OpenCloudOS-Kernel/arch/arc/mm/cache_arc700.c

769 lines
23 KiB
C

/*
* ARC700 VIPT Cache Management
*
* Copyright (C) 2004, 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* vineetg: May 2011: for Non-aliasing VIPT D-cache following can be NOPs
* -flush_cache_dup_mm (fork)
* -likewise for flush_cache_mm (exit/execve)
* -likewise for flush_cache_range,flush_cache_page (munmap, exit, COW-break)
*
* vineetg: Apr 2011
* -Now that MMU can support larger pg sz (16K), the determiniation of
* aliasing shd not be based on assumption of 8k pg
*
* vineetg: Mar 2011
* -optimised version of flush_icache_range( ) for making I/D coherent
* when vaddr is available (agnostic of num of aliases)
*
* vineetg: Mar 2011
* -Added documentation about I-cache aliasing on ARC700 and the way it
* was handled up until MMU V2.
* -Spotted a three year old bug when killing the 4 aliases, which needs
* bottom 2 bits, so we need to do paddr | {0x00, 0x01, 0x02, 0x03}
* instead of paddr | {0x00, 0x01, 0x10, 0x11}
* (Rajesh you owe me one now)
*
* vineetg: Dec 2010
* -Off-by-one error when computing num_of_lines to flush
* This broke signal handling with bionic which uses synthetic sigret stub
*
* vineetg: Mar 2010
* -GCC can't generate ZOL for core cache flush loops.
* Conv them into iterations based as opposed to while (start < end) types
*
* Vineetg: July 2009
* -In I-cache flush routine we used to chk for aliasing for every line INV.
* Instead now we setup routines per cache geometry and invoke them
* via function pointers.
*
* Vineetg: Jan 2009
* -Cache Line flush routines used to flush an extra line beyond end addr
* because check was while (end >= start) instead of (end > start)
* =Some call sites had to work around by doing -1, -4 etc to end param
* =Some callers didnt care. This was spec bad in case of INV routines
* which would discard valid data (cause of the horrible ext2 bug
* in ARC IDE driver)
*
* vineetg: June 11th 2008: Fixed flush_icache_range( )
* -Since ARC700 caches are not coherent (I$ doesnt snoop D$) both need
* to be flushed, which it was not doing.
* -load_module( ) passes vmalloc addr (Kernel Virtual Addr) to the API,
* however ARC cache maintenance OPs require PHY addr. Thus need to do
* vmalloc_to_phy.
* -Also added optimisation there, that for range > PAGE SIZE we flush the
* entire cache in one shot rather than line by line. For e.g. a module
* with Code sz 600k, old code flushed 600k worth of cache (line-by-line),
* while cache is only 16 or 32k.
*/
#include <linux/module.h>
#include <linux/mm.h>
#include <linux/sched.h>
#include <linux/cache.h>
#include <linux/mmu_context.h>
#include <linux/syscalls.h>
#include <linux/uaccess.h>
#include <asm/cacheflush.h>
#include <asm/cachectl.h>
#include <asm/setup.h>
#ifdef CONFIG_ARC_HAS_ICACHE
static void __ic_line_inv_no_alias(unsigned long, int);
static void __ic_line_inv_2_alias(unsigned long, int);
static void __ic_line_inv_4_alias(unsigned long, int);
/* Holds the ptr to flush routine, dependign on size due to aliasing issues */
static void (*___flush_icache_rtn) (unsigned long, int);
#endif
char *arc_cache_mumbojumbo(int cpu_id, char *buf, int len)
{
int n = 0;
unsigned int c = smp_processor_id();
#define PR_CACHE(p, enb, str) \
{ \
if (!(p)->ver) \
n += scnprintf(buf + n, len - n, str"\t\t: N/A\n"); \
else \
n += scnprintf(buf + n, len - n, \
str"\t\t: (%uK) VIPT, %dway set-asc, %ub Line %s\n", \
TO_KB((p)->sz), (p)->assoc, (p)->line_len, \
enb ? "" : "DISABLED (kernel-build)"); \
}
PR_CACHE(&cpuinfo_arc700[c].icache, __CONFIG_ARC_HAS_ICACHE, "I-Cache");
PR_CACHE(&cpuinfo_arc700[c].dcache, __CONFIG_ARC_HAS_DCACHE, "D-Cache");
return buf;
}
/*
* Read the Cache Build Confuration Registers, Decode them and save into
* the cpuinfo structure for later use.
* No Validation done here, simply read/convert the BCRs
*/
void __init read_decode_cache_bcr(void)
{
struct bcr_cache ibcr, dbcr;
struct cpuinfo_arc_cache *p_ic, *p_dc;
unsigned int cpu = smp_processor_id();
p_ic = &cpuinfo_arc700[cpu].icache;
READ_BCR(ARC_REG_IC_BCR, ibcr);
if (ibcr.config == 0x3)
p_ic->assoc = 2;
p_ic->line_len = 8 << ibcr.line_len;
p_ic->sz = 0x200 << ibcr.sz;
p_ic->ver = ibcr.ver;
p_dc = &cpuinfo_arc700[cpu].dcache;
READ_BCR(ARC_REG_DC_BCR, dbcr);
if (dbcr.config == 0x2)
p_dc->assoc = 4;
p_dc->line_len = 16 << dbcr.line_len;
p_dc->sz = 0x200 << dbcr.sz;
p_dc->ver = dbcr.ver;
}
/*
* 1. Validate the Cache Geomtery (compile time config matches hardware)
* 2. If I-cache suffers from aliasing, setup work arounds (difft flush rtn)
* (aliasing D-cache configurations are not supported YET)
* 3. Enable the Caches, setup default flush mode for D-Cache
* 3. Calculate the SHMLBA used by user space
*/
void __init arc_cache_init(void)
{
unsigned int temp;
unsigned int cpu = smp_processor_id();
struct cpuinfo_arc_cache *ic = &cpuinfo_arc700[cpu].icache;
struct cpuinfo_arc_cache *dc = &cpuinfo_arc700[cpu].dcache;
int way_pg_ratio = way_pg_ratio;
char str[256];
printk(arc_cache_mumbojumbo(0, str, sizeof(str)));
if (!ic->ver)
goto chk_dc;
#ifdef CONFIG_ARC_HAS_ICACHE
/* 1. Confirm some of I-cache params which Linux assumes */
if ((ic->assoc != ARC_ICACHE_WAYS) ||
(ic->line_len != ARC_ICACHE_LINE_LEN)) {
panic("Cache H/W doesn't match kernel Config");
}
#if (CONFIG_ARC_MMU_VER > 2)
if (ic->ver != 3) {
if (running_on_hw)
panic("Cache ver doesn't match MMU ver\n");
/* For ISS - suggest the toggles to use */
pr_err("Use -prop=icache_version=3,-prop=dcache_version=3\n");
}
#endif
/*
* if Cache way size is <= page size then no aliasing exhibited
* otherwise ratio determines num of aliases.
* e.g. 32K I$, 2 way set assoc, 8k pg size
* way-sz = 32k/2 = 16k
* way-pg-ratio = 16k/8k = 2, so 2 aliases possible
* (meaning 1 line could be in 2 possible locations).
*/
way_pg_ratio = ic->sz / ARC_ICACHE_WAYS / PAGE_SIZE;
switch (way_pg_ratio) {
case 0:
case 1:
___flush_icache_rtn = __ic_line_inv_no_alias;
break;
case 2:
___flush_icache_rtn = __ic_line_inv_2_alias;
break;
case 4:
___flush_icache_rtn = __ic_line_inv_4_alias;
break;
default:
panic("Unsupported I-Cache Sz\n");
}
#endif
/* Enable/disable I-Cache */
temp = read_aux_reg(ARC_REG_IC_CTRL);
#ifdef CONFIG_ARC_HAS_ICACHE
temp &= ~IC_CTRL_CACHE_DISABLE;
#else
temp |= IC_CTRL_CACHE_DISABLE;
#endif
write_aux_reg(ARC_REG_IC_CTRL, temp);
chk_dc:
if (!dc->ver)
return;
#ifdef CONFIG_ARC_HAS_DCACHE
if ((dc->assoc != ARC_DCACHE_WAYS) ||
(dc->line_len != ARC_DCACHE_LINE_LEN)) {
panic("Cache H/W doesn't match kernel Config");
}
/* check for D-Cache aliasing */
if ((dc->sz / ARC_DCACHE_WAYS) > PAGE_SIZE)
panic("D$ aliasing not handled right now\n");
#endif
/* Set the default Invalidate Mode to "simpy discard dirty lines"
* as this is more frequent then flush before invalidate
* Ofcourse we toggle this default behviour when desired
*/
temp = read_aux_reg(ARC_REG_DC_CTRL);
temp &= ~DC_CTRL_INV_MODE_FLUSH;
#ifdef CONFIG_ARC_HAS_DCACHE
/* Enable D-Cache: Clear Bit 0 */
write_aux_reg(ARC_REG_DC_CTRL, temp & ~IC_CTRL_CACHE_DISABLE);
#else
/* Flush D cache */
write_aux_reg(ARC_REG_DC_FLSH, 0x1);
/* Disable D cache */
write_aux_reg(ARC_REG_DC_CTRL, temp | IC_CTRL_CACHE_DISABLE);
#endif
return;
}
#define OP_INV 0x1
#define OP_FLUSH 0x2
#define OP_FLUSH_N_INV 0x3
#ifdef CONFIG_ARC_HAS_DCACHE
/***************************************************************
* Machine specific helpers for Entire D-Cache or Per Line ops
*/
static inline void wait_for_flush(void)
{
while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS)
;
}
/*
* Operation on Entire D-Cache
* @cacheop = {OP_INV, OP_FLUSH, OP_FLUSH_N_INV}
* Note that constant propagation ensures all the checks are gone
* in generated code
*/
static inline void __dc_entire_op(const int cacheop)
{
unsigned long flags, tmp = tmp;
int aux;
local_irq_save(flags);
if (cacheop == OP_FLUSH_N_INV) {
/* Dcache provides 2 cmd: FLUSH or INV
* INV inturn has sub-modes: DISCARD or FLUSH-BEFORE
* flush-n-inv is achieved by INV cmd but with IM=1
* Default INV sub-mode is DISCARD, which needs to be toggled
*/
tmp = read_aux_reg(ARC_REG_DC_CTRL);
write_aux_reg(ARC_REG_DC_CTRL, tmp | DC_CTRL_INV_MODE_FLUSH);
}
if (cacheop & OP_INV) /* Inv or flush-n-inv use same cmd reg */
aux = ARC_REG_DC_IVDC;
else
aux = ARC_REG_DC_FLSH;
write_aux_reg(aux, 0x1);
if (cacheop & OP_FLUSH) /* flush / flush-n-inv both wait */
wait_for_flush();
/* Switch back the DISCARD ONLY Invalidate mode */
if (cacheop == OP_FLUSH_N_INV)
write_aux_reg(ARC_REG_DC_CTRL, tmp & ~DC_CTRL_INV_MODE_FLUSH);
local_irq_restore(flags);
}
/*
* Per Line Operation on D-Cache
* Doesn't deal with type-of-op/IRQ-disabling/waiting-for-flush-to-complete
* It's sole purpose is to help gcc generate ZOL
*/
static inline void __dc_line_loop(unsigned long start, unsigned long sz,
int aux_reg)
{
int num_lines, slack;
/* Ensure we properly floor/ceil the non-line aligned/sized requests
* and have @start - aligned to cache line and integral @num_lines.
* This however can be avoided for page sized since:
* -@start will be cache-line aligned already (being page aligned)
* -@sz will be integral multiple of line size (being page sized).
*/
if (!(__builtin_constant_p(sz) && sz == PAGE_SIZE)) {
slack = start & ~DCACHE_LINE_MASK;
sz += slack;
start -= slack;
}
num_lines = DIV_ROUND_UP(sz, ARC_DCACHE_LINE_LEN);
while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
/*
* Just as for I$, in MMU v3, D$ ops also require
* "tag" bits in DC_PTAG, "index" bits in FLDL,IVDL ops
* But we pass phy addr for both. This works since Linux
* doesn't support aliasing configs for D$, yet.
* Thus paddr is enough to provide both tag and index.
*/
write_aux_reg(ARC_REG_DC_PTAG, start);
#endif
write_aux_reg(aux_reg, start);
start += ARC_DCACHE_LINE_LEN;
}
}
/*
* D-Cache : Per Line INV (discard or wback+discard) or FLUSH (wback)
*/
static inline void __dc_line_op(unsigned long start, unsigned long sz,
const int cacheop)
{
unsigned long flags, tmp = tmp;
int aux;
local_irq_save(flags);
if (cacheop == OP_FLUSH_N_INV) {
/*
* Dcache provides 2 cmd: FLUSH or INV
* INV inturn has sub-modes: DISCARD or FLUSH-BEFORE
* flush-n-inv is achieved by INV cmd but with IM=1
* Default INV sub-mode is DISCARD, which needs to be toggled
*/
tmp = read_aux_reg(ARC_REG_DC_CTRL);
write_aux_reg(ARC_REG_DC_CTRL, tmp | DC_CTRL_INV_MODE_FLUSH);
}
if (cacheop & OP_INV) /* Inv / flush-n-inv use same cmd reg */
aux = ARC_REG_DC_IVDL;
else
aux = ARC_REG_DC_FLDL;
__dc_line_loop(start, sz, aux);
if (cacheop & OP_FLUSH) /* flush / flush-n-inv both wait */
wait_for_flush();
/* Switch back the DISCARD ONLY Invalidate mode */
if (cacheop == OP_FLUSH_N_INV)
write_aux_reg(ARC_REG_DC_CTRL, tmp & ~DC_CTRL_INV_MODE_FLUSH);
local_irq_restore(flags);
}
#else
#define __dc_entire_op(cacheop)
#define __dc_line_op(start, sz, cacheop)
#endif /* CONFIG_ARC_HAS_DCACHE */
#ifdef CONFIG_ARC_HAS_ICACHE
/*
* I-Cache Aliasing in ARC700 VIPT caches
*
* For fetching code from I$, ARC700 uses vaddr (embedded in program code)
* to "index" into SET of cache-line and paddr from MMU to match the TAG
* in the WAYS of SET.
*
* However the CDU iterface (to flush/inv) lines from software, only takes
* paddr (to have simpler hardware interface). For simpler cases, using paddr
* alone suffices.
* e.g. 2-way-set-assoc, 16K I$ (8k MMU pg sz, 32b cache line size):
* way_sz = cache_sz / num_ways = 16k/2 = 8k
* num_sets = way_sz / line_sz = 8k/32 = 256 => 8 bits
* Ignoring the bottom 5 bits corresp to the off within a 32b cacheline,
* bits req for calc set-index = bits 12:5 (0 based). Since this range fits
* inside the bottom 13 bits of paddr, which are same for vaddr and paddr
* (with 8k pg sz), paddr alone can be safely used by CDU to unambigously
* locate a cache-line.
*
* However for a difft sized cache, say 32k I$, above math yields need
* for 14 bits of vaddr to locate a cache line, which can't be provided by
* paddr, since the bit 13 (0 based) might differ between the two.
*
* This lack of extra bits needed for correct line addressing, defines the
* classical problem of Cache aliasing with VIPT architectures
* num_aliases = 1 << extra_bits
* e.g. 2-way-set-assoc, 32K I$ with 8k MMU pg sz => 2 aliases
* 2-way-set-assoc, 64K I$ with 8k MMU pg sz => 4 aliases
* 2-way-set-assoc, 16K I$ with 8k MMU pg sz => NO aliases
*
* ------------------
* MMU v1/v2 (Fixed Page Size 8k)
* ------------------
* The solution was to provide CDU with these additonal vaddr bits. These
* would be bits [x:13], x would depend on cache-geom.
* H/w folks chose [17:13] to be a future safe range, and moreso these 5 bits
* of vaddr could easily be "stuffed" in the paddr as bits [4:0] since the
* orig 5 bits of paddr were anyways ignored by CDU line ops, as they
* represent the offset within cache-line. The adv of using this "clumsy"
* interface for additional info was no new reg was needed in CDU.
*
* 17:13 represented the max num of bits passable, actual bits needed were
* fewer, based on the num-of-aliases possible.
* -for 2 alias possibility, only bit 13 needed (32K cache)
* -for 4 alias possibility, bits 14:13 needed (64K cache)
*
* Since vaddr was not available for all instances of I$ flush req by core
* kernel, the only safe way (non-optimal though) was to kill all possible
* lines which could represent an alias (even if they didnt represent one
* in execution).
* e.g. for 64K I$, 4 aliases possible, so we did
* flush start
* flush start | 0x01
* flush start | 0x2
* flush start | 0x3
*
* The penalty was invoking the operation itself, since tag match is anyways
* paddr based, a line which didn't represent an alias would not match the
* paddr, hence wont be killed
*
* Note that aliasing concerns are independent of line-sz for a given cache
* geometry (size + set_assoc) because the extra bits required by line-sz are
* reduced from the set calc.
* e.g. 2-way-set-assoc, 32K I$ with 8k MMU pg sz and using math above
* 32b line-sz: 9 bits set-index-calc, 5 bits offset-in-line => 1 extra bit
* 64b line-sz: 8 bits set-index-calc, 6 bits offset-in-line => 1 extra bit
*
* ------------------
* MMU v3
* ------------------
* This ver of MMU supports var page sizes (1k-16k) - Linux will support
* 8k (default), 16k and 4k.
* However from hardware perspective, smaller page sizes aggrevate aliasing
* meaning more vaddr bits needed to disambiguate the cache-line-op ;
* the existing scheme of piggybacking won't work for certain configurations.
* Two new registers IC_PTAG and DC_PTAG inttoduced.
* "tag" bits are provided in PTAG, index bits in existing IVIL/IVDL/FLDL regs
*/
/***********************************************************
* Machine specific helpers for per line I-Cache invalidate.
* 3 routines to accpunt for 1, 2, 4 aliases possible
*/
static void __ic_line_inv_no_alias(unsigned long start, int num_lines)
{
while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
write_aux_reg(ARC_REG_IC_PTAG, start);
#endif
write_aux_reg(ARC_REG_IC_IVIL, start);
start += ARC_ICACHE_LINE_LEN;
}
}
static void __ic_line_inv_2_alias(unsigned long start, int num_lines)
{
while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
/*
* MMU v3, CDU prog model (for line ops) now uses a new IC_PTAG
* reg to pass the "tag" bits and existing IVIL reg only looks
* at bits relevant for "index" (details above)
* Programming Notes:
* -when writing tag to PTAG reg, bit chopping can be avoided,
* CDU ignores non-tag bits.
* -Ideally "index" must be computed from vaddr, but it is not
* avail in these rtns. So to be safe, we kill the lines in all
* possible indexes corresp to num of aliases possible for
* given cache config.
*/
write_aux_reg(ARC_REG_IC_PTAG, start);
write_aux_reg(ARC_REG_IC_IVIL,
start & ~(0x1 << PAGE_SHIFT));
write_aux_reg(ARC_REG_IC_IVIL, start | (0x1 << PAGE_SHIFT));
#else
write_aux_reg(ARC_REG_IC_IVIL, start);
write_aux_reg(ARC_REG_IC_IVIL, start | 0x01);
#endif
start += ARC_ICACHE_LINE_LEN;
}
}
static void __ic_line_inv_4_alias(unsigned long start, int num_lines)
{
while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
write_aux_reg(ARC_REG_IC_PTAG, start);
write_aux_reg(ARC_REG_IC_IVIL,
start & ~(0x3 << PAGE_SHIFT));
write_aux_reg(ARC_REG_IC_IVIL,
start & ~(0x2 << PAGE_SHIFT));
write_aux_reg(ARC_REG_IC_IVIL,
start & ~(0x1 << PAGE_SHIFT));
write_aux_reg(ARC_REG_IC_IVIL, start | (0x3 << PAGE_SHIFT));
#else
write_aux_reg(ARC_REG_IC_IVIL, start);
write_aux_reg(ARC_REG_IC_IVIL, start | 0x01);
write_aux_reg(ARC_REG_IC_IVIL, start | 0x02);
write_aux_reg(ARC_REG_IC_IVIL, start | 0x03);
#endif
start += ARC_ICACHE_LINE_LEN;
}
}
static void __ic_line_inv(unsigned long start, unsigned long sz)
{
unsigned long flags;
int num_lines, slack;
/*
* Ensure we properly floor/ceil the non-line aligned/sized requests
* and have @start - aligned to cache line, and integral @num_lines
* However page sized flushes can be compile time optimised.
* -@start will be cache-line aligned already (being page aligned)
* -@sz will be integral multiple of line size (being page sized).
*/
if (!(__builtin_constant_p(sz) && sz == PAGE_SIZE)) {
slack = start & ~ICACHE_LINE_MASK;
sz += slack;
start -= slack;
}
num_lines = DIV_ROUND_UP(sz, ARC_ICACHE_LINE_LEN);
local_irq_save(flags);
(*___flush_icache_rtn) (start, num_lines);
local_irq_restore(flags);
}
/* Unlike routines above, having vaddr for flush op (along with paddr),
* prevents the need to speculatively kill the lines in multiple sets
* based on ratio of way_sz : pg_sz
*/
static void __ic_line_inv_vaddr(unsigned long phy_start,
unsigned long vaddr, unsigned long sz)
{
unsigned long flags;
int num_lines, slack;
unsigned int addr;
slack = phy_start & ~ICACHE_LINE_MASK;
sz += slack;
phy_start -= slack;
num_lines = DIV_ROUND_UP(sz, ARC_ICACHE_LINE_LEN);
#if (CONFIG_ARC_MMU_VER > 2)
vaddr &= ~ICACHE_LINE_MASK;
addr = phy_start;
#else
/* bits 17:13 of vaddr go as bits 4:0 of paddr */
addr = phy_start | ((vaddr >> 13) & 0x1F);
#endif
local_irq_save(flags);
while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
/* tag comes from phy addr */
write_aux_reg(ARC_REG_IC_PTAG, addr);
/* index bits come from vaddr */
write_aux_reg(ARC_REG_IC_IVIL, vaddr);
vaddr += ARC_ICACHE_LINE_LEN;
#else
/* this paddr contains vaddrs bits as needed */
write_aux_reg(ARC_REG_IC_IVIL, addr);
#endif
addr += ARC_ICACHE_LINE_LEN;
}
local_irq_restore(flags);
}
#else
#define __ic_line_inv(start, sz)
#define __ic_line_inv_vaddr(pstart, vstart, sz)
#endif /* CONFIG_ARC_HAS_ICACHE */
/***********************************************************
* Exported APIs
*/
/* TBD: use pg_arch_1 to optimize this */
void flush_dcache_page(struct page *page)
{
__dc_line_op((unsigned long)page_address(page), PAGE_SIZE, OP_FLUSH);
}
EXPORT_SYMBOL(flush_dcache_page);
void dma_cache_wback_inv(unsigned long start, unsigned long sz)
{
__dc_line_op(start, sz, OP_FLUSH_N_INV);
}
EXPORT_SYMBOL(dma_cache_wback_inv);
void dma_cache_inv(unsigned long start, unsigned long sz)
{
__dc_line_op(start, sz, OP_INV);
}
EXPORT_SYMBOL(dma_cache_inv);
void dma_cache_wback(unsigned long start, unsigned long sz)
{
__dc_line_op(start, sz, OP_FLUSH);
}
EXPORT_SYMBOL(dma_cache_wback);
/*
* This is API for making I/D Caches consistent when modifying code
* (loadable modules, kprobes, etc)
* This is called on insmod, with kernel virtual address for CODE of
* the module. ARC cache maintenance ops require PHY address thus we
* need to convert vmalloc addr to PHY addr
*/
void flush_icache_range(unsigned long kstart, unsigned long kend)
{
unsigned int tot_sz, off, sz;
unsigned long phy, pfn;
unsigned long flags;
/* printk("Kernel Cache Cohenercy: %lx to %lx\n",kstart, kend); */
/* This is not the right API for user virtual address */
if (kstart < TASK_SIZE) {
BUG_ON("Flush icache range for user virtual addr space");
return;
}
/* Shortcut for bigger flush ranges.
* Here we don't care if this was kernel virtual or phy addr
*/
tot_sz = kend - kstart;
if (tot_sz > PAGE_SIZE) {
flush_cache_all();
return;
}
/* Case: Kernel Phy addr (0x8000_0000 onwards) */
if (likely(kstart > PAGE_OFFSET)) {
__ic_line_inv(kstart, kend - kstart);
__dc_line_op(kstart, kend - kstart, OP_FLUSH);
return;
}
/*
* Case: Kernel Vaddr (0x7000_0000 to 0x7fff_ffff)
* (1) ARC Cache Maintenance ops only take Phy addr, hence special
* handling of kernel vaddr.
*
* (2) Despite @tot_sz being < PAGE_SIZE (bigger cases handled already),
* it still needs to handle a 2 page scenario, where the range
* straddles across 2 virtual pages and hence need for loop
*/
while (tot_sz > 0) {
off = kstart % PAGE_SIZE;
pfn = vmalloc_to_pfn((void *)kstart);
phy = (pfn << PAGE_SHIFT) + off;
sz = min_t(unsigned int, tot_sz, PAGE_SIZE - off);
local_irq_save(flags);
__dc_line_op(phy, sz, OP_FLUSH);
__ic_line_inv(phy, sz);
local_irq_restore(flags);
kstart += sz;
tot_sz -= sz;
}
}
/*
* Optimised ver of flush_icache_range() with spec callers: ptrace/signals
* where vaddr is also available. This allows passing both vaddr and paddr
* bits to CDU for cache flush, short-circuting the current pessimistic algo
* which kills all possible aliases.
* An added adv of knowing that vaddr is user-vaddr avoids various checks
* and handling for k-vaddr, k-paddr as done in orig ver above
*/
void flush_icache_range_vaddr(unsigned long paddr, unsigned long u_vaddr,
int len)
{
__ic_line_inv_vaddr(paddr, u_vaddr, len);
__dc_line_op(paddr, len, OP_FLUSH);
}
/*
* XXX: This also needs to be optim using pg_arch_1
* This is called when a page-cache page is about to be mapped into a
* user process' address space. It offers an opportunity for a
* port to ensure d-cache/i-cache coherency if necessary.
*/
void flush_icache_page(struct vm_area_struct *vma, struct page *page)
{
if (!(vma->vm_flags & VM_EXEC))
return;
__ic_line_inv((unsigned long)page_address(page), PAGE_SIZE);
}
void flush_icache_all(void)
{
unsigned long flags;
local_irq_save(flags);
write_aux_reg(ARC_REG_IC_IVIC, 1);
/* lr will not complete till the icache inv operation is not over */
read_aux_reg(ARC_REG_IC_CTRL);
local_irq_restore(flags);
}
noinline void flush_cache_all(void)
{
unsigned long flags;
local_irq_save(flags);
flush_icache_all();
__dc_entire_op(OP_FLUSH_N_INV);
local_irq_restore(flags);
}
/**********************************************************************
* Explicit Cache flush request from user space via syscall
* Needed for JITs which generate code on the fly
*/
SYSCALL_DEFINE3(cacheflush, uint32_t, start, uint32_t, sz, uint32_t, flags)
{
/* TBD: optimize this */
flush_cache_all();
return 0;
}