464 lines
20 KiB
C
464 lines
20 KiB
C
/******************************************************************************
|
|
*
|
|
* This file is provided under a dual BSD/GPLv2 license. When using or
|
|
* redistributing this file, you may do so under either license.
|
|
*
|
|
* GPL LICENSE SUMMARY
|
|
*
|
|
* Copyright(c) 2005 - 2012 Intel Corporation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of version 2 of the GNU General Public License as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
* General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
|
|
* USA
|
|
*
|
|
* The full GNU General Public License is included in this distribution
|
|
* in the file called LICENSE.GPL.
|
|
*
|
|
* Contact Information:
|
|
* Intel Linux Wireless <ilw@linux.intel.com>
|
|
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
|
|
*
|
|
* BSD LICENSE
|
|
*
|
|
* Copyright(c) 2005 - 2012 Intel Corporation. All rights reserved.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* * Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* * Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* * Neither the name Intel Corporation nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
*****************************************************************************/
|
|
#ifndef __iwl_csr_h__
|
|
#define __iwl_csr_h__
|
|
/*
|
|
* CSR (control and status registers)
|
|
*
|
|
* CSR registers are mapped directly into PCI bus space, and are accessible
|
|
* whenever platform supplies power to device, even when device is in
|
|
* low power states due to driver-invoked device resets
|
|
* (e.g. CSR_RESET_REG_FLAG_SW_RESET) or uCode-driven power-saving modes.
|
|
*
|
|
* Use iwl_write32() and iwl_read32() family to access these registers;
|
|
* these provide simple PCI bus access, without waking up the MAC.
|
|
* Do not use iwl_write_direct32() family for these registers;
|
|
* no need to "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ.
|
|
* The MAC (uCode processor, etc.) does not need to be powered up for accessing
|
|
* the CSR registers.
|
|
*
|
|
* NOTE: Device does need to be awake in order to read this memory
|
|
* via CSR_EEPROM and CSR_OTP registers
|
|
*/
|
|
#define CSR_BASE (0x000)
|
|
|
|
#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
|
|
#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
|
|
#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
|
|
#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
|
|
#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
|
|
#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
|
|
#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
|
|
#define CSR_GP_CNTRL (CSR_BASE+0x024)
|
|
|
|
/* 2nd byte of CSR_INT_COALESCING, not accessible via iwl_write32()! */
|
|
#define CSR_INT_PERIODIC_REG (CSR_BASE+0x005)
|
|
|
|
/*
|
|
* Hardware revision info
|
|
* Bit fields:
|
|
* 31-8: Reserved
|
|
* 7-4: Type of device: see CSR_HW_REV_TYPE_xxx definitions
|
|
* 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
|
|
* 1-0: "Dash" (-) value, as in A-1, etc.
|
|
*
|
|
* NOTE: Revision step affects calculation of CCK txpower for 4965.
|
|
* NOTE: See also CSR_HW_REV_WA_REG (work-around for bug in 4965).
|
|
*/
|
|
#define CSR_HW_REV (CSR_BASE+0x028)
|
|
|
|
/*
|
|
* EEPROM and OTP (one-time-programmable) memory reads
|
|
*
|
|
* NOTE: Device must be awake, initialized via apm_ops.init(),
|
|
* in order to read.
|
|
*/
|
|
#define CSR_EEPROM_REG (CSR_BASE+0x02c)
|
|
#define CSR_EEPROM_GP (CSR_BASE+0x030)
|
|
#define CSR_OTP_GP_REG (CSR_BASE+0x034)
|
|
|
|
#define CSR_GIO_REG (CSR_BASE+0x03C)
|
|
#define CSR_GP_UCODE_REG (CSR_BASE+0x048)
|
|
#define CSR_GP_DRIVER_REG (CSR_BASE+0x050)
|
|
|
|
/*
|
|
* UCODE-DRIVER GP (general purpose) mailbox registers.
|
|
* SET/CLR registers set/clear bit(s) if "1" is written.
|
|
*/
|
|
#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
|
|
#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
|
|
#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
|
|
#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
|
|
|
|
#define CSR_LED_REG (CSR_BASE+0x094)
|
|
#define CSR_DRAM_INT_TBL_REG (CSR_BASE+0x0A0)
|
|
#define CSR_MAC_SHADOW_REG_CTRL (CSR_BASE+0x0A8) /* 6000 and up */
|
|
|
|
|
|
/* GIO Chicken Bits (PCI Express bus link power management) */
|
|
#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
|
|
|
|
/* Analog phase-lock-loop configuration */
|
|
#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
|
|
|
|
/*
|
|
* CSR Hardware Revision Workaround Register. Indicates hardware rev;
|
|
* "step" determines CCK backoff for txpower calculation. Used for 4965 only.
|
|
* See also CSR_HW_REV register.
|
|
* Bit fields:
|
|
* 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
|
|
* 1-0: "Dash" (-) value, as in C-1, etc.
|
|
*/
|
|
#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
|
|
|
|
#define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240)
|
|
#define CSR_DBG_LINK_PWR_MGMT_REG (CSR_BASE+0x250)
|
|
|
|
/* Bits for CSR_HW_IF_CONFIG_REG */
|
|
#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
|
|
#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
|
|
#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
|
|
|
|
#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000)
|
|
#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
|
|
#define CSR_HW_IF_CONFIG_REG_BIT_NIC_READY (0x00400000) /* PCI_OWN_SEM */
|
|
#define CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE (0x02000000) /* ME_OWN */
|
|
#define CSR_HW_IF_CONFIG_REG_PREPARE (0x08000000) /* WAKE_ME */
|
|
|
|
#define CSR_INT_PERIODIC_DIS (0x00) /* disable periodic int*/
|
|
#define CSR_INT_PERIODIC_ENA (0xFF) /* 255*32 usec ~ 8 msec*/
|
|
|
|
/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
|
|
* acknowledged (reset) by host writing "1" to flagged bits. */
|
|
#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */
|
|
#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */
|
|
#define CSR_INT_BIT_RX_PERIODIC (1 << 28) /* Rx periodic */
|
|
#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */
|
|
#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */
|
|
#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */
|
|
#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */
|
|
#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */
|
|
#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses */
|
|
#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */
|
|
#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */
|
|
|
|
#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
|
|
CSR_INT_BIT_HW_ERR | \
|
|
CSR_INT_BIT_FH_TX | \
|
|
CSR_INT_BIT_SW_ERR | \
|
|
CSR_INT_BIT_RF_KILL | \
|
|
CSR_INT_BIT_SW_RX | \
|
|
CSR_INT_BIT_WAKEUP | \
|
|
CSR_INT_BIT_ALIVE)
|
|
|
|
/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
|
|
#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */
|
|
#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */
|
|
#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */
|
|
#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */
|
|
#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */
|
|
#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */
|
|
|
|
#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
|
|
CSR_FH_INT_BIT_RX_CHNL1 | \
|
|
CSR_FH_INT_BIT_RX_CHNL0)
|
|
|
|
#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
|
|
CSR_FH_INT_BIT_TX_CHNL0)
|
|
|
|
/* GPIO */
|
|
#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
|
|
#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
|
|
#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC (0x00000200)
|
|
|
|
/* RESET */
|
|
#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
|
|
#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
|
|
#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
|
|
#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
|
|
#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
|
|
#define CSR_RESET_LINK_PWR_MGMT_DISABLED (0x80000000)
|
|
|
|
/*
|
|
* GP (general purpose) CONTROL REGISTER
|
|
* Bit fields:
|
|
* 27: HW_RF_KILL_SW
|
|
* Indicates state of (platform's) hardware RF-Kill switch
|
|
* 26-24: POWER_SAVE_TYPE
|
|
* Indicates current power-saving mode:
|
|
* 000 -- No power saving
|
|
* 001 -- MAC power-down
|
|
* 010 -- PHY (radio) power-down
|
|
* 011 -- Error
|
|
* 9-6: SYS_CONFIG
|
|
* Indicates current system configuration, reflecting pins on chip
|
|
* as forced high/low by device circuit board.
|
|
* 4: GOING_TO_SLEEP
|
|
* Indicates MAC is entering a power-saving sleep power-down.
|
|
* Not a good time to access device-internal resources.
|
|
* 3: MAC_ACCESS_REQ
|
|
* Host sets this to request and maintain MAC wakeup, to allow host
|
|
* access to device-internal resources. Host must wait for
|
|
* MAC_CLOCK_READY (and !GOING_TO_SLEEP) before accessing non-CSR
|
|
* device registers.
|
|
* 2: INIT_DONE
|
|
* Host sets this to put device into fully operational D0 power mode.
|
|
* Host resets this after SW_RESET to put device into low power mode.
|
|
* 0: MAC_CLOCK_READY
|
|
* Indicates MAC (ucode processor, etc.) is powered up and can run.
|
|
* Internal resources are accessible.
|
|
* NOTE: This does not indicate that the processor is actually running.
|
|
* NOTE: This does not indicate that device has completed
|
|
* init or post-power-down restore of internal SRAM memory.
|
|
* Use CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP as indication that
|
|
* SRAM is restored and uCode is in normal operation mode.
|
|
* Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and
|
|
* do not need to save/restore it.
|
|
* NOTE: After device reset, this bit remains "0" until host sets
|
|
* INIT_DONE
|
|
*/
|
|
#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
|
|
#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
|
|
#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
|
|
#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
|
|
|
|
#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
|
|
|
|
#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
|
|
#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
|
|
#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
|
|
|
|
|
|
/* HW REV */
|
|
#define CSR_HW_REV_TYPE_MSK (0x00001F0)
|
|
#define CSR_HW_REV_TYPE_5300 (0x0000020)
|
|
#define CSR_HW_REV_TYPE_5350 (0x0000030)
|
|
#define CSR_HW_REV_TYPE_5100 (0x0000050)
|
|
#define CSR_HW_REV_TYPE_5150 (0x0000040)
|
|
#define CSR_HW_REV_TYPE_1000 (0x0000060)
|
|
#define CSR_HW_REV_TYPE_6x00 (0x0000070)
|
|
#define CSR_HW_REV_TYPE_6x50 (0x0000080)
|
|
#define CSR_HW_REV_TYPE_6150 (0x0000084)
|
|
#define CSR_HW_REV_TYPE_6x05 (0x00000B0)
|
|
#define CSR_HW_REV_TYPE_6x30 CSR_HW_REV_TYPE_6x05
|
|
#define CSR_HW_REV_TYPE_6x35 CSR_HW_REV_TYPE_6x05
|
|
#define CSR_HW_REV_TYPE_2x30 (0x00000C0)
|
|
#define CSR_HW_REV_TYPE_2x00 (0x0000100)
|
|
#define CSR_HW_REV_TYPE_105 (0x0000110)
|
|
#define CSR_HW_REV_TYPE_135 (0x0000120)
|
|
#define CSR_HW_REV_TYPE_NONE (0x00001F0)
|
|
|
|
/* EEPROM REG */
|
|
#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
|
|
#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
|
|
#define CSR_EEPROM_REG_MSK_ADDR (0x0000FFFC)
|
|
#define CSR_EEPROM_REG_MSK_DATA (0xFFFF0000)
|
|
|
|
/* EEPROM GP */
|
|
#define CSR_EEPROM_GP_VALID_MSK (0x00000007) /* signature */
|
|
#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
|
|
#define CSR_EEPROM_GP_BAD_SIGNATURE_BOTH_EEP_AND_OTP (0x00000000)
|
|
#define CSR_EEPROM_GP_BAD_SIG_EEP_GOOD_SIG_OTP (0x00000001)
|
|
#define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002)
|
|
#define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004)
|
|
|
|
/* One-time-programmable memory general purpose reg */
|
|
#define CSR_OTP_GP_REG_DEVICE_SELECT (0x00010000) /* 0 - EEPROM, 1 - OTP */
|
|
#define CSR_OTP_GP_REG_OTP_ACCESS_MODE (0x00020000) /* 0 - absolute, 1 - relative */
|
|
#define CSR_OTP_GP_REG_ECC_CORR_STATUS_MSK (0x00100000) /* bit 20 */
|
|
#define CSR_OTP_GP_REG_ECC_UNCORR_STATUS_MSK (0x00200000) /* bit 21 */
|
|
|
|
/* GP REG */
|
|
#define CSR_GP_REG_POWER_SAVE_STATUS_MSK (0x03000000) /* bit 24/25 */
|
|
#define CSR_GP_REG_NO_POWER_SAVE (0x00000000)
|
|
#define CSR_GP_REG_MAC_POWER_SAVE (0x01000000)
|
|
#define CSR_GP_REG_PHY_POWER_SAVE (0x02000000)
|
|
#define CSR_GP_REG_POWER_SAVE_ERROR (0x03000000)
|
|
|
|
|
|
/* CSR GIO */
|
|
#define CSR_GIO_REG_VAL_L0S_ENABLED (0x00000002)
|
|
|
|
/*
|
|
* UCODE-DRIVER GP (general purpose) mailbox register 1
|
|
* Host driver and uCode write and/or read this register to communicate with
|
|
* each other.
|
|
* Bit fields:
|
|
* 4: UCODE_DISABLE
|
|
* Host sets this to request permanent halt of uCode, same as
|
|
* sending CARD_STATE command with "halt" bit set.
|
|
* 3: CT_KILL_EXIT
|
|
* Host sets this to request exit from CT_KILL state, i.e. host thinks
|
|
* device temperature is low enough to continue normal operation.
|
|
* 2: CMD_BLOCKED
|
|
* Host sets this during RF KILL power-down sequence (HW, SW, CT KILL)
|
|
* to release uCode to clear all Tx and command queues, enter
|
|
* unassociated mode, and power down.
|
|
* NOTE: Some devices also use HBUS_TARG_MBX_C register for this bit.
|
|
* 1: SW_BIT_RFKILL
|
|
* Host sets this when issuing CARD_STATE command to request
|
|
* device sleep.
|
|
* 0: MAC_SLEEP
|
|
* uCode sets this when preparing a power-saving power-down.
|
|
* uCode resets this when power-up is complete and SRAM is sane.
|
|
* NOTE: device saves internal SRAM data to host when powering down,
|
|
* and must restore this data after powering back up.
|
|
* MAC_SLEEP is the best indication that restore is complete.
|
|
* Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and
|
|
* do not need to save/restore it.
|
|
*/
|
|
#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
|
|
#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
|
|
#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
|
|
#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
|
|
#define CSR_UCODE_DRV_GP1_BIT_D3_CFG_COMPLETE (0x00000020)
|
|
|
|
/* GP Driver */
|
|
#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_MSK (0x00000003)
|
|
#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_3x3_HYB (0x00000000)
|
|
#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_HYB (0x00000001)
|
|
#define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_IPA (0x00000002)
|
|
#define CSR_GP_DRIVER_REG_BIT_CALIB_VERSION6 (0x00000004)
|
|
#define CSR_GP_DRIVER_REG_BIT_6050_1x2 (0x00000008)
|
|
|
|
#define CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER (0x00000080)
|
|
|
|
/* GIO Chicken Bits (PCI Express bus link power management) */
|
|
#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
|
|
#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
|
|
|
|
/* LED */
|
|
#define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF)
|
|
#define CSR_LED_REG_TRUN_ON (0x78)
|
|
#define CSR_LED_REG_TRUN_OFF (0x38)
|
|
|
|
/* ANA_PLL */
|
|
#define CSR50_ANA_PLL_CFG_VAL (0x00880300)
|
|
|
|
/* HPET MEM debug */
|
|
#define CSR_DBG_HPET_MEM_REG_VAL (0xFFFF0000)
|
|
|
|
/* DRAM INT TABLE */
|
|
#define CSR_DRAM_INT_TBL_ENABLE (1 << 31)
|
|
#define CSR_DRAM_INIT_TBL_WRAP_CHECK (1 << 27)
|
|
|
|
/*
|
|
* HBUS (Host-side Bus)
|
|
*
|
|
* HBUS registers are mapped directly into PCI bus space, but are used
|
|
* to indirectly access device's internal memory or registers that
|
|
* may be powered-down.
|
|
*
|
|
* Use iwl_write_direct32()/iwl_read_direct32() family for these registers;
|
|
* host must "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ
|
|
* to make sure the MAC (uCode processor, etc.) is powered up for accessing
|
|
* internal resources.
|
|
*
|
|
* Do not use iwl_write32()/iwl_read32() family to access these registers;
|
|
* these provide only simple PCI bus access, without waking up the MAC.
|
|
*/
|
|
#define HBUS_BASE (0x400)
|
|
|
|
/*
|
|
* Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
|
|
* structures, error log, event log, verifying uCode load).
|
|
* First write to address register, then read from or write to data register
|
|
* to complete the job. Once the address register is set up, accesses to
|
|
* data registers auto-increment the address by one dword.
|
|
* Bit usage for address registers (read or write):
|
|
* 0-31: memory address within device
|
|
*/
|
|
#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
|
|
#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
|
|
#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
|
|
#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
|
|
|
|
/* Mailbox C, used as workaround alternative to CSR_UCODE_DRV_GP1 mailbox */
|
|
#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
|
|
#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
|
|
|
|
/*
|
|
* Registers for accessing device's internal peripheral registers
|
|
* (e.g. SCD, BSM, etc.). First write to address register,
|
|
* then read from or write to data register to complete the job.
|
|
* Bit usage for address registers (read or write):
|
|
* 0-15: register address (offset) within device
|
|
* 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
|
|
*/
|
|
#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
|
|
#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
|
|
#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
|
|
#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
|
|
|
|
/* Used to enable DBGM */
|
|
#define HBUS_TARG_TEST_REG (HBUS_BASE+0x05c)
|
|
|
|
/*
|
|
* Per-Tx-queue write pointer (index, really!)
|
|
* Indicates index to next TFD that driver will fill (1 past latest filled).
|
|
* Bit usage:
|
|
* 0-7: queue write index
|
|
* 11-8: queue selector
|
|
*/
|
|
#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
|
|
|
|
/**********************************************************
|
|
* CSR values
|
|
**********************************************************/
|
|
/*
|
|
* host interrupt timeout value
|
|
* used with setting interrupt coalescing timer
|
|
* the CSR_INT_COALESCING is an 8 bit register in 32-usec unit
|
|
*
|
|
* default interrupt coalescing timer is 64 x 32 = 2048 usecs
|
|
* default interrupt coalescing calibration timer is 16 x 32 = 512 usecs
|
|
*/
|
|
#define IWL_HOST_INT_TIMEOUT_MAX (0xFF)
|
|
#define IWL_HOST_INT_TIMEOUT_DEF (0x40)
|
|
#define IWL_HOST_INT_TIMEOUT_MIN (0x0)
|
|
#define IWL_HOST_INT_CALIB_TIMEOUT_MAX (0xFF)
|
|
#define IWL_HOST_INT_CALIB_TIMEOUT_DEF (0x10)
|
|
#define IWL_HOST_INT_CALIB_TIMEOUT_MIN (0x0)
|
|
|
|
#endif /* !__iwl_csr_h__ */
|