368 lines
6.8 KiB
Plaintext
368 lines
6.8 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
|
|
/*
|
|
* Copyright (C) 2018 Zodiac Inflight Innovations
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "vf610.dtsi"
|
|
|
|
/ {
|
|
model = "ZII VF610 CFU1 Board";
|
|
compatible = "zii,vf610cfu1", "zii,vf610dev", "fsl,vf610";
|
|
|
|
chosen {
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
memory@80000000 {
|
|
device_type = "memory";
|
|
reg = <0x80000000 0x20000000>;
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&pinctrl_leds_debug>;
|
|
pinctrl-names = "default";
|
|
|
|
led-debug {
|
|
label = "zii:green:debug1";
|
|
gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
led-fail {
|
|
label = "zii:red:fail";
|
|
gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
led-status {
|
|
label = "zii:green:status";
|
|
gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
led-debug-a {
|
|
label = "zii:green:debug_a";
|
|
gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
led-debug-b {
|
|
label = "zii:green:debug_b";
|
|
gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
|
|
reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc_3v3_mcu";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
sff: sfp {
|
|
compatible = "sff,sff";
|
|
pinctrl-0 = <&pinctrl_optical>;
|
|
pinctrl-names = "default";
|
|
i2c-bus = <&i2c0>;
|
|
los-gpio = <&gpio4 4 GPIO_ACTIVE_HIGH>;
|
|
tx-disable-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
supply-voltage-monitor {
|
|
compatible = "iio-hwmon";
|
|
io-channels = <&adc0 8>, /* 28VDC_IN */
|
|
<&adc0 9>, /* +3.3V */
|
|
<&adc1 8>, /* VCC_1V5 */
|
|
<&adc1 9>; /* VCC_1V2 */
|
|
};
|
|
};
|
|
|
|
&adc0 {
|
|
vref-supply = <®_vcc_3v3_mcu>;
|
|
status = "okay";
|
|
};
|
|
|
|
&adc1 {
|
|
vref-supply = <®_vcc_3v3_mcu>;
|
|
status = "okay";
|
|
};
|
|
|
|
&dspi1 {
|
|
bus-num = <1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_dspi1>;
|
|
/*
|
|
* Some CFU1s come with SPI-NOR chip DNPed, so we leave this
|
|
* node disabled by default and rely on bootloader to enable
|
|
* it when appropriate.
|
|
*/
|
|
status = "disabled";
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "m25p128", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partition@0 {
|
|
label = "m25p128-0";
|
|
reg = <0x0 0x01000000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&edma0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&edma1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&esdhc0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_esdhc0>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
no-1-8-v;
|
|
keep-power-in-suspend;
|
|
no-sdio;
|
|
no-sd;
|
|
status = "okay";
|
|
};
|
|
|
|
&esdhc1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_esdhc1>;
|
|
bus-width = <4>;
|
|
no-sdio;
|
|
status = "okay";
|
|
};
|
|
|
|
&fec1 {
|
|
phy-mode = "rmii";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_fec1>;
|
|
status = "okay";
|
|
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
|
|
mdio1: mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
switch0: switch0@0 {
|
|
compatible = "marvell,mv88e6085";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_switch>;
|
|
reg = <0>;
|
|
eeprom-length = <512>;
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "eth_cu_1000_1";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "eth_cu_1000_2";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "eth_cu_1000_3";
|
|
};
|
|
|
|
port@5 {
|
|
reg = <5>;
|
|
label = "eth_fc_1000_1";
|
|
phy-mode = "1000base-x";
|
|
managed = "in-band-status";
|
|
sfp = <&sff>;
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
label = "cpu";
|
|
ethernet = <&fec1>;
|
|
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c0 {
|
|
clock-frequency = <100000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c0>;
|
|
status = "okay";
|
|
|
|
io-expander@22 {
|
|
compatible = "nxp,pca9554";
|
|
reg = <0x22>;
|
|
gpio-controller;
|
|
};
|
|
|
|
lm75@48 {
|
|
compatible = "national,lm75";
|
|
reg = <0x48>;
|
|
};
|
|
|
|
eeprom@52 {
|
|
compatible = "atmel,24c04";
|
|
reg = <0x52>;
|
|
label = "nvm";
|
|
};
|
|
|
|
eeprom@54 {
|
|
compatible = "atmel,24c04";
|
|
reg = <0x54>;
|
|
label = "nameplate";
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <100000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c1>;
|
|
status = "okay";
|
|
|
|
watchdog@38 {
|
|
compatible = "zii,rave-wdt";
|
|
reg = <0x38>;
|
|
};
|
|
};
|
|
|
|
&snvsrtc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&iomuxc {
|
|
pinctrl_dspi1: dspi1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTD5__DSPI1_CS0 0x1182
|
|
VF610_PAD_PTC6__DSPI1_SIN 0x1181
|
|
VF610_PAD_PTC7__DSPI1_SOUT 0x1182
|
|
VF610_PAD_PTC8__DSPI1_SCK 0x1182
|
|
>;
|
|
};
|
|
|
|
pinctrl_esdhc0: esdhc0grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
|
|
VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
|
|
VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
|
|
VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
|
|
VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
|
|
VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
|
|
VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
|
|
VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
|
|
VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
|
|
VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
|
|
>;
|
|
};
|
|
|
|
pinctrl_esdhc1: esdhc1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
|
|
VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
|
|
VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
|
|
VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
|
|
VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
|
|
VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
|
|
>;
|
|
};
|
|
|
|
pinctrl_fec1: fec1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTA6__RMII_CLKIN 0x30d1
|
|
VF610_PAD_PTC9__ENET_RMII1_MDC 0x30fe
|
|
VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
|
|
VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
|
|
VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
|
|
VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
|
|
VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
|
|
VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
|
|
VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
|
|
VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c0: i2c0grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB14__I2C0_SCL 0x37ff
|
|
VF610_PAD_PTB15__I2C0_SDA 0x37ff
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c1: i2c1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB16__I2C1_SCL 0x37ff
|
|
VF610_PAD_PTB17__I2C1_SDA 0x37ff
|
|
>;
|
|
};
|
|
|
|
pinctrl_leds_debug: pinctrl-leds-debug {
|
|
fsl,pins = <
|
|
VF610_PAD_PTD3__GPIO_82 0x31c2
|
|
VF610_PAD_PTE3__GPIO_108 0x31c2
|
|
VF610_PAD_PTE4__GPIO_109 0x31c2
|
|
VF610_PAD_PTE5__GPIO_110 0x31c2
|
|
VF610_PAD_PTE6__GPIO_111 0x31c2
|
|
>;
|
|
};
|
|
|
|
pinctrl_optical: optical-grp {
|
|
fsl,pins = <
|
|
/* SFF SD input */
|
|
VF610_PAD_PTE27__GPIO_132 0x3061
|
|
|
|
/* SFF Transmit disable output */
|
|
VF610_PAD_PTE13__GPIO_118 0x3043
|
|
>;
|
|
};
|
|
|
|
pinctrl_switch: switch-grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB28__GPIO_98 0x3061
|
|
VF610_PAD_PTE2__GPIO_107 0x1042
|
|
>;
|
|
};
|
|
|
|
pinctrl_uart0: uart0grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB10__UART0_TX 0x21a2
|
|
VF610_PAD_PTB11__UART0_RX 0x21a1
|
|
>;
|
|
};
|
|
};
|