UbiquitousOS
/
OpenCloudOS-Kernel
mirror of https://gitee.com/OpenCloudOS/OpenCloudOS-Kernel.git
11
0
Fork 0
Code Issues Projects Releases Wiki Activity
OpenCloudOS-Kernel/drivers/i2c/busses/i2c-cadence.c

1025 lines
29 KiB
C
Raw Blame History

/*
* I2C bus driver for the Cadence I2C controller.
*
* Copyright (C) 2009 - 2014 Xilinx, Inc.
*
* This program is free software; you can redistribute it
* and/or modify it under the terms of the GNU General Public
* License as published by the Free Software Foundation;
* either version 2 of the License, or (at your option) any
* later version.
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/of.h>
#include <linux/pm_runtime.h>
/* Register offsets for the I2C device. */
#define CDNS_I2C_CR_OFFSET 0x00 /* Control Register, RW */
#define CDNS_I2C_SR_OFFSET 0x04 /* Status Register, RO */
#define CDNS_I2C_ADDR_OFFSET 0x08 /* I2C Address Register, RW */
#define CDNS_I2C_DATA_OFFSET 0x0C /* I2C Data Register, RW */
#define CDNS_I2C_ISR_OFFSET 0x10 /* IRQ Status Register, RW */
#define CDNS_I2C_XFER_SIZE_OFFSET 0x14 /* Transfer Size Register, RW */
#define CDNS_I2C_TIME_OUT_OFFSET 0x1C /* Time Out Register, RW */
#define CDNS_I2C_IER_OFFSET 0x24 /* IRQ Enable Register, WO */
#define CDNS_I2C_IDR_OFFSET 0x28 /* IRQ Disable Register, WO */
/* Control Register Bit mask definitions */
#define CDNS_I2C_CR_HOLD BIT(4) /* Hold Bus bit */
#define CDNS_I2C_CR_ACK_EN BIT(3)
#define CDNS_I2C_CR_NEA BIT(2)
#define CDNS_I2C_CR_MS BIT(1)
/* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */
#define CDNS_I2C_CR_RW BIT(0)
/* 1 = Auto init FIFO to zeroes */
#define CDNS_I2C_CR_CLR_FIFO BIT(6)
#define CDNS_I2C_CR_DIVA_SHIFT 14
#define CDNS_I2C_CR_DIVA_MASK (3 << CDNS_I2C_CR_DIVA_SHIFT)
#define CDNS_I2C_CR_DIVB_SHIFT 8
#define CDNS_I2C_CR_DIVB_MASK (0x3f << CDNS_I2C_CR_DIVB_SHIFT)
/* Status Register Bit mask definitions */
#define CDNS_I2C_SR_BA BIT(8)
#define CDNS_I2C_SR_RXDV BIT(5)
/*
* I2C Address Register Bit mask definitions
* Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0]
* bits. A write access to this register always initiates a transfer if the I2C
* is in master mode.
*/
#define CDNS_I2C_ADDR_MASK 0x000003FF /* I2C Address Mask */
/*
* I2C Interrupt Registers Bit mask definitions
* All the four interrupt registers (Status/Mask/Enable/Disable) have the same
* bit definitions.
*/
#define CDNS_I2C_IXR_ARB_LOST BIT(9)
#define CDNS_I2C_IXR_RX_UNF BIT(7)
#define CDNS_I2C_IXR_TX_OVF BIT(6)
#define CDNS_I2C_IXR_RX_OVF BIT(5)
#define CDNS_I2C_IXR_SLV_RDY BIT(4)
#define CDNS_I2C_IXR_TO BIT(3)
#define CDNS_I2C_IXR_NACK BIT(2)
#define CDNS_I2C_IXR_DATA BIT(1)
#define CDNS_I2C_IXR_COMP BIT(0)
#define CDNS_I2C_IXR_ALL_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \
CDNS_I2C_IXR_RX_UNF | \
CDNS_I2C_IXR_TX_OVF | \
CDNS_I2C_IXR_RX_OVF | \
CDNS_I2C_IXR_SLV_RDY | \
CDNS_I2C_IXR_TO | \
CDNS_I2C_IXR_NACK | \
CDNS_I2C_IXR_DATA | \
CDNS_I2C_IXR_COMP)
#define CDNS_I2C_IXR_ERR_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \
CDNS_I2C_IXR_RX_UNF | \
CDNS_I2C_IXR_TX_OVF | \
CDNS_I2C_IXR_RX_OVF | \
CDNS_I2C_IXR_NACK)
#define CDNS_I2C_ENABLED_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \
CDNS_I2C_IXR_RX_UNF | \
CDNS_I2C_IXR_TX_OVF | \
CDNS_I2C_IXR_RX_OVF | \
CDNS_I2C_IXR_NACK | \
CDNS_I2C_IXR_DATA | \
CDNS_I2C_IXR_COMP)
#define CDNS_I2C_TIMEOUT msecs_to_jiffies(1000)
/* timeout for pm runtime autosuspend */
#define CNDS_I2C_PM_TIMEOUT 1000 /* ms */
#define CDNS_I2C_FIFO_DEPTH 16
/* FIFO depth at which the DATA interrupt occurs */
#define CDNS_I2C_DATA_INTR_DEPTH (CDNS_I2C_FIFO_DEPTH - 2)
#define CDNS_I2C_MAX_TRANSFER_SIZE 255
/* Transfer size in multiples of data interrupt depth */
#define CDNS_I2C_TRANSFER_SIZE (CDNS_I2C_MAX_TRANSFER_SIZE - 3)
#define DRIVER_NAME "cdns-i2c"
#define CDNS_I2C_SPEED_MAX 400000
#define CDNS_I2C_SPEED_DEFAULT 100000
#define CDNS_I2C_DIVA_MAX 4
#define CDNS_I2C_DIVB_MAX 64
#define CDNS_I2C_TIMEOUT_MAX 0xFF
#define CDNS_I2C_BROKEN_HOLD_BIT BIT(0)
#define cdns_i2c_readreg(offset) readl_relaxed(id->membase + offset)
#define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset)
/**
* struct cdns_i2c - I2C device private data structure
*
* @dev: Pointer to device structure
* @membase: Base address of the I2C device
* @adap: I2C adapter instance
* @p_msg: Message pointer
* @err_status: Error status in Interrupt Status Register
* @xfer_done: Transfer complete status
* @p_send_buf: Pointer to transmit buffer
* @p_recv_buf: Pointer to receive buffer
* @send_count: Number of bytes still expected to send
* @recv_count: Number of bytes still expected to receive
* @curr_recv_count: Number of bytes to be received in current transfer
* @irq: IRQ number
* @input_clk: Input clock to I2C controller
* @i2c_clk: Maximum I2C clock speed
* @bus_hold_flag: Flag used in repeated start for clearing HOLD bit
* @clk: Pointer to struct clk
* @clk_rate_change_nb: Notifier block for clock rate changes
* @quirks: flag for broken hold bit usage in r1p10
*/
struct cdns_i2c {
struct device *dev;
void __iomem *membase;
struct i2c_adapter adap;
struct i2c_msg *p_msg;
int err_status;
struct completion xfer_done;
unsigned char *p_send_buf;
unsigned char *p_recv_buf;
unsigned int send_count;
unsigned int recv_count;
unsigned int curr_recv_count;
int irq;
unsigned long input_clk;
unsigned int i2c_clk;
unsigned int bus_hold_flag;
struct clk *clk;
struct notifier_block clk_rate_change_nb;
u32 quirks;
};
struct cdns_platform_data {
u32 quirks;
};
#define to_cdns_i2c(_nb) container_of(_nb, struct cdns_i2c, \
clk_rate_change_nb)
/**
* cdns_i2c_clear_bus_hold - Clear bus hold bit
* @id: Pointer to driver data struct
*
* Helper to clear the controller's bus hold bit.
*/
static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id)
{
u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
if (reg & CDNS_I2C_CR_HOLD)
cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET);
}
static inline bool cdns_is_holdquirk(struct cdns_i2c *id, bool hold_wrkaround)
{
return (hold_wrkaround &&
(id->curr_recv_count == CDNS_I2C_FIFO_DEPTH + 1));
}
/**
* cdns_i2c_isr - Interrupt handler for the I2C device
* @irq: irq number for the I2C device
* @ptr: void pointer to cdns_i2c structure
*
* This function handles the data interrupt, transfer complete interrupt and
* the error interrupts of the I2C device.
*
* Return: IRQ_HANDLED always
*/
static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
{
unsigned int isr_status, avail_bytes, updatetx;
unsigned int bytes_to_send;
bool hold_quirk;
struct cdns_i2c *id = ptr;
/* Signal completion only after everything is updated */
int done_flag = 0;
irqreturn_t status = IRQ_NONE;
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
/* Handling nack and arbitration lost interrupt */
if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) {
done_flag = 1;
status = IRQ_HANDLED;
}
/*
* Check if transfer size register needs to be updated again for a
* large data receive operation.
*/
updatetx = 0;
if (id->recv_count > id->curr_recv_count)
updatetx = 1;
hold_quirk = (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT) && updatetx;
/* When receiving, handle data interrupt and completion interrupt */
if (id->p_recv_buf &&
((isr_status & CDNS_I2C_IXR_COMP) ||
(isr_status & CDNS_I2C_IXR_DATA))) {
/* Read data if receive data valid is set */
while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) &
CDNS_I2C_SR_RXDV) {
/*
* Clear hold bit that was set for FIFO control if
* RX data left is less than FIFO depth, unless
* repeated start is selected.
*/
if ((id->recv_count < CDNS_I2C_FIFO_DEPTH) &&
!id->bus_hold_flag)
cdns_i2c_clear_bus_hold(id);
*(id->p_recv_buf)++ =
cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
id->recv_count--;
id->curr_recv_count--;
if (cdns_is_holdquirk(id, hold_quirk))
break;
}
/*
* The controller sends NACK to the slave when transfer size
* register reaches zero without considering the HOLD bit.
* This workaround is implemented for large data transfers to
* maintain transfer size non-zero while performing a large
* receive operation.
*/
if (cdns_is_holdquirk(id, hold_quirk)) {
/* wait while fifo is full */
while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) !=
(id->curr_recv_count - CDNS_I2C_FIFO_DEPTH))
;
/*
* Check number of bytes to be received against maximum
* transfer size and update register accordingly.
*/
if (((int)(id->recv_count) - CDNS_I2C_FIFO_DEPTH) >
CDNS_I2C_TRANSFER_SIZE) {
cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
CDNS_I2C_XFER_SIZE_OFFSET);
id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE +
CDNS_I2C_FIFO_DEPTH;
} else {
cdns_i2c_writereg(id->recv_count -
CDNS_I2C_FIFO_DEPTH,
CDNS_I2C_XFER_SIZE_OFFSET);
id->curr_recv_count = id->recv_count;
}
} else if (id->recv_count && !hold_quirk &&
!id->curr_recv_count) {
/* Set the slave address in address register*/
cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
CDNS_I2C_ADDR_OFFSET);
if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
CDNS_I2C_XFER_SIZE_OFFSET);
id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
} else {
cdns_i2c_writereg(id->recv_count,
CDNS_I2C_XFER_SIZE_OFFSET);
id->curr_recv_count = id->recv_count;
}
}
/* Clear hold (if not repeated start) and signal completion */
if ((isr_status & CDNS_I2C_IXR_COMP) && !id->recv_count) {
if (!id->bus_hold_flag)
cdns_i2c_clear_bus_hold(id);
done_flag = 1;
}
status = IRQ_HANDLED;
}
/* When sending, handle transfer complete interrupt */
if ((isr_status & CDNS_I2C_IXR_COMP) && !id->p_recv_buf) {
/*
* If there is more data to be sent, calculate the
* space available in FIFO and fill with that many bytes.
*/
if (id->send_count) {
avail_bytes = CDNS_I2C_FIFO_DEPTH -
cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
if (id->send_count > avail_bytes)
bytes_to_send = avail_bytes;
else
bytes_to_send = id->send_count;
while (bytes_to_send--) {
cdns_i2c_writereg(
(*(id->p_send_buf)++),
CDNS_I2C_DATA_OFFSET);
id->send_count--;
}
} else {
/*
* Signal the completion of transaction and
* clear the hold bus bit if there are no
* further messages to be processed.
*/
done_flag = 1;
}
if (!id->send_count && !id->bus_hold_flag)
cdns_i2c_clear_bus_hold(id);
status = IRQ_HANDLED;
}
/* Update the status for errors */
id->err_status = isr_status & CDNS_I2C_IXR_ERR_INTR_MASK;
if (id->err_status)
status = IRQ_HANDLED;
if (done_flag)
complete(&id->xfer_done);
return status;
}
/**
* cdns_i2c_mrecv - Prepare and start a master receive operation
* @id: pointer to the i2c device structure
*/
static void cdns_i2c_mrecv(struct cdns_i2c *id)
{
unsigned int ctrl_reg;
unsigned int isr_status;
id->p_recv_buf = id->p_msg->buf;
id->recv_count = id->p_msg->len;
/* Put the controller in master receive mode and clear the FIFO */
ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO;
if (id->p_msg->flags & I2C_M_RECV_LEN)
id->recv_count = I2C_SMBUS_BLOCK_MAX + 1;
id->curr_recv_count = id->recv_count;
/*
* Check for the message size against FIFO depth and set the
* 'hold bus' bit if it is greater than FIFO depth.
*/
if (id->recv_count > CDNS_I2C_FIFO_DEPTH)
ctrl_reg |= CDNS_I2C_CR_HOLD;
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
/* Clear the interrupts in interrupt status register */
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
/*
* The no. of bytes to receive is checked against the limit of
* max transfer size. Set transfer size register with no of bytes
* receive if it is less than transfer size and transfer size if
* it is more. Enable the interrupts.
*/
if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
CDNS_I2C_XFER_SIZE_OFFSET);
id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
} else {
cdns_i2c_writereg(id->recv_count, CDNS_I2C_XFER_SIZE_OFFSET);
}
/* Clear the bus hold flag if bytes to receive is less than FIFO size */
if (!id->bus_hold_flag &&
((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
(id->recv_count <= CDNS_I2C_FIFO_DEPTH))
cdns_i2c_clear_bus_hold(id);
/* Set the slave address in address register - triggers operation */
cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
CDNS_I2C_ADDR_OFFSET);
cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
}
/**
* cdns_i2c_msend - Prepare and start a master send operation
* @id: pointer to the i2c device
*/
static void cdns_i2c_msend(struct cdns_i2c *id)
{
unsigned int avail_bytes;
unsigned int bytes_to_send;
unsigned int ctrl_reg;
unsigned int isr_status;
id->p_recv_buf = NULL;
id->p_send_buf = id->p_msg->buf;
id->send_count = id->p_msg->len;
/* Set the controller in Master transmit mode and clear the FIFO. */
ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
ctrl_reg &= ~CDNS_I2C_CR_RW;
ctrl_reg |= CDNS_I2C_CR_CLR_FIFO;
/*
* Check for the message size against FIFO depth and set the
* 'hold bus' bit if it is greater than FIFO depth.
*/
if (id->send_count > CDNS_I2C_FIFO_DEPTH)
ctrl_reg |= CDNS_I2C_CR_HOLD;
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
/* Clear the interrupts in interrupt status register. */
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
/*
* Calculate the space available in FIFO. Check the message length
* against the space available, and fill the FIFO accordingly.
* Enable the interrupts.
*/
avail_bytes = CDNS_I2C_FIFO_DEPTH -
cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
if (id->send_count > avail_bytes)
bytes_to_send = avail_bytes;
else
bytes_to_send = id->send_count;
while (bytes_to_send--) {
cdns_i2c_writereg((*(id->p_send_buf)++), CDNS_I2C_DATA_OFFSET);
id->send_count--;
}
/*
* Clear the bus hold flag if there is no more data
* and if it is the last message.
*/
if (!id->bus_hold_flag && !id->send_count)
cdns_i2c_clear_bus_hold(id);
/* Set the slave address in address register - triggers operation. */
cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
CDNS_I2C_ADDR_OFFSET);
cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
}
/**
* cdns_i2c_master_reset - Reset the interface
* @adap: pointer to the i2c adapter driver instance
*
* This function cleanup the fifos, clear the hold bit and status
* and disable the interrupts.
*/
static void cdns_i2c_master_reset(struct i2c_adapter *adap)
{
struct cdns_i2c *id = adap->algo_data;
u32 regval;
/* Disable the interrupts */
cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
/* Clear the hold bit and fifos */
regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
regval &= ~CDNS_I2C_CR_HOLD;
regval |= CDNS_I2C_CR_CLR_FIFO;
cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET);
/* Update the transfercount register to zero */
cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET);
/* Clear the interupt status register */
regval = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
cdns_i2c_writereg(regval, CDNS_I2C_ISR_OFFSET);
/* Clear the status register */
regval = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
cdns_i2c_writereg(regval, CDNS_I2C_SR_OFFSET);
}
static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg,
struct i2c_adapter *adap)
{
unsigned long time_left;
u32 reg;
id->p_msg = msg;
id->err_status = 0;
reinit_completion(&id->xfer_done);
/* Check for the TEN Bit mode on each msg */
reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
if (msg->flags & I2C_M_TEN) {
if (reg & CDNS_I2C_CR_NEA)
cdns_i2c_writereg(reg & ~CDNS_I2C_CR_NEA,
CDNS_I2C_CR_OFFSET);
} else {
if (!(reg & CDNS_I2C_CR_NEA))
cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA,
CDNS_I2C_CR_OFFSET);
}
/* Check for the R/W flag on each msg */
if (msg->flags & I2C_M_RD)
cdns_i2c_mrecv(id);
else
cdns_i2c_msend(id);
/* Wait for the signal of completion */
time_left = wait_for_completion_timeout(&id->xfer_done, adap->timeout);
if (time_left == 0) {
cdns_i2c_master_reset(adap);
dev_err(id->adap.dev.parent,
"timeout waiting on completion\n");
return -ETIMEDOUT;
}
cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK,
CDNS_I2C_IDR_OFFSET);
/* If it is bus arbitration error, try again */
if (id->err_status & CDNS_I2C_IXR_ARB_LOST)
return -EAGAIN;
return 0;
}
/**
* cdns_i2c_master_xfer - The main i2c transfer function
* @adap: pointer to the i2c adapter driver instance
* @msgs: pointer to the i2c message structure
* @num: the number of messages to transfer
*
* Initiates the send/recv activity based on the transfer message received.
*
* Return: number of msgs processed on success, negative error otherwise
*/
static int cdns_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
int num)
{
int ret, count;
u32 reg;
struct cdns_i2c *id = adap->algo_data;
bool hold_quirk;
ret = pm_runtime_get_sync(id->dev);
if (ret < 0)
return ret;
/* Check if the bus is free */
if (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & CDNS_I2C_SR_BA) {
ret = -EAGAIN;
goto out;
}
hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT);
/*
* Set the flag to one when multiple messages are to be
* processed with a repeated start.
*/
if (num > 1) {
/*
* This controller does not give completion interrupt after a
* master receive message if HOLD bit is set (repeated start),
* resulting in SW timeout. Hence, if a receive message is
* followed by any other message, an error is returned
* indicating that this sequence is not supported.
*/
for (count = 0; (count < num - 1 && hold_quirk); count++) {
if (msgs[count].flags & I2C_M_RD) {
dev_warn(adap->dev.parent,
"Can't do repeated start after a receive message\n");
ret = -EOPNOTSUPP;
goto out;
}
}
id->bus_hold_flag = 1;
reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
reg |= CDNS_I2C_CR_HOLD;
cdns_i2c_writereg(reg, CDNS_I2C_CR_OFFSET);
} else {
id->bus_hold_flag = 0;
}
/* Process the msg one by one */
for (count = 0; count < num; count++, msgs++) {
if (count == (num - 1))
id->bus_hold_flag = 0;
ret = cdns_i2c_process_msg(id, msgs, adap);
if (ret)
goto out;
/* Report the other error interrupts to application */
if (id->err_status) {
cdns_i2c_master_reset(adap);
if (id->err_status & CDNS_I2C_IXR_NACK) {
ret = -ENXIO;
goto out;
}
ret = -EIO;
goto out;
}
}
ret = num;
out:
pm_runtime_mark_last_busy(id->dev);
pm_runtime_put_autosuspend(id->dev);
return ret;
}
/**
* cdns_i2c_func - Returns the supported features of the I2C driver
* @adap: pointer to the i2c adapter structure
*
* Return: 32 bit value, each bit corresponding to a feature
*/
static u32 cdns_i2c_func(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR |
(I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) |
I2C_FUNC_SMBUS_BLOCK_DATA;
}
static const struct i2c_algorithm cdns_i2c_algo = {
.master_xfer = cdns_i2c_master_xfer,
.functionality = cdns_i2c_func,
};
/**
* cdns_i2c_calc_divs - Calculate clock dividers
* @f: I2C clock frequency
* @input_clk: Input clock frequency
* @a: First divider (return value)
* @b: Second divider (return value)
*
* f is used as input and output variable. As input it is used as target I2C
* frequency. On function exit f holds the actually resulting I2C frequency.
*
* Return: 0 on success, negative errno otherwise.
*/
static int cdns_i2c_calc_divs(unsigned long *f, unsigned long input_clk,
unsigned int *a, unsigned int *b)
{
unsigned long fscl = *f, best_fscl = *f, actual_fscl, temp;
unsigned int div_a, div_b, calc_div_a = 0, calc_div_b = 0;
unsigned int last_error, current_error;
/* calculate (divisor_a+1) x (divisor_b+1) */
temp = input_clk / (22 * fscl);
/*
* If the calculated value is negative or 0, the fscl input is out of
* range. Return error.
*/
if (!temp || (temp > (CDNS_I2C_DIVA_MAX * CDNS_I2C_DIVB_MAX)))
return -EINVAL;
last_error = -1;
for (div_a = 0; div_a < CDNS_I2C_DIVA_MAX; div_a++) {
div_b = DIV_ROUND_UP(input_clk, 22 * fscl * (div_a + 1));
if ((div_b < 1) || (div_b > CDNS_I2C_DIVB_MAX))
continue;
div_b--;
actual_fscl = input_clk / (22 * (div_a + 1) * (div_b + 1));
if (actual_fscl > fscl)
continue;
current_error = ((actual_fscl > fscl) ? (actual_fscl - fscl) :
(fscl - actual_fscl));
if (last_error > current_error) {
calc_div_a = div_a;
calc_div_b = div_b;
best_fscl = actual_fscl;
last_error = current_error;
}
}
*a = calc_div_a;
*b = calc_div_b;
*f = best_fscl;
return 0;
}
/**
* cdns_i2c_setclk - This function sets the serial clock rate for the I2C device
* @clk_in: I2C clock input frequency in Hz
* @id: Pointer to the I2C device structure
*
* The device must be idle rather than busy transferring data before setting
* these device options.
* The data rate is set by values in the control register.
* The formula for determining the correct register values is
* Fscl = Fpclk/(22 x (divisor_a+1) x (divisor_b+1))
* See the hardware data sheet for a full explanation of setting the serial
* clock rate. The clock can not be faster than the input clock divide by 22.
* The two most common clock rates are 100KHz and 400KHz.
*
* Return: 0 on success, negative error otherwise
*/
static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id)
{
unsigned int div_a, div_b;
unsigned int ctrl_reg;
int ret = 0;
unsigned long fscl = id->i2c_clk;
ret = cdns_i2c_calc_divs(&fscl, clk_in, &div_a, &div_b);
if (ret)
return ret;
ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
ctrl_reg &= ~(CDNS_I2C_CR_DIVA_MASK | CDNS_I2C_CR_DIVB_MASK);
ctrl_reg |= ((div_a << CDNS_I2C_CR_DIVA_SHIFT) |
(div_b << CDNS_I2C_CR_DIVB_SHIFT));
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
return 0;
}
/**
* cdns_i2c_clk_notifier_cb - Clock rate change callback
* @nb: Pointer to notifier block
* @event: Notification reason
* @data: Pointer to notification data object
*
* This function is called when the cdns_i2c input clock frequency changes.
* The callback checks whether a valid bus frequency can be generated after the
* change. If so, the change is acknowledged, otherwise the change is aborted.
* New dividers are written to the HW in the pre- or post change notification
* depending on the scaling direction.
*
* Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
* to acknowledge the change, NOTIFY_DONE if the notification is
* considered irrelevant.
*/
static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
event, void *data)
{
struct clk_notifier_data *ndata = data;
struct cdns_i2c *id = to_cdns_i2c(nb);
if (pm_runtime_suspended(id->dev))
return NOTIFY_OK;
switch (event) {
case PRE_RATE_CHANGE:
{
unsigned long input_clk = ndata->new_rate;
unsigned long fscl = id->i2c_clk;
unsigned int div_a, div_b;
int ret;
ret = cdns_i2c_calc_divs(&fscl, input_clk, &div_a, &div_b);
if (ret) {
dev_warn(id->adap.dev.parent,
"clock rate change rejected\n");
return NOTIFY_STOP;
}
/* scale up */
if (ndata->new_rate > ndata->old_rate)
cdns_i2c_setclk(ndata->new_rate, id);
return NOTIFY_OK;
}
case POST_RATE_CHANGE:
id->input_clk = ndata->new_rate;
/* scale down */
if (ndata->new_rate < ndata->old_rate)
cdns_i2c_setclk(ndata->new_rate, id);
return NOTIFY_OK;
case ABORT_RATE_CHANGE:
/* scale up */
if (ndata->new_rate > ndata->old_rate)
cdns_i2c_setclk(ndata->old_rate, id);
return NOTIFY_OK;
default:
return NOTIFY_DONE;
}
}
/**
* cdns_i2c_runtime_suspend - Runtime suspend method for the driver
* @dev: Address of the platform_device structure
*
* Put the driver into low power mode.
*
* Return: 0 always
*/
static int __maybe_unused cdns_i2c_runtime_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct cdns_i2c *xi2c = platform_get_drvdata(pdev);
clk_disable(xi2c->clk);
return 0;
}
/**
* cdns_i2c_runtime_resume - Runtime resume
* @dev: Address of the platform_device structure
*
* Runtime resume callback.
*
* Return: 0 on success and error value on error
*/
static int __maybe_unused cdns_i2c_runtime_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct cdns_i2c *xi2c = platform_get_drvdata(pdev);
int ret;
ret = clk_enable(xi2c->clk);
if (ret) {
dev_err(dev, "Cannot enable clock.\n");
return ret;
}
return 0;
}
static const struct dev_pm_ops cdns_i2c_dev_pm_ops = {
SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend,
cdns_i2c_runtime_resume, NULL)
};
static const struct cdns_platform_data r1p10_i2c_def = {
.quirks = CDNS_I2C_BROKEN_HOLD_BIT,
};
static const struct of_device_id cdns_i2c_of_match[] = {
{ .compatible = "cdns,i2c-r1p10", .data = &r1p10_i2c_def },
{ .compatible = "cdns,i2c-r1p14",},
{ /* end of table */ }
};
MODULE_DEVICE_TABLE(of, cdns_i2c_of_match);
/**
* cdns_i2c_probe - Platform registration call
* @pdev: Handle to the platform device structure
*
* This function does all the memory allocation and registration for the i2c
* device. User can modify the address mode to 10 bit address mode using the
* ioctl call with option I2C_TENBIT.
*
* Return: 0 on success, negative error otherwise
*/
static int cdns_i2c_probe(struct platform_device *pdev)
{
struct resource *r_mem;
struct cdns_i2c *id;
int ret;
const struct of_device_id *match;
id = devm_kzalloc(&pdev->dev, sizeof(*id), GFP_KERNEL);
if (!id)
return -ENOMEM;
id->dev = &pdev->dev;
platform_set_drvdata(pdev, id);
match = of_match_node(cdns_i2c_of_match, pdev->dev.of_node);
if (match && match->data) {
const struct cdns_platform_data *data = match->data;
id->quirks = data->quirks;
}
r_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
id->membase = devm_ioremap_resource(&pdev->dev, r_mem);
if (IS_ERR(id->membase))
return PTR_ERR(id->membase);
id->irq = platform_get_irq(pdev, 0);
id->adap.owner = THIS_MODULE;
id->adap.dev.of_node = pdev->dev.of_node;
id->adap.algo = &cdns_i2c_algo;
id->adap.timeout = CDNS_I2C_TIMEOUT;
id->adap.retries = 3; /* Default retry value. */
id->adap.algo_data = id;
id->adap.dev.parent = &pdev->dev;
init_completion(&id->xfer_done);
snprintf(id->adap.name, sizeof(id->adap.name),
"Cadence I2C at %08lx", (unsigned long)r_mem->start);
id->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(id->clk)) {
dev_err(&pdev->dev, "input clock not found.\n");
return PTR_ERR(id->clk);
}
ret = clk_prepare_enable(id->clk);
if (ret)
dev_err(&pdev->dev, "Unable to enable clock.\n");
pm_runtime_enable(id->dev);
pm_runtime_set_autosuspend_delay(id->dev, CNDS_I2C_PM_TIMEOUT);
pm_runtime_use_autosuspend(id->dev);
pm_runtime_set_active(id->dev);
id->clk_rate_change_nb.notifier_call = cdns_i2c_clk_notifier_cb;
if (clk_notifier_register(id->clk, &id->clk_rate_change_nb))
dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
id->input_clk = clk_get_rate(id->clk);
ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
&id->i2c_clk);
if (ret || (id->i2c_clk > CDNS_I2C_SPEED_MAX))
id->i2c_clk = CDNS_I2C_SPEED_DEFAULT;
cdns_i2c_writereg(CDNS_I2C_CR_ACK_EN | CDNS_I2C_CR_NEA | CDNS_I2C_CR_MS,
CDNS_I2C_CR_OFFSET);
ret = cdns_i2c_setclk(id->input_clk, id);
if (ret) {
dev_err(&pdev->dev, "invalid SCL clock: %u Hz\n", id->i2c_clk);
ret = -EINVAL;
goto err_clk_dis;
}
ret = devm_request_irq(&pdev->dev, id->irq, cdns_i2c_isr, 0,
DRIVER_NAME, id);
if (ret) {
dev_err(&pdev->dev, "cannot get irq %d\n", id->irq);
goto err_clk_dis;
}
/*
* Cadence I2C controller has a bug wherein it generates
* invalid read transaction after HW timeout in master receiver mode.
* HW timeout is not used by this driver and the interrupt is disabled.
* But the feature itself cannot be disabled. Hence maximum value
* is written to this register to reduce the chances of error.
*/
cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET);
ret = i2c_add_adapter(&id->adap);
if (ret < 0)
goto err_clk_dis;
dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n",
id->i2c_clk / 1000, (unsigned long)r_mem->start, id->irq);
return 0;
err_clk_dis:
clk_disable_unprepare(id->clk);
pm_runtime_set_suspended(&pdev->dev);
pm_runtime_disable(&pdev->dev);
return ret;
}
/**
* cdns_i2c_remove - Unregister the device after releasing the resources
* @pdev: Handle to the platform device structure
*
* This function frees all the resources allocated to the device.
*
* Return: 0 always
*/
static int cdns_i2c_remove(struct platform_device *pdev)
{
struct cdns_i2c *id = platform_get_drvdata(pdev);
i2c_del_adapter(&id->adap);
clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
clk_disable_unprepare(id->clk);
pm_runtime_disable(&pdev->dev);
return 0;
}
static struct platform_driver cdns_i2c_drv = {
.driver = {
.name = DRIVER_NAME,
.of_match_table = cdns_i2c_of_match,
.pm = &cdns_i2c_dev_pm_ops,
},
.probe = cdns_i2c_probe,
.remove = cdns_i2c_remove,
};
module_platform_driver(cdns_i2c_drv);
MODULE_AUTHOR("Xilinx Inc.");
MODULE_DESCRIPTION("Cadence I2C bus driver");
MODULE_LICENSE("GPL");
Reference in New Issue View Git Blame Copy Permalink