586 lines
13 KiB
Plaintext
586 lines
13 KiB
Plaintext
/*
|
|
* Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
/dts-v1/;
|
|
|
|
#include "dra72x.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/clk/ti-dra7-atl.h>
|
|
|
|
/ {
|
|
compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
|
|
|
|
aliases {
|
|
display0 = &hdmi0;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = &uart1;
|
|
};
|
|
|
|
evm_12v0: fixedregulator-evm12v0 {
|
|
/* main supply */
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "evm_12v0";
|
|
regulator-min-microvolt = <12000000>;
|
|
regulator-max-microvolt = <12000000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
evm_5v0: fixedregulator-evm5v0 {
|
|
/* Output 1 of TPS43351QDAPRQ1 on dra72-evm */
|
|
/* Output 1 of LM5140QRWGTQ1 on dra71-evm */
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "evm_5v0";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
vin-supply = <&evm_12v0>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
evm_3v6: fixedregulator-evm_3v6 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "evm_3v6";
|
|
regulator-min-microvolt = <3600000>;
|
|
regulator-max-microvolt = <3600000>;
|
|
vin-supply = <&evm_5v0>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vsys_3v3: fixedregulator-vsys3v3 {
|
|
/* Output 2 of TPS43351QDAPRQ1 on dra72-evm */
|
|
/* Output 2 of LM5140QRWGTQ1 on dra71-evm */
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vsys_3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&evm_12v0>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
evm_3v3_sw: fixedregulator-evm_3v3 {
|
|
/* TPS22965DSG */
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "evm_3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&vsys_3v3>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
aic_dvdd: fixedregulator-aic_dvdd {
|
|
/* TPS77018DBVT */
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "aic_dvdd";
|
|
vin-supply = <&evm_3v3_sw>;
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
evm_3v3_sd: fixedregulator-sd {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "evm_3v3_sd";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
vin-supply = <&evm_3v3_sw>;
|
|
enable-active-high;
|
|
gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
extcon_usb1: extcon_usb1 {
|
|
compatible = "linux,extcon-usb-gpio";
|
|
id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
extcon_usb2: extcon_usb2 {
|
|
compatible = "linux,extcon-usb-gpio";
|
|
id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
hdmi0: connector {
|
|
compatible = "hdmi-connector";
|
|
label = "hdmi";
|
|
|
|
type = "a";
|
|
|
|
port {
|
|
hdmi_connector_in: endpoint {
|
|
remote-endpoint = <&tpd12s015_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
tpd12s015: encoder {
|
|
compatible = "ti,tpd12s015";
|
|
|
|
gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
|
|
<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
|
|
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
|
|
tpd12s015_in: endpoint {
|
|
remote-endpoint = <&hdmi_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
|
|
tpd12s015_out: endpoint {
|
|
remote-endpoint = <&hdmi_connector_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
sound0: sound0 {
|
|
compatible = "simple-audio-card";
|
|
simple-audio-card,name = "DRA7xx-EVM";
|
|
simple-audio-card,widgets =
|
|
"Headphone", "Headphone Jack",
|
|
"Line", "Line Out",
|
|
"Microphone", "Mic Jack",
|
|
"Line", "Line In";
|
|
simple-audio-card,routing =
|
|
"Headphone Jack", "HPLOUT",
|
|
"Headphone Jack", "HPROUT",
|
|
"Line Out", "LLOUT",
|
|
"Line Out", "RLOUT",
|
|
"MIC3L", "Mic Jack",
|
|
"MIC3R", "Mic Jack",
|
|
"Mic Jack", "Mic Bias",
|
|
"LINE1L", "Line In",
|
|
"LINE1R", "Line In";
|
|
simple-audio-card,format = "dsp_b";
|
|
simple-audio-card,bitclock-master = <&sound0_master>;
|
|
simple-audio-card,frame-master = <&sound0_master>;
|
|
simple-audio-card,bitclock-inversion;
|
|
|
|
sound0_master: simple-audio-card,cpu {
|
|
sound-dai = <&mcasp3>;
|
|
system-clock-frequency = <5644800>;
|
|
};
|
|
|
|
simple-audio-card,codec {
|
|
sound-dai = <&tlv320aic3106>;
|
|
clocks = <&atl_clkin2_ck>;
|
|
};
|
|
};
|
|
|
|
vmmcwl_fixed: fixedregulator-mmcwl {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vmmcwl_fixed";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
};
|
|
|
|
&dra7_pmx_core {
|
|
dcan1_pins_default: dcan1_pins_default {
|
|
pinctrl-single,pins = <
|
|
DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
|
|
DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
|
|
>;
|
|
};
|
|
|
|
dcan1_pins_sleep: dcan1_pins_sleep {
|
|
pinctrl-single,pins = <
|
|
DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
|
|
DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
pcf_lcd: gpio@20 {
|
|
compatible = "nxp,pcf8575";
|
|
reg = <0x20>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pcf_gpio_21: gpio@21 {
|
|
compatible = "ti,pcf8575", "nxp,pcf8575";
|
|
reg = <0x21>;
|
|
lines-initial-states = <0x1408>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
tlv320aic3106: tlv320aic3106@19 {
|
|
#sound-dai-cells = <0>;
|
|
compatible = "ti,tlv320aic3106";
|
|
reg = <0x19>;
|
|
adc-settle-ms = <40>;
|
|
ai3x-micbias-vg = <1>; /* 2.0V */
|
|
status = "okay";
|
|
|
|
/* Regulators */
|
|
AVDD-supply = <&evm_3v3_sw>;
|
|
IOVDD-supply = <&evm_3v3_sw>;
|
|
DRVDD-supply = <&evm_3v3_sw>;
|
|
DVDD-supply = <&aic_dvdd>;
|
|
};
|
|
};
|
|
|
|
&i2c5 {
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
pcf_hdmi: pcf8575@26 {
|
|
compatible = "ti,pcf8575", "nxp,pcf8575";
|
|
reg = <0x26>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
/*
|
|
* initial state is used here to keep the mdio interface
|
|
* selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
|
|
* VIN2_S0 driven high otherwise Ethernet stops working
|
|
* VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
|
|
*/
|
|
lines-initial-states = <0x0f2b>;
|
|
|
|
p1 {
|
|
/* vin6_sel_s0: high: VIN6, low: audio */
|
|
gpio-hog;
|
|
gpios = <1 GPIO_ACTIVE_HIGH>;
|
|
output-low;
|
|
line-name = "vin6_sel_s0";
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
|
|
<&dra7_pmx_core 0x3e0>;
|
|
};
|
|
|
|
&elm {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpmc {
|
|
/*
|
|
* For the existing IOdelay configuration via U-Boot we don't
|
|
* support NAND on dra72-evm. Keep it disabled. Enabling it
|
|
* requires a different configuration by U-Boot.
|
|
*/
|
|
status = "disabled";
|
|
ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
|
|
nand@0,0 {
|
|
/* To use NAND, DIP switch SW5 must be set like so:
|
|
* SW5.1 (NAND_SELn) = ON (LOW)
|
|
* SW5.9 (GPMC_WPN) = OFF (HIGH)
|
|
*/
|
|
compatible = "ti,omap2-nand";
|
|
reg = <0 0 4>; /* device IO registers */
|
|
interrupt-parent = <&gpmc>;
|
|
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
|
|
<1 IRQ_TYPE_NONE>; /* termcount */
|
|
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
|
|
ti,nand-xfer-type = "prefetch-dma";
|
|
ti,nand-ecc-opt = "bch8";
|
|
ti,elm-id = <&elm>;
|
|
nand-bus-width = <16>;
|
|
gpmc,device-width = <2>;
|
|
gpmc,sync-clk-ps = <0>;
|
|
gpmc,cs-on-ns = <0>;
|
|
gpmc,cs-rd-off-ns = <80>;
|
|
gpmc,cs-wr-off-ns = <80>;
|
|
gpmc,adv-on-ns = <0>;
|
|
gpmc,adv-rd-off-ns = <60>;
|
|
gpmc,adv-wr-off-ns = <60>;
|
|
gpmc,we-on-ns = <10>;
|
|
gpmc,we-off-ns = <50>;
|
|
gpmc,oe-on-ns = <4>;
|
|
gpmc,oe-off-ns = <40>;
|
|
gpmc,access-ns = <40>;
|
|
gpmc,wr-access-ns = <80>;
|
|
gpmc,rd-cycle-ns = <80>;
|
|
gpmc,wr-cycle-ns = <80>;
|
|
gpmc,bus-turnaround-ns = <0>;
|
|
gpmc,cycle2cycle-delay-ns = <0>;
|
|
gpmc,clk-activation-ns = <0>;
|
|
gpmc,wr-data-mux-bus-ns = <0>;
|
|
/* MTD partition table */
|
|
/* All SPL-* partitions are sized to minimal length
|
|
* which can be independently programmable. For
|
|
* NAND flash this is equal to size of erase-block */
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
partition@0 {
|
|
label = "NAND.SPL";
|
|
reg = <0x00000000 0x000020000>;
|
|
};
|
|
partition@1 {
|
|
label = "NAND.SPL.backup1";
|
|
reg = <0x00020000 0x00020000>;
|
|
};
|
|
partition@2 {
|
|
label = "NAND.SPL.backup2";
|
|
reg = <0x00040000 0x00020000>;
|
|
};
|
|
partition@3 {
|
|
label = "NAND.SPL.backup3";
|
|
reg = <0x00060000 0x00020000>;
|
|
};
|
|
partition@4 {
|
|
label = "NAND.u-boot-spl-os";
|
|
reg = <0x00080000 0x00040000>;
|
|
};
|
|
partition@5 {
|
|
label = "NAND.u-boot";
|
|
reg = <0x000c0000 0x00100000>;
|
|
};
|
|
partition@6 {
|
|
label = "NAND.u-boot-env";
|
|
reg = <0x001c0000 0x00020000>;
|
|
};
|
|
partition@7 {
|
|
label = "NAND.u-boot-env.backup1";
|
|
reg = <0x001e0000 0x00020000>;
|
|
};
|
|
partition@8 {
|
|
label = "NAND.kernel";
|
|
reg = <0x00200000 0x00800000>;
|
|
};
|
|
partition@9 {
|
|
label = "NAND.file-system";
|
|
reg = <0x00a00000 0x0f600000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&omap_dwc3_1 {
|
|
extcon = <&extcon_usb1>;
|
|
};
|
|
|
|
&omap_dwc3_2 {
|
|
extcon = <&extcon_usb2>;
|
|
};
|
|
|
|
&usb1 {
|
|
dr_mode = "otg";
|
|
extcon = <&extcon_usb1>;
|
|
};
|
|
|
|
&usb2 {
|
|
dr_mode = "host";
|
|
extcon = <&extcon_usb2>;
|
|
};
|
|
|
|
&mmc1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc1_pins_default>;
|
|
vmmc-supply = <&evm_3v3_sd>;
|
|
bus-width = <4>;
|
|
/*
|
|
* SDCD signal is not being used here - using the fact that GPIO mode
|
|
* is a viable alternative
|
|
*/
|
|
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
|
|
max-frequency = <192000000>;
|
|
};
|
|
|
|
&mmc2 {
|
|
/* SW5-3 in ON position */
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc2_pins_default>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
max-frequency = <192000000>;
|
|
};
|
|
|
|
&mmc4 {
|
|
status = "okay";
|
|
vmmc-supply = <&evm_3v6>;
|
|
vqmmc-supply = <&vmmcwl_fixed>;
|
|
bus-width = <4>;
|
|
cap-power-off-card;
|
|
keep-power-in-suspend;
|
|
non-removable;
|
|
pinctrl-names = "default", "hs", "sdr12", "sdr25";
|
|
pinctrl-0 = <&mmc4_pins_default>;
|
|
pinctrl-1 = <&mmc4_pins_default>;
|
|
pinctrl-2 = <&mmc4_pins_default>;
|
|
pinctrl-3 = <&mmc4_pins_default>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
wifi@2 {
|
|
compatible = "ti,wl1835";
|
|
reg = <2>;
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <7 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
};
|
|
|
|
&mac {
|
|
status = "okay";
|
|
};
|
|
|
|
&dcan1 {
|
|
status = "ok";
|
|
pinctrl-names = "default", "sleep", "active";
|
|
pinctrl-0 = <&dcan1_pins_sleep>;
|
|
pinctrl-1 = <&dcan1_pins_sleep>;
|
|
pinctrl-2 = <&dcan1_pins_default>;
|
|
};
|
|
|
|
&qspi {
|
|
status = "okay";
|
|
|
|
spi-max-frequency = <76800000>;
|
|
m25p80@0 {
|
|
compatible = "s25fl256s1";
|
|
spi-max-frequency = <76800000>;
|
|
reg = <0>;
|
|
spi-tx-bus-width = <1>;
|
|
spi-rx-bus-width = <4>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/* MTD partition table.
|
|
* The ROM checks the first four physical blocks
|
|
* for a valid file to boot and the flash here is
|
|
* 64KiB block size.
|
|
*/
|
|
partition@0 {
|
|
label = "QSPI.SPL";
|
|
reg = <0x00000000 0x000010000>;
|
|
};
|
|
partition@1 {
|
|
label = "QSPI.SPL.backup1";
|
|
reg = <0x00010000 0x00010000>;
|
|
};
|
|
partition@2 {
|
|
label = "QSPI.SPL.backup2";
|
|
reg = <0x00020000 0x00010000>;
|
|
};
|
|
partition@3 {
|
|
label = "QSPI.SPL.backup3";
|
|
reg = <0x00030000 0x00010000>;
|
|
};
|
|
partition@4 {
|
|
label = "QSPI.u-boot";
|
|
reg = <0x00040000 0x00100000>;
|
|
};
|
|
partition@5 {
|
|
label = "QSPI.u-boot-spl-os";
|
|
reg = <0x00140000 0x00080000>;
|
|
};
|
|
partition@6 {
|
|
label = "QSPI.u-boot-env";
|
|
reg = <0x001c0000 0x00010000>;
|
|
};
|
|
partition@7 {
|
|
label = "QSPI.u-boot-env.backup1";
|
|
reg = <0x001d0000 0x0010000>;
|
|
};
|
|
partition@8 {
|
|
label = "QSPI.kernel";
|
|
reg = <0x001e0000 0x0800000>;
|
|
};
|
|
partition@9 {
|
|
label = "QSPI.file-system";
|
|
reg = <0x009e0000 0x01620000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&dss {
|
|
status = "ok";
|
|
};
|
|
|
|
&hdmi {
|
|
status = "ok";
|
|
|
|
port {
|
|
hdmi_out: endpoint {
|
|
remote-endpoint = <&tpd12s015_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&atl {
|
|
assigned-clocks = <&abe_dpll_sys_clk_mux>,
|
|
<&atl_clkctrl DRA7_ATL_CLKCTRL 26>,
|
|
<&dpll_abe_ck>,
|
|
<&dpll_abe_m2x2_ck>,
|
|
<&atl_clkin2_ck>;
|
|
assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
|
|
assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>;
|
|
|
|
status = "okay";
|
|
|
|
atl2 {
|
|
bws = <DRA7_ATL_WS_MCASP2_FSX>;
|
|
aws = <DRA7_ATL_WS_MCASP3_FSX>;
|
|
};
|
|
};
|
|
|
|
&mcasp3 {
|
|
#sound-dai-cells = <0>;
|
|
|
|
assigned-clocks = <&l4per_clkctrl DRA7_MCASP3_CLKCTRL 24>;
|
|
assigned-clock-parents = <&atl_clkin2_ck>;
|
|
|
|
status = "okay";
|
|
|
|
op-mode = <0>; /* MCASP_IIS_MODE */
|
|
tdm-slots = <2>;
|
|
/* 4 serializer */
|
|
serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
|
|
1 2 0 0
|
|
>;
|
|
tx-num-evt = <32>;
|
|
rx-num-evt = <32>;
|
|
};
|
|
|
|
&mailbox5 {
|
|
status = "okay";
|
|
mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
|
|
status = "okay";
|
|
};
|
|
mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&mailbox6 {
|
|
status = "okay";
|
|
mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&pcie1_rc {
|
|
status = "okay";
|
|
};
|