786 lines
25 KiB
Plaintext
786 lines
25 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
#
|
|
# USB Host Controller Drivers
|
|
#
|
|
comment "USB Host Controller Drivers"
|
|
|
|
config USB_C67X00_HCD
|
|
tristate "Cypress C67x00 HCD support"
|
|
depends on HAS_IOMEM
|
|
help
|
|
The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
|
|
host/peripheral/OTG USB controllers.
|
|
|
|
Enable this option to support this chip in host controller mode.
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called c67x00.
|
|
|
|
config USB_XHCI_HCD
|
|
tristate "xHCI HCD (USB 3.0) support"
|
|
depends on HAS_DMA && HAS_IOMEM
|
|
help
|
|
The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
|
|
"SuperSpeed" host controller hardware.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called xhci-hcd.
|
|
|
|
if USB_XHCI_HCD
|
|
config USB_XHCI_DBGCAP
|
|
bool "xHCI support for debug capability"
|
|
depends on TTY
|
|
help
|
|
Say 'Y' to enable the support for the xHCI debug capability. Make
|
|
sure that your xHCI host supports the extended debug capability and
|
|
you want a TTY serial device based on the xHCI debug capability
|
|
before enabling this option. If unsure, say 'N'.
|
|
|
|
config USB_XHCI_PCI
|
|
tristate
|
|
depends on USB_PCI
|
|
depends on USB_XHCI_PCI_RENESAS || !USB_XHCI_PCI_RENESAS
|
|
default y
|
|
|
|
config USB_XHCI_PCI_RENESAS
|
|
tristate "Support for additional Renesas xHCI controller with firmware"
|
|
help
|
|
Say 'Y' to enable the support for the Renesas xHCI controller with
|
|
firmware. Make sure you have the firwmare for the device and
|
|
installed on your system for this device to work.
|
|
If unsure, say 'N'.
|
|
|
|
config USB_XHCI_PLATFORM
|
|
tristate "Generic xHCI driver for a platform device"
|
|
select USB_XHCI_RCAR if ARCH_RENESAS
|
|
help
|
|
Adds an xHCI host driver for a generic platform device, which
|
|
provides a memory space and an irq.
|
|
It is also a prerequisite for platform specific drivers that
|
|
implement some extra quirks.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_XHCI_HISTB
|
|
tristate "xHCI support for HiSilicon STB SoCs"
|
|
depends on USB_XHCI_PLATFORM && (ARCH_HISI || COMPILE_TEST)
|
|
help
|
|
Say 'Y' to enable the support for the xHCI host controller
|
|
found in HiSilicon STB SoCs.
|
|
|
|
config USB_XHCI_MTK
|
|
tristate "xHCI support for MediaTek SoCs"
|
|
select MFD_SYSCON
|
|
depends on (MIPS && SOC_MT7621) || ARCH_MEDIATEK || COMPILE_TEST
|
|
help
|
|
Say 'Y' to enable the support for the xHCI host controller
|
|
found in MediaTek SoCs.
|
|
If unsure, say N.
|
|
|
|
config USB_XHCI_MVEBU
|
|
tristate "xHCI support for Marvell Armada 375/38x/37xx"
|
|
select USB_XHCI_PLATFORM
|
|
depends on HAS_IOMEM
|
|
depends on ARCH_MVEBU || COMPILE_TEST
|
|
help
|
|
Say 'Y' to enable the support for the xHCI host controller
|
|
found in Marvell Armada 375/38x/37xx ARM SOCs.
|
|
|
|
config USB_XHCI_RCAR
|
|
tristate "xHCI support for Renesas R-Car SoCs"
|
|
depends on USB_XHCI_PLATFORM
|
|
depends on ARCH_RENESAS || COMPILE_TEST
|
|
help
|
|
Say 'Y' to enable the support for the xHCI host controller
|
|
found in Renesas R-Car ARM SoCs.
|
|
|
|
config USB_XHCI_TEGRA
|
|
tristate "xHCI support for NVIDIA Tegra SoCs"
|
|
depends on PHY_TEGRA_XUSB
|
|
depends on RESET_CONTROLLER
|
|
select FW_LOADER
|
|
help
|
|
Say 'Y' to enable the support for the xHCI host controller
|
|
found in NVIDIA Tegra124 and later SoCs.
|
|
|
|
endif # USB_XHCI_HCD
|
|
|
|
config USB_EHCI_BRCMSTB
|
|
tristate
|
|
|
|
config USB_BRCMSTB
|
|
tristate "Broadcom STB USB support"
|
|
depends on (ARCH_BRCMSTB && PHY_BRCM_USB) || COMPILE_TEST
|
|
select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
|
|
select USB_EHCI_BRCMSTB if USB_EHCI_HCD
|
|
select USB_XHCI_PLATFORM if USB_XHCI_HCD
|
|
help
|
|
Enables support for XHCI, EHCI and OHCI host controllers
|
|
found in Broadcom STB SoC's.
|
|
|
|
To compile these drivers as modules, choose M here: the
|
|
modules will be called ohci-platform.ko, ehci-brcm.ko and
|
|
xhci-plat-hcd.ko
|
|
|
|
Disabling this will keep the controllers and corresponding
|
|
PHYs powered down.
|
|
|
|
config USB_EHCI_HCD
|
|
tristate "EHCI HCD (USB 2.0) support"
|
|
depends on HAS_DMA && HAS_IOMEM
|
|
help
|
|
The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
|
|
"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
|
|
If your USB host controller supports USB 2.0, you will likely want to
|
|
configure this Host Controller Driver.
|
|
|
|
EHCI controllers are packaged with "companion" host controllers (OHCI
|
|
or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
|
|
will connect to EHCI if the device is high speed, otherwise they
|
|
connect to a companion controller. If you configure EHCI, you should
|
|
probably configure the OHCI (for NEC and some other vendors) USB Host
|
|
Controller Driver or UHCI (for Via motherboards) Host Controller
|
|
Driver too.
|
|
|
|
You may want to read <file:Documentation/usb/ehci.rst>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ehci-hcd.
|
|
|
|
config USB_EHCI_ROOT_HUB_TT
|
|
bool "Root Hub Transaction Translators"
|
|
depends on USB_EHCI_HCD
|
|
help
|
|
Some EHCI chips have vendor-specific extensions to integrate
|
|
transaction translators, so that no OHCI or UHCI companion
|
|
controller is needed. It's safe to say "y" even if your
|
|
controller doesn't support this feature.
|
|
|
|
This supports the EHCI implementation that's originally
|
|
from ARC, and has since changed hands a few times.
|
|
|
|
config USB_EHCI_TT_NEWSCHED
|
|
bool "Improved Transaction Translator scheduling"
|
|
depends on USB_EHCI_HCD
|
|
default y
|
|
help
|
|
This changes the periodic scheduling code to fill more of the low
|
|
and full speed bandwidth available from the Transaction Translator
|
|
(TT) in USB 2.0 hubs. Without this, only one transfer will be
|
|
issued in each microframe, significantly reducing the number of
|
|
periodic low/fullspeed transfers possible.
|
|
|
|
If you have multiple periodic low/fullspeed devices connected to a
|
|
highspeed USB hub which is connected to a highspeed USB Host
|
|
Controller, and some of those devices will not work correctly
|
|
(possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
|
|
you have only one such device and it doesn't work, you could try
|
|
saying N.
|
|
|
|
If unsure, say Y.
|
|
|
|
if USB_EHCI_HCD
|
|
|
|
config USB_EHCI_PCI
|
|
tristate
|
|
depends on USB_PCI
|
|
default y
|
|
|
|
config XPS_USB_HCD_XILINX
|
|
bool "Use Xilinx usb host EHCI controller core"
|
|
depends on (PPC32 || MICROBLAZE)
|
|
select USB_EHCI_BIG_ENDIAN_DESC
|
|
select USB_EHCI_BIG_ENDIAN_MMIO
|
|
help
|
|
Xilinx xps USB host controller core is EHCI compliant and has
|
|
transaction translator built-in. It can be configured to either
|
|
support both high speed and full speed devices, or high speed
|
|
devices only.
|
|
|
|
config USB_EHCI_FSL
|
|
tristate "Support for Freescale on-chip EHCI USB controller"
|
|
select USB_EHCI_ROOT_HUB_TT
|
|
help
|
|
Variation of ARC USB block used in some Freescale chips.
|
|
|
|
config USB_EHCI_HCD_NPCM7XX
|
|
tristate "Support for Nuvoton NPCM7XX on-chip EHCI USB controller"
|
|
depends on (USB_EHCI_HCD && ARCH_NPCM7XX) || COMPILE_TEST
|
|
default y if (USB_EHCI_HCD && ARCH_NPCM7XX)
|
|
help
|
|
Enables support for the on-chip EHCI controller on
|
|
Nuvoton NPCM7XX chips.
|
|
|
|
config USB_EHCI_HCD_OMAP
|
|
tristate "EHCI support for OMAP3 and later chips"
|
|
depends on ARCH_OMAP
|
|
depends on NOP_USB_XCEIV
|
|
default y
|
|
help
|
|
Enables support for the on-chip EHCI controller on
|
|
OMAP3 and later chips.
|
|
|
|
config USB_EHCI_HCD_ORION
|
|
tristate "Support for Marvell EBU on-chip EHCI USB controller"
|
|
depends on USB_EHCI_HCD && (PLAT_ORION || ARCH_MVEBU || COMPILE_TEST)
|
|
default y if (PLAT_ORION || ARCH_MVEBU)
|
|
help
|
|
Enables support for the on-chip EHCI controller on Marvell's
|
|
embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
|
|
Armada 370. This is different from the EHCI implementation
|
|
on Marvell's mobile PXA and MMP SoC, see "EHCI support for
|
|
Marvell PXA/MMP USB controller" for those.
|
|
|
|
config USB_EHCI_HCD_SPEAR
|
|
tristate "Support for ST SPEAr on-chip EHCI USB controller"
|
|
depends on USB_EHCI_HCD && (PLAT_SPEAR || COMPILE_TEST)
|
|
default y if PLAT_SPEAR
|
|
help
|
|
Enables support for the on-chip EHCI controller on
|
|
ST SPEAr chips.
|
|
|
|
config USB_EHCI_HCD_STI
|
|
tristate "Support for ST STiHxxx on-chip EHCI USB controller"
|
|
depends on (ARCH_STI || COMPILE_TEST) && OF
|
|
select GENERIC_PHY
|
|
select USB_EHCI_HCD_PLATFORM
|
|
help
|
|
Enable support for the on-chip EHCI controller found on
|
|
STMicroelectronics consumer electronics SoC's.
|
|
|
|
config USB_EHCI_HCD_AT91
|
|
tristate "Support for Atmel on-chip EHCI USB controller"
|
|
depends on USB_EHCI_HCD && (ARCH_AT91 || COMPILE_TEST)
|
|
default y if ARCH_AT91
|
|
help
|
|
Enables support for the on-chip EHCI controller on
|
|
Atmel chips.
|
|
|
|
config USB_EHCI_TEGRA
|
|
tristate "NVIDIA Tegra HCD support"
|
|
depends on ARCH_TEGRA
|
|
select USB_CHIPIDEA
|
|
select USB_CHIPIDEA_HOST
|
|
select USB_CHIPIDEA_TEGRA
|
|
select USB_GADGET
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_CHIPIDEA_TEGRA instead.
|
|
|
|
Enable support for the internal USB Host Controllers
|
|
found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
|
|
|
|
config USB_EHCI_HCD_PPC_OF
|
|
bool "EHCI support for PPC USB controller on OF platform bus"
|
|
depends on PPC
|
|
default y
|
|
help
|
|
Enables support for the USB controller present on the PowerPC
|
|
OpenFirmware platform bus.
|
|
|
|
config USB_EHCI_SH
|
|
bool "EHCI support for SuperH USB controller"
|
|
depends on SUPERH || COMPILE_TEST
|
|
help
|
|
Enables support for the on-chip EHCI controller on the SuperH.
|
|
If you use the PCI EHCI controller, this option is not necessary.
|
|
|
|
config USB_EHCI_EXYNOS
|
|
tristate "EHCI support for Samsung S5P/Exynos SoC Series"
|
|
depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
|
|
help
|
|
Enable support for the Samsung S5Pv210 and Exynos SOC's on-chip EHCI
|
|
controller.
|
|
|
|
config USB_EHCI_MV
|
|
tristate "EHCI support for Marvell PXA/MMP USB controller"
|
|
depends on ARCH_PXA || ARCH_MMP || COMPILE_TEST
|
|
select USB_EHCI_ROOT_HUB_TT
|
|
help
|
|
Enables support for Marvell (including PXA and MMP series) on-chip
|
|
USB SPH and OTG controller. SPH is a single port host, and it can
|
|
only be EHCI host. OTG is controller that can switch to host mode.
|
|
Note that this driver will not work on Marvell's other EHCI
|
|
controller used by the EBU-type SoCs including Orion, Kirkwood,
|
|
Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
|
|
on-chip EHCI USB controller" for those.
|
|
|
|
config USB_CNS3XXX_EHCI
|
|
bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
|
|
depends on ARCH_CNS3XXX || COMPILE_TEST
|
|
select USB_EHCI_HCD_PLATFORM
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_EHCI_HCD_PLATFORM instead.
|
|
|
|
Enable support for the CNS3XXX SOC's on-chip EHCI controller.
|
|
It is needed for high-speed (480Mbit/sec) USB 2.0 device
|
|
support.
|
|
|
|
config USB_EHCI_HCD_PLATFORM
|
|
tristate "Generic EHCI driver for a platform device"
|
|
help
|
|
Adds an EHCI host driver for a generic platform device, which
|
|
provides a memory space and an irq.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_OCTEON_EHCI
|
|
bool "Octeon on-chip EHCI support (DEPRECATED)"
|
|
depends on CAVIUM_OCTEON_SOC
|
|
select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
|
|
select USB_EHCI_HCD_PLATFORM
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_EHCI_HCD_PLATFORM instead.
|
|
|
|
Enable support for the Octeon II SOC's on-chip EHCI
|
|
controller. It is needed for high-speed (480Mbit/sec)
|
|
USB 2.0 device support. All CN6XXX based chips with USB are
|
|
supported.
|
|
|
|
endif # USB_EHCI_HCD
|
|
|
|
config USB_OXU210HP_HCD
|
|
tristate "OXU210HP HCD support"
|
|
depends on HAS_IOMEM
|
|
help
|
|
The OXU210HP is an USB host/OTG/device controller. Enable this
|
|
option if your board has this chip. If unsure, say N.
|
|
|
|
This driver does not support isochronous transfers and doesn't
|
|
implement OTG nor USB device controllers.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called oxu210hp-hcd.
|
|
|
|
config USB_ISP116X_HCD
|
|
tristate "ISP116X HCD support"
|
|
depends on HAS_IOMEM
|
|
help
|
|
The ISP1160 and ISP1161 chips are USB host controllers. Enable this
|
|
option if your board has this chip. If unsure, say N.
|
|
|
|
This driver does not support isochronous transfers.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called isp116x-hcd.
|
|
|
|
config USB_ISP1362_HCD
|
|
tristate "ISP1362 HCD support"
|
|
depends on HAS_IOMEM
|
|
depends on COMPILE_TEST # nothing uses this
|
|
help
|
|
Supports the Philips ISP1362 chip as a host controller
|
|
|
|
This driver does not support isochronous transfers.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called isp1362-hcd.
|
|
|
|
config USB_FOTG210_HCD
|
|
tristate "FOTG210 HCD support"
|
|
depends on USB && HAS_DMA && HAS_IOMEM
|
|
help
|
|
Faraday FOTG210 is an OTG controller which can be configured as
|
|
an USB2.0 host. It is designed to meet USB2.0 EHCI specification
|
|
with minor modification.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called fotg210-hcd.
|
|
|
|
config USB_MAX3421_HCD
|
|
tristate "MAX3421 HCD (USB-over-SPI) support"
|
|
depends on USB && SPI
|
|
help
|
|
The Maxim MAX3421E chip supports standard USB 2.0-compliant
|
|
full-speed devices either in host or peripheral mode. This
|
|
driver supports the host-mode of the MAX3421E only.
|
|
|
|
To compile this driver as a module, choose M here: the module will
|
|
be called max3421-hcd.
|
|
|
|
config USB_OHCI_HCD
|
|
tristate "OHCI HCD (USB 1.1) support"
|
|
depends on HAS_DMA && HAS_IOMEM
|
|
help
|
|
The Open Host Controller Interface (OHCI) is a standard for accessing
|
|
USB 1.1 host controller hardware. It does more in hardware than Intel's
|
|
UHCI specification. If your USB host controller follows the OHCI spec,
|
|
say Y. On most non-x86 systems, and on x86 hardware that's not using a
|
|
USB controller from Intel or VIA, this is appropriate. If your host
|
|
controller doesn't use PCI, this is probably appropriate. For a PCI
|
|
based system where you're not sure, the "lspci -v" entry will list the
|
|
right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ohci-hcd.
|
|
|
|
if USB_OHCI_HCD
|
|
|
|
config USB_OHCI_HCD_OMAP1
|
|
tristate "OHCI support for OMAP1/2 chips"
|
|
depends on ARCH_OMAP1
|
|
depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
|
|
default y
|
|
help
|
|
Enables support for the OHCI controller on OMAP1/2 chips.
|
|
|
|
config USB_OHCI_HCD_SPEAR
|
|
tristate "Support for ST SPEAr on-chip OHCI USB controller"
|
|
depends on USB_OHCI_HCD && (PLAT_SPEAR || COMPILE_TEST)
|
|
default y if PLAT_SPEAR
|
|
help
|
|
Enables support for the on-chip OHCI controller on
|
|
ST SPEAr chips.
|
|
|
|
config USB_OHCI_HCD_STI
|
|
tristate "Support for ST STiHxxx on-chip OHCI USB controller"
|
|
depends on (ARCH_STI || COMPILE_TEST) && OF
|
|
select GENERIC_PHY
|
|
select USB_OHCI_HCD_PLATFORM
|
|
help
|
|
Enable support for the on-chip OHCI controller found on
|
|
STMicroelectronics consumer electronics SoC's.
|
|
|
|
config USB_OHCI_HCD_S3C2410
|
|
tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series"
|
|
depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX || COMPILE_TEST)
|
|
default y if (ARCH_S3C24XX || ARCH_S3C64XX)
|
|
help
|
|
Enables support for the on-chip OHCI controller on
|
|
S3C24xx/S3C64xx chips.
|
|
|
|
config USB_OHCI_HCD_LPC32XX
|
|
tristate "Support for LPC on-chip OHCI USB controller"
|
|
depends on USB_OHCI_HCD
|
|
depends on ARCH_LPC32XX || COMPILE_TEST
|
|
depends on USB_ISP1301
|
|
default y
|
|
help
|
|
Enables support for the on-chip OHCI controller on
|
|
NXP chips.
|
|
|
|
config USB_OHCI_HCD_PXA27X
|
|
tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
|
|
depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
|
|
default y
|
|
help
|
|
Enables support for the on-chip OHCI controller on
|
|
PXA27x/PXA3xx chips.
|
|
|
|
config USB_OHCI_HCD_AT91
|
|
tristate "Support for Atmel on-chip OHCI USB controller"
|
|
depends on USB_OHCI_HCD && (ARCH_AT91 || COMPILE_TEST) && OF
|
|
default y if ARCH_AT91
|
|
help
|
|
Enables support for the on-chip OHCI controller on
|
|
Atmel chips.
|
|
|
|
config USB_OHCI_HCD_OMAP3
|
|
tristate "OHCI support for OMAP3 and later chips"
|
|
depends on ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5 || COMPILE_TEST
|
|
select USB_OHCI_HCD_PLATFORM
|
|
default y if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_OHCI_HCD_PLATFORM instead.
|
|
|
|
Enables support for the on-chip OHCI controller on
|
|
OMAP3 and later chips.
|
|
|
|
config USB_OHCI_HCD_DAVINCI
|
|
tristate "OHCI support for TI DaVinci DA8xx"
|
|
depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
|
|
depends on USB_OHCI_HCD
|
|
select PHY_DA8XX_USB
|
|
default y if ARCH_DAVINCI_DA8XX
|
|
help
|
|
Enables support for the DaVinci DA8xx integrated OHCI
|
|
controller. This driver cannot currently be a loadable
|
|
module because it lacks a proper PHY abstraction.
|
|
|
|
config USB_OHCI_HCD_PPC_OF_BE
|
|
bool "OHCI support for OF platform bus (big endian)"
|
|
depends on PPC
|
|
select USB_OHCI_BIG_ENDIAN_DESC
|
|
select USB_OHCI_BIG_ENDIAN_MMIO
|
|
help
|
|
Enables support for big-endian USB controllers present on the
|
|
OpenFirmware platform bus.
|
|
|
|
config USB_OHCI_HCD_PPC_OF_LE
|
|
bool "OHCI support for OF platform bus (little endian)"
|
|
depends on PPC
|
|
select USB_OHCI_LITTLE_ENDIAN
|
|
help
|
|
Enables support for little-endian USB controllers present on the
|
|
OpenFirmware platform bus.
|
|
|
|
config USB_OHCI_HCD_PPC_OF
|
|
bool
|
|
depends on PPC
|
|
default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
|
|
|
|
config USB_OHCI_HCD_PCI
|
|
tristate "OHCI support for PCI-bus USB controllers"
|
|
depends on USB_PCI
|
|
default y
|
|
select USB_OHCI_LITTLE_ENDIAN
|
|
help
|
|
Enables support for PCI-bus plug-in USB controller cards.
|
|
If unsure, say Y.
|
|
|
|
config USB_OHCI_HCD_SSB
|
|
bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
|
|
depends on (SSB = y || SSB = USB_OHCI_HCD)
|
|
select USB_HCD_SSB
|
|
select USB_OHCI_HCD_PLATFORM
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
|
|
|
|
Support for the Sonics Silicon Backplane (SSB) attached
|
|
Broadcom USB OHCI core.
|
|
|
|
This device is present in some embedded devices with
|
|
Broadcom based SSB bus.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_OHCI_SH
|
|
bool "OHCI support for SuperH USB controller (DEPRECATED)"
|
|
depends on SUPERH || COMPILE_TEST
|
|
select USB_OHCI_HCD_PLATFORM
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_OHCI_HCD_PLATFORM instead.
|
|
|
|
Enables support for the on-chip OHCI controller on the SuperH.
|
|
If you use the PCI OHCI controller, this option is not necessary.
|
|
|
|
config USB_OHCI_EXYNOS
|
|
tristate "OHCI support for Samsung S5P/Exynos SoC Series"
|
|
depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
|
|
help
|
|
Enable support for the Samsung S5Pv210 and Exynos SOC's on-chip OHCI
|
|
controller.
|
|
|
|
config USB_CNS3XXX_OHCI
|
|
bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
|
|
depends on ARCH_CNS3XXX || COMPILE_TEST
|
|
select USB_OHCI_HCD_PLATFORM
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_OHCI_HCD_PLATFORM instead.
|
|
|
|
Enable support for the CNS3XXX SOC's on-chip OHCI controller.
|
|
It is needed for low-speed USB 1.0 device support.
|
|
|
|
config USB_OHCI_HCD_PLATFORM
|
|
tristate "Generic OHCI driver for a platform device"
|
|
help
|
|
Adds an OHCI host driver for a generic platform device, which
|
|
provides a memory space and an irq.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_OCTEON_OHCI
|
|
bool "Octeon on-chip OHCI support (DEPRECATED)"
|
|
depends on CAVIUM_OCTEON_SOC
|
|
default USB_OCTEON_EHCI
|
|
select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
|
|
select USB_OHCI_LITTLE_ENDIAN
|
|
select USB_OHCI_HCD_PLATFORM
|
|
help
|
|
This option is deprecated now and the driver was removed, use
|
|
USB_OHCI_HCD_PLATFORM instead.
|
|
|
|
Enable support for the Octeon II SOC's on-chip OHCI
|
|
controller. It is needed for low-speed USB 1.0 device
|
|
support. All CN6XXX based chips with USB are supported.
|
|
|
|
endif # USB_OHCI_HCD
|
|
|
|
config USB_UHCI_HCD
|
|
tristate "UHCI HCD (most Intel and VIA) support"
|
|
depends on USB_PCI || USB_UHCI_SUPPORT_NON_PCI_HC
|
|
help
|
|
The Universal Host Controller Interface is a standard by Intel for
|
|
accessing the USB hardware in the PC (which is also called the USB
|
|
host controller). If your USB host controller conforms to this
|
|
standard, you may want to say Y, but see below. All recent boards
|
|
with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
|
|
i810, i820) conform to this standard. Also all VIA PCI chipsets
|
|
(like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
|
|
133) and LEON/GRLIB SoCs with the GRUSBHC controller.
|
|
If unsure, say Y.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called uhci-hcd.
|
|
|
|
config USB_UHCI_SUPPORT_NON_PCI_HC
|
|
bool
|
|
default y if (SPARC_LEON || USB_UHCI_PLATFORM)
|
|
|
|
config USB_UHCI_PLATFORM
|
|
bool
|
|
default y if (ARCH_VT8500 || ARCH_ASPEED)
|
|
|
|
config USB_UHCI_ASPEED
|
|
bool
|
|
default y if ARCH_ASPEED
|
|
|
|
config USB_FHCI_HCD
|
|
tristate "Freescale QE USB Host Controller support"
|
|
depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
|
|
select FSL_GTM
|
|
select QE_USB
|
|
help
|
|
This driver enables support for Freescale QE USB Host Controller
|
|
(as found on MPC8360 and MPC8323 processors), the driver supports
|
|
Full and Low Speed USB.
|
|
|
|
config FHCI_DEBUG
|
|
bool "Freescale QE USB Host Controller debug support"
|
|
depends on USB_FHCI_HCD && DEBUG_FS
|
|
help
|
|
Say "y" to see some FHCI debug information and statistics
|
|
through debugfs.
|
|
|
|
config USB_U132_HCD
|
|
tristate "Elan U132 Adapter Host Controller"
|
|
depends on USB_FTDI_ELAN
|
|
help
|
|
The U132 adapter is a USB to CardBus adapter specifically designed
|
|
for PC cards that contain an OHCI host controller. Typical PC cards
|
|
are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
|
|
adapter will *NOT* work with PC cards that do not contain an OHCI
|
|
controller.
|
|
|
|
For those PC cards that contain multiple OHCI controllers only the
|
|
first one is used.
|
|
|
|
The driver consists of two modules, the "ftdi-elan" module is a
|
|
USB client driver that interfaces to the FTDI chip within ELAN's
|
|
USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
|
|
controller driver that talks to the OHCI controller within the
|
|
CardBus cards that are inserted in the U132 adapter.
|
|
|
|
This driver has been tested with a CardBus OHCI USB adapter, and
|
|
worked with a USB PEN Drive inserted into the first USB port of
|
|
the PCCARD. A rather pointless thing to do, but useful for testing.
|
|
|
|
It is safe to say M here.
|
|
|
|
See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
|
|
|
|
config USB_SL811_HCD
|
|
tristate "SL811HS HCD support"
|
|
depends on HAS_IOMEM
|
|
help
|
|
The SL811HS is a single-port USB controller that supports either
|
|
host side or peripheral side roles. Enable this option if your
|
|
board has this chip, and you want to use it as a host controller.
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sl811-hcd.
|
|
|
|
config USB_SL811_HCD_ISO
|
|
bool "partial ISO support"
|
|
depends on USB_SL811_HCD
|
|
help
|
|
The driver doesn't support iso_frame_desc (yet), but for some simple
|
|
devices that just queue one ISO frame per URB, then ISO transfers
|
|
"should" work using the normal urb status fields.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_SL811_CS
|
|
tristate "CF/PCMCIA support for SL811HS HCD"
|
|
depends on USB_SL811_HCD && PCMCIA
|
|
help
|
|
Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
|
|
REX-CFU1U CF card (often used with PDAs). If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called "sl811_cs".
|
|
|
|
config USB_R8A66597_HCD
|
|
tristate "R8A66597 HCD support"
|
|
depends on HAS_IOMEM
|
|
help
|
|
The R8A66597 is a USB 2.0 host and peripheral controller.
|
|
|
|
Enable this option if your board has this chip, and you want
|
|
to use it as a host controller. If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called r8a66597-hcd.
|
|
|
|
config USB_RENESAS_USBHS_HCD
|
|
tristate "Renesas USBHS HCD support"
|
|
depends on USB_RENESAS_USBHS
|
|
help
|
|
The Renesas USBHS is a USB 2.0 host and peripheral controller.
|
|
|
|
Enable this option if your board has this chip, and you want
|
|
to use it as a host controller. If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called renesas-usbhs.
|
|
|
|
config USB_HCD_BCMA
|
|
tristate "BCMA usb host driver"
|
|
depends on BCMA
|
|
select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
|
|
select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
|
|
help
|
|
Enable support for the EHCI and OCHI host controller on an bcma bus.
|
|
It converts the bcma driver into two platform device drivers
|
|
for ehci and ohci.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_HCD_SSB
|
|
tristate "SSB usb host driver"
|
|
depends on SSB
|
|
select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
|
|
select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
|
|
help
|
|
Enable support for the EHCI and OCHI host controller on an bcma bus.
|
|
It converts the bcma driver into two platform device drivers
|
|
for ehci and ohci.
|
|
|
|
If unsure, say N.
|
|
|
|
config USB_HCD_TEST_MODE
|
|
bool "HCD test mode support"
|
|
help
|
|
Say 'Y' to enable additional software test modes that may be
|
|
supported by the host controller drivers.
|
|
|
|
One such test mode is the Embedded High-speed Host Electrical Test
|
|
(EHSET) for EHCI host controller hardware, specifically the "Single
|
|
Step Set Feature" test. Typically this will be enabled for On-the-Go
|
|
or embedded hosts that need to undergo USB-IF compliance testing with
|
|
the aid of special testing hardware. In the future, this may expand
|
|
to include other tests that require support from a HCD driver.
|
|
|
|
This option is of interest only to developers who need to validate
|
|
their USB hardware designs. It is not needed for normal use. If
|
|
unsure, say N.
|
|
|
|
config USB_XEN_HCD
|
|
tristate "Xen usb virtual host driver"
|
|
depends on XEN
|
|
select XEN_XENBUS_FRONTEND
|
|
help
|
|
The Xen usb virtual host driver serves as a frontend driver enabling
|
|
a Xen guest system to access USB Devices passed through to the guest
|
|
by the Xen host (usually Dom0).
|
|
Only needed if the kernel is running in a Xen guest and generic
|
|
access to a USB device is needed.
|