117 lines
3.8 KiB
Plaintext
117 lines
3.8 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Realtek device configuration
|
|
#
|
|
|
|
config NET_VENDOR_REALTEK
|
|
bool "Realtek devices"
|
|
default y
|
|
depends on PCI || (PARPORT && X86)
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Realtek devices. If you say Y, you will be asked for
|
|
your specific card in the following questions.
|
|
|
|
if NET_VENDOR_REALTEK
|
|
|
|
config ATP
|
|
tristate "AT-LAN-TEC/RealTek pocket adapter support"
|
|
depends on PARPORT && X86
|
|
select CRC32
|
|
---help---
|
|
This is a network (Ethernet) device which attaches to your parallel
|
|
port. Read the file <file:drivers/net/ethernet/realtek/atp.c>
|
|
if you want to use this. If you intend to use this driver, you
|
|
should have said N to the "Parallel printer support", because the two
|
|
drivers don't like each other.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called atp.
|
|
|
|
config 8139CP
|
|
tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support"
|
|
depends on PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
This is a driver for the Fast Ethernet PCI network cards based on
|
|
the RTL8139C+ chips. If you have one of those, say Y here.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called 8139cp. This is recommended.
|
|
|
|
config 8139TOO
|
|
tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
|
|
depends on PCI
|
|
select CRC32
|
|
select MII
|
|
---help---
|
|
This is a driver for the Fast Ethernet PCI network cards based on
|
|
the RTL 8129/8130/8139 chips. If you have one of those, say Y here.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called 8139too. This is recommended.
|
|
|
|
config 8139TOO_PIO
|
|
bool "Use PIO instead of MMIO"
|
|
default y
|
|
depends on 8139TOO
|
|
---help---
|
|
This instructs the driver to use programmed I/O ports (PIO) instead
|
|
of PCI shared memory (MMIO). This can possibly solve some problems
|
|
in case your mainboard has memory consistency issues. If unsure,
|
|
say N.
|
|
|
|
config 8139TOO_TUNE_TWISTER
|
|
bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
|
|
depends on 8139TOO
|
|
---help---
|
|
This implements a function which might come in handy in case you
|
|
are using low quality on long cabling. It is required for RealTek
|
|
RTL-8139 revision K boards, and totally unused otherwise. It tries
|
|
to match the transceiver to the cable characteristics. This is
|
|
experimental since hardly documented by the manufacturer.
|
|
If unsure, say Y.
|
|
|
|
config 8139TOO_8129
|
|
bool "Support for older RTL-8129/8130 boards"
|
|
depends on 8139TOO
|
|
---help---
|
|
This enables support for the older and uncommon RTL-8129 and
|
|
RTL-8130 chips, which support MII via an external transceiver,
|
|
instead of an internal one. Disabling this option will save some
|
|
memory by making the code size smaller. If unsure, say Y.
|
|
|
|
config 8139_OLD_RX_RESET
|
|
bool "Use older RX-reset method"
|
|
depends on 8139TOO
|
|
---help---
|
|
The 8139too driver was recently updated to contain a more rapid
|
|
reset sequence, in the face of severe receive errors. This "new"
|
|
RX-reset method should be adequate for all boards. But if you
|
|
experience problems, you can enable this option to restore the
|
|
old RX-reset behavior. If unsure, say N.
|
|
|
|
config R8169
|
|
tristate "Realtek 8169/8168/8101/8125 ethernet support"
|
|
depends on PCI
|
|
select FW_LOADER
|
|
select CRC32
|
|
select PHYLIB
|
|
select REALTEK_PHY
|
|
---help---
|
|
Say Y here if you have a Realtek Ethernet adapter belonging to
|
|
the following families:
|
|
RTL8169 Gigabit Ethernet
|
|
RTL8168 Gigabit Ethernet
|
|
RTL8101 Fast Ethernet
|
|
RTL8125 2.5GBit Ethernet
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called r8169. This is recommended.
|
|
|
|
endif # NET_VENDOR_REALTEK
|