574 lines
14 KiB
C
574 lines
14 KiB
C
/*
|
|
* MUSB OTG controller driver for Blackfin Processors
|
|
*
|
|
* Copyright 2006-2008 Analog Devices Inc.
|
|
*
|
|
* Enter bugs at http://blackfin.uclinux.org/
|
|
*
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/init.h>
|
|
#include <linux/list.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/io.h>
|
|
#include <linux/err.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/prefetch.h>
|
|
#include <linux/usb/nop-usb-xceiv.h>
|
|
|
|
#include <asm/cacheflush.h>
|
|
|
|
#include "musb_core.h"
|
|
#include "musbhsdma.h"
|
|
#include "blackfin.h"
|
|
|
|
struct bfin_glue {
|
|
struct device *dev;
|
|
struct platform_device *musb;
|
|
};
|
|
#define glue_to_musb(g) platform_get_drvdata(g->musb)
|
|
|
|
/*
|
|
* Load an endpoint's FIFO
|
|
*/
|
|
void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
|
|
{
|
|
struct musb *musb = hw_ep->musb;
|
|
void __iomem *fifo = hw_ep->fifo;
|
|
void __iomem *epio = hw_ep->regs;
|
|
u8 epnum = hw_ep->epnum;
|
|
|
|
prefetch((u8 *)src);
|
|
|
|
musb_writew(epio, MUSB_TXCOUNT, len);
|
|
|
|
dev_dbg(musb->controller, "TX ep%d fifo %p count %d buf %p, epio %p\n",
|
|
hw_ep->epnum, fifo, len, src, epio);
|
|
|
|
dump_fifo_data(src, len);
|
|
|
|
if (!ANOMALY_05000380 && epnum != 0) {
|
|
u16 dma_reg;
|
|
|
|
flush_dcache_range((unsigned long)src,
|
|
(unsigned long)(src + len));
|
|
|
|
/* Setup DMA address register */
|
|
dma_reg = (u32)src;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
|
|
SSYNC();
|
|
|
|
dma_reg = (u32)src >> 16;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Setup DMA count register */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
|
|
SSYNC();
|
|
|
|
/* Enable the DMA */
|
|
dma_reg = (epnum << 4) | DMA_ENA | INT_ENA | DIRECTION;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Wait for compelete */
|
|
while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
|
|
cpu_relax();
|
|
|
|
/* acknowledge dma interrupt */
|
|
bfin_write_USB_DMA_INTERRUPT(1 << epnum);
|
|
SSYNC();
|
|
|
|
/* Reset DMA */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
|
|
SSYNC();
|
|
} else {
|
|
SSYNC();
|
|
|
|
if (unlikely((unsigned long)src & 0x01))
|
|
outsw_8((unsigned long)fifo, src, (len + 1) >> 1);
|
|
else
|
|
outsw((unsigned long)fifo, src, (len + 1) >> 1);
|
|
}
|
|
}
|
|
/*
|
|
* Unload an endpoint's FIFO
|
|
*/
|
|
void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
|
|
{
|
|
struct musb *musb = hw_ep->musb;
|
|
void __iomem *fifo = hw_ep->fifo;
|
|
u8 epnum = hw_ep->epnum;
|
|
|
|
if (ANOMALY_05000467 && epnum != 0) {
|
|
u16 dma_reg;
|
|
|
|
invalidate_dcache_range((unsigned long)dst,
|
|
(unsigned long)(dst + len));
|
|
|
|
/* Setup DMA address register */
|
|
dma_reg = (u32)dst;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
|
|
SSYNC();
|
|
|
|
dma_reg = (u32)dst >> 16;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Setup DMA count register */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
|
|
SSYNC();
|
|
|
|
/* Enable the DMA */
|
|
dma_reg = (epnum << 4) | DMA_ENA | INT_ENA;
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
|
|
SSYNC();
|
|
|
|
/* Wait for compelete */
|
|
while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
|
|
cpu_relax();
|
|
|
|
/* acknowledge dma interrupt */
|
|
bfin_write_USB_DMA_INTERRUPT(1 << epnum);
|
|
SSYNC();
|
|
|
|
/* Reset DMA */
|
|
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
|
|
SSYNC();
|
|
} else {
|
|
SSYNC();
|
|
/* Read the last byte of packet with odd size from address fifo + 4
|
|
* to trigger 1 byte access to EP0 FIFO.
|
|
*/
|
|
if (len == 1)
|
|
*dst = (u8)inw((unsigned long)fifo + 4);
|
|
else {
|
|
if (unlikely((unsigned long)dst & 0x01))
|
|
insw_8((unsigned long)fifo, dst, len >> 1);
|
|
else
|
|
insw((unsigned long)fifo, dst, len >> 1);
|
|
|
|
if (len & 0x01)
|
|
*(dst + len - 1) = (u8)inw((unsigned long)fifo + 4);
|
|
}
|
|
}
|
|
dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
|
|
'R', hw_ep->epnum, fifo, len, dst);
|
|
|
|
dump_fifo_data(dst, len);
|
|
}
|
|
|
|
static irqreturn_t blackfin_interrupt(int irq, void *__hci)
|
|
{
|
|
unsigned long flags;
|
|
irqreturn_t retval = IRQ_NONE;
|
|
struct musb *musb = __hci;
|
|
|
|
spin_lock_irqsave(&musb->lock, flags);
|
|
|
|
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
|
|
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
|
|
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
|
|
|
|
if (musb->int_usb || musb->int_tx || musb->int_rx) {
|
|
musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
|
|
musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
|
|
musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
|
|
retval = musb_interrupt(musb);
|
|
}
|
|
|
|
/* Start sampling ID pin, when plug is removed from MUSB */
|
|
if ((musb->xceiv->state == OTG_STATE_B_IDLE
|
|
|| musb->xceiv->state == OTG_STATE_A_WAIT_BCON) ||
|
|
(musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
|
|
musb->a_wait_bcon = TIMER_DELAY;
|
|
}
|
|
|
|
spin_unlock_irqrestore(&musb->lock, flags);
|
|
|
|
return retval;
|
|
}
|
|
|
|
static void musb_conn_timer_handler(unsigned long _musb)
|
|
{
|
|
struct musb *musb = (void *)_musb;
|
|
unsigned long flags;
|
|
u16 val;
|
|
static u8 toggle;
|
|
|
|
spin_lock_irqsave(&musb->lock, flags);
|
|
switch (musb->xceiv->state) {
|
|
case OTG_STATE_A_IDLE:
|
|
case OTG_STATE_A_WAIT_BCON:
|
|
/* Start a new session */
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
val &= ~MUSB_DEVCTL_SESSION;
|
|
musb_writew(musb->mregs, MUSB_DEVCTL, val);
|
|
val |= MUSB_DEVCTL_SESSION;
|
|
musb_writew(musb->mregs, MUSB_DEVCTL, val);
|
|
/* Check if musb is host or peripheral. */
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
|
|
if (!(val & MUSB_DEVCTL_BDEVICE)) {
|
|
gpio_set_value(musb->config->gpio_vrsel, 1);
|
|
musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
|
|
} else {
|
|
gpio_set_value(musb->config->gpio_vrsel, 0);
|
|
/* Ignore VBUSERROR and SUSPEND IRQ */
|
|
val = musb_readb(musb->mregs, MUSB_INTRUSBE);
|
|
val &= ~MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
|
|
|
|
val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSB, val);
|
|
musb->xceiv->state = OTG_STATE_B_IDLE;
|
|
}
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
|
|
break;
|
|
case OTG_STATE_B_IDLE:
|
|
/*
|
|
* Start a new session. It seems that MUSB needs taking
|
|
* some time to recognize the type of the plug inserted?
|
|
*/
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
val |= MUSB_DEVCTL_SESSION;
|
|
musb_writew(musb->mregs, MUSB_DEVCTL, val);
|
|
val = musb_readw(musb->mregs, MUSB_DEVCTL);
|
|
|
|
if (!(val & MUSB_DEVCTL_BDEVICE)) {
|
|
gpio_set_value(musb->config->gpio_vrsel, 1);
|
|
musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
|
|
} else {
|
|
gpio_set_value(musb->config->gpio_vrsel, 0);
|
|
|
|
/* Ignore VBUSERROR and SUSPEND IRQ */
|
|
val = musb_readb(musb->mregs, MUSB_INTRUSBE);
|
|
val &= ~MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
|
|
|
|
val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
|
|
musb_writeb(musb->mregs, MUSB_INTRUSB, val);
|
|
|
|
/* Toggle the Soft Conn bit, so that we can response to
|
|
* the inserting of either A-plug or B-plug.
|
|
*/
|
|
if (toggle) {
|
|
val = musb_readb(musb->mregs, MUSB_POWER);
|
|
val &= ~MUSB_POWER_SOFTCONN;
|
|
musb_writeb(musb->mregs, MUSB_POWER, val);
|
|
toggle = 0;
|
|
} else {
|
|
val = musb_readb(musb->mregs, MUSB_POWER);
|
|
val |= MUSB_POWER_SOFTCONN;
|
|
musb_writeb(musb->mregs, MUSB_POWER, val);
|
|
toggle = 1;
|
|
}
|
|
/* The delay time is set to 1/4 second by default,
|
|
* shortening it, if accelerating A-plug detection
|
|
* is needed in OTG mode.
|
|
*/
|
|
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY / 4);
|
|
}
|
|
break;
|
|
default:
|
|
dev_dbg(musb->controller, "%s state not handled\n",
|
|
otg_state_string(musb->xceiv->state));
|
|
break;
|
|
}
|
|
spin_unlock_irqrestore(&musb->lock, flags);
|
|
|
|
dev_dbg(musb->controller, "state is %s\n",
|
|
otg_state_string(musb->xceiv->state));
|
|
}
|
|
|
|
static void bfin_musb_enable(struct musb *musb)
|
|
{
|
|
/* REVISIT is this really correct ? */
|
|
}
|
|
|
|
static void bfin_musb_disable(struct musb *musb)
|
|
{
|
|
}
|
|
|
|
static void bfin_musb_set_vbus(struct musb *musb, int is_on)
|
|
{
|
|
int value = musb->config->gpio_vrsel_active;
|
|
if (!is_on)
|
|
value = !value;
|
|
gpio_set_value(musb->config->gpio_vrsel, value);
|
|
|
|
dev_dbg(musb->controller, "VBUS %s, devctl %02x "
|
|
/* otg %3x conf %08x prcm %08x */ "\n",
|
|
otg_state_string(musb->xceiv->state),
|
|
musb_readb(musb->mregs, MUSB_DEVCTL));
|
|
}
|
|
|
|
static int bfin_musb_set_power(struct usb_phy *x, unsigned mA)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int bfin_musb_vbus_status(struct musb *musb)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int bfin_musb_set_mode(struct musb *musb, u8 musb_mode)
|
|
{
|
|
return -EIO;
|
|
}
|
|
|
|
static int bfin_musb_adjust_channel_params(struct dma_channel *channel,
|
|
u16 packet_sz, u8 *mode,
|
|
dma_addr_t *dma_addr, u32 *len)
|
|
{
|
|
struct musb_dma_channel *musb_channel = channel->private_data;
|
|
|
|
/*
|
|
* Anomaly 05000450 might cause data corruption when using DMA
|
|
* MODE 1 transmits with short packet. So to work around this,
|
|
* we truncate all MODE 1 transfers down to a multiple of the
|
|
* max packet size, and then do the last short packet transfer
|
|
* (if there is any) using MODE 0.
|
|
*/
|
|
if (ANOMALY_05000450) {
|
|
if (musb_channel->transmit && *mode == 1)
|
|
*len = *len - (*len % packet_sz);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void bfin_musb_reg_init(struct musb *musb)
|
|
{
|
|
if (ANOMALY_05000346) {
|
|
bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
|
|
SSYNC();
|
|
}
|
|
|
|
if (ANOMALY_05000347) {
|
|
bfin_write_USB_APHY_CNTRL(0x0);
|
|
SSYNC();
|
|
}
|
|
|
|
/* Configure PLL oscillator register */
|
|
bfin_write_USB_PLLOSC_CTRL(0x3080 |
|
|
((480/musb->config->clkin) << 1));
|
|
SSYNC();
|
|
|
|
bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
|
|
SSYNC();
|
|
|
|
bfin_write_USB_EP_NI0_RXMAXP(64);
|
|
SSYNC();
|
|
|
|
bfin_write_USB_EP_NI0_TXMAXP(64);
|
|
SSYNC();
|
|
|
|
/* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/
|
|
bfin_write_USB_GLOBINTR(0x7);
|
|
SSYNC();
|
|
|
|
bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA |
|
|
EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA |
|
|
EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA |
|
|
EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
|
|
EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
|
|
SSYNC();
|
|
}
|
|
|
|
static int bfin_musb_init(struct musb *musb)
|
|
{
|
|
|
|
/*
|
|
* Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
|
|
* and OTG HOST modes, while rev 1.1 and greater require PE7 to
|
|
* be low for DEVICE mode and high for HOST mode. We set it high
|
|
* here because we are in host mode
|
|
*/
|
|
|
|
if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
|
|
printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
|
|
musb->config->gpio_vrsel);
|
|
return -ENODEV;
|
|
}
|
|
gpio_direction_output(musb->config->gpio_vrsel, 0);
|
|
|
|
usb_nop_xceiv_register();
|
|
musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
|
|
if (IS_ERR_OR_NULL(musb->xceiv)) {
|
|
gpio_free(musb->config->gpio_vrsel);
|
|
return -EPROBE_DEFER;
|
|
}
|
|
|
|
bfin_musb_reg_init(musb);
|
|
|
|
setup_timer(&musb_conn_timer, musb_conn_timer_handler,
|
|
(unsigned long) musb);
|
|
|
|
musb->xceiv->set_power = bfin_musb_set_power;
|
|
|
|
musb->isr = blackfin_interrupt;
|
|
musb->double_buffer_not_ok = true;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int bfin_musb_exit(struct musb *musb)
|
|
{
|
|
gpio_free(musb->config->gpio_vrsel);
|
|
|
|
usb_put_phy(musb->xceiv);
|
|
usb_nop_xceiv_unregister();
|
|
return 0;
|
|
}
|
|
|
|
static const struct musb_platform_ops bfin_ops = {
|
|
.init = bfin_musb_init,
|
|
.exit = bfin_musb_exit,
|
|
|
|
.enable = bfin_musb_enable,
|
|
.disable = bfin_musb_disable,
|
|
|
|
.set_mode = bfin_musb_set_mode,
|
|
|
|
.vbus_status = bfin_musb_vbus_status,
|
|
.set_vbus = bfin_musb_set_vbus,
|
|
|
|
.adjust_channel_params = bfin_musb_adjust_channel_params,
|
|
};
|
|
|
|
static u64 bfin_dmamask = DMA_BIT_MASK(32);
|
|
|
|
static int bfin_probe(struct platform_device *pdev)
|
|
{
|
|
struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
|
|
struct platform_device *musb;
|
|
struct bfin_glue *glue;
|
|
|
|
int ret = -ENOMEM;
|
|
|
|
glue = kzalloc(sizeof(*glue), GFP_KERNEL);
|
|
if (!glue) {
|
|
dev_err(&pdev->dev, "failed to allocate glue context\n");
|
|
goto err0;
|
|
}
|
|
|
|
musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO);
|
|
if (!musb) {
|
|
dev_err(&pdev->dev, "failed to allocate musb device\n");
|
|
goto err1;
|
|
}
|
|
|
|
musb->dev.parent = &pdev->dev;
|
|
musb->dev.dma_mask = &bfin_dmamask;
|
|
musb->dev.coherent_dma_mask = bfin_dmamask;
|
|
|
|
glue->dev = &pdev->dev;
|
|
glue->musb = musb;
|
|
|
|
pdata->platform_ops = &bfin_ops;
|
|
|
|
platform_set_drvdata(pdev, glue);
|
|
|
|
ret = platform_device_add_resources(musb, pdev->resource,
|
|
pdev->num_resources);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to add resources\n");
|
|
goto err3;
|
|
}
|
|
|
|
ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to add platform_data\n");
|
|
goto err3;
|
|
}
|
|
|
|
ret = platform_device_add(musb);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to register musb device\n");
|
|
goto err3;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err3:
|
|
platform_device_put(musb);
|
|
|
|
err1:
|
|
kfree(glue);
|
|
|
|
err0:
|
|
return ret;
|
|
}
|
|
|
|
static int bfin_remove(struct platform_device *pdev)
|
|
{
|
|
struct bfin_glue *glue = platform_get_drvdata(pdev);
|
|
|
|
platform_device_unregister(glue->musb);
|
|
kfree(glue);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int bfin_suspend(struct device *dev)
|
|
{
|
|
struct bfin_glue *glue = dev_get_drvdata(dev);
|
|
struct musb *musb = glue_to_musb(glue);
|
|
|
|
if (is_host_active(musb))
|
|
/*
|
|
* During hibernate gpio_vrsel will change from high to low
|
|
* low which will generate wakeup event resume the system
|
|
* immediately. Set it to 0 before hibernate to avoid this
|
|
* wakeup event.
|
|
*/
|
|
gpio_set_value(musb->config->gpio_vrsel, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int bfin_resume(struct device *dev)
|
|
{
|
|
struct bfin_glue *glue = dev_get_drvdata(dev);
|
|
struct musb *musb = glue_to_musb(glue);
|
|
|
|
bfin_musb_reg_init(musb);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct dev_pm_ops bfin_pm_ops = {
|
|
.suspend = bfin_suspend,
|
|
.resume = bfin_resume,
|
|
};
|
|
|
|
#define DEV_PM_OPS &bfin_pm_ops
|
|
#else
|
|
#define DEV_PM_OPS NULL
|
|
#endif
|
|
|
|
static struct platform_driver bfin_driver = {
|
|
.probe = bfin_probe,
|
|
.remove = __exit_p(bfin_remove),
|
|
.driver = {
|
|
.name = "musb-blackfin",
|
|
.pm = DEV_PM_OPS,
|
|
},
|
|
};
|
|
|
|
MODULE_DESCRIPTION("Blackfin MUSB Glue Layer");
|
|
MODULE_AUTHOR("Bryan Wy <cooloney@kernel.org>");
|
|
MODULE_LICENSE("GPL v2");
|
|
module_platform_driver(bfin_driver);
|