126 lines
5.9 KiB
Plaintext
126 lines
5.9 KiB
Plaintext
fmc-write-eeprom
|
|
================
|
|
|
|
This module is designed to load a binary file from /lib/firmware and to
|
|
write it to the internal EEPROM of the mezzanine card. This driver uses
|
|
the `busid' generic parameter.
|
|
|
|
Overwriting the EEPROM is not something you should do daily, and it is
|
|
expected to only happen during manufacturing. For this reason, the
|
|
module makes it unlikely for the random user to change a working EEPROM.
|
|
|
|
The module takes the following measures:
|
|
|
|
* It accepts a `file=' argument (within /lib/firmware) and if no
|
|
such argument is received, it doesn't write anything to EEPROM
|
|
(i.e. there is no default file name).
|
|
|
|
* If the file name ends with `.bin' it is written verbatim starting
|
|
at offset 0.
|
|
|
|
* If the file name ends with `.tlv' it is interpreted as
|
|
type-length-value (i.e., it allows writev(2)-like operation).
|
|
|
|
* If the file name doesn't match any of the patterns above, it is
|
|
ignored and no write is performed.
|
|
|
|
* Only cards listed with `busid=' are written to. If no busid is
|
|
specified, no programming is done (and the probe function of the
|
|
driver will fail).
|
|
|
|
|
|
Each TLV tuple is formatted in this way: the header is 5 bytes,
|
|
followed by data. The first byte is `w' for write, the next two bytes
|
|
represent the address, in little-endian byte order, and the next two
|
|
represent the data length, in little-endian order. The length does not
|
|
include the header (it is the actual number of bytes to be written).
|
|
|
|
This is a real example: that writes 5 bytes at position 0x110:
|
|
|
|
spusa.root# od -t x1 -Ax /lib/firmware/try.tlv
|
|
000000 77 10 01 05 00 30 31 32 33 34
|
|
00000a
|
|
spusa.root# insmod /tmp/fmc-write-eeprom.ko busid=0x0200 file=try.tlv
|
|
[19983.391498] spec 0000:03:00.0: write 5 bytes at 0x0110
|
|
[19983.414615] spec 0000:03:00.0: write_eeprom: success
|
|
|
|
Please note that you'll most likely want to use SDBFS to build your
|
|
EEPROM image, at least if your mezzanines are being used in the White
|
|
Rabbit environment. For this reason the TLV format is not expected to
|
|
be used much and is not expected to be developed further.
|
|
|
|
If you want to try reflashing fake EEPROM devices, you can use the
|
|
fmc-fakedev.ko module (see *note fmc-fakedev::). Whenever you change
|
|
the image starting at offset 0, it will deregister and register again
|
|
after two seconds. Please note, however, that if fmc-write-eeprom is
|
|
still loaded, the system will associate it to the new device, which
|
|
will be reprogrammed and thus will be unloaded after two seconds. The
|
|
following example removes the module after it reflashed fakedev the
|
|
first time.
|
|
|
|
spusa.root# insmod fmc-fakedev.ko
|
|
[ 72.984733] fake-fmc: Manufacturer: fake-vendor
|
|
[ 72.989434] fake-fmc: Product name: fake-design-for-testing
|
|
spusa.root# insmod fmc-write-eeprom.ko busid=0 file=fdelay-eeprom.bin; \
|
|
rmmod fmc-write-eeprom
|
|
[ 130.874098] fake-fmc: Matching a generic driver (no ID)
|
|
[ 130.887845] fake-fmc: programming 6155 bytes
|
|
[ 130.894567] fake-fmc: write_eeprom: success
|
|
[ 132.895794] fake-fmc: Manufacturer: CERN
|
|
[ 132.899872] fake-fmc: Product name: FmcDelay1ns4cha
|
|
|
|
|
|
Writing to the EEPROM
|
|
=====================
|
|
|
|
Once you have created a binary file for your EEPROM, you can write it
|
|
to the storage medium using the fmc-write-eeprom (See *note
|
|
fmc-write-eeprom::, while relying on a carrier driver. The procedure
|
|
here shown here uses the SPEC driver
|
|
(`http://www.ohwr.org/projects/spec-sw').
|
|
|
|
The example assumes no driver is already loaded (actually, I unloaded
|
|
them by hand as everything loads automatically at boot time after you
|
|
installed the modules), and shows kernel messages together with
|
|
commands. Here the prompt is spusa.root# and two SPEC cards are plugged
|
|
in the system.
|
|
|
|
spusa.root# insmod fmc.ko
|
|
spusa.root# insmod spec.ko
|
|
[13972.382818] spec 0000:02:00.0: probe for device 0002:0000
|
|
[13972.392773] spec 0000:02:00.0: got file "fmc/spec-init.bin", 1484404 (0x16a674) bytes
|
|
[13972.591388] spec 0000:02:00.0: FPGA programming successful
|
|
[13972.883011] spec 0000:02:00.0: EEPROM has no FRU information
|
|
[13972.888719] spec 0000:02:00.0: No device_id filled, using index
|
|
[13972.894676] spec 0000:02:00.0: No mezzanine_name found
|
|
[13972.899863] /home/rubini/wip/spec-sw/kernel/spec-gpio.c - spec_gpio_init
|
|
[13972.906578] spec 0000:04:00.0: probe for device 0004:0000
|
|
[13972.916509] spec 0000:04:00.0: got file "fmc/spec-init.bin", 1484404 (0x16a674) bytes
|
|
[13973.115096] spec 0000:04:00.0: FPGA programming successful
|
|
[13973.401798] spec 0000:04:00.0: EEPROM has no FRU information
|
|
[13973.407474] spec 0000:04:00.0: No device_id filled, using index
|
|
[13973.413417] spec 0000:04:00.0: No mezzanine_name found
|
|
[13973.418600] /home/rubini/wip/spec-sw/kernel/spec-gpio.c - spec_gpio_init
|
|
spusa.root# ls /sys/bus/fmc/devices
|
|
fmc-0000 fmc-0001
|
|
spusa.root# insmod fmc-write-eeprom.ko busid=0x0200 file=fdelay-eeprom.bin
|
|
[14103.966259] spec 0000:02:00.0: Matching an generic driver (no ID)
|
|
[14103.975519] spec 0000:02:00.0: programming 6155 bytes
|
|
[14126.373762] spec 0000:02:00.0: write_eeprom: success
|
|
[14126.378770] spec 0000:04:00.0: Matching an generic driver (no ID)
|
|
[14126.384903] spec 0000:04:00.0: fmc_write_eeprom: no filename given: not programming
|
|
[14126.392600] fmc_write_eeprom: probe of fmc-0001 failed with error -2
|
|
|
|
Reading back the EEPROM
|
|
=======================
|
|
|
|
In order to read back the binary content of the EEPROM of your
|
|
mezzanine device, the bus creates a read-only sysfs file called eeprom
|
|
for each mezzanine it knows about:
|
|
|
|
spusa.root# cd /sys/bus/fmc/devices; ls -l */eeprom
|
|
-r--r--r-- 1 root root 8192 Apr 9 16:53 FmcDelay1ns4cha-f001/eeprom
|
|
-r--r--r-- 1 root root 8192 Apr 9 17:19 fake-design-for-testing-f002/eeprom
|
|
-r--r--r-- 1 root root 8192 Apr 9 17:19 fake-design-for-testing-f003/eeprom
|
|
-r--r--r-- 1 root root 8192 Apr 9 17:19 fmc-f004/eeprom
|