5208 lines
127 KiB
C
5208 lines
127 KiB
C
/*
|
|
* Copyright (c) 2005-2011 Atheros Communications Inc.
|
|
* Copyright (c) 2011-2013 Qualcomm Atheros, Inc.
|
|
*
|
|
* Permission to use, copy, modify, and/or distribute this software for any
|
|
* purpose with or without fee is hereby granted, provided that the above
|
|
* copyright notice and this permission notice appear in all copies.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
|
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
|
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
|
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
|
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
|
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
|
*/
|
|
|
|
#include "mac.h"
|
|
|
|
#include <net/mac80211.h>
|
|
#include <linux/etherdevice.h>
|
|
|
|
#include "hif.h"
|
|
#include "core.h"
|
|
#include "debug.h"
|
|
#include "wmi.h"
|
|
#include "htt.h"
|
|
#include "txrx.h"
|
|
#include "testmode.h"
|
|
#include "wmi.h"
|
|
#include "wmi-ops.h"
|
|
|
|
/**********/
|
|
/* Crypto */
|
|
/**********/
|
|
|
|
static int ath10k_send_key(struct ath10k_vif *arvif,
|
|
struct ieee80211_key_conf *key,
|
|
enum set_key_cmd cmd,
|
|
const u8 *macaddr)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
struct wmi_vdev_install_key_arg arg = {
|
|
.vdev_id = arvif->vdev_id,
|
|
.key_idx = key->keyidx,
|
|
.key_len = key->keylen,
|
|
.key_data = key->key,
|
|
.macaddr = macaddr,
|
|
};
|
|
|
|
lockdep_assert_held(&arvif->ar->conf_mutex);
|
|
|
|
if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE)
|
|
arg.key_flags = WMI_KEY_PAIRWISE;
|
|
else
|
|
arg.key_flags = WMI_KEY_GROUP;
|
|
|
|
switch (key->cipher) {
|
|
case WLAN_CIPHER_SUITE_CCMP:
|
|
arg.key_cipher = WMI_CIPHER_AES_CCM;
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_AP)
|
|
key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV_MGMT;
|
|
else
|
|
key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX;
|
|
break;
|
|
case WLAN_CIPHER_SUITE_TKIP:
|
|
arg.key_cipher = WMI_CIPHER_TKIP;
|
|
arg.key_txmic_len = 8;
|
|
arg.key_rxmic_len = 8;
|
|
break;
|
|
case WLAN_CIPHER_SUITE_WEP40:
|
|
case WLAN_CIPHER_SUITE_WEP104:
|
|
arg.key_cipher = WMI_CIPHER_WEP;
|
|
/* AP/IBSS mode requires self-key to be groupwise
|
|
* Otherwise pairwise key must be set */
|
|
if (memcmp(macaddr, arvif->vif->addr, ETH_ALEN))
|
|
arg.key_flags = WMI_KEY_PAIRWISE;
|
|
break;
|
|
default:
|
|
ath10k_warn(ar, "cipher %d is not supported\n", key->cipher);
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
if (cmd == DISABLE_KEY) {
|
|
arg.key_cipher = WMI_CIPHER_NONE;
|
|
arg.key_data = NULL;
|
|
}
|
|
|
|
return ath10k_wmi_vdev_install_key(arvif->ar, &arg);
|
|
}
|
|
|
|
static int ath10k_install_key(struct ath10k_vif *arvif,
|
|
struct ieee80211_key_conf *key,
|
|
enum set_key_cmd cmd,
|
|
const u8 *macaddr)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
reinit_completion(&ar->install_key_done);
|
|
|
|
ret = ath10k_send_key(arvif, key, cmd, macaddr);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = wait_for_completion_timeout(&ar->install_key_done, 3*HZ);
|
|
if (ret == 0)
|
|
return -ETIMEDOUT;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_install_peer_wep_keys(struct ath10k_vif *arvif,
|
|
const u8 *addr)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
struct ath10k_peer *peer;
|
|
int ret;
|
|
int i;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer = ath10k_peer_find(ar, arvif->vdev_id, addr);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (!peer)
|
|
return -ENOENT;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(arvif->wep_keys); i++) {
|
|
if (arvif->wep_keys[i] == NULL)
|
|
continue;
|
|
|
|
ret = ath10k_install_key(arvif, arvif->wep_keys[i], SET_KEY,
|
|
addr);
|
|
if (ret)
|
|
return ret;
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer->keys[i] = arvif->wep_keys[i];
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_clear_peer_keys(struct ath10k_vif *arvif,
|
|
const u8 *addr)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
struct ath10k_peer *peer;
|
|
int first_errno = 0;
|
|
int ret;
|
|
int i;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer = ath10k_peer_find(ar, arvif->vdev_id, addr);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (!peer)
|
|
return -ENOENT;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(peer->keys); i++) {
|
|
if (peer->keys[i] == NULL)
|
|
continue;
|
|
|
|
ret = ath10k_install_key(arvif, peer->keys[i],
|
|
DISABLE_KEY, addr);
|
|
if (ret && first_errno == 0)
|
|
first_errno = ret;
|
|
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to remove peer wep key %d: %d\n",
|
|
i, ret);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer->keys[i] = NULL;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
return first_errno;
|
|
}
|
|
|
|
bool ath10k_mac_is_peer_wep_key_set(struct ath10k *ar, const u8 *addr,
|
|
u8 keyidx)
|
|
{
|
|
struct ath10k_peer *peer;
|
|
int i;
|
|
|
|
lockdep_assert_held(&ar->data_lock);
|
|
|
|
/* We don't know which vdev this peer belongs to,
|
|
* since WMI doesn't give us that information.
|
|
*
|
|
* FIXME: multi-bss needs to be handled.
|
|
*/
|
|
peer = ath10k_peer_find(ar, 0, addr);
|
|
if (!peer)
|
|
return false;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(peer->keys); i++) {
|
|
if (peer->keys[i] && peer->keys[i]->keyidx == keyidx)
|
|
return true;
|
|
}
|
|
|
|
return false;
|
|
}
|
|
|
|
static int ath10k_clear_vdev_key(struct ath10k_vif *arvif,
|
|
struct ieee80211_key_conf *key)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
struct ath10k_peer *peer;
|
|
u8 addr[ETH_ALEN];
|
|
int first_errno = 0;
|
|
int ret;
|
|
int i;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
for (;;) {
|
|
/* since ath10k_install_key we can't hold data_lock all the
|
|
* time, so we try to remove the keys incrementally */
|
|
spin_lock_bh(&ar->data_lock);
|
|
i = 0;
|
|
list_for_each_entry(peer, &ar->peers, list) {
|
|
for (i = 0; i < ARRAY_SIZE(peer->keys); i++) {
|
|
if (peer->keys[i] == key) {
|
|
ether_addr_copy(addr, peer->addr);
|
|
peer->keys[i] = NULL;
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (i < ARRAY_SIZE(peer->keys))
|
|
break;
|
|
}
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (i == ARRAY_SIZE(peer->keys))
|
|
break;
|
|
|
|
ret = ath10k_install_key(arvif, key, DISABLE_KEY, addr);
|
|
if (ret && first_errno == 0)
|
|
first_errno = ret;
|
|
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to remove key for %pM: %d\n",
|
|
addr, ret);
|
|
}
|
|
|
|
return first_errno;
|
|
}
|
|
|
|
/*********************/
|
|
/* General utilities */
|
|
/*********************/
|
|
|
|
static inline enum wmi_phy_mode
|
|
chan_to_phymode(const struct cfg80211_chan_def *chandef)
|
|
{
|
|
enum wmi_phy_mode phymode = MODE_UNKNOWN;
|
|
|
|
switch (chandef->chan->band) {
|
|
case IEEE80211_BAND_2GHZ:
|
|
switch (chandef->width) {
|
|
case NL80211_CHAN_WIDTH_20_NOHT:
|
|
phymode = MODE_11G;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_20:
|
|
phymode = MODE_11NG_HT20;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_40:
|
|
phymode = MODE_11NG_HT40;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_5:
|
|
case NL80211_CHAN_WIDTH_10:
|
|
case NL80211_CHAN_WIDTH_80:
|
|
case NL80211_CHAN_WIDTH_80P80:
|
|
case NL80211_CHAN_WIDTH_160:
|
|
phymode = MODE_UNKNOWN;
|
|
break;
|
|
}
|
|
break;
|
|
case IEEE80211_BAND_5GHZ:
|
|
switch (chandef->width) {
|
|
case NL80211_CHAN_WIDTH_20_NOHT:
|
|
phymode = MODE_11A;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_20:
|
|
phymode = MODE_11NA_HT20;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_40:
|
|
phymode = MODE_11NA_HT40;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_80:
|
|
phymode = MODE_11AC_VHT80;
|
|
break;
|
|
case NL80211_CHAN_WIDTH_5:
|
|
case NL80211_CHAN_WIDTH_10:
|
|
case NL80211_CHAN_WIDTH_80P80:
|
|
case NL80211_CHAN_WIDTH_160:
|
|
phymode = MODE_UNKNOWN;
|
|
break;
|
|
}
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
WARN_ON(phymode == MODE_UNKNOWN);
|
|
return phymode;
|
|
}
|
|
|
|
static u8 ath10k_parse_mpdudensity(u8 mpdudensity)
|
|
{
|
|
/*
|
|
* 802.11n D2.0 defined values for "Minimum MPDU Start Spacing":
|
|
* 0 for no restriction
|
|
* 1 for 1/4 us
|
|
* 2 for 1/2 us
|
|
* 3 for 1 us
|
|
* 4 for 2 us
|
|
* 5 for 4 us
|
|
* 6 for 8 us
|
|
* 7 for 16 us
|
|
*/
|
|
switch (mpdudensity) {
|
|
case 0:
|
|
return 0;
|
|
case 1:
|
|
case 2:
|
|
case 3:
|
|
/* Our lower layer calculations limit our precision to
|
|
1 microsecond */
|
|
return 1;
|
|
case 4:
|
|
return 2;
|
|
case 5:
|
|
return 4;
|
|
case 6:
|
|
return 8;
|
|
case 7:
|
|
return 16;
|
|
default:
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
static int ath10k_peer_create(struct ath10k *ar, u32 vdev_id, const u8 *addr)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (ar->num_peers >= ar->max_num_peers)
|
|
return -ENOBUFS;
|
|
|
|
ret = ath10k_wmi_peer_create(ar, vdev_id, addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to create wmi peer %pM on vdev %i: %i\n",
|
|
addr, vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_wait_for_peer_created(ar, vdev_id, addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to wait for created wmi peer %pM on vdev %i: %i\n",
|
|
addr, vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ar->num_peers++;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_mac_set_kickout(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 param;
|
|
int ret;
|
|
|
|
param = ar->wmi.pdev_param->sta_kickout_th;
|
|
ret = ath10k_wmi_pdev_set_param(ar, param,
|
|
ATH10K_KICKOUT_THRESHOLD);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set kickout threshold on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
param = ar->wmi.vdev_param->ap_keepalive_min_idle_inactive_time_secs;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param,
|
|
ATH10K_KEEPALIVE_MIN_IDLE);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set keepalive minimum idle time on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
param = ar->wmi.vdev_param->ap_keepalive_max_idle_inactive_time_secs;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param,
|
|
ATH10K_KEEPALIVE_MAX_IDLE);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set keepalive maximum idle time on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
param = ar->wmi.vdev_param->ap_keepalive_max_unresponsive_time_secs;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param,
|
|
ATH10K_KEEPALIVE_MAX_UNRESPONSIVE);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set keepalive maximum unresponsive time on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_mac_set_rts(struct ath10k_vif *arvif, u32 value)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 vdev_param;
|
|
|
|
vdev_param = ar->wmi.vdev_param->rts_threshold;
|
|
return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, value);
|
|
}
|
|
|
|
static int ath10k_mac_set_frag(struct ath10k_vif *arvif, u32 value)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 vdev_param;
|
|
|
|
if (value != 0xFFFFFFFF)
|
|
value = clamp_t(u32, arvif->ar->hw->wiphy->frag_threshold,
|
|
ATH10K_FRAGMT_THRESHOLD_MIN,
|
|
ATH10K_FRAGMT_THRESHOLD_MAX);
|
|
|
|
vdev_param = ar->wmi.vdev_param->fragmentation_threshold;
|
|
return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, value);
|
|
}
|
|
|
|
static int ath10k_peer_delete(struct ath10k *ar, u32 vdev_id, const u8 *addr)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_wmi_peer_delete(ar, vdev_id, addr);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = ath10k_wait_for_peer_deleted(ar, vdev_id, addr);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ar->num_peers--;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ath10k_peer_cleanup(struct ath10k *ar, u32 vdev_id)
|
|
{
|
|
struct ath10k_peer *peer, *tmp;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
list_for_each_entry_safe(peer, tmp, &ar->peers, list) {
|
|
if (peer->vdev_id != vdev_id)
|
|
continue;
|
|
|
|
ath10k_warn(ar, "removing stale peer %pM from vdev_id %d\n",
|
|
peer->addr, vdev_id);
|
|
|
|
list_del(&peer->list);
|
|
kfree(peer);
|
|
ar->num_peers--;
|
|
}
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
static void ath10k_peer_cleanup_all(struct ath10k *ar)
|
|
{
|
|
struct ath10k_peer *peer, *tmp;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
list_for_each_entry_safe(peer, tmp, &ar->peers, list) {
|
|
list_del(&peer->list);
|
|
kfree(peer);
|
|
}
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
ar->num_peers = 0;
|
|
ar->num_stations = 0;
|
|
}
|
|
|
|
/************************/
|
|
/* Interface management */
|
|
/************************/
|
|
|
|
void ath10k_mac_vif_beacon_free(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
|
|
lockdep_assert_held(&ar->data_lock);
|
|
|
|
if (!arvif->beacon)
|
|
return;
|
|
|
|
if (!arvif->beacon_buf)
|
|
dma_unmap_single(ar->dev, ATH10K_SKB_CB(arvif->beacon)->paddr,
|
|
arvif->beacon->len, DMA_TO_DEVICE);
|
|
|
|
dev_kfree_skb_any(arvif->beacon);
|
|
|
|
arvif->beacon = NULL;
|
|
arvif->beacon_sent = false;
|
|
}
|
|
|
|
static void ath10k_mac_vif_beacon_cleanup(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
|
|
lockdep_assert_held(&ar->data_lock);
|
|
|
|
ath10k_mac_vif_beacon_free(arvif);
|
|
|
|
if (arvif->beacon_buf) {
|
|
dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN,
|
|
arvif->beacon_buf, arvif->beacon_paddr);
|
|
arvif->beacon_buf = NULL;
|
|
}
|
|
}
|
|
|
|
static inline int ath10k_vdev_setup_sync(struct ath10k *ar)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags))
|
|
return -ESHUTDOWN;
|
|
|
|
ret = wait_for_completion_timeout(&ar->vdev_setup_done,
|
|
ATH10K_VDEV_SETUP_TIMEOUT_HZ);
|
|
if (ret == 0)
|
|
return -ETIMEDOUT;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_monitor_vdev_start(struct ath10k *ar, int vdev_id)
|
|
{
|
|
struct cfg80211_chan_def *chandef = &ar->chandef;
|
|
struct ieee80211_channel *channel = chandef->chan;
|
|
struct wmi_vdev_start_request_arg arg = {};
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
arg.vdev_id = vdev_id;
|
|
arg.channel.freq = channel->center_freq;
|
|
arg.channel.band_center_freq1 = chandef->center_freq1;
|
|
|
|
/* TODO setup this dynamically, what in case we
|
|
don't have any vifs? */
|
|
arg.channel.mode = chan_to_phymode(chandef);
|
|
arg.channel.chan_radar =
|
|
!!(channel->flags & IEEE80211_CHAN_RADAR);
|
|
|
|
arg.channel.min_power = 0;
|
|
arg.channel.max_power = channel->max_power * 2;
|
|
arg.channel.max_reg_power = channel->max_reg_power * 2;
|
|
arg.channel.max_antenna_gain = channel->max_antenna_gain * 2;
|
|
|
|
reinit_completion(&ar->vdev_setup_done);
|
|
|
|
ret = ath10k_wmi_vdev_start(ar, &arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to request monitor vdev %i start: %d\n",
|
|
vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_vdev_setup_sync(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to synchronize setup for monitor vdev %i: %d\n",
|
|
vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_wmi_vdev_up(ar, vdev_id, 0, ar->mac_addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to put up monitor vdev %i: %d\n",
|
|
vdev_id, ret);
|
|
goto vdev_stop;
|
|
}
|
|
|
|
ar->monitor_vdev_id = vdev_id;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %i started\n",
|
|
ar->monitor_vdev_id);
|
|
return 0;
|
|
|
|
vdev_stop:
|
|
ret = ath10k_wmi_vdev_stop(ar, ar->monitor_vdev_id);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to stop monitor vdev %i after start failure: %d\n",
|
|
ar->monitor_vdev_id, ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_monitor_vdev_stop(struct ath10k *ar)
|
|
{
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_wmi_vdev_down(ar, ar->monitor_vdev_id);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to put down monitor vdev %i: %d\n",
|
|
ar->monitor_vdev_id, ret);
|
|
|
|
reinit_completion(&ar->vdev_setup_done);
|
|
|
|
ret = ath10k_wmi_vdev_stop(ar, ar->monitor_vdev_id);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to to request monitor vdev %i stop: %d\n",
|
|
ar->monitor_vdev_id, ret);
|
|
|
|
ret = ath10k_vdev_setup_sync(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to synchronise monitor vdev %i: %d\n",
|
|
ar->monitor_vdev_id, ret);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %i stopped\n",
|
|
ar->monitor_vdev_id);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_monitor_vdev_create(struct ath10k *ar)
|
|
{
|
|
int bit, ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (ar->free_vdev_map == 0) {
|
|
ath10k_warn(ar, "failed to find free vdev id for monitor vdev\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
bit = __ffs64(ar->free_vdev_map);
|
|
|
|
ar->monitor_vdev_id = bit;
|
|
|
|
ret = ath10k_wmi_vdev_create(ar, ar->monitor_vdev_id,
|
|
WMI_VDEV_TYPE_MONITOR,
|
|
0, ar->mac_addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to request monitor vdev %i creation: %d\n",
|
|
ar->monitor_vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ar->free_vdev_map &= ~(1LL << ar->monitor_vdev_id);
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %d created\n",
|
|
ar->monitor_vdev_id);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_monitor_vdev_delete(struct ath10k *ar)
|
|
{
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_wmi_vdev_delete(ar, ar->monitor_vdev_id);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to request wmi monitor vdev %i removal: %d\n",
|
|
ar->monitor_vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ar->free_vdev_map |= 1LL << ar->monitor_vdev_id;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %d deleted\n",
|
|
ar->monitor_vdev_id);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_monitor_start(struct ath10k *ar)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_monitor_vdev_create(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to create monitor vdev: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_monitor_vdev_start(ar, ar->monitor_vdev_id);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to start monitor vdev: %d\n", ret);
|
|
ath10k_monitor_vdev_delete(ar);
|
|
return ret;
|
|
}
|
|
|
|
ar->monitor_started = true;
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor started\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_monitor_stop(struct ath10k *ar)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_monitor_vdev_stop(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to stop monitor vdev: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_monitor_vdev_delete(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to delete monitor vdev: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ar->monitor_started = false;
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor stopped\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_monitor_recalc(struct ath10k *ar)
|
|
{
|
|
bool should_start;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
should_start = ar->monitor ||
|
|
ar->filter_flags & FIF_PROMISC_IN_BSS ||
|
|
test_bit(ATH10K_CAC_RUNNING, &ar->dev_flags);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac monitor recalc started? %d should? %d\n",
|
|
ar->monitor_started, should_start);
|
|
|
|
if (should_start == ar->monitor_started)
|
|
return 0;
|
|
|
|
if (should_start)
|
|
return ath10k_monitor_start(ar);
|
|
|
|
return ath10k_monitor_stop(ar);
|
|
}
|
|
|
|
static int ath10k_recalc_rtscts_prot(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 vdev_param, rts_cts = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
vdev_param = ar->wmi.vdev_param->enable_rtscts;
|
|
|
|
if (arvif->use_cts_prot || arvif->num_legacy_stations > 0)
|
|
rts_cts |= SM(WMI_RTSCTS_ENABLED, WMI_RTSCTS_SET);
|
|
|
|
if (arvif->num_legacy_stations > 0)
|
|
rts_cts |= SM(WMI_RTSCTS_ACROSS_SW_RETRIES,
|
|
WMI_RTSCTS_PROFILE);
|
|
|
|
return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
rts_cts);
|
|
}
|
|
|
|
static int ath10k_start_cac(struct ath10k *ar)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
set_bit(ATH10K_CAC_RUNNING, &ar->dev_flags);
|
|
|
|
ret = ath10k_monitor_recalc(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to start monitor (cac): %d\n", ret);
|
|
clear_bit(ATH10K_CAC_RUNNING, &ar->dev_flags);
|
|
return ret;
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac cac start monitor vdev %d\n",
|
|
ar->monitor_vdev_id);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_stop_cac(struct ath10k *ar)
|
|
{
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
/* CAC is not running - do nothing */
|
|
if (!test_bit(ATH10K_CAC_RUNNING, &ar->dev_flags))
|
|
return 0;
|
|
|
|
clear_bit(ATH10K_CAC_RUNNING, &ar->dev_flags);
|
|
ath10k_monitor_stop(ar);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac cac finished\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ath10k_recalc_radar_detection(struct ath10k *ar)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ath10k_stop_cac(ar);
|
|
|
|
if (!ar->radar_enabled)
|
|
return;
|
|
|
|
if (ar->num_started_vdevs > 0)
|
|
return;
|
|
|
|
ret = ath10k_start_cac(ar);
|
|
if (ret) {
|
|
/*
|
|
* Not possible to start CAC on current channel so starting
|
|
* radiation is not allowed, make this channel DFS_UNAVAILABLE
|
|
* by indicating that radar was detected.
|
|
*/
|
|
ath10k_warn(ar, "failed to start CAC: %d\n", ret);
|
|
ieee80211_radar_detected(ar->hw);
|
|
}
|
|
}
|
|
|
|
static int ath10k_vdev_start_restart(struct ath10k_vif *arvif, bool restart)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
struct cfg80211_chan_def *chandef = &ar->chandef;
|
|
struct wmi_vdev_start_request_arg arg = {};
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
reinit_completion(&ar->vdev_setup_done);
|
|
|
|
arg.vdev_id = arvif->vdev_id;
|
|
arg.dtim_period = arvif->dtim_period;
|
|
arg.bcn_intval = arvif->beacon_interval;
|
|
|
|
arg.channel.freq = chandef->chan->center_freq;
|
|
arg.channel.band_center_freq1 = chandef->center_freq1;
|
|
arg.channel.mode = chan_to_phymode(chandef);
|
|
|
|
arg.channel.min_power = 0;
|
|
arg.channel.max_power = chandef->chan->max_power * 2;
|
|
arg.channel.max_reg_power = chandef->chan->max_reg_power * 2;
|
|
arg.channel.max_antenna_gain = chandef->chan->max_antenna_gain * 2;
|
|
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
|
|
arg.ssid = arvif->u.ap.ssid;
|
|
arg.ssid_len = arvif->u.ap.ssid_len;
|
|
arg.hidden_ssid = arvif->u.ap.hidden_ssid;
|
|
|
|
/* For now allow DFS for AP mode */
|
|
arg.channel.chan_radar =
|
|
!!(chandef->chan->flags & IEEE80211_CHAN_RADAR);
|
|
} else if (arvif->vdev_type == WMI_VDEV_TYPE_IBSS) {
|
|
arg.ssid = arvif->vif->bss_conf.ssid;
|
|
arg.ssid_len = arvif->vif->bss_conf.ssid_len;
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d start center_freq %d phymode %s\n",
|
|
arg.vdev_id, arg.channel.freq,
|
|
ath10k_wmi_phymode_str(arg.channel.mode));
|
|
|
|
if (restart)
|
|
ret = ath10k_wmi_vdev_restart(ar, &arg);
|
|
else
|
|
ret = ath10k_wmi_vdev_start(ar, &arg);
|
|
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to start WMI vdev %i: %d\n",
|
|
arg.vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_vdev_setup_sync(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to synchronise setup for vdev %i: %d\n",
|
|
arg.vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ar->num_started_vdevs++;
|
|
ath10k_recalc_radar_detection(ar);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_vdev_start(struct ath10k_vif *arvif)
|
|
{
|
|
return ath10k_vdev_start_restart(arvif, false);
|
|
}
|
|
|
|
static int ath10k_vdev_restart(struct ath10k_vif *arvif)
|
|
{
|
|
return ath10k_vdev_start_restart(arvif, true);
|
|
}
|
|
|
|
static int ath10k_vdev_stop(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
reinit_completion(&ar->vdev_setup_done);
|
|
|
|
ret = ath10k_wmi_vdev_stop(ar, arvif->vdev_id);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to stop WMI vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_vdev_setup_sync(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to syncronise setup for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
WARN_ON(ar->num_started_vdevs == 0);
|
|
|
|
if (ar->num_started_vdevs != 0) {
|
|
ar->num_started_vdevs--;
|
|
ath10k_recalc_radar_detection(ar);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_control_beaconing(struct ath10k_vif *arvif,
|
|
struct ieee80211_bss_conf *info)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&arvif->ar->conf_mutex);
|
|
|
|
if (!info->enable_beacon) {
|
|
ath10k_vdev_stop(arvif);
|
|
|
|
arvif->is_started = false;
|
|
arvif->is_up = false;
|
|
|
|
spin_lock_bh(&arvif->ar->data_lock);
|
|
ath10k_mac_vif_beacon_free(arvif);
|
|
spin_unlock_bh(&arvif->ar->data_lock);
|
|
|
|
return;
|
|
}
|
|
|
|
arvif->tx_seq_no = 0x1000;
|
|
|
|
ret = ath10k_vdev_start(arvif);
|
|
if (ret)
|
|
return;
|
|
|
|
arvif->aid = 0;
|
|
ether_addr_copy(arvif->bssid, info->bssid);
|
|
|
|
ret = ath10k_wmi_vdev_up(arvif->ar, arvif->vdev_id, arvif->aid,
|
|
arvif->bssid);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to bring up vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
ath10k_vdev_stop(arvif);
|
|
return;
|
|
}
|
|
|
|
arvif->is_started = true;
|
|
arvif->is_up = true;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d up\n", arvif->vdev_id);
|
|
}
|
|
|
|
static void ath10k_control_ibss(struct ath10k_vif *arvif,
|
|
struct ieee80211_bss_conf *info,
|
|
const u8 self_peer[ETH_ALEN])
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 vdev_param;
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&arvif->ar->conf_mutex);
|
|
|
|
if (!info->ibss_joined) {
|
|
ret = ath10k_peer_delete(arvif->ar, arvif->vdev_id, self_peer);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to delete IBSS self peer %pM for vdev %d: %d\n",
|
|
self_peer, arvif->vdev_id, ret);
|
|
|
|
if (is_zero_ether_addr(arvif->bssid))
|
|
return;
|
|
|
|
memset(arvif->bssid, 0, ETH_ALEN);
|
|
|
|
return;
|
|
}
|
|
|
|
ret = ath10k_peer_create(arvif->ar, arvif->vdev_id, self_peer);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to create IBSS self peer %pM for vdev %d: %d\n",
|
|
self_peer, arvif->vdev_id, ret);
|
|
return;
|
|
}
|
|
|
|
vdev_param = arvif->ar->wmi.vdev_param->atim_window;
|
|
ret = ath10k_wmi_vdev_set_param(arvif->ar, arvif->vdev_id, vdev_param,
|
|
ATH10K_DEFAULT_ATIM);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set IBSS ATIM for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
static int ath10k_mac_vif_recalc_ps_wake_threshold(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 param;
|
|
u32 value;
|
|
int ret;
|
|
|
|
lockdep_assert_held(&arvif->ar->conf_mutex);
|
|
|
|
if (arvif->u.sta.uapsd)
|
|
value = WMI_STA_PS_TX_WAKE_THRESHOLD_NEVER;
|
|
else
|
|
value = WMI_STA_PS_TX_WAKE_THRESHOLD_ALWAYS;
|
|
|
|
param = WMI_STA_PS_PARAM_TX_WAKE_THRESHOLD;
|
|
ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, param, value);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to submit ps wake threshold %u on vdev %i: %d\n",
|
|
value, arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_mac_vif_recalc_ps_poll_count(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 param;
|
|
u32 value;
|
|
int ret;
|
|
|
|
lockdep_assert_held(&arvif->ar->conf_mutex);
|
|
|
|
if (arvif->u.sta.uapsd)
|
|
value = WMI_STA_PS_PSPOLL_COUNT_UAPSD;
|
|
else
|
|
value = WMI_STA_PS_PSPOLL_COUNT_NO_MAX;
|
|
|
|
param = WMI_STA_PS_PARAM_PSPOLL_COUNT;
|
|
ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id,
|
|
param, value);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to submit ps poll count %u on vdev %i: %d\n",
|
|
value, arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_mac_vif_setup_ps(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
struct ieee80211_vif *vif = arvif->vif;
|
|
struct ieee80211_conf *conf = &ar->hw->conf;
|
|
enum wmi_sta_powersave_param param;
|
|
enum wmi_sta_ps_mode psmode;
|
|
int ret;
|
|
int ps_timeout;
|
|
|
|
lockdep_assert_held(&arvif->ar->conf_mutex);
|
|
|
|
if (arvif->vif->type != NL80211_IFTYPE_STATION)
|
|
return 0;
|
|
|
|
if (vif->bss_conf.ps) {
|
|
psmode = WMI_STA_PS_MODE_ENABLED;
|
|
param = WMI_STA_PS_PARAM_INACTIVITY_TIME;
|
|
|
|
ps_timeout = conf->dynamic_ps_timeout;
|
|
if (ps_timeout == 0) {
|
|
/* Firmware doesn't like 0 */
|
|
ps_timeout = ieee80211_tu_to_usec(
|
|
vif->bss_conf.beacon_int) / 1000;
|
|
}
|
|
|
|
ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, param,
|
|
ps_timeout);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set inactivity time for vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
} else {
|
|
psmode = WMI_STA_PS_MODE_DISABLED;
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d psmode %s\n",
|
|
arvif->vdev_id, psmode ? "enable" : "disable");
|
|
|
|
ret = ath10k_wmi_set_psmode(ar, arvif->vdev_id, psmode);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set PS Mode %d for vdev %d: %d\n",
|
|
psmode, arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**********************/
|
|
/* Station management */
|
|
/**********************/
|
|
|
|
static u32 ath10k_peer_assoc_h_listen_intval(struct ath10k *ar,
|
|
struct ieee80211_vif *vif)
|
|
{
|
|
/* Some firmware revisions have unstable STA powersave when listen
|
|
* interval is set too high (e.g. 5). The symptoms are firmware doesn't
|
|
* generate NullFunc frames properly even if buffered frames have been
|
|
* indicated in Beacon TIM. Firmware would seldom wake up to pull
|
|
* buffered frames. Often pinging the device from AP would simply fail.
|
|
*
|
|
* As a workaround set it to 1.
|
|
*/
|
|
if (vif->type == NL80211_IFTYPE_STATION)
|
|
return 1;
|
|
|
|
return ar->hw->conf.listen_interval;
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_basic(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ether_addr_copy(arg->addr, sta->addr);
|
|
arg->vdev_id = arvif->vdev_id;
|
|
arg->peer_aid = sta->aid;
|
|
arg->peer_flags |= WMI_PEER_AUTH;
|
|
arg->peer_listen_intval = ath10k_peer_assoc_h_listen_intval(ar, vif);
|
|
arg->peer_num_spatial_streams = 1;
|
|
arg->peer_caps = vif->bss_conf.assoc_capability;
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_crypto(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
struct ieee80211_bss_conf *info = &vif->bss_conf;
|
|
struct cfg80211_bss *bss;
|
|
const u8 *rsnie = NULL;
|
|
const u8 *wpaie = NULL;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
bss = cfg80211_get_bss(ar->hw->wiphy, ar->hw->conf.chandef.chan,
|
|
info->bssid, NULL, 0, 0, 0);
|
|
if (bss) {
|
|
const struct cfg80211_bss_ies *ies;
|
|
|
|
rcu_read_lock();
|
|
rsnie = ieee80211_bss_get_ie(bss, WLAN_EID_RSN);
|
|
|
|
ies = rcu_dereference(bss->ies);
|
|
|
|
wpaie = cfg80211_find_vendor_ie(WLAN_OUI_MICROSOFT,
|
|
WLAN_OUI_TYPE_MICROSOFT_WPA,
|
|
ies->data,
|
|
ies->len);
|
|
rcu_read_unlock();
|
|
cfg80211_put_bss(ar->hw->wiphy, bss);
|
|
}
|
|
|
|
/* FIXME: base on RSN IE/WPA IE is a correct idea? */
|
|
if (rsnie || wpaie) {
|
|
ath10k_dbg(ar, ATH10K_DBG_WMI, "%s: rsn ie found\n", __func__);
|
|
arg->peer_flags |= WMI_PEER_NEED_PTK_4_WAY;
|
|
}
|
|
|
|
if (wpaie) {
|
|
ath10k_dbg(ar, ATH10K_DBG_WMI, "%s: wpa ie found\n", __func__);
|
|
arg->peer_flags |= WMI_PEER_NEED_GTK_2_WAY;
|
|
}
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_rates(struct ath10k *ar,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
struct wmi_rate_set_arg *rateset = &arg->peer_legacy_rates;
|
|
const struct ieee80211_supported_band *sband;
|
|
const struct ieee80211_rate *rates;
|
|
u32 ratemask;
|
|
int i;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
sband = ar->hw->wiphy->bands[ar->hw->conf.chandef.chan->band];
|
|
ratemask = sta->supp_rates[ar->hw->conf.chandef.chan->band];
|
|
rates = sband->bitrates;
|
|
|
|
rateset->num_rates = 0;
|
|
|
|
for (i = 0; i < 32; i++, ratemask >>= 1, rates++) {
|
|
if (!(ratemask & 1))
|
|
continue;
|
|
|
|
rateset->rates[rateset->num_rates] = rates->hw_value;
|
|
rateset->num_rates++;
|
|
}
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_ht(struct ath10k *ar,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
const struct ieee80211_sta_ht_cap *ht_cap = &sta->ht_cap;
|
|
int i, n;
|
|
u32 stbc;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (!ht_cap->ht_supported)
|
|
return;
|
|
|
|
arg->peer_flags |= WMI_PEER_HT;
|
|
arg->peer_max_mpdu = (1 << (IEEE80211_HT_MAX_AMPDU_FACTOR +
|
|
ht_cap->ampdu_factor)) - 1;
|
|
|
|
arg->peer_mpdu_density =
|
|
ath10k_parse_mpdudensity(ht_cap->ampdu_density);
|
|
|
|
arg->peer_ht_caps = ht_cap->cap;
|
|
arg->peer_rate_caps |= WMI_RC_HT_FLAG;
|
|
|
|
if (ht_cap->cap & IEEE80211_HT_CAP_LDPC_CODING)
|
|
arg->peer_flags |= WMI_PEER_LDPC;
|
|
|
|
if (sta->bandwidth >= IEEE80211_STA_RX_BW_40) {
|
|
arg->peer_flags |= WMI_PEER_40MHZ;
|
|
arg->peer_rate_caps |= WMI_RC_CW40_FLAG;
|
|
}
|
|
|
|
if (ht_cap->cap & IEEE80211_HT_CAP_SGI_20)
|
|
arg->peer_rate_caps |= WMI_RC_SGI_FLAG;
|
|
|
|
if (ht_cap->cap & IEEE80211_HT_CAP_SGI_40)
|
|
arg->peer_rate_caps |= WMI_RC_SGI_FLAG;
|
|
|
|
if (ht_cap->cap & IEEE80211_HT_CAP_TX_STBC) {
|
|
arg->peer_rate_caps |= WMI_RC_TX_STBC_FLAG;
|
|
arg->peer_flags |= WMI_PEER_STBC;
|
|
}
|
|
|
|
if (ht_cap->cap & IEEE80211_HT_CAP_RX_STBC) {
|
|
stbc = ht_cap->cap & IEEE80211_HT_CAP_RX_STBC;
|
|
stbc = stbc >> IEEE80211_HT_CAP_RX_STBC_SHIFT;
|
|
stbc = stbc << WMI_RC_RX_STBC_FLAG_S;
|
|
arg->peer_rate_caps |= stbc;
|
|
arg->peer_flags |= WMI_PEER_STBC;
|
|
}
|
|
|
|
if (ht_cap->mcs.rx_mask[1] && ht_cap->mcs.rx_mask[2])
|
|
arg->peer_rate_caps |= WMI_RC_TS_FLAG;
|
|
else if (ht_cap->mcs.rx_mask[1])
|
|
arg->peer_rate_caps |= WMI_RC_DS_FLAG;
|
|
|
|
for (i = 0, n = 0; i < IEEE80211_HT_MCS_MASK_LEN*8; i++)
|
|
if (ht_cap->mcs.rx_mask[i/8] & (1 << i%8))
|
|
arg->peer_ht_rates.rates[n++] = i;
|
|
|
|
/*
|
|
* This is a workaround for HT-enabled STAs which break the spec
|
|
* and have no HT capabilities RX mask (no HT RX MCS map).
|
|
*
|
|
* As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
|
|
* MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
|
|
*
|
|
* Firmware asserts if such situation occurs.
|
|
*/
|
|
if (n == 0) {
|
|
arg->peer_ht_rates.num_rates = 8;
|
|
for (i = 0; i < arg->peer_ht_rates.num_rates; i++)
|
|
arg->peer_ht_rates.rates[i] = i;
|
|
} else {
|
|
arg->peer_ht_rates.num_rates = n;
|
|
arg->peer_num_spatial_streams = sta->rx_nss;
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac ht peer %pM mcs cnt %d nss %d\n",
|
|
arg->addr,
|
|
arg->peer_ht_rates.num_rates,
|
|
arg->peer_num_spatial_streams);
|
|
}
|
|
|
|
static int ath10k_peer_assoc_qos_ap(struct ath10k *ar,
|
|
struct ath10k_vif *arvif,
|
|
struct ieee80211_sta *sta)
|
|
{
|
|
u32 uapsd = 0;
|
|
u32 max_sp = 0;
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (sta->wme && sta->uapsd_queues) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac uapsd_queues 0x%x max_sp %d\n",
|
|
sta->uapsd_queues, sta->max_sp);
|
|
|
|
if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_VO)
|
|
uapsd |= WMI_AP_PS_UAPSD_AC3_DELIVERY_EN |
|
|
WMI_AP_PS_UAPSD_AC3_TRIGGER_EN;
|
|
if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_VI)
|
|
uapsd |= WMI_AP_PS_UAPSD_AC2_DELIVERY_EN |
|
|
WMI_AP_PS_UAPSD_AC2_TRIGGER_EN;
|
|
if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_BK)
|
|
uapsd |= WMI_AP_PS_UAPSD_AC1_DELIVERY_EN |
|
|
WMI_AP_PS_UAPSD_AC1_TRIGGER_EN;
|
|
if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_BE)
|
|
uapsd |= WMI_AP_PS_UAPSD_AC0_DELIVERY_EN |
|
|
WMI_AP_PS_UAPSD_AC0_TRIGGER_EN;
|
|
|
|
if (sta->max_sp < MAX_WMI_AP_PS_PEER_PARAM_MAX_SP)
|
|
max_sp = sta->max_sp;
|
|
|
|
ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id,
|
|
sta->addr,
|
|
WMI_AP_PS_PEER_PARAM_UAPSD,
|
|
uapsd);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set ap ps peer param uapsd for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id,
|
|
sta->addr,
|
|
WMI_AP_PS_PEER_PARAM_MAX_SP,
|
|
max_sp);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set ap ps peer param max sp for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
/* TODO setup this based on STA listen interval and
|
|
beacon interval. Currently we don't know
|
|
sta->listen_interval - mac80211 patch required.
|
|
Currently use 10 seconds */
|
|
ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id, sta->addr,
|
|
WMI_AP_PS_PEER_PARAM_AGEOUT_TIME,
|
|
10);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set ap ps peer param ageout time for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
const struct ieee80211_sta_vht_cap *vht_cap = &sta->vht_cap;
|
|
u8 ampdu_factor;
|
|
|
|
if (!vht_cap->vht_supported)
|
|
return;
|
|
|
|
arg->peer_flags |= WMI_PEER_VHT;
|
|
arg->peer_vht_caps = vht_cap->cap;
|
|
|
|
ampdu_factor = (vht_cap->cap &
|
|
IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK) >>
|
|
IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT;
|
|
|
|
/* Workaround: Some Netgear/Linksys 11ac APs set Rx A-MPDU factor to
|
|
* zero in VHT IE. Using it would result in degraded throughput.
|
|
* arg->peer_max_mpdu at this point contains HT max_mpdu so keep
|
|
* it if VHT max_mpdu is smaller. */
|
|
arg->peer_max_mpdu = max(arg->peer_max_mpdu,
|
|
(1U << (IEEE80211_HT_MAX_AMPDU_FACTOR +
|
|
ampdu_factor)) - 1);
|
|
|
|
if (sta->bandwidth == IEEE80211_STA_RX_BW_80)
|
|
arg->peer_flags |= WMI_PEER_80MHZ;
|
|
|
|
arg->peer_vht_rates.rx_max_rate =
|
|
__le16_to_cpu(vht_cap->vht_mcs.rx_highest);
|
|
arg->peer_vht_rates.rx_mcs_set =
|
|
__le16_to_cpu(vht_cap->vht_mcs.rx_mcs_map);
|
|
arg->peer_vht_rates.tx_max_rate =
|
|
__le16_to_cpu(vht_cap->vht_mcs.tx_highest);
|
|
arg->peer_vht_rates.tx_mcs_set =
|
|
__le16_to_cpu(vht_cap->vht_mcs.tx_mcs_map);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x\n",
|
|
sta->addr, arg->peer_max_mpdu, arg->peer_flags);
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_qos(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
|
|
switch (arvif->vdev_type) {
|
|
case WMI_VDEV_TYPE_AP:
|
|
if (sta->wme)
|
|
arg->peer_flags |= WMI_PEER_QOS;
|
|
|
|
if (sta->wme && sta->uapsd_queues) {
|
|
arg->peer_flags |= WMI_PEER_APSD;
|
|
arg->peer_rate_caps |= WMI_RC_UAPSD_FLAG;
|
|
}
|
|
break;
|
|
case WMI_VDEV_TYPE_STA:
|
|
if (vif->bss_conf.qos)
|
|
arg->peer_flags |= WMI_PEER_QOS;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static bool ath10k_mac_sta_has_11g_rates(struct ieee80211_sta *sta)
|
|
{
|
|
/* First 4 rates in ath10k_rates are CCK (11b) rates. */
|
|
return sta->supp_rates[IEEE80211_BAND_2GHZ] >> 4;
|
|
}
|
|
|
|
static void ath10k_peer_assoc_h_phymode(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
enum wmi_phy_mode phymode = MODE_UNKNOWN;
|
|
|
|
switch (ar->hw->conf.chandef.chan->band) {
|
|
case IEEE80211_BAND_2GHZ:
|
|
if (sta->ht_cap.ht_supported) {
|
|
if (sta->bandwidth == IEEE80211_STA_RX_BW_40)
|
|
phymode = MODE_11NG_HT40;
|
|
else
|
|
phymode = MODE_11NG_HT20;
|
|
} else if (ath10k_mac_sta_has_11g_rates(sta)) {
|
|
phymode = MODE_11G;
|
|
} else {
|
|
phymode = MODE_11B;
|
|
}
|
|
|
|
break;
|
|
case IEEE80211_BAND_5GHZ:
|
|
/*
|
|
* Check VHT first.
|
|
*/
|
|
if (sta->vht_cap.vht_supported) {
|
|
if (sta->bandwidth == IEEE80211_STA_RX_BW_80)
|
|
phymode = MODE_11AC_VHT80;
|
|
else if (sta->bandwidth == IEEE80211_STA_RX_BW_40)
|
|
phymode = MODE_11AC_VHT40;
|
|
else if (sta->bandwidth == IEEE80211_STA_RX_BW_20)
|
|
phymode = MODE_11AC_VHT20;
|
|
} else if (sta->ht_cap.ht_supported) {
|
|
if (sta->bandwidth == IEEE80211_STA_RX_BW_40)
|
|
phymode = MODE_11NA_HT40;
|
|
else
|
|
phymode = MODE_11NA_HT20;
|
|
} else {
|
|
phymode = MODE_11A;
|
|
}
|
|
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac peer %pM phymode %s\n",
|
|
sta->addr, ath10k_wmi_phymode_str(phymode));
|
|
|
|
arg->peer_phymode = phymode;
|
|
WARN_ON(phymode == MODE_UNKNOWN);
|
|
}
|
|
|
|
static int ath10k_peer_assoc_prepare(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
struct wmi_peer_assoc_complete_arg *arg)
|
|
{
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
memset(arg, 0, sizeof(*arg));
|
|
|
|
ath10k_peer_assoc_h_basic(ar, vif, sta, arg);
|
|
ath10k_peer_assoc_h_crypto(ar, vif, arg);
|
|
ath10k_peer_assoc_h_rates(ar, sta, arg);
|
|
ath10k_peer_assoc_h_ht(ar, sta, arg);
|
|
ath10k_peer_assoc_h_vht(ar, sta, arg);
|
|
ath10k_peer_assoc_h_qos(ar, vif, sta, arg);
|
|
ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const u32 ath10k_smps_map[] = {
|
|
[WLAN_HT_CAP_SM_PS_STATIC] = WMI_PEER_SMPS_STATIC,
|
|
[WLAN_HT_CAP_SM_PS_DYNAMIC] = WMI_PEER_SMPS_DYNAMIC,
|
|
[WLAN_HT_CAP_SM_PS_INVALID] = WMI_PEER_SMPS_PS_NONE,
|
|
[WLAN_HT_CAP_SM_PS_DISABLED] = WMI_PEER_SMPS_PS_NONE,
|
|
};
|
|
|
|
static int ath10k_setup_peer_smps(struct ath10k *ar, struct ath10k_vif *arvif,
|
|
const u8 *addr,
|
|
const struct ieee80211_sta_ht_cap *ht_cap)
|
|
{
|
|
int smps;
|
|
|
|
if (!ht_cap->ht_supported)
|
|
return 0;
|
|
|
|
smps = ht_cap->cap & IEEE80211_HT_CAP_SM_PS;
|
|
smps >>= IEEE80211_HT_CAP_SM_PS_SHIFT;
|
|
|
|
if (smps >= ARRAY_SIZE(ath10k_smps_map))
|
|
return -EINVAL;
|
|
|
|
return ath10k_wmi_peer_set_param(ar, arvif->vdev_id, addr,
|
|
WMI_PEER_SMPS_STATE,
|
|
ath10k_smps_map[smps]);
|
|
}
|
|
|
|
/* can be called only in mac80211 callbacks due to `key_count` usage */
|
|
static void ath10k_bss_assoc(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_bss_conf *bss_conf)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct ieee80211_sta_ht_cap ht_cap;
|
|
struct wmi_peer_assoc_complete_arg peer_arg;
|
|
struct ieee80211_sta *ap_sta;
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %i assoc bssid %pM aid %d\n",
|
|
arvif->vdev_id, arvif->bssid, arvif->aid);
|
|
|
|
rcu_read_lock();
|
|
|
|
ap_sta = ieee80211_find_sta(vif, bss_conf->bssid);
|
|
if (!ap_sta) {
|
|
ath10k_warn(ar, "failed to find station entry for bss %pM vdev %i\n",
|
|
bss_conf->bssid, arvif->vdev_id);
|
|
rcu_read_unlock();
|
|
return;
|
|
}
|
|
|
|
/* ap_sta must be accessed only within rcu section which must be left
|
|
* before calling ath10k_setup_peer_smps() which might sleep. */
|
|
ht_cap = ap_sta->ht_cap;
|
|
|
|
ret = ath10k_peer_assoc_prepare(ar, vif, ap_sta, &peer_arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to prepare peer assoc for %pM vdev %i: %d\n",
|
|
bss_conf->bssid, arvif->vdev_id, ret);
|
|
rcu_read_unlock();
|
|
return;
|
|
}
|
|
|
|
rcu_read_unlock();
|
|
|
|
ret = ath10k_wmi_peer_assoc(ar, &peer_arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to run peer assoc for %pM vdev %i: %d\n",
|
|
bss_conf->bssid, arvif->vdev_id, ret);
|
|
return;
|
|
}
|
|
|
|
ret = ath10k_setup_peer_smps(ar, arvif, bss_conf->bssid, &ht_cap);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to setup peer SMPS for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return;
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d up (associated) bssid %pM aid %d\n",
|
|
arvif->vdev_id, bss_conf->bssid, bss_conf->aid);
|
|
|
|
WARN_ON(arvif->is_up);
|
|
|
|
arvif->aid = bss_conf->aid;
|
|
ether_addr_copy(arvif->bssid, bss_conf->bssid);
|
|
|
|
ret = ath10k_wmi_vdev_up(ar, arvif->vdev_id, arvif->aid, arvif->bssid);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set vdev %d up: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return;
|
|
}
|
|
|
|
arvif->is_up = true;
|
|
}
|
|
|
|
static void ath10k_bss_disassoc(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %i disassoc bssid %pM\n",
|
|
arvif->vdev_id, arvif->bssid);
|
|
|
|
ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id);
|
|
if (ret)
|
|
ath10k_warn(ar, "faield to down vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
|
|
arvif->def_wep_key_idx = 0;
|
|
arvif->is_up = false;
|
|
}
|
|
|
|
static int ath10k_station_assoc(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
bool reassoc)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct wmi_peer_assoc_complete_arg peer_arg;
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_peer_assoc_prepare(ar, vif, sta, &peer_arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to prepare WMI peer assoc for %pM vdev %i: %i\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
peer_arg.peer_reassoc = reassoc;
|
|
ret = ath10k_wmi_peer_assoc(ar, &peer_arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to run peer assoc for STA %pM vdev %i: %d\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
/* Re-assoc is run only to update supported rates for given station. It
|
|
* doesn't make much sense to reconfigure the peer completely.
|
|
*/
|
|
if (!reassoc) {
|
|
ret = ath10k_setup_peer_smps(ar, arvif, sta->addr,
|
|
&sta->ht_cap);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to setup peer SMPS for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_peer_assoc_qos_ap(ar, arvif, sta);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set qos params for STA %pM for vdev %i: %d\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
if (!sta->wme) {
|
|
arvif->num_legacy_stations++;
|
|
ret = ath10k_recalc_rtscts_prot(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalculate rts/cts prot for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
ret = ath10k_install_peer_wep_keys(arvif, sta->addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to install peer wep keys for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_station_disassoc(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (!sta->wme) {
|
|
arvif->num_legacy_stations--;
|
|
ret = ath10k_recalc_rtscts_prot(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalculate rts/cts prot for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
ret = ath10k_clear_peer_keys(arvif, sta->addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to clear all peer wep keys for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
/**************/
|
|
/* Regulatory */
|
|
/**************/
|
|
|
|
static int ath10k_update_channel_list(struct ath10k *ar)
|
|
{
|
|
struct ieee80211_hw *hw = ar->hw;
|
|
struct ieee80211_supported_band **bands;
|
|
enum ieee80211_band band;
|
|
struct ieee80211_channel *channel;
|
|
struct wmi_scan_chan_list_arg arg = {0};
|
|
struct wmi_channel_arg *ch;
|
|
bool passive;
|
|
int len;
|
|
int ret;
|
|
int i;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
bands = hw->wiphy->bands;
|
|
for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
|
|
if (!bands[band])
|
|
continue;
|
|
|
|
for (i = 0; i < bands[band]->n_channels; i++) {
|
|
if (bands[band]->channels[i].flags &
|
|
IEEE80211_CHAN_DISABLED)
|
|
continue;
|
|
|
|
arg.n_channels++;
|
|
}
|
|
}
|
|
|
|
len = sizeof(struct wmi_channel_arg) * arg.n_channels;
|
|
arg.channels = kzalloc(len, GFP_KERNEL);
|
|
if (!arg.channels)
|
|
return -ENOMEM;
|
|
|
|
ch = arg.channels;
|
|
for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
|
|
if (!bands[band])
|
|
continue;
|
|
|
|
for (i = 0; i < bands[band]->n_channels; i++) {
|
|
channel = &bands[band]->channels[i];
|
|
|
|
if (channel->flags & IEEE80211_CHAN_DISABLED)
|
|
continue;
|
|
|
|
ch->allow_ht = true;
|
|
|
|
/* FIXME: when should we really allow VHT? */
|
|
ch->allow_vht = true;
|
|
|
|
ch->allow_ibss =
|
|
!(channel->flags & IEEE80211_CHAN_NO_IR);
|
|
|
|
ch->ht40plus =
|
|
!(channel->flags & IEEE80211_CHAN_NO_HT40PLUS);
|
|
|
|
ch->chan_radar =
|
|
!!(channel->flags & IEEE80211_CHAN_RADAR);
|
|
|
|
passive = channel->flags & IEEE80211_CHAN_NO_IR;
|
|
ch->passive = passive;
|
|
|
|
ch->freq = channel->center_freq;
|
|
ch->band_center_freq1 = channel->center_freq;
|
|
ch->min_power = 0;
|
|
ch->max_power = channel->max_power * 2;
|
|
ch->max_reg_power = channel->max_reg_power * 2;
|
|
ch->max_antenna_gain = channel->max_antenna_gain * 2;
|
|
ch->reg_class_id = 0; /* FIXME */
|
|
|
|
/* FIXME: why use only legacy modes, why not any
|
|
* HT/VHT modes? Would that even make any
|
|
* difference? */
|
|
if (channel->band == IEEE80211_BAND_2GHZ)
|
|
ch->mode = MODE_11G;
|
|
else
|
|
ch->mode = MODE_11A;
|
|
|
|
if (WARN_ON_ONCE(ch->mode == MODE_UNKNOWN))
|
|
continue;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_WMI,
|
|
"mac channel [%zd/%d] freq %d maxpower %d regpower %d antenna %d mode %d\n",
|
|
ch - arg.channels, arg.n_channels,
|
|
ch->freq, ch->max_power, ch->max_reg_power,
|
|
ch->max_antenna_gain, ch->mode);
|
|
|
|
ch++;
|
|
}
|
|
}
|
|
|
|
ret = ath10k_wmi_scan_chan_list(ar, &arg);
|
|
kfree(arg.channels);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static enum wmi_dfs_region
|
|
ath10k_mac_get_dfs_region(enum nl80211_dfs_regions dfs_region)
|
|
{
|
|
switch (dfs_region) {
|
|
case NL80211_DFS_UNSET:
|
|
return WMI_UNINIT_DFS_DOMAIN;
|
|
case NL80211_DFS_FCC:
|
|
return WMI_FCC_DFS_DOMAIN;
|
|
case NL80211_DFS_ETSI:
|
|
return WMI_ETSI_DFS_DOMAIN;
|
|
case NL80211_DFS_JP:
|
|
return WMI_MKK4_DFS_DOMAIN;
|
|
}
|
|
return WMI_UNINIT_DFS_DOMAIN;
|
|
}
|
|
|
|
static void ath10k_regd_update(struct ath10k *ar)
|
|
{
|
|
struct reg_dmn_pair_mapping *regpair;
|
|
int ret;
|
|
enum wmi_dfs_region wmi_dfs_reg;
|
|
enum nl80211_dfs_regions nl_dfs_reg;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_update_channel_list(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to update channel list: %d\n", ret);
|
|
|
|
regpair = ar->ath_common.regulatory.regpair;
|
|
|
|
if (config_enabled(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector) {
|
|
nl_dfs_reg = ar->dfs_detector->region;
|
|
wmi_dfs_reg = ath10k_mac_get_dfs_region(nl_dfs_reg);
|
|
} else {
|
|
wmi_dfs_reg = WMI_UNINIT_DFS_DOMAIN;
|
|
}
|
|
|
|
/* Target allows setting up per-band regdomain but ath_common provides
|
|
* a combined one only */
|
|
ret = ath10k_wmi_pdev_set_regdomain(ar,
|
|
regpair->reg_domain,
|
|
regpair->reg_domain, /* 2ghz */
|
|
regpair->reg_domain, /* 5ghz */
|
|
regpair->reg_2ghz_ctl,
|
|
regpair->reg_5ghz_ctl,
|
|
wmi_dfs_reg);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set pdev regdomain: %d\n", ret);
|
|
}
|
|
|
|
static void ath10k_reg_notifier(struct wiphy *wiphy,
|
|
struct regulatory_request *request)
|
|
{
|
|
struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy);
|
|
struct ath10k *ar = hw->priv;
|
|
bool result;
|
|
|
|
ath_reg_notifier_apply(wiphy, request, &ar->ath_common.regulatory);
|
|
|
|
if (config_enabled(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector) {
|
|
ath10k_dbg(ar, ATH10K_DBG_REGULATORY, "dfs region 0x%x\n",
|
|
request->dfs_region);
|
|
result = ar->dfs_detector->set_dfs_domain(ar->dfs_detector,
|
|
request->dfs_region);
|
|
if (!result)
|
|
ath10k_warn(ar, "DFS region 0x%X not supported, will trigger radar for every pulse\n",
|
|
request->dfs_region);
|
|
}
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
if (ar->state == ATH10K_STATE_ON)
|
|
ath10k_regd_update(ar);
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
/***************/
|
|
/* TX handlers */
|
|
/***************/
|
|
|
|
static u8 ath10k_tx_h_get_tid(struct ieee80211_hdr *hdr)
|
|
{
|
|
if (ieee80211_is_mgmt(hdr->frame_control))
|
|
return HTT_DATA_TX_EXT_TID_MGMT;
|
|
|
|
if (!ieee80211_is_data_qos(hdr->frame_control))
|
|
return HTT_DATA_TX_EXT_TID_NON_QOS_MCAST_BCAST;
|
|
|
|
if (!is_unicast_ether_addr(ieee80211_get_DA(hdr)))
|
|
return HTT_DATA_TX_EXT_TID_NON_QOS_MCAST_BCAST;
|
|
|
|
return ieee80211_get_qos_ctl(hdr)[0] & IEEE80211_QOS_CTL_TID_MASK;
|
|
}
|
|
|
|
static u8 ath10k_tx_h_get_vdev_id(struct ath10k *ar, struct ieee80211_vif *vif)
|
|
{
|
|
if (vif)
|
|
return ath10k_vif_to_arvif(vif)->vdev_id;
|
|
|
|
if (ar->monitor_started)
|
|
return ar->monitor_vdev_id;
|
|
|
|
ath10k_warn(ar, "failed to resolve vdev id\n");
|
|
return 0;
|
|
}
|
|
|
|
/* HTT Tx uses Native Wifi tx mode which expects 802.11 frames without QoS
|
|
* Control in the header.
|
|
*/
|
|
static void ath10k_tx_h_nwifi(struct ieee80211_hw *hw, struct sk_buff *skb)
|
|
{
|
|
struct ieee80211_hdr *hdr = (void *)skb->data;
|
|
struct ath10k_skb_cb *cb = ATH10K_SKB_CB(skb);
|
|
u8 *qos_ctl;
|
|
|
|
if (!ieee80211_is_data_qos(hdr->frame_control))
|
|
return;
|
|
|
|
qos_ctl = ieee80211_get_qos_ctl(hdr);
|
|
memmove(skb->data + IEEE80211_QOS_CTL_LEN,
|
|
skb->data, (void *)qos_ctl - (void *)skb->data);
|
|
skb_pull(skb, IEEE80211_QOS_CTL_LEN);
|
|
|
|
/* Fw/Hw generates a corrupted QoS Control Field for QoS NullFunc
|
|
* frames. Powersave is handled by the fw/hw so QoS NyllFunc frames are
|
|
* used only for CQM purposes (e.g. hostapd station keepalive ping) so
|
|
* it is safe to downgrade to NullFunc.
|
|
*/
|
|
if (ieee80211_is_qos_nullfunc(hdr->frame_control)) {
|
|
hdr->frame_control &= ~__cpu_to_le16(IEEE80211_STYPE_QOS_DATA);
|
|
cb->htt.tid = HTT_DATA_TX_EXT_TID_NON_QOS_MCAST_BCAST;
|
|
}
|
|
}
|
|
|
|
static void ath10k_tx_wep_key_work(struct work_struct *work)
|
|
{
|
|
struct ath10k_vif *arvif = container_of(work, struct ath10k_vif,
|
|
wep_key_work);
|
|
struct ath10k *ar = arvif->ar;
|
|
int ret, keyidx = arvif->def_wep_key_newidx;
|
|
|
|
mutex_lock(&arvif->ar->conf_mutex);
|
|
|
|
if (arvif->ar->state != ATH10K_STATE_ON)
|
|
goto unlock;
|
|
|
|
if (arvif->def_wep_key_idx == keyidx)
|
|
goto unlock;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d set keyidx %d\n",
|
|
arvif->vdev_id, keyidx);
|
|
|
|
ret = ath10k_wmi_vdev_set_param(arvif->ar,
|
|
arvif->vdev_id,
|
|
arvif->ar->wmi.vdev_param->def_keyid,
|
|
keyidx);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to update wep key index for vdev %d: %d\n",
|
|
arvif->vdev_id,
|
|
ret);
|
|
goto unlock;
|
|
}
|
|
|
|
arvif->def_wep_key_idx = keyidx;
|
|
|
|
unlock:
|
|
mutex_unlock(&arvif->ar->conf_mutex);
|
|
}
|
|
|
|
static void ath10k_tx_h_update_wep_key(struct ieee80211_vif *vif,
|
|
struct ieee80211_key_conf *key,
|
|
struct sk_buff *skb)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct ath10k *ar = arvif->ar;
|
|
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
|
|
|
|
if (!ieee80211_has_protected(hdr->frame_control))
|
|
return;
|
|
|
|
if (!key)
|
|
return;
|
|
|
|
if (key->cipher != WLAN_CIPHER_SUITE_WEP40 &&
|
|
key->cipher != WLAN_CIPHER_SUITE_WEP104)
|
|
return;
|
|
|
|
if (key->keyidx == arvif->def_wep_key_idx)
|
|
return;
|
|
|
|
/* FIXME: Most likely a few frames will be TXed with an old key. Simply
|
|
* queueing frames until key index is updated is not an option because
|
|
* sk_buff may need more processing to be done, e.g. offchannel */
|
|
arvif->def_wep_key_newidx = key->keyidx;
|
|
ieee80211_queue_work(ar->hw, &arvif->wep_key_work);
|
|
}
|
|
|
|
static void ath10k_tx_h_add_p2p_noa_ie(struct ath10k *ar,
|
|
struct ieee80211_vif *vif,
|
|
struct sk_buff *skb)
|
|
{
|
|
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
|
|
/* This is case only for P2P_GO */
|
|
if (arvif->vdev_type != WMI_VDEV_TYPE_AP ||
|
|
arvif->vdev_subtype != WMI_VDEV_SUBTYPE_P2P_GO)
|
|
return;
|
|
|
|
if (unlikely(ieee80211_is_probe_resp(hdr->frame_control))) {
|
|
spin_lock_bh(&ar->data_lock);
|
|
if (arvif->u.ap.noa_data)
|
|
if (!pskb_expand_head(skb, 0, arvif->u.ap.noa_len,
|
|
GFP_ATOMIC))
|
|
memcpy(skb_put(skb, arvif->u.ap.noa_len),
|
|
arvif->u.ap.noa_data,
|
|
arvif->u.ap.noa_len);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
}
|
|
|
|
static bool ath10k_mac_need_offchan_tx_work(struct ath10k *ar)
|
|
{
|
|
/* FIXME: Not really sure since when the behaviour changed. At some
|
|
* point new firmware stopped requiring creation of peer entries for
|
|
* offchannel tx (and actually creating them causes issues with wmi-htc
|
|
* tx credit replenishment and reliability). Assuming it's at least 3.4
|
|
* because that's when the `freq` was introduced to TX_FRM HTT command.
|
|
*/
|
|
return !(ar->htt.target_version_major >= 3 &&
|
|
ar->htt.target_version_minor >= 4);
|
|
}
|
|
|
|
static void ath10k_tx_htt(struct ath10k *ar, struct sk_buff *skb)
|
|
{
|
|
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
|
|
int ret = 0;
|
|
|
|
if (ar->htt.target_version_major >= 3) {
|
|
/* Since HTT 3.0 there is no separate mgmt tx command */
|
|
ret = ath10k_htt_tx(&ar->htt, skb);
|
|
goto exit;
|
|
}
|
|
|
|
if (ieee80211_is_mgmt(hdr->frame_control)) {
|
|
if (test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX,
|
|
ar->fw_features)) {
|
|
if (skb_queue_len(&ar->wmi_mgmt_tx_queue) >=
|
|
ATH10K_MAX_NUM_MGMT_PENDING) {
|
|
ath10k_warn(ar, "reached WMI management transmit queue limit\n");
|
|
ret = -EBUSY;
|
|
goto exit;
|
|
}
|
|
|
|
skb_queue_tail(&ar->wmi_mgmt_tx_queue, skb);
|
|
ieee80211_queue_work(ar->hw, &ar->wmi_mgmt_tx_work);
|
|
} else {
|
|
ret = ath10k_htt_mgmt_tx(&ar->htt, skb);
|
|
}
|
|
} else if (!test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX,
|
|
ar->fw_features) &&
|
|
ieee80211_is_nullfunc(hdr->frame_control)) {
|
|
/* FW does not report tx status properly for NullFunc frames
|
|
* unless they are sent through mgmt tx path. mac80211 sends
|
|
* those frames when it detects link/beacon loss and depends
|
|
* on the tx status to be correct. */
|
|
ret = ath10k_htt_mgmt_tx(&ar->htt, skb);
|
|
} else {
|
|
ret = ath10k_htt_tx(&ar->htt, skb);
|
|
}
|
|
|
|
exit:
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to transmit packet, dropping: %d\n",
|
|
ret);
|
|
ieee80211_free_txskb(ar->hw, skb);
|
|
}
|
|
}
|
|
|
|
void ath10k_offchan_tx_purge(struct ath10k *ar)
|
|
{
|
|
struct sk_buff *skb;
|
|
|
|
for (;;) {
|
|
skb = skb_dequeue(&ar->offchan_tx_queue);
|
|
if (!skb)
|
|
break;
|
|
|
|
ieee80211_free_txskb(ar->hw, skb);
|
|
}
|
|
}
|
|
|
|
void ath10k_offchan_tx_work(struct work_struct *work)
|
|
{
|
|
struct ath10k *ar = container_of(work, struct ath10k, offchan_tx_work);
|
|
struct ath10k_peer *peer;
|
|
struct ieee80211_hdr *hdr;
|
|
struct sk_buff *skb;
|
|
const u8 *peer_addr;
|
|
int vdev_id;
|
|
int ret;
|
|
|
|
/* FW requirement: We must create a peer before FW will send out
|
|
* an offchannel frame. Otherwise the frame will be stuck and
|
|
* never transmitted. We delete the peer upon tx completion.
|
|
* It is unlikely that a peer for offchannel tx will already be
|
|
* present. However it may be in some rare cases so account for that.
|
|
* Otherwise we might remove a legitimate peer and break stuff. */
|
|
|
|
for (;;) {
|
|
skb = skb_dequeue(&ar->offchan_tx_queue);
|
|
if (!skb)
|
|
break;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac offchannel skb %p\n",
|
|
skb);
|
|
|
|
hdr = (struct ieee80211_hdr *)skb->data;
|
|
peer_addr = ieee80211_get_DA(hdr);
|
|
vdev_id = ATH10K_SKB_CB(skb)->vdev_id;
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer = ath10k_peer_find(ar, vdev_id, peer_addr);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (peer)
|
|
/* FIXME: should this use ath10k_warn()? */
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "peer %pM on vdev %d already present\n",
|
|
peer_addr, vdev_id);
|
|
|
|
if (!peer) {
|
|
ret = ath10k_peer_create(ar, vdev_id, peer_addr);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to create peer %pM on vdev %d: %d\n",
|
|
peer_addr, vdev_id, ret);
|
|
}
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
reinit_completion(&ar->offchan_tx_completed);
|
|
ar->offchan_tx_skb = skb;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
ath10k_tx_htt(ar, skb);
|
|
|
|
ret = wait_for_completion_timeout(&ar->offchan_tx_completed,
|
|
3 * HZ);
|
|
if (ret <= 0)
|
|
ath10k_warn(ar, "timed out waiting for offchannel skb %p\n",
|
|
skb);
|
|
|
|
if (!peer) {
|
|
ret = ath10k_peer_delete(ar, vdev_id, peer_addr);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to delete peer %pM on vdev %d: %d\n",
|
|
peer_addr, vdev_id, ret);
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
}
|
|
|
|
void ath10k_mgmt_over_wmi_tx_purge(struct ath10k *ar)
|
|
{
|
|
struct sk_buff *skb;
|
|
|
|
for (;;) {
|
|
skb = skb_dequeue(&ar->wmi_mgmt_tx_queue);
|
|
if (!skb)
|
|
break;
|
|
|
|
ieee80211_free_txskb(ar->hw, skb);
|
|
}
|
|
}
|
|
|
|
void ath10k_mgmt_over_wmi_tx_work(struct work_struct *work)
|
|
{
|
|
struct ath10k *ar = container_of(work, struct ath10k, wmi_mgmt_tx_work);
|
|
struct sk_buff *skb;
|
|
int ret;
|
|
|
|
for (;;) {
|
|
skb = skb_dequeue(&ar->wmi_mgmt_tx_queue);
|
|
if (!skb)
|
|
break;
|
|
|
|
ret = ath10k_wmi_mgmt_tx(ar, skb);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to transmit management frame via WMI: %d\n",
|
|
ret);
|
|
ieee80211_free_txskb(ar->hw, skb);
|
|
}
|
|
}
|
|
}
|
|
|
|
/************/
|
|
/* Scanning */
|
|
/************/
|
|
|
|
void __ath10k_scan_finish(struct ath10k *ar)
|
|
{
|
|
lockdep_assert_held(&ar->data_lock);
|
|
|
|
switch (ar->scan.state) {
|
|
case ATH10K_SCAN_IDLE:
|
|
break;
|
|
case ATH10K_SCAN_RUNNING:
|
|
if (ar->scan.is_roc)
|
|
ieee80211_remain_on_channel_expired(ar->hw);
|
|
case ATH10K_SCAN_ABORTING:
|
|
if (!ar->scan.is_roc)
|
|
ieee80211_scan_completed(ar->hw,
|
|
(ar->scan.state ==
|
|
ATH10K_SCAN_ABORTING));
|
|
/* fall through */
|
|
case ATH10K_SCAN_STARTING:
|
|
ar->scan.state = ATH10K_SCAN_IDLE;
|
|
ar->scan_channel = NULL;
|
|
ath10k_offchan_tx_purge(ar);
|
|
cancel_delayed_work(&ar->scan.timeout);
|
|
complete_all(&ar->scan.completed);
|
|
break;
|
|
}
|
|
}
|
|
|
|
void ath10k_scan_finish(struct ath10k *ar)
|
|
{
|
|
spin_lock_bh(&ar->data_lock);
|
|
__ath10k_scan_finish(ar);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
static int ath10k_scan_stop(struct ath10k *ar)
|
|
{
|
|
struct wmi_stop_scan_arg arg = {
|
|
.req_id = 1, /* FIXME */
|
|
.req_type = WMI_SCAN_STOP_ONE,
|
|
.u.scan_id = ATH10K_SCAN_ID,
|
|
};
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_wmi_stop_scan(ar, &arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to stop wmi scan: %d\n", ret);
|
|
goto out;
|
|
}
|
|
|
|
ret = wait_for_completion_timeout(&ar->scan.completed, 3*HZ);
|
|
if (ret == 0) {
|
|
ath10k_warn(ar, "failed to receive scan abortion completion: timed out\n");
|
|
ret = -ETIMEDOUT;
|
|
} else if (ret > 0) {
|
|
ret = 0;
|
|
}
|
|
|
|
out:
|
|
/* Scan state should be updated upon scan completion but in case
|
|
* firmware fails to deliver the event (for whatever reason) it is
|
|
* desired to clean up scan state anyway. Firmware may have just
|
|
* dropped the scan completion event delivery due to transport pipe
|
|
* being overflown with data and/or it can recover on its own before
|
|
* next scan request is submitted.
|
|
*/
|
|
spin_lock_bh(&ar->data_lock);
|
|
if (ar->scan.state != ATH10K_SCAN_IDLE)
|
|
__ath10k_scan_finish(ar);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_scan_abort(struct ath10k *ar)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
|
|
switch (ar->scan.state) {
|
|
case ATH10K_SCAN_IDLE:
|
|
/* This can happen if timeout worker kicked in and called
|
|
* abortion while scan completion was being processed.
|
|
*/
|
|
break;
|
|
case ATH10K_SCAN_STARTING:
|
|
case ATH10K_SCAN_ABORTING:
|
|
ath10k_warn(ar, "refusing scan abortion due to invalid scan state: %s (%d)\n",
|
|
ath10k_scan_state_str(ar->scan.state),
|
|
ar->scan.state);
|
|
break;
|
|
case ATH10K_SCAN_RUNNING:
|
|
ar->scan.state = ATH10K_SCAN_ABORTING;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
ret = ath10k_scan_stop(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to abort scan: %d\n", ret);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
break;
|
|
}
|
|
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
void ath10k_scan_timeout_work(struct work_struct *work)
|
|
{
|
|
struct ath10k *ar = container_of(work, struct ath10k,
|
|
scan.timeout.work);
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
ath10k_scan_abort(ar);
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
static int ath10k_start_scan(struct ath10k *ar,
|
|
const struct wmi_start_scan_arg *arg)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ret = ath10k_wmi_start_scan(ar, arg);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = wait_for_completion_timeout(&ar->scan.started, 1*HZ);
|
|
if (ret == 0) {
|
|
ret = ath10k_scan_stop(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to stop scan: %d\n", ret);
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
/* Add a 200ms margin to account for event/command processing */
|
|
ieee80211_queue_delayed_work(ar->hw, &ar->scan.timeout,
|
|
msecs_to_jiffies(arg->max_scan_time+200));
|
|
return 0;
|
|
}
|
|
|
|
/**********************/
|
|
/* mac80211 callbacks */
|
|
/**********************/
|
|
|
|
static void ath10k_tx(struct ieee80211_hw *hw,
|
|
struct ieee80211_tx_control *control,
|
|
struct sk_buff *skb)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
|
|
struct ieee80211_vif *vif = info->control.vif;
|
|
struct ieee80211_key_conf *key = info->control.hw_key;
|
|
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
|
|
|
|
/* We should disable CCK RATE due to P2P */
|
|
if (info->flags & IEEE80211_TX_CTL_NO_CCK_RATE)
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "IEEE80211_TX_CTL_NO_CCK_RATE\n");
|
|
|
|
ATH10K_SKB_CB(skb)->htt.is_offchan = false;
|
|
ATH10K_SKB_CB(skb)->htt.tid = ath10k_tx_h_get_tid(hdr);
|
|
ATH10K_SKB_CB(skb)->vdev_id = ath10k_tx_h_get_vdev_id(ar, vif);
|
|
|
|
/* it makes no sense to process injected frames like that */
|
|
if (vif && vif->type != NL80211_IFTYPE_MONITOR) {
|
|
ath10k_tx_h_nwifi(hw, skb);
|
|
ath10k_tx_h_update_wep_key(vif, key, skb);
|
|
ath10k_tx_h_add_p2p_noa_ie(ar, vif, skb);
|
|
ath10k_tx_h_seq_no(vif, skb);
|
|
}
|
|
|
|
if (info->flags & IEEE80211_TX_CTL_TX_OFFCHAN) {
|
|
spin_lock_bh(&ar->data_lock);
|
|
ATH10K_SKB_CB(skb)->htt.freq = ar->scan.roc_freq;
|
|
ATH10K_SKB_CB(skb)->vdev_id = ar->scan.vdev_id;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (ath10k_mac_need_offchan_tx_work(ar)) {
|
|
ATH10K_SKB_CB(skb)->htt.freq = 0;
|
|
ATH10K_SKB_CB(skb)->htt.is_offchan = true;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "queued offchannel skb %p\n",
|
|
skb);
|
|
|
|
skb_queue_tail(&ar->offchan_tx_queue, skb);
|
|
ieee80211_queue_work(hw, &ar->offchan_tx_work);
|
|
return;
|
|
}
|
|
}
|
|
|
|
ath10k_tx_htt(ar, skb);
|
|
}
|
|
|
|
/* Must not be called with conf_mutex held as workers can use that also. */
|
|
void ath10k_drain_tx(struct ath10k *ar)
|
|
{
|
|
/* make sure rcu-protected mac80211 tx path itself is drained */
|
|
synchronize_net();
|
|
|
|
ath10k_offchan_tx_purge(ar);
|
|
ath10k_mgmt_over_wmi_tx_purge(ar);
|
|
|
|
cancel_work_sync(&ar->offchan_tx_work);
|
|
cancel_work_sync(&ar->wmi_mgmt_tx_work);
|
|
}
|
|
|
|
void ath10k_halt(struct ath10k *ar)
|
|
{
|
|
struct ath10k_vif *arvif;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
clear_bit(ATH10K_CAC_RUNNING, &ar->dev_flags);
|
|
ar->filter_flags = 0;
|
|
ar->monitor = false;
|
|
|
|
if (ar->monitor_started)
|
|
ath10k_monitor_stop(ar);
|
|
|
|
ar->monitor_started = false;
|
|
|
|
ath10k_scan_finish(ar);
|
|
ath10k_peer_cleanup_all(ar);
|
|
ath10k_core_stop(ar);
|
|
ath10k_hif_power_down(ar);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
list_for_each_entry(arvif, &ar->arvifs, list)
|
|
ath10k_mac_vif_beacon_cleanup(arvif);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
static int ath10k_get_antenna(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (ar->cfg_tx_chainmask) {
|
|
*tx_ant = ar->cfg_tx_chainmask;
|
|
*rx_ant = ar->cfg_rx_chainmask;
|
|
} else {
|
|
*tx_ant = ar->supp_tx_chainmask;
|
|
*rx_ant = ar->supp_rx_chainmask;
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ath10k_check_chain_mask(struct ath10k *ar, u32 cm, const char *dbg)
|
|
{
|
|
/* It is not clear that allowing gaps in chainmask
|
|
* is helpful. Probably it will not do what user
|
|
* is hoping for, so warn in that case.
|
|
*/
|
|
if (cm == 15 || cm == 7 || cm == 3 || cm == 1 || cm == 0)
|
|
return;
|
|
|
|
ath10k_warn(ar, "mac %s antenna chainmask may be invalid: 0x%x. Suggested values: 15, 7, 3, 1 or 0.\n",
|
|
dbg, cm);
|
|
}
|
|
|
|
static int __ath10k_set_antenna(struct ath10k *ar, u32 tx_ant, u32 rx_ant)
|
|
{
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ath10k_check_chain_mask(ar, tx_ant, "tx");
|
|
ath10k_check_chain_mask(ar, rx_ant, "rx");
|
|
|
|
ar->cfg_tx_chainmask = tx_ant;
|
|
ar->cfg_rx_chainmask = rx_ant;
|
|
|
|
if ((ar->state != ATH10K_STATE_ON) &&
|
|
(ar->state != ATH10K_STATE_RESTARTED))
|
|
return 0;
|
|
|
|
ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->tx_chain_mask,
|
|
tx_ant);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set tx-chainmask: %d, req 0x%x\n",
|
|
ret, tx_ant);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->rx_chain_mask,
|
|
rx_ant);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set rx-chainmask: %d, req 0x%x\n",
|
|
ret, rx_ant);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_set_antenna(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
int ret;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
ret = __ath10k_set_antenna(ar, tx_ant, rx_ant);
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_start(struct ieee80211_hw *hw)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
int ret = 0;
|
|
|
|
/*
|
|
* This makes sense only when restarting hw. It is harmless to call
|
|
* uncoditionally. This is necessary to make sure no HTT/WMI tx
|
|
* commands will be submitted while restarting.
|
|
*/
|
|
ath10k_drain_tx(ar);
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
switch (ar->state) {
|
|
case ATH10K_STATE_OFF:
|
|
ar->state = ATH10K_STATE_ON;
|
|
break;
|
|
case ATH10K_STATE_RESTARTING:
|
|
ath10k_halt(ar);
|
|
ar->state = ATH10K_STATE_RESTARTED;
|
|
break;
|
|
case ATH10K_STATE_ON:
|
|
case ATH10K_STATE_RESTARTED:
|
|
case ATH10K_STATE_WEDGED:
|
|
WARN_ON(1);
|
|
ret = -EINVAL;
|
|
goto err;
|
|
case ATH10K_STATE_UTF:
|
|
ret = -EBUSY;
|
|
goto err;
|
|
}
|
|
|
|
ret = ath10k_hif_power_up(ar);
|
|
if (ret) {
|
|
ath10k_err(ar, "Could not init hif: %d\n", ret);
|
|
goto err_off;
|
|
}
|
|
|
|
ret = ath10k_core_start(ar, ATH10K_FIRMWARE_MODE_NORMAL);
|
|
if (ret) {
|
|
ath10k_err(ar, "Could not init core: %d\n", ret);
|
|
goto err_power_down;
|
|
}
|
|
|
|
ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->pmf_qos, 1);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to enable PMF QOS: %d\n", ret);
|
|
goto err_core_stop;
|
|
}
|
|
|
|
ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->dynamic_bw, 1);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to enable dynamic BW: %d\n", ret);
|
|
goto err_core_stop;
|
|
}
|
|
|
|
if (ar->cfg_tx_chainmask)
|
|
__ath10k_set_antenna(ar, ar->cfg_tx_chainmask,
|
|
ar->cfg_rx_chainmask);
|
|
|
|
/*
|
|
* By default FW set ARP frames ac to voice (6). In that case ARP
|
|
* exchange is not working properly for UAPSD enabled AP. ARP requests
|
|
* which arrives with access category 0 are processed by network stack
|
|
* and send back with access category 0, but FW changes access category
|
|
* to 6. Set ARP frames access category to best effort (0) solves
|
|
* this problem.
|
|
*/
|
|
|
|
ret = ath10k_wmi_pdev_set_param(ar,
|
|
ar->wmi.pdev_param->arp_ac_override, 0);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set arp ac override parameter: %d\n",
|
|
ret);
|
|
goto err_core_stop;
|
|
}
|
|
|
|
ar->num_started_vdevs = 0;
|
|
ath10k_regd_update(ar);
|
|
|
|
ath10k_spectral_start(ar);
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return 0;
|
|
|
|
err_core_stop:
|
|
ath10k_core_stop(ar);
|
|
|
|
err_power_down:
|
|
ath10k_hif_power_down(ar);
|
|
|
|
err_off:
|
|
ar->state = ATH10K_STATE_OFF;
|
|
|
|
err:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_stop(struct ieee80211_hw *hw)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
|
|
ath10k_drain_tx(ar);
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
if (ar->state != ATH10K_STATE_OFF) {
|
|
ath10k_halt(ar);
|
|
ar->state = ATH10K_STATE_OFF;
|
|
}
|
|
mutex_unlock(&ar->conf_mutex);
|
|
|
|
cancel_delayed_work_sync(&ar->scan.timeout);
|
|
cancel_work_sync(&ar->restart_work);
|
|
}
|
|
|
|
static int ath10k_config_ps(struct ath10k *ar)
|
|
{
|
|
struct ath10k_vif *arvif;
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
list_for_each_entry(arvif, &ar->arvifs, list) {
|
|
ret = ath10k_mac_vif_setup_ps(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to setup powersave: %d\n", ret);
|
|
break;
|
|
}
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const char *chandef_get_width(enum nl80211_chan_width width)
|
|
{
|
|
switch (width) {
|
|
case NL80211_CHAN_WIDTH_20_NOHT:
|
|
return "20 (noht)";
|
|
case NL80211_CHAN_WIDTH_20:
|
|
return "20";
|
|
case NL80211_CHAN_WIDTH_40:
|
|
return "40";
|
|
case NL80211_CHAN_WIDTH_80:
|
|
return "80";
|
|
case NL80211_CHAN_WIDTH_80P80:
|
|
return "80+80";
|
|
case NL80211_CHAN_WIDTH_160:
|
|
return "160";
|
|
case NL80211_CHAN_WIDTH_5:
|
|
return "5";
|
|
case NL80211_CHAN_WIDTH_10:
|
|
return "10";
|
|
}
|
|
return "?";
|
|
}
|
|
|
|
static void ath10k_config_chan(struct ath10k *ar)
|
|
{
|
|
struct ath10k_vif *arvif;
|
|
int ret;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac config channel to %dMHz (cf1 %dMHz cf2 %dMHz width %s)\n",
|
|
ar->chandef.chan->center_freq,
|
|
ar->chandef.center_freq1,
|
|
ar->chandef.center_freq2,
|
|
chandef_get_width(ar->chandef.width));
|
|
|
|
/* First stop monitor interface. Some FW versions crash if there's a
|
|
* lone monitor interface. */
|
|
if (ar->monitor_started)
|
|
ath10k_monitor_stop(ar);
|
|
|
|
list_for_each_entry(arvif, &ar->arvifs, list) {
|
|
if (!arvif->is_started)
|
|
continue;
|
|
|
|
if (!arvif->is_up)
|
|
continue;
|
|
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_MONITOR)
|
|
continue;
|
|
|
|
ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to down vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
continue;
|
|
}
|
|
}
|
|
|
|
/* all vdevs are downed now - attempt to restart and re-up them */
|
|
|
|
list_for_each_entry(arvif, &ar->arvifs, list) {
|
|
if (!arvif->is_started)
|
|
continue;
|
|
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_MONITOR)
|
|
continue;
|
|
|
|
ret = ath10k_vdev_restart(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to restart vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
continue;
|
|
}
|
|
|
|
if (!arvif->is_up)
|
|
continue;
|
|
|
|
ret = ath10k_wmi_vdev_up(arvif->ar, arvif->vdev_id, arvif->aid,
|
|
arvif->bssid);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to bring vdev up %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
continue;
|
|
}
|
|
}
|
|
|
|
ath10k_monitor_recalc(ar);
|
|
}
|
|
|
|
static int ath10k_mac_txpower_setup(struct ath10k *ar, int txpower)
|
|
{
|
|
int ret;
|
|
u32 param;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac txpower %d\n", txpower);
|
|
|
|
param = ar->wmi.pdev_param->txpower_limit2g;
|
|
ret = ath10k_wmi_pdev_set_param(ar, param, txpower * 2);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set 2g txpower %d: %d\n",
|
|
txpower, ret);
|
|
return ret;
|
|
}
|
|
|
|
param = ar->wmi.pdev_param->txpower_limit5g;
|
|
ret = ath10k_wmi_pdev_set_param(ar, param, txpower * 2);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set 5g txpower %d: %d\n",
|
|
txpower, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_mac_txpower_recalc(struct ath10k *ar)
|
|
{
|
|
struct ath10k_vif *arvif;
|
|
int ret, txpower = -1;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
list_for_each_entry(arvif, &ar->arvifs, list) {
|
|
WARN_ON(arvif->txpower < 0);
|
|
|
|
if (txpower == -1)
|
|
txpower = arvif->txpower;
|
|
else
|
|
txpower = min(txpower, arvif->txpower);
|
|
}
|
|
|
|
if (WARN_ON(txpower == -1))
|
|
return -EINVAL;
|
|
|
|
ret = ath10k_mac_txpower_setup(ar, txpower);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to setup tx power %d: %d\n",
|
|
txpower, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_config(struct ieee80211_hw *hw, u32 changed)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ieee80211_conf *conf = &hw->conf;
|
|
int ret = 0;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac config channel %dMHz flags 0x%x radar %d\n",
|
|
conf->chandef.chan->center_freq,
|
|
conf->chandef.chan->flags,
|
|
conf->radar_enabled);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
ar->rx_channel = conf->chandef.chan;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
ar->radar_enabled = conf->radar_enabled;
|
|
ath10k_recalc_radar_detection(ar);
|
|
|
|
if (!cfg80211_chandef_identical(&ar->chandef, &conf->chandef)) {
|
|
ar->chandef = conf->chandef;
|
|
ath10k_config_chan(ar);
|
|
}
|
|
}
|
|
|
|
if (changed & IEEE80211_CONF_CHANGE_PS)
|
|
ath10k_config_ps(ar);
|
|
|
|
if (changed & IEEE80211_CONF_CHANGE_MONITOR) {
|
|
ar->monitor = conf->flags & IEEE80211_CONF_MONITOR;
|
|
ret = ath10k_monitor_recalc(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to recalc monitor: %d\n", ret);
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static u32 get_nss_from_chainmask(u16 chain_mask)
|
|
{
|
|
if ((chain_mask & 0x15) == 0x15)
|
|
return 4;
|
|
else if ((chain_mask & 0x7) == 0x7)
|
|
return 3;
|
|
else if ((chain_mask & 0x3) == 0x3)
|
|
return 2;
|
|
return 1;
|
|
}
|
|
|
|
/*
|
|
* TODO:
|
|
* Figure out how to handle WMI_VDEV_SUBTYPE_P2P_DEVICE,
|
|
* because we will send mgmt frames without CCK. This requirement
|
|
* for P2P_FIND/GO_NEG should be handled by checking CCK flag
|
|
* in the TX packet.
|
|
*/
|
|
static int ath10k_add_interface(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
enum wmi_sta_powersave_param param;
|
|
int ret = 0;
|
|
u32 value;
|
|
int bit;
|
|
u32 vdev_param;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
memset(arvif, 0, sizeof(*arvif));
|
|
|
|
arvif->ar = ar;
|
|
arvif->vif = vif;
|
|
|
|
INIT_WORK(&arvif->wep_key_work, ath10k_tx_wep_key_work);
|
|
INIT_LIST_HEAD(&arvif->list);
|
|
|
|
if (ar->free_vdev_map == 0) {
|
|
ath10k_warn(ar, "Free vdev map is empty, no more interfaces allowed.\n");
|
|
ret = -EBUSY;
|
|
goto err;
|
|
}
|
|
bit = __ffs64(ar->free_vdev_map);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac create vdev %i map %llx\n",
|
|
bit, ar->free_vdev_map);
|
|
|
|
arvif->vdev_id = bit;
|
|
arvif->vdev_subtype = WMI_VDEV_SUBTYPE_NONE;
|
|
|
|
switch (vif->type) {
|
|
case NL80211_IFTYPE_P2P_DEVICE:
|
|
arvif->vdev_type = WMI_VDEV_TYPE_STA;
|
|
arvif->vdev_subtype = WMI_VDEV_SUBTYPE_P2P_DEVICE;
|
|
break;
|
|
case NL80211_IFTYPE_UNSPECIFIED:
|
|
case NL80211_IFTYPE_STATION:
|
|
arvif->vdev_type = WMI_VDEV_TYPE_STA;
|
|
if (vif->p2p)
|
|
arvif->vdev_subtype = WMI_VDEV_SUBTYPE_P2P_CLIENT;
|
|
break;
|
|
case NL80211_IFTYPE_ADHOC:
|
|
arvif->vdev_type = WMI_VDEV_TYPE_IBSS;
|
|
break;
|
|
case NL80211_IFTYPE_AP:
|
|
arvif->vdev_type = WMI_VDEV_TYPE_AP;
|
|
|
|
if (vif->p2p)
|
|
arvif->vdev_subtype = WMI_VDEV_SUBTYPE_P2P_GO;
|
|
break;
|
|
case NL80211_IFTYPE_MONITOR:
|
|
arvif->vdev_type = WMI_VDEV_TYPE_MONITOR;
|
|
break;
|
|
default:
|
|
WARN_ON(1);
|
|
break;
|
|
}
|
|
|
|
/* Some firmware revisions don't wait for beacon tx completion before
|
|
* sending another SWBA event. This could lead to hardware using old
|
|
* (freed) beacon data in some cases, e.g. tx credit starvation
|
|
* combined with missed TBTT. This is very very rare.
|
|
*
|
|
* On non-IOMMU-enabled hosts this could be a possible security issue
|
|
* because hw could beacon some random data on the air. On
|
|
* IOMMU-enabled hosts DMAR faults would occur in most cases and target
|
|
* device would crash.
|
|
*
|
|
* Since there are no beacon tx completions (implicit nor explicit)
|
|
* propagated to host the only workaround for this is to allocate a
|
|
* DMA-coherent buffer for a lifetime of a vif and use it for all
|
|
* beacon tx commands. Worst case for this approach is some beacons may
|
|
* become corrupted, e.g. have garbled IEs or out-of-date TIM bitmap.
|
|
*/
|
|
if (vif->type == NL80211_IFTYPE_ADHOC ||
|
|
vif->type == NL80211_IFTYPE_AP) {
|
|
arvif->beacon_buf = dma_zalloc_coherent(ar->dev,
|
|
IEEE80211_MAX_FRAME_LEN,
|
|
&arvif->beacon_paddr,
|
|
GFP_ATOMIC);
|
|
if (!arvif->beacon_buf) {
|
|
ret = -ENOMEM;
|
|
ath10k_warn(ar, "failed to allocate beacon buffer: %d\n",
|
|
ret);
|
|
goto err;
|
|
}
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev create %d (add interface) type %d subtype %d bcnmode %s\n",
|
|
arvif->vdev_id, arvif->vdev_type, arvif->vdev_subtype,
|
|
arvif->beacon_buf ? "single-buf" : "per-skb");
|
|
|
|
ret = ath10k_wmi_vdev_create(ar, arvif->vdev_id, arvif->vdev_type,
|
|
arvif->vdev_subtype, vif->addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to create WMI vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err;
|
|
}
|
|
|
|
ar->free_vdev_map &= ~(1LL << arvif->vdev_id);
|
|
list_add(&arvif->list, &ar->arvifs);
|
|
|
|
vdev_param = ar->wmi.vdev_param->def_keyid;
|
|
ret = ath10k_wmi_vdev_set_param(ar, 0, vdev_param,
|
|
arvif->def_wep_key_idx);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set vdev %i default key id: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_vdev_delete;
|
|
}
|
|
|
|
vdev_param = ar->wmi.vdev_param->tx_encap_type;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
ATH10K_HW_TXRX_NATIVE_WIFI);
|
|
/* 10.X firmware does not support this VDEV parameter. Do not warn */
|
|
if (ret && ret != -EOPNOTSUPP) {
|
|
ath10k_warn(ar, "failed to set vdev %i TX encapsulation: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_vdev_delete;
|
|
}
|
|
|
|
if (ar->cfg_tx_chainmask) {
|
|
u16 nss = get_nss_from_chainmask(ar->cfg_tx_chainmask);
|
|
|
|
vdev_param = ar->wmi.vdev_param->nss;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
nss);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set vdev %i chainmask 0x%x, nss %i: %d\n",
|
|
arvif->vdev_id, ar->cfg_tx_chainmask, nss,
|
|
ret);
|
|
goto err_vdev_delete;
|
|
}
|
|
}
|
|
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
|
|
ret = ath10k_peer_create(ar, arvif->vdev_id, vif->addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to create vdev %i peer for AP: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_vdev_delete;
|
|
}
|
|
|
|
ret = ath10k_mac_set_kickout(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set vdev %i kickout parameters: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_peer_delete;
|
|
}
|
|
}
|
|
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_STA) {
|
|
param = WMI_STA_PS_PARAM_RX_WAKE_POLICY;
|
|
value = WMI_STA_PS_RX_WAKE_POLICY_WAKE;
|
|
ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id,
|
|
param, value);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set vdev %i RX wake policy: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_peer_delete;
|
|
}
|
|
|
|
ret = ath10k_mac_vif_recalc_ps_wake_threshold(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalc ps wake threshold on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_peer_delete;
|
|
}
|
|
|
|
ret = ath10k_mac_vif_recalc_ps_poll_count(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalc ps poll count on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_peer_delete;
|
|
}
|
|
}
|
|
|
|
ret = ath10k_mac_set_rts(arvif, ar->hw->wiphy->rts_threshold);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set rts threshold for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_peer_delete;
|
|
}
|
|
|
|
ret = ath10k_mac_set_frag(arvif, ar->hw->wiphy->frag_threshold);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set frag threshold for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
goto err_peer_delete;
|
|
}
|
|
|
|
arvif->txpower = vif->bss_conf.txpower;
|
|
ret = ath10k_mac_txpower_recalc(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalc tx power: %d\n", ret);
|
|
goto err_peer_delete;
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return 0;
|
|
|
|
err_peer_delete:
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_AP)
|
|
ath10k_wmi_peer_delete(ar, arvif->vdev_id, vif->addr);
|
|
|
|
err_vdev_delete:
|
|
ath10k_wmi_vdev_delete(ar, arvif->vdev_id);
|
|
ar->free_vdev_map |= 1LL << arvif->vdev_id;
|
|
list_del(&arvif->list);
|
|
|
|
err:
|
|
if (arvif->beacon_buf) {
|
|
dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN,
|
|
arvif->beacon_buf, arvif->beacon_paddr);
|
|
arvif->beacon_buf = NULL;
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_remove_interface(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
int ret;
|
|
|
|
cancel_work_sync(&arvif->wep_key_work);
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
ath10k_mac_vif_beacon_cleanup(arvif);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
ret = ath10k_spectral_vif_stop(arvif);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to stop spectral for vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
|
|
ar->free_vdev_map |= 1LL << arvif->vdev_id;
|
|
list_del(&arvif->list);
|
|
|
|
if (arvif->vdev_type == WMI_VDEV_TYPE_AP) {
|
|
ret = ath10k_peer_delete(arvif->ar, arvif->vdev_id, vif->addr);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to remove peer for AP vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
|
|
kfree(arvif->u.ap.noa_data);
|
|
}
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %i delete (remove interface)\n",
|
|
arvif->vdev_id);
|
|
|
|
ret = ath10k_wmi_vdev_delete(ar, arvif->vdev_id);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to delete WMI vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
|
|
ath10k_peer_cleanup(ar, arvif->vdev_id);
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
/*
|
|
* FIXME: Has to be verified.
|
|
*/
|
|
#define SUPPORTED_FILTERS \
|
|
(FIF_PROMISC_IN_BSS | \
|
|
FIF_ALLMULTI | \
|
|
FIF_CONTROL | \
|
|
FIF_PSPOLL | \
|
|
FIF_OTHER_BSS | \
|
|
FIF_BCN_PRBRESP_PROMISC | \
|
|
FIF_PROBE_REQ | \
|
|
FIF_FCSFAIL)
|
|
|
|
static void ath10k_configure_filter(struct ieee80211_hw *hw,
|
|
unsigned int changed_flags,
|
|
unsigned int *total_flags,
|
|
u64 multicast)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
int ret;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
changed_flags &= SUPPORTED_FILTERS;
|
|
*total_flags &= SUPPORTED_FILTERS;
|
|
ar->filter_flags = *total_flags;
|
|
|
|
ret = ath10k_monitor_recalc(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to recalc montior: %d\n", ret);
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
static void ath10k_bss_info_changed(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_bss_conf *info,
|
|
u32 changed)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
int ret = 0;
|
|
u32 vdev_param, pdev_param, slottime, preamble;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (changed & BSS_CHANGED_IBSS)
|
|
ath10k_control_ibss(arvif, info, vif->addr);
|
|
|
|
if (changed & BSS_CHANGED_BEACON_INT) {
|
|
arvif->beacon_interval = info->beacon_int;
|
|
vdev_param = ar->wmi.vdev_param->beacon_interval;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
arvif->beacon_interval);
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d beacon_interval %d\n",
|
|
arvif->vdev_id, arvif->beacon_interval);
|
|
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set beacon interval for vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_BEACON) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"vdev %d set beacon tx mode to staggered\n",
|
|
arvif->vdev_id);
|
|
|
|
pdev_param = ar->wmi.pdev_param->beacon_tx_mode;
|
|
ret = ath10k_wmi_pdev_set_param(ar, pdev_param,
|
|
WMI_BEACON_STAGGERED_MODE);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set beacon mode for vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_BEACON_INFO) {
|
|
arvif->dtim_period = info->dtim_period;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d dtim_period %d\n",
|
|
arvif->vdev_id, arvif->dtim_period);
|
|
|
|
vdev_param = ar->wmi.vdev_param->dtim_period;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
arvif->dtim_period);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set dtim period for vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_SSID &&
|
|
vif->type == NL80211_IFTYPE_AP) {
|
|
arvif->u.ap.ssid_len = info->ssid_len;
|
|
if (info->ssid_len)
|
|
memcpy(arvif->u.ap.ssid, info->ssid, info->ssid_len);
|
|
arvif->u.ap.hidden_ssid = info->hidden_ssid;
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_BSSID && !is_zero_ether_addr(info->bssid))
|
|
ether_addr_copy(arvif->bssid, info->bssid);
|
|
|
|
if (changed & BSS_CHANGED_BEACON_ENABLED)
|
|
ath10k_control_beaconing(arvif, info);
|
|
|
|
if (changed & BSS_CHANGED_ERP_CTS_PROT) {
|
|
arvif->use_cts_prot = info->use_cts_prot;
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d cts_prot %d\n",
|
|
arvif->vdev_id, info->use_cts_prot);
|
|
|
|
ret = ath10k_recalc_rtscts_prot(arvif);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to recalculate rts/cts prot for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_ERP_SLOT) {
|
|
if (info->use_short_slot)
|
|
slottime = WMI_VDEV_SLOT_TIME_SHORT; /* 9us */
|
|
|
|
else
|
|
slottime = WMI_VDEV_SLOT_TIME_LONG; /* 20us */
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d slot_time %d\n",
|
|
arvif->vdev_id, slottime);
|
|
|
|
vdev_param = ar->wmi.vdev_param->slot_time;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
slottime);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set erp slot for vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_ERP_PREAMBLE) {
|
|
if (info->use_short_preamble)
|
|
preamble = WMI_VDEV_PREAMBLE_SHORT;
|
|
else
|
|
preamble = WMI_VDEV_PREAMBLE_LONG;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d preamble %dn",
|
|
arvif->vdev_id, preamble);
|
|
|
|
vdev_param = ar->wmi.vdev_param->preamble;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
preamble);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set preamble for vdev %d: %i\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_ASSOC) {
|
|
if (info->assoc) {
|
|
/* Workaround: Make sure monitor vdev is not running
|
|
* when associating to prevent some firmware revisions
|
|
* (e.g. 10.1 and 10.2) from crashing.
|
|
*/
|
|
if (ar->monitor_started)
|
|
ath10k_monitor_stop(ar);
|
|
ath10k_bss_assoc(hw, vif, info);
|
|
ath10k_monitor_recalc(ar);
|
|
} else {
|
|
ath10k_bss_disassoc(hw, vif);
|
|
}
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_TXPOWER) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev_id %i txpower %d\n",
|
|
arvif->vdev_id, info->txpower);
|
|
|
|
arvif->txpower = info->txpower;
|
|
ret = ath10k_mac_txpower_recalc(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to recalc tx power: %d\n", ret);
|
|
}
|
|
|
|
if (changed & BSS_CHANGED_PS) {
|
|
ret = ath10k_mac_vif_setup_ps(arvif);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to setup ps on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
static int ath10k_hw_scan(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_scan_request *hw_req)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct cfg80211_scan_request *req = &hw_req->req;
|
|
struct wmi_start_scan_arg arg;
|
|
int ret = 0;
|
|
int i;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
switch (ar->scan.state) {
|
|
case ATH10K_SCAN_IDLE:
|
|
reinit_completion(&ar->scan.started);
|
|
reinit_completion(&ar->scan.completed);
|
|
ar->scan.state = ATH10K_SCAN_STARTING;
|
|
ar->scan.is_roc = false;
|
|
ar->scan.vdev_id = arvif->vdev_id;
|
|
ret = 0;
|
|
break;
|
|
case ATH10K_SCAN_STARTING:
|
|
case ATH10K_SCAN_RUNNING:
|
|
case ATH10K_SCAN_ABORTING:
|
|
ret = -EBUSY;
|
|
break;
|
|
}
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (ret)
|
|
goto exit;
|
|
|
|
memset(&arg, 0, sizeof(arg));
|
|
ath10k_wmi_start_scan_init(ar, &arg);
|
|
arg.vdev_id = arvif->vdev_id;
|
|
arg.scan_id = ATH10K_SCAN_ID;
|
|
|
|
if (!req->no_cck)
|
|
arg.scan_ctrl_flags |= WMI_SCAN_ADD_CCK_RATES;
|
|
|
|
if (req->ie_len) {
|
|
arg.ie_len = req->ie_len;
|
|
memcpy(arg.ie, req->ie, arg.ie_len);
|
|
}
|
|
|
|
if (req->n_ssids) {
|
|
arg.n_ssids = req->n_ssids;
|
|
for (i = 0; i < arg.n_ssids; i++) {
|
|
arg.ssids[i].len = req->ssids[i].ssid_len;
|
|
arg.ssids[i].ssid = req->ssids[i].ssid;
|
|
}
|
|
} else {
|
|
arg.scan_ctrl_flags |= WMI_SCAN_FLAG_PASSIVE;
|
|
}
|
|
|
|
if (req->n_channels) {
|
|
arg.n_channels = req->n_channels;
|
|
for (i = 0; i < arg.n_channels; i++)
|
|
arg.channels[i] = req->channels[i]->center_freq;
|
|
}
|
|
|
|
ret = ath10k_start_scan(ar, &arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to start hw scan: %d\n", ret);
|
|
spin_lock_bh(&ar->data_lock);
|
|
ar->scan.state = ATH10K_SCAN_IDLE;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
}
|
|
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_cancel_hw_scan(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
ath10k_scan_abort(ar);
|
|
mutex_unlock(&ar->conf_mutex);
|
|
|
|
cancel_delayed_work_sync(&ar->scan.timeout);
|
|
}
|
|
|
|
static void ath10k_set_key_h_def_keyidx(struct ath10k *ar,
|
|
struct ath10k_vif *arvif,
|
|
enum set_key_cmd cmd,
|
|
struct ieee80211_key_conf *key)
|
|
{
|
|
u32 vdev_param = arvif->ar->wmi.vdev_param->def_keyid;
|
|
int ret;
|
|
|
|
/* 10.1 firmware branch requires default key index to be set to group
|
|
* key index after installing it. Otherwise FW/HW Txes corrupted
|
|
* frames with multi-vif APs. This is not required for main firmware
|
|
* branch (e.g. 636).
|
|
*
|
|
* FIXME: This has been tested only in AP. It remains unknown if this
|
|
* is required for multi-vif STA interfaces on 10.1 */
|
|
|
|
if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
|
|
return;
|
|
|
|
if (key->cipher == WLAN_CIPHER_SUITE_WEP40)
|
|
return;
|
|
|
|
if (key->cipher == WLAN_CIPHER_SUITE_WEP104)
|
|
return;
|
|
|
|
if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE)
|
|
return;
|
|
|
|
if (cmd != SET_KEY)
|
|
return;
|
|
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
key->keyidx);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set vdev %i group key as default key: %d\n",
|
|
arvif->vdev_id, ret);
|
|
}
|
|
|
|
static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
|
|
struct ieee80211_vif *vif, struct ieee80211_sta *sta,
|
|
struct ieee80211_key_conf *key)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct ath10k_peer *peer;
|
|
const u8 *peer_addr;
|
|
bool is_wep = key->cipher == WLAN_CIPHER_SUITE_WEP40 ||
|
|
key->cipher == WLAN_CIPHER_SUITE_WEP104;
|
|
int ret = 0;
|
|
|
|
if (key->keyidx > WMI_MAX_KEY_INDEX)
|
|
return -ENOSPC;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (sta)
|
|
peer_addr = sta->addr;
|
|
else if (arvif->vdev_type == WMI_VDEV_TYPE_STA)
|
|
peer_addr = vif->bss_conf.bssid;
|
|
else
|
|
peer_addr = vif->addr;
|
|
|
|
key->hw_key_idx = key->keyidx;
|
|
|
|
/* the peer should not disappear in mid-way (unless FW goes awry) since
|
|
* we already hold conf_mutex. we just make sure its there now. */
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer = ath10k_peer_find(ar, arvif->vdev_id, peer_addr);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (!peer) {
|
|
if (cmd == SET_KEY) {
|
|
ath10k_warn(ar, "failed to install key for non-existent peer %pM\n",
|
|
peer_addr);
|
|
ret = -EOPNOTSUPP;
|
|
goto exit;
|
|
} else {
|
|
/* if the peer doesn't exist there is no key to disable
|
|
* anymore */
|
|
goto exit;
|
|
}
|
|
}
|
|
|
|
if (is_wep) {
|
|
if (cmd == SET_KEY)
|
|
arvif->wep_keys[key->keyidx] = key;
|
|
else
|
|
arvif->wep_keys[key->keyidx] = NULL;
|
|
|
|
if (cmd == DISABLE_KEY)
|
|
ath10k_clear_vdev_key(arvif, key);
|
|
}
|
|
|
|
ret = ath10k_install_key(arvif, key, cmd, peer_addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to install key for vdev %i peer %pM: %d\n",
|
|
arvif->vdev_id, peer_addr, ret);
|
|
goto exit;
|
|
}
|
|
|
|
ath10k_set_key_h_def_keyidx(ar, arvif, cmd, key);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
peer = ath10k_peer_find(ar, arvif->vdev_id, peer_addr);
|
|
if (peer && cmd == SET_KEY)
|
|
peer->keys[key->keyidx] = key;
|
|
else if (peer && cmd == DISABLE_KEY)
|
|
peer->keys[key->keyidx] = NULL;
|
|
else if (peer == NULL)
|
|
/* impossible unless FW goes crazy */
|
|
ath10k_warn(ar, "Peer %pM disappeared!\n", peer_addr);
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_sta_rc_update_wk(struct work_struct *wk)
|
|
{
|
|
struct ath10k *ar;
|
|
struct ath10k_vif *arvif;
|
|
struct ath10k_sta *arsta;
|
|
struct ieee80211_sta *sta;
|
|
u32 changed, bw, nss, smps;
|
|
int err;
|
|
|
|
arsta = container_of(wk, struct ath10k_sta, update_wk);
|
|
sta = container_of((void *)arsta, struct ieee80211_sta, drv_priv);
|
|
arvif = arsta->arvif;
|
|
ar = arvif->ar;
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
|
|
changed = arsta->changed;
|
|
arsta->changed = 0;
|
|
|
|
bw = arsta->bw;
|
|
nss = arsta->nss;
|
|
smps = arsta->smps;
|
|
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (changed & IEEE80211_RC_BW_CHANGED) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac update sta %pM peer bw %d\n",
|
|
sta->addr, bw);
|
|
|
|
err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr,
|
|
WMI_PEER_CHAN_WIDTH, bw);
|
|
if (err)
|
|
ath10k_warn(ar, "failed to update STA %pM peer bw %d: %d\n",
|
|
sta->addr, bw, err);
|
|
}
|
|
|
|
if (changed & IEEE80211_RC_NSS_CHANGED) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac update sta %pM nss %d\n",
|
|
sta->addr, nss);
|
|
|
|
err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr,
|
|
WMI_PEER_NSS, nss);
|
|
if (err)
|
|
ath10k_warn(ar, "failed to update STA %pM nss %d: %d\n",
|
|
sta->addr, nss, err);
|
|
}
|
|
|
|
if (changed & IEEE80211_RC_SMPS_CHANGED) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac update sta %pM smps %d\n",
|
|
sta->addr, smps);
|
|
|
|
err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr,
|
|
WMI_PEER_SMPS_STATE, smps);
|
|
if (err)
|
|
ath10k_warn(ar, "failed to update STA %pM smps %d: %d\n",
|
|
sta->addr, smps, err);
|
|
}
|
|
|
|
if (changed & IEEE80211_RC_SUPP_RATES_CHANGED) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac update sta %pM supp rates\n",
|
|
sta->addr);
|
|
|
|
err = ath10k_station_assoc(ar, arvif->vif, sta, true);
|
|
if (err)
|
|
ath10k_warn(ar, "failed to reassociate station: %pM\n",
|
|
sta->addr);
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
static int ath10k_mac_inc_num_stations(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (arvif->vdev_type != WMI_VDEV_TYPE_AP &&
|
|
arvif->vdev_type != WMI_VDEV_TYPE_IBSS)
|
|
return 0;
|
|
|
|
if (ar->num_stations >= ar->max_num_stations)
|
|
return -ENOBUFS;
|
|
|
|
ar->num_stations++;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void ath10k_mac_dec_num_stations(struct ath10k_vif *arvif)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (arvif->vdev_type != WMI_VDEV_TYPE_AP &&
|
|
arvif->vdev_type != WMI_VDEV_TYPE_IBSS)
|
|
return;
|
|
|
|
ar->num_stations--;
|
|
}
|
|
|
|
static int ath10k_sta_state(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
enum ieee80211_sta_state old_state,
|
|
enum ieee80211_sta_state new_state)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv;
|
|
int ret = 0;
|
|
|
|
if (old_state == IEEE80211_STA_NOTEXIST &&
|
|
new_state == IEEE80211_STA_NONE) {
|
|
memset(arsta, 0, sizeof(*arsta));
|
|
arsta->arvif = arvif;
|
|
INIT_WORK(&arsta->update_wk, ath10k_sta_rc_update_wk);
|
|
}
|
|
|
|
/* cancel must be done outside the mutex to avoid deadlock */
|
|
if ((old_state == IEEE80211_STA_NONE &&
|
|
new_state == IEEE80211_STA_NOTEXIST))
|
|
cancel_work_sync(&arsta->update_wk);
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (old_state == IEEE80211_STA_NOTEXIST &&
|
|
new_state == IEEE80211_STA_NONE) {
|
|
/*
|
|
* New station addition.
|
|
*/
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d peer create %pM (new sta) sta %d / %d peer %d / %d\n",
|
|
arvif->vdev_id, sta->addr,
|
|
ar->num_stations + 1, ar->max_num_stations,
|
|
ar->num_peers + 1, ar->max_num_peers);
|
|
|
|
ret = ath10k_mac_inc_num_stations(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "refusing to associate station: too many connected already (%d)\n",
|
|
ar->max_num_stations);
|
|
goto exit;
|
|
}
|
|
|
|
ret = ath10k_peer_create(ar, arvif->vdev_id, sta->addr);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to add peer %pM for vdev %d when adding a new sta: %i\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
ath10k_mac_dec_num_stations(arvif);
|
|
goto exit;
|
|
}
|
|
|
|
if (vif->type == NL80211_IFTYPE_STATION) {
|
|
WARN_ON(arvif->is_started);
|
|
|
|
ret = ath10k_vdev_start(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to start vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
WARN_ON(ath10k_peer_delete(ar, arvif->vdev_id,
|
|
sta->addr));
|
|
ath10k_mac_dec_num_stations(arvif);
|
|
goto exit;
|
|
}
|
|
|
|
arvif->is_started = true;
|
|
}
|
|
} else if ((old_state == IEEE80211_STA_NONE &&
|
|
new_state == IEEE80211_STA_NOTEXIST)) {
|
|
/*
|
|
* Existing station deletion.
|
|
*/
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac vdev %d peer delete %pM (sta gone)\n",
|
|
arvif->vdev_id, sta->addr);
|
|
|
|
if (vif->type == NL80211_IFTYPE_STATION) {
|
|
WARN_ON(!arvif->is_started);
|
|
|
|
ret = ath10k_vdev_stop(arvif);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to stop vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
|
|
arvif->is_started = false;
|
|
}
|
|
|
|
ret = ath10k_peer_delete(ar, arvif->vdev_id, sta->addr);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to delete peer %pM for vdev %d: %i\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
|
|
ath10k_mac_dec_num_stations(arvif);
|
|
} else if (old_state == IEEE80211_STA_AUTH &&
|
|
new_state == IEEE80211_STA_ASSOC &&
|
|
(vif->type == NL80211_IFTYPE_AP ||
|
|
vif->type == NL80211_IFTYPE_ADHOC)) {
|
|
/*
|
|
* New association.
|
|
*/
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac sta %pM associated\n",
|
|
sta->addr);
|
|
|
|
ret = ath10k_station_assoc(ar, vif, sta, false);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to associate station %pM for vdev %i: %i\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
} else if (old_state == IEEE80211_STA_ASSOC &&
|
|
new_state == IEEE80211_STA_AUTH &&
|
|
(vif->type == NL80211_IFTYPE_AP ||
|
|
vif->type == NL80211_IFTYPE_ADHOC)) {
|
|
/*
|
|
* Disassociation.
|
|
*/
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac sta %pM disassociated\n",
|
|
sta->addr);
|
|
|
|
ret = ath10k_station_disassoc(ar, vif, sta);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to disassociate station: %pM vdev %i: %i\n",
|
|
sta->addr, arvif->vdev_id, ret);
|
|
}
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_conf_tx_uapsd(struct ath10k *ar, struct ieee80211_vif *vif,
|
|
u16 ac, bool enable)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
u32 value = 0;
|
|
int ret = 0;
|
|
|
|
lockdep_assert_held(&ar->conf_mutex);
|
|
|
|
if (arvif->vdev_type != WMI_VDEV_TYPE_STA)
|
|
return 0;
|
|
|
|
switch (ac) {
|
|
case IEEE80211_AC_VO:
|
|
value = WMI_STA_PS_UAPSD_AC3_DELIVERY_EN |
|
|
WMI_STA_PS_UAPSD_AC3_TRIGGER_EN;
|
|
break;
|
|
case IEEE80211_AC_VI:
|
|
value = WMI_STA_PS_UAPSD_AC2_DELIVERY_EN |
|
|
WMI_STA_PS_UAPSD_AC2_TRIGGER_EN;
|
|
break;
|
|
case IEEE80211_AC_BE:
|
|
value = WMI_STA_PS_UAPSD_AC1_DELIVERY_EN |
|
|
WMI_STA_PS_UAPSD_AC1_TRIGGER_EN;
|
|
break;
|
|
case IEEE80211_AC_BK:
|
|
value = WMI_STA_PS_UAPSD_AC0_DELIVERY_EN |
|
|
WMI_STA_PS_UAPSD_AC0_TRIGGER_EN;
|
|
break;
|
|
}
|
|
|
|
if (enable)
|
|
arvif->u.sta.uapsd |= value;
|
|
else
|
|
arvif->u.sta.uapsd &= ~value;
|
|
|
|
ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id,
|
|
WMI_STA_PS_PARAM_UAPSD,
|
|
arvif->u.sta.uapsd);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set uapsd params: %d\n", ret);
|
|
goto exit;
|
|
}
|
|
|
|
if (arvif->u.sta.uapsd)
|
|
value = WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD;
|
|
else
|
|
value = WMI_STA_PS_RX_WAKE_POLICY_WAKE;
|
|
|
|
ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id,
|
|
WMI_STA_PS_PARAM_RX_WAKE_POLICY,
|
|
value);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set rx wake param: %d\n", ret);
|
|
|
|
ret = ath10k_mac_vif_recalc_ps_wake_threshold(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalc ps wake threshold on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ath10k_mac_vif_recalc_ps_poll_count(arvif);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to recalc ps poll count on vdev %i: %d\n",
|
|
arvif->vdev_id, ret);
|
|
return ret;
|
|
}
|
|
|
|
exit:
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_conf_tx(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif, u16 ac,
|
|
const struct ieee80211_tx_queue_params *params)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct wmi_wmm_params_arg *p = NULL;
|
|
int ret;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
switch (ac) {
|
|
case IEEE80211_AC_VO:
|
|
p = &ar->wmm_params.ac_vo;
|
|
break;
|
|
case IEEE80211_AC_VI:
|
|
p = &ar->wmm_params.ac_vi;
|
|
break;
|
|
case IEEE80211_AC_BE:
|
|
p = &ar->wmm_params.ac_be;
|
|
break;
|
|
case IEEE80211_AC_BK:
|
|
p = &ar->wmm_params.ac_bk;
|
|
break;
|
|
}
|
|
|
|
if (WARN_ON(!p)) {
|
|
ret = -EINVAL;
|
|
goto exit;
|
|
}
|
|
|
|
p->cwmin = params->cw_min;
|
|
p->cwmax = params->cw_max;
|
|
p->aifs = params->aifs;
|
|
|
|
/*
|
|
* The channel time duration programmed in the HW is in absolute
|
|
* microseconds, while mac80211 gives the txop in units of
|
|
* 32 microseconds.
|
|
*/
|
|
p->txop = params->txop * 32;
|
|
|
|
/* FIXME: FW accepts wmm params per hw, not per vif */
|
|
ret = ath10k_wmi_pdev_set_wmm_params(ar, &ar->wmm_params);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set wmm params: %d\n", ret);
|
|
goto exit;
|
|
}
|
|
|
|
ret = ath10k_conf_tx_uapsd(ar, vif, ac, params->uapsd);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to set sta uapsd: %d\n", ret);
|
|
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
#define ATH10K_ROC_TIMEOUT_HZ (2*HZ)
|
|
|
|
static int ath10k_remain_on_channel(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_channel *chan,
|
|
int duration,
|
|
enum ieee80211_roc_type type)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct wmi_start_scan_arg arg;
|
|
int ret = 0;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
switch (ar->scan.state) {
|
|
case ATH10K_SCAN_IDLE:
|
|
reinit_completion(&ar->scan.started);
|
|
reinit_completion(&ar->scan.completed);
|
|
reinit_completion(&ar->scan.on_channel);
|
|
ar->scan.state = ATH10K_SCAN_STARTING;
|
|
ar->scan.is_roc = true;
|
|
ar->scan.vdev_id = arvif->vdev_id;
|
|
ar->scan.roc_freq = chan->center_freq;
|
|
ret = 0;
|
|
break;
|
|
case ATH10K_SCAN_STARTING:
|
|
case ATH10K_SCAN_RUNNING:
|
|
case ATH10K_SCAN_ABORTING:
|
|
ret = -EBUSY;
|
|
break;
|
|
}
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
if (ret)
|
|
goto exit;
|
|
|
|
duration = max(duration, WMI_SCAN_CHAN_MIN_TIME_MSEC);
|
|
|
|
memset(&arg, 0, sizeof(arg));
|
|
ath10k_wmi_start_scan_init(ar, &arg);
|
|
arg.vdev_id = arvif->vdev_id;
|
|
arg.scan_id = ATH10K_SCAN_ID;
|
|
arg.n_channels = 1;
|
|
arg.channels[0] = chan->center_freq;
|
|
arg.dwell_time_active = duration;
|
|
arg.dwell_time_passive = duration;
|
|
arg.max_scan_time = 2 * duration;
|
|
arg.scan_ctrl_flags |= WMI_SCAN_FLAG_PASSIVE;
|
|
arg.scan_ctrl_flags |= WMI_SCAN_FILTER_PROBE_REQ;
|
|
|
|
ret = ath10k_start_scan(ar, &arg);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to start roc scan: %d\n", ret);
|
|
spin_lock_bh(&ar->data_lock);
|
|
ar->scan.state = ATH10K_SCAN_IDLE;
|
|
spin_unlock_bh(&ar->data_lock);
|
|
goto exit;
|
|
}
|
|
|
|
ret = wait_for_completion_timeout(&ar->scan.on_channel, 3*HZ);
|
|
if (ret == 0) {
|
|
ath10k_warn(ar, "failed to switch to channel for roc scan\n");
|
|
|
|
ret = ath10k_scan_stop(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to stop scan: %d\n", ret);
|
|
|
|
ret = -ETIMEDOUT;
|
|
goto exit;
|
|
}
|
|
|
|
ret = 0;
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_cancel_remain_on_channel(struct ieee80211_hw *hw)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
ath10k_scan_abort(ar);
|
|
mutex_unlock(&ar->conf_mutex);
|
|
|
|
cancel_delayed_work_sync(&ar->scan.timeout);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Both RTS and Fragmentation threshold are interface-specific
|
|
* in ath10k, but device-specific in mac80211.
|
|
*/
|
|
|
|
static int ath10k_set_rts_threshold(struct ieee80211_hw *hw, u32 value)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif;
|
|
int ret = 0;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
list_for_each_entry(arvif, &ar->arvifs, list) {
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d rts threshold %d\n",
|
|
arvif->vdev_id, value);
|
|
|
|
ret = ath10k_mac_set_rts(arvif, value);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set rts threshold for vdev %d: %d\n",
|
|
arvif->vdev_id, ret);
|
|
break;
|
|
}
|
|
}
|
|
mutex_unlock(&ar->conf_mutex);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void ath10k_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
|
|
u32 queues, bool drop)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
bool skip;
|
|
int ret;
|
|
|
|
/* mac80211 doesn't care if we really xmit queued frames or not
|
|
* we'll collect those frames either way if we stop/delete vdevs */
|
|
if (drop)
|
|
return;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (ar->state == ATH10K_STATE_WEDGED)
|
|
goto skip;
|
|
|
|
ret = wait_event_timeout(ar->htt.empty_tx_wq, ({
|
|
bool empty;
|
|
|
|
spin_lock_bh(&ar->htt.tx_lock);
|
|
empty = (ar->htt.num_pending_tx == 0);
|
|
spin_unlock_bh(&ar->htt.tx_lock);
|
|
|
|
skip = (ar->state == ATH10K_STATE_WEDGED) ||
|
|
test_bit(ATH10K_FLAG_CRASH_FLUSH,
|
|
&ar->dev_flags);
|
|
|
|
(empty || skip);
|
|
}), ATH10K_FLUSH_TIMEOUT_HZ);
|
|
|
|
if (ret <= 0 || skip)
|
|
ath10k_warn(ar, "failed to flush transmit queue (skip %i ar-state %i): %i\n",
|
|
skip, ar->state, ret);
|
|
|
|
skip:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
/* TODO: Implement this function properly
|
|
* For now it is needed to reply to Probe Requests in IBSS mode.
|
|
* Propably we need this information from FW.
|
|
*/
|
|
static int ath10k_tx_last_beacon(struct ieee80211_hw *hw)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int ath10k_suspend(struct ieee80211_hw *hw,
|
|
struct cfg80211_wowlan *wowlan)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
int ret;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
ret = ath10k_wait_for_suspend(ar, WMI_PDEV_SUSPEND);
|
|
if (ret) {
|
|
if (ret == -ETIMEDOUT)
|
|
goto resume;
|
|
ret = 1;
|
|
goto exit;
|
|
}
|
|
|
|
ret = ath10k_hif_suspend(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to suspend hif: %d\n", ret);
|
|
goto resume;
|
|
}
|
|
|
|
ret = 0;
|
|
goto exit;
|
|
resume:
|
|
ret = ath10k_wmi_pdev_resume_target(ar);
|
|
if (ret)
|
|
ath10k_warn(ar, "failed to resume target: %d\n", ret);
|
|
|
|
ret = 1;
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_resume(struct ieee80211_hw *hw)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
int ret;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
ret = ath10k_hif_resume(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to resume hif: %d\n", ret);
|
|
ret = 1;
|
|
goto exit;
|
|
}
|
|
|
|
ret = ath10k_wmi_pdev_resume_target(ar);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to resume target: %d\n", ret);
|
|
ret = 1;
|
|
goto exit;
|
|
}
|
|
|
|
ret = 0;
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
#endif
|
|
|
|
static void ath10k_reconfig_complete(struct ieee80211_hw *hw,
|
|
enum ieee80211_reconfig_type reconfig_type)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
|
|
if (reconfig_type != IEEE80211_RECONFIG_TYPE_RESTART)
|
|
return;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
/* If device failed to restart it will be in a different state, e.g.
|
|
* ATH10K_STATE_WEDGED */
|
|
if (ar->state == ATH10K_STATE_RESTARTED) {
|
|
ath10k_info(ar, "device successfully recovered\n");
|
|
ar->state = ATH10K_STATE_ON;
|
|
ieee80211_wake_queues(ar->hw);
|
|
}
|
|
|
|
mutex_unlock(&ar->conf_mutex);
|
|
}
|
|
|
|
static int ath10k_get_survey(struct ieee80211_hw *hw, int idx,
|
|
struct survey_info *survey)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ieee80211_supported_band *sband;
|
|
struct survey_info *ar_survey = &ar->survey[idx];
|
|
int ret = 0;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
sband = hw->wiphy->bands[IEEE80211_BAND_2GHZ];
|
|
if (sband && idx >= sband->n_channels) {
|
|
idx -= sband->n_channels;
|
|
sband = NULL;
|
|
}
|
|
|
|
if (!sband)
|
|
sband = hw->wiphy->bands[IEEE80211_BAND_5GHZ];
|
|
|
|
if (!sband || idx >= sband->n_channels) {
|
|
ret = -ENOENT;
|
|
goto exit;
|
|
}
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
memcpy(survey, ar_survey, sizeof(*survey));
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
survey->channel = &sband->channels[idx];
|
|
|
|
if (ar->rx_channel == survey->channel)
|
|
survey->filled |= SURVEY_INFO_IN_USE;
|
|
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
/* Helper table for legacy fixed_rate/bitrate_mask */
|
|
static const u8 cck_ofdm_rate[] = {
|
|
/* CCK */
|
|
3, /* 1Mbps */
|
|
2, /* 2Mbps */
|
|
1, /* 5.5Mbps */
|
|
0, /* 11Mbps */
|
|
/* OFDM */
|
|
3, /* 6Mbps */
|
|
7, /* 9Mbps */
|
|
2, /* 12Mbps */
|
|
6, /* 18Mbps */
|
|
1, /* 24Mbps */
|
|
5, /* 36Mbps */
|
|
0, /* 48Mbps */
|
|
4, /* 54Mbps */
|
|
};
|
|
|
|
/* Check if only one bit set */
|
|
static int ath10k_check_single_mask(u32 mask)
|
|
{
|
|
int bit;
|
|
|
|
bit = ffs(mask);
|
|
if (!bit)
|
|
return 0;
|
|
|
|
mask &= ~BIT(bit - 1);
|
|
if (mask)
|
|
return 2;
|
|
|
|
return 1;
|
|
}
|
|
|
|
static bool
|
|
ath10k_default_bitrate_mask(struct ath10k *ar,
|
|
enum ieee80211_band band,
|
|
const struct cfg80211_bitrate_mask *mask)
|
|
{
|
|
u32 legacy = 0x00ff;
|
|
u8 ht = 0xff, i;
|
|
u16 vht = 0x3ff;
|
|
u16 nrf = ar->num_rf_chains;
|
|
|
|
if (ar->cfg_tx_chainmask)
|
|
nrf = get_nss_from_chainmask(ar->cfg_tx_chainmask);
|
|
|
|
switch (band) {
|
|
case IEEE80211_BAND_2GHZ:
|
|
legacy = 0x00fff;
|
|
vht = 0;
|
|
break;
|
|
case IEEE80211_BAND_5GHZ:
|
|
break;
|
|
default:
|
|
return false;
|
|
}
|
|
|
|
if (mask->control[band].legacy != legacy)
|
|
return false;
|
|
|
|
for (i = 0; i < nrf; i++)
|
|
if (mask->control[band].ht_mcs[i] != ht)
|
|
return false;
|
|
|
|
for (i = 0; i < nrf; i++)
|
|
if (mask->control[band].vht_mcs[i] != vht)
|
|
return false;
|
|
|
|
return true;
|
|
}
|
|
|
|
static bool
|
|
ath10k_bitrate_mask_nss(const struct cfg80211_bitrate_mask *mask,
|
|
enum ieee80211_band band,
|
|
u8 *fixed_nss)
|
|
{
|
|
int ht_nss = 0, vht_nss = 0, i;
|
|
|
|
/* check legacy */
|
|
if (ath10k_check_single_mask(mask->control[band].legacy))
|
|
return false;
|
|
|
|
/* check HT */
|
|
for (i = 0; i < IEEE80211_HT_MCS_MASK_LEN; i++) {
|
|
if (mask->control[band].ht_mcs[i] == 0xff)
|
|
continue;
|
|
else if (mask->control[band].ht_mcs[i] == 0x00)
|
|
break;
|
|
|
|
return false;
|
|
}
|
|
|
|
ht_nss = i;
|
|
|
|
/* check VHT */
|
|
for (i = 0; i < NL80211_VHT_NSS_MAX; i++) {
|
|
if (mask->control[band].vht_mcs[i] == 0x03ff)
|
|
continue;
|
|
else if (mask->control[band].vht_mcs[i] == 0x0000)
|
|
break;
|
|
|
|
return false;
|
|
}
|
|
|
|
vht_nss = i;
|
|
|
|
if (ht_nss > 0 && vht_nss > 0)
|
|
return false;
|
|
|
|
if (ht_nss)
|
|
*fixed_nss = ht_nss;
|
|
else if (vht_nss)
|
|
*fixed_nss = vht_nss;
|
|
else
|
|
return false;
|
|
|
|
return true;
|
|
}
|
|
|
|
static bool
|
|
ath10k_bitrate_mask_correct(const struct cfg80211_bitrate_mask *mask,
|
|
enum ieee80211_band band,
|
|
enum wmi_rate_preamble *preamble)
|
|
{
|
|
int legacy = 0, ht = 0, vht = 0, i;
|
|
|
|
*preamble = WMI_RATE_PREAMBLE_OFDM;
|
|
|
|
/* check legacy */
|
|
legacy = ath10k_check_single_mask(mask->control[band].legacy);
|
|
if (legacy > 1)
|
|
return false;
|
|
|
|
/* check HT */
|
|
for (i = 0; i < IEEE80211_HT_MCS_MASK_LEN; i++)
|
|
ht += ath10k_check_single_mask(mask->control[band].ht_mcs[i]);
|
|
if (ht > 1)
|
|
return false;
|
|
|
|
/* check VHT */
|
|
for (i = 0; i < NL80211_VHT_NSS_MAX; i++)
|
|
vht += ath10k_check_single_mask(mask->control[band].vht_mcs[i]);
|
|
if (vht > 1)
|
|
return false;
|
|
|
|
/* Currently we support only one fixed_rate */
|
|
if ((legacy + ht + vht) != 1)
|
|
return false;
|
|
|
|
if (ht)
|
|
*preamble = WMI_RATE_PREAMBLE_HT;
|
|
else if (vht)
|
|
*preamble = WMI_RATE_PREAMBLE_VHT;
|
|
|
|
return true;
|
|
}
|
|
|
|
static bool
|
|
ath10k_bitrate_mask_rate(struct ath10k *ar,
|
|
const struct cfg80211_bitrate_mask *mask,
|
|
enum ieee80211_band band,
|
|
u8 *fixed_rate,
|
|
u8 *fixed_nss)
|
|
{
|
|
u8 rate = 0, pream = 0, nss = 0, i;
|
|
enum wmi_rate_preamble preamble;
|
|
|
|
/* Check if single rate correct */
|
|
if (!ath10k_bitrate_mask_correct(mask, band, &preamble))
|
|
return false;
|
|
|
|
pream = preamble;
|
|
|
|
switch (preamble) {
|
|
case WMI_RATE_PREAMBLE_CCK:
|
|
case WMI_RATE_PREAMBLE_OFDM:
|
|
i = ffs(mask->control[band].legacy) - 1;
|
|
|
|
if (band == IEEE80211_BAND_2GHZ && i < 4)
|
|
pream = WMI_RATE_PREAMBLE_CCK;
|
|
|
|
if (band == IEEE80211_BAND_5GHZ)
|
|
i += 4;
|
|
|
|
if (i >= ARRAY_SIZE(cck_ofdm_rate))
|
|
return false;
|
|
|
|
rate = cck_ofdm_rate[i];
|
|
break;
|
|
case WMI_RATE_PREAMBLE_HT:
|
|
for (i = 0; i < IEEE80211_HT_MCS_MASK_LEN; i++)
|
|
if (mask->control[band].ht_mcs[i])
|
|
break;
|
|
|
|
if (i == IEEE80211_HT_MCS_MASK_LEN)
|
|
return false;
|
|
|
|
rate = ffs(mask->control[band].ht_mcs[i]) - 1;
|
|
nss = i;
|
|
break;
|
|
case WMI_RATE_PREAMBLE_VHT:
|
|
for (i = 0; i < NL80211_VHT_NSS_MAX; i++)
|
|
if (mask->control[band].vht_mcs[i])
|
|
break;
|
|
|
|
if (i == NL80211_VHT_NSS_MAX)
|
|
return false;
|
|
|
|
rate = ffs(mask->control[band].vht_mcs[i]) - 1;
|
|
nss = i;
|
|
break;
|
|
}
|
|
|
|
*fixed_nss = nss + 1;
|
|
nss <<= 4;
|
|
pream <<= 6;
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac fixed rate pream 0x%02x nss 0x%02x rate 0x%02x\n",
|
|
pream, nss, rate);
|
|
|
|
*fixed_rate = pream | nss | rate;
|
|
|
|
return true;
|
|
}
|
|
|
|
static bool ath10k_get_fixed_rate_nss(struct ath10k *ar,
|
|
const struct cfg80211_bitrate_mask *mask,
|
|
enum ieee80211_band band,
|
|
u8 *fixed_rate,
|
|
u8 *fixed_nss)
|
|
{
|
|
/* First check full NSS mask, if we can simply limit NSS */
|
|
if (ath10k_bitrate_mask_nss(mask, band, fixed_nss))
|
|
return true;
|
|
|
|
/* Next Check single rate is set */
|
|
return ath10k_bitrate_mask_rate(ar, mask, band, fixed_rate, fixed_nss);
|
|
}
|
|
|
|
static int ath10k_set_fixed_rate_param(struct ath10k_vif *arvif,
|
|
u8 fixed_rate,
|
|
u8 fixed_nss,
|
|
u8 force_sgi)
|
|
{
|
|
struct ath10k *ar = arvif->ar;
|
|
u32 vdev_param;
|
|
int ret = 0;
|
|
|
|
mutex_lock(&ar->conf_mutex);
|
|
|
|
if (arvif->fixed_rate == fixed_rate &&
|
|
arvif->fixed_nss == fixed_nss &&
|
|
arvif->force_sgi == force_sgi)
|
|
goto exit;
|
|
|
|
if (fixed_rate == WMI_FIXED_RATE_NONE)
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac disable fixed bitrate mask\n");
|
|
|
|
if (force_sgi)
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac force sgi\n");
|
|
|
|
vdev_param = ar->wmi.vdev_param->fixed_rate;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id,
|
|
vdev_param, fixed_rate);
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set fixed rate param 0x%02x: %d\n",
|
|
fixed_rate, ret);
|
|
ret = -EINVAL;
|
|
goto exit;
|
|
}
|
|
|
|
arvif->fixed_rate = fixed_rate;
|
|
|
|
vdev_param = ar->wmi.vdev_param->nss;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id,
|
|
vdev_param, fixed_nss);
|
|
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set fixed nss param %d: %d\n",
|
|
fixed_nss, ret);
|
|
ret = -EINVAL;
|
|
goto exit;
|
|
}
|
|
|
|
arvif->fixed_nss = fixed_nss;
|
|
|
|
vdev_param = ar->wmi.vdev_param->sgi;
|
|
ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param,
|
|
force_sgi);
|
|
|
|
if (ret) {
|
|
ath10k_warn(ar, "failed to set sgi param %d: %d\n",
|
|
force_sgi, ret);
|
|
ret = -EINVAL;
|
|
goto exit;
|
|
}
|
|
|
|
arvif->force_sgi = force_sgi;
|
|
|
|
exit:
|
|
mutex_unlock(&ar->conf_mutex);
|
|
return ret;
|
|
}
|
|
|
|
static int ath10k_set_bitrate_mask(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
const struct cfg80211_bitrate_mask *mask)
|
|
{
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
struct ath10k *ar = arvif->ar;
|
|
enum ieee80211_band band = ar->hw->conf.chandef.chan->band;
|
|
u8 fixed_rate = WMI_FIXED_RATE_NONE;
|
|
u8 fixed_nss = ar->num_rf_chains;
|
|
u8 force_sgi;
|
|
|
|
if (ar->cfg_tx_chainmask)
|
|
fixed_nss = get_nss_from_chainmask(ar->cfg_tx_chainmask);
|
|
|
|
force_sgi = mask->control[band].gi;
|
|
if (force_sgi == NL80211_TXRATE_FORCE_LGI)
|
|
return -EINVAL;
|
|
|
|
if (!ath10k_default_bitrate_mask(ar, band, mask)) {
|
|
if (!ath10k_get_fixed_rate_nss(ar, mask, band,
|
|
&fixed_rate,
|
|
&fixed_nss))
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (fixed_rate == WMI_FIXED_RATE_NONE && force_sgi) {
|
|
ath10k_warn(ar, "failed to force SGI usage for default rate settings\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
return ath10k_set_fixed_rate_param(arvif, fixed_rate,
|
|
fixed_nss, force_sgi);
|
|
}
|
|
|
|
static void ath10k_sta_rc_update(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
struct ieee80211_sta *sta,
|
|
u32 changed)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv;
|
|
u32 bw, smps;
|
|
|
|
spin_lock_bh(&ar->data_lock);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC,
|
|
"mac sta rc update for %pM changed %08x bw %d nss %d smps %d\n",
|
|
sta->addr, changed, sta->bandwidth, sta->rx_nss,
|
|
sta->smps_mode);
|
|
|
|
if (changed & IEEE80211_RC_BW_CHANGED) {
|
|
bw = WMI_PEER_CHWIDTH_20MHZ;
|
|
|
|
switch (sta->bandwidth) {
|
|
case IEEE80211_STA_RX_BW_20:
|
|
bw = WMI_PEER_CHWIDTH_20MHZ;
|
|
break;
|
|
case IEEE80211_STA_RX_BW_40:
|
|
bw = WMI_PEER_CHWIDTH_40MHZ;
|
|
break;
|
|
case IEEE80211_STA_RX_BW_80:
|
|
bw = WMI_PEER_CHWIDTH_80MHZ;
|
|
break;
|
|
case IEEE80211_STA_RX_BW_160:
|
|
ath10k_warn(ar, "Invalid bandwith %d in rc update for %pM\n",
|
|
sta->bandwidth, sta->addr);
|
|
bw = WMI_PEER_CHWIDTH_20MHZ;
|
|
break;
|
|
}
|
|
|
|
arsta->bw = bw;
|
|
}
|
|
|
|
if (changed & IEEE80211_RC_NSS_CHANGED)
|
|
arsta->nss = sta->rx_nss;
|
|
|
|
if (changed & IEEE80211_RC_SMPS_CHANGED) {
|
|
smps = WMI_PEER_SMPS_PS_NONE;
|
|
|
|
switch (sta->smps_mode) {
|
|
case IEEE80211_SMPS_AUTOMATIC:
|
|
case IEEE80211_SMPS_OFF:
|
|
smps = WMI_PEER_SMPS_PS_NONE;
|
|
break;
|
|
case IEEE80211_SMPS_STATIC:
|
|
smps = WMI_PEER_SMPS_STATIC;
|
|
break;
|
|
case IEEE80211_SMPS_DYNAMIC:
|
|
smps = WMI_PEER_SMPS_DYNAMIC;
|
|
break;
|
|
case IEEE80211_SMPS_NUM_MODES:
|
|
ath10k_warn(ar, "Invalid smps %d in sta rc update for %pM\n",
|
|
sta->smps_mode, sta->addr);
|
|
smps = WMI_PEER_SMPS_PS_NONE;
|
|
break;
|
|
}
|
|
|
|
arsta->smps = smps;
|
|
}
|
|
|
|
arsta->changed |= changed;
|
|
|
|
spin_unlock_bh(&ar->data_lock);
|
|
|
|
ieee80211_queue_work(hw, &arsta->update_wk);
|
|
}
|
|
|
|
static u64 ath10k_get_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif)
|
|
{
|
|
/*
|
|
* FIXME: Return 0 for time being. Need to figure out whether FW
|
|
* has the API to fetch 64-bit local TSF
|
|
*/
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ath10k_ampdu_action(struct ieee80211_hw *hw,
|
|
struct ieee80211_vif *vif,
|
|
enum ieee80211_ampdu_mlme_action action,
|
|
struct ieee80211_sta *sta, u16 tid, u16 *ssn,
|
|
u8 buf_size)
|
|
{
|
|
struct ath10k *ar = hw->priv;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
|
|
ath10k_dbg(ar, ATH10K_DBG_MAC, "mac ampdu vdev_id %i sta %pM tid %hu action %d\n",
|
|
arvif->vdev_id, sta->addr, tid, action);
|
|
|
|
switch (action) {
|
|
case IEEE80211_AMPDU_RX_START:
|
|
case IEEE80211_AMPDU_RX_STOP:
|
|
/* HTT AddBa/DelBa events trigger mac80211 Rx BA session
|
|
* creation/removal. Do we need to verify this?
|
|
*/
|
|
return 0;
|
|
case IEEE80211_AMPDU_TX_START:
|
|
case IEEE80211_AMPDU_TX_STOP_CONT:
|
|
case IEEE80211_AMPDU_TX_STOP_FLUSH:
|
|
case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT:
|
|
case IEEE80211_AMPDU_TX_OPERATIONAL:
|
|
/* Firmware offloads Tx aggregation entirely so deny mac80211
|
|
* Tx aggregation requests.
|
|
*/
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static const struct ieee80211_ops ath10k_ops = {
|
|
.tx = ath10k_tx,
|
|
.start = ath10k_start,
|
|
.stop = ath10k_stop,
|
|
.config = ath10k_config,
|
|
.add_interface = ath10k_add_interface,
|
|
.remove_interface = ath10k_remove_interface,
|
|
.configure_filter = ath10k_configure_filter,
|
|
.bss_info_changed = ath10k_bss_info_changed,
|
|
.hw_scan = ath10k_hw_scan,
|
|
.cancel_hw_scan = ath10k_cancel_hw_scan,
|
|
.set_key = ath10k_set_key,
|
|
.sta_state = ath10k_sta_state,
|
|
.conf_tx = ath10k_conf_tx,
|
|
.remain_on_channel = ath10k_remain_on_channel,
|
|
.cancel_remain_on_channel = ath10k_cancel_remain_on_channel,
|
|
.set_rts_threshold = ath10k_set_rts_threshold,
|
|
.flush = ath10k_flush,
|
|
.tx_last_beacon = ath10k_tx_last_beacon,
|
|
.set_antenna = ath10k_set_antenna,
|
|
.get_antenna = ath10k_get_antenna,
|
|
.reconfig_complete = ath10k_reconfig_complete,
|
|
.get_survey = ath10k_get_survey,
|
|
.set_bitrate_mask = ath10k_set_bitrate_mask,
|
|
.sta_rc_update = ath10k_sta_rc_update,
|
|
.get_tsf = ath10k_get_tsf,
|
|
.ampdu_action = ath10k_ampdu_action,
|
|
.get_et_sset_count = ath10k_debug_get_et_sset_count,
|
|
.get_et_stats = ath10k_debug_get_et_stats,
|
|
.get_et_strings = ath10k_debug_get_et_strings,
|
|
|
|
CFG80211_TESTMODE_CMD(ath10k_tm_cmd)
|
|
|
|
#ifdef CONFIG_PM
|
|
.suspend = ath10k_suspend,
|
|
.resume = ath10k_resume,
|
|
#endif
|
|
};
|
|
|
|
#define RATETAB_ENT(_rate, _rateid, _flags) { \
|
|
.bitrate = (_rate), \
|
|
.flags = (_flags), \
|
|
.hw_value = (_rateid), \
|
|
}
|
|
|
|
#define CHAN2G(_channel, _freq, _flags) { \
|
|
.band = IEEE80211_BAND_2GHZ, \
|
|
.hw_value = (_channel), \
|
|
.center_freq = (_freq), \
|
|
.flags = (_flags), \
|
|
.max_antenna_gain = 0, \
|
|
.max_power = 30, \
|
|
}
|
|
|
|
#define CHAN5G(_channel, _freq, _flags) { \
|
|
.band = IEEE80211_BAND_5GHZ, \
|
|
.hw_value = (_channel), \
|
|
.center_freq = (_freq), \
|
|
.flags = (_flags), \
|
|
.max_antenna_gain = 0, \
|
|
.max_power = 30, \
|
|
}
|
|
|
|
static const struct ieee80211_channel ath10k_2ghz_channels[] = {
|
|
CHAN2G(1, 2412, 0),
|
|
CHAN2G(2, 2417, 0),
|
|
CHAN2G(3, 2422, 0),
|
|
CHAN2G(4, 2427, 0),
|
|
CHAN2G(5, 2432, 0),
|
|
CHAN2G(6, 2437, 0),
|
|
CHAN2G(7, 2442, 0),
|
|
CHAN2G(8, 2447, 0),
|
|
CHAN2G(9, 2452, 0),
|
|
CHAN2G(10, 2457, 0),
|
|
CHAN2G(11, 2462, 0),
|
|
CHAN2G(12, 2467, 0),
|
|
CHAN2G(13, 2472, 0),
|
|
CHAN2G(14, 2484, 0),
|
|
};
|
|
|
|
static const struct ieee80211_channel ath10k_5ghz_channels[] = {
|
|
CHAN5G(36, 5180, 0),
|
|
CHAN5G(40, 5200, 0),
|
|
CHAN5G(44, 5220, 0),
|
|
CHAN5G(48, 5240, 0),
|
|
CHAN5G(52, 5260, 0),
|
|
CHAN5G(56, 5280, 0),
|
|
CHAN5G(60, 5300, 0),
|
|
CHAN5G(64, 5320, 0),
|
|
CHAN5G(100, 5500, 0),
|
|
CHAN5G(104, 5520, 0),
|
|
CHAN5G(108, 5540, 0),
|
|
CHAN5G(112, 5560, 0),
|
|
CHAN5G(116, 5580, 0),
|
|
CHAN5G(120, 5600, 0),
|
|
CHAN5G(124, 5620, 0),
|
|
CHAN5G(128, 5640, 0),
|
|
CHAN5G(132, 5660, 0),
|
|
CHAN5G(136, 5680, 0),
|
|
CHAN5G(140, 5700, 0),
|
|
CHAN5G(149, 5745, 0),
|
|
CHAN5G(153, 5765, 0),
|
|
CHAN5G(157, 5785, 0),
|
|
CHAN5G(161, 5805, 0),
|
|
CHAN5G(165, 5825, 0),
|
|
};
|
|
|
|
/* Note: Be careful if you re-order these. There is code which depends on this
|
|
* ordering.
|
|
*/
|
|
static struct ieee80211_rate ath10k_rates[] = {
|
|
/* CCK */
|
|
RATETAB_ENT(10, 0x82, 0),
|
|
RATETAB_ENT(20, 0x84, 0),
|
|
RATETAB_ENT(55, 0x8b, 0),
|
|
RATETAB_ENT(110, 0x96, 0),
|
|
/* OFDM */
|
|
RATETAB_ENT(60, 0x0c, 0),
|
|
RATETAB_ENT(90, 0x12, 0),
|
|
RATETAB_ENT(120, 0x18, 0),
|
|
RATETAB_ENT(180, 0x24, 0),
|
|
RATETAB_ENT(240, 0x30, 0),
|
|
RATETAB_ENT(360, 0x48, 0),
|
|
RATETAB_ENT(480, 0x60, 0),
|
|
RATETAB_ENT(540, 0x6c, 0),
|
|
};
|
|
|
|
#define ath10k_a_rates (ath10k_rates + 4)
|
|
#define ath10k_a_rates_size (ARRAY_SIZE(ath10k_rates) - 4)
|
|
#define ath10k_g_rates (ath10k_rates + 0)
|
|
#define ath10k_g_rates_size (ARRAY_SIZE(ath10k_rates))
|
|
|
|
struct ath10k *ath10k_mac_create(size_t priv_size)
|
|
{
|
|
struct ieee80211_hw *hw;
|
|
struct ath10k *ar;
|
|
|
|
hw = ieee80211_alloc_hw(sizeof(struct ath10k) + priv_size, &ath10k_ops);
|
|
if (!hw)
|
|
return NULL;
|
|
|
|
ar = hw->priv;
|
|
ar->hw = hw;
|
|
|
|
return ar;
|
|
}
|
|
|
|
void ath10k_mac_destroy(struct ath10k *ar)
|
|
{
|
|
ieee80211_free_hw(ar->hw);
|
|
}
|
|
|
|
static const struct ieee80211_iface_limit ath10k_if_limits[] = {
|
|
{
|
|
.max = 8,
|
|
.types = BIT(NL80211_IFTYPE_STATION)
|
|
| BIT(NL80211_IFTYPE_P2P_CLIENT)
|
|
},
|
|
{
|
|
.max = 3,
|
|
.types = BIT(NL80211_IFTYPE_P2P_GO)
|
|
},
|
|
{
|
|
.max = 1,
|
|
.types = BIT(NL80211_IFTYPE_P2P_DEVICE)
|
|
},
|
|
{
|
|
.max = 7,
|
|
.types = BIT(NL80211_IFTYPE_AP)
|
|
},
|
|
};
|
|
|
|
static const struct ieee80211_iface_limit ath10k_10x_if_limits[] = {
|
|
{
|
|
.max = 8,
|
|
.types = BIT(NL80211_IFTYPE_AP)
|
|
},
|
|
};
|
|
|
|
static const struct ieee80211_iface_combination ath10k_if_comb[] = {
|
|
{
|
|
.limits = ath10k_if_limits,
|
|
.n_limits = ARRAY_SIZE(ath10k_if_limits),
|
|
.max_interfaces = 8,
|
|
.num_different_channels = 1,
|
|
.beacon_int_infra_match = true,
|
|
},
|
|
};
|
|
|
|
static const struct ieee80211_iface_combination ath10k_10x_if_comb[] = {
|
|
{
|
|
.limits = ath10k_10x_if_limits,
|
|
.n_limits = ARRAY_SIZE(ath10k_10x_if_limits),
|
|
.max_interfaces = 8,
|
|
.num_different_channels = 1,
|
|
.beacon_int_infra_match = true,
|
|
#ifdef CONFIG_ATH10K_DFS_CERTIFIED
|
|
.radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
|
|
BIT(NL80211_CHAN_WIDTH_20) |
|
|
BIT(NL80211_CHAN_WIDTH_40) |
|
|
BIT(NL80211_CHAN_WIDTH_80),
|
|
#endif
|
|
},
|
|
};
|
|
|
|
static struct ieee80211_sta_vht_cap ath10k_create_vht_cap(struct ath10k *ar)
|
|
{
|
|
struct ieee80211_sta_vht_cap vht_cap = {0};
|
|
u16 mcs_map;
|
|
int i;
|
|
|
|
vht_cap.vht_supported = 1;
|
|
vht_cap.cap = ar->vht_cap_info;
|
|
|
|
mcs_map = 0;
|
|
for (i = 0; i < 8; i++) {
|
|
if (i < ar->num_rf_chains)
|
|
mcs_map |= IEEE80211_VHT_MCS_SUPPORT_0_9 << (i*2);
|
|
else
|
|
mcs_map |= IEEE80211_VHT_MCS_NOT_SUPPORTED << (i*2);
|
|
}
|
|
|
|
vht_cap.vht_mcs.rx_mcs_map = cpu_to_le16(mcs_map);
|
|
vht_cap.vht_mcs.tx_mcs_map = cpu_to_le16(mcs_map);
|
|
|
|
return vht_cap;
|
|
}
|
|
|
|
static struct ieee80211_sta_ht_cap ath10k_get_ht_cap(struct ath10k *ar)
|
|
{
|
|
int i;
|
|
struct ieee80211_sta_ht_cap ht_cap = {0};
|
|
|
|
if (!(ar->ht_cap_info & WMI_HT_CAP_ENABLED))
|
|
return ht_cap;
|
|
|
|
ht_cap.ht_supported = 1;
|
|
ht_cap.ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K;
|
|
ht_cap.ampdu_density = IEEE80211_HT_MPDU_DENSITY_8;
|
|
ht_cap.cap |= IEEE80211_HT_CAP_SUP_WIDTH_20_40;
|
|
ht_cap.cap |= IEEE80211_HT_CAP_DSSSCCK40;
|
|
ht_cap.cap |= WLAN_HT_CAP_SM_PS_STATIC << IEEE80211_HT_CAP_SM_PS_SHIFT;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_HT20_SGI)
|
|
ht_cap.cap |= IEEE80211_HT_CAP_SGI_20;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_HT40_SGI)
|
|
ht_cap.cap |= IEEE80211_HT_CAP_SGI_40;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_DYNAMIC_SMPS) {
|
|
u32 smps;
|
|
|
|
smps = WLAN_HT_CAP_SM_PS_DYNAMIC;
|
|
smps <<= IEEE80211_HT_CAP_SM_PS_SHIFT;
|
|
|
|
ht_cap.cap |= smps;
|
|
}
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_TX_STBC)
|
|
ht_cap.cap |= IEEE80211_HT_CAP_TX_STBC;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_RX_STBC) {
|
|
u32 stbc;
|
|
|
|
stbc = ar->ht_cap_info;
|
|
stbc &= WMI_HT_CAP_RX_STBC;
|
|
stbc >>= WMI_HT_CAP_RX_STBC_MASK_SHIFT;
|
|
stbc <<= IEEE80211_HT_CAP_RX_STBC_SHIFT;
|
|
stbc &= IEEE80211_HT_CAP_RX_STBC;
|
|
|
|
ht_cap.cap |= stbc;
|
|
}
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_LDPC)
|
|
ht_cap.cap |= IEEE80211_HT_CAP_LDPC_CODING;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_L_SIG_TXOP_PROT)
|
|
ht_cap.cap |= IEEE80211_HT_CAP_LSIG_TXOP_PROT;
|
|
|
|
/* max AMSDU is implicitly taken from vht_cap_info */
|
|
if (ar->vht_cap_info & WMI_VHT_CAP_MAX_MPDU_LEN_MASK)
|
|
ht_cap.cap |= IEEE80211_HT_CAP_MAX_AMSDU;
|
|
|
|
for (i = 0; i < ar->num_rf_chains; i++)
|
|
ht_cap.mcs.rx_mask[i] = 0xFF;
|
|
|
|
ht_cap.mcs.tx_params |= IEEE80211_HT_MCS_TX_DEFINED;
|
|
|
|
return ht_cap;
|
|
}
|
|
|
|
static void ath10k_get_arvif_iter(void *data, u8 *mac,
|
|
struct ieee80211_vif *vif)
|
|
{
|
|
struct ath10k_vif_iter *arvif_iter = data;
|
|
struct ath10k_vif *arvif = ath10k_vif_to_arvif(vif);
|
|
|
|
if (arvif->vdev_id == arvif_iter->vdev_id)
|
|
arvif_iter->arvif = arvif;
|
|
}
|
|
|
|
struct ath10k_vif *ath10k_get_arvif(struct ath10k *ar, u32 vdev_id)
|
|
{
|
|
struct ath10k_vif_iter arvif_iter;
|
|
u32 flags;
|
|
|
|
memset(&arvif_iter, 0, sizeof(struct ath10k_vif_iter));
|
|
arvif_iter.vdev_id = vdev_id;
|
|
|
|
flags = IEEE80211_IFACE_ITER_RESUME_ALL;
|
|
ieee80211_iterate_active_interfaces_atomic(ar->hw,
|
|
flags,
|
|
ath10k_get_arvif_iter,
|
|
&arvif_iter);
|
|
if (!arvif_iter.arvif) {
|
|
ath10k_warn(ar, "No VIF found for vdev %d\n", vdev_id);
|
|
return NULL;
|
|
}
|
|
|
|
return arvif_iter.arvif;
|
|
}
|
|
|
|
int ath10k_mac_register(struct ath10k *ar)
|
|
{
|
|
struct ieee80211_supported_band *band;
|
|
struct ieee80211_sta_vht_cap vht_cap;
|
|
struct ieee80211_sta_ht_cap ht_cap;
|
|
void *channels;
|
|
int ret;
|
|
|
|
SET_IEEE80211_PERM_ADDR(ar->hw, ar->mac_addr);
|
|
|
|
SET_IEEE80211_DEV(ar->hw, ar->dev);
|
|
|
|
ht_cap = ath10k_get_ht_cap(ar);
|
|
vht_cap = ath10k_create_vht_cap(ar);
|
|
|
|
if (ar->phy_capability & WHAL_WLAN_11G_CAPABILITY) {
|
|
channels = kmemdup(ath10k_2ghz_channels,
|
|
sizeof(ath10k_2ghz_channels),
|
|
GFP_KERNEL);
|
|
if (!channels) {
|
|
ret = -ENOMEM;
|
|
goto err_free;
|
|
}
|
|
|
|
band = &ar->mac.sbands[IEEE80211_BAND_2GHZ];
|
|
band->n_channels = ARRAY_SIZE(ath10k_2ghz_channels);
|
|
band->channels = channels;
|
|
band->n_bitrates = ath10k_g_rates_size;
|
|
band->bitrates = ath10k_g_rates;
|
|
band->ht_cap = ht_cap;
|
|
|
|
/* vht is not supported in 2.4 GHz */
|
|
|
|
ar->hw->wiphy->bands[IEEE80211_BAND_2GHZ] = band;
|
|
}
|
|
|
|
if (ar->phy_capability & WHAL_WLAN_11A_CAPABILITY) {
|
|
channels = kmemdup(ath10k_5ghz_channels,
|
|
sizeof(ath10k_5ghz_channels),
|
|
GFP_KERNEL);
|
|
if (!channels) {
|
|
ret = -ENOMEM;
|
|
goto err_free;
|
|
}
|
|
|
|
band = &ar->mac.sbands[IEEE80211_BAND_5GHZ];
|
|
band->n_channels = ARRAY_SIZE(ath10k_5ghz_channels);
|
|
band->channels = channels;
|
|
band->n_bitrates = ath10k_a_rates_size;
|
|
band->bitrates = ath10k_a_rates;
|
|
band->ht_cap = ht_cap;
|
|
band->vht_cap = vht_cap;
|
|
ar->hw->wiphy->bands[IEEE80211_BAND_5GHZ] = band;
|
|
}
|
|
|
|
ar->hw->wiphy->interface_modes =
|
|
BIT(NL80211_IFTYPE_STATION) |
|
|
BIT(NL80211_IFTYPE_AP);
|
|
|
|
ar->hw->wiphy->available_antennas_rx = ar->supp_rx_chainmask;
|
|
ar->hw->wiphy->available_antennas_tx = ar->supp_tx_chainmask;
|
|
|
|
if (!test_bit(ATH10K_FW_FEATURE_NO_P2P, ar->fw_features))
|
|
ar->hw->wiphy->interface_modes |=
|
|
BIT(NL80211_IFTYPE_P2P_DEVICE) |
|
|
BIT(NL80211_IFTYPE_P2P_CLIENT) |
|
|
BIT(NL80211_IFTYPE_P2P_GO);
|
|
|
|
ar->hw->flags = IEEE80211_HW_SIGNAL_DBM |
|
|
IEEE80211_HW_SUPPORTS_PS |
|
|
IEEE80211_HW_SUPPORTS_DYNAMIC_PS |
|
|
IEEE80211_HW_SUPPORTS_UAPSD |
|
|
IEEE80211_HW_MFP_CAPABLE |
|
|
IEEE80211_HW_REPORTS_TX_ACK_STATUS |
|
|
IEEE80211_HW_HAS_RATE_CONTROL |
|
|
IEEE80211_HW_AP_LINK_PS |
|
|
IEEE80211_HW_SPECTRUM_MGMT;
|
|
|
|
ar->hw->wiphy->features |= NL80211_FEATURE_STATIC_SMPS;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_DYNAMIC_SMPS)
|
|
ar->hw->wiphy->features |= NL80211_FEATURE_DYNAMIC_SMPS;
|
|
|
|
if (ar->ht_cap_info & WMI_HT_CAP_ENABLED) {
|
|
ar->hw->flags |= IEEE80211_HW_AMPDU_AGGREGATION;
|
|
ar->hw->flags |= IEEE80211_HW_TX_AMPDU_SETUP_IN_HW;
|
|
}
|
|
|
|
ar->hw->wiphy->max_scan_ssids = WLAN_SCAN_PARAMS_MAX_SSID;
|
|
ar->hw->wiphy->max_scan_ie_len = WLAN_SCAN_PARAMS_MAX_IE_LEN;
|
|
|
|
ar->hw->vif_data_size = sizeof(struct ath10k_vif);
|
|
ar->hw->sta_data_size = sizeof(struct ath10k_sta);
|
|
|
|
ar->hw->max_listen_interval = ATH10K_MAX_HW_LISTEN_INTERVAL;
|
|
|
|
ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;
|
|
ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_CHANNEL_SWITCH;
|
|
ar->hw->wiphy->max_remain_on_channel_duration = 5000;
|
|
|
|
ar->hw->wiphy->flags |= WIPHY_FLAG_AP_UAPSD;
|
|
ar->hw->wiphy->features |= NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE;
|
|
|
|
/*
|
|
* on LL hardware queues are managed entirely by the FW
|
|
* so we only advertise to mac we can do the queues thing
|
|
*/
|
|
ar->hw->queues = 4;
|
|
|
|
switch (ar->wmi.op_version) {
|
|
case ATH10K_FW_WMI_OP_VERSION_MAIN:
|
|
case ATH10K_FW_WMI_OP_VERSION_TLV:
|
|
ar->hw->wiphy->iface_combinations = ath10k_if_comb;
|
|
ar->hw->wiphy->n_iface_combinations =
|
|
ARRAY_SIZE(ath10k_if_comb);
|
|
ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_ADHOC);
|
|
break;
|
|
case ATH10K_FW_WMI_OP_VERSION_10_1:
|
|
case ATH10K_FW_WMI_OP_VERSION_10_2:
|
|
ar->hw->wiphy->iface_combinations = ath10k_10x_if_comb;
|
|
ar->hw->wiphy->n_iface_combinations =
|
|
ARRAY_SIZE(ath10k_10x_if_comb);
|
|
break;
|
|
case ATH10K_FW_WMI_OP_VERSION_UNSET:
|
|
case ATH10K_FW_WMI_OP_VERSION_MAX:
|
|
WARN_ON(1);
|
|
ret = -EINVAL;
|
|
goto err_free;
|
|
}
|
|
|
|
ar->hw->netdev_features = NETIF_F_HW_CSUM;
|
|
|
|
if (config_enabled(CONFIG_ATH10K_DFS_CERTIFIED)) {
|
|
/* Init ath dfs pattern detector */
|
|
ar->ath_common.debug_mask = ATH_DBG_DFS;
|
|
ar->dfs_detector = dfs_pattern_detector_init(&ar->ath_common,
|
|
NL80211_DFS_UNSET);
|
|
|
|
if (!ar->dfs_detector)
|
|
ath10k_warn(ar, "failed to initialise DFS pattern detector\n");
|
|
}
|
|
|
|
ret = ath_regd_init(&ar->ath_common.regulatory, ar->hw->wiphy,
|
|
ath10k_reg_notifier);
|
|
if (ret) {
|
|
ath10k_err(ar, "failed to initialise regulatory: %i\n", ret);
|
|
goto err_free;
|
|
}
|
|
|
|
ret = ieee80211_register_hw(ar->hw);
|
|
if (ret) {
|
|
ath10k_err(ar, "failed to register ieee80211: %d\n", ret);
|
|
goto err_free;
|
|
}
|
|
|
|
if (!ath_is_world_regd(&ar->ath_common.regulatory)) {
|
|
ret = regulatory_hint(ar->hw->wiphy,
|
|
ar->ath_common.regulatory.alpha2);
|
|
if (ret)
|
|
goto err_unregister;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err_unregister:
|
|
ieee80211_unregister_hw(ar->hw);
|
|
err_free:
|
|
kfree(ar->mac.sbands[IEEE80211_BAND_2GHZ].channels);
|
|
kfree(ar->mac.sbands[IEEE80211_BAND_5GHZ].channels);
|
|
|
|
return ret;
|
|
}
|
|
|
|
void ath10k_mac_unregister(struct ath10k *ar)
|
|
{
|
|
ieee80211_unregister_hw(ar->hw);
|
|
|
|
if (config_enabled(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector)
|
|
ar->dfs_detector->exit(ar->dfs_detector);
|
|
|
|
kfree(ar->mac.sbands[IEEE80211_BAND_2GHZ].channels);
|
|
kfree(ar->mac.sbands[IEEE80211_BAND_5GHZ].channels);
|
|
|
|
SET_IEEE80211_DEV(ar->hw, NULL);
|
|
}
|