
|
|
#define QUP_OUT_SVC_FLAG BIT(8)
|
|
#define QUP_IN_SVC_FLAG BIT(9)
|
|
#define QUP_MX_OUTPUT_DONE BIT(10)
|
|
#define QUP_MX_INPUT_DONE BIT(11)
|
|
|
|
/* I2C mini core related values */
|
|
#define QUP_CLOCK_AUTO_GATE BIT(13)
|
|
#define I2C_MINI_CORE (2 << 8)
|
|
#define I2C_N_VAL 15
|
|
#define I2C_N_VAL_V2 7
|
|
|
|
/* Most significant word offset in FIFO port */
|
|
#define QUP_MSW_SHIFT (I2C_N_VAL + 1)
|
|
|
|
/* Packing/Unpacking words in FIFOs, and IO modes */
|
|
#define QUP_OUTPUT_BLK_MODE (1 << 10)
|
|
#define QUP_OUTPUT_BAM_MODE (3 << 10)
|
|
#define QUP_INPUT_BLK_MODE (1 << 12)
|
|
#define QUP_INPUT_BAM_MODE (3 << 12)
|
|
#define QUP_BAM_MODE (QUP_OUTPUT_BAM_MODE | QUP_INPUT_BAM_MODE)
|
|
#define QUP_UNPACK_EN BIT(14)
|
|
#define QUP_PACK_EN BIT(15)
|
|
|
|
#define QUP_REPACK_EN (QUP_UNPACK_EN | QUP_PACK_EN)
|
|
#define QUP_V2_TAGS_EN 1
|
|
|
|
#define QUP_OUTPUT_BLOCK_SIZE(x)(((x) >> 0) & 0x03)
|
|
#define QUP_OUTPUT_FIFO_SIZE(x) (((x) >> 2) & 0x07)
|
|
#define QUP_INPUT_BLOCK_SIZE(x) (((x) >> 5) & 0x03)
|
|
#define QUP_INPUT_FIFO_SIZE(x) (((x) >> 7) & 0x07)
|
|
|
|
/* QUP tags */
|
|
#define QUP_TAG_START (1 << 8)
|
|
#define QUP_TAG_DATA (2 << 8)
|
|
#define QUP_TAG_STOP (3 << 8)
|
|
#define QUP_TAG_REC (4 << 8)
|
|
#define QUP_BAM_INPUT_EOT 0x93
|
|
#define QUP_BAM_FLUSH_STOP 0x96
|
|
|
|
/* QUP v2 tags */
|
|
#define QUP_TAG_V2_START 0x81
|
|
#define QUP_TAG_V2_DATAWR 0x82
|
|
#define QUP_TAG_V2_DATAWR_STOP 0x83
|
|
#define QUP_TAG_V2_DATARD 0x85
|
|
#define QUP_TAG_V2_DATARD_STOP 0x87
|
|
|
|
/* Status, Error flags */
|
|
#define I2C_STATUS_WR_BUFFER_FULL BIT(0)
|
|
#define I2C_STATUS_BUS_ACTIVE BIT(8)
|
|
#define I2C_STATUS_ERROR_MASK 0x38000fc
|
|
#define QUP_STATUS_ERROR_FLAGS 0x7c
|
|
|
|
#define QUP_READ_LIMIT 256
|
|
#define SET_BIT 0x1
|
|
#define RESET_BIT 0x0
|
|
#define ONE_BYTE 0x1
|
|
#define QUP_I2C_MX_CONFIG_DURING_RUN BIT(31)
|
|
|
|
#define MX_TX_RX_LEN SZ_64K
|
|
#define MX_BLOCKS (MX_TX_RX_LEN / QUP_READ_LIMIT)
|
|
|
|
/* Max timeout in ms for 32k bytes */
|
|
#define TOUT_MAX 300
|
|
|
|
/* Default values. Use these if FW query fails */
|
|
#define DEFAULT_CLK_FREQ 100000
|
|
#define DEFAULT_SRC_CLK 20000000
|
|
|
|
struct qup_i2c_block {
|
|
int count;
|
|
int pos;
|
|
int tx_tag_len;
|
|
int rx_tag_len;
|
|
int data_len;
|
|
u8 tags[6];
|
|
};
|
|
|
|
struct qup_i2c_tag {
|
|
u8 *start;
|
|
dma_addr_t addr;
|
|
};
|
|
|
|
struct qup_i2c_bam {
|
|
struct qup_i2c_tag tag;
|
|
struct dma_chan *dma;
|
|
struct scatterlist *sg;
|
|
};
|
|
|
|
struct qup_i2c_dev {
|
|
struct device *dev;
|
|
void __iomem *base;
|
|
int irq;
|
|
struct clk *clk;
|
|
struct clk *pclk;
|
|
struct i2c_adapter adap;
|
|
|
|
int clk_ctl;
|
|
int out_fifo_sz;
|
|
int in_fifo_sz;
|
|
int out_blk_sz;
|
|
int in_blk_sz;
|
|
|
|
unsigned long one_byte_t;
|
|
struct qup_i2c_block blk;
|
|
|
|
struct i2c_msg *msg;
|
|
/* Current posion in user message buffer */
|
|
int pos;
|
|
/* I2C protocol errors */
|
|
u32 bus_err;
|
|
/* QUP core errors */
|
|
u32 qup_err;
|
|
|
|
/* To check if this is the last msg */
|
|
bool is_last;
|
|
|
|
/* To configure when bus is in run state */
|
|
int config_run;
|
|
|
|
/* dma parameters */
|
|
bool is_dma;
|
|
struct dma_pool *dpool;
|
|
struct qup_i2c_tag start_tag;
|
|
struct qup_i2c_bam brx;
|
|
struct qup_i2c_bam btx;
|
|
|
|
struct completion xfer;
|
|
};
|
|
|
|
static irqreturn_t qup_i2c_interrupt(int irq, void *dev)
|
|
{
|
|
struct qup_i2c_dev *qup = dev;
|
|
u32 bus_err;
|
|
u32 qup_err;
|
|
u32 opflags;
|
|
|
|
bus_err = readl(qup->base + QUP_I2C_STATUS);
|
|
qup_err = readl(qup->base + QUP_ERROR_FLAGS);
|
|
opflags = readl(qup->base + QUP_OPERATIONAL);
|
|
|
|
if (!qup->msg) {
|
|
/* Clear Error interrupt */
|
|
writel(QUP_RESET_STATE, qup->base + QUP_STATE);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
bus_err &= I2C_STATUS_ERROR_MASK;
|
|
qup_err &= QUP_STATUS_ERROR_FLAGS;
|
|
|
|
/* Clear the error bits in QUP_ERROR_FLAGS */
|
|
if (qup_err)
|
|
writel(qup_err, qup->base + QUP_ERROR_FLAGS);
|
|
|
|
/* Clear the error bits in QUP_I2C_STATUS */
|
|
if (bus_err)
|
|
writel(bus_err, qup->base + QUP_I2C_STATUS);
|
|
|
|
/* Reset the QUP State in case of error */
|
|
if (qup_err || bus_err) {
|
|
writel(QUP_RESET_STATE, qup->base + QUP_STATE);
|
|
goto done;
|
|
}
|
|
|
|
if (opflags & QUP_IN_SVC_FLAG)
|
|
writel(QUP_IN_SVC_FLAG, qup->base + QUP_OPERATIONAL);
|
|
|
|
if (opflags & QUP_OUT_SVC_FLAG)
|
|
writel(QUP_OUT_SVC_FLAG, qup->base + QUP_OPERATIONAL);
|
|
|
|
done:
|
|
qup->qup_err = qup_err;
|
|
qup->bus_err = bus_err;
|
|
complete(&qup->xfer);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int qup_i2c_poll_state_mask(struct qup_i2c_dev *qup,
|
|
u32 req_state, u32 req_mask)
|
|
{
|
|
int retries = 1;
|
|
u32 state;
|
|
|
|
/*
|
|
* State transition takes 3 AHB clocks cycles + 3 I2C master clock
|
|
* cycles. So retry once after a 1uS delay.
|
|
*/
|
|
do {
|
|
state = readl(qup->base + QUP_STATE);
|
|
|
|
if (state & QUP_STATE_VALID &&
|
|
(state & req_mask) == req_state)
|
|
return 0;
|
|
|
|
udelay(1);
|
|
} while (retries--);
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static int qup_i2c_poll_state(struct qup_i2c_dev *qup, u32 req_state)
|
|
{
|
|
return qup_i2c_poll_state_mask(qup, req_state, QUP_STATE_MASK);
|
|
}
|
|
|
|
static void qup_i2c_flush(struct qup_i2c_dev *qup)
|
|
{
|
|
u32 val = readl(qup->base + QUP_STATE);
|
|
|
|
val |= QUP_I2C_FLUSH;
|
|
writel(val, qup->base + QUP_STATE);
|
|
}
|
|
|
|
static int qup_i2c_poll_state_valid(struct qup_i2c_dev *qup)
|
|
{
|
|
return qup_i2c_poll_state_mask(qup, 0, 0);
|
|
}
|
|
|
|
static int qup_i2c_poll_state_i2c_master(struct qup_i2c_dev *qup)
|
|
{
|
|
return qup_i2c_poll_state_mask(qup, QUP_I2C_MAST_GEN, QUP_I2C_MAST_GEN);
|
|
}
|
|
|
|
static int qup_i2c_change_state(struct qup_i2c_dev *qup, u32 state)
|
|
{
|
|
if (qup_i2c_poll_state_valid(qup) != 0)
|
|
return -EIO;
|
|
|
|
writel(state, qup->base + QUP_STATE);
|
|
|
|
if (qup_i2c_poll_state(qup, state) != 0)
|
|
return -EIO;
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* qup_i2c_wait_ready - wait for a give number of bytes in tx/rx path
|
|
* @qup: The qup_i2c_dev device
|
|
* @op: The bit/event to wait on
|
|
* @val: value of the bit to wait on, 0 or 1
|
|
* @len: The length the bytes to be transferred
|
|
*/
|
|
static int qup_i2c_wait_ready(struct qup_i2c_dev *qup, int op, bool val,
|
|
int len)
|
|
{
|
|
unsigned long timeout;
|
|
u32 opflags;
|
|
u32 status;
|
|
u32 shift = __ffs(op);
|
|
int ret = 0;
|
|
|
|
len *= qup->one_byte_t;
|
|
/* timeout after a wait of twice the max time */
|
|
timeout = jiffies + len * 4;
|
|
|
|
for (;;) {
|
|
opflags = readl(qup->base + QUP_OPERATIONAL);
|
|
status = readl(qup->base + QUP_I2C_STATUS);
|
|
|
|
if (((opflags & op) >> shift) == val) {
|
|
if ((op == QUP_OUT_NOT_EMPTY) && qup->is_last) {
|
|
if (!(status & I2C_STATUS_BUS_ACTIVE)) {
|
|
ret = 0;
|
|
goto done;
|
|
}
|
|
} else {
|
|
ret = 0;
|
|
goto done;
|
|
}
|
|
}
|
|
|
|
if (time_after(jiffies, timeout)) {
|
|
ret = -ETIMEDOUT;
|
|
goto done;
|
|
}
|
|
usleep_range(len, len * 2);
|
|
}
|
|
|
|
done:
|
|
if (qup->bus_err || qup->qup_err)
|
|
ret = (qup->bus_err & QUP_I2C_NACK_FLAG) ? -ENXIO : -EIO;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void qup_i2c_set_write_mode_v2(struct qup_i2c_dev *qup,
|
|
struct i2c_msg *msg)
|
|
{
|
|
/* Number of entries to shift out, including the tags */
|
|
int total = msg->len + qup->blk.tx_tag_len;
|
|
|
|
total |= qup->config_run;
|
|
|
|
if (total < qup->out_fifo_sz) {
|
|
/* FIFO mode */
|
|
writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
|
|
writel(total, qup->base + QUP_MX_WRITE_CNT);
|
|
} else {
|
|
/* BLOCK mode (transfer data on chunks) */
|
|
writel(QUP_OUTPUT_BLK_MODE | QUP_REPACK_EN,
|
|
qup->base + QUP_IO_MODE);
|
|
writel(total, qup->base + QUP_MX_OUTPUT_CNT);
|
|
}
|
|
}
|
|
|
|
static void qup_i2c_set_write_mode(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
/* Number of entries to shift out, including the start */
|
|
int total = msg->len + 1;
|
|
|
|
if (total < qup->out_fifo_sz) {
|
|
/* FIFO mode */
|
|
writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
|
|
writel(total, qup->base + QUP_MX_WRITE_CNT);
|
|
} else {
|
|
/* BLOCK mode (transfer data on chunks) */
|
|
writel(QUP_OUTPUT_BLK_MODE | QUP_REPACK_EN,
|
|
qup->base + QUP_IO_MODE);
|
|
writel(total, qup->base + QUP_MX_OUTPUT_CNT);
|
|
}
|
|
}
|
|
|
|
static int check_for_fifo_space(struct qup_i2c_dev *qup)
|
|
{
|
|
int ret;
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = qup_i2c_wait_ready(qup, QUP_OUT_FULL,
|
|
RESET_BIT, 4 * ONE_BYTE);
|
|
if (ret) {
|
|
/* Fifo is full. Drain out the fifo */
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto out;
|
|
|
|
ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY,
|
|
RESET_BIT, 256 * ONE_BYTE);
|
|
if (ret) {
|
|
dev_err(qup->dev, "timeout for fifo out full");
|
|
goto out;
|
|
}
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
|
if (ret)
|
|
goto out;
|
|
}
|
|
|
|
out:
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_issue_write(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
u32 addr = msg->addr << 1;
|
|
u32 qup_tag;
|
|
int idx;
|
|
u32 val;
|
|
int ret = 0;
|
|
|
|
if (qup->pos == 0) {
|
|
val = QUP_TAG_START | addr;
|
|
idx = 1;
|
|
} else {
|
|
val = 0;
|
|
idx = 0;
|
|
}
|
|
|
|
while (qup->pos < msg->len) {
|
|
/* Check that there's space in the FIFO for our pair */
|
|
ret = check_for_fifo_space(qup);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (qup->pos == msg->len - 1)
|
|
qup_tag = QUP_TAG_STOP;
|
|
else
|
|
qup_tag = QUP_TAG_DATA;
|
|
|
|
if (idx & 1)
|
|
val |= (qup_tag | msg->buf[qup->pos]) << QUP_MSW_SHIFT;
|
|
else
|
|
val = qup_tag | msg->buf[qup->pos];
|
|
|
|
/* Write out the pair and the last odd value */
|
|
if (idx & 1 || qup->pos == msg->len - 1)
|
|
writel(val, qup->base + QUP_OUT_FIFO_BASE);
|
|
|
|
qup->pos++;
|
|
idx++;
|
|
}
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void qup_i2c_set_blk_data(struct qup_i2c_dev *qup,
|
|
struct i2c_msg *msg)
|
|
{
|
|
memset(&qup->blk, 0, sizeof(qup->blk));
|
|
|
|
qup->blk.data_len = msg->len;
|
|
qup->blk.count = (msg->len + QUP_READ_LIMIT - 1) / QUP_READ_LIMIT;
|
|
|
|
/* 4 bytes for first block and 2 writes for rest */
|
|
qup->blk.tx_tag_len = 4 + (qup->blk.count - 1) * 2;
|
|
|
|
/* There are 2 tag bytes that are read in to fifo for every block */
|
|
if (msg->flags & I2C_M_RD)
|
|
qup->blk.rx_tag_len = qup->blk.count * 2;
|
|
}
|
|
|
|
static int qup_i2c_send_data(struct qup_i2c_dev *qup, int tlen, u8 *tbuf,
|
|
int dlen, u8 *dbuf)
|
|
{
|
|
u32 val = 0, idx = 0, pos = 0, i = 0, t;
|
|
int len = tlen + dlen;
|
|
u8 *buf = tbuf;
|
|
int ret = 0;
|
|
|
|
while (len > 0) {
|
|
ret = check_for_fifo_space(qup);
|
|
if (ret)
|
|
return ret;
|
|
|
|
t = (len >= 4) ? 4 : len;
|
|
|
|
while (idx < t) {
|
|
if (!i && (pos >= tlen)) {
|
|
buf = dbuf;
|
|
pos = 0;
|
|
i = 1;
|
|
}
|
|
val |= buf[pos++] << (idx++ * 8);
|
|
}
|
|
|
|
writel(val, qup->base + QUP_OUT_FIFO_BASE);
|
|
idx = 0;
|
|
val = 0;
|
|
len -= 4;
|
|
}
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_get_data_len(struct qup_i2c_dev *qup)
|
|
{
|
|
int data_len;
|
|
|
|
if (qup->blk.data_len > QUP_READ_LIMIT)
|
|
data_len = QUP_READ_LIMIT;
|
|
else
|
|
data_len = qup->blk.data_len;
|
|
|
|
return data_len;
|
|
}
|
|
|
|
static bool qup_i2c_check_msg_len(struct i2c_msg *msg)
|
|
{
|
|
return ((msg->flags & I2C_M_RD) && (msg->flags & I2C_M_RECV_LEN));
|
|
}
|
|
|
|
static int qup_i2c_set_tags_smb(u16 addr, u8 *tags, struct qup_i2c_dev *qup,
|
|
struct i2c_msg *msg)
|
|
{
|
|
int len = 0;
|
|
|
|
if (msg->len > 1) {
|
|
tags[len++] = QUP_TAG_V2_DATARD_STOP;
|
|
tags[len++] = qup_i2c_get_data_len(qup) - 1;
|
|
} else {
|
|
tags[len++] = QUP_TAG_V2_START;
|
|
tags[len++] = addr & 0xff;
|
|
|
|
if (msg->flags & I2C_M_TEN)
|
|
tags[len++] = addr >> 8;
|
|
|
|
tags[len++] = QUP_TAG_V2_DATARD;
|
|
/* Read 1 byte indicating the length of the SMBus message */
|
|
tags[len++] = 1;
|
|
}
|
|
return len;
|
|
}
|
|
|
|
static int qup_i2c_set_tags(u8 *tags, struct qup_i2c_dev *qup,
|
|
struct i2c_msg *msg, int is_dma)
|
|
{
|
|
u16 addr = i2c_8bit_addr_from_msg(msg);
|
|
int len = 0;
|
|
int data_len;
|
|
|
|
int last = (qup->blk.pos == (qup->blk.count - 1)) && (qup->is_last);
|
|
|
|
/* Handle tags for SMBus block read */
|
|
if (qup_i2c_check_msg_len(msg))
|
|
return qup_i2c_set_tags_smb(addr, tags, qup, msg);
|
|
|
|
if (qup->blk.pos == 0) {
|
|
tags[len++] = QUP_TAG_V2_START;
|
|
tags[len++] = addr & 0xff;
|
|
|
|
if (msg->flags & I2C_M_TEN)
|
|
tags[len++] = addr >> 8;
|
|
}
|
|
|
|
/* Send _STOP commands for the last block */
|
|
if (last) {
|
|
if (msg->flags & I2C_M_RD)
|
|
tags[len++] = QUP_TAG_V2_DATARD_STOP;
|
|
else
|
|
tags[len++] = QUP_TAG_V2_DATAWR_STOP;
|
|
} else {
|
|
if (msg->flags & I2C_M_RD)
|
|
tags[len++] = QUP_TAG_V2_DATARD;
|
|
else
|
|
tags[len++] = QUP_TAG_V2_DATAWR;
|
|
}
|
|
|
|
data_len = qup_i2c_get_data_len(qup);
|
|
|
|
/* 0 implies 256 bytes */
|
|
if (data_len == QUP_READ_LIMIT)
|
|
tags[len++] = 0;
|
|
else
|
|
tags[len++] = data_len;
|
|
|
|
if ((msg->flags & I2C_M_RD) && last && is_dma) {
|
|
tags[len++] = QUP_BAM_INPUT_EOT;
|
|
tags[len++] = QUP_BAM_FLUSH_STOP;
|
|
}
|
|
|
|
return len;
|
|
}
|
|
|
|
static int qup_i2c_issue_xfer_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
int data_len = 0, tag_len, index;
|
|
int ret;
|
|
|
|
tag_len = qup_i2c_set_tags(qup->blk.tags, qup, msg, 0);
|
|
index = msg->len - qup->blk.data_len;
|
|
|
|
/* only tags are written for read */
|
|
if (!(msg->flags & I2C_M_RD))
|
|
data_len = qup_i2c_get_data_len(qup);
|
|
|
|
ret = qup_i2c_send_data(qup, tag_len, qup->blk.tags,
|
|
data_len, &msg->buf[index]);
|
|
qup->blk.data_len -= data_len;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void qup_i2c_bam_cb(void *data)
|
|
{
|
|
struct qup_i2c_dev *qup = data;
|
|
|
|
complete(&qup->xfer);
|
|
}
|
|
|
|
static int qup_sg_set_buf(struct scatterlist *sg, void *buf,
|
|
unsigned int buflen, struct qup_i2c_dev *qup,
|
|
int dir)
|
|
{
|
|
int ret;
|
|
|
|
sg_set_buf(sg, buf, buflen);
|
|
ret = dma_map_sg(qup->dev, sg, 1, dir);
|
|
if (!ret)
|
|
return -EINVAL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void qup_i2c_rel_dma(struct qup_i2c_dev *qup)
|
|
{
|
|
if (qup->btx.dma)
|
|
dma_release_channel(qup->btx.dma);
|
|
if (qup->brx.dma)
|
|
dma_release_channel(qup->brx.dma);
|
|
qup->btx.dma = NULL;
|
|
qup->brx.dma = NULL;
|
|
}
|
|
|
|
static int qup_i2c_req_dma(struct qup_i2c_dev *qup)
|
|
{
|
|
int err;
|
|
|
|
if (!qup->btx.dma) {
|
|
qup->btx.dma = dma_request_slave_channel_reason(qup->dev, "tx");
|
|
if (IS_ERR(qup->btx.dma)) {
|
|
err = PTR_ERR(qup->btx.dma);
|
|
qup->btx.dma = NULL;
|
|
dev_err(qup->dev, "\n tx channel not available");
|
|
return err;
|
|
}
|
|
}
|
|
|
|
if (!qup->brx.dma) {
|
|
qup->brx.dma = dma_request_slave_channel_reason(qup->dev, "rx");
|
|
if (IS_ERR(qup->brx.dma)) {
|
|
dev_err(qup->dev, "\n rx channel not available");
|
|
err = PTR_ERR(qup->brx.dma);
|
|
qup->brx.dma = NULL;
|
|
qup_i2c_rel_dma(qup);
|
|
return err;
|
|
}
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int qup_i2c_bam_do_xfer(struct qup_i2c_dev *qup, struct i2c_msg *msg,
|
|
int num)
|
|
{
|
|
struct dma_async_tx_descriptor *txd, *rxd = NULL;
|
|
int ret = 0, idx = 0, limit = QUP_READ_LIMIT;
|
|
dma_cookie_t cookie_rx, cookie_tx;
|
|
u32 rx_nents = 0, tx_nents = 0, len, blocks, rem;
|
|
u32 i, tlen, tx_len, tx_buf = 0, rx_buf = 0, off = 0;
|
|
u8 *tags;
|
|
|
|
while (idx < num) {
|
|
tx_len = 0, len = 0, i = 0;
|
|
|
|
qup->is_last = (idx == (num - 1));
|
|
|
|
qup_i2c_set_blk_data(qup, msg);
|
|
|
|
blocks = qup->blk.count;
|
|
rem = msg->len - (blocks - 1) * limit;
|
|
|
|
if (msg->flags & I2C_M_RD) {
|
|
rx_nents += (blocks * 2) + 1;
|
|
tx_nents += 1;
|
|
|
|
while (qup->blk.pos < blocks) {
|
|
tlen = (i == (blocks - 1)) ? rem : limit;
|
|
tags = &qup->start_tag.start[off + len];
|
|
len += qup_i2c_set_tags(tags, qup, msg, 1);
|
|
qup->blk.data_len -= tlen;
|
|
|
|
/* scratch buf to read the start and len tags */
|
|
ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++],
|
|
&qup->brx.tag.start[0],
|
|
2, qup, DMA_FROM_DEVICE);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++],
|
|
&msg->buf[limit * i],
|
|
tlen, qup,
|
|
DMA_FROM_DEVICE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
i++;
|
|
qup->blk.pos = i;
|
|
}
|
|
ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++],
|
|
&qup->start_tag.start[off],
|
|
len, qup, DMA_TO_DEVICE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
off += len;
|
|
/* scratch buf to read the BAM EOT and FLUSH tags */
|
|
ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++],
|
|
&qup->brx.tag.start[0],
|
|
2, qup, DMA_FROM_DEVICE);
|
|
if (ret)
|
|
return ret;
|
|
} else {
|
|
tx_nents += (blocks * 2);
|
|
|
|
while (qup->blk.pos < blocks) {
|
|
tlen = (i == (blocks - 1)) ? rem : limit;
|
|
tags = &qup->start_tag.start[off + tx_len];
|
|
len = qup_i2c_set_tags(tags, qup, msg, 1);
|
|
qup->blk.data_len -= tlen;
|
|
|
|
ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++],
|
|
tags, len,
|
|
qup, DMA_TO_DEVICE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
tx_len += len;
|
|
ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++],
|
|
&msg->buf[limit * i],
|
|
tlen, qup, DMA_TO_DEVICE);
|
|
if (ret)
|
|
return ret;
|
|
i++;
|
|
qup->blk.pos = i;
|
|
}
|
|
off += tx_len;
|
|
|
|
if (idx == (num - 1)) {
|
|
len = 1;
|
|
if (rx_nents) {
|
|
qup->btx.tag.start[0] =
|
|
QUP_BAM_INPUT_EOT;
|
|
len++;
|
|
}
|
|
qup->btx.tag.start[len - 1] =
|
|
QUP_BAM_FLUSH_STOP;
|
|
ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++],
|
|
&qup->btx.tag.start[0],
|
|
len, qup, DMA_TO_DEVICE);
|
|
if (ret)
|
|
return ret;
|
|
tx_nents += 1;
|
|
}
|
|
}
|
|
idx++;
|
|
msg++;
|
|
}
|
|
|
|
txd = dmaengine_prep_slave_sg(qup->btx.dma, qup->btx.sg, tx_nents,
|
|
DMA_MEM_TO_DEV,
|
|
DMA_PREP_INTERRUPT | DMA_PREP_FENCE);
|
|
if (!txd) {
|
|
dev_err(qup->dev, "failed to get tx desc\n");
|
|
ret = -EINVAL;
|
|
goto desc_err;
|
|
}
|
|
|
|
if (!rx_nents) {
|
|
txd->callback = qup_i2c_bam_cb;
|
|
txd->callback_param = qup;
|
|
}
|
|
|
|
cookie_tx = dmaengine_submit(txd);
|
|
if (dma_submit_error(cookie_tx)) {
|
|
ret = -EINVAL;
|
|
goto desc_err;
|
|
}
|
|
|
|
dma_async_issue_pending(qup->btx.dma);
|
|
|
|
if (rx_nents) {
|
|
rxd = dmaengine_prep_slave_sg(qup->brx.dma, qup->brx.sg,
|
|
rx_nents, DMA_DEV_TO_MEM,
|
|
DMA_PREP_INTERRUPT);
|
|
if (!rxd) {
|
|
dev_err(qup->dev, "failed to get rx desc\n");
|
|
ret = -EINVAL;
|
|
|
|
/* abort TX descriptors */
|
|
dmaengine_terminate_all(qup->btx.dma);
|
|
goto desc_err;
|
|
}
|
|
|
|
rxd->callback = qup_i2c_bam_cb;
|
|
rxd->callback_param = qup;
|
|
cookie_rx = dmaengine_submit(rxd);
|
|
if (dma_submit_error(cookie_rx)) {
|
|
ret = -EINVAL;
|
|
goto desc_err;
|
|
}
|
|
|
|
dma_async_issue_pending(qup->brx.dma);
|
|
}
|
|
|
|
if (!wait_for_completion_timeout(&qup->xfer, TOUT_MAX * HZ)) {
|
|
dev_err(qup->dev, "normal trans timed out\n");
|
|
ret = -ETIMEDOUT;
|
|
}
|
|
|
|
if (ret || qup->bus_err || qup->qup_err) {
|
|
if (qup_i2c_change_state(qup, QUP_RUN_STATE)) {
|
|
dev_err(qup->dev, "change to run state timed out");
|
|
goto desc_err;
|
|
}
|
|
|
|
if (rx_nents)
|
|
writel(QUP_BAM_INPUT_EOT,
|
|
qup->base + QUP_OUT_FIFO_BASE);
|
|
|
|
writel(QUP_BAM_FLUSH_STOP, qup->base + QUP_OUT_FIFO_BASE);
|
|
|
|
qup_i2c_flush(qup);
|
|
|
|
/* wait for remaining interrupts to occur */
|
|
if (!wait_for_completion_timeout(&qup->xfer, HZ))
|
|
dev_err(qup->dev, "flush timed out\n");
|
|
|
|
qup_i2c_rel_dma(qup);
|
|
|
|
ret = (qup->bus_err & QUP_I2C_NACK_FLAG) ? -ENXIO : -EIO;
|
|
}
|
|
|
|
desc_err:
|
|
dma_unmap_sg(qup->dev, qup->btx.sg, tx_nents, DMA_TO_DEVICE);
|
|
|
|
if (rx_nents)
|
|
dma_unmap_sg(qup->dev, qup->brx.sg, rx_nents,
|
|
DMA_FROM_DEVICE);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_bam_xfer(struct i2c_adapter *adap, struct i2c_msg *msg,
|
|
int num)
|
|
{
|
|
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
|
|
int ret = 0;
|
|
|
|
enable_irq(qup->irq);
|
|
ret = qup_i2c_req_dma(qup);
|
|
|
|
if (ret)
|
|
goto out;
|
|
|
|
writel(0, qup->base + QUP_MX_INPUT_CNT);
|
|
writel(0, qup->base + QUP_MX_OUTPUT_CNT);
|
|
|
|
/* set BAM mode */
|
|
writel(QUP_REPACK_EN | QUP_BAM_MODE, qup->base + QUP_IO_MODE);
|
|
|
|
/* mask fifo irqs */
|
|
writel((0x3 << 8), qup->base + QUP_OPERATIONAL_MASK);
|
|
|
|
/* set RUN STATE */
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto out;
|
|
|
|
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
|
|
|
qup->msg = msg;
|
|
ret = qup_i2c_bam_do_xfer(qup, qup->msg, num);
|
|
out:
|
|
disable_irq(qup->irq);
|
|
|
|
qup->msg = NULL;
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_wait_for_complete(struct qup_i2c_dev *qup,
|
|
struct i2c_msg *msg)
|
|
{
|
|
unsigned long left;
|
|
int ret = 0;
|
|
|
|
left = wait_for_completion_timeout(&qup->xfer, HZ);
|
|
if (!left) {
|
|
writel(1, qup->base + QUP_SW_RESET);
|
|
ret = -ETIMEDOUT;
|
|
}
|
|
|
|
if (qup->bus_err || qup->qup_err)
|
|
ret = (qup->bus_err & QUP_I2C_NACK_FLAG) ? -ENXIO : -EIO;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_write_one_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
int ret = 0;
|
|
|
|
qup->msg = msg;
|
|
qup->pos = 0;
|
|
enable_irq(qup->irq);
|
|
qup_i2c_set_blk_data(qup, msg);
|
|
qup_i2c_set_write_mode_v2(qup, msg);
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
|
|
|
do {
|
|
ret = qup_i2c_issue_xfer_v2(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_wait_for_complete(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
qup->blk.pos++;
|
|
} while (qup->blk.pos < qup->blk.count);
|
|
|
|
ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, RESET_BIT, ONE_BYTE);
|
|
|
|
err:
|
|
disable_irq(qup->irq);
|
|
qup->msg = NULL;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_write_one(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
int ret;
|
|
|
|
qup->msg = msg;
|
|
qup->pos = 0;
|
|
|
|
enable_irq(qup->irq);
|
|
|
|
qup_i2c_set_write_mode(qup, msg);
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
|
|
|
do {
|
|
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_issue_write(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_wait_for_complete(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
} while (qup->pos < msg->len);
|
|
|
|
/* Wait for the outstanding data in the fifo to drain */
|
|
ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, RESET_BIT, ONE_BYTE);
|
|
err:
|
|
disable_irq(qup->irq);
|
|
qup->msg = NULL;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void qup_i2c_set_read_mode(struct qup_i2c_dev *qup, int len)
|
|
{
|
|
if (len < qup->in_fifo_sz) {
|
|
/* FIFO mode */
|
|
writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
|
|
writel(len, qup->base + QUP_MX_READ_CNT);
|
|
} else {
|
|
/* BLOCK mode (transfer data on chunks) */
|
|
writel(QUP_INPUT_BLK_MODE | QUP_REPACK_EN,
|
|
qup->base + QUP_IO_MODE);
|
|
writel(len, qup->base + QUP_MX_INPUT_CNT);
|
|
}
|
|
}
|
|
|
|
static void qup_i2c_set_read_mode_v2(struct qup_i2c_dev *qup, int len)
|
|
{
|
|
int tx_len = qup->blk.tx_tag_len;
|
|
|
|
len += qup->blk.rx_tag_len;
|
|
len |= qup->config_run;
|
|
tx_len |= qup->config_run;
|
|
|
|
if (len < qup->in_fifo_sz) {
|
|
/* FIFO mode */
|
|
writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
|
|
writel(tx_len, qup->base + QUP_MX_WRITE_CNT);
|
|
writel(len, qup->base + QUP_MX_READ_CNT);
|
|
} else {
|
|
/* BLOCK mode (transfer data on chunks) */
|
|
writel(QUP_INPUT_BLK_MODE | QUP_REPACK_EN,
|
|
qup->base + QUP_IO_MODE);
|
|
writel(tx_len, qup->base + QUP_MX_OUTPUT_CNT);
|
|
writel(len, qup->base + QUP_MX_INPUT_CNT);
|
|
}
|
|
}
|
|
|
|
static void qup_i2c_issue_read(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
u32 addr, len, val;
|
|
|
|
addr = i2c_8bit_addr_from_msg(msg);
|
|
|
|
/* 0 is used to specify a length 256 (QUP_READ_LIMIT) */
|
|
len = (msg->len == QUP_READ_LIMIT) ? 0 : msg->len;
|
|
|
|
val = ((QUP_TAG_REC | len) << QUP_MSW_SHIFT) | QUP_TAG_START | addr;
|
|
writel(val, qup->base + QUP_OUT_FIFO_BASE);
|
|
}
|
|
|
|
|
|
static int qup_i2c_read_fifo(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
u32 val = 0;
|
|
int idx;
|
|
int ret = 0;
|
|
|
|
for (idx = 0; qup->pos < msg->len; idx++) {
|
|
if ((idx & 1) == 0) {
|
|
/* Check that FIFO have data */
|
|
ret = qup_i2c_wait_ready(qup, QUP_IN_NOT_EMPTY,
|
|
SET_BIT, 4 * ONE_BYTE);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Reading 2 words at time */
|
|
val = readl(qup->base + QUP_IN_FIFO_BASE);
|
|
|
|
msg->buf[qup->pos++] = val & 0xFF;
|
|
} else {
|
|
msg->buf[qup->pos++] = val >> QUP_MSW_SHIFT;
|
|
}
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_read_fifo_v2(struct qup_i2c_dev *qup,
|
|
struct i2c_msg *msg)
|
|
{
|
|
u32 val;
|
|
int idx, pos = 0, ret = 0, total, msg_offset = 0;
|
|
|
|
/*
|
|
* If the message length is already read in
|
|
* the first byte of the buffer, account for
|
|
* that by setting the offset
|
|
*/
|
|
if (qup_i2c_check_msg_len(msg) && (msg->len > 1))
|
|
msg_offset = 1;
|
|
total = qup_i2c_get_data_len(qup);
|
|
total -= msg_offset;
|
|
|
|
/* 2 extra bytes for read tags */
|
|
while (pos < (total + 2)) {
|
|
/* Check that FIFO have data */
|
|
ret = qup_i2c_wait_ready(qup, QUP_IN_NOT_EMPTY,
|
|
SET_BIT, 4 * ONE_BYTE);
|
|
if (ret) {
|
|
dev_err(qup->dev, "timeout for fifo not empty");
|
|
return ret;
|
|
}
|
|
val = readl(qup->base + QUP_IN_FIFO_BASE);
|
|
|
|
for (idx = 0; idx < 4; idx++, val >>= 8, pos++) {
|
|
/* first 2 bytes are tag bytes */
|
|
if (pos < 2)
|
|
continue;
|
|
|
|
if (pos >= (total + 2))
|
|
goto out;
|
|
msg->buf[qup->pos + msg_offset] = val & 0xff;
|
|
qup->pos++;
|
|
}
|
|
}
|
|
|
|
out:
|
|
qup->blk.data_len -= total;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_read_one_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
int ret = 0;
|
|
|
|
qup->msg = msg;
|
|
qup->pos = 0;
|
|
enable_irq(qup->irq);
|
|
qup_i2c_set_blk_data(qup, msg);
|
|
qup_i2c_set_read_mode_v2(qup, msg->len);
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
|
|
|
do {
|
|
ret = qup_i2c_issue_xfer_v2(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_wait_for_complete(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_read_fifo_v2(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
qup->blk.pos++;
|
|
|
|
/* Handle SMBus block read length */
|
|
if (qup_i2c_check_msg_len(msg) && (msg->len == 1)) {
|
|
if (msg->buf[0] > I2C_SMBUS_BLOCK_MAX) {
|
|
ret = -EPROTO;
|
|
goto err;
|
|
}
|
|
msg->len += msg->buf[0];
|
|
qup->pos = 0;
|
|
qup_i2c_set_blk_data(qup, msg);
|
|
/* set tag length for block read */
|
|
qup->blk.tx_tag_len = 2;
|
|
qup_i2c_set_read_mode_v2(qup, msg->buf[0]);
|
|
}
|
|
} while (qup->blk.pos < qup->blk.count);
|
|
|
|
err:
|
|
disable_irq(qup->irq);
|
|
qup->msg = NULL;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_read_one(struct qup_i2c_dev *qup, struct i2c_msg *msg)
|
|
{
|
|
int ret;
|
|
|
|
qup->msg = msg;
|
|
qup->pos = 0;
|
|
|
|
enable_irq(qup->irq);
|
|
qup_i2c_set_read_mode(qup, msg->len);
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
qup_i2c_issue_read(qup, msg);
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
|
|
if (ret)
|
|
goto err;
|
|
|
|
do {
|
|
ret = qup_i2c_wait_for_complete(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
|
|
ret = qup_i2c_read_fifo(qup, msg);
|
|
if (ret)
|
|
goto err;
|
|
} while (qup->pos < msg->len);
|
|
|
|
err:
|
|
disable_irq(qup->irq);
|
|
qup->msg = NULL;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_xfer(struct i2c_adapter *adap,
|
|
struct i2c_msg msgs[],
|
|
int num)
|
|
{
|
|
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
|
|
int ret, idx;
|
|
|
|
ret = pm_runtime_get_sync(qup->dev);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
qup->bus_err = 0;
|
|
qup->qup_err = 0;
|
|
|
|
writel(1, qup->base + QUP_SW_RESET);
|
|
ret = qup_i2c_poll_state(qup, QUP_RESET_STATE);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Configure QUP as I2C mini core */
|
|
writel(I2C_MINI_CORE | I2C_N_VAL, qup->base + QUP_CONFIG);
|
|
|
|
for (idx = 0; idx < num; idx++) {
|
|
if (msgs[idx].len == 0) {
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
if (qup_i2c_poll_state_i2c_master(qup)) {
|
|
ret = -EIO;
|
|
goto out;
|
|
}
|
|
|
|
if (qup_i2c_check_msg_len(&msgs[idx])) {
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
if (msgs[idx].flags & I2C_M_RD)
|
|
ret = qup_i2c_read_one(qup, &msgs[idx]);
|
|
else
|
|
ret = qup_i2c_write_one(qup, &msgs[idx]);
|
|
|
|
if (ret)
|
|
break;
|
|
|
|
ret = qup_i2c_change_state(qup, QUP_RESET_STATE);
|
|
if (ret)
|
|
break;
|
|
}
|
|
|
|
if (ret == 0)
|
|
ret = num;
|
|
out:
|
|
|
|
pm_runtime_mark_last_busy(qup->dev);
|
|
pm_runtime_put_autosuspend(qup->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_xfer_v2(struct i2c_adapter *adap,
|
|
struct i2c_msg msgs[],
|
|
int num)
|
|
{
|
|
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
|
|
int ret, len, idx = 0, use_dma = 0;
|
|
|
|
qup->bus_err = 0;
|
|
qup->qup_err = 0;
|
|
|
|
ret = pm_runtime_get_sync(qup->dev);
|
|
if (ret < 0)
|
|
goto out;
|
|
|
|
writel(1, qup->base + QUP_SW_RESET);
|
|
ret = qup_i2c_poll_state(qup, QUP_RESET_STATE);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Configure QUP as I2C mini core */
|
|
writel(I2C_MINI_CORE | I2C_N_VAL_V2, qup->base + QUP_CONFIG);
|
|
writel(QUP_V2_TAGS_EN, qup->base + QUP_I2C_MASTER_GEN);
|
|
|
|
if ((qup->is_dma)) {
|
|
/* All i2c_msgs should be transferred using either dma or cpu */
|
|
for (idx = 0; idx < num; idx++) {
|
|
if (msgs[idx].len == 0) {
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
len = (msgs[idx].len > qup->out_fifo_sz) ||
|
|
(msgs[idx].len > qup->in_fifo_sz);
|
|
|
|
if ((!is_vmalloc_addr(msgs[idx].buf)) && len) {
|
|
use_dma = 1;
|
|
} else {
|
|
use_dma = 0;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
idx = 0;
|
|
|
|
do {
|
|
if (msgs[idx].len == 0) {
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
if (qup_i2c_poll_state_i2c_master(qup)) {
|
|
ret = -EIO;
|
|
goto out;
|
|
}
|
|
|
|
qup->is_last = (idx == (num - 1));
|
|
if (idx)
|
|
qup->config_run = QUP_I2C_MX_CONFIG_DURING_RUN;
|
|
else
|
|
qup->config_run = 0;
|
|
|
|
reinit_completion(&qup->xfer);
|
|
|
|
if (use_dma) {
|
|
ret = qup_i2c_bam_xfer(adap, &msgs[idx], num);
|
|
} else {
|
|
if (msgs[idx].flags & I2C_M_RD)
|
|
ret = qup_i2c_read_one_v2(qup, &msgs[idx]);
|
|
else
|
|
ret = qup_i2c_write_one_v2(qup, &msgs[idx]);
|
|
}
|
|
} while ((idx++ < (num - 1)) && !use_dma && !ret);
|
|
|
|
if (!ret)
|
|
ret = qup_i2c_change_state(qup, QUP_RESET_STATE);
|
|
|
|
if (ret == 0)
|
|
ret = num;
|
|
out:
|
|
pm_runtime_mark_last_busy(qup->dev);
|
|
pm_runtime_put_autosuspend(qup->dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static u32 qup_i2c_func(struct i2c_adapter *adap)
|
|
{
|
|
return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
|
|
}
|
|
|
|
static const struct i2c_algorithm qup_i2c_algo = {
|
|
.master_xfer = qup_i2c_xfer,
|
|
.functionality = qup_i2c_func,
|
|
};
|
|
|
|
static const struct i2c_algorithm qup_i2c_algo_v2 = {
|
|
.master_xfer = qup_i2c_xfer_v2,
|
|
.functionality = qup_i2c_func,
|
|
};
|
|
|
|
/*
|
|
* The QUP block will issue a NACK and STOP on the bus when reaching
|
|
* the end of the read, the length of the read is specified as one byte
|
|
* which limits the possible read to 256 (QUP_READ_LIMIT) bytes.
|
|
*/
|
|
static struct i2c_adapter_quirks qup_i2c_quirks = {
|
|
.max_read_len = QUP_READ_LIMIT,
|
|
};
|
|
|
|
static void qup_i2c_enable_clocks(struct qup_i2c_dev *qup)
|
|
{
|
|
clk_prepare_enable(qup->clk);
|
|
clk_prepare_enable(qup->pclk);
|
|
}
|
|
|
|
static void qup_i2c_disable_clocks(struct qup_i2c_dev *qup)
|
|
{
|
|
u32 config;
|
|
|
|
qup_i2c_change_state(qup, QUP_RESET_STATE);
|
|
clk_disable_unprepare(qup->clk);
|
|
config = readl(qup->base + QUP_CONFIG);
|
|
config |= QUP_CLOCK_AUTO_GATE;
|
|
writel(config, qup->base + QUP_CONFIG);
|
|
clk_disable_unprepare(qup->pclk);
|
|
}
|
|
|
|
static int qup_i2c_probe(struct platform_device *pdev)
|
|
{
|
|
static const int blk_sizes[] = {4, 16, 32};
|
|
struct qup_i2c_dev *qup;
|
|
unsigned long one_bit_t;
|
|
struct resource *res;
|
|
u32 io_mode, hw_ver, size;
|
|
int ret, fs_div, hs_div;
|
|
u32 src_clk_freq = DEFAULT_SRC_CLK;
|
|
u32 clk_freq = DEFAULT_CLK_FREQ;
|
|
int blocks;
|
|
|
|
qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL);
|
|
if (!qup)
|
|
return -ENOMEM;
|
|
|
|
qup->dev = &pdev->dev;
|
|
init_completion(&qup->xfer);
|
|
platform_set_drvdata(pdev, qup);
|
|
|
|
ret = device_property_read_u32(qup->dev, "clock-frequency", &clk_freq);
|
|
if (ret) {
|
|
dev_notice(qup->dev, "using default clock-frequency %d",
|
|
DEFAULT_CLK_FREQ);
|
|
}
|
|
|
|
if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup-v1.1.1")) {
|
|
qup->adap.algo = &qup_i2c_algo;
|
|
qup->adap.quirks = &qup_i2c_quirks;
|
|
} else {
|
|
qup->adap.algo = &qup_i2c_algo_v2;
|
|
ret = qup_i2c_req_dma(qup);
|
|
|
|
if (ret == -EPROBE_DEFER)
|
|
goto fail_dma;
|
|
else if (ret != 0)
|
|
goto nodma;
|
|
|
|
blocks = (MX_BLOCKS << 1) + 1;
|
|
qup->btx.sg = devm_kzalloc(&pdev->dev,
|
|
sizeof(*qup->btx.sg) * blocks,
|
|
GFP_KERNEL);
|
|
if (!qup->btx.sg) {
|
|
ret = -ENOMEM;
|
|
goto fail_dma;
|
|
}
|
|
sg_init_table(qup->btx.sg, blocks);
|
|
|
|
qup->brx.sg = devm_kzalloc(&pdev->dev,
|
|
sizeof(*qup->brx.sg) * blocks,
|
|
GFP_KERNEL);
|
|
if (!qup->brx.sg) {
|
|
ret = -ENOMEM;
|
|
goto fail_dma;
|
|
}
|
|
sg_init_table(qup->brx.sg, blocks);
|
|
|
|
/* 2 tag bytes for each block + 5 for start, stop tags */
|
|
size = blocks * 2 + 5;
|
|
|
|
qup->start_tag.start = devm_kzalloc(&pdev->dev,
|
|
size, GFP_KERNEL);
|
|
if (!qup->start_tag.start) {
|
|
ret = -ENOMEM;
|
|
goto fail_dma;
|
|
}
|
|
|
|
qup->brx.tag.start = devm_kzalloc(&pdev->dev, 2, GFP_KERNEL);
|
|
if (!qup->brx.tag.start) {
|
|
ret = -ENOMEM;
|
|
goto fail_dma;
|
|
}
|
|
|
|
qup->btx.tag.start = devm_kzalloc(&pdev->dev, 2, GFP_KERNEL);
|
|
if (!qup->btx.tag.start) {
|
|
ret = -ENOMEM;
|
|
goto fail_dma;
|
|
}
|
|
qup->is_dma = true;
|
|
}
|
|
|
|
nodma:
|
|
/* We support frequencies up to FAST Mode (400KHz) */
|
|
if (!clk_freq || clk_freq > 400000) {
|
|
dev_err(qup->dev, "clock frequency not supported %d\n",
|
|
clk_freq);
|
|
return -EINVAL;
|
|
}
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
qup->base = devm_ioremap_resource(qup->dev, res);
|
|
if (IS_ERR(qup->base))
|
|
return PTR_ERR(qup->base);
|
|
|
|
qup->irq = platform_get_irq(pdev, 0);
|
|
if (qup->irq < 0) {
|
|
dev_err(qup->dev, "No IRQ defined\n");
|
|
return qup->irq;
|
|
}
|
|
|
|
if (has_acpi_companion(qup->dev)) {
|
|
ret = device_property_read_u32(qup->dev,
|
|
"src-clock-hz", &src_clk_freq);
|
|
if (ret) {
|
|
dev_notice(qup->dev, "using default src-clock-hz %d",
|
|
DEFAULT_SRC_CLK);
|
|
}
|
|
ACPI_COMPANION_SET(&qup->adap.dev, ACPI_COMPANION(qup->dev));
|
|
} else {
|
|
qup->clk = devm_clk_get(qup->dev, "core");
|
|
if (IS_ERR(qup->clk)) {
|
|
dev_err(qup->dev, "Could not get core clock\n");
|
|
return PTR_ERR(qup->clk);
|
|
}
|
|
|
|
qup->pclk = devm_clk_get(qup->dev, "iface");
|
|
if (IS_ERR(qup->pclk)) {
|
|
dev_err(qup->dev, "Could not get iface clock\n");
|
|
return PTR_ERR(qup->pclk);
|
|
}
|
|
qup_i2c_enable_clocks(qup);
|
|
src_clk_freq = clk_get_rate(qup->clk);
|
|
}
|
|
|
|
/*
|
|
* Bootloaders might leave a pending interrupt on certain QUP's,
|
|
* so we reset the core before registering for interrupts.
|
|
*/
|
|
writel(1, qup->base + QUP_SW_RESET);
|
|
ret = qup_i2c_poll_state_valid(qup);
|
|
if (ret)
|
|
goto fail;
|
|
|
|
ret = devm_request_irq(qup->dev, qup->irq, qup_i2c_interrupt,
|
|
IRQF_TRIGGER_HIGH, "i2c_qup", qup);
|
|
if (ret) {
|
|
dev_err(qup->dev, "Request %d IRQ failed\n", qup->irq);
|
|
goto fail;
|
|
}
|
|
disable_irq(qup->irq);
|
|
|
|
hw_ver = readl(qup->base + QUP_HW_VERSION);
|
|
dev_dbg(qup->dev, "Revision %x\n", hw_ver);
|
|
|
|
io_mode = readl(qup->base + QUP_IO_MODE);
|
|
|
|
/*
|
|
* The block/fifo size w.r.t. 'actual data' is 1/2 due to 'tag'
|
|
* associated with each byte written/received
|
|
*/
|
|
size = QUP_OUTPUT_BLOCK_SIZE(io_mode);
|
|
if (size >= ARRAY_SIZE(blk_sizes)) {
|
|
ret = -EIO;
|
|
goto fail;
|
|
}
|
|
qup->out_blk_sz = blk_sizes[size] / 2;
|
|
|
|
size = QUP_INPUT_BLOCK_SIZE(io_mode);
|
|
if (size >= ARRAY_SIZE(blk_sizes)) {
|
|
ret = -EIO;
|
|
goto fail;
|
|
}
|
|
qup->in_blk_sz = blk_sizes[size] / 2;
|
|
|
|
size = QUP_OUTPUT_FIFO_SIZE(io_mode);
|
|
qup->out_fifo_sz = qup->out_blk_sz * (2 << size);
|
|
|
|
size = QUP_INPUT_FIFO_SIZE(io_mode);
|
|
qup->in_fifo_sz = qup->in_blk_sz * (2 << size);
|
|
|
|
fs_div = ((src_clk_freq / clk_freq) / 2) - 3;
|
|
hs_div = 3;
|
|
qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff);
|
|
|
|
/*
|
|
* Time it takes for a byte to be clocked out on the bus.
|
|
* Each byte takes 9 clock cycles (8 bits + 1 ack).
|
|
*/
|
|
one_bit_t = (USEC_PER_SEC / clk_freq) + 1;
|
|
qup->one_byte_t = one_bit_t * 9;
|
|
|
|
dev_dbg(qup->dev, "IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n",
|
|
qup->in_blk_sz, qup->in_fifo_sz,
|
|
qup->out_blk_sz, qup->out_fifo_sz);
|
|
|
|
i2c_set_adapdata(&qup->adap, qup);
|
|
qup->adap.dev.parent = qup->dev;
|
|
qup->adap.dev.of_node = pdev->dev.of_node;
|
|
qup->is_last = true;
|
|
|
|
strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup->adap.name));
|
|
|
|
pm_runtime_set_autosuspend_delay(qup->dev, MSEC_PER_SEC);
|
|
pm_runtime_use_autosuspend(qup->dev);
|
|
pm_runtime_set_active(qup->dev);
|
|
pm_runtime_enable(qup->dev);
|
|
|
|
ret = i2c_add_adapter(&qup->adap);
|
|
if (ret)
|
|
goto fail_runtime;
|
|
|
|
return 0;
|
|
|
|
fail_runtime:
|
|
pm_runtime_disable(qup->dev);
|
|
pm_runtime_set_suspended(qup->dev);
|
|
fail:
|
|
qup_i2c_disable_clocks(qup);
|
|
fail_dma:
|
|
if (qup->btx.dma)
|
|
dma_release_channel(qup->btx.dma);
|
|
if (qup->brx.dma)
|
|
dma_release_channel(qup->brx.dma);
|
|
return ret;
|
|
}
|
|
|
|
static int qup_i2c_remove(struct platform_device *pdev)
|
|
{
|
|
struct qup_i2c_dev *qup = platform_get_drvdata(pdev);
|
|
|
|
if (qup->is_dma) {
|
|
dma_release_channel(qup->btx.dma);
|
|
dma_release_channel(qup->brx.dma);
|
|
}
|
|
|
|
disable_irq(qup->irq);
|
|
qup_i2c_disable_clocks(qup);
|
|
i2c_del_adapter(&qup->adap);
|
|
pm_runtime_disable(qup->dev);
|
|
pm_runtime_set_suspended(qup->dev);
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int qup_i2c_pm_suspend_runtime(struct device *device)
|
|
{
|
|
struct qup_i2c_dev *qup = dev_get_drvdata(device);
|
|
|
|
dev_dbg(device, "pm_runtime: suspending...\n");
|
|
qup_i2c_disable_clocks(qup);
|
|
return 0;
|
|
}
|
|
|
|
static int qup_i2c_pm_resume_runtime(struct device *device)
|
|
{
|
|
struct qup_i2c_dev *qup = dev_get_drvdata(device);
|
|
|
|
dev_dbg(device, "pm_runtime: resuming...\n");
|
|
qup_i2c_enable_clocks(qup);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int qup_i2c_suspend(struct device *device)
|
|
{
|
|
if (!pm_runtime_suspended(device))
|
|
return qup_i2c_pm_suspend_runtime(device);
|
|
return 0;
|
|
}
|
|
|
|
static int qup_i2c_resume(struct device *device)
|
|
{
|
|
qup_i2c_pm_resume_runtime(device);
|
|
pm_runtime_mark_last_busy(device);
|
|
pm_request_autosuspend(device);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct dev_pm_ops qup_i2c_qup_pm_ops = {
|
|
SET_SYSTEM_SLEEP_PM_OPS(
|
|
qup_i2c_suspend,
|
|
qup_i2c_resume)
|
|
SET_RUNTIME_PM_OPS(
|
|
qup_i2c_pm_suspend_runtime,
|
|
qup_i2c_pm_resume_runtime,
|
|
NULL)
|
|
};
|
|
|
|
static const struct of_device_id qup_i2c_dt_match[] = {
|
|
{ .compatible = "qcom,i2c-qup-v1.1.1" },
|
|
{ .compatible = "qcom,i2c-qup-v2.1.1" },
|
|
{ .compatible = "qcom,i2c-qup-v2.2.1" },
|
|
{}
|
|
};
|
|
MODULE_DEVICE_TABLE(of, qup_i2c_dt_match);
|
|
|
|
#if IS_ENABLED(CONFIG_ACPI)
|
|
static const struct acpi_device_id qup_i2c_acpi_match[] = {
|
|
{ "QCOM8010"},
|
|
{ },
|
|
};
|
|
MODULE_DEVICE_TABLE(acpi, qup_i2c_acpi_match);
|
|
#endif
|
|
|
|
static struct platform_driver qup_i2c_driver = {
|
|
.probe = qup_i2c_probe,
|
|
.remove = qup_i2c_remove,
|
|
.driver = {
|
|
.name = "i2c_qup",
|
|
.pm = &qup_i2c_qup_pm_ops,
|
|
.of_match_table = qup_i2c_dt_match,
|
|
.acpi_match_table = ACPI_PTR(qup_i2c_acpi_match),
|
|
},
|
|
};
|
|
|
|
module_platform_driver(qup_i2c_driver);
|
|
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_ALIAS("platform:i2c_qup");
|