83 lines
2.2 KiB
Plaintext
83 lines
2.2 KiB
Plaintext
I2C for Atmel platforms
|
|
|
|
Required properties :
|
|
- compatible : Must be one of:
|
|
"atmel,at91rm9200-i2c",
|
|
"atmel,at91sam9261-i2c",
|
|
"atmel,at91sam9260-i2c",
|
|
"atmel,at91sam9g20-i2c",
|
|
"atmel,at91sam9g10-i2c",
|
|
"atmel,at91sam9x5-i2c",
|
|
"atmel,sama5d4-i2c",
|
|
"atmel,sama5d2-i2c",
|
|
"microchip,sam9x60-i2c".
|
|
- reg: physical base address of the controller and length of memory mapped
|
|
region.
|
|
- interrupts: interrupt number to the cpu.
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
- clocks: phandles to input clocks.
|
|
|
|
Optional properties:
|
|
- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
|
|
- dmas: A list of two dma specifiers, one for each entry in dma-names.
|
|
- dma-names: should contain "tx" and "rx".
|
|
- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
|
|
capable I2C controllers.
|
|
- i2c-sda-hold-time-ns: TWD hold time, only available for:
|
|
"atmel,sama5d4-i2c",
|
|
"atmel,sama5d2-i2c",
|
|
"microchip,sam9x60-i2c".
|
|
- scl-gpios: specify the gpio related to SCL pin
|
|
- sda-gpios: specify the gpio related to SDA pin
|
|
- pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c
|
|
bus recovery, call it "gpio" state
|
|
- Child nodes conforming to i2c bus binding
|
|
|
|
|
|
Examples :
|
|
|
|
i2c0: i2c@fff84000 {
|
|
compatible = "atmel,at91sam9g20-i2c";
|
|
reg = <0xfff84000 0x100>;
|
|
interrupts = <12 4 6>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
clocks = <&twi0_clk>;
|
|
clock-frequency = <400000>;
|
|
|
|
24c512@50 {
|
|
compatible = "atmel,24c512";
|
|
reg = <0x50>;
|
|
pagesize = <128>;
|
|
}
|
|
}
|
|
|
|
i2c0: i2c@f8034600 {
|
|
compatible = "atmel,sama5d2-i2c";
|
|
reg = <0xf8034600 0x100>;
|
|
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
|
|
dmas = <&dma0
|
|
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
|
|
AT91_XDMAC_DT_PERID(11)>,
|
|
<&dma0
|
|
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
|
|
AT91_XDMAC_DT_PERID(12)>;
|
|
dma-names = "tx", "rx";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
clocks = <&flx0>;
|
|
atmel,fifo-size = <16>;
|
|
i2c-sda-hold-time-ns = <336>;
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c0>;
|
|
pinctrl-1 = <&pinctrl_i2c0_gpio>;
|
|
sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
|
|
scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
|
wm8731: wm8731@1a {
|
|
compatible = "wm8731";
|
|
reg = <0x1a>;
|
|
};
|
|
};
|