221 lines
6.1 KiB
Plaintext
221 lines
6.1 KiB
Plaintext
(C)Copyright 1998-2000 SysKonnect,
|
|
===========================================================================
|
|
|
|
skfp.txt created 11-May-2000
|
|
|
|
Readme File for skfp.o v2.06
|
|
|
|
|
|
This file contains
|
|
(1) OVERVIEW
|
|
(2) SUPPORTED ADAPTERS
|
|
(3) GENERAL INFORMATION
|
|
(4) INSTALLATION
|
|
(5) INCLUSION OF THE ADAPTER IN SYSTEM START
|
|
(6) TROUBLESHOOTING
|
|
(7) FUNCTION OF THE ADAPTER LEDS
|
|
(8) HISTORY
|
|
|
|
===========================================================================
|
|
|
|
|
|
|
|
(1) OVERVIEW
|
|
============
|
|
|
|
This README explains how to use the driver 'skfp' for Linux with your
|
|
network adapter.
|
|
|
|
Chapter 2: Contains a list of all network adapters that are supported by
|
|
this driver.
|
|
|
|
Chapter 3: Gives some general information.
|
|
|
|
Chapter 4: Describes common problems and solutions.
|
|
|
|
Chapter 5: Shows the changed functionality of the adapter LEDs.
|
|
|
|
Chapter 6: History of development.
|
|
|
|
***
|
|
|
|
|
|
(2) SUPPORTED ADAPTERS
|
|
======================
|
|
|
|
The network driver 'skfp' supports the following network adapters:
|
|
SysKonnect adapters:
|
|
- SK-5521 (SK-NET FDDI-UP)
|
|
- SK-5522 (SK-NET FDDI-UP DAS)
|
|
- SK-5541 (SK-NET FDDI-FP)
|
|
- SK-5543 (SK-NET FDDI-LP)
|
|
- SK-5544 (SK-NET FDDI-LP DAS)
|
|
- SK-5821 (SK-NET FDDI-UP64)
|
|
- SK-5822 (SK-NET FDDI-UP64 DAS)
|
|
- SK-5841 (SK-NET FDDI-FP64)
|
|
- SK-5843 (SK-NET FDDI-LP64)
|
|
- SK-5844 (SK-NET FDDI-LP64 DAS)
|
|
Compaq adapters (not tested):
|
|
- Netelligent 100 FDDI DAS Fibre SC
|
|
- Netelligent 100 FDDI SAS Fibre SC
|
|
- Netelligent 100 FDDI DAS UTP
|
|
- Netelligent 100 FDDI SAS UTP
|
|
- Netelligent 100 FDDI SAS Fibre MIC
|
|
***
|
|
|
|
|
|
(3) GENERAL INFORMATION
|
|
=======================
|
|
|
|
From v2.01 on, the driver is integrated in the linux kernel sources.
|
|
Therefor, the installation is the same as for any other adapter
|
|
supported by the kernel.
|
|
Refer to the manual of your distribution about the installation
|
|
of network adapters.
|
|
Makes my life much easier :-)
|
|
***
|
|
|
|
|
|
(4) TROUBLESHOOTING
|
|
===================
|
|
|
|
If you run into problems during installation, check those items:
|
|
|
|
Problem: The FDDI adapter can not be found by the driver.
|
|
Reason: Look in /proc/pci for the following entry:
|
|
'FDDI network controller: SysKonnect SK-FDDI-PCI ...'
|
|
If this entry exists, then the FDDI adapter has been
|
|
found by the system and should be able to be used.
|
|
If this entry does not exist or if the file '/proc/pci'
|
|
is not there, then you may have a hardware problem or PCI
|
|
support may not be enabled in your kernel.
|
|
The adapter can be checked using the diagnostic program
|
|
which is available from the SysKonnect web site:
|
|
www.syskonnect.de
|
|
Some COMPAQ machines have a problem with PCI under
|
|
Linux. This is described in the 'PCI howto' document
|
|
(included in some distributions or available from the
|
|
www, e.g. at 'www.linux.org') and no workaround is available.
|
|
|
|
Problem: You want to use your computer as a router between
|
|
multiple IP subnetworks (using multiple adapters), but
|
|
you can not reach computers in other subnetworks.
|
|
Reason: Either the router's kernel is not configured for IP
|
|
forwarding or there is a problem with the routing table
|
|
and gateway configuration in at least one of the
|
|
computers.
|
|
|
|
If your problem is not listed here, please contact our
|
|
technical support for help.
|
|
You can send email to:
|
|
linux@syskonnect.de
|
|
When contacting our technical support,
|
|
please ensure that the following information is available:
|
|
- System Manufacturer and Model
|
|
- Boards in your system
|
|
- Distribution
|
|
- Kernel version
|
|
|
|
***
|
|
|
|
|
|
(5) FUNCTION OF THE ADAPTER LEDS
|
|
================================
|
|
|
|
The functionality of the LED's on the FDDI network adapters was
|
|
changed in SMT version v2.82. With this new SMT version, the yellow
|
|
LED works as a ring operational indicator. An active yellow LED
|
|
indicates that the ring is down. The green LED on the adapter now
|
|
works as a link indicator where an active GREEN LED indicates that
|
|
the respective port has a physical connection.
|
|
|
|
With versions of SMT prior to v2.82 a ring up was indicated if the
|
|
yellow LED was off while the green LED(s) showed the connection
|
|
status of the adapter. During a ring down the green LED was off and
|
|
the yellow LED was on.
|
|
|
|
All implementations indicate that a driver is not loaded if
|
|
all LEDs are off.
|
|
|
|
***
|
|
|
|
|
|
(6) HISTORY
|
|
===========
|
|
|
|
v2.06 (20000511) (In-Kernel version)
|
|
New features:
|
|
- 64 bit support
|
|
- new pci dma interface
|
|
- in kernel 2.3.99
|
|
|
|
v2.05 (20000217) (In-Kernel version)
|
|
New features:
|
|
- Changes for 2.3.45 kernel
|
|
|
|
v2.04 (20000207) (Standalone version)
|
|
New features:
|
|
- Added rx/tx byte counter
|
|
|
|
v2.03 (20000111) (Standalone version)
|
|
Problems fixed:
|
|
- Fixed printk statements from v2.02
|
|
|
|
v2.02 (991215) (Standalone version)
|
|
Problems fixed:
|
|
- Removed unnecessary output
|
|
- Fixed path for "printver.sh" in makefile
|
|
|
|
v2.01 (991122) (In-Kernel version)
|
|
New features:
|
|
- Integration in Linux kernel sources
|
|
- Support for memory mapped I/O.
|
|
|
|
v2.00 (991112)
|
|
New features:
|
|
- Full source released under GPL
|
|
|
|
v1.05 (991023)
|
|
Problems fixed:
|
|
- Compilation with kernel version 2.2.13 failed
|
|
|
|
v1.04 (990427)
|
|
Changes:
|
|
- New SMT module included, changing LED functionality
|
|
Problems fixed:
|
|
- Synchronization on SMP machines was buggy
|
|
|
|
v1.03 (990325)
|
|
Problems fixed:
|
|
- Interrupt routing on SMP machines could be incorrect
|
|
|
|
v1.02 (990310)
|
|
New features:
|
|
- Support for kernel versions 2.2.x added
|
|
- Kernel patch instead of private duplicate of kernel functions
|
|
|
|
v1.01 (980812)
|
|
Problems fixed:
|
|
Connection hangup with telnet
|
|
Slow telnet connection
|
|
|
|
v1.00 beta 01 (980507)
|
|
New features:
|
|
None.
|
|
Problems fixed:
|
|
None.
|
|
Known limitations:
|
|
- tar archive instead of standard package format (rpm).
|
|
- FDDI statistic is empty.
|
|
- not tested with 2.1.xx kernels
|
|
- integration in kernel not tested
|
|
- not tested simultaneously with FDDI adapters from other vendors.
|
|
- only X86 processors supported.
|
|
- SBA (Synchronous Bandwidth Allocator) parameters can
|
|
not be configured.
|
|
- does not work on some COMPAQ machines. See the PCI howto
|
|
document for details about this problem.
|
|
- data corruption with kernel versions below 2.0.33.
|
|
|
|
*** End of information file ***
|