79 lines
2.0 KiB
C
79 lines
2.0 KiB
C
/*
|
|
* Copyright (C) 2008-2012 ST-Ericsson
|
|
*
|
|
* Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2, as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
*/
|
|
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/io.h>
|
|
#include <linux/platform_data/db8500_thermal.h>
|
|
#include <linux/amba/bus.h>
|
|
#include <linux/amba/pl022.h>
|
|
#include <linux/mfd/abx500/ab8500.h>
|
|
#include <linux/regulator/ab8500.h>
|
|
#include <linux/regulator/fixed.h>
|
|
#include <linux/regulator/driver.h>
|
|
#include <linux/mfd/tps6105x.h>
|
|
#include <linux/platform_data/leds-lp55xx.h>
|
|
#include <linux/input.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/leds.h>
|
|
#include <linux/pinctrl/consumer.h>
|
|
#include <linux/platform_data/pinctrl-nomadik.h>
|
|
#include <linux/platform_data/dma-ste-dma40.h>
|
|
|
|
#include <asm/mach-types.h>
|
|
|
|
#include "setup.h"
|
|
#include "devices.h"
|
|
#include "irqs.h"
|
|
|
|
#include "ste-dma40-db8500.h"
|
|
#include "db8500-regs.h"
|
|
#include "devices-db8500.h"
|
|
#include "board-mop500.h"
|
|
#include "board-mop500-regulators.h"
|
|
|
|
struct ab8500_platform_data ab8500_platdata = {
|
|
.irq_base = MOP500_AB8500_IRQ_BASE,
|
|
.regulator = &ab8500_regulator_plat_data,
|
|
};
|
|
|
|
#ifdef CONFIG_STE_DMA40
|
|
static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
|
|
.mode = STEDMA40_MODE_LOGICAL,
|
|
.dir = DMA_DEV_TO_MEM,
|
|
.dev_type = DB8500_DMA_DEV8_SSP0,
|
|
};
|
|
|
|
static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
|
|
.mode = STEDMA40_MODE_LOGICAL,
|
|
.dir = DMA_MEM_TO_DEV,
|
|
.dev_type = DB8500_DMA_DEV8_SSP0,
|
|
};
|
|
#endif
|
|
|
|
struct pl022_ssp_controller ssp0_plat = {
|
|
.bus_id = 0,
|
|
#ifdef CONFIG_STE_DMA40
|
|
.enable_dma = 1,
|
|
.dma_filter = stedma40_filter,
|
|
.dma_rx_param = &ssp0_dma_cfg_rx,
|
|
.dma_tx_param = &ssp0_dma_cfg_tx,
|
|
#else
|
|
.enable_dma = 0,
|
|
#endif
|
|
/* on this platform, gpio 31,142,144,214 &
|
|
* 224 are connected as chip selects
|
|
*/
|
|
.num_chipselect = 5,
|
|
};
|