OpenCloudOS-Kernel/arch/x86/kernel/apic/io_apic.c

4182 lines
99 KiB
C

/*
* Intel IO-APIC support for multi-Pentium hosts.
*
* Copyright (C) 1997, 1998, 1999, 2000, 2009 Ingo Molnar, Hajnalka Szabo
*
* Many thanks to Stig Venaas for trying out countless experimental
* patches and reporting/debugging problems patiently!
*
* (c) 1999, Multiple IO-APIC support, developed by
* Ken-ichi Yaku <yaku@css1.kbnes.nec.co.jp> and
* Hidemi Kishimoto <kisimoto@css1.kbnes.nec.co.jp>,
* further tested and cleaned up by Zach Brown <zab@redhat.com>
* and Ingo Molnar <mingo@redhat.com>
*
* Fixes
* Maciej W. Rozycki : Bits for genuine 82489DX APICs;
* thanks to Eric Gilmore
* and Rolf G. Tews
* for testing these extensively
* Paul Diefenbaugh : Added full ACPI support
*/
#include <linux/mm.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/pci.h>
#include <linux/mc146818rtc.h>
#include <linux/compiler.h>
#include <linux/acpi.h>
#include <linux/module.h>
#include <linux/sysdev.h>
#include <linux/msi.h>
#include <linux/htirq.h>
#include <linux/freezer.h>
#include <linux/kthread.h>
#include <linux/jiffies.h> /* time_after() */
#ifdef CONFIG_ACPI
#include <acpi/acpi_bus.h>
#endif
#include <linux/bootmem.h>
#include <linux/dmar.h>
#include <linux/hpet.h>
#include <asm/idle.h>
#include <asm/io.h>
#include <asm/smp.h>
#include <asm/cpu.h>
#include <asm/desc.h>
#include <asm/proto.h>
#include <asm/acpi.h>
#include <asm/dma.h>
#include <asm/timer.h>
#include <asm/i8259.h>
#include <asm/nmi.h>
#include <asm/msidef.h>
#include <asm/hypertransport.h>
#include <asm/setup.h>
#include <asm/irq_remapping.h>
#include <asm/hpet.h>
#include <asm/hw_irq.h>
#include <asm/apic.h>
#define __apicdebuginit(type) static type __init
#define for_each_irq_pin(entry, head) \
for (entry = head; entry; entry = entry->next)
/*
* Is the SiS APIC rmw bug present ?
* -1 = don't know, 0 = no, 1 = yes
*/
int sis_apic_bug = -1;
static DEFINE_SPINLOCK(ioapic_lock);
static DEFINE_SPINLOCK(vector_lock);
/*
* # of IRQ routing registers
*/
int nr_ioapic_registers[MAX_IO_APICS];
/* I/O APIC entries */
struct mpc_ioapic mp_ioapics[MAX_IO_APICS];
int nr_ioapics;
/* IO APIC gsi routing info */
struct mp_ioapic_gsi mp_gsi_routing[MAX_IO_APICS];
/* MP IRQ source entries */
struct mpc_intsrc mp_irqs[MAX_IRQ_SOURCES];
/* # of MP IRQ source entries */
int mp_irq_entries;
/* Number of legacy interrupts */
static int nr_legacy_irqs __read_mostly = NR_IRQS_LEGACY;
/* GSI interrupts */
static int nr_irqs_gsi = NR_IRQS_LEGACY;
#if defined (CONFIG_MCA) || defined (CONFIG_EISA)
int mp_bus_id_to_type[MAX_MP_BUSSES];
#endif
DECLARE_BITMAP(mp_bus_not_pci, MAX_MP_BUSSES);
int skip_ioapic_setup;
void arch_disable_smp_support(void)
{
#ifdef CONFIG_PCI
noioapicquirk = 1;
noioapicreroute = -1;
#endif
skip_ioapic_setup = 1;
}
static int __init parse_noapic(char *str)
{
/* disable IO-APIC */
arch_disable_smp_support();
return 0;
}
early_param("noapic", parse_noapic);
struct irq_pin_list {
int apic, pin;
struct irq_pin_list *next;
};
static struct irq_pin_list *get_one_free_irq_2_pin(int node)
{
struct irq_pin_list *pin;
pin = kzalloc_node(sizeof(*pin), GFP_ATOMIC, node);
return pin;
}
/* irq_cfg is indexed by the sum of all RTEs in all I/O APICs. */
#ifdef CONFIG_SPARSE_IRQ
static struct irq_cfg irq_cfgx[] = {
#else
static struct irq_cfg irq_cfgx[NR_IRQS] = {
#endif
[0] = { .vector = IRQ0_VECTOR, },
[1] = { .vector = IRQ1_VECTOR, },
[2] = { .vector = IRQ2_VECTOR, },
[3] = { .vector = IRQ3_VECTOR, },
[4] = { .vector = IRQ4_VECTOR, },
[5] = { .vector = IRQ5_VECTOR, },
[6] = { .vector = IRQ6_VECTOR, },
[7] = { .vector = IRQ7_VECTOR, },
[8] = { .vector = IRQ8_VECTOR, },
[9] = { .vector = IRQ9_VECTOR, },
[10] = { .vector = IRQ10_VECTOR, },
[11] = { .vector = IRQ11_VECTOR, },
[12] = { .vector = IRQ12_VECTOR, },
[13] = { .vector = IRQ13_VECTOR, },
[14] = { .vector = IRQ14_VECTOR, },
[15] = { .vector = IRQ15_VECTOR, },
};
void __init io_apic_disable_legacy(void)
{
nr_legacy_irqs = 0;
nr_irqs_gsi = 0;
}
int __init arch_early_irq_init(void)
{
struct irq_cfg *cfg;
struct irq_desc *desc;
int count;
int node;
int i;
cfg = irq_cfgx;
count = ARRAY_SIZE(irq_cfgx);
node= cpu_to_node(boot_cpu_id);
for (i = 0; i < count; i++) {
desc = irq_to_desc(i);
desc->chip_data = &cfg[i];
zalloc_cpumask_var_node(&cfg[i].domain, GFP_NOWAIT, node);
zalloc_cpumask_var_node(&cfg[i].old_domain, GFP_NOWAIT, node);
if (i < nr_legacy_irqs)
cpumask_setall(cfg[i].domain);
}
return 0;
}
#ifdef CONFIG_SPARSE_IRQ
struct irq_cfg *irq_cfg(unsigned int irq)
{
struct irq_cfg *cfg = NULL;
struct irq_desc *desc;
desc = irq_to_desc(irq);
if (desc)
cfg = desc->chip_data;
return cfg;
}
static struct irq_cfg *get_one_free_irq_cfg(int node)
{
struct irq_cfg *cfg;
cfg = kzalloc_node(sizeof(*cfg), GFP_ATOMIC, node);
if (cfg) {
if (!zalloc_cpumask_var_node(&cfg->domain, GFP_ATOMIC, node)) {
kfree(cfg);
cfg = NULL;
} else if (!zalloc_cpumask_var_node(&cfg->old_domain,
GFP_ATOMIC, node)) {
free_cpumask_var(cfg->domain);
kfree(cfg);
cfg = NULL;
}
}
return cfg;
}
int arch_init_chip_data(struct irq_desc *desc, int node)
{
struct irq_cfg *cfg;
cfg = desc->chip_data;
if (!cfg) {
desc->chip_data = get_one_free_irq_cfg(node);
if (!desc->chip_data) {
printk(KERN_ERR "can not alloc irq_cfg\n");
BUG_ON(1);
}
}
return 0;
}
/* for move_irq_desc */
static void
init_copy_irq_2_pin(struct irq_cfg *old_cfg, struct irq_cfg *cfg, int node)
{
struct irq_pin_list *old_entry, *head, *tail, *entry;
cfg->irq_2_pin = NULL;
old_entry = old_cfg->irq_2_pin;
if (!old_entry)
return;
entry = get_one_free_irq_2_pin(node);
if (!entry)
return;
entry->apic = old_entry->apic;
entry->pin = old_entry->pin;
head = entry;
tail = entry;
old_entry = old_entry->next;
while (old_entry) {
entry = get_one_free_irq_2_pin(node);
if (!entry) {
entry = head;
while (entry) {
head = entry->next;
kfree(entry);
entry = head;
}
/* still use the old one */
return;
}
entry->apic = old_entry->apic;
entry->pin = old_entry->pin;
tail->next = entry;
tail = entry;
old_entry = old_entry->next;
}
tail->next = NULL;
cfg->irq_2_pin = head;
}
static void free_irq_2_pin(struct irq_cfg *old_cfg, struct irq_cfg *cfg)
{
struct irq_pin_list *entry, *next;
if (old_cfg->irq_2_pin == cfg->irq_2_pin)
return;
entry = old_cfg->irq_2_pin;
while (entry) {
next = entry->next;
kfree(entry);
entry = next;
}
old_cfg->irq_2_pin = NULL;
}
void arch_init_copy_chip_data(struct irq_desc *old_desc,
struct irq_desc *desc, int node)
{
struct irq_cfg *cfg;
struct irq_cfg *old_cfg;
cfg = get_one_free_irq_cfg(node);
if (!cfg)
return;
desc->chip_data = cfg;
old_cfg = old_desc->chip_data;
memcpy(cfg, old_cfg, sizeof(struct irq_cfg));
init_copy_irq_2_pin(old_cfg, cfg, node);
}
static void free_irq_cfg(struct irq_cfg *old_cfg)
{
kfree(old_cfg);
}
void arch_free_chip_data(struct irq_desc *old_desc, struct irq_desc *desc)
{
struct irq_cfg *old_cfg, *cfg;
old_cfg = old_desc->chip_data;
cfg = desc->chip_data;
if (old_cfg == cfg)
return;
if (old_cfg) {
free_irq_2_pin(old_cfg, cfg);
free_irq_cfg(old_cfg);
old_desc->chip_data = NULL;
}
}
/* end for move_irq_desc */
#else
struct irq_cfg *irq_cfg(unsigned int irq)
{
return irq < nr_irqs ? irq_cfgx + irq : NULL;
}
#endif
struct io_apic {
unsigned int index;
unsigned int unused[3];
unsigned int data;
unsigned int unused2[11];
unsigned int eoi;
};
static __attribute_const__ struct io_apic __iomem *io_apic_base(int idx)
{
return (void __iomem *) __fix_to_virt(FIX_IO_APIC_BASE_0 + idx)
+ (mp_ioapics[idx].apicaddr & ~PAGE_MASK);
}
static inline void io_apic_eoi(unsigned int apic, unsigned int vector)
{
struct io_apic __iomem *io_apic = io_apic_base(apic);
writel(vector, &io_apic->eoi);
}
static inline unsigned int io_apic_read(unsigned int apic, unsigned int reg)
{
struct io_apic __iomem *io_apic = io_apic_base(apic);
writel(reg, &io_apic->index);
return readl(&io_apic->data);
}
static inline void io_apic_write(unsigned int apic, unsigned int reg, unsigned int value)
{
struct io_apic __iomem *io_apic = io_apic_base(apic);
writel(reg, &io_apic->index);
writel(value, &io_apic->data);
}
/*
* Re-write a value: to be used for read-modify-write
* cycles where the read already set up the index register.
*
* Older SiS APIC requires we rewrite the index register
*/
static inline void io_apic_modify(unsigned int apic, unsigned int reg, unsigned int value)
{
struct io_apic __iomem *io_apic = io_apic_base(apic);
if (sis_apic_bug)
writel(reg, &io_apic->index);
writel(value, &io_apic->data);
}
static bool io_apic_level_ack_pending(struct irq_cfg *cfg)
{
struct irq_pin_list *entry;
unsigned long flags;
spin_lock_irqsave(&ioapic_lock, flags);
for_each_irq_pin(entry, cfg->irq_2_pin) {
unsigned int reg;
int pin;
pin = entry->pin;
reg = io_apic_read(entry->apic, 0x10 + pin*2);
/* Is the remote IRR bit set? */
if (reg & IO_APIC_REDIR_REMOTE_IRR) {
spin_unlock_irqrestore(&ioapic_lock, flags);
return true;
}
}
spin_unlock_irqrestore(&ioapic_lock, flags);
return false;
}
union entry_union {
struct { u32 w1, w2; };
struct IO_APIC_route_entry entry;
};
static struct IO_APIC_route_entry ioapic_read_entry(int apic, int pin)
{
union entry_union eu;
unsigned long flags;
spin_lock_irqsave(&ioapic_lock, flags);
eu.w1 = io_apic_read(apic, 0x10 + 2 * pin);
eu.w2 = io_apic_read(apic, 0x11 + 2 * pin);
spin_unlock_irqrestore(&ioapic_lock, flags);
return eu.entry;
}
/*
* When we write a new IO APIC routing entry, we need to write the high
* word first! If the mask bit in the low word is clear, we will enable
* the interrupt, and we need to make sure the entry is fully populated
* before that happens.
*/
static void
__ioapic_write_entry(int apic, int pin, struct IO_APIC_route_entry e)
{
union entry_union eu = {{0, 0}};
eu.entry = e;
io_apic_write(apic, 0x11 + 2*pin, eu.w2);
io_apic_write(apic, 0x10 + 2*pin, eu.w1);
}
void ioapic_write_entry(int apic, int pin, struct IO_APIC_route_entry e)
{
unsigned long flags;
spin_lock_irqsave(&ioapic_lock, flags);
__ioapic_write_entry(apic, pin, e);
spin_unlock_irqrestore(&ioapic_lock, flags);
}
/*
* When we mask an IO APIC routing entry, we need to write the low
* word first, in order to set the mask bit before we change the
* high bits!
*/
static void ioapic_mask_entry(int apic, int pin)
{
unsigned long flags;
union entry_union eu = { .entry.mask = 1 };
spin_lock_irqsave(&ioapic_lock, flags);
io_apic_write(apic, 0x10 + 2*pin, eu.w1);
io_apic_write(apic, 0x11 + 2*pin, eu.w2);
spin_unlock_irqrestore(&ioapic_lock, flags);
}
/*
* The common case is 1:1 IRQ<->pin mappings. Sometimes there are
* shared ISA-space IRQs, so we have to support them. We are super
* fast in the common case, and fast for shared ISA-space IRQs.
*/
static int
add_pin_to_irq_node_nopanic(struct irq_cfg *cfg, int node, int apic, int pin)
{
struct irq_pin_list **last, *entry;
/* don't allow duplicates */
last = &cfg->irq_2_pin;
for_each_irq_pin(entry, cfg->irq_2_pin) {
if (entry->apic == apic && entry->pin == pin)
return 0;
last = &entry->next;
}
entry = get_one_free_irq_2_pin(node);
if (!entry) {
printk(KERN_ERR "can not alloc irq_pin_list (%d,%d,%d)\n",
node, apic, pin);
return -ENOMEM;
}
entry->apic = apic;
entry->pin = pin;
*last = entry;
return 0;
}
static void add_pin_to_irq_node(struct irq_cfg *cfg, int node, int apic, int pin)
{
if (add_pin_to_irq_node_nopanic(cfg, node, apic, pin))
panic("IO-APIC: failed to add irq-pin. Can not proceed\n");
}
/*
* Reroute an IRQ to a different pin.
*/
static void __init replace_pin_at_irq_node(struct irq_cfg *cfg, int node,
int oldapic, int oldpin,
int newapic, int newpin)
{
struct irq_pin_list *entry;
for_each_irq_pin(entry, cfg->irq_2_pin) {
if (entry->apic == oldapic && entry->pin == oldpin) {
entry->apic = newapic;
entry->pin = newpin;
/* every one is different, right? */
return;
}
}
/* old apic/pin didn't exist, so just add new ones */
add_pin_to_irq_node(cfg, node, newapic, newpin);
}
static void io_apic_modify_irq(struct irq_cfg *cfg,
int mask_and, int mask_or,
void (*final)(struct irq_pin_list *entry))
{
int pin;
struct irq_pin_list *entry;
for_each_irq_pin(entry, cfg->irq_2_pin) {
unsigned int reg;
pin = entry->pin;
reg = io_apic_read(entry->apic, 0x10 + pin * 2);
reg &= mask_and;
reg |= mask_or;
io_apic_modify(entry->apic, 0x10 + pin * 2, reg);
if (final)
final(entry);
}
}
static void __unmask_IO_APIC_irq(struct irq_cfg *cfg)
{
io_apic_modify_irq(cfg, ~IO_APIC_REDIR_MASKED, 0, NULL);
}
static void io_apic_sync(struct irq_pin_list *entry)
{
/*
* Synchronize the IO-APIC and the CPU by doing
* a dummy read from the IO-APIC
*/
struct io_apic __iomem *io_apic;
io_apic = io_apic_base(entry->apic);
readl(&io_apic->data);
}
static void __mask_IO_APIC_irq(struct irq_cfg *cfg)
{
io_apic_modify_irq(cfg, ~0, IO_APIC_REDIR_MASKED, &io_apic_sync);
}
static void __mask_and_edge_IO_APIC_irq(struct irq_cfg *cfg)
{
io_apic_modify_irq(cfg, ~IO_APIC_REDIR_LEVEL_TRIGGER,
IO_APIC_REDIR_MASKED, NULL);
}
static void __unmask_and_level_IO_APIC_irq(struct irq_cfg *cfg)
{
io_apic_modify_irq(cfg, ~IO_APIC_REDIR_MASKED,
IO_APIC_REDIR_LEVEL_TRIGGER, NULL);
}
static void mask_IO_APIC_irq_desc(struct irq_desc *desc)
{
struct irq_cfg *cfg = desc->chip_data;
unsigned long flags;
BUG_ON(!cfg);
spin_lock_irqsave(&ioapic_lock, flags);
__mask_IO_APIC_irq(cfg);
spin_unlock_irqrestore(&ioapic_lock, flags);
}
static void unmask_IO_APIC_irq_desc(struct irq_desc *desc)
{
struct irq_cfg *cfg = desc->chip_data;
unsigned long flags;
spin_lock_irqsave(&ioapic_lock, flags);
__unmask_IO_APIC_irq(cfg);
spin_unlock_irqrestore(&ioapic_lock, flags);
}
static void mask_IO_APIC_irq(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
mask_IO_APIC_irq_desc(desc);
}
static void unmask_IO_APIC_irq(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
unmask_IO_APIC_irq_desc(desc);
}
static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin)
{
struct IO_APIC_route_entry entry;
/* Check delivery_mode to be sure we're not clearing an SMI pin */
entry = ioapic_read_entry(apic, pin);
if (entry.delivery_mode == dest_SMI)
return;
/*
* Disable it in the IO-APIC irq-routing table:
*/
ioapic_mask_entry(apic, pin);
}
static void clear_IO_APIC (void)
{
int apic, pin;
for (apic = 0; apic < nr_ioapics; apic++)
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++)
clear_IO_APIC_pin(apic, pin);
}
#ifdef CONFIG_X86_32
/*
* support for broken MP BIOSs, enables hand-redirection of PIRQ0-7 to
* specific CPU-side IRQs.
*/
#define MAX_PIRQS 8
static int pirq_entries[MAX_PIRQS] = {
[0 ... MAX_PIRQS - 1] = -1
};
static int __init ioapic_pirq_setup(char *str)
{
int i, max;
int ints[MAX_PIRQS+1];
get_options(str, ARRAY_SIZE(ints), ints);
apic_printk(APIC_VERBOSE, KERN_INFO
"PIRQ redirection, working around broken MP-BIOS.\n");
max = MAX_PIRQS;
if (ints[0] < MAX_PIRQS)
max = ints[0];
for (i = 0; i < max; i++) {
apic_printk(APIC_VERBOSE, KERN_DEBUG
"... PIRQ%d -> IRQ %d\n", i, ints[i+1]);
/*
* PIRQs are mapped upside down, usually.
*/
pirq_entries[MAX_PIRQS-i-1] = ints[i+1];
}
return 1;
}
__setup("pirq=", ioapic_pirq_setup);
#endif /* CONFIG_X86_32 */
struct IO_APIC_route_entry **alloc_ioapic_entries(void)
{
int apic;
struct IO_APIC_route_entry **ioapic_entries;
ioapic_entries = kzalloc(sizeof(*ioapic_entries) * nr_ioapics,
GFP_ATOMIC);
if (!ioapic_entries)
return 0;
for (apic = 0; apic < nr_ioapics; apic++) {
ioapic_entries[apic] =
kzalloc(sizeof(struct IO_APIC_route_entry) *
nr_ioapic_registers[apic], GFP_ATOMIC);
if (!ioapic_entries[apic])
goto nomem;
}
return ioapic_entries;
nomem:
while (--apic >= 0)
kfree(ioapic_entries[apic]);
kfree(ioapic_entries);
return 0;
}
/*
* Saves all the IO-APIC RTE's
*/
int save_IO_APIC_setup(struct IO_APIC_route_entry **ioapic_entries)
{
int apic, pin;
if (!ioapic_entries)
return -ENOMEM;
for (apic = 0; apic < nr_ioapics; apic++) {
if (!ioapic_entries[apic])
return -ENOMEM;
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++)
ioapic_entries[apic][pin] =
ioapic_read_entry(apic, pin);
}
return 0;
}
/*
* Mask all IO APIC entries.
*/
void mask_IO_APIC_setup(struct IO_APIC_route_entry **ioapic_entries)
{
int apic, pin;
if (!ioapic_entries)
return;
for (apic = 0; apic < nr_ioapics; apic++) {
if (!ioapic_entries[apic])
break;
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++) {
struct IO_APIC_route_entry entry;
entry = ioapic_entries[apic][pin];
if (!entry.mask) {
entry.mask = 1;
ioapic_write_entry(apic, pin, entry);
}
}
}
}
/*
* Restore IO APIC entries which was saved in ioapic_entries.
*/
int restore_IO_APIC_setup(struct IO_APIC_route_entry **ioapic_entries)
{
int apic, pin;
if (!ioapic_entries)
return -ENOMEM;
for (apic = 0; apic < nr_ioapics; apic++) {
if (!ioapic_entries[apic])
return -ENOMEM;
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++)
ioapic_write_entry(apic, pin,
ioapic_entries[apic][pin]);
}
return 0;
}
void free_ioapic_entries(struct IO_APIC_route_entry **ioapic_entries)
{
int apic;
for (apic = 0; apic < nr_ioapics; apic++)
kfree(ioapic_entries[apic]);
kfree(ioapic_entries);
}
/*
* Find the IRQ entry number of a certain pin.
*/
static int find_irq_entry(int apic, int pin, int type)
{
int i;
for (i = 0; i < mp_irq_entries; i++)
if (mp_irqs[i].irqtype == type &&
(mp_irqs[i].dstapic == mp_ioapics[apic].apicid ||
mp_irqs[i].dstapic == MP_APIC_ALL) &&
mp_irqs[i].dstirq == pin)
return i;
return -1;
}
/*
* Find the pin to which IRQ[irq] (ISA) is connected
*/
static int __init find_isa_irq_pin(int irq, int type)
{
int i;
for (i = 0; i < mp_irq_entries; i++) {
int lbus = mp_irqs[i].srcbus;
if (test_bit(lbus, mp_bus_not_pci) &&
(mp_irqs[i].irqtype == type) &&
(mp_irqs[i].srcbusirq == irq))
return mp_irqs[i].dstirq;
}
return -1;
}
static int __init find_isa_irq_apic(int irq, int type)
{
int i;
for (i = 0; i < mp_irq_entries; i++) {
int lbus = mp_irqs[i].srcbus;
if (test_bit(lbus, mp_bus_not_pci) &&
(mp_irqs[i].irqtype == type) &&
(mp_irqs[i].srcbusirq == irq))
break;
}
if (i < mp_irq_entries) {
int apic;
for(apic = 0; apic < nr_ioapics; apic++) {
if (mp_ioapics[apic].apicid == mp_irqs[i].dstapic)
return apic;
}
}
return -1;
}
#if defined(CONFIG_EISA) || defined(CONFIG_MCA)
/*
* EISA Edge/Level control register, ELCR
*/
static int EISA_ELCR(unsigned int irq)
{
if (irq < nr_legacy_irqs) {
unsigned int port = 0x4d0 + (irq >> 3);
return (inb(port) >> (irq & 7)) & 1;
}
apic_printk(APIC_VERBOSE, KERN_INFO
"Broken MPtable reports ISA irq %d\n", irq);
return 0;
}
#endif
/* ISA interrupts are always polarity zero edge triggered,
* when listed as conforming in the MP table. */
#define default_ISA_trigger(idx) (0)
#define default_ISA_polarity(idx) (0)
/* EISA interrupts are always polarity zero and can be edge or level
* trigger depending on the ELCR value. If an interrupt is listed as
* EISA conforming in the MP table, that means its trigger type must
* be read in from the ELCR */
#define default_EISA_trigger(idx) (EISA_ELCR(mp_irqs[idx].srcbusirq))
#define default_EISA_polarity(idx) default_ISA_polarity(idx)
/* PCI interrupts are always polarity one level triggered,
* when listed as conforming in the MP table. */
#define default_PCI_trigger(idx) (1)
#define default_PCI_polarity(idx) (1)
/* MCA interrupts are always polarity zero level triggered,
* when listed as conforming in the MP table. */
#define default_MCA_trigger(idx) (1)
#define default_MCA_polarity(idx) default_ISA_polarity(idx)
static int MPBIOS_polarity(int idx)
{
int bus = mp_irqs[idx].srcbus;
int polarity;
/*
* Determine IRQ line polarity (high active or low active):
*/
switch (mp_irqs[idx].irqflag & 3)
{
case 0: /* conforms, ie. bus-type dependent polarity */
if (test_bit(bus, mp_bus_not_pci))
polarity = default_ISA_polarity(idx);
else
polarity = default_PCI_polarity(idx);
break;
case 1: /* high active */
{
polarity = 0;
break;
}
case 2: /* reserved */
{
printk(KERN_WARNING "broken BIOS!!\n");
polarity = 1;
break;
}
case 3: /* low active */
{
polarity = 1;
break;
}
default: /* invalid */
{
printk(KERN_WARNING "broken BIOS!!\n");
polarity = 1;
break;
}
}
return polarity;
}
static int MPBIOS_trigger(int idx)
{
int bus = mp_irqs[idx].srcbus;
int trigger;
/*
* Determine IRQ trigger mode (edge or level sensitive):
*/
switch ((mp_irqs[idx].irqflag>>2) & 3)
{
case 0: /* conforms, ie. bus-type dependent */
if (test_bit(bus, mp_bus_not_pci))
trigger = default_ISA_trigger(idx);
else
trigger = default_PCI_trigger(idx);
#if defined(CONFIG_EISA) || defined(CONFIG_MCA)
switch (mp_bus_id_to_type[bus]) {
case MP_BUS_ISA: /* ISA pin */
{
/* set before the switch */
break;
}
case MP_BUS_EISA: /* EISA pin */
{
trigger = default_EISA_trigger(idx);
break;
}
case MP_BUS_PCI: /* PCI pin */
{
/* set before the switch */
break;
}
case MP_BUS_MCA: /* MCA pin */
{
trigger = default_MCA_trigger(idx);
break;
}
default:
{
printk(KERN_WARNING "broken BIOS!!\n");
trigger = 1;
break;
}
}
#endif
break;
case 1: /* edge */
{
trigger = 0;
break;
}
case 2: /* reserved */
{
printk(KERN_WARNING "broken BIOS!!\n");
trigger = 1;
break;
}
case 3: /* level */
{
trigger = 1;
break;
}
default: /* invalid */
{
printk(KERN_WARNING "broken BIOS!!\n");
trigger = 0;
break;
}
}
return trigger;
}
static inline int irq_polarity(int idx)
{
return MPBIOS_polarity(idx);
}
static inline int irq_trigger(int idx)
{
return MPBIOS_trigger(idx);
}
int (*ioapic_renumber_irq)(int ioapic, int irq);
static int pin_2_irq(int idx, int apic, int pin)
{
int irq, i;
int bus = mp_irqs[idx].srcbus;
/*
* Debugging check, we are in big trouble if this message pops up!
*/
if (mp_irqs[idx].dstirq != pin)
printk(KERN_ERR "broken BIOS or MPTABLE parser, ayiee!!\n");
if (test_bit(bus, mp_bus_not_pci)) {
irq = mp_irqs[idx].srcbusirq;
} else {
/*
* PCI IRQs are mapped in order
*/
i = irq = 0;
while (i < apic)
irq += nr_ioapic_registers[i++];
irq += pin;
/*
* For MPS mode, so far only needed by ES7000 platform
*/
if (ioapic_renumber_irq)
irq = ioapic_renumber_irq(apic, irq);
}
#ifdef CONFIG_X86_32
/*
* PCI IRQ command line redirection. Yes, limits are hardcoded.
*/
if ((pin >= 16) && (pin <= 23)) {
if (pirq_entries[pin-16] != -1) {
if (!pirq_entries[pin-16]) {
apic_printk(APIC_VERBOSE, KERN_DEBUG
"disabling PIRQ%d\n", pin-16);
} else {
irq = pirq_entries[pin-16];
apic_printk(APIC_VERBOSE, KERN_DEBUG
"using PIRQ%d -> IRQ %d\n",
pin-16, irq);
}
}
}
#endif
return irq;
}
/*
* Find a specific PCI IRQ entry.
* Not an __init, possibly needed by modules
*/
int IO_APIC_get_PCI_irq_vector(int bus, int slot, int pin,
struct io_apic_irq_attr *irq_attr)
{
int apic, i, best_guess = -1;
apic_printk(APIC_DEBUG,
"querying PCI -> IRQ mapping bus:%d, slot:%d, pin:%d.\n",
bus, slot, pin);
if (test_bit(bus, mp_bus_not_pci)) {
apic_printk(APIC_VERBOSE,
"PCI BIOS passed nonexistent PCI bus %d!\n", bus);
return -1;
}
for (i = 0; i < mp_irq_entries; i++) {
int lbus = mp_irqs[i].srcbus;
for (apic = 0; apic < nr_ioapics; apic++)
if (mp_ioapics[apic].apicid == mp_irqs[i].dstapic ||
mp_irqs[i].dstapic == MP_APIC_ALL)
break;
if (!test_bit(lbus, mp_bus_not_pci) &&
!mp_irqs[i].irqtype &&
(bus == lbus) &&
(slot == ((mp_irqs[i].srcbusirq >> 2) & 0x1f))) {
int irq = pin_2_irq(i, apic, mp_irqs[i].dstirq);
if (!(apic || IO_APIC_IRQ(irq)))
continue;
if (pin == (mp_irqs[i].srcbusirq & 3)) {
set_io_apic_irq_attr(irq_attr, apic,
mp_irqs[i].dstirq,
irq_trigger(i),
irq_polarity(i));
return irq;
}
/*
* Use the first all-but-pin matching entry as a
* best-guess fuzzy result for broken mptables.
*/
if (best_guess < 0) {
set_io_apic_irq_attr(irq_attr, apic,
mp_irqs[i].dstirq,
irq_trigger(i),
irq_polarity(i));
best_guess = irq;
}
}
}
return best_guess;
}
EXPORT_SYMBOL(IO_APIC_get_PCI_irq_vector);
void lock_vector_lock(void)
{
/* Used to the online set of cpus does not change
* during assign_irq_vector.
*/
spin_lock(&vector_lock);
}
void unlock_vector_lock(void)
{
spin_unlock(&vector_lock);
}
static int
__assign_irq_vector(int irq, struct irq_cfg *cfg, const struct cpumask *mask)
{
/*
* NOTE! The local APIC isn't very good at handling
* multiple interrupts at the same interrupt level.
* As the interrupt level is determined by taking the
* vector number and shifting that right by 4, we
* want to spread these out a bit so that they don't
* all fall in the same interrupt level.
*
* Also, we've got to be careful not to trash gate
* 0x80, because int 0x80 is hm, kind of importantish. ;)
*/
static int current_vector = FIRST_DEVICE_VECTOR, current_offset = 0;
unsigned int old_vector;
int cpu, err;
cpumask_var_t tmp_mask;
if (cfg->move_in_progress)
return -EBUSY;
if (!alloc_cpumask_var(&tmp_mask, GFP_ATOMIC))
return -ENOMEM;
old_vector = cfg->vector;
if (old_vector) {
cpumask_and(tmp_mask, mask, cpu_online_mask);
cpumask_and(tmp_mask, cfg->domain, tmp_mask);
if (!cpumask_empty(tmp_mask)) {
free_cpumask_var(tmp_mask);
return 0;
}
}
/* Only try and allocate irqs on cpus that are present */
err = -ENOSPC;
for_each_cpu_and(cpu, mask, cpu_online_mask) {
int new_cpu;
int vector, offset;
apic->vector_allocation_domain(cpu, tmp_mask);
vector = current_vector;
offset = current_offset;
next:
vector += 8;
if (vector >= first_system_vector) {
/* If out of vectors on large boxen, must share them. */
offset = (offset + 1) % 8;
vector = FIRST_DEVICE_VECTOR + offset;
}
if (unlikely(current_vector == vector))
continue;
if (test_bit(vector, used_vectors))
goto next;
for_each_cpu_and(new_cpu, tmp_mask, cpu_online_mask)
if (per_cpu(vector_irq, new_cpu)[vector] != -1)
goto next;
/* Found one! */
current_vector = vector;
current_offset = offset;
if (old_vector) {
cfg->move_in_progress = 1;
cpumask_copy(cfg->old_domain, cfg->domain);
}
for_each_cpu_and(new_cpu, tmp_mask, cpu_online_mask)
per_cpu(vector_irq, new_cpu)[vector] = irq;
cfg->vector = vector;
cpumask_copy(cfg->domain, tmp_mask);
err = 0;
break;
}
free_cpumask_var(tmp_mask);
return err;
}
int assign_irq_vector(int irq, struct irq_cfg *cfg, const struct cpumask *mask)
{
int err;
unsigned long flags;
spin_lock_irqsave(&vector_lock, flags);
err = __assign_irq_vector(irq, cfg, mask);
spin_unlock_irqrestore(&vector_lock, flags);
return err;
}
static void __clear_irq_vector(int irq, struct irq_cfg *cfg)
{
int cpu, vector;
BUG_ON(!cfg->vector);
vector = cfg->vector;
for_each_cpu_and(cpu, cfg->domain, cpu_online_mask)
per_cpu(vector_irq, cpu)[vector] = -1;
cfg->vector = 0;
cpumask_clear(cfg->domain);
if (likely(!cfg->move_in_progress))
return;
for_each_cpu_and(cpu, cfg->old_domain, cpu_online_mask) {
for (vector = FIRST_EXTERNAL_VECTOR; vector < NR_VECTORS;
vector++) {
if (per_cpu(vector_irq, cpu)[vector] != irq)
continue;
per_cpu(vector_irq, cpu)[vector] = -1;
break;
}
}
cfg->move_in_progress = 0;
}
void __setup_vector_irq(int cpu)
{
/* Initialize vector_irq on a new cpu */
/* This function must be called with vector_lock held */
int irq, vector;
struct irq_cfg *cfg;
struct irq_desc *desc;
/* Mark the inuse vectors */
for_each_irq_desc(irq, desc) {
cfg = desc->chip_data;
if (!cpumask_test_cpu(cpu, cfg->domain))
continue;
vector = cfg->vector;
per_cpu(vector_irq, cpu)[vector] = irq;
}
/* Mark the free vectors */
for (vector = 0; vector < NR_VECTORS; ++vector) {
irq = per_cpu(vector_irq, cpu)[vector];
if (irq < 0)
continue;
cfg = irq_cfg(irq);
if (!cpumask_test_cpu(cpu, cfg->domain))
per_cpu(vector_irq, cpu)[vector] = -1;
}
}
static struct irq_chip ioapic_chip;
static struct irq_chip ir_ioapic_chip;
#define IOAPIC_AUTO -1
#define IOAPIC_EDGE 0
#define IOAPIC_LEVEL 1
#ifdef CONFIG_X86_32
static inline int IO_APIC_irq_trigger(int irq)
{
int apic, idx, pin;
for (apic = 0; apic < nr_ioapics; apic++) {
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++) {
idx = find_irq_entry(apic, pin, mp_INT);
if ((idx != -1) && (irq == pin_2_irq(idx, apic, pin)))
return irq_trigger(idx);
}
}
/*
* nonexistent IRQs are edge default
*/
return 0;
}
#else
static inline int IO_APIC_irq_trigger(int irq)
{
return 1;
}
#endif
static void ioapic_register_intr(int irq, struct irq_desc *desc, unsigned long trigger)
{
if ((trigger == IOAPIC_AUTO && IO_APIC_irq_trigger(irq)) ||
trigger == IOAPIC_LEVEL)
desc->status |= IRQ_LEVEL;
else
desc->status &= ~IRQ_LEVEL;
if (irq_remapped(irq)) {
desc->status |= IRQ_MOVE_PCNTXT;
if (trigger)
set_irq_chip_and_handler_name(irq, &ir_ioapic_chip,
handle_fasteoi_irq,
"fasteoi");
else
set_irq_chip_and_handler_name(irq, &ir_ioapic_chip,
handle_edge_irq, "edge");
return;
}
if ((trigger == IOAPIC_AUTO && IO_APIC_irq_trigger(irq)) ||
trigger == IOAPIC_LEVEL)
set_irq_chip_and_handler_name(irq, &ioapic_chip,
handle_fasteoi_irq,
"fasteoi");
else
set_irq_chip_and_handler_name(irq, &ioapic_chip,
handle_edge_irq, "edge");
}
int setup_ioapic_entry(int apic_id, int irq,
struct IO_APIC_route_entry *entry,
unsigned int destination, int trigger,
int polarity, int vector, int pin)
{
/*
* add it to the IO-APIC irq-routing table:
*/
memset(entry,0,sizeof(*entry));
if (intr_remapping_enabled) {
struct intel_iommu *iommu = map_ioapic_to_ir(apic_id);
struct irte irte;
struct IR_IO_APIC_route_entry *ir_entry =
(struct IR_IO_APIC_route_entry *) entry;
int index;
if (!iommu)
panic("No mapping iommu for ioapic %d\n", apic_id);
index = alloc_irte(iommu, irq, 1);
if (index < 0)
panic("Failed to allocate IRTE for ioapic %d\n", apic_id);
memset(&irte, 0, sizeof(irte));
irte.present = 1;
irte.dst_mode = apic->irq_dest_mode;
/*
* Trigger mode in the IRTE will always be edge, and the
* actual level or edge trigger will be setup in the IO-APIC
* RTE. This will help simplify level triggered irq migration.
* For more details, see the comments above explainig IO-APIC
* irq migration in the presence of interrupt-remapping.
*/
irte.trigger_mode = 0;
irte.dlvry_mode = apic->irq_delivery_mode;
irte.vector = vector;
irte.dest_id = IRTE_DEST(destination);
/* Set source-id of interrupt request */
set_ioapic_sid(&irte, apic_id);
modify_irte(irq, &irte);
ir_entry->index2 = (index >> 15) & 0x1;
ir_entry->zero = 0;
ir_entry->format = 1;
ir_entry->index = (index & 0x7fff);
/*
* IO-APIC RTE will be configured with virtual vector.
* irq handler will do the explicit EOI to the io-apic.
*/
ir_entry->vector = pin;
} else {
entry->delivery_mode = apic->irq_delivery_mode;
entry->dest_mode = apic->irq_dest_mode;
entry->dest = destination;
entry->vector = vector;
}
entry->mask = 0; /* enable IRQ */
entry->trigger = trigger;
entry->polarity = polarity;
/* Mask level triggered irqs.
* Use IRQ_DELAYED_DISABLE for edge triggered irqs.
*/
if (trigger)
entry->mask = 1;
return 0;
}
static void setup_IO_APIC_irq(int apic_id, int pin, unsigned int irq, struct irq_desc *desc,
int trigger, int polarity)
{
struct irq_cfg *cfg;
struct IO_APIC_route_entry entry;
unsigned int dest;
if (!IO_APIC_IRQ(irq))
return;
cfg = desc->chip_data;
if (assign_irq_vector(irq, cfg, apic->target_cpus()))
return;
dest = apic->cpu_mask_to_apicid_and(cfg->domain, apic->target_cpus());
apic_printk(APIC_VERBOSE,KERN_DEBUG
"IOAPIC[%d]: Set routing entry (%d-%d -> 0x%x -> "
"IRQ %d Mode:%i Active:%i)\n",
apic_id, mp_ioapics[apic_id].apicid, pin, cfg->vector,
irq, trigger, polarity);
if (setup_ioapic_entry(mp_ioapics[apic_id].apicid, irq, &entry,
dest, trigger, polarity, cfg->vector, pin)) {
printk("Failed to setup ioapic entry for ioapic %d, pin %d\n",
mp_ioapics[apic_id].apicid, pin);
__clear_irq_vector(irq, cfg);
return;
}
ioapic_register_intr(irq, desc, trigger);
if (irq < nr_legacy_irqs)
disable_8259A_irq(irq);
ioapic_write_entry(apic_id, pin, entry);
}
static struct {
DECLARE_BITMAP(pin_programmed, MP_MAX_IOAPIC_PIN + 1);
} mp_ioapic_routing[MAX_IO_APICS];
static void __init setup_IO_APIC_irqs(void)
{
int apic_id = 0, pin, idx, irq;
int notcon = 0;
struct irq_desc *desc;
struct irq_cfg *cfg;
int node = cpu_to_node(boot_cpu_id);
apic_printk(APIC_VERBOSE, KERN_DEBUG "init IO_APIC IRQs\n");
#ifdef CONFIG_ACPI
if (!acpi_disabled && acpi_ioapic) {
apic_id = mp_find_ioapic(0);
if (apic_id < 0)
apic_id = 0;
}
#endif
for (pin = 0; pin < nr_ioapic_registers[apic_id]; pin++) {
idx = find_irq_entry(apic_id, pin, mp_INT);
if (idx == -1) {
if (!notcon) {
notcon = 1;
apic_printk(APIC_VERBOSE,
KERN_DEBUG " %d-%d",
mp_ioapics[apic_id].apicid, pin);
} else
apic_printk(APIC_VERBOSE, " %d-%d",
mp_ioapics[apic_id].apicid, pin);
continue;
}
if (notcon) {
apic_printk(APIC_VERBOSE,
" (apicid-pin) not connected\n");
notcon = 0;
}
irq = pin_2_irq(idx, apic_id, pin);
/*
* Skip the timer IRQ if there's a quirk handler
* installed and if it returns 1:
*/
if (apic->multi_timer_check &&
apic->multi_timer_check(apic_id, irq))
continue;
desc = irq_to_desc_alloc_node(irq, node);
if (!desc) {
printk(KERN_INFO "can not get irq_desc for %d\n", irq);
continue;
}
cfg = desc->chip_data;
add_pin_to_irq_node(cfg, node, apic_id, pin);
/*
* don't mark it in pin_programmed, so later acpi could
* set it correctly when irq < 16
*/
setup_IO_APIC_irq(apic_id, pin, irq, desc,
irq_trigger(idx), irq_polarity(idx));
}
if (notcon)
apic_printk(APIC_VERBOSE,
" (apicid-pin) not connected\n");
}
/*
* Set up the timer pin, possibly with the 8259A-master behind.
*/
static void __init setup_timer_IRQ0_pin(unsigned int apic_id, unsigned int pin,
int vector)
{
struct IO_APIC_route_entry entry;
if (intr_remapping_enabled)
return;
memset(&entry, 0, sizeof(entry));
/*
* We use logical delivery to get the timer IRQ
* to the first CPU.
*/
entry.dest_mode = apic->irq_dest_mode;
entry.mask = 0; /* don't mask IRQ for edge */
entry.dest = apic->cpu_mask_to_apicid(apic->target_cpus());
entry.delivery_mode = apic->irq_delivery_mode;
entry.polarity = 0;
entry.trigger = 0;
entry.vector = vector;
/*
* The timer IRQ doesn't have to know that behind the
* scene we may have a 8259A-master in AEOI mode ...
*/
set_irq_chip_and_handler_name(0, &ioapic_chip, handle_edge_irq, "edge");
/*
* Add it to the IO-APIC irq-routing table:
*/
ioapic_write_entry(apic_id, pin, entry);
}
__apicdebuginit(void) print_IO_APIC(void)
{
int apic, i;
union IO_APIC_reg_00 reg_00;
union IO_APIC_reg_01 reg_01;
union IO_APIC_reg_02 reg_02;
union IO_APIC_reg_03 reg_03;
unsigned long flags;
struct irq_cfg *cfg;
struct irq_desc *desc;
unsigned int irq;
printk(KERN_DEBUG "number of MP IRQ sources: %d.\n", mp_irq_entries);
for (i = 0; i < nr_ioapics; i++)
printk(KERN_DEBUG "number of IO-APIC #%d registers: %d.\n",
mp_ioapics[i].apicid, nr_ioapic_registers[i]);
/*
* We are a bit conservative about what we expect. We have to
* know about every hardware change ASAP.
*/
printk(KERN_INFO "testing the IO APIC.......................\n");
for (apic = 0; apic < nr_ioapics; apic++) {
spin_lock_irqsave(&ioapic_lock, flags);
reg_00.raw = io_apic_read(apic, 0);
reg_01.raw = io_apic_read(apic, 1);
if (reg_01.bits.version >= 0x10)
reg_02.raw = io_apic_read(apic, 2);
if (reg_01.bits.version >= 0x20)
reg_03.raw = io_apic_read(apic, 3);
spin_unlock_irqrestore(&ioapic_lock, flags);
printk("\n");
printk(KERN_DEBUG "IO APIC #%d......\n", mp_ioapics[apic].apicid);
printk(KERN_DEBUG ".... register #00: %08X\n", reg_00.raw);
printk(KERN_DEBUG "....... : physical APIC id: %02X\n", reg_00.bits.ID);
printk(KERN_DEBUG "....... : Delivery Type: %X\n", reg_00.bits.delivery_type);
printk(KERN_DEBUG "....... : LTS : %X\n", reg_00.bits.LTS);
printk(KERN_DEBUG ".... register #01: %08X\n", *(int *)&reg_01);
printk(KERN_DEBUG "....... : max redirection entries: %04X\n", reg_01.bits.entries);
printk(KERN_DEBUG "....... : PRQ implemented: %X\n", reg_01.bits.PRQ);
printk(KERN_DEBUG "....... : IO APIC version: %04X\n", reg_01.bits.version);
/*
* Some Intel chipsets with IO APIC VERSION of 0x1? don't have reg_02,
* but the value of reg_02 is read as the previous read register
* value, so ignore it if reg_02 == reg_01.
*/
if (reg_01.bits.version >= 0x10 && reg_02.raw != reg_01.raw) {
printk(KERN_DEBUG ".... register #02: %08X\n", reg_02.raw);
printk(KERN_DEBUG "....... : arbitration: %02X\n", reg_02.bits.arbitration);
}
/*
* Some Intel chipsets with IO APIC VERSION of 0x2? don't have reg_02
* or reg_03, but the value of reg_0[23] is read as the previous read
* register value, so ignore it if reg_03 == reg_0[12].
*/
if (reg_01.bits.version >= 0x20 && reg_03.raw != reg_02.raw &&
reg_03.raw != reg_01.raw) {
printk(KERN_DEBUG ".... register #03: %08X\n", reg_03.raw);
printk(KERN_DEBUG "....... : Boot DT : %X\n", reg_03.bits.boot_DT);
}
printk(KERN_DEBUG ".... IRQ redirection table:\n");
printk(KERN_DEBUG " NR Dst Mask Trig IRR Pol"
" Stat Dmod Deli Vect: \n");
for (i = 0; i <= reg_01.bits.entries; i++) {
struct IO_APIC_route_entry entry;
entry = ioapic_read_entry(apic, i);
printk(KERN_DEBUG " %02x %03X ",
i,
entry.dest
);
printk("%1d %1d %1d %1d %1d %1d %1d %02X\n",
entry.mask,
entry.trigger,
entry.irr,
entry.polarity,
entry.delivery_status,
entry.dest_mode,
entry.delivery_mode,
entry.vector
);
}
}
printk(KERN_DEBUG "IRQ to pin mappings:\n");
for_each_irq_desc(irq, desc) {
struct irq_pin_list *entry;
cfg = desc->chip_data;
entry = cfg->irq_2_pin;
if (!entry)
continue;
printk(KERN_DEBUG "IRQ%d ", irq);
for_each_irq_pin(entry, cfg->irq_2_pin)
printk("-> %d:%d", entry->apic, entry->pin);
printk("\n");
}
printk(KERN_INFO ".................................... done.\n");
return;
}
__apicdebuginit(void) print_APIC_field(int base)
{
int i;
printk(KERN_DEBUG);
for (i = 0; i < 8; i++)
printk(KERN_CONT "%08x", apic_read(base + i*0x10));
printk(KERN_CONT "\n");
}
__apicdebuginit(void) print_local_APIC(void *dummy)
{
unsigned int i, v, ver, maxlvt;
u64 icr;
printk(KERN_DEBUG "printing local APIC contents on CPU#%d/%d:\n",
smp_processor_id(), hard_smp_processor_id());
v = apic_read(APIC_ID);
printk(KERN_INFO "... APIC ID: %08x (%01x)\n", v, read_apic_id());
v = apic_read(APIC_LVR);
printk(KERN_INFO "... APIC VERSION: %08x\n", v);
ver = GET_APIC_VERSION(v);
maxlvt = lapic_get_maxlvt();
v = apic_read(APIC_TASKPRI);
printk(KERN_DEBUG "... APIC TASKPRI: %08x (%02x)\n", v, v & APIC_TPRI_MASK);
if (APIC_INTEGRATED(ver)) { /* !82489DX */
if (!APIC_XAPIC(ver)) {
v = apic_read(APIC_ARBPRI);
printk(KERN_DEBUG "... APIC ARBPRI: %08x (%02x)\n", v,
v & APIC_ARBPRI_MASK);
}
v = apic_read(APIC_PROCPRI);
printk(KERN_DEBUG "... APIC PROCPRI: %08x\n", v);
}
/*
* Remote read supported only in the 82489DX and local APIC for
* Pentium processors.
*/
if (!APIC_INTEGRATED(ver) || maxlvt == 3) {
v = apic_read(APIC_RRR);
printk(KERN_DEBUG "... APIC RRR: %08x\n", v);
}
v = apic_read(APIC_LDR);
printk(KERN_DEBUG "... APIC LDR: %08x\n", v);
if (!x2apic_enabled()) {
v = apic_read(APIC_DFR);
printk(KERN_DEBUG "... APIC DFR: %08x\n", v);
}
v = apic_read(APIC_SPIV);
printk(KERN_DEBUG "... APIC SPIV: %08x\n", v);
printk(KERN_DEBUG "... APIC ISR field:\n");
print_APIC_field(APIC_ISR);
printk(KERN_DEBUG "... APIC TMR field:\n");
print_APIC_field(APIC_TMR);
printk(KERN_DEBUG "... APIC IRR field:\n");
print_APIC_field(APIC_IRR);
if (APIC_INTEGRATED(ver)) { /* !82489DX */
if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
apic_write(APIC_ESR, 0);
v = apic_read(APIC_ESR);
printk(KERN_DEBUG "... APIC ESR: %08x\n", v);
}
icr = apic_icr_read();
printk(KERN_DEBUG "... APIC ICR: %08x\n", (u32)icr);
printk(KERN_DEBUG "... APIC ICR2: %08x\n", (u32)(icr >> 32));
v = apic_read(APIC_LVTT);
printk(KERN_DEBUG "... APIC LVTT: %08x\n", v);
if (maxlvt > 3) { /* PC is LVT#4. */
v = apic_read(APIC_LVTPC);
printk(KERN_DEBUG "... APIC LVTPC: %08x\n", v);
}
v = apic_read(APIC_LVT0);
printk(KERN_DEBUG "... APIC LVT0: %08x\n", v);
v = apic_read(APIC_LVT1);
printk(KERN_DEBUG "... APIC LVT1: %08x\n", v);
if (maxlvt > 2) { /* ERR is LVT#3. */
v = apic_read(APIC_LVTERR);
printk(KERN_DEBUG "... APIC LVTERR: %08x\n", v);
}
v = apic_read(APIC_TMICT);
printk(KERN_DEBUG "... APIC TMICT: %08x\n", v);
v = apic_read(APIC_TMCCT);
printk(KERN_DEBUG "... APIC TMCCT: %08x\n", v);
v = apic_read(APIC_TDCR);
printk(KERN_DEBUG "... APIC TDCR: %08x\n", v);
if (boot_cpu_has(X86_FEATURE_EXTAPIC)) {
v = apic_read(APIC_EFEAT);
maxlvt = (v >> 16) & 0xff;
printk(KERN_DEBUG "... APIC EFEAT: %08x\n", v);
v = apic_read(APIC_ECTRL);
printk(KERN_DEBUG "... APIC ECTRL: %08x\n", v);
for (i = 0; i < maxlvt; i++) {
v = apic_read(APIC_EILVTn(i));
printk(KERN_DEBUG "... APIC EILVT%d: %08x\n", i, v);
}
}
printk("\n");
}
__apicdebuginit(void) print_local_APICs(int maxcpu)
{
int cpu;
if (!maxcpu)
return;
preempt_disable();
for_each_online_cpu(cpu) {
if (cpu >= maxcpu)
break;
smp_call_function_single(cpu, print_local_APIC, NULL, 1);
}
preempt_enable();
}
__apicdebuginit(void) print_PIC(void)
{
unsigned int v;
unsigned long flags;
if (!nr_legacy_irqs)
return;
printk(KERN_DEBUG "\nprinting PIC contents\n");
spin_lock_irqsave(&i8259A_lock, flags);
v = inb(0xa1) << 8 | inb(0x21);
printk(KERN_DEBUG "... PIC IMR: %04x\n", v);
v = inb(0xa0) << 8 | inb(0x20);
printk(KERN_DEBUG "... PIC IRR: %04x\n", v);
outb(0x0b,0xa0);
outb(0x0b,0x20);
v = inb(0xa0) << 8 | inb(0x20);
outb(0x0a,0xa0);
outb(0x0a,0x20);
spin_unlock_irqrestore(&i8259A_lock, flags);
printk(KERN_DEBUG "... PIC ISR: %04x\n", v);
v = inb(0x4d1) << 8 | inb(0x4d0);
printk(KERN_DEBUG "... PIC ELCR: %04x\n", v);
}
static int __initdata show_lapic = 1;
static __init int setup_show_lapic(char *arg)
{
int num = -1;
if (strcmp(arg, "all") == 0) {
show_lapic = CONFIG_NR_CPUS;
} else {
get_option(&arg, &num);
if (num >= 0)
show_lapic = num;
}
return 1;
}
__setup("show_lapic=", setup_show_lapic);
__apicdebuginit(int) print_ICs(void)
{
if (apic_verbosity == APIC_QUIET)
return 0;
print_PIC();
/* don't print out if apic is not there */
if (!cpu_has_apic && !apic_from_smp_config())
return 0;
print_local_APICs(show_lapic);
print_IO_APIC();
return 0;
}
fs_initcall(print_ICs);
/* Where if anywhere is the i8259 connect in external int mode */
static struct { int pin, apic; } ioapic_i8259 = { -1, -1 };
void __init enable_IO_APIC(void)
{
union IO_APIC_reg_01 reg_01;
int i8259_apic, i8259_pin;
int apic;
unsigned long flags;
/*
* The number of IO-APIC IRQ registers (== #pins):
*/
for (apic = 0; apic < nr_ioapics; apic++) {
spin_lock_irqsave(&ioapic_lock, flags);
reg_01.raw = io_apic_read(apic, 1);
spin_unlock_irqrestore(&ioapic_lock, flags);
nr_ioapic_registers[apic] = reg_01.bits.entries+1;
}
if (!nr_legacy_irqs)
return;
for(apic = 0; apic < nr_ioapics; apic++) {
int pin;
/* See if any of the pins is in ExtINT mode */
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++) {
struct IO_APIC_route_entry entry;
entry = ioapic_read_entry(apic, pin);
/* If the interrupt line is enabled and in ExtInt mode
* I have found the pin where the i8259 is connected.
*/
if ((entry.mask == 0) && (entry.delivery_mode == dest_ExtINT)) {
ioapic_i8259.apic = apic;
ioapic_i8259.pin = pin;
goto found_i8259;
}
}
}
found_i8259:
/* Look to see what if the MP table has reported the ExtINT */
/* If we could not find the appropriate pin by looking at the ioapic
* the i8259 probably is not connected the ioapic but give the
* mptable a chance anyway.
*/
i8259_pin = find_isa_irq_pin(0, mp_ExtINT);
i8259_apic = find_isa_irq_apic(0, mp_ExtINT);
/* Trust the MP table if nothing is setup in the hardware */
if ((ioapic_i8259.pin == -1) && (i8259_pin >= 0)) {
printk(KERN_WARNING "ExtINT not setup in hardware but reported by MP table\n");
ioapic_i8259.pin = i8259_pin;
ioapic_i8259.apic = i8259_apic;
}
/* Complain if the MP table and the hardware disagree */
if (((ioapic_i8259.apic != i8259_apic) || (ioapic_i8259.pin != i8259_pin)) &&
(i8259_pin >= 0) && (ioapic_i8259.pin >= 0))
{
printk(KERN_WARNING "ExtINT in hardware and MP table differ\n");
}
/*
* Do not trust the IO-APIC being empty at bootup
*/
clear_IO_APIC();
}
/*
* Not an __init, needed by the reboot code
*/
void disable_IO_APIC(void)
{
/*
* Clear the IO-APIC before rebooting:
*/
clear_IO_APIC();
if (!nr_legacy_irqs)
return;
/*
* If the i8259 is routed through an IOAPIC
* Put that IOAPIC in virtual wire mode
* so legacy interrupts can be delivered.
*
* With interrupt-remapping, for now we will use virtual wire A mode,
* as virtual wire B is little complex (need to configure both
* IOAPIC RTE aswell as interrupt-remapping table entry).
* As this gets called during crash dump, keep this simple for now.
*/
if (ioapic_i8259.pin != -1 && !intr_remapping_enabled) {
struct IO_APIC_route_entry entry;
memset(&entry, 0, sizeof(entry));
entry.mask = 0; /* Enabled */
entry.trigger = 0; /* Edge */
entry.irr = 0;
entry.polarity = 0; /* High */
entry.delivery_status = 0;
entry.dest_mode = 0; /* Physical */
entry.delivery_mode = dest_ExtINT; /* ExtInt */
entry.vector = 0;
entry.dest = read_apic_id();
/*
* Add it to the IO-APIC irq-routing table:
*/
ioapic_write_entry(ioapic_i8259.apic, ioapic_i8259.pin, entry);
}
/*
* Use virtual wire A mode when interrupt remapping is enabled.
*/
if (cpu_has_apic || apic_from_smp_config())
disconnect_bsp_APIC(!intr_remapping_enabled &&
ioapic_i8259.pin != -1);
}
#ifdef CONFIG_X86_32
/*
* function to set the IO-APIC physical IDs based on the
* values stored in the MPC table.
*
* by Matt Domsch <Matt_Domsch@dell.com> Tue Dec 21 12:25:05 CST 1999
*/
void __init setup_ioapic_ids_from_mpc(void)
{
union IO_APIC_reg_00 reg_00;
physid_mask_t phys_id_present_map;
int apic_id;
int i;
unsigned char old_id;
unsigned long flags;
if (acpi_ioapic)
return;
/*
* Don't check I/O APIC IDs for xAPIC systems. They have
* no meaning without the serial APIC bus.
*/
if (!(boot_cpu_data.x86_vendor == X86_VENDOR_INTEL)
|| APIC_XAPIC(apic_version[boot_cpu_physical_apicid]))
return;
/*
* This is broken; anything with a real cpu count has to
* circumvent this idiocy regardless.
*/
phys_id_present_map = apic->ioapic_phys_id_map(phys_cpu_present_map);
/*
* Set the IOAPIC ID to the value stored in the MPC table.
*/
for (apic_id = 0; apic_id < nr_ioapics; apic_id++) {
/* Read the register 0 value */
spin_lock_irqsave(&ioapic_lock, flags);
reg_00.raw = io_apic_read(apic_id, 0);
spin_unlock_irqrestore(&ioapic_lock, flags);
old_id = mp_ioapics[apic_id].apicid;
if (mp_ioapics[apic_id].apicid >= get_physical_broadcast()) {
printk(KERN_ERR "BIOS bug, IO-APIC#%d ID is %d in the MPC table!...\n",
apic_id, mp_ioapics[apic_id].apicid);
printk(KERN_ERR "... fixing up to %d. (tell your hw vendor)\n",
reg_00.bits.ID);
mp_ioapics[apic_id].apicid = reg_00.bits.ID;
}
/*
* Sanity check, is the ID really free? Every APIC in a
* system must have a unique ID or we get lots of nice
* 'stuck on smp_invalidate_needed IPI wait' messages.
*/
if (apic->check_apicid_used(phys_id_present_map,
mp_ioapics[apic_id].apicid)) {
printk(KERN_ERR "BIOS bug, IO-APIC#%d ID %d is already used!...\n",
apic_id, mp_ioapics[apic_id].apicid);
for (i = 0; i < get_physical_broadcast(); i++)
if (!physid_isset(i, phys_id_present_map))
break;
if (i >= get_physical_broadcast())
panic("Max APIC ID exceeded!\n");
printk(KERN_ERR "... fixing up to %d. (tell your hw vendor)\n",
i);
physid_set(i, phys_id_present_map);
mp_ioapics[apic_id].apicid = i;
} else {
physid_mask_t tmp;
tmp = apic->apicid_to_cpu_present(mp_ioapics[apic_id].apicid);
apic_printk(APIC_VERBOSE, "Setting %d in the "
"phys_id_present_map\n",
mp_ioapics[apic_id].apicid);
physids_or(phys_id_present_map, phys_id_present_map, tmp);
}
/*
* We need to adjust the IRQ routing table
* if the ID changed.
*/
if (old_id != mp_ioapics[apic_id].apicid)
for (i = 0; i < mp_irq_entries; i++)
if (mp_irqs[i].dstapic == old_id)
mp_irqs[i].dstapic
= mp_ioapics[apic_id].apicid;
/*
* Read the right value from the MPC table and
* write it into the ID register.
*/
apic_printk(APIC_VERBOSE, KERN_INFO
"...changing IO-APIC physical APIC ID to %d ...",
mp_ioapics[apic_id].apicid);
reg_00.bits.ID = mp_ioapics[apic_id].apicid;
spin_lock_irqsave(&ioapic_lock, flags);
io_apic_write(apic_id, 0, reg_00.raw);
spin_unlock_irqrestore(&ioapic_lock, flags);
/*
* Sanity check
*/
spin_lock_irqsave(&ioapic_lock, flags);
reg_00.raw = io_apic_read(apic_id, 0);
spin_unlock_irqrestore(&ioapic_lock, flags);
if (reg_00.bits.ID != mp_ioapics[apic_id].apicid)
printk("could not set ID!\n");
else
apic_printk(APIC_VERBOSE, " ok.\n");
}
}
#endif
int no_timer_check __initdata;
static int __init notimercheck(char *s)
{
no_timer_check = 1;
return 1;
}
__setup("no_timer_check", notimercheck);
/*
* There is a nasty bug in some older SMP boards, their mptable lies
* about the timer IRQ. We do the following to work around the situation:
*
* - timer IRQ defaults to IO-APIC IRQ
* - if this function detects that timer IRQs are defunct, then we fall
* back to ISA timer IRQs
*/
static int __init timer_irq_works(void)
{
unsigned long t1 = jiffies;
unsigned long flags;
if (no_timer_check)
return 1;
local_save_flags(flags);
local_irq_enable();
/* Let ten ticks pass... */
mdelay((10 * 1000) / HZ);
local_irq_restore(flags);
/*
* Expect a few ticks at least, to be sure some possible
* glue logic does not lock up after one or two first
* ticks in a non-ExtINT mode. Also the local APIC
* might have cached one ExtINT interrupt. Finally, at
* least one tick may be lost due to delays.
*/
/* jiffies wrap? */
if (time_after(jiffies, t1 + 4))
return 1;
return 0;
}
/*
* In the SMP+IOAPIC case it might happen that there are an unspecified
* number of pending IRQ events unhandled. These cases are very rare,
* so we 'resend' these IRQs via IPIs, to the same CPU. It's much
* better to do it this way as thus we do not have to be aware of
* 'pending' interrupts in the IRQ path, except at this point.
*/
/*
* Edge triggered needs to resend any interrupt
* that was delayed but this is now handled in the device
* independent code.
*/
/*
* Starting up a edge-triggered IO-APIC interrupt is
* nasty - we need to make sure that we get the edge.
* If it is already asserted for some reason, we need
* return 1 to indicate that is was pending.
*
* This is not complete - we should be able to fake
* an edge even if it isn't on the 8259A...
*/
static unsigned int startup_ioapic_irq(unsigned int irq)
{
int was_pending = 0;
unsigned long flags;
struct irq_cfg *cfg;
spin_lock_irqsave(&ioapic_lock, flags);
if (irq < nr_legacy_irqs) {
disable_8259A_irq(irq);
if (i8259A_irq_pending(irq))
was_pending = 1;
}
cfg = irq_cfg(irq);
__unmask_IO_APIC_irq(cfg);
spin_unlock_irqrestore(&ioapic_lock, flags);
return was_pending;
}
static int ioapic_retrigger_irq(unsigned int irq)
{
struct irq_cfg *cfg = irq_cfg(irq);
unsigned long flags;
spin_lock_irqsave(&vector_lock, flags);
apic->send_IPI_mask(cpumask_of(cpumask_first(cfg->domain)), cfg->vector);
spin_unlock_irqrestore(&vector_lock, flags);
return 1;
}
/*
* Level and edge triggered IO-APIC interrupts need different handling,
* so we use two separate IRQ descriptors. Edge triggered IRQs can be
* handled with the level-triggered descriptor, but that one has slightly
* more overhead. Level-triggered interrupts cannot be handled with the
* edge-triggered handler, without risking IRQ storms and other ugly
* races.
*/
#ifdef CONFIG_SMP
void send_cleanup_vector(struct irq_cfg *cfg)
{
cpumask_var_t cleanup_mask;
if (unlikely(!alloc_cpumask_var(&cleanup_mask, GFP_ATOMIC))) {
unsigned int i;
for_each_cpu_and(i, cfg->old_domain, cpu_online_mask)
apic->send_IPI_mask(cpumask_of(i), IRQ_MOVE_CLEANUP_VECTOR);
} else {
cpumask_and(cleanup_mask, cfg->old_domain, cpu_online_mask);
apic->send_IPI_mask(cleanup_mask, IRQ_MOVE_CLEANUP_VECTOR);
free_cpumask_var(cleanup_mask);
}
cfg->move_in_progress = 0;
}
static void __target_IO_APIC_irq(unsigned int irq, unsigned int dest, struct irq_cfg *cfg)
{
int apic, pin;
struct irq_pin_list *entry;
u8 vector = cfg->vector;
for_each_irq_pin(entry, cfg->irq_2_pin) {
unsigned int reg;
apic = entry->apic;
pin = entry->pin;
/*
* With interrupt-remapping, destination information comes
* from interrupt-remapping table entry.
*/
if (!irq_remapped(irq))
io_apic_write(apic, 0x11 + pin*2, dest);
reg = io_apic_read(apic, 0x10 + pin*2);
reg &= ~IO_APIC_REDIR_VECTOR_MASK;
reg |= vector;
io_apic_modify(apic, 0x10 + pin*2, reg);
}
}
/*
* Either sets desc->affinity to a valid value, and returns
* ->cpu_mask_to_apicid of that, or returns BAD_APICID and
* leaves desc->affinity untouched.
*/
unsigned int
set_desc_affinity(struct irq_desc *desc, const struct cpumask *mask)
{
struct irq_cfg *cfg;
unsigned int irq;
if (!cpumask_intersects(mask, cpu_online_mask))
return BAD_APICID;
irq = desc->irq;
cfg = desc->chip_data;
if (assign_irq_vector(irq, cfg, mask))
return BAD_APICID;
cpumask_copy(desc->affinity, mask);
return apic->cpu_mask_to_apicid_and(desc->affinity, cfg->domain);
}
static int
set_ioapic_affinity_irq_desc(struct irq_desc *desc, const struct cpumask *mask)
{
struct irq_cfg *cfg;
unsigned long flags;
unsigned int dest;
unsigned int irq;
int ret = -1;
irq = desc->irq;
cfg = desc->chip_data;
spin_lock_irqsave(&ioapic_lock, flags);
dest = set_desc_affinity(desc, mask);
if (dest != BAD_APICID) {
/* Only the high 8 bits are valid. */
dest = SET_APIC_LOGICAL_ID(dest);
__target_IO_APIC_irq(irq, dest, cfg);
ret = 0;
}
spin_unlock_irqrestore(&ioapic_lock, flags);
return ret;
}
static int
set_ioapic_affinity_irq(unsigned int irq, const struct cpumask *mask)
{
struct irq_desc *desc;
desc = irq_to_desc(irq);
return set_ioapic_affinity_irq_desc(desc, mask);
}
#ifdef CONFIG_INTR_REMAP
/*
* Migrate the IO-APIC irq in the presence of intr-remapping.
*
* For both level and edge triggered, irq migration is a simple atomic
* update(of vector and cpu destination) of IRTE and flush the hardware cache.
*
* For level triggered, we eliminate the io-apic RTE modification (with the
* updated vector information), by using a virtual vector (io-apic pin number).
* Real vector that is used for interrupting cpu will be coming from
* the interrupt-remapping table entry.
*/
static int
migrate_ioapic_irq_desc(struct irq_desc *desc, const struct cpumask *mask)
{
struct irq_cfg *cfg;
struct irte irte;
unsigned int dest;
unsigned int irq;
int ret = -1;
if (!cpumask_intersects(mask, cpu_online_mask))
return ret;
irq = desc->irq;
if (get_irte(irq, &irte))
return ret;
cfg = desc->chip_data;
if (assign_irq_vector(irq, cfg, mask))
return ret;
dest = apic->cpu_mask_to_apicid_and(cfg->domain, mask);
irte.vector = cfg->vector;
irte.dest_id = IRTE_DEST(dest);
/*
* Modified the IRTE and flushes the Interrupt entry cache.
*/
modify_irte(irq, &irte);
if (cfg->move_in_progress)
send_cleanup_vector(cfg);
cpumask_copy(desc->affinity, mask);
return 0;
}
/*
* Migrates the IRQ destination in the process context.
*/
static int set_ir_ioapic_affinity_irq_desc(struct irq_desc *desc,
const struct cpumask *mask)
{
return migrate_ioapic_irq_desc(desc, mask);
}
static int set_ir_ioapic_affinity_irq(unsigned int irq,
const struct cpumask *mask)
{
struct irq_desc *desc = irq_to_desc(irq);
return set_ir_ioapic_affinity_irq_desc(desc, mask);
}
#else
static inline int set_ir_ioapic_affinity_irq_desc(struct irq_desc *desc,
const struct cpumask *mask)
{
return 0;
}
#endif
asmlinkage void smp_irq_move_cleanup_interrupt(void)
{
unsigned vector, me;
ack_APIC_irq();
exit_idle();
irq_enter();
me = smp_processor_id();
for (vector = FIRST_EXTERNAL_VECTOR; vector < NR_VECTORS; vector++) {
unsigned int irq;
unsigned int irr;
struct irq_desc *desc;
struct irq_cfg *cfg;
irq = __get_cpu_var(vector_irq)[vector];
if (irq == -1)
continue;
desc = irq_to_desc(irq);
if (!desc)
continue;
cfg = irq_cfg(irq);
spin_lock(&desc->lock);
if (vector == cfg->vector && cpumask_test_cpu(me, cfg->domain))
goto unlock;
irr = apic_read(APIC_IRR + (vector / 32 * 0x10));
/*
* Check if the vector that needs to be cleanedup is
* registered at the cpu's IRR. If so, then this is not
* the best time to clean it up. Lets clean it up in the
* next attempt by sending another IRQ_MOVE_CLEANUP_VECTOR
* to myself.
*/
if (irr & (1 << (vector % 32))) {
apic->send_IPI_self(IRQ_MOVE_CLEANUP_VECTOR);
goto unlock;
}
__get_cpu_var(vector_irq)[vector] = -1;
unlock:
spin_unlock(&desc->lock);
}
irq_exit();
}
static void __irq_complete_move(struct irq_desc **descp, unsigned vector)
{
struct irq_desc *desc = *descp;
struct irq_cfg *cfg = desc->chip_data;
unsigned me;
if (likely(!cfg->move_in_progress))
return;
me = smp_processor_id();
if (vector == cfg->vector && cpumask_test_cpu(me, cfg->domain))
send_cleanup_vector(cfg);
}
static void irq_complete_move(struct irq_desc **descp)
{
__irq_complete_move(descp, ~get_irq_regs()->orig_ax);
}
void irq_force_complete_move(int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irq_cfg *cfg = desc->chip_data;
__irq_complete_move(&desc, cfg->vector);
}
#else
static inline void irq_complete_move(struct irq_desc **descp) {}
#endif
static void ack_apic_edge(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
irq_complete_move(&desc);
move_native_irq(irq);
ack_APIC_irq();
}
atomic_t irq_mis_count;
static void ack_apic_level(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
unsigned long v;
int i;
struct irq_cfg *cfg;
int do_unmask_irq = 0;
irq_complete_move(&desc);
#ifdef CONFIG_GENERIC_PENDING_IRQ
/* If we are moving the irq we need to mask it */
if (unlikely(desc->status & IRQ_MOVE_PENDING)) {
do_unmask_irq = 1;
mask_IO_APIC_irq_desc(desc);
}
#endif
/*
* It appears there is an erratum which affects at least version 0x11
* of I/O APIC (that's the 82093AA and cores integrated into various
* chipsets). Under certain conditions a level-triggered interrupt is
* erroneously delivered as edge-triggered one but the respective IRR
* bit gets set nevertheless. As a result the I/O unit expects an EOI
* message but it will never arrive and further interrupts are blocked
* from the source. The exact reason is so far unknown, but the
* phenomenon was observed when two consecutive interrupt requests
* from a given source get delivered to the same CPU and the source is
* temporarily disabled in between.
*
* A workaround is to simulate an EOI message manually. We achieve it
* by setting the trigger mode to edge and then to level when the edge
* trigger mode gets detected in the TMR of a local APIC for a
* level-triggered interrupt. We mask the source for the time of the
* operation to prevent an edge-triggered interrupt escaping meanwhile.
* The idea is from Manfred Spraul. --macro
*/
cfg = desc->chip_data;
i = cfg->vector;
v = apic_read(APIC_TMR + ((i & ~0x1f) >> 1));
/*
* We must acknowledge the irq before we move it or the acknowledge will
* not propagate properly.
*/
ack_APIC_irq();
/* Now we can move and renable the irq */
if (unlikely(do_unmask_irq)) {
/* Only migrate the irq if the ack has been received.
*
* On rare occasions the broadcast level triggered ack gets
* delayed going to ioapics, and if we reprogram the
* vector while Remote IRR is still set the irq will never
* fire again.
*
* To prevent this scenario we read the Remote IRR bit
* of the ioapic. This has two effects.
* - On any sane system the read of the ioapic will
* flush writes (and acks) going to the ioapic from
* this cpu.
* - We get to see if the ACK has actually been delivered.
*
* Based on failed experiments of reprogramming the
* ioapic entry from outside of irq context starting
* with masking the ioapic entry and then polling until
* Remote IRR was clear before reprogramming the
* ioapic I don't trust the Remote IRR bit to be
* completey accurate.
*
* However there appears to be no other way to plug
* this race, so if the Remote IRR bit is not
* accurate and is causing problems then it is a hardware bug
* and you can go talk to the chipset vendor about it.
*/
cfg = desc->chip_data;
if (!io_apic_level_ack_pending(cfg))
move_masked_irq(irq);
unmask_IO_APIC_irq_desc(desc);
}
/* Tail end of version 0x11 I/O APIC bug workaround */
if (!(v & (1 << (i & 0x1f)))) {
atomic_inc(&irq_mis_count);
spin_lock(&ioapic_lock);
__mask_and_edge_IO_APIC_irq(cfg);
__unmask_and_level_IO_APIC_irq(cfg);
spin_unlock(&ioapic_lock);
}
}
#ifdef CONFIG_INTR_REMAP
static void __eoi_ioapic_irq(unsigned int irq, struct irq_cfg *cfg)
{
struct irq_pin_list *entry;
for_each_irq_pin(entry, cfg->irq_2_pin)
io_apic_eoi(entry->apic, entry->pin);
}
static void
eoi_ioapic_irq(struct irq_desc *desc)
{
struct irq_cfg *cfg;
unsigned long flags;
unsigned int irq;
irq = desc->irq;
cfg = desc->chip_data;
spin_lock_irqsave(&ioapic_lock, flags);
__eoi_ioapic_irq(irq, cfg);
spin_unlock_irqrestore(&ioapic_lock, flags);
}
static void ir_ack_apic_edge(unsigned int irq)
{
ack_APIC_irq();
}
static void ir_ack_apic_level(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
ack_APIC_irq();
eoi_ioapic_irq(desc);
}
#endif /* CONFIG_INTR_REMAP */
static struct irq_chip ioapic_chip __read_mostly = {
.name = "IO-APIC",
.startup = startup_ioapic_irq,
.mask = mask_IO_APIC_irq,
.unmask = unmask_IO_APIC_irq,
.ack = ack_apic_edge,
.eoi = ack_apic_level,
#ifdef CONFIG_SMP
.set_affinity = set_ioapic_affinity_irq,
#endif
.retrigger = ioapic_retrigger_irq,
};
static struct irq_chip ir_ioapic_chip __read_mostly = {
.name = "IR-IO-APIC",
.startup = startup_ioapic_irq,
.mask = mask_IO_APIC_irq,
.unmask = unmask_IO_APIC_irq,
#ifdef CONFIG_INTR_REMAP
.ack = ir_ack_apic_edge,
.eoi = ir_ack_apic_level,
#ifdef CONFIG_SMP
.set_affinity = set_ir_ioapic_affinity_irq,
#endif
#endif
.retrigger = ioapic_retrigger_irq,
};
static inline void init_IO_APIC_traps(void)
{
int irq;
struct irq_desc *desc;
struct irq_cfg *cfg;
/*
* NOTE! The local APIC isn't very good at handling
* multiple interrupts at the same interrupt level.
* As the interrupt level is determined by taking the
* vector number and shifting that right by 4, we
* want to spread these out a bit so that they don't
* all fall in the same interrupt level.
*
* Also, we've got to be careful not to trash gate
* 0x80, because int 0x80 is hm, kind of importantish. ;)
*/
for_each_irq_desc(irq, desc) {
cfg = desc->chip_data;
if (IO_APIC_IRQ(irq) && cfg && !cfg->vector) {
/*
* Hmm.. We don't have an entry for this,
* so default to an old-fashioned 8259
* interrupt if we can..
*/
if (irq < nr_legacy_irqs)
make_8259A_irq(irq);
else
/* Strange. Oh, well.. */
desc->chip = &no_irq_chip;
}
}
}
/*
* The local APIC irq-chip implementation:
*/
static void mask_lapic_irq(unsigned int irq)
{
unsigned long v;
v = apic_read(APIC_LVT0);
apic_write(APIC_LVT0, v | APIC_LVT_MASKED);
}
static void unmask_lapic_irq(unsigned int irq)
{
unsigned long v;
v = apic_read(APIC_LVT0);
apic_write(APIC_LVT0, v & ~APIC_LVT_MASKED);
}
static void ack_lapic_irq(unsigned int irq)
{
ack_APIC_irq();
}
static struct irq_chip lapic_chip __read_mostly = {
.name = "local-APIC",
.mask = mask_lapic_irq,
.unmask = unmask_lapic_irq,
.ack = ack_lapic_irq,
};
static void lapic_register_intr(int irq, struct irq_desc *desc)
{
desc->status &= ~IRQ_LEVEL;
set_irq_chip_and_handler_name(irq, &lapic_chip, handle_edge_irq,
"edge");
}
static void __init setup_nmi(void)
{
/*
* Dirty trick to enable the NMI watchdog ...
* We put the 8259A master into AEOI mode and
* unmask on all local APICs LVT0 as NMI.
*
* The idea to use the 8259A in AEOI mode ('8259A Virtual Wire')
* is from Maciej W. Rozycki - so we do not have to EOI from
* the NMI handler or the timer interrupt.
*/
apic_printk(APIC_VERBOSE, KERN_INFO "activating NMI Watchdog ...");
enable_NMI_through_LVT0();
apic_printk(APIC_VERBOSE, " done.\n");
}
/*
* This looks a bit hackish but it's about the only one way of sending
* a few INTA cycles to 8259As and any associated glue logic. ICR does
* not support the ExtINT mode, unfortunately. We need to send these
* cycles as some i82489DX-based boards have glue logic that keeps the
* 8259A interrupt line asserted until INTA. --macro
*/
static inline void __init unlock_ExtINT_logic(void)
{
int apic, pin, i;
struct IO_APIC_route_entry entry0, entry1;
unsigned char save_control, save_freq_select;
pin = find_isa_irq_pin(8, mp_INT);
if (pin == -1) {
WARN_ON_ONCE(1);
return;
}
apic = find_isa_irq_apic(8, mp_INT);
if (apic == -1) {
WARN_ON_ONCE(1);
return;
}
entry0 = ioapic_read_entry(apic, pin);
clear_IO_APIC_pin(apic, pin);
memset(&entry1, 0, sizeof(entry1));
entry1.dest_mode = 0; /* physical delivery */
entry1.mask = 0; /* unmask IRQ now */
entry1.dest = hard_smp_processor_id();
entry1.delivery_mode = dest_ExtINT;
entry1.polarity = entry0.polarity;
entry1.trigger = 0;
entry1.vector = 0;
ioapic_write_entry(apic, pin, entry1);
save_control = CMOS_READ(RTC_CONTROL);
save_freq_select = CMOS_READ(RTC_FREQ_SELECT);
CMOS_WRITE((save_freq_select & ~RTC_RATE_SELECT) | 0x6,
RTC_FREQ_SELECT);
CMOS_WRITE(save_control | RTC_PIE, RTC_CONTROL);
i = 100;
while (i-- > 0) {
mdelay(10);
if ((CMOS_READ(RTC_INTR_FLAGS) & RTC_PF) == RTC_PF)
i -= 10;
}
CMOS_WRITE(save_control, RTC_CONTROL);
CMOS_WRITE(save_freq_select, RTC_FREQ_SELECT);
clear_IO_APIC_pin(apic, pin);
ioapic_write_entry(apic, pin, entry0);
}
static int disable_timer_pin_1 __initdata;
/* Actually the next is obsolete, but keep it for paranoid reasons -AK */
static int __init disable_timer_pin_setup(char *arg)
{
disable_timer_pin_1 = 1;
return 0;
}
early_param("disable_timer_pin_1", disable_timer_pin_setup);
int timer_through_8259 __initdata;
/*
* This code may look a bit paranoid, but it's supposed to cooperate with
* a wide range of boards and BIOS bugs. Fortunately only the timer IRQ
* is so screwy. Thanks to Brian Perkins for testing/hacking this beast
* fanatically on his truly buggy board.
*
* FIXME: really need to revamp this for all platforms.
*/
static inline void __init check_timer(void)
{
struct irq_desc *desc = irq_to_desc(0);
struct irq_cfg *cfg = desc->chip_data;
int node = cpu_to_node(boot_cpu_id);
int apic1, pin1, apic2, pin2;
unsigned long flags;
int no_pin1 = 0;
local_irq_save(flags);
/*
* get/set the timer IRQ vector:
*/
disable_8259A_irq(0);
assign_irq_vector(0, cfg, apic->target_cpus());
/*
* As IRQ0 is to be enabled in the 8259A, the virtual
* wire has to be disabled in the local APIC. Also
* timer interrupts need to be acknowledged manually in
* the 8259A for the i82489DX when using the NMI
* watchdog as that APIC treats NMIs as level-triggered.
* The AEOI mode will finish them in the 8259A
* automatically.
*/
apic_write(APIC_LVT0, APIC_LVT_MASKED | APIC_DM_EXTINT);
init_8259A(1);
#ifdef CONFIG_X86_32
{
unsigned int ver;
ver = apic_read(APIC_LVR);
ver = GET_APIC_VERSION(ver);
timer_ack = (nmi_watchdog == NMI_IO_APIC && !APIC_INTEGRATED(ver));
}
#endif
pin1 = find_isa_irq_pin(0, mp_INT);
apic1 = find_isa_irq_apic(0, mp_INT);
pin2 = ioapic_i8259.pin;
apic2 = ioapic_i8259.apic;
apic_printk(APIC_QUIET, KERN_INFO "..TIMER: vector=0x%02X "
"apic1=%d pin1=%d apic2=%d pin2=%d\n",
cfg->vector, apic1, pin1, apic2, pin2);
/*
* Some BIOS writers are clueless and report the ExtINTA
* I/O APIC input from the cascaded 8259A as the timer
* interrupt input. So just in case, if only one pin
* was found above, try it both directly and through the
* 8259A.
*/
if (pin1 == -1) {
if (intr_remapping_enabled)
panic("BIOS bug: timer not connected to IO-APIC");
pin1 = pin2;
apic1 = apic2;
no_pin1 = 1;
} else if (pin2 == -1) {
pin2 = pin1;
apic2 = apic1;
}
if (pin1 != -1) {
/*
* Ok, does IRQ0 through the IOAPIC work?
*/
if (no_pin1) {
add_pin_to_irq_node(cfg, node, apic1, pin1);
setup_timer_IRQ0_pin(apic1, pin1, cfg->vector);
} else {
/* for edge trigger, setup_IO_APIC_irq already
* leave it unmasked.
* so only need to unmask if it is level-trigger
* do we really have level trigger timer?
*/
int idx;
idx = find_irq_entry(apic1, pin1, mp_INT);
if (idx != -1 && irq_trigger(idx))
unmask_IO_APIC_irq_desc(desc);
}
if (timer_irq_works()) {
if (nmi_watchdog == NMI_IO_APIC) {
setup_nmi();
enable_8259A_irq(0);
}
if (disable_timer_pin_1 > 0)
clear_IO_APIC_pin(0, pin1);
goto out;
}
if (intr_remapping_enabled)
panic("timer doesn't work through Interrupt-remapped IO-APIC");
local_irq_disable();
clear_IO_APIC_pin(apic1, pin1);
if (!no_pin1)
apic_printk(APIC_QUIET, KERN_ERR "..MP-BIOS bug: "
"8254 timer not connected to IO-APIC\n");
apic_printk(APIC_QUIET, KERN_INFO "...trying to set up timer "
"(IRQ0) through the 8259A ...\n");
apic_printk(APIC_QUIET, KERN_INFO
"..... (found apic %d pin %d) ...\n", apic2, pin2);
/*
* legacy devices should be connected to IO APIC #0
*/
replace_pin_at_irq_node(cfg, node, apic1, pin1, apic2, pin2);
setup_timer_IRQ0_pin(apic2, pin2, cfg->vector);
enable_8259A_irq(0);
if (timer_irq_works()) {
apic_printk(APIC_QUIET, KERN_INFO "....... works.\n");
timer_through_8259 = 1;
if (nmi_watchdog == NMI_IO_APIC) {
disable_8259A_irq(0);
setup_nmi();
enable_8259A_irq(0);
}
goto out;
}
/*
* Cleanup, just in case ...
*/
local_irq_disable();
disable_8259A_irq(0);
clear_IO_APIC_pin(apic2, pin2);
apic_printk(APIC_QUIET, KERN_INFO "....... failed.\n");
}
if (nmi_watchdog == NMI_IO_APIC) {
apic_printk(APIC_QUIET, KERN_WARNING "timer doesn't work "
"through the IO-APIC - disabling NMI Watchdog!\n");
nmi_watchdog = NMI_NONE;
}
#ifdef CONFIG_X86_32
timer_ack = 0;
#endif
apic_printk(APIC_QUIET, KERN_INFO
"...trying to set up timer as Virtual Wire IRQ...\n");
lapic_register_intr(0, desc);
apic_write(APIC_LVT0, APIC_DM_FIXED | cfg->vector); /* Fixed mode */
enable_8259A_irq(0);
if (timer_irq_works()) {
apic_printk(APIC_QUIET, KERN_INFO "..... works.\n");
goto out;
}
local_irq_disable();
disable_8259A_irq(0);
apic_write(APIC_LVT0, APIC_LVT_MASKED | APIC_DM_FIXED | cfg->vector);
apic_printk(APIC_QUIET, KERN_INFO "..... failed.\n");
apic_printk(APIC_QUIET, KERN_INFO
"...trying to set up timer as ExtINT IRQ...\n");
init_8259A(0);
make_8259A_irq(0);
apic_write(APIC_LVT0, APIC_DM_EXTINT);
unlock_ExtINT_logic();
if (timer_irq_works()) {
apic_printk(APIC_QUIET, KERN_INFO "..... works.\n");
goto out;
}
local_irq_disable();
apic_printk(APIC_QUIET, KERN_INFO "..... failed :(.\n");
panic("IO-APIC + timer doesn't work! Boot with apic=debug and send a "
"report. Then try booting with the 'noapic' option.\n");
out:
local_irq_restore(flags);
}
/*
* Traditionally ISA IRQ2 is the cascade IRQ, and is not available
* to devices. However there may be an I/O APIC pin available for
* this interrupt regardless. The pin may be left unconnected, but
* typically it will be reused as an ExtINT cascade interrupt for
* the master 8259A. In the MPS case such a pin will normally be
* reported as an ExtINT interrupt in the MP table. With ACPI
* there is no provision for ExtINT interrupts, and in the absence
* of an override it would be treated as an ordinary ISA I/O APIC
* interrupt, that is edge-triggered and unmasked by default. We
* used to do this, but it caused problems on some systems because
* of the NMI watchdog and sometimes IRQ0 of the 8254 timer using
* the same ExtINT cascade interrupt to drive the local APIC of the
* bootstrap processor. Therefore we refrain from routing IRQ2 to
* the I/O APIC in all cases now. No actual device should request
* it anyway. --macro
*/
#define PIC_IRQS (1UL << PIC_CASCADE_IR)
void __init setup_IO_APIC(void)
{
/*
* calling enable_IO_APIC() is moved to setup_local_APIC for BP
*/
io_apic_irqs = nr_legacy_irqs ? ~PIC_IRQS : ~0UL;
apic_printk(APIC_VERBOSE, "ENABLING IO-APIC IRQs\n");
/*
* Set up IO-APIC IRQ routing.
*/
x86_init.mpparse.setup_ioapic_ids();
sync_Arb_IDs();
setup_IO_APIC_irqs();
init_IO_APIC_traps();
if (nr_legacy_irqs)
check_timer();
}
/*
* Called after all the initialization is done. If we didnt find any
* APIC bugs then we can allow the modify fast path
*/
static int __init io_apic_bug_finalize(void)
{
if (sis_apic_bug == -1)
sis_apic_bug = 0;
return 0;
}
late_initcall(io_apic_bug_finalize);
struct sysfs_ioapic_data {
struct sys_device dev;
struct IO_APIC_route_entry entry[0];
};
static struct sysfs_ioapic_data * mp_ioapic_data[MAX_IO_APICS];
static int ioapic_suspend(struct sys_device *dev, pm_message_t state)
{
struct IO_APIC_route_entry *entry;
struct sysfs_ioapic_data *data;
int i;
data = container_of(dev, struct sysfs_ioapic_data, dev);
entry = data->entry;
for (i = 0; i < nr_ioapic_registers[dev->id]; i ++, entry ++ )
*entry = ioapic_read_entry(dev->id, i);
return 0;
}
static int ioapic_resume(struct sys_device *dev)
{
struct IO_APIC_route_entry *entry;
struct sysfs_ioapic_data *data;
unsigned long flags;
union IO_APIC_reg_00 reg_00;
int i;
data = container_of(dev, struct sysfs_ioapic_data, dev);
entry = data->entry;
spin_lock_irqsave(&ioapic_lock, flags);
reg_00.raw = io_apic_read(dev->id, 0);
if (reg_00.bits.ID != mp_ioapics[dev->id].apicid) {
reg_00.bits.ID = mp_ioapics[dev->id].apicid;
io_apic_write(dev->id, 0, reg_00.raw);
}
spin_unlock_irqrestore(&ioapic_lock, flags);
for (i = 0; i < nr_ioapic_registers[dev->id]; i++)
ioapic_write_entry(dev->id, i, entry[i]);
return 0;
}
static struct sysdev_class ioapic_sysdev_class = {
.name = "ioapic",
.suspend = ioapic_suspend,
.resume = ioapic_resume,
};
static int __init ioapic_init_sysfs(void)
{
struct sys_device * dev;
int i, size, error;
error = sysdev_class_register(&ioapic_sysdev_class);
if (error)
return error;
for (i = 0; i < nr_ioapics; i++ ) {
size = sizeof(struct sys_device) + nr_ioapic_registers[i]
* sizeof(struct IO_APIC_route_entry);
mp_ioapic_data[i] = kzalloc(size, GFP_KERNEL);
if (!mp_ioapic_data[i]) {
printk(KERN_ERR "Can't suspend/resume IOAPIC %d\n", i);
continue;
}
dev = &mp_ioapic_data[i]->dev;
dev->id = i;
dev->cls = &ioapic_sysdev_class;
error = sysdev_register(dev);
if (error) {
kfree(mp_ioapic_data[i]);
mp_ioapic_data[i] = NULL;
printk(KERN_ERR "Can't suspend/resume IOAPIC %d\n", i);
continue;
}
}
return 0;
}
device_initcall(ioapic_init_sysfs);
/*
* Dynamic irq allocate and deallocation
*/
unsigned int create_irq_nr(unsigned int irq_want, int node)
{
/* Allocate an unused irq */
unsigned int irq;
unsigned int new;
unsigned long flags;
struct irq_cfg *cfg_new = NULL;
struct irq_desc *desc_new = NULL;
irq = 0;
if (irq_want < nr_irqs_gsi)
irq_want = nr_irqs_gsi;
spin_lock_irqsave(&vector_lock, flags);
for (new = irq_want; new < nr_irqs; new++) {
desc_new = irq_to_desc_alloc_node(new, node);
if (!desc_new) {
printk(KERN_INFO "can not get irq_desc for %d\n", new);
continue;
}
cfg_new = desc_new->chip_data;
if (cfg_new->vector != 0)
continue;
desc_new = move_irq_desc(desc_new, node);
if (__assign_irq_vector(new, cfg_new, apic->target_cpus()) == 0)
irq = new;
break;
}
spin_unlock_irqrestore(&vector_lock, flags);
if (irq > 0) {
dynamic_irq_init(irq);
/* restore it, in case dynamic_irq_init clear it */
if (desc_new)
desc_new->chip_data = cfg_new;
}
return irq;
}
int create_irq(void)
{
int node = cpu_to_node(boot_cpu_id);
unsigned int irq_want;
int irq;
irq_want = nr_irqs_gsi;
irq = create_irq_nr(irq_want, node);
if (irq == 0)
irq = -1;
return irq;
}
void destroy_irq(unsigned int irq)
{
unsigned long flags;
struct irq_cfg *cfg;
struct irq_desc *desc;
/* store it, in case dynamic_irq_cleanup clear it */
desc = irq_to_desc(irq);
cfg = desc->chip_data;
dynamic_irq_cleanup(irq);
/* connect back irq_cfg */
desc->chip_data = cfg;
free_irte(irq);
spin_lock_irqsave(&vector_lock, flags);
__clear_irq_vector(irq, cfg);
spin_unlock_irqrestore(&vector_lock, flags);
}
/*
* MSI message composition
*/
#ifdef CONFIG_PCI_MSI
static int msi_compose_msg(struct pci_dev *pdev, unsigned int irq, struct msi_msg *msg)
{
struct irq_cfg *cfg;
int err;
unsigned dest;
if (disable_apic)
return -ENXIO;
cfg = irq_cfg(irq);
err = assign_irq_vector(irq, cfg, apic->target_cpus());
if (err)
return err;
dest = apic->cpu_mask_to_apicid_and(cfg->domain, apic->target_cpus());
if (irq_remapped(irq)) {
struct irte irte;
int ir_index;
u16 sub_handle;
ir_index = map_irq_to_irte_handle(irq, &sub_handle);
BUG_ON(ir_index == -1);
memset (&irte, 0, sizeof(irte));
irte.present = 1;
irte.dst_mode = apic->irq_dest_mode;
irte.trigger_mode = 0; /* edge */
irte.dlvry_mode = apic->irq_delivery_mode;
irte.vector = cfg->vector;
irte.dest_id = IRTE_DEST(dest);
/* Set source-id of interrupt request */
set_msi_sid(&irte, pdev);
modify_irte(irq, &irte);
msg->address_hi = MSI_ADDR_BASE_HI;
msg->data = sub_handle;
msg->address_lo = MSI_ADDR_BASE_LO | MSI_ADDR_IR_EXT_INT |
MSI_ADDR_IR_SHV |
MSI_ADDR_IR_INDEX1(ir_index) |
MSI_ADDR_IR_INDEX2(ir_index);
} else {
if (x2apic_enabled())
msg->address_hi = MSI_ADDR_BASE_HI |
MSI_ADDR_EXT_DEST_ID(dest);
else
msg->address_hi = MSI_ADDR_BASE_HI;
msg->address_lo =
MSI_ADDR_BASE_LO |
((apic->irq_dest_mode == 0) ?
MSI_ADDR_DEST_MODE_PHYSICAL:
MSI_ADDR_DEST_MODE_LOGICAL) |
((apic->irq_delivery_mode != dest_LowestPrio) ?
MSI_ADDR_REDIRECTION_CPU:
MSI_ADDR_REDIRECTION_LOWPRI) |
MSI_ADDR_DEST_ID(dest);
msg->data =
MSI_DATA_TRIGGER_EDGE |
MSI_DATA_LEVEL_ASSERT |
((apic->irq_delivery_mode != dest_LowestPrio) ?
MSI_DATA_DELIVERY_FIXED:
MSI_DATA_DELIVERY_LOWPRI) |
MSI_DATA_VECTOR(cfg->vector);
}
return err;
}
#ifdef CONFIG_SMP
static int set_msi_irq_affinity(unsigned int irq, const struct cpumask *mask)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irq_cfg *cfg;
struct msi_msg msg;
unsigned int dest;
dest = set_desc_affinity(desc, mask);
if (dest == BAD_APICID)
return -1;
cfg = desc->chip_data;
read_msi_msg_desc(desc, &msg);
msg.data &= ~MSI_DATA_VECTOR_MASK;
msg.data |= MSI_DATA_VECTOR(cfg->vector);
msg.address_lo &= ~MSI_ADDR_DEST_ID_MASK;
msg.address_lo |= MSI_ADDR_DEST_ID(dest);
write_msi_msg_desc(desc, &msg);
return 0;
}
#ifdef CONFIG_INTR_REMAP
/*
* Migrate the MSI irq to another cpumask. This migration is
* done in the process context using interrupt-remapping hardware.
*/
static int
ir_set_msi_irq_affinity(unsigned int irq, const struct cpumask *mask)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irq_cfg *cfg = desc->chip_data;
unsigned int dest;
struct irte irte;
if (get_irte(irq, &irte))
return -1;
dest = set_desc_affinity(desc, mask);
if (dest == BAD_APICID)
return -1;
irte.vector = cfg->vector;
irte.dest_id = IRTE_DEST(dest);
/*
* atomically update the IRTE with the new destination and vector.
*/
modify_irte(irq, &irte);
/*
* After this point, all the interrupts will start arriving
* at the new destination. So, time to cleanup the previous
* vector allocation.
*/
if (cfg->move_in_progress)
send_cleanup_vector(cfg);
return 0;
}
#endif
#endif /* CONFIG_SMP */
/*
* IRQ Chip for MSI PCI/PCI-X/PCI-Express Devices,
* which implement the MSI or MSI-X Capability Structure.
*/
static struct irq_chip msi_chip = {
.name = "PCI-MSI",
.unmask = unmask_msi_irq,
.mask = mask_msi_irq,
.ack = ack_apic_edge,
#ifdef CONFIG_SMP
.set_affinity = set_msi_irq_affinity,
#endif
.retrigger = ioapic_retrigger_irq,
};
static struct irq_chip msi_ir_chip = {
.name = "IR-PCI-MSI",
.unmask = unmask_msi_irq,
.mask = mask_msi_irq,
#ifdef CONFIG_INTR_REMAP
.ack = ir_ack_apic_edge,
#ifdef CONFIG_SMP
.set_affinity = ir_set_msi_irq_affinity,
#endif
#endif
.retrigger = ioapic_retrigger_irq,
};
/*
* Map the PCI dev to the corresponding remapping hardware unit
* and allocate 'nvec' consecutive interrupt-remapping table entries
* in it.
*/
static int msi_alloc_irte(struct pci_dev *dev, int irq, int nvec)
{
struct intel_iommu *iommu;
int index;
iommu = map_dev_to_ir(dev);
if (!iommu) {
printk(KERN_ERR
"Unable to map PCI %s to iommu\n", pci_name(dev));
return -ENOENT;
}
index = alloc_irte(iommu, irq, nvec);
if (index < 0) {
printk(KERN_ERR
"Unable to allocate %d IRTE for PCI %s\n", nvec,
pci_name(dev));
return -ENOSPC;
}
return index;
}
static int setup_msi_irq(struct pci_dev *dev, struct msi_desc *msidesc, int irq)
{
int ret;
struct msi_msg msg;
ret = msi_compose_msg(dev, irq, &msg);
if (ret < 0)
return ret;
set_irq_msi(irq, msidesc);
write_msi_msg(irq, &msg);
if (irq_remapped(irq)) {
struct irq_desc *desc = irq_to_desc(irq);
/*
* irq migration in process context
*/
desc->status |= IRQ_MOVE_PCNTXT;
set_irq_chip_and_handler_name(irq, &msi_ir_chip, handle_edge_irq, "edge");
} else
set_irq_chip_and_handler_name(irq, &msi_chip, handle_edge_irq, "edge");
dev_printk(KERN_DEBUG, &dev->dev, "irq %d for MSI/MSI-X\n", irq);
return 0;
}
int arch_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
{
unsigned int irq;
int ret, sub_handle;
struct msi_desc *msidesc;
unsigned int irq_want;
struct intel_iommu *iommu = NULL;
int index = 0;
int node;
/* x86 doesn't support multiple MSI yet */
if (type == PCI_CAP_ID_MSI && nvec > 1)
return 1;
node = dev_to_node(&dev->dev);
irq_want = nr_irqs_gsi;
sub_handle = 0;
list_for_each_entry(msidesc, &dev->msi_list, list) {
irq = create_irq_nr(irq_want, node);
if (irq == 0)
return -1;
irq_want = irq + 1;
if (!intr_remapping_enabled)
goto no_ir;
if (!sub_handle) {
/*
* allocate the consecutive block of IRTE's
* for 'nvec'
*/
index = msi_alloc_irte(dev, irq, nvec);
if (index < 0) {
ret = index;
goto error;
}
} else {
iommu = map_dev_to_ir(dev);
if (!iommu) {
ret = -ENOENT;
goto error;
}
/*
* setup the mapping between the irq and the IRTE
* base index, the sub_handle pointing to the
* appropriate interrupt remap table entry.
*/
set_irte_irq(irq, iommu, index, sub_handle);
}
no_ir:
ret = setup_msi_irq(dev, msidesc, irq);
if (ret < 0)
goto error;
sub_handle++;
}
return 0;
error:
destroy_irq(irq);
return ret;
}
void arch_teardown_msi_irq(unsigned int irq)
{
destroy_irq(irq);
}
#if defined (CONFIG_DMAR) || defined (CONFIG_INTR_REMAP)
#ifdef CONFIG_SMP
static int dmar_msi_set_affinity(unsigned int irq, const struct cpumask *mask)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irq_cfg *cfg;
struct msi_msg msg;
unsigned int dest;
dest = set_desc_affinity(desc, mask);
if (dest == BAD_APICID)
return -1;
cfg = desc->chip_data;
dmar_msi_read(irq, &msg);
msg.data &= ~MSI_DATA_VECTOR_MASK;
msg.data |= MSI_DATA_VECTOR(cfg->vector);
msg.address_lo &= ~MSI_ADDR_DEST_ID_MASK;
msg.address_lo |= MSI_ADDR_DEST_ID(dest);
dmar_msi_write(irq, &msg);
return 0;
}
#endif /* CONFIG_SMP */
static struct irq_chip dmar_msi_type = {
.name = "DMAR_MSI",
.unmask = dmar_msi_unmask,
.mask = dmar_msi_mask,
.ack = ack_apic_edge,
#ifdef CONFIG_SMP
.set_affinity = dmar_msi_set_affinity,
#endif
.retrigger = ioapic_retrigger_irq,
};
int arch_setup_dmar_msi(unsigned int irq)
{
int ret;
struct msi_msg msg;
ret = msi_compose_msg(NULL, irq, &msg);
if (ret < 0)
return ret;
dmar_msi_write(irq, &msg);
set_irq_chip_and_handler_name(irq, &dmar_msi_type, handle_edge_irq,
"edge");
return 0;
}
#endif
#ifdef CONFIG_HPET_TIMER
#ifdef CONFIG_SMP
static int hpet_msi_set_affinity(unsigned int irq, const struct cpumask *mask)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irq_cfg *cfg;
struct msi_msg msg;
unsigned int dest;
dest = set_desc_affinity(desc, mask);
if (dest == BAD_APICID)
return -1;
cfg = desc->chip_data;
hpet_msi_read(irq, &msg);
msg.data &= ~MSI_DATA_VECTOR_MASK;
msg.data |= MSI_DATA_VECTOR(cfg->vector);
msg.address_lo &= ~MSI_ADDR_DEST_ID_MASK;
msg.address_lo |= MSI_ADDR_DEST_ID(dest);
hpet_msi_write(irq, &msg);
return 0;
}
#endif /* CONFIG_SMP */
static struct irq_chip hpet_msi_type = {
.name = "HPET_MSI",
.unmask = hpet_msi_unmask,
.mask = hpet_msi_mask,
.ack = ack_apic_edge,
#ifdef CONFIG_SMP
.set_affinity = hpet_msi_set_affinity,
#endif
.retrigger = ioapic_retrigger_irq,
};
int arch_setup_hpet_msi(unsigned int irq)
{
int ret;
struct msi_msg msg;
struct irq_desc *desc = irq_to_desc(irq);
ret = msi_compose_msg(NULL, irq, &msg);
if (ret < 0)
return ret;
hpet_msi_write(irq, &msg);
desc->status |= IRQ_MOVE_PCNTXT;
set_irq_chip_and_handler_name(irq, &hpet_msi_type, handle_edge_irq,
"edge");
return 0;
}
#endif
#endif /* CONFIG_PCI_MSI */
/*
* Hypertransport interrupt support
*/
#ifdef CONFIG_HT_IRQ
#ifdef CONFIG_SMP
static void target_ht_irq(unsigned int irq, unsigned int dest, u8 vector)
{
struct ht_irq_msg msg;
fetch_ht_irq_msg(irq, &msg);
msg.address_lo &= ~(HT_IRQ_LOW_VECTOR_MASK | HT_IRQ_LOW_DEST_ID_MASK);
msg.address_hi &= ~(HT_IRQ_HIGH_DEST_ID_MASK);
msg.address_lo |= HT_IRQ_LOW_VECTOR(vector) | HT_IRQ_LOW_DEST_ID(dest);
msg.address_hi |= HT_IRQ_HIGH_DEST_ID(dest);
write_ht_irq_msg(irq, &msg);
}
static int set_ht_irq_affinity(unsigned int irq, const struct cpumask *mask)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irq_cfg *cfg;
unsigned int dest;
dest = set_desc_affinity(desc, mask);
if (dest == BAD_APICID)
return -1;
cfg = desc->chip_data;
target_ht_irq(irq, dest, cfg->vector);
return 0;
}
#endif
static struct irq_chip ht_irq_chip = {
.name = "PCI-HT",
.mask = mask_ht_irq,
.unmask = unmask_ht_irq,
.ack = ack_apic_edge,
#ifdef CONFIG_SMP
.set_affinity = set_ht_irq_affinity,
#endif
.retrigger = ioapic_retrigger_irq,
};
int arch_setup_ht_irq(unsigned int irq, struct pci_dev *dev)
{
struct irq_cfg *cfg;
int err;
if (disable_apic)
return -ENXIO;
cfg = irq_cfg(irq);
err = assign_irq_vector(irq, cfg, apic->target_cpus());
if (!err) {
struct ht_irq_msg msg;
unsigned dest;
dest = apic->cpu_mask_to_apicid_and(cfg->domain,
apic->target_cpus());
msg.address_hi = HT_IRQ_HIGH_DEST_ID(dest);
msg.address_lo =
HT_IRQ_LOW_BASE |
HT_IRQ_LOW_DEST_ID(dest) |
HT_IRQ_LOW_VECTOR(cfg->vector) |
((apic->irq_dest_mode == 0) ?
HT_IRQ_LOW_DM_PHYSICAL :
HT_IRQ_LOW_DM_LOGICAL) |
HT_IRQ_LOW_RQEOI_EDGE |
((apic->irq_delivery_mode != dest_LowestPrio) ?
HT_IRQ_LOW_MT_FIXED :
HT_IRQ_LOW_MT_ARBITRATED) |
HT_IRQ_LOW_IRQ_MASKED;
write_ht_irq_msg(irq, &msg);
set_irq_chip_and_handler_name(irq, &ht_irq_chip,
handle_edge_irq, "edge");
dev_printk(KERN_DEBUG, &dev->dev, "irq %d for HT\n", irq);
}
return err;
}
#endif /* CONFIG_HT_IRQ */
int __init io_apic_get_redir_entries (int ioapic)
{
union IO_APIC_reg_01 reg_01;
unsigned long flags;
spin_lock_irqsave(&ioapic_lock, flags);
reg_01.raw = io_apic_read(ioapic, 1);
spin_unlock_irqrestore(&ioapic_lock, flags);
return reg_01.bits.entries;
}
void __init probe_nr_irqs_gsi(void)
{
int nr = 0;
nr = acpi_probe_gsi();
if (nr > nr_irqs_gsi) {
nr_irqs_gsi = nr;
} else {
/* for acpi=off or acpi is not compiled in */
int idx;
nr = 0;
for (idx = 0; idx < nr_ioapics; idx++)
nr += io_apic_get_redir_entries(idx) + 1;
if (nr > nr_irqs_gsi)
nr_irqs_gsi = nr;
}
printk(KERN_DEBUG "nr_irqs_gsi: %d\n", nr_irqs_gsi);
}
#ifdef CONFIG_SPARSE_IRQ
int __init arch_probe_nr_irqs(void)
{
int nr;
if (nr_irqs > (NR_VECTORS * nr_cpu_ids))
nr_irqs = NR_VECTORS * nr_cpu_ids;
nr = nr_irqs_gsi + 8 * nr_cpu_ids;
#if defined(CONFIG_PCI_MSI) || defined(CONFIG_HT_IRQ)
/*
* for MSI and HT dyn irq
*/
nr += nr_irqs_gsi * 16;
#endif
if (nr < nr_irqs)
nr_irqs = nr;
return 0;
}
#endif
static int __io_apic_set_pci_routing(struct device *dev, int irq,
struct io_apic_irq_attr *irq_attr)
{
struct irq_desc *desc;
struct irq_cfg *cfg;
int node;
int ioapic, pin;
int trigger, polarity;
ioapic = irq_attr->ioapic;
if (!IO_APIC_IRQ(irq)) {
apic_printk(APIC_QUIET,KERN_ERR "IOAPIC[%d]: Invalid reference to IRQ 0\n",
ioapic);
return -EINVAL;
}
if (dev)
node = dev_to_node(dev);
else
node = cpu_to_node(boot_cpu_id);
desc = irq_to_desc_alloc_node(irq, node);
if (!desc) {
printk(KERN_INFO "can not get irq_desc %d\n", irq);
return 0;
}
pin = irq_attr->ioapic_pin;
trigger = irq_attr->trigger;
polarity = irq_attr->polarity;
/*
* IRQs < 16 are already in the irq_2_pin[] map
*/
if (irq >= nr_legacy_irqs) {
cfg = desc->chip_data;
if (add_pin_to_irq_node_nopanic(cfg, node, ioapic, pin)) {
printk(KERN_INFO "can not add pin %d for irq %d\n",
pin, irq);
return 0;
}
}
setup_IO_APIC_irq(ioapic, pin, irq, desc, trigger, polarity);
return 0;
}
int io_apic_set_pci_routing(struct device *dev, int irq,
struct io_apic_irq_attr *irq_attr)
{
int ioapic, pin;
/*
* Avoid pin reprogramming. PRTs typically include entries
* with redundant pin->gsi mappings (but unique PCI devices);
* we only program the IOAPIC on the first.
*/
ioapic = irq_attr->ioapic;
pin = irq_attr->ioapic_pin;
if (test_bit(pin, mp_ioapic_routing[ioapic].pin_programmed)) {
pr_debug("Pin %d-%d already programmed\n",
mp_ioapics[ioapic].apicid, pin);
return 0;
}
set_bit(pin, mp_ioapic_routing[ioapic].pin_programmed);
return __io_apic_set_pci_routing(dev, irq, irq_attr);
}
u8 __init io_apic_unique_id(u8 id)
{
#ifdef CONFIG_X86_32
if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) &&
!APIC_XAPIC(apic_version[boot_cpu_physical_apicid]))
return io_apic_get_unique_id(nr_ioapics, id);
else
return id;
#else
int i;
DECLARE_BITMAP(used, 256);
bitmap_zero(used, 256);
for (i = 0; i < nr_ioapics; i++) {
struct mpc_ioapic *ia = &mp_ioapics[i];
__set_bit(ia->apicid, used);
}
if (!test_bit(id, used))
return id;
return find_first_zero_bit(used, 256);
#endif
}
#ifdef CONFIG_X86_32
int __init io_apic_get_unique_id(int ioapic, int apic_id)
{
union IO_APIC_reg_00 reg_00;
static physid_mask_t apic_id_map = PHYSID_MASK_NONE;
physid_mask_t tmp;
unsigned long flags;
int i = 0;
/*
* The P4 platform supports up to 256 APIC IDs on two separate APIC
* buses (one for LAPICs, one for IOAPICs), where predecessors only
* supports up to 16 on one shared APIC bus.
*
* TBD: Expand LAPIC/IOAPIC support on P4-class systems to take full
* advantage of new APIC bus architecture.
*/
if (physids_empty(apic_id_map))
apic_id_map = apic->ioapic_phys_id_map(phys_cpu_present_map);
spin_lock_irqsave(&ioapic_lock, flags);
reg_00.raw = io_apic_read(ioapic, 0);
spin_unlock_irqrestore(&ioapic_lock, flags);
if (apic_id >= get_physical_broadcast()) {
printk(KERN_WARNING "IOAPIC[%d]: Invalid apic_id %d, trying "
"%d\n", ioapic, apic_id, reg_00.bits.ID);
apic_id = reg_00.bits.ID;
}
/*
* Every APIC in a system must have a unique ID or we get lots of nice
* 'stuck on smp_invalidate_needed IPI wait' messages.
*/
if (apic->check_apicid_used(apic_id_map, apic_id)) {
for (i = 0; i < get_physical_broadcast(); i++) {
if (!apic->check_apicid_used(apic_id_map, i))
break;
}
if (i == get_physical_broadcast())
panic("Max apic_id exceeded!\n");
printk(KERN_WARNING "IOAPIC[%d]: apic_id %d already used, "
"trying %d\n", ioapic, apic_id, i);
apic_id = i;
}
tmp = apic->apicid_to_cpu_present(apic_id);
physids_or(apic_id_map, apic_id_map, tmp);
if (reg_00.bits.ID != apic_id) {
reg_00.bits.ID = apic_id;
spin_lock_irqsave(&ioapic_lock, flags);
io_apic_write(ioapic, 0, reg_00.raw);
reg_00.raw = io_apic_read(ioapic, 0);
spin_unlock_irqrestore(&ioapic_lock, flags);
/* Sanity check */
if (reg_00.bits.ID != apic_id) {
printk("IOAPIC[%d]: Unable to change apic_id!\n", ioapic);
return -1;
}
}
apic_printk(APIC_VERBOSE, KERN_INFO
"IOAPIC[%d]: Assigned apic_id %d\n", ioapic, apic_id);
return apic_id;
}
#endif
int __init io_apic_get_version(int ioapic)
{
union IO_APIC_reg_01 reg_01;
unsigned long flags;
spin_lock_irqsave(&ioapic_lock, flags);
reg_01.raw = io_apic_read(ioapic, 1);
spin_unlock_irqrestore(&ioapic_lock, flags);
return reg_01.bits.version;
}
int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
{
int i;
if (skip_ioapic_setup)
return -1;
for (i = 0; i < mp_irq_entries; i++)
if (mp_irqs[i].irqtype == mp_INT &&
mp_irqs[i].srcbusirq == bus_irq)
break;
if (i >= mp_irq_entries)
return -1;
*trigger = irq_trigger(i);
*polarity = irq_polarity(i);
return 0;
}
/*
* This function currently is only a helper for the i386 smp boot process where
* we need to reprogram the ioredtbls to cater for the cpus which have come online
* so mask in all cases should simply be apic->target_cpus()
*/
#ifdef CONFIG_SMP
void __init setup_ioapic_dest(void)
{
int pin, ioapic = 0, irq, irq_entry;
struct irq_desc *desc;
const struct cpumask *mask;
if (skip_ioapic_setup == 1)
return;
#ifdef CONFIG_ACPI
if (!acpi_disabled && acpi_ioapic) {
ioapic = mp_find_ioapic(0);
if (ioapic < 0)
ioapic = 0;
}
#endif
for (pin = 0; pin < nr_ioapic_registers[ioapic]; pin++) {
irq_entry = find_irq_entry(ioapic, pin, mp_INT);
if (irq_entry == -1)
continue;
irq = pin_2_irq(irq_entry, ioapic, pin);
desc = irq_to_desc(irq);
/*
* Honour affinities which have been set in early boot
*/
if (desc->status &
(IRQ_NO_BALANCING | IRQ_AFFINITY_SET))
mask = desc->affinity;
else
mask = apic->target_cpus();
if (intr_remapping_enabled)
set_ir_ioapic_affinity_irq_desc(desc, mask);
else
set_ioapic_affinity_irq_desc(desc, mask);
}
}
#endif
#define IOAPIC_RESOURCE_NAME_SIZE 11
static struct resource *ioapic_resources;
static struct resource * __init ioapic_setup_resources(int nr_ioapics)
{
unsigned long n;
struct resource *res;
char *mem;
int i;
if (nr_ioapics <= 0)
return NULL;
n = IOAPIC_RESOURCE_NAME_SIZE + sizeof(struct resource);
n *= nr_ioapics;
mem = alloc_bootmem(n);
res = (void *)mem;
mem += sizeof(struct resource) * nr_ioapics;
for (i = 0; i < nr_ioapics; i++) {
res[i].name = mem;
res[i].flags = IORESOURCE_MEM | IORESOURCE_BUSY;
sprintf(mem, "IOAPIC %u", i);
mem += IOAPIC_RESOURCE_NAME_SIZE;
}
ioapic_resources = res;
return res;
}
void __init ioapic_init_mappings(void)
{
unsigned long ioapic_phys, idx = FIX_IO_APIC_BASE_0;
struct resource *ioapic_res;
int i;
ioapic_res = ioapic_setup_resources(nr_ioapics);
for (i = 0; i < nr_ioapics; i++) {
if (smp_found_config) {
ioapic_phys = mp_ioapics[i].apicaddr;
#ifdef CONFIG_X86_32
if (!ioapic_phys) {
printk(KERN_ERR
"WARNING: bogus zero IO-APIC "
"address found in MPTABLE, "
"disabling IO/APIC support!\n");
smp_found_config = 0;
skip_ioapic_setup = 1;
goto fake_ioapic_page;
}
#endif
} else {
#ifdef CONFIG_X86_32
fake_ioapic_page:
#endif
ioapic_phys = (unsigned long)
alloc_bootmem_pages(PAGE_SIZE);
ioapic_phys = __pa(ioapic_phys);
}
set_fixmap_nocache(idx, ioapic_phys);
apic_printk(APIC_VERBOSE,
"mapped IOAPIC to %08lx (%08lx)\n",
__fix_to_virt(idx), ioapic_phys);
idx++;
ioapic_res->start = ioapic_phys;
ioapic_res->end = ioapic_phys + (4 * 1024) - 1;
ioapic_res++;
}
}
void __init ioapic_insert_resources(void)
{
int i;
struct resource *r = ioapic_resources;
if (!r) {
if (nr_ioapics > 0)
printk(KERN_ERR
"IO APIC resources couldn't be allocated.\n");
return;
}
for (i = 0; i < nr_ioapics; i++) {
insert_resource(&iomem_resource, r);
r++;
}
}
int mp_find_ioapic(int gsi)
{
int i = 0;
/* Find the IOAPIC that manages this GSI. */
for (i = 0; i < nr_ioapics; i++) {
if ((gsi >= mp_gsi_routing[i].gsi_base)
&& (gsi <= mp_gsi_routing[i].gsi_end))
return i;
}
printk(KERN_ERR "ERROR: Unable to locate IOAPIC for GSI %d\n", gsi);
return -1;
}
int mp_find_ioapic_pin(int ioapic, int gsi)
{
if (WARN_ON(ioapic == -1))
return -1;
if (WARN_ON(gsi > mp_gsi_routing[ioapic].gsi_end))
return -1;
return gsi - mp_gsi_routing[ioapic].gsi_base;
}
static int bad_ioapic(unsigned long address)
{
if (nr_ioapics >= MAX_IO_APICS) {
printk(KERN_WARNING "WARING: Max # of I/O APICs (%d) exceeded "
"(found %d), skipping\n", MAX_IO_APICS, nr_ioapics);
return 1;
}
if (!address) {
printk(KERN_WARNING "WARNING: Bogus (zero) I/O APIC address"
" found in table, skipping!\n");
return 1;
}
return 0;
}
void __init mp_register_ioapic(int id, u32 address, u32 gsi_base)
{
int idx = 0;
if (bad_ioapic(address))
return;
idx = nr_ioapics;
mp_ioapics[idx].type = MP_IOAPIC;
mp_ioapics[idx].flags = MPC_APIC_USABLE;
mp_ioapics[idx].apicaddr = address;
set_fixmap_nocache(FIX_IO_APIC_BASE_0 + idx, address);
mp_ioapics[idx].apicid = io_apic_unique_id(id);
mp_ioapics[idx].apicver = io_apic_get_version(idx);
/*
* Build basic GSI lookup table to facilitate gsi->io_apic lookups
* and to prevent reprogramming of IOAPIC pins (PCI GSIs).
*/
mp_gsi_routing[idx].gsi_base = gsi_base;
mp_gsi_routing[idx].gsi_end = gsi_base +
io_apic_get_redir_entries(idx);
printk(KERN_INFO "IOAPIC[%d]: apic_id %d, version %d, address 0x%x, "
"GSI %d-%d\n", idx, mp_ioapics[idx].apicid,
mp_ioapics[idx].apicver, mp_ioapics[idx].apicaddr,
mp_gsi_routing[idx].gsi_base, mp_gsi_routing[idx].gsi_end);
nr_ioapics++;
}