462 lines
12 KiB
C
462 lines
12 KiB
C
#include <linux/init.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/pci.h>
|
|
#include <asm/dma.h>
|
|
#include <linux/io.h>
|
|
#include <asm/processor-cyrix.h>
|
|
#include <asm/processor-flags.h>
|
|
#include <linux/timer.h>
|
|
#include <asm/pci-direct.h>
|
|
#include <asm/tsc.h>
|
|
|
|
#include "cpu.h"
|
|
|
|
/*
|
|
* Read NSC/Cyrix DEVID registers (DIR) to get more detailed info. about the CPU
|
|
*/
|
|
static void __cpuinit __do_cyrix_devid(unsigned char *dir0, unsigned char *dir1)
|
|
{
|
|
unsigned char ccr2, ccr3;
|
|
|
|
/* we test for DEVID by checking whether CCR3 is writable */
|
|
ccr3 = getCx86(CX86_CCR3);
|
|
setCx86(CX86_CCR3, ccr3 ^ 0x80);
|
|
getCx86(0xc0); /* dummy to change bus */
|
|
|
|
if (getCx86(CX86_CCR3) == ccr3) { /* no DEVID regs. */
|
|
ccr2 = getCx86(CX86_CCR2);
|
|
setCx86(CX86_CCR2, ccr2 ^ 0x04);
|
|
getCx86(0xc0); /* dummy */
|
|
|
|
if (getCx86(CX86_CCR2) == ccr2) /* old Cx486SLC/DLC */
|
|
*dir0 = 0xfd;
|
|
else { /* Cx486S A step */
|
|
setCx86(CX86_CCR2, ccr2);
|
|
*dir0 = 0xfe;
|
|
}
|
|
} else {
|
|
setCx86(CX86_CCR3, ccr3); /* restore CCR3 */
|
|
|
|
/* read DIR0 and DIR1 CPU registers */
|
|
*dir0 = getCx86(CX86_DIR0);
|
|
*dir1 = getCx86(CX86_DIR1);
|
|
}
|
|
}
|
|
|
|
static void __cpuinit do_cyrix_devid(unsigned char *dir0, unsigned char *dir1)
|
|
{
|
|
unsigned long flags;
|
|
|
|
local_irq_save(flags);
|
|
__do_cyrix_devid(dir0, dir1);
|
|
local_irq_restore(flags);
|
|
}
|
|
/*
|
|
* Cx86_dir0_msb is a HACK needed by check_cx686_cpuid/slop in bugs.h in
|
|
* order to identify the Cyrix CPU model after we're out of setup.c
|
|
*
|
|
* Actually since bugs.h doesn't even reference this perhaps someone should
|
|
* fix the documentation ???
|
|
*/
|
|
static unsigned char Cx86_dir0_msb __cpuinitdata = 0;
|
|
|
|
static const char __cpuinitconst Cx86_model[][9] = {
|
|
"Cx486", "Cx486", "5x86 ", "6x86", "MediaGX ", "6x86MX ",
|
|
"M II ", "Unknown"
|
|
};
|
|
static const char __cpuinitconst Cx486_name[][5] = {
|
|
"SLC", "DLC", "SLC2", "DLC2", "SRx", "DRx",
|
|
"SRx2", "DRx2"
|
|
};
|
|
static const char __cpuinitconst Cx486S_name[][4] = {
|
|
"S", "S2", "Se", "S2e"
|
|
};
|
|
static const char __cpuinitconst Cx486D_name[][4] = {
|
|
"DX", "DX2", "?", "?", "?", "DX4"
|
|
};
|
|
static char Cx86_cb[] __cpuinitdata = "?.5x Core/Bus Clock";
|
|
static const char __cpuinitconst cyrix_model_mult1[] = "12??43";
|
|
static const char __cpuinitconst cyrix_model_mult2[] = "12233445";
|
|
|
|
/*
|
|
* Reset the slow-loop (SLOP) bit on the 686(L) which is set by some old
|
|
* BIOSes for compatibility with DOS games. This makes the udelay loop
|
|
* work correctly, and improves performance.
|
|
*
|
|
* FIXME: our newer udelay uses the tsc. We don't need to frob with SLOP
|
|
*/
|
|
|
|
static void __cpuinit check_cx686_slop(struct cpuinfo_x86 *c)
|
|
{
|
|
unsigned long flags;
|
|
|
|
if (Cx86_dir0_msb == 3) {
|
|
unsigned char ccr3, ccr5;
|
|
|
|
local_irq_save(flags);
|
|
ccr3 = getCx86(CX86_CCR3);
|
|
setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */
|
|
ccr5 = getCx86(CX86_CCR5);
|
|
if (ccr5 & 2)
|
|
setCx86(CX86_CCR5, ccr5 & 0xfd); /* reset SLOP */
|
|
setCx86(CX86_CCR3, ccr3); /* disable MAPEN */
|
|
local_irq_restore(flags);
|
|
|
|
if (ccr5 & 2) { /* possible wrong calibration done */
|
|
printk(KERN_INFO "Recalibrating delay loop with SLOP bit reset\n");
|
|
calibrate_delay();
|
|
c->loops_per_jiffy = loops_per_jiffy;
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
static void __cpuinit set_cx86_reorder(void)
|
|
{
|
|
u8 ccr3;
|
|
|
|
printk(KERN_INFO "Enable Memory access reorder on Cyrix/NSC processor.\n");
|
|
ccr3 = getCx86(CX86_CCR3);
|
|
setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */
|
|
|
|
/* Load/Store Serialize to mem access disable (=reorder it) */
|
|
setCx86_old(CX86_PCR0, getCx86_old(CX86_PCR0) & ~0x80);
|
|
/* set load/store serialize from 1GB to 4GB */
|
|
ccr3 |= 0xe0;
|
|
setCx86(CX86_CCR3, ccr3);
|
|
}
|
|
|
|
static void __cpuinit set_cx86_memwb(void)
|
|
{
|
|
printk(KERN_INFO "Enable Memory-Write-back mode on Cyrix/NSC processor.\n");
|
|
|
|
/* CCR2 bit 2: unlock NW bit */
|
|
setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) & ~0x04);
|
|
/* set 'Not Write-through' */
|
|
write_cr0(read_cr0() | X86_CR0_NW);
|
|
/* CCR2 bit 2: lock NW bit and set WT1 */
|
|
setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x14);
|
|
}
|
|
|
|
/*
|
|
* Configure later MediaGX and/or Geode processor.
|
|
*/
|
|
|
|
static void __cpuinit geode_configure(void)
|
|
{
|
|
unsigned long flags;
|
|
u8 ccr3;
|
|
local_irq_save(flags);
|
|
|
|
/* Suspend on halt power saving and enable #SUSP pin */
|
|
setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x88);
|
|
|
|
ccr3 = getCx86(CX86_CCR3);
|
|
setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */
|
|
|
|
|
|
/* FPU fast, DTE cache, Mem bypass */
|
|
setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x38);
|
|
setCx86(CX86_CCR3, ccr3); /* disable MAPEN */
|
|
|
|
set_cx86_memwb();
|
|
set_cx86_reorder();
|
|
|
|
local_irq_restore(flags);
|
|
}
|
|
|
|
static void __cpuinit early_init_cyrix(struct cpuinfo_x86 *c)
|
|
{
|
|
unsigned char dir0, dir0_msn, dir1 = 0;
|
|
|
|
__do_cyrix_devid(&dir0, &dir1);
|
|
dir0_msn = dir0 >> 4; /* identifies CPU "family" */
|
|
|
|
switch (dir0_msn) {
|
|
case 3: /* 6x86/6x86L */
|
|
/* Emulate MTRRs using Cyrix's ARRs. */
|
|
set_cpu_cap(c, X86_FEATURE_CYRIX_ARR);
|
|
break;
|
|
case 5: /* 6x86MX/M II */
|
|
/* Emulate MTRRs using Cyrix's ARRs. */
|
|
set_cpu_cap(c, X86_FEATURE_CYRIX_ARR);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void __cpuinit init_cyrix(struct cpuinfo_x86 *c)
|
|
{
|
|
unsigned char dir0, dir0_msn, dir0_lsn, dir1 = 0;
|
|
char *buf = c->x86_model_id;
|
|
const char *p = NULL;
|
|
|
|
/*
|
|
* Bit 31 in normal CPUID used for nonstandard 3DNow ID;
|
|
* 3DNow is IDd by bit 31 in extended CPUID (1*32+31) anyway
|
|
*/
|
|
clear_cpu_cap(c, 0*32+31);
|
|
|
|
/* Cyrix used bit 24 in extended (AMD) CPUID for Cyrix MMX extensions */
|
|
if (test_cpu_cap(c, 1*32+24)) {
|
|
clear_cpu_cap(c, 1*32+24);
|
|
set_cpu_cap(c, X86_FEATURE_CXMMX);
|
|
}
|
|
|
|
do_cyrix_devid(&dir0, &dir1);
|
|
|
|
check_cx686_slop(c);
|
|
|
|
Cx86_dir0_msb = dir0_msn = dir0 >> 4; /* identifies CPU "family" */
|
|
dir0_lsn = dir0 & 0xf; /* model or clock multiplier */
|
|
|
|
/* common case step number/rev -- exceptions handled below */
|
|
c->x86_model = (dir1 >> 4) + 1;
|
|
c->x86_mask = dir1 & 0xf;
|
|
|
|
/* Now cook; the original recipe is by Channing Corn, from Cyrix.
|
|
* We do the same thing for each generation: we work out
|
|
* the model, multiplier and stepping. Black magic included,
|
|
* to make the silicon step/rev numbers match the printed ones.
|
|
*/
|
|
|
|
switch (dir0_msn) {
|
|
unsigned char tmp;
|
|
|
|
case 0: /* Cx486SLC/DLC/SRx/DRx */
|
|
p = Cx486_name[dir0_lsn & 7];
|
|
break;
|
|
|
|
case 1: /* Cx486S/DX/DX2/DX4 */
|
|
p = (dir0_lsn & 8) ? Cx486D_name[dir0_lsn & 5]
|
|
: Cx486S_name[dir0_lsn & 3];
|
|
break;
|
|
|
|
case 2: /* 5x86 */
|
|
Cx86_cb[2] = cyrix_model_mult1[dir0_lsn & 5];
|
|
p = Cx86_cb+2;
|
|
break;
|
|
|
|
case 3: /* 6x86/6x86L */
|
|
Cx86_cb[1] = ' ';
|
|
Cx86_cb[2] = cyrix_model_mult1[dir0_lsn & 5];
|
|
if (dir1 > 0x21) { /* 686L */
|
|
Cx86_cb[0] = 'L';
|
|
p = Cx86_cb;
|
|
(c->x86_model)++;
|
|
} else /* 686 */
|
|
p = Cx86_cb+1;
|
|
/* Emulate MTRRs using Cyrix's ARRs. */
|
|
set_cpu_cap(c, X86_FEATURE_CYRIX_ARR);
|
|
/* 6x86's contain this bug */
|
|
c->coma_bug = 1;
|
|
break;
|
|
|
|
case 4: /* MediaGX/GXm or Geode GXM/GXLV/GX1 */
|
|
#ifdef CONFIG_PCI
|
|
{
|
|
u32 vendor, device;
|
|
/*
|
|
* It isn't really a PCI quirk directly, but the cure is the
|
|
* same. The MediaGX has deep magic SMM stuff that handles the
|
|
* SB emulation. It throws away the fifo on disable_dma() which
|
|
* is wrong and ruins the audio.
|
|
*
|
|
* Bug2: VSA1 has a wrap bug so that using maximum sized DMA
|
|
* causes bad things. According to NatSemi VSA2 has another
|
|
* bug to do with 'hlt'. I've not seen any boards using VSA2
|
|
* and X doesn't seem to support it either so who cares 8).
|
|
* VSA1 we work around however.
|
|
*/
|
|
|
|
printk(KERN_INFO "Working around Cyrix MediaGX virtual DMA bugs.\n");
|
|
isa_dma_bridge_buggy = 2;
|
|
|
|
/* We do this before the PCI layer is running. However we
|
|
are safe here as we know the bridge must be a Cyrix
|
|
companion and must be present */
|
|
vendor = read_pci_config_16(0, 0, 0x12, PCI_VENDOR_ID);
|
|
device = read_pci_config_16(0, 0, 0x12, PCI_DEVICE_ID);
|
|
|
|
/*
|
|
* The 5510/5520 companion chips have a funky PIT.
|
|
*/
|
|
if (vendor == PCI_VENDOR_ID_CYRIX &&
|
|
(device == PCI_DEVICE_ID_CYRIX_5510 ||
|
|
device == PCI_DEVICE_ID_CYRIX_5520))
|
|
mark_tsc_unstable("cyrix 5510/5520 detected");
|
|
}
|
|
#endif
|
|
c->x86_cache_size = 16; /* Yep 16K integrated cache thats it */
|
|
|
|
/* GXm supports extended cpuid levels 'ala' AMD */
|
|
if (c->cpuid_level == 2) {
|
|
/* Enable cxMMX extensions (GX1 Datasheet 54) */
|
|
setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7) | 1);
|
|
|
|
/*
|
|
* GXm : 0x30 ... 0x5f GXm datasheet 51
|
|
* GXlv: 0x6x GXlv datasheet 54
|
|
* ? : 0x7x
|
|
* GX1 : 0x8x GX1 datasheet 56
|
|
*/
|
|
if ((0x30 <= dir1 && dir1 <= 0x6f) ||
|
|
(0x80 <= dir1 && dir1 <= 0x8f))
|
|
geode_configure();
|
|
return;
|
|
} else { /* MediaGX */
|
|
Cx86_cb[2] = (dir0_lsn & 1) ? '3' : '4';
|
|
p = Cx86_cb+2;
|
|
c->x86_model = (dir1 & 0x20) ? 1 : 2;
|
|
}
|
|
break;
|
|
|
|
case 5: /* 6x86MX/M II */
|
|
if (dir1 > 7) {
|
|
dir0_msn++; /* M II */
|
|
/* Enable MMX extensions (App note 108) */
|
|
setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7)|1);
|
|
} else {
|
|
c->coma_bug = 1; /* 6x86MX, it has the bug. */
|
|
}
|
|
tmp = (!(dir0_lsn & 7) || dir0_lsn & 1) ? 2 : 0;
|
|
Cx86_cb[tmp] = cyrix_model_mult2[dir0_lsn & 7];
|
|
p = Cx86_cb+tmp;
|
|
if (((dir1 & 0x0f) > 4) || ((dir1 & 0xf0) == 0x20))
|
|
(c->x86_model)++;
|
|
/* Emulate MTRRs using Cyrix's ARRs. */
|
|
set_cpu_cap(c, X86_FEATURE_CYRIX_ARR);
|
|
break;
|
|
|
|
case 0xf: /* Cyrix 486 without DEVID registers */
|
|
switch (dir0_lsn) {
|
|
case 0xd: /* either a 486SLC or DLC w/o DEVID */
|
|
dir0_msn = 0;
|
|
p = Cx486_name[(c->hard_math) ? 1 : 0];
|
|
break;
|
|
|
|
case 0xe: /* a 486S A step */
|
|
dir0_msn = 0;
|
|
p = Cx486S_name[0];
|
|
break;
|
|
}
|
|
break;
|
|
|
|
default: /* unknown (shouldn't happen, we know everyone ;-) */
|
|
dir0_msn = 7;
|
|
break;
|
|
}
|
|
strcpy(buf, Cx86_model[dir0_msn & 7]);
|
|
if (p)
|
|
strcat(buf, p);
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Handle National Semiconductor branded processors
|
|
*/
|
|
static void __cpuinit init_nsc(struct cpuinfo_x86 *c)
|
|
{
|
|
/*
|
|
* There may be GX1 processors in the wild that are branded
|
|
* NSC and not Cyrix.
|
|
*
|
|
* This function only handles the GX processor, and kicks every
|
|
* thing else to the Cyrix init function above - that should
|
|
* cover any processors that might have been branded differently
|
|
* after NSC acquired Cyrix.
|
|
*
|
|
* If this breaks your GX1 horribly, please e-mail
|
|
* info-linux@ldcmail.amd.com to tell us.
|
|
*/
|
|
|
|
/* Handle the GX (Formally known as the GX2) */
|
|
|
|
if (c->x86 == 5 && c->x86_model == 5)
|
|
cpu_detect_cache_sizes(c);
|
|
else
|
|
init_cyrix(c);
|
|
}
|
|
|
|
/*
|
|
* Cyrix CPUs without cpuid or with cpuid not yet enabled can be detected
|
|
* by the fact that they preserve the flags across the division of 5/2.
|
|
* PII and PPro exhibit this behavior too, but they have cpuid available.
|
|
*/
|
|
|
|
/*
|
|
* Perform the Cyrix 5/2 test. A Cyrix won't change
|
|
* the flags, while other 486 chips will.
|
|
*/
|
|
static inline int test_cyrix_52div(void)
|
|
{
|
|
unsigned int test;
|
|
|
|
__asm__ __volatile__(
|
|
"sahf\n\t" /* clear flags (%eax = 0x0005) */
|
|
"div %b2\n\t" /* divide 5 by 2 */
|
|
"lahf" /* store flags into %ah */
|
|
: "=a" (test)
|
|
: "0" (5), "q" (2)
|
|
: "cc");
|
|
|
|
/* AH is 0x02 on Cyrix after the divide.. */
|
|
return (unsigned char) (test >> 8) == 0x02;
|
|
}
|
|
|
|
static void __cpuinit cyrix_identify(struct cpuinfo_x86 *c)
|
|
{
|
|
/* Detect Cyrix with disabled CPUID */
|
|
if (c->x86 == 4 && test_cyrix_52div()) {
|
|
unsigned char dir0, dir1;
|
|
|
|
strcpy(c->x86_vendor_id, "CyrixInstead");
|
|
c->x86_vendor = X86_VENDOR_CYRIX;
|
|
|
|
/* Actually enable cpuid on the older cyrix */
|
|
|
|
/* Retrieve CPU revisions */
|
|
|
|
do_cyrix_devid(&dir0, &dir1);
|
|
|
|
dir0 >>= 4;
|
|
|
|
/* Check it is an affected model */
|
|
|
|
if (dir0 == 5 || dir0 == 3) {
|
|
unsigned char ccr3;
|
|
unsigned long flags;
|
|
printk(KERN_INFO "Enabling CPUID on Cyrix processor.\n");
|
|
local_irq_save(flags);
|
|
ccr3 = getCx86(CX86_CCR3);
|
|
/* enable MAPEN */
|
|
setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10);
|
|
/* enable cpuid */
|
|
setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);
|
|
/* disable MAPEN */
|
|
setCx86(CX86_CCR3, ccr3);
|
|
local_irq_restore(flags);
|
|
}
|
|
}
|
|
}
|
|
|
|
static const struct cpu_dev __cpuinitconst cyrix_cpu_dev = {
|
|
.c_vendor = "Cyrix",
|
|
.c_ident = { "CyrixInstead" },
|
|
.c_early_init = early_init_cyrix,
|
|
.c_init = init_cyrix,
|
|
.c_identify = cyrix_identify,
|
|
.c_x86_vendor = X86_VENDOR_CYRIX,
|
|
};
|
|
|
|
cpu_dev_register(cyrix_cpu_dev);
|
|
|
|
static const struct cpu_dev __cpuinitconst nsc_cpu_dev = {
|
|
.c_vendor = "NSC",
|
|
.c_ident = { "Geode by NSC" },
|
|
.c_init = init_nsc,
|
|
.c_x86_vendor = X86_VENDOR_NSC,
|
|
};
|
|
|
|
cpu_dev_register(nsc_cpu_dev);
|