OpenCloudOS-Kernel/drivers/net/ethernet/moxa/moxart_ether.h

332 lines
10 KiB
C

/* MOXA ART Ethernet (RTL8201CP) driver.
*
* Copyright (C) 2013 Jonas Jensen
*
* Jonas Jensen <jonas.jensen@gmail.com>
*
* Based on code from
* Moxa Technology Co., Ltd. <www.moxa.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#ifndef _MOXART_ETHERNET_H
#define _MOXART_ETHERNET_H
#define TX_REG_OFFSET_DESC0 0
#define TX_REG_OFFSET_DESC1 4
#define TX_REG_OFFSET_DESC2 8
#define TX_REG_DESC_SIZE 16
#define RX_REG_OFFSET_DESC0 0
#define RX_REG_OFFSET_DESC1 4
#define RX_REG_OFFSET_DESC2 8
#define RX_REG_DESC_SIZE 16
#define TX_DESC0_PKT_LATE_COL 0x1 /* abort, late collision */
#define TX_DESC0_RX_PKT_EXS_COL 0x2 /* abort, >16 collisions */
#define TX_DESC0_DMA_OWN 0x80000000 /* owned by controller */
#define TX_DESC1_BUF_SIZE_MASK 0x7ff
#define TX_DESC1_LTS 0x8000000 /* last TX packet */
#define TX_DESC1_FTS 0x10000000 /* first TX packet */
#define TX_DESC1_FIFO_COMPLETE 0x20000000
#define TX_DESC1_INTR_COMPLETE 0x40000000
#define TX_DESC1_END 0x80000000
#define TX_DESC2_ADDRESS_PHYS 0
#define TX_DESC2_ADDRESS_VIRT 4
#define RX_DESC0_FRAME_LEN 0
#define RX_DESC0_FRAME_LEN_MASK 0x7FF
#define RX_DESC0_MULTICAST 0x10000
#define RX_DESC0_BROADCAST 0x20000
#define RX_DESC0_ERR 0x40000
#define RX_DESC0_CRC_ERR 0x80000
#define RX_DESC0_FTL 0x100000
#define RX_DESC0_RUNT 0x200000 /* packet less than 64 bytes */
#define RX_DESC0_ODD_NB 0x400000 /* receive odd nibbles */
#define RX_DESC0_LRS 0x10000000 /* last receive segment */
#define RX_DESC0_FRS 0x20000000 /* first receive segment */
#define RX_DESC0_DMA_OWN 0x80000000
#define RX_DESC1_BUF_SIZE_MASK 0x7FF
#define RX_DESC1_END 0x80000000
#define RX_DESC2_ADDRESS_PHYS 0
#define RX_DESC2_ADDRESS_VIRT 4
#define TX_DESC_NUM 64
#define TX_DESC_NUM_MASK (TX_DESC_NUM - 1)
#define TX_NEXT(N) (((N) + 1) & (TX_DESC_NUM_MASK))
#define TX_BUF_SIZE 1600
#define TX_BUF_SIZE_MAX (TX_DESC1_BUF_SIZE_MASK + 1)
#define TX_WAKE_THRESHOLD 16
#define RX_DESC_NUM 64
#define RX_DESC_NUM_MASK (RX_DESC_NUM - 1)
#define RX_NEXT(N) (((N) + 1) & (RX_DESC_NUM_MASK))
#define RX_BUF_SIZE 1600
#define RX_BUF_SIZE_MAX (RX_DESC1_BUF_SIZE_MASK + 1)
#define REG_INTERRUPT_STATUS 0
#define REG_INTERRUPT_MASK 4
#define REG_MAC_MS_ADDRESS 8
#define REG_MAC_LS_ADDRESS 12
#define REG_MCAST_HASH_TABLE0 16
#define REG_MCAST_HASH_TABLE1 20
#define REG_TX_POLL_DEMAND 24
#define REG_RX_POLL_DEMAND 28
#define REG_TXR_BASE_ADDRESS 32
#define REG_RXR_BASE_ADDRESS 36
#define REG_INT_TIMER_CTRL 40
#define REG_APOLL_TIMER_CTRL 44
#define REG_DMA_BLEN_CTRL 48
#define REG_RESERVED1 52
#define REG_MAC_CTRL 136
#define REG_MAC_STATUS 140
#define REG_PHY_CTRL 144
#define REG_PHY_WRITE_DATA 148
#define REG_FLOW_CTRL 152
#define REG_BACK_PRESSURE 156
#define REG_RESERVED2 160
#define REG_TEST_SEED 196
#define REG_DMA_FIFO_STATE 200
#define REG_TEST_MODE 204
#define REG_RESERVED3 208
#define REG_TX_COL_COUNTER 212
#define REG_RPF_AEP_COUNTER 216
#define REG_XM_PG_COUNTER 220
#define REG_RUNT_TLC_COUNTER 224
#define REG_CRC_FTL_COUNTER 228
#define REG_RLC_RCC_COUNTER 232
#define REG_BROC_COUNTER 236
#define REG_MULCA_COUNTER 240
#define REG_RP_COUNTER 244
#define REG_XP_COUNTER 248
#define REG_PHY_CTRL_OFFSET 0x0
#define REG_PHY_STATUS 0x1
#define REG_PHY_ID1 0x2
#define REG_PHY_ID2 0x3
#define REG_PHY_ANA 0x4
#define REG_PHY_ANLPAR 0x5
#define REG_PHY_ANE 0x6
#define REG_PHY_ECTRL1 0x10
#define REG_PHY_QPDS 0x11
#define REG_PHY_10BOP 0x12
#define REG_PHY_ECTRL2 0x13
#define REG_PHY_FTMAC100_WRITE 0x8000000
#define REG_PHY_FTMAC100_READ 0x4000000
/* REG_INTERRUPT_STATUS */
#define RPKT_FINISH BIT(0) /* DMA data received */
#define NORXBUF BIT(1) /* receive buffer unavailable */
#define XPKT_FINISH BIT(2) /* DMA moved data to TX FIFO */
#define NOTXBUF BIT(3) /* transmit buffer unavailable */
#define XPKT_OK_INT_STS BIT(4) /* transmit to ethernet success */
#define XPKT_LOST_INT_STS BIT(5) /* transmit ethernet lost (collision) */
#define RPKT_SAV BIT(6) /* FIFO receive success */
#define RPKT_LOST_INT_STS BIT(7) /* FIFO full, receive failed */
#define AHB_ERR BIT(8) /* AHB error */
#define PHYSTS_CHG BIT(9) /* PHY link status change */
/* REG_INTERRUPT_MASK */
#define RPKT_FINISH_M BIT(0)
#define NORXBUF_M BIT(1)
#define XPKT_FINISH_M BIT(2)
#define NOTXBUF_M BIT(3)
#define XPKT_OK_M BIT(4)
#define XPKT_LOST_M BIT(5)
#define RPKT_SAV_M BIT(6)
#define RPKT_LOST_M BIT(7)
#define AHB_ERR_M BIT(8)
#define PHYSTS_CHG_M BIT(9)
/* REG_MAC_MS_ADDRESS */
#define MAC_MADR_MASK 0xffff /* 2 MSB MAC address */
/* REG_INT_TIMER_CTRL */
#define TXINT_TIME_SEL BIT(15) /* TX cycle time period */
#define TXINT_THR_MASK 0x7000
#define TXINT_CNT_MASK 0xf00
#define RXINT_TIME_SEL BIT(7) /* RX cycle time period */
#define RXINT_THR_MASK 0x70
#define RXINT_CNT_MASK 0xF
/* REG_APOLL_TIMER_CTRL */
#define TXPOLL_TIME_SEL BIT(12) /* TX poll time period */
#define TXPOLL_CNT_MASK 0xf00
#define TXPOLL_CNT_SHIFT_BIT 8
#define RXPOLL_TIME_SEL BIT(4) /* RX poll time period */
#define RXPOLL_CNT_MASK 0xF
#define RXPOLL_CNT_SHIFT_BIT 0
/* REG_DMA_BLEN_CTRL */
#define RX_THR_EN BIT(9) /* RX FIFO threshold arbitration */
#define RXFIFO_HTHR_MASK 0x1c0
#define RXFIFO_LTHR_MASK 0x38
#define INCR16_EN BIT(2) /* AHB bus INCR16 burst command */
#define INCR8_EN BIT(1) /* AHB bus INCR8 burst command */
#define INCR4_EN BIT(0) /* AHB bus INCR4 burst command */
/* REG_MAC_CTRL */
#define RX_BROADPKT BIT(17) /* receive broadcast packets */
#define RX_MULTIPKT BIT(16) /* receive all multicast packets */
#define FULLDUP BIT(15) /* full duplex */
#define CRC_APD BIT(14) /* append CRC to transmitted packet */
#define RCV_ALL BIT(12) /* ignore incoming packet destination */
#define RX_FTL BIT(11) /* accept packets larger than 1518 B */
#define RX_RUNT BIT(10) /* accept packets smaller than 64 B */
#define HT_MULTI_EN BIT(9) /* accept on hash and mcast pass */
#define RCV_EN BIT(8) /* receiver enable */
#define ENRX_IN_HALFTX BIT(6) /* enable receive in half duplex mode */
#define XMT_EN BIT(5) /* transmit enable */
#define CRC_DIS BIT(4) /* disable CRC check when receiving */
#define LOOP_EN BIT(3) /* internal loop-back */
#define SW_RST BIT(2) /* software reset, last 64 AHB clocks */
#define RDMA_EN BIT(1) /* enable receive DMA chan */
#define XDMA_EN BIT(0) /* enable transmit DMA chan */
/* REG_MAC_STATUS */
#define COL_EXCEED BIT(11) /* more than 16 collisions */
#define LATE_COL BIT(10) /* transmit late collision detected */
#define XPKT_LOST BIT(9) /* transmit to ethernet lost */
#define XPKT_OK BIT(8) /* transmit to ethernet success */
#define RUNT_MAC_STS BIT(7) /* receive runt detected */
#define FTL_MAC_STS BIT(6) /* receive frame too long detected */
#define CRC_ERR_MAC_STS BIT(5)
#define RPKT_LOST BIT(4) /* RX FIFO full, receive failed */
#define RPKT_SAVE BIT(3) /* RX FIFO receive success */
#define COL BIT(2) /* collision, incoming packet dropped */
#define MCPU_BROADCAST BIT(1)
#define MCPU_MULTICAST BIT(0)
/* REG_PHY_CTRL */
#define MIIWR BIT(27) /* init write sequence (auto cleared)*/
#define MIIRD BIT(26)
#define REGAD_MASK 0x3e00000
#define PHYAD_MASK 0x1f0000
#define MIIRDATA_MASK 0xffff
/* REG_PHY_WRITE_DATA */
#define MIIWDATA_MASK 0xffff
/* REG_FLOW_CTRL */
#define PAUSE_TIME_MASK 0xffff0000
#define FC_HIGH_MASK 0xf000
#define FC_LOW_MASK 0xf00
#define RX_PAUSE BIT(4) /* receive pause frame */
#define TX_PAUSED BIT(3) /* transmit pause due to receive */
#define FCTHR_EN BIT(2) /* enable threshold mode. */
#define TX_PAUSE BIT(1) /* transmit pause frame */
#define FC_EN BIT(0) /* flow control mode enable */
/* REG_BACK_PRESSURE */
#define BACKP_LOW_MASK 0xf00
#define BACKP_JAM_LEN_MASK 0xf0
#define BACKP_MODE BIT(1) /* address mode */
#define BACKP_ENABLE BIT(0)
/* REG_TEST_SEED */
#define TEST_SEED_MASK 0x3fff
/* REG_DMA_FIFO_STATE */
#define TX_DMA_REQUEST BIT(31)
#define RX_DMA_REQUEST BIT(30)
#define TX_DMA_GRANT BIT(29)
#define RX_DMA_GRANT BIT(28)
#define TX_FIFO_EMPTY BIT(27)
#define RX_FIFO_EMPTY BIT(26)
#define TX_DMA2_SM_MASK 0x7000
#define TX_DMA1_SM_MASK 0xf00
#define RX_DMA2_SM_MASK 0x70
#define RX_DMA1_SM_MASK 0xF
/* REG_TEST_MODE */
#define SINGLE_PKT BIT(26) /* single packet mode */
#define PTIMER_TEST BIT(25) /* automatic polling timer test mode */
#define ITIMER_TEST BIT(24) /* interrupt timer test mode */
#define TEST_SEED_SELECT BIT(22)
#define SEED_SELECT BIT(21)
#define TEST_MODE BIT(20)
#define TEST_TIME_MASK 0xffc00
#define TEST_EXCEL_MASK 0x3e0
/* REG_TX_COL_COUNTER */
#define TX_MCOL_MASK 0xffff0000
#define TX_MCOL_SHIFT_BIT 16
#define TX_SCOL_MASK 0xffff
#define TX_SCOL_SHIFT_BIT 0
/* REG_RPF_AEP_COUNTER */
#define RPF_MASK 0xffff0000
#define RPF_SHIFT_BIT 16
#define AEP_MASK 0xffff
#define AEP_SHIFT_BIT 0
/* REG_XM_PG_COUNTER */
#define XM_MASK 0xffff0000
#define XM_SHIFT_BIT 16
#define PG_MASK 0xffff
#define PG_SHIFT_BIT 0
/* REG_RUNT_TLC_COUNTER */
#define RUNT_CNT_MASK 0xffff0000
#define RUNT_CNT_SHIFT_BIT 16
#define TLCC_MASK 0xffff
#define TLCC_SHIFT_BIT 0
/* REG_CRC_FTL_COUNTER */
#define CRCER_CNT_MASK 0xffff0000
#define CRCER_CNT_SHIFT_BIT 16
#define FTL_CNT_MASK 0xffff
#define FTL_CNT_SHIFT_BIT 0
/* REG_RLC_RCC_COUNTER */
#define RLC_MASK 0xffff0000
#define RLC_SHIFT_BIT 16
#define RCC_MASK 0xffff
#define RCC_SHIFT_BIT 0
/* REG_PHY_STATUS */
#define AN_COMPLETE 0x20
#define LINK_STATUS 0x4
struct moxart_mac_priv_t {
struct platform_device *pdev;
void __iomem *base;
unsigned int reg_maccr;
unsigned int reg_imr;
struct napi_struct napi;
struct net_device *ndev;
dma_addr_t rx_base;
dma_addr_t rx_mapping[RX_DESC_NUM];
void *rx_desc_base;
unsigned char *rx_buf_base;
unsigned char *rx_buf[RX_DESC_NUM];
unsigned int rx_head;
unsigned int rx_buf_size;
dma_addr_t tx_base;
dma_addr_t tx_mapping[TX_DESC_NUM];
void *tx_desc_base;
unsigned char *tx_buf_base;
unsigned char *tx_buf[RX_DESC_NUM];
unsigned int tx_head;
unsigned int tx_buf_size;
spinlock_t txlock;
unsigned int tx_len[TX_DESC_NUM];
struct sk_buff *tx_skb[TX_DESC_NUM];
unsigned int tx_tail;
};
#if TX_BUF_SIZE >= TX_BUF_SIZE_MAX
#error MOXA ART Ethernet device driver TX buffer is too large!
#endif
#if RX_BUF_SIZE >= RX_BUF_SIZE_MAX
#error MOXA ART Ethernet device driver RX buffer is too large!
#endif
#endif